LINKSYS-LLDP-MIB
AI MIB Summary
The LINKSYS-LLDP-MIB enables monitoring of Link Layer Discovery Protocol neighbor tables, device identification attributes, and port capabilities on Linksys network infrastructure. This private extension facilitates the retrieval of LLDP-specific operational data, including system name, location, and management IP addresses, for topology mapping and device discovery.
This private MIB module adds MIBs to LLDP (Link Layer Discovery Protocol).
Main OID:
rlLldp.1.3.6.1.4.1.89.110
47
Objects
Active
Status
10
Dependencies
Imported Objects
Objects
47 total| Object Name |
|---|
rlLldpTLVsTxOverloadingStateEnterTrapInformational trap indicating that the port has entered the overloading state. NOTIFICATION-TYPE .1.3.6.1.4.1.89.0.209 |
rlLldpTLVsTxOverloadingStateExitTrapInformational trap indicating that the port is no longer in the overloading state.. NOTIFICATION-TYPE .1.3.6.1.4.1.89.0.210 |
rlLldpThis private MIB module adds MIBs to LLDP (Link Layer Discovery Protocol). MODULE-IDENTITY .1.3.6.1.4.1.89.110 |
rlLldpObjects OBJECT IDENTIFIER .1.3.6.1.4.1.89.110.1 |
rlLldpConfig OBJECT IDENTIFIER .1.3.6.1.4.1.89.110.1.1 |
rlLldpEnabledSetting this variable to 'true' will globally enable the LLDP feature
(both transmit and receive functionalities). Setting this variable
to 'false' will globally disable the LLDP feature. Thus, the
administratively desired status of a local port is determined by
both this variable and the MIB lldpPortConfigAdminStatus.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.110.1.1.1 |
rlLldpClearRxA set of ports that are identified by a PortList, in which
each port is represented as a bit.
Clears the Rx information about the remote agents accordingly to the
specified PortList.
The default value for rlLldpClearRx object is an empty binary string,
which means no ports are specified to be cleared from the Rx Info.
This object behaviors as an event (write-only) than
reading this object always results in an Empty Port List of length zero.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.89.110.1.1.2 |
rlLldpDuModeAction with LLDPDU upon globally disabled LLDP.
If the associated rlLldpDuMode object has a value of
'filtering(1)', then received frames are containing LLDPDU
will be dropped.
If the associated rlLldpDuMode object has a value of
'flooding(2)', then received frames are containing LLDPDU
will flood all active ports.rw Enumeration .1.3.6.1.4.1.89.110.1.1.3 |
rlLldpAutoAdvLocPortManAddrTableThis table contains automaticaly selected management address,
advertised on the local port. SEQUENCE OF RlLldpAutoAdvLocPortManAddrEntry .1.3.6.1.4.1.89.110.1.1.4 |
rlLldpAutoAdvLocPortManAddrEntryInformation about a local port, which advertises the Management
address automatically. Entry also included an interface number, on
which the Management address is assigned.
Each management address should have distinct 'management address
type' (rlLldpAutoAdvManAddrSubtype) and 'management address'
(rlLldpAutoAdvManAddr). RlLldpAutoAdvLocPortManAddrEntry .1.3.6.1.4.1.89.110.1.1.4.1 |
rlLldpAutoAdvLocPortNumThe index value used to identify the port component
(contained in the local chassis with the LLDP agent)
associated with this entry.
The value of this object is used as a port index to the
rlLldpAutoAdvLocPortManAddrTable. LldpPortNumber (LLDP-MIB) .1.3.6.1.4.1.89.110.1.1.4.1.1 |
rlLldpAutoAdvManAddrOwnerIfIdThe integer value is used to identify the interface number
(port, trunk or vlan). The management address, automatically
advertised from associated 'rlLldpAutoAdvLocPortNum'local port is
assigned to mentioned 'rlLldpAutoAdvManAddrOwnerIfId' interface.
In case of 0 the management address is automatically calculated
without care to the ifIndex it was defined on.rw Integer32 .1.3.6.1.4.1.89.110.1.1.4.1.2 |
rlLldpAutoAdvManAddrNoneA value of 'true' indicates that the any management address hasn't advertised
by the local port. Moreover, the configuration of automatic management address
advertisment is disabled.
