LINKSYS-BRIDGEMIBOBJECTS-MIB
AI MIB Summary
The LINKSYS-BRIDGEMIBOBJECTS-MIB extends standard bridge management capabilities to monitor Linksys-specific bridge forwarding tables, MAC address aging timers, and port state transitions on Linksys Layer 2 switching hardware. This private MIB enables granular visibility into bridge learning behavior and loop prevention mechanisms for Linksys network appliances.
This private MIB module defines bridge MIB objects private MIBs.
Main OID:
rlpBridgeMIBObjects.1.3.6.1.4.1.89.57
168
Objects
Active
Status
8
Dependencies
Imported Objects
Objects
168 total| Object Name |
|---|
rlpBridgeMIBObjectsThis private MIB module defines bridge MIB objects private MIBs. MODULE-IDENTITY .1.3.6.1.4.1.89.57 |
LINKSYS-MIBEach octet within this value specifies a set of eight
vlans, with the first octet specifying vlan 1 through
8, the second octet specifying vlan 9 through 16, etc.
Within each octet, the most significant bit represents
the lowest numbered vlan, and the least significant bit
represents the highest numbered vlan. Thus, each vlan
of the bridge is represented by a single bit within the
value of this object. If that bit has a value of '1'
then that vlan is included in the set of vlans; the vlan
is not included if its bit has a value of '0'.
VlanList1 represent vlans 1-1024 OCTET STRING .1.3.6.1.4.1.89.57 |
rldot1dPriority OBJECT IDENTIFIER .1.3.6.1.4.1.89.57.1 |
rldot1dPriorityMibVersionMIB's version, the current version is 1.ro INTEGER .1.3.6.1.4.1.89.57.1.1 |
rldot1dPriorityPortGroupTableA list of PortGroupNumber for each port. SEQUENCE OF Rldot1dPriorityPortGroupEntry .1.3.6.1.4.1.89.57.1.2 |
rldot1dPriorityPortGroupEntryAll ports belonging to a same group have
the same User Priority to Traffic Class mapping. Rldot1dPriorityPortGroupEntry .1.3.6.1.4.1.89.57.1.2.1 |
rldot1dPriorityPortGroupNumberA group, that port belongs to. All ports belonging
to a same group have the same User Priority to
Traffic Class mapping.ro INTEGER .1.3.6.1.4.1.89.57.1.2.1.1 |
rldot1dStp OBJECT IDENTIFIER .1.3.6.1.4.1.89.57.2 |
rldot1dStpMibVersionMIB's version, the current version is 2.ro INTEGER .1.3.6.1.4.1.89.57.2.1 |
rldot1dStpTypeSpecifies whether the device supports Spanning Tree per device,
or per group.ro Enumeration .1.3.6.1.4.1.89.57.2.2 |
rldot1dStpEnableEnable / Disable spanning tree. When working in per vlan mode
enable / disable STP per all vlans.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.57.2.3 |
rldot1dStpPortMustBelongToVlanSpecifies whether a port must belong to a VLAN in order
to participate in the STP.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.57.2.4 |
rldot1dStpExtendedPortNumberFormatSpecifies whether the STP uses the extended port fnumber format.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.57.2.5 |
rldot1dStpVlanTableA table that contains vlan-specific information
for the Spanning Tree Protocol. SEQUENCE OF Rldot1dStpVlanEntry .1.3.6.1.4.1.89.57.2.6 |
rldot1dStpVlanEntryA list of information maintained by every Vlan
about the Spanning Tree Protocol state for that
Vlan. Rldot1dStpVlanEntry .1.3.6.1.4.1.89.57.2.6.1 |
rldot1dStpVlanThe Vlan index.ro INTEGER .1.3.6.1.4.1.89.57.2.6.1.1 |
rldot1dStpVlanEnableSpecifies whether this vlan is STP enable or disablerw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.57.2.6.1.2 |
rldot1dStpTimeSinceTopologyChangeThe time (in hundredths of a second) since the
last time a topology change was detected by the
bridge entity.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.89.57.2.6.1.3 |
rldot1dStpTopChangesThe total number of topology changes detected by
this bridge since the management entity was last
reset or initialized.ro Counter .1.3.6.1.4.1.89.57.2.6.1.4 |
rldot1dStpDesignatedRootThe bridge identifier of the root of the spanning
tree as determined by the Spanning Tree Protocol
as executed by this node. This value is used as
the Root Identifier parameter in all Configuration
Bridge PDUs originated by this node.ro BridgeId (BRIDGE-MIB) .1.3.6.1.4.1.89.57.2.6.1.5 |
rldot1dStpRootCostThe cost of the path to the root as seen from
this bridge.ro INTEGER .1.3.6.1.4.1.89.57.2.6.1.6 |
rldot1dStpRootPortThe port number of the port which offers the
lowest cost path from this bridge to the root
bridge.ro INTEGER .1.3.6.1.4.1.89.57.2.6.1.7 |
rldot1dStpMaxAgeThe maximum age of Spanning Tree Protocol
information learned from the network on any port
before it is discarded, in units of hundredths of
a second. This is the actual value that this
bridge is currently using.ro Timeout (BRIDGE-MIB) .1.3.6.1.4.1.89.57.2.6.1.8 |
rldot1dStpHelloTimeThe amount of time between the transmission of
Configuration bridge PDUs by this node on any port
when it is the root of the spanning tree or trying
to become so, in units of hundredths of a second.
