Fore-Switch-MIB
Fore Switch MIB
Main OID:
foreSwitchModule.1.3.6.1.4.1.326.2.7
1850
Objects
Active
Status
10
Dependencies
Imported Objects
Objects
1850 total| Object Name |
|---|
asxSwLinkDownAn asxSwLinkDown trap signifies that the sending protocol entity recognizes a failure in one of the ATM Switch links that is connected to another switch. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.0 |
asxSwLinkUpAn asxSwLinkUp trap signifies that the sending protocol entity recognizes that one of the ATM Switch links that is connected to another switch has come up. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1 |
asxHostLinkDownAn asxHostLinkDown trap signifies that the sending protocol entity recognizes a failure in one of the ATM Switch links that is connected to a host. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.2 |
asxHostLinkUpAn asxHostLinkUp trap signifies that the sending protocol entity recognizes that one of the ATM Switch links that is connected to a host has come up. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.3 |
asxNetModuleDownAn asxNetModuleDown trap signifies that the sending protocol entity recognizes a failure in one of the ATM Switch network modules, that is identified by the board and the module numbers. This is probably caused by a hot-swap of a network module. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.4 |
asxNetModuleUpAn asxNetModuleUp trap signifies that the sending protocol entity recognizes a new operational ATM Switch network module, that is identified by the board and the module numbers. This is probably caused by a hot-swap of a network module. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.5 |
asxPsInputDownThis trap alerts that one ATM switch power supply failed due to failure in the input voltage. The power supply that failed is identified by the power supply index. Note that an input voltage may be out of spec and may not cause a power supply failure if high loads are not applied. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.6 |
asxPsInputUpThis trap alerts that one ATM switch power supply that had an input failure is up. The power supply that is back up is identified by the power supply index. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.7 |
asxPsOutputDownThis trap alerts that one ATM switch power supply output failed, or the power supply was physically removed. The power supply that failed is identified by the power supply index. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.9 |
asxPsOutputUpThis trap alerts that one ATM switch power supply that had an output failure or was removed is now up. The power supply that is back up is identified by the power supply index. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.10 |
asxFanBankDownThis trap alerts that one ATM switch fan bank failed. The fan bank that failed is identified by the fan bank index. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.22 |
asxFanBankUpThis trap alerts that one ATM switch fan bank is up. The fan bank that is back up is identified by the fan bank index. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.23 |
asxLinkDownThis trap alerts that the link that is identified by portName was configured up, but its underlying physical layer has lost its carrier (or the framing bit) and is currently down. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.28 |
asxLinkUpThis trap alerts that the link that is identified by portName is back up. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.29 |
asxSpansDownThis trap alerts that the SPANS signalling on the link that is identified by the sigPathPort and sigPathVPI failed. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.30 |
asxSpansUpThis trap alerts that the SPANS signalling on the link that is identified by the sigPathPort and sigPathVPI is up. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.31 |
asxTempSensorOverTempThis trap alerts that one of the temperature sensors indicates over temperature. The temperature sensor is identified by the temperature sensor index. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.32 |
asxTempSensorRegularTempThis trap alerts that one of the temperature sensors indicates regular temperature. The temperature sensor is identified by the temperature sensor index. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.33 |
asxFabricTemperatureOverTempThis trap alerts that one of the temperature sensors indicates over temperature. The temperature sensor is identified by the temperature sensor index. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.34 |
asxFabricTemperatureRegularTempThis trap alerts that one of the temperature sensors indicates regular temperature. The temperature sensor is identified by the temperature sensor index. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.35 |
asxSonetLOSDetectedThis trap indicates that the specified SONET port is experiencing Loss Of Signal. Bellcore Document TA-NWT-000253 Section 6.3.1.1.1 states that... A SONET NE shall declare a LOS failure when the LOS defect persists for 2.5 (+- .5) seconds, or when a LOS defect is present and the criteria for LOF failure declaration have been met. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.36 |
asxSonetLOSClearedThis trap indicates that the LOS condition identified by trap asxSonetLOSDetected has been cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.37 |