A value of 'false' indicates that the configuration of automatic management address
advertisment is enabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.110.1.1.4.1.3 |
rlLldpAutoAdvManAddrSubtypeThe type of management address identifier encoding used in
the associated 'rlLldpAutoAdvManAddr' object.ro AddressFamilyNumbers (IANA-ADDRESS-FAMILY-NUMBERS-MIB) .1.3.6.1.4.1.89.110.1.1.4.1.4 |
rlLldpAutoAdvManAddrThe string value used to identify the management address is
automaticaly advertised by local port, and assigned on the
associated 'rlLldpAutoAdvManAddrOwnerIfId' interface.ro LldpManAddress (LLDP-MIB) .1.3.6.1.4.1.89.110.1.1.4.1.5 |
rlLldpAutoAdvPortsStatusThe row status variable, used according to
row installation and removal conventions.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.110.1.1.4.1.6 |
rlLldpChassisIdSubtypeThe type of encoding used to identify the chassis
associated with the local system.rw Enumeration .1.3.6.1.4.1.89.110.1.1.5 |
rlLldpXMedConfig OBJECT IDENTIFIER .1.3.6.1.4.1.89.110.1.2 |
rlLldpXMedLocMediaPolicyContainerTableThis table contains one row per policy number
of media policy container configuration. SEQUENCE OF RlLldpXMedLocMediaPolicyContainerEntry .1.3.6.1.4.1.89.110.1.2.1 |
rlLldpXMedLocMediaPolicyContainerEntryConfiguration of a particular policy in the media policy container. RlLldpXMedLocMediaPolicyContainerEntry .1.3.6.1.4.1.89.110.1.2.1.1 |
rlLldpXMedLocMediaPolicyContainerIndexThe index value used to identify the Media Policy
associated with this entry.
The value of this object is used as a policy number index to the
rlLldpXMedLocMediaPolicyContainerTable. PolicyNumber .1.3.6.1.4.1.89.110.1.2.1.1.1 |
rlLldpXMedLocMediaPolicyContainerAppTypeThe media type that defines the primary function of the
application for the policy advertised by an endpoint.rw PolicyContainerAppType .1.3.6.1.4.1.89.110.1.2.1.1.2 |
rlLldpXMedLocMediaPolicyContainerVlanIDAn extension of the VLAN Identifier for the port,
as defined in IEEE 802.1P-1998.
A value of 1 through 4094 is used to define a valid PVID.
A value of 0 shall be used if the device is using priority tagged
frames, meaning that only the 802.1p priority level is significant
and the default VID of the ingress port is being used instead.
A value of 4095 is reserved for implementation use.rw Integer32 (0|1..4094|4095) .1.3.6.1.4.1.89.110.1.2.1.1.3 |
rlLldpXMedLocMediaPolicyContainerPriorityThis object contains the value of the 802.1p priority
which is associated with the given port on the
local system.rw Integer32 .1.3.6.1.4.1.89.110.1.2.1.1.4 |
rlLldpXMedLocMediaPolicyContainerDscpThis object contains the value of the Differentiated Service
Code Point (DSCP) as defined in IETF RFC 2474 and RFC 2475
which is associated with the given port on the local system.rw Dscp (DIFFSERV-DSCP-TC) .1.3.6.1.4.1.89.110.1.2.1.1.5 |
rlLldpXMedLocMediaPolicyContainerUnknownA value of 'true' indicates that the
network policy for the specified application type is
currently unknown. In this case, the VLAN ID, the
layer 2 priority and the DSCP value fields are ignored.
A value of 'false' indicates that this network policy
is definedrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.110.1.2.1.1.6 |
rlLldpXMedLocMediaPolicyContainerTaggedA value of 'true' indicates that the application is using a
tagged VLAN.
A value of 'false' indicates that for the specific application
the device either is using an untagged VLAN or does not
support port based VLAN operation. In this case, both the
VLAN ID and the Layer 2 priority fields are ignored and
only the DSCP value has relevancerw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.110.1.2.1.1.7 |
rlLldpXMedLocMediaPolicyContainerPortsA set of ports that are identified by a PortList, in which
each port is represented as a bit. The local Media Policy Number
will be associated with (or attached to) the ports specified at
the rlLldpXMedLocMediaPolicyContainerPorts.