This is the actual value that this bridge is
currently using.ro Timeout (BRIDGE-MIB) .1.3.6.1.4.1.89.57.2.6.1.9 |
rldot1dStpHoldTimeThis time value determines the interval length
during which no more than two Configuration bridge
PDUs shall be transmitted by this node, in units
of hundredths of a second.ro INTEGER .1.3.6.1.4.1.89.57.2.6.1.10 |
rldot1dStpForwardDelayThis time value, measured in units of hundredths
of a second, controls how fast a port changes its
spanning state when moving towards the Forwarding
state. The value determines how long the port
stays in each of the Listening and Learning
states, which precede the Forwarding state. This
value is also used, when a topology change has
been detected and is underway, to age all dynamic
entries in the Forwarding Database. [Note that
this value is the one that this bridge is
currently using, in contrast to
dot1dStpBridgeForwardDelay which is the value that
this bridge and all others would start using
if/when this bridge were to become the root.]ro Timeout (BRIDGE-MIB) .1.3.6.1.4.1.89.57.2.6.1.11 |
rldot1dStpVlanPortTableA table that contains pair <vlan, port> specific information
for the Spanning Tree Protocol. SEQUENCE OF Rldot1dStpVlanPortEntry .1.3.6.1.4.1.89.57.2.7 |
rldot1dStpVlanPortEntryA list of information maintained by every pair <vlan, port>
about the Spanning Tree Protocol state for that pair. Rldot1dStpVlanPortEntry .1.3.6.1.4.1.89.57.2.7.1 |
rldot1dStpVlanPortVlanThe Vlan number that the port belongs to, and for which this entry
contains Spanning Tree Protocol management
information.ro INTEGER .1.3.6.1.4.1.89.57.2.7.1.1 |
rldot1dStpVlanPortPortThe port number of the port for which this entry
contains Spanning Tree Protocol management
information.ro INTEGER .1.3.6.1.4.1.89.57.2.7.1.2 |
rldot1dStpVlanPortPriorityThe value of the priority field which is
contained in the more significant 4 bits of the most
significant octet of the (2 octet long) Port ID.
The other octet of the Port ID is given by the value
of rldot1dStpVlanPort.rw INTEGER .1.3.6.1.4.1.89.57.2.7.1.3 |
rldot1dStpVlanPortStateThe port's current state as defined by application of
the Spanning Tree Protocol. This state controls what
action a port takes on reception of a frame.