asxSonetPathLabelDetectedThis trap indicates that the specified SONET port is receiving and errored C2 Path Label byte. Reference Bellcore Document TA-NWT-000253 Section 3.3.2.3 and 6.3.1.1.8 the Path Label (C2) byte should have the value 0x13 or 0x01. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.38 |
asxSonetPathLabelClearedThis trap indicates that the Errored Path Label (C2) byte error condition signaled by the asxSonetPathLabelDetected trap has been cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.39 |
asxSonetLineAISDetectedThis trap indicates that the specified SONET port is receiving a Line level Alarm Indication Signal from the far-end equipment. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.40 |
asxSonetLineAISClearedThis trap indicates that the Line AIS error condition signaled by the asxSonetLineAISDetected trap has been cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.41 |
asxDS3PLCPYellowDetectedThis trap indicates that the specified DS3 port has detected incoming PLCP Yellow Alarm. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.46 |
asxDS3PLCPYellowClearedThis trap indicates that the specified DS3 port has detected clearance of incoming PLCP Yellow Alarm. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.47 |
asxDS3PLCPLOFDetectedThis trap indicates that the specified DS3 port has detected incoming PLCP LOF Alarm. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.48 |
asxDS3PLCPLOFClearedThis trap indicates that the specified DS3 port has detected clearance of incoming PLCP LOF Alarm. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.49 |
asxDS3LOFDetectedThis trap indicates that Loss Of Frame(LOF) is detected on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.50 |
asxDS3LOFClearedThis trap indicates that Loss Of Frame is cleared on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.51 |
asxDS3AISDetectedThis trap indicates that AIS Alarm is detected on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.52 |
asxDS3AISClearedThis trap indicates that AIS Alarm is cleared on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.53 |
asxDS1PLCPYellowDetectedThis trap indicates that the specified DS1 port has detected incoming PLCP Yellow Alarm. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.60 |
asxDS1PLCPYellowClearedThis trap indicates that the specified DS1 port has detected clearance of incoming PLCP Yellow Alarm. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.61 |
asxDS1PLCPLOFDetectedThis trap indicates that the specified DS1 port has detected incoming PLCP LOF Alarm. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.62 |
asxDS1PLCPLOFClearedThis trap indicates that the specified DS1 port has detected clearance of incoming PLCP LOF Alarm. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.63 |
asxDS1YellowDetectedThis trap indicates that Yellow Alarm is detected on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.64 |
asxDS1YellowClearedThis trap indicates that Yellow Alarm is cleared on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.65 |
asxDS1AISDetectedThis trap indicates that AIS Alarm is detected on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.66 |
asxDS1AISClearedThis trap indicates that AIS Alarm is cleared on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.67 |
asxDS1LOSDetectedThis trap indicates that LOS Alarm is detected on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.68 |
asxDS1LOSClearedThis trap indicates that LOS Alarm is cleared on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.69 |
asxDS1LOFDetectedThis trap indicates that LOF Alarm is detected on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.70 |
asxDS1LOFClearedThis trap indicates that LOF Alarm is cleared on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.71 |
asxDS3FERFDetectedThis trap indicates that FERF Alarm or DS3 Yellow Alarm is detected on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.74 |
asxDS3FERFClearedThis trap indicates that FERF Alarm or DS3 Yellow Alarm is cleared on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.75 |
asxE3YellowDetectedThis trap indicates that the Yellow Alarm is being detected on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.78 |
asxE3YellowClearedThis trap indicates that Yellow alarm has cleared on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.79 |
asxE3OOFDetectedThis trap indicates that Out Of Frame (OOF) is detected on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.80 |
asxE3OOFClearedThis trap indicates that Loss Of Frame is cleared on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.81 |
asxE3AtmLCDDetectedThis trap indicates that the specified E3 port is experiencing Loss of Cell Deliniation (LCD). A LCD failure is declared when the LCD defect persists for a period of 2.5 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.82 |
asxE3AtmLCDClearedThis trap indicates that the LCD failure identified by trap asxE3AtmLCDDetected has been cleared. A LCD failure is cleared when the LCD defect is absent for 10 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.83 |
asxE3PLCPYellowDetectedThis trap indicates that the specified E3 port has detected incoming PLCP Yellow Alarm. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.86 |
