DCP-LINKVIEW-MIB
The DCP-LINKVIEW-MIB enables monitoring of Smartoptics Dense Wavelength Division Multiplexing (DWDM) optical transport links, specifically tracking per-channel optical power levels, signal-to-noise ratios, and link status states. This enterprise-specific module facilitates granular visibility into the physical layer performance and health of Smartoptics DCP (Digital Cross-Connect) equipment.
Imported Objects
Objects
25 total| Object Name |
|---|
dcpLinkviewThis is the enterprise specific DCP LINKVIEW MIB for Smartoptics MODULE-IDENTITY .1.3.6.1.4.1.30826.2.2.3 |
dcpLinkviewObjects OBJECT IDENTIFIER .1.3.6.1.4.1.30826.2.2.3.1 |
dcpLinkviewTableDescription. SEQUENCE OF DcpLinkviewEntry .1.3.6.1.4.1.30826.2.2.3.1.1 |
dcpLinkviewEntryDescription. DcpLinkviewEntry .1.3.6.1.4.1.30826.2.2.3.1.1.1 |
dcpLinkviewIndexInterface Index in the following format: csiixy where c: chassis. s: slot number. ii: Interface number. x: 1 = line, 2 = client. y: 0 = tx+rx port, 1 = tx port, 2 = rx port. For DCP-M products Slot is always 0. Same Index is used in the IF-MIB. Unsigned32 .1.3.6.1.4.1.30826.2.2.3.1.1.1.1 |
dcpLinkviewLocalHostnameThe hostname of the local system.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.30826.2.2.3.1.1.1.2 |
dcpLinkviewLocalNameThe local interface name. If no interface this value is empty. if-c/channelid-direction where c = chassis and direction = rx or tx.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.30826.2.2.3.1.1.1.3 |
dcpLinkviewLocalStatusThe operational state of the local port. idle - The port is not activated. down - The port traffic is lost. up - There is traffic on the port.ro InterfaceStatus (SO-TC-MIB) .1.3.6.1.4.1.30826.2.2.3.1.1.1.4 |
dcpLinkviewLocalPowerThe optical power present at the line interface, all wavelengths combined in units of 0.1 dBm.ro OpticalPower1Decimal (SO-TC-MIB) .1.3.6.1.4.1.30826.2.2.3.1.1.1.5 |
dcpLinkviewFiberLossThe fiber loss in units of 0.1 dB.ro DcpFiberLoss .1.3.6.1.4.1.30826.2.2.3.1.1.1.6 |
dcpLinkviewFiberAttenuationThe fiber attenuation in units of 0.01 dB/km.ro DcpFiberAttenuation .1.3.6.1.4.1.30826.2.2.3.1.1.1.7 |
dcpLinkviewFiberLengthThe fiber length in units of 0.1 km.ro DcpFiberLength .1.3.6.1.4.1.30826.2.2.3.1.1.1.8 |
dcpLinkviewFiberDispersionThe calculated dispersion based on the measured fiber length in units of 1 ps/nm.ro Unsigned32 .1.3.6.1.4.1.30826.2.2.3.1.1.1.9 |
dcpLinkviewFiberTypeThe fiber type configured, currently only G.652 is supported.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.30826.2.2.3.1.1.1.10 |
dcpLinkviewFiberDispCompThe compensated dispersion value by the system in units of 1 ps/nm.ro Integer32 (-10000..10000) .1.3.6.1.4.1.30826.2.2.3.1.1.1.11 |
dcpLinkviewFiberDispFinalResidiual(remaning) dispersion in units of 1 ps/nm.ro Integer32 (-10000..10000) .1.3.6.1.4.1.30826.2.2.3.1.1.1.12 |
dcpLinkviewFiberUtilizationWavelength utilization of the system in units of %.ro Gauge32 .1.3.6.1.4.1.30826.2.2.3.1.1.1.13 |
dcpLinkviewRemotePowerThe optical power of the remote interface in units of 0.1 dBm.ro OpticalPower1Decimal (SO-TC-MIB) .1.3.6.1.4.1.30826.2.2.3.1.1.1.14 |
dcpLinkviewRemoteNameThe remote interface name. If no interface this value is empty. if-c/channelid-direction where c = chassis and direction = rx or tx.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.30826.2.2.3.1.1.1.15 |
dcpLinkviewRemoteHostnameThe hostname of the remote system.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.30826.2.2.3.1.1.1.16 |
dcpLinkviewMIBCompliance OBJECT IDENTIFIER .1.3.6.1.4.1.30826.2.2.3.2 |
dcpLinkviewMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.30826.2.2.3.2.1 |
dcpLinkviewTableGroupV1The interface table objects V1. Unknown .1.3.6.1.4.1.30826.2.2.3.2.1.1 |
dcpLinkviewMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.30826.2.2.3.2.2 |
dcpLinkviewBasicComplV1Basic implementation requirements for the DCP-INTERFACE-MIB V1. Unknown .1.3.6.1.4.1.30826.2.2.3.2.2.1 |
More MIBs from SmartOptics
Browse all SmartOpticsMIBs →The DCP-INTERFACE-MIB enables monitoring and management of Smartoptics DCP (Digital Cross-Connect) interface parameters, including optical power levels, signal status, and port configuration states. This enterprise-specific module facilitates granular visibility into the physical and data link layer performance of Smartoptics optical transport hardware.
The MSERIES-ALARM-MIB module enables SNMP-based monitoring of critical fault conditions and operational alerts on Nokia SmartOptics M-Series optical transport hardware. It specifically tracks alarm states, severity levels, and event triggers to facilitate real-time network fault detection and troubleshooting within the optical layer.
The DCP-ALARM-MIB enables monitoring of alarm states and fault conditions on Smartoptics Dense Wavelength Division Multiplexing (DWDM) optical transport equipment. It provides enterprise-specific trap notifications and object definitions for tracking critical hardware and link integrity events within Smartoptics optical network infrastructure.
The DCP-OCH-MIB module enables monitoring and management of Smartoptics Dense Wavelength Division Multiplexing (DWDM) optical channel (OCH) hardware, specifically exposing performance metrics such as optical power levels, signal-to-noise ratios, and error counters for individual wavelength channels.
The MSERIES-PORT-MIB provides vendor-specific SNMP access to monitor and manage physical port interfaces, link states, and traffic counters on Ciena SmartOptics M-Series optical transport equipment.
The MSERIES-ENVMON-MIB enables SNMP-based monitoring of environmental sensor data, including temperature, voltage, and fan status, on Alcatel-Lucent (Nokia) SmartOptics M-Series optical transport hardware. This enterprise-specific module facilitates real-time hardware health assessment and fault detection for critical network infrastructure components.