If the bridge has detected a port that is malfunctioning
it will place that port into the broken(6) state. For ports
which are disabled (see dot1dStpVlanPortEnable), this object
will have a value of disabled(1).ro Enumeration .1.3.6.1.4.1.89.57.2.7.1.4 |
rldot1dStpVlanPortEnableThe enabled/disabled status of the port.rw Enumeration .1.3.6.1.4.1.89.57.2.7.1.5 |
rldot1dStpVlanPortPathCostThe contribution of this port to the path cost of
paths towards the spanning tree root which include
this port. 802.1D-1990 recommends that the
default value of this parameter be in inverse
proportion to the speed of the attached LAN.rw INTEGER .1.3.6.1.4.1.89.57.2.7.1.6 |
rldot1dStpVlanPortDesignatedRootThe unique Bridge Identifier of the Bridge
recorded as the Root in the Configuration BPDUs
transmitted by the Designated Bridge for the
segment to which the port is attached.ro BridgeId (BRIDGE-MIB) .1.3.6.1.4.1.89.57.2.7.1.7 |
rldot1dStpVlanPortDesignatedCostThe path cost of the Designated Port of the
segment connected to this port. This value is
compared to the Root Path Cost field in received
bridge PDUs.ro INTEGER .1.3.6.1.4.1.89.57.2.7.1.8 |
rldot1dStpVlanPortDesignatedBridgeThe Bridge Identifier of the bridge which this
port considers to be the Designated Bridge for
this port's segment.ro BridgeId (BRIDGE-MIB) .1.3.6.1.4.1.89.57.2.7.1.9 |
rldot1dStpVlanPortDesignatedPortThe Port Identifier of the port on the Designated
Bridge for this port's segment.ro OCTET STRING .1.3.6.1.4.1.89.57.2.7.1.10 |
rldot1dStpVlanPortForwardTransitionsThe number of times this port has transitioned
from the Learning state to the Forwarding state.ro Counter .1.3.6.1.4.1.89.57.2.7.1.11 |
rldot1dStpTrapVariable OBJECT IDENTIFIER .1.3.6.1.4.1.89.57.2.8 |
rldot1dStpTrapVrblifIndexThe ifIndex of port which STP status was changedro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.89.57.2.8.1 |
rldot1dStpTrapVrblVIDThe VID of VLAN to which the port belongs which STP status was changedro INTEGER .1.3.6.1.4.1.89.57.2.8.2 |
rldot1dStpTypeAfterResetNew mode of spaning tree supported by the device after the next reset.rw Enumeration .1.3.6.1.4.1.89.57.2.9 |
rldot1dStpMonitorTimeFactor of hello-time during which a port is monotored to determine if it is stable.rw INTEGER .1.3.6.1.4.1.89.57.2.10 |
rldot1dStpBpduCountThe number of bpdu that need to received for the link to be considered stable.rw INTEGER .1.3.6.1.4.1.89.57.2.11 |
rldot1dStpLastChangedThe last time any object in this table was changed
by SNMP or other local management means.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.89.57.2.12 |
rldot1dStpPortTableA table that contains extended pair port specific information. SEQUENCE OF Rldot1dStpPortEntry .1.3.6.1.4.1.89.57.2.13 |
rldot1dStpPortEntryA list of information maintained by every port
about the Spanning Tree Protocol state for that port. Rldot1dStpPortEntry .1.3.6.1.4.1.89.57.2.13.1 |
rldot1dStpPortPortThe port number of the port for which this entry
contains Spanning Tree Protocol management
information.ro INTEGER .1.3.6.1.4.1.89.57.2.13.1.1 |
rldot1dStpPortDampEnableSpecified if dampening is enabled on this port.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.57.2.13.1.2 |
rldot1dStpPortDampStableSpecified if the port is stable.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.57.2.13.1.3 |
rldot1dStpPortFilterBpduSpecified if this port should filter bpdus when stp is disabled.rw Enumeration .1.3.6.1.4.1.89.57.2.13.1.4 |
rldot1dStpPortBpduSentSpecified the number of bpdu sent from this port.ro Counter32 .1.3.6.1.4.1.89.57.2.13.1.5 |
rldot1dStpPortBpduReceivedSpecified the number of bpdu received in this port.ro Counter32 .1.3.6.1.4.1.89.57.2.13.1.6 |
rldot1dStpPortRoleSpecified the role of this this port.ro Enumeration .1.3.6.1.4.1.89.57.2.13.1.7 |
rldot1dStpBpduTypeSpecified the type of BPDU transmitted by this port.ro Enumeration .1.3.6.1.4.1.89.57.2.13.1.8 |
rldot1dStpPortRestrictedRoleIf TRUE causes the Port not to be selected as Root Port for the CIST or
any MSTI, even if it has the best spanning tree priority vector.
Such a Port will be selected as an Alternate Port after the Root Port
has been selected.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.57.2.13.1.9 |
rldot1dStpPortAutoEdgePortIf TRUE causes the Port when become up, to enter the blocking state,
and if during 3 seconds it doesn't receive a BPDU, it will enter
the forwarding state.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.57.2.13.1.10 |
rldot1dStpPortLoopbackSpecified loopback was detected on port.