asxE3PLCPYellowClearedThis trap indicates that the specified E3 port has detected clearance of incoming PLCP Yellow Alarm. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.87 |
asxE1YellowDetectedThis trap indicates that the Yellow Alarm is being detected on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.90 |
asxE1YellowClearedThis trap indicates that Yellow alarm has cleared on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.91 |
asxE1LOFDetectedThis trap indicates that LOF is being detected on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.92 |
asxE1LOFClearedThis trap indicates that LOF is cleared on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.93 |
asxE1PLCPYellowDetectedThis trap indicates that the specified E1 port has detected incoming PLCP Yellow Alarm. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.96 |
asxE1PLCPYellowClearedThis trap indicates that the specified E1 port has detected clearance of incoming PLCP Yellow Alarm. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.97 |
asxE1PLCPLOFDetectedThis trap indicates that the specified E1 port has detected incoming PLCP LOF Alarm. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.98 |
asxE1PLCPLOFClearedThis trap indicates that incoming PLCP LOF alarm has been cleared on the specified E1 port. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.99 |
asxE1LOSDetectedThis trap indicates that the specified E1 port has detected incoming LOS Alarm. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.100 |
asxE1LOSClearedThis trap indicates that incoming LOS alarm has been cleared on the specified E1 port. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.101 |
asxE1AISDetectedThis trap indicates that the specified E1 port has detected incoming AIS Alarm. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.102 |
asxE1AISClearedThis trap indicates that incoming AIS alarm has been cleared on the specified E1 port. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.103 |
asxE3AISDetectedThis trap indicates that the specified E3 port has detected incoming AIS Alarm. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.104 |
asxE3AISClearedThis trap indicates that incoming AIS alarm has been cleared on the specified E3 port. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.105 |
asxE3LOSDetectedThis trap indicates that the specified E3 port has detected incoming LOS Alarm. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.106 |
asxE3LOSClearedThis trap indicates that incoming LOS alarm has been cleared on the specified E3 port. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.107 |
asxE3PLCPLOFDetectedThis trap indicates that the specified E3 port has detected incoming PLCP LOF Alarm. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.108 |
asxE3PLCPLOFClearedThis trap indicates that incoming PLCP LOF alarm has been cleared on the specified E3 port. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.109 |
asxJ2YellowDetectedThis trap indicates that Yellow Alarm is detected on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.112 |
asxJ2YellowClearedThis trap indicates that Yellow Alarm is cleared on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.113 |
asxJ2AISDetectedThis trap indicates that AIS Alarm is detected on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.114 |
asxJ2AISClearedThis trap indicates that AIS Alarm is cleared on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.115 |
asxJ2LOSDetectedThis trap indicates that LOS Alarm is detected on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.116 |
asxJ2LOSClearedThis trap indicates that LOS Alarm is cleared on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.117 |
asxJ2LOFDetectedThis trap indicates that LOF Alarm is detected on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.118 |
asxJ2LOFClearedThis trap indicates that LOF Alarm is cleared on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.119 |
asxDS3LOSDetectedThis trap indicates that the specified DS3 port has detected incoming LOS Alarm. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.120 |
asxDS3LOSClearedThis trap indicates that the incoming LOS Alarm has been cleared on the specified DS3 port. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.121 |
asxSonetLOFDetectedThis trap indicates that the specified SONET port is experiencing Loss Of Frame (LOF) failure. An LOF failure is declared when the LOF defect persists fore a period of 2.5 +/- 0.5 seconds, except when an LOS defect or failure is present. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.130 |
asxSonetLOFClearedThis trap indicates that the LOF failure identified by trap asxSonetLOFDetected has been cleared. The LOF failure is cleared when the LOS failure is declared, or when the LOF defect is absent for 10 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.131 |
asxSonetLineRDIDetectedThis trap indicates that the specified SONET port is experiencing Line Remote Defect Indication (LRDI). A Line RDI failure is declared when the incoming Line RDI defects lasts for 2.5 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.132 |
asxSonetLineRDIClearedThis trap indicates that the Line RDI failure identified by trap asxSonetLineRDIDetected has been cleared. The Line RDI failure is cleared when no Line RDI defects are detected for 10 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.133 |
