MSERIES-PORT-MIB
The MSERIES-PORT-MIB provides vendor-specific SNMP access to monitor and manage physical port interfaces, link states, and traffic counters on Ciena SmartOptics M-Series optical transport equipment.
Imported Objects
Objects
20 total| Object Name |
|---|
smartPortThis is the enterprise specific Port MIB for SmartOptics M-Series. MODULE-IDENTITY .1.3.6.1.4.1.30826.1.3 |
smartPortObjects OBJECT IDENTIFIER .1.3.6.1.4.1.30826.1.3.1 |
smartPortGeneral OBJECT IDENTIFIER .1.3.6.1.4.1.30826.1.3.1.1 |
smartPortList OBJECT IDENTIFIER .1.3.6.1.4.1.30826.1.3.1.2 |
smartPortTableA port table. SEQUENCE OF SmartPortEntry .1.3.6.1.4.1.30826.1.3.1.2.1 |
smartPortEntryAn entry in the port list. SmartPortEntry .1.3.6.1.4.1.30826.1.3.1.2.1.1 |
smartPortIndexA unique index for each port that corresponds to the index in the interface tablero Unsigned32 .1.3.6.1.4.1.30826.1.3.1.2.1.1.1 |
smartPortNameThe name of the port.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.30826.1.3.1.2.1.1.2 |
smartPortAliasUser configurable Port Alias for the port. Not writeable in SmartOS v2.3rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.30826.1.3.1.2.1.1.3 |
smartPortTypeThe type of port. rx(1) - Receiving port. tx(2) - Transmitting port. biDi(3) - Bidirectional port.ro PortType (MSERIES-TC) .1.3.6.1.4.1.30826.1.3.1.2.1.1.4 |
smartPortPowerThe power level in units of 0.1 dBm.ro Integer32 .1.3.6.1.4.1.30826.1.3.1.2.1.1.5 |
smartPortStatusThe operational state for a port. idle(1) - The port is not activated down(2) - The port traffic is lost. up(3) - There is traffic on the port. high(4) - The port got to high power. low(5) - The port got to low power. eyeSafety(6) - The Line Tx port is in Eye Safety Mode. This means that either the connector on the Line Tx port is not inserted or that you have too strong reflection from the line fiber. cd(7) - Channel detected. ncd(8) - No channel detected.ro PortStatus (MSERIES-TC) .1.3.6.1.4.1.30826.1.3.1.2.1.1.6 |
smartPortModeThe Mode of the Port. normal (1) - The port is active. No alarms are beeing suppressed. service (2) . The port is in service mode and alarms are beeing suppressed. When service is ready smartPortMode should be set to 'normal' again. Not writeable in SmartOS v2.3rw PortMode (MSERIES-TC) .1.3.6.1.4.1.30826.1.3.1.2.1.1.7 |
smartPortHighPowerAlarmThresholdThe threshold for the High Power alarm. Not writeable in SmartOS v2.3rw Integer32 .1.3.6.1.4.1.30826.1.3.1.2.1.1.8 |
smartPortLowPowerAlarmThresholdThe threshold for the Low Power alarm. Not writeable in SmartOS v2.3rw Integer32 .1.3.6.1.4.1.30826.1.3.1.2.1.1.9 |
smartPortMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.30826.1.3.2 |
smartPortGroups OBJECT IDENTIFIER .1.3.6.1.4.1.30826.1.3.2.1 |
smartPortListGroupV1The Port List MIB objects v1. Unknown .1.3.6.1.4.1.30826.1.3.2.1.1 |
smartPortCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.30826.1.3.2.2 |
smartPortBasicComplV1Basic implementation requirements for the port MIB V1. Unknown .1.3.6.1.4.1.30826.1.3.2.2.1 |
More MIBs from SmartOptics
Browse all SmartOpticsMIBs →The DCP-INTERFACE-MIB enables monitoring and management of Smartoptics DCP (Digital Cross-Connect) interface parameters, including optical power levels, signal status, and port configuration states. This enterprise-specific module facilitates granular visibility into the physical and data link layer performance of Smartoptics optical transport hardware.
The MSERIES-ALARM-MIB module enables SNMP-based monitoring of critical fault conditions and operational alerts on Nokia SmartOptics M-Series optical transport hardware. It specifically tracks alarm states, severity levels, and event triggers to facilitate real-time network fault detection and troubleshooting within the optical layer.
The DCP-ALARM-MIB enables monitoring of alarm states and fault conditions on Smartoptics Dense Wavelength Division Multiplexing (DWDM) optical transport equipment. It provides enterprise-specific trap notifications and object definitions for tracking critical hardware and link integrity events within Smartoptics optical network infrastructure.
The DCP-OCH-MIB module enables monitoring and management of Smartoptics Dense Wavelength Division Multiplexing (DWDM) optical channel (OCH) hardware, specifically exposing performance metrics such as optical power levels, signal-to-noise ratios, and error counters for individual wavelength channels.
The DCP-LINKVIEW-MIB enables monitoring of Smartoptics Dense Wavelength Division Multiplexing (DWDM) optical transport links, specifically tracking per-channel optical power levels, signal-to-noise ratios, and link status states. This enterprise-specific module facilitates granular visibility into the physical layer performance and health of Smartoptics DCP (Digital Cross-Connect) equipment.
The MSERIES-ENVMON-MIB enables SNMP-based monitoring of environmental sensor data, including temperature, voltage, and fan status, on Alcatel-Lucent (Nokia) SmartOptics M-Series optical transport hardware. This enterprise-specific module facilitates real-time hardware health assessment and fault detection for critical network infrastructure components.