Usable for only a short period of time if stp loopback guard is enabled
(since port enters into shutdown state).ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.57.2.13.1.11 |
rldot1dStpPortBpduOperStatusSpecified BPDU handling operative status for port.ro Enumeration .1.3.6.1.4.1.89.57.2.13.1.12 |
rldot1dStpPortsEnableEnable / Disable spanning tree on ports by default .ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.57.2.14 |
rldot1dStpTaggedFloodingflooding can be done in tagged bpdu .ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.57.2.15 |
rldot1dStpPortBelongToVlanDefaultThe default value of rldot1dStpPortMustBelongToVlan .ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.57.2.16 |
rldot1dStpEnableByDefaultThe default value of rldot1dStpEnable .ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.57.2.17 |
rldot1dStpPortToDefaultTo order port/s to revert to default setings .rw INTEGER .1.3.6.1.4.1.89.57.2.18 |
rldot1dStpSupportedTypeThe type of stp supported by the device.ro Enumeration .1.3.6.1.4.1.89.57.2.19 |
rldot1dStpEdgeportSupportInStpIf EdgePort is supported in stpCompatible mode .ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.57.2.20 |
rldot1dStpFilterBpduSpecified if the device should filter BPDUs when STP is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.57.2.21 |
rldot1dStpFloodBpduMethodSpecified flooding method:
1 - classic - untagged to all stp disabled ports
2 - bridging -normal bridging.rw Enumeration .1.3.6.1.4.1.89.57.2.22 |
rldot1dStpSeparatedBridges OBJECT IDENTIFIER .1.3.6.1.4.1.89.57.2.23 |
rldot1dStpSeparatedBridgesTableDefine if separated bridges feature is enabled for each interface. SEQUENCE OF Rldot1dStpSeparatedBridgesEntry .1.3.6.1.4.1.89.57.2.23.1 |
rldot1dStpSeparatedBridgesEntryDefines the contents of each line in the rlSeparatedBridgesTable table. Rldot1dStpSeparatedBridgesEntry .1.3.6.1.4.1.89.57.2.23.1.1 |
rldot1dStpSeparatedBridgesPortEnableThis variable indicates whether the separated bridge feature is enabled on a specified ifIndex.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.57.2.23.1.1.1 |
rldot1dStpSeparatedBridgesEnableEnable / Disable Separated Bridges Feature.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.57.2.23.2 |
rldot1dStpSeparatedBridgesAutoConfigEnable / Disable Separated Bridges Automatic Configuration.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.57.2.23.3 |
rldot1dStpPortBpduGuardTableA table that contains for each port whether it is bpdu guard . SEQUENCE OF Rldot1dStpPortBpduGuardEntry .1.3.6.1.4.1.89.57.2.24 |
rldot1dStpPortBpduGuardEntryA list of information maintained by every port
whether it is bpdu guard. Rldot1dStpPortBpduGuardEntry .1.3.6.1.4.1.89.57.2.24.1 |
rldot1dStpPortBpduGuardEnableSpecified if bpdu guard is enabled on this port.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.57.2.24.1.1 |
rldot1dStpLoopbackGuardEnableDefine if STP loopback guard feature is globally enabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.57.2.25 |
rldot1dStpDisabledPortStateTableDefine stp port state for each stp disabled interface.
This is auxiliary MIB emulates stp enabled port behaviour in ASIC for stp disabled port.
The MIB contains only stp disabled ports entries SEQUENCE OF Rldot1dStpDisabledPortStateEntry .1.3.6.1.4.1.89.57.2.26 |
rldot1dStpDisabledPortStateEntryDefines the contents of each line in the rldot1dStpDisabledPortStateTable table. Rldot1dStpDisabledPortStateEntry .1.3.6.1.4.1.89.57.2.26.1 |
rldot1dStpDisabledPortStateThe port's stp state as defined by external
application . This state controls what action a port takes on
reception of a frame.rw Enumeration .1.3.6.1.4.1.89.57.2.26.1.1 |
rldot1dExtBase OBJECT IDENTIFIER .1.3.6.1.4.1.89.57.3 |
rldot1dExtBaseMibVersionMIB's version, the current version is 1.ro INTEGER .1.3.6.1.4.1.89.57.3.1 |
rldot1dDeviceCapabilitiesIndicates the optional parts of private extension of
IEEE 802.1D and 802.1Q that are implemented by this
device and are manageable through this MIB.
Capabilities that are allowed on a per-port basis are
indicated in dot1dPortCapabilities.ro Bits .1.3.6.1.4.1.89.57.3.2 |
rldot1wRStp OBJECT IDENTIFIER .1.3.6.1.4.1.89.57.4 |
rldot1wRStpVlanEdgePortTableA table that contains pair <vlan, port> specific information
for the Rapid Spanning Tree Protocol. SEQUENCE OF Rldot1wRStpVlanEdgePortEntry .1.3.6.1.4.1.89.57.4.1 |
rldot1wRStpVlanEdgePortEntryA list of information maintained by every pair <vlan, port>
about the RAPID Spanning Tree Protocol state for that pair. Rldot1wRStpVlanEdgePortEntry .1.3.6.1.4.1.89.57.4.1.1 |
rldot1wRStpVlanEdgePortVlanThe Vlan number that the port belongs to, and for which this entry
contains Spanning Tree Protocol management information,
If STP per device then only one value of 1 is allowed.