The default value for rlLldpXMedLocMediaPolicyContainerPorts object
is empty binary string, which means no ports are specified
for advertising indicated management address instance.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.89.110.1.2.1.1.8 |
rlLldpXMedLocMediaPolicyContainerRowStatusThe row status variable, used according to
row installation and removal conventions.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.110.1.2.1.1.9 |
rlLldpTLVsTxOverloadingTableA table that show the which of the LLDP TLVs are not transmitted
on individual ports due to insufficient room in the frame
and the size of each TLV. SEQUENCE OF RlLldpTLVsTxOverloadingEntry .1.3.6.1.4.1.89.110.1.3 |
rlLldpTLVsTxOverloadingEntryLLDP TX overloading information that shows the
transmission of TLVs on LLDP transmission capable ports. RlLldpTLVsTxOverloadingEntry .1.3.6.1.4.1.89.110.1.3.1 |
rlLldpTxOverloadingPortNumThe value of this object is used as a port index to the
TLVs TX overloading Table . LldpPortNumber (LLDP-MIB) .1.3.6.1.4.1.89.110.1.3.1.1 |
rlLldpTxOverloadingIndexThe sequence number of the group into sent LLDP PPDU starting from 1. Unsigned32 .1.3.6.1.4.1.89.110.1.3.1.2 |
rlLldpTxOverloadingGroupIdDefines the TLVs groups.
A value of mandatory(1) defines LLDP mandatory TLVs group
A value of optinal(2) defines LLDP optional TLVs group
A value of medCap(3) defines LLDP MED - Capabilities group
A value of medLocation(4) defines LLDP MED - Location group
A value of medNetPolicy(5) defines LLDP MED - Network Policy group
A value of medPoe(6) defines LLDP MED - Extended Power via MDI group
A value of medInventory(7) defines LLDP MED - Inventory group
A value of Xdot3(8) defines 802.3 TLVs group
A value of Xdot1(9) defines 802.1 TLVs groupro Enumeration .1.3.6.1.4.1.89.110.1.3.1.3 |
rlLldpTLVsTxSizeThe size of the TLV in Bytes.ro Unsigned32 .1.3.6.1.4.1.89.110.1.3.1.4 |
rlLldpTLVsTxGroupOverloadingBoolean Flag, When TRUE indicating that LLDP TLVs were overloaded
and the value of left size is negativero TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.110.1.3.1.5 |
rlLldpTLVsTxLeftSizeThe size in Bytes of the available space left in the LLDPDU after adding the TLVs group.
In case the Overloading Flag is TRUE, there not enough space in the LLDPDU for the TLVs group
and this is the size of the additional scpace that required for the TLVs groupro Unsigned32 .1.3.6.1.4.1.89.110.1.3.1.6 |
rlLldpTLVsTxOverloadingSizeTableA table that show the total size of the all TLVs
and the LLDPDU free size . SEQUENCE OF RlLldpTLVsTxOverloadingSizeEntry .1.3.6.1.4.1.89.110.1.4 |
rlLldpTLVsTxOverloadingSizeEntryLLDP TX overloading information RlLldpTLVsTxOverloadingSizeEntry .1.3.6.1.4.1.89.110.1.4.1 |
rlLldpTotalTLVsTxSizeThe Total size of all TLVs group in Bytes.ro Unsigned32 .1.3.6.1.4.1.89.110.1.4.1.2 |
rlLldpTLVsTxOverloadingBoolean Flag, When TRUE indicating that LLDP TLVs group were overloaded
and the value of left size is negativero TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.110.1.4.1.3 |
rlLldpLeftTLVsTxSizeThe size in Bytes of the available space left in the LLDPDU after adding all TLVs group.
In case the Overloading Flag is TRUE, there not enough space in the LLDPDU for all the TLVs group
and this is the size of the additional scpace that required for all the TLVs groupro Unsigned32 .1.3.6.1.4.1.89.110.1.4.1.4 |
rlLldpTLVsTxOverloadingPortsPort list that represent the overloading state of each portro PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.89.110.1.5 |
rlLldpXMedNetPolVoiceUpdateModerw PolicyAppVoiceUpdateMode .1.3.6.1.4.1.89.110.1.7 |
rlLldpRemTtlTableThis table contains the remote device Time To Live LLDP TLV. SEQUENCE OF RlLldpRemTtlEntry .1.3.6.1.4.1.89.110.1.8 |
rlLldpRemTtlEntryLLDP Time To TTL remove TLV.
This uses the key as defind in lldpRemTable of the LLDP-MIB. RlLldpRemTtlEntry .1.3.6.1.4.1.89.110.1.8.1 |
rlLldpRemTtlThis object contains the remote device Time To Live LLDP TLV.ro Unsigned32 UNITS "seconds" .1.3.6.1.4.1.89.110.1.8.1.1 |