If STP per a VLAN then all value of 1..4095 are allowed.ro INTEGER .1.3.6.1.4.1.89.57.4.1.1.1 |
rldot1wRStpVlanEdgePortPortThe port number of the port for which this entry
contains Spanning Tree Protocol management information.ro INTEGER .1.3.6.1.4.1.89.57.4.1.1.2 |
rldot1wRStpEdgePortStatusSpecifies whether this port is an Edge Port or notrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.57.4.1.1.3 |
rldot1wRStpForceVersionTableA table that contains <vlan> specific information
for the Rapid Spanning Tree Protocol. SEQUENCE OF Rldot1wRStpForceVersionEntry .1.3.6.1.4.1.89.57.4.2 |
rldot1wRStpForceVersionEntryA list of information maintained by every <vlan>
about the RAPID Spanning Tree Protocol state for that pair. Rldot1wRStpForceVersionEntry .1.3.6.1.4.1.89.57.4.2.1 |
rldot1wRStpForceVersionVlanThe Vlan number that the port belongs to, and for which this entry
contains Spanning Tree Protocol management information,
If STP per device then only one value of 1 is allowed.
If STP per a VLAN then all value of 1..4095 are allowed.ro INTEGER .1.3.6.1.4.1.89.57.4.2.1.1 |
rldot1wRStpForceVersionStateSpecifies whether this Bridge uses the normal RSTP algorithm,
or STP Compatibility algorythm:
0 - STP Compatibility
2 - Normal RSTPrw INTEGER .1.3.6.1.4.1.89.57.4.2.1.2 |
rldot1pPriorityMap OBJECT IDENTIFIER .1.3.6.1.4.1.89.57.5 |
rldot1pPriorityMapStateenable / disablerw Enumeration .1.3.6.1.4.1.89.57.5.1 |
rldot1pPriorityMapTableThis table hold information the priority maps SEQUENCE OF Rldot1pPriorityMapEntry .1.3.6.1.4.1.89.57.5.2 |
rldot1pPriorityMapEntryThe row definition for this table. Rldot1pPriorityMapEntry .1.3.6.1.4.1.89.57.5.2.1 |
rldot1pPriorityMapNameThe map namero DisplayString .1.3.6.1.4.1.89.57.5.2.1.1 |
rldot1pPriorityMapPriorityThe map holding the queuerw OCTET STRING .1.3.6.1.4.1.89.57.5.2.1.2 |
rldot1pPriorityMapPortthe port that the map, is applied on in configrw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.89.57.5.2.1.3 |
rldot1pPriorityMapPortListthe ports that the map, is applied on in actualro PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.89.57.5.2.1.4 |
rldot1pPriorityMapStatusThe status of the table entry. It's used to delete an entryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.57.5.2.1.5 |
rldot1sMstp OBJECT IDENTIFIER .1.3.6.1.4.1.89.57.6 |
rldot1sMstpInstanceTableA table that contains Mstp instance specific information
for the Multiple Spanning Tree Protocol. SEQUENCE OF Rldot1sMstpInstanceEntry .1.3.6.1.4.1.89.57.6.1 |
rldot1sMstpInstanceEntryA list of information maintained by every instance
about the multiple Spanning Tree Protocol state for
that instance. Rldot1sMstpInstanceEntry .1.3.6.1.4.1.89.57.6.1.1 |
rldot1sMstpInstanceIdThe Instance index.ro INTEGER .1.3.6.1.4.1.89.57.6.1.1.1 |
rldot1sMstpInstanceEnableSpecifies whether this Instance is STP enable or disablero TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.57.6.1.1.2 |
rldot1sMstpInstanceTimeSinceTopologyChangeThe time (in hundredths of a second) since the
last time a topology change was detected by the
Mstp Instance .ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.89.57.6.1.1.3 |
rldot1sMstpInstanceTopChangesThe total number of topology changes detected by
this Instance since the management entity was last
reset or initialized.ro Counter .1.3.6.1.4.1.89.57.6.1.1.4 |
rldot1sMstpInstanceDesignatedRootThe bridge identifier of the root of the spanning
tree as determined by the Muliple Spanning Tree Protocol
as executed by this node. This value is used as
the Root Identifier parameter in all Configuration
Bridge PDUs originated by this node.ro BridgeId (BRIDGE-MIB) .1.3.6.1.4.1.89.57.6.1.1.5 |
rldot1sMstpInstanceRootCostThe cost of the path to the root as seen from
this bridge.ro INTEGER .1.3.6.1.4.1.89.57.6.1.1.6 |
rldot1sMstpInstanceRootPortThe port number of the port which offers the
lowest cost path from this bridge to the root
bridge.ro INTEGER .1.3.6.1.4.1.89.57.6.1.1.7 |
rldot1sMstpInstanceMaxAgeThe maximum age of Spanning Tree Protocol
information learned from the network on any port
before it is discarded, in units of hundredths of
a second. This is the actual value that this
bridge is currently using.ro Timeout (BRIDGE-MIB) .1.3.6.1.4.1.89.57.6.1.1.8 |
rldot1sMstpInstanceHelloTimeThe amount of time between the transmission of
Configuration bridge PDUs by this node on any port
when it is the root of the spanning tree or trying
to become so, in units of hundredths of a second.
This is the actual value that this bridge is
currently using.ro Timeout (BRIDGE-MIB) .1.3.6.1.4.1.89.57.6.1.1.9 |
rldot1sMstpInstanceHoldTimeThis time value determines the interval length
during which no more than two Configuration bridge
PDUs shall be transmitted by this node, in units
of hundredths of a second.ro INTEGER .1.3.6.1.4.1.89.57.6.1.1.10 |
rldot1sMstpInstanceForwardDelayThis time value, measured in units of hundredths
of a second, controls how fast a port changes its
spanning state when moving towards the Forwarding
state. The value determines how long the port
stays in each of the Listening and Learning
states, which precede the Forwarding state. This
value is also used, when a topology change has
been detected and is underway, to age all dynamic
entries in the Forwarding Database. [Note that
this value is the one that this bridge is
currently using, in contrast to
dot1dStpBridgeForwardDelay which is the value that
this bridge and all others would start using
if/when this bridge were to become the root.]ro Timeout (BRIDGE-MIB) .1.3.6.1.4.1.89.57.6.1.1.11 |
rldot1sMstpInstancePriorityThe value of the write-able portion of the Bridge
ID, i.e., the first four bits of the first octet
of the (8 octet long) Bridge ID.The value is a product
of 4096. The next 12 bit are the msti id .
The other (last) 6 octets of the Bridge ID are given
by the value of dot1dBaseBridgeAddress.rw INTEGER .1.3.6.1.4.1.89.57.6.1.1.12 |
rldot1sMstpInstanceRemainingHopesThis count value determines the amount of hopes
the information transmited by this bridge on this
instance can travel.ro INTEGER .1.3.6.1.4.1.89.57.6.1.1.13 |
rldot1sMstpInstancePortTableA table that contains pair <msti, port> specific information
for the Spanning Tree Protocol. SEQUENCE OF Rldot1sMstpInstancePortEntry .1.3.6.1.4.1.89.57.6.2 |
rldot1sMstpInstancePortEntryA list of information maintained by every pair <msti, port>
about the Spanning Tree Protocol state for that pair. Rldot1sMstpInstancePortEntry .1.3.6.1.4.1.89.57.6.2.1 |
rldot1sMstpInstancePortMstiIdThe Vlan group number that the port belongs to, and for which this entry
contains Spanning Tree Protocol management
information.ro INTEGER .1.3.6.1.4.1.89.57.6.2.1.1 |
rldot1sMstpInstancePortPortThe port number of the port for which this entry
contains Spanning Tree Protocol management
information.ro INTEGER .1.3.6.1.4.1.89.57.6.2.1.2 |
rldot1sMstpInstancePortPriorityThe value of the priority field which is
contained in the more significant 4 bits of the most
significant octet of the (2 octet long) Port ID.
The value is a product of 16.
The other octet of the Port ID is given by the value
of rldot1dStpVlanGroupPort.rw INTEGER .1.3.6.1.4.1.89.57.6.2.1.3 |
rldot1sMstpInstancePortStateThe port's current state as defined by application of
the Spanning Tree Protocol. This state controls what
action a port takes on reception of a frame.
If the bridge has detected a port that is malfunctioning
it will place that port into the broken(6) state. For ports
which are disabled (see dot1dStpVlanPortEnable), this object
will have a value of disabled(1).ro Enumeration .1.3.6.1.4.1.89.57.6.2.1.4 |
rldot1sMstpInstancePortEnableThe enabled/disabled status of the port.ro Enumeration .1.3.6.1.4.1.89.57.6.2.1.5 |
rldot1sMstpInstancePortPathCostThe contribution of this port to the path cost of
paths towards the spanning tree root which include
this port. 802.1D-1990 recommends that the
default value of this parameter be in inverse
proportion to the speed of the attached LAN.ro INTEGER .1.3.6.1.4.1.89.57.6.2.1.6 |
rldot1sMstpInstancePortDesignatedRootThe unique Bridge Identifier of the Bridge
recorded as the Root in the Configuration BPDUs
transmitted by the Designated Bridge for the
segment to which the port is attached.ro BridgeId (BRIDGE-MIB) .1.3.6.1.4.1.89.57.6.2.1.7 |
rldot1sMstpInstancePortDesignatedCostThe path cost of the Designated Port of the
segment connected to this port. This value is
compared to the Root Path Cost field in received
bridge PDUs.ro INTEGER .1.3.6.1.4.1.89.57.6.2.1.8 |
rldot1sMstpInstancePortDesignatedBridgeThe Bridge Identifier of the bridge which this
port considers to be the Designated Bridge for
this port's segment.ro BridgeId (BRIDGE-MIB) .1.3.6.1.4.1.89.57.6.2.1.9 |
rldot1sMstpInstancePortDesignatedPortThe Port Identifier of the port on the Designated
Bridge for this port's segment.ro OCTET STRING .1.3.6.1.4.1.89.57.6.2.1.10 |
rldot1sMstpInstancePortForwardTransitionsThe number of times this port has transitioned
from the Learning state to the Forwarding state.ro Counter .1.3.6.1.4.1.89.57.6.2.1.11 |
rldot1sMStpInstancePortAdminPathCostThe administratively assigned value for the contribution
of this port to the path cost of paths towards the spanning
tree root.
Writing a value of '0' assigns the automatically calculated
default Path Cost value to the port. If the default Path
Cost is being used, this object returns '0' when read.
This complements the object dot1dStpPortPathCost, which
returns the operational value of the path cost.rw INTEGER .1.3.6.1.4.1.89.57.6.2.1.12 |
rldot1sMStpInstancePortRoleSpecify the role of this this port.ro Enumeration .1.3.6.1.4.1.89.57.6.2.1.13 |
rldot1sMstpMaxHopesMax number of hopes that an MST BPDU will travel inside a region.rw INTEGER .1.3.6.1.4.1.89.57.6.3 |
rldot1sMstpConfigurationNameThe active configuration name as will be caried in MST BPDU's.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.89.57.6.4 |
rldot1sMstpRevisionLevelThe active revision level.ro INTEGER .1.3.6.1.4.1.89.57.6.5 |
rldot1sMstpVlanTableA table that contains information about the alocation of vlans to groups. SEQUENCE OF Rldot1sMstpVlanEntry .1.3.6.1.4.1.89.57.6.6 |
rldot1sMstpVlanEntryA list of information maintained by every vlan
about the group it belongs to. Rldot1sMstpVlanEntry .1.3.6.1.4.1.89.57.6.6.1 |
rldot1sMstpVlanThe vlan number of the vlan for which this entry
contains Spanning Tree Protocol management
information.ro INTEGER .1.3.6.1.4.1.89.57.6.6.1.1 |
rldot1sMstpGroupSpecifid the active group number this vlan belonges to.ro INTEGER .1.3.6.1.4.1.89.57.6.6.1.2 |
rldot1sMstpPendingGroupSpecifid the pending group number this vlan belonges to.rw INTEGER .1.3.6.1.4.1.89.57.6.6.1.3 |
rldot1sMstpExtPortTableA table that contains MSTP information about ports of the CIST. SEQUENCE OF Rldot1sMstpExtPortEntry .1.3.6.1.4.1.89.57.6.7 |
rldot1sMstpExtPortEntryA list of information maintained by every port
of the CIST. Rldot1sMstpExtPortEntry .1.3.6.1.4.1.89.57.6.7.1 |
rldot1sMstpExtPortPortThe port number of the port for which this entry
contains Spanning Tree Protocol management
information.ro INTEGER .1.3.6.1.4.1.89.57.6.7.1.1 |
rldot1sMstpExtPortInternalOperPathCostThe contribution of this port to the path cost of
paths towards the spanning tree regional root which
include this port. 802.1S-2002 recommends that the
default value of this parameter be in inverse
proportion to the speed of the attached LAN.ro INTEGER .1.3.6.1.4.1.89.57.6.7.1.2 |
rldot1sMstpExtPortDesignatedRegionalRootThe unique Bridge Identifier of the Bridge
recorded as the Root in the Configuration BPDUs
transmitted by the Designated Bridge for the
segment to which the port is attached.ro BridgeId (BRIDGE-MIB) .1.3.6.1.4.1.89.57.6.7.1.3 |
rldot1sMstpExtPortDesignatedRegionalCostThe regional path cost of the Designated Port of the
segment connected to this port. This value is
compared to the Root Path Cost field in received
bridge PDUs.ro INTEGER .1.3.6.1.4.1.89.57.6.7.1.4 |
rldot1sMstpExtPortBoundaryIndication if the port is conented to to a lan segment
outside or inside the region.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.57.6.7.1.5 |
rldot1sMstpExtPortInternalAdminPathCostThe administratively assigned value for the contribution
of this port to the path cost of paths towards the spanning
tree root.
Writing a value of '0' assigns the automatically calculated
default Path Cost value to the port. If the default Path
Cost is being used, this object returns '0' when read.
This complements the object dot1dStpPortPathCost, which
returns the operational value of the path cost.rw INTEGER .1.3.6.1.4.1.89.57.6.7.1.6 |
rldot1sMstpDesignatedMaxHopesMax number of hopes that an MST BPDU will travel inside a region.ro INTEGER .1.3.6.1.4.1.89.57.6.8 |
rldot1sMstpRegionalRootCIST Regional Root Identifier (13.16.4).
The Bridge Identifier of the current CIST Regional Root.ro BridgeId (BRIDGE-MIB) .1.3.6.1.4.1.89.57.6.9 |
rldot1sMstpRegionalRootCostThe CIST path cost from the transmitting Bridge to the
CIST Regional Root.ro INTEGER .1.3.6.1.4.1.89.57.6.10 |
rldot1sMstpPendingConfigurationNameThe pending configuration name.rw SnmpAdminString .1.3.6.1.4.1.89.57.6.11 |
rldot1sMstpPendingRevisionLevelThe pending revision level.rw INTEGER .1.3.6.1.4.1.89.57.6.12 |
rldot1sMstpPendingActionThe action to be done with the pending configuration.
copyPendingActive - to copy the pending mst configuration to the active one.
copyActivePending - to copy the active mst configuration to the pending one.rw Enumeration .1.3.6.1.4.1.89.57.6.13 |
rldot1sMstpRemainingHopsThis count value determines the amount of hops
the information transmitted by this bridge can travel.ro INTEGER .1.3.6.1.4.1.89.57.6.14 |
rldot1sMstpInstanceVlanTableThis table contains vlan lists per MSTP instances. SEQUENCE OF Rldot1sMstpInstanceVlanEntry .1.3.6.1.4.1.89.57.6.15 |
rldot1sMstpInstanceVlanEntryThe entry contains vlan lists per specific MSTP instance. Rldot1sMstpInstanceVlanEntry .1.3.6.1.4.1.89.57.6.15.1 |
rldot1sMstpInstanceVlanIdSpecifiy the instance number.ro INTEGER .1.3.6.1.4.1.89.57.6.15.1.1 |
rldot1sMstpInstanceVlanId1To1024first VlanId List of specific MSTP instance.ro VlanList1 .1.3.6.1.4.1.89.57.6.15.1.2 |
rldot1sMstpInstanceVlanId1025To2048second VlanId List of specific MSTP instance.ro VlanList2 .1.3.6.1.4.1.89.57.6.15.1.3 |
rldot1sMstpInstanceVlanId2049To3072third VlanId List of specific MSTP instance.ro VlanList3 .1.3.6.1.4.1.89.57.6.15.1.4 |
rldot1sMstpInstanceVlanId3073To4094fourth VlanId List of specific MSTP instance.ro VlanList4 .1.3.6.1.4.1.89.57.6.15.1.5 |
rldot1dTpAgingTime OBJECT IDENTIFIER .1.3.6.1.4.1.89.57.7 |
rldot1dTpAgingTimeMinThe min timeout period in seconds for aging out
dynamically learned forwarding information.ro INTEGER .1.3.6.1.4.1.89.57.7.1 |
rldot1dTpAgingTimeMaxThe max timeout period in seconds for aging out
dynamically learned forwarding information.ro INTEGER .1.3.6.1.4.1.89.57.7.2 |