asxSonetPathAISDetectedThis trap indicates that the specified SONET port is experiencing Path Alarm Inidication Signal (PAIS). A Path AIS failure is declared when the Path AIS defect persists for 2.5 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.134 |
asxSonetPathAISClearedThis trap indicates that the PathAIS failure identified by trap asxSonetPathAISDetected has been cleared. A PAIS failure is cleared when the PAIS defect is absent for 10 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.135 |
asxSonetPathLOPDetectedThis trap indicates that the specified SONET port is experiencing Loss Of Pointer (LOP). A LOP failure is declared when the LOP defect persists for a period of 2.5 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.136 |
asxSonetPathLOPClearedThis trap indicates that the LOP failure identified by trap asxSonetLOPDetected has been cleared. A LOP failure is cleared when the LOP defect is absent for 10 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.137 |
asxSonetPathUNEQDetectedThis trap indicates that the specified SONET port is experiencing unequiped (UNEQ). A UNEQ failure is declared when the UNEQ defect persists for a period of 2.5 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.138 |
asxSonetPathUNEQClearedThis trap indicates that the UNEQ failure identified by trap asxSonetUNEQDetected has been cleared. A UNEQ failure is cleared when the UNEQ defect is absent for 10 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.139 |
asxSonetPathRDIDetectedThis trap indicates that the specified SONET port is experiencing Path Remote Defect Indication (PRDI). A Path RDI failure is declared when the incoming Path RDI defects lasts for 2.5 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.140 |
asxSonetPathRDIClearedThis trap indicates that the Path RDI failure identified by trap asxSonetPathRDIDetected has been cleared. The Path RDI failure is cleared when no Path RDI defects are detected for 10 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.141 |
asxSonetAtmLCDDetectedThis trap indicates that the specified SONET port is experiencing Loss of Cell Deliniation (LCD). A LCD failure is declared when the LCD defect persists for a period of 2.5 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.142 |
asxSonetAtmLCDClearedThis trap indicates that the LCD failure identified by trap asxSonetAtmLCDDetected has been cleared. A LCD failure is cleared when the LCD defect is absent for 10 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.143 |
asxSonetAtmLineBIPDetectedThis trap indicates that the specified SONET port is experiencing Bit Interleaved Parity (BIP) errors. A Line BIP failure is declared when the Line BIP defect persists for a period of 2.5 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.144 |
asxSonetAtmLineBIPClearedThis trap indicates that the Line BIP failure identified by trap asxSonetAtmLineBIPDetected has been cleared. A Line BIP failure is cleared when the Line BIP defect is absent for 10 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.145 |
asxDS3IdleDetectedThis trap indicates that an Idle Maintenance Signal (IDLE) is detected on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.160 |
asxDS3IdleClearedThis trap indicates that an Idle Maintenance Signal (IDLE) is cleared on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.161 |
asxDS3AtmLCDDetectedThis trap indicates that the specified DS3 port is experiencing Loss of Cell Deliniation (LCD). A LCD failure is declared when the LCD defect persists for a period of 2.5 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.162 |
asxDS3AtmLCDClearedThis trap indicates that the LCD failure identified by trap asxDS3AtmLCDDetected has been cleared. A LCD failure is cleared when the LCD defect is absent for 10 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.163 |
asxDS3PbitPerrDetectedThis trap indicates that the specified DS3 port is experiencing P-bit Parity errors. A P-bit Parity Error failure is declared when the P-bit Parity Error persists for a period of 2.5 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.164 |
asxDS3PbitPerrClearedThis trap indicates that the P-bit Parity Error failure identified by trap asxDS3PbitPerrDetected has been cleared. A P-bit Parity Error failure is cleared when the P-bit Parity Error defect is absent for 10 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.165 |
asxDS1PRBSDetectedThis trap indicates that PRBS pattern is detected on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.176 |
asxDS1PRBSClearedThis trap indicates that PRBS pattern is cleared on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.177 |
asxDS1AtmLCDDetectedThis trap indicates that the specified DS1 port is experiencing Loss of Cell Deliniation (LCD). A LCD failure is declared when the LCD defect persists for a period of 2.5 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.178 |
asxDS1AtmLCDClearedThis trap indicates that the LCD failure identified by trap asxDS1AtmLCDDetected has been cleared. A LCD failure is cleared when the LCD defect is absent for 10 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.179 |
asxDS1CRCErrDetectedThis trap indicates that the specified DS1 port is experiencing excessive CRC-6 errors. A CRC-6 Error failure is declared when the CRC-6 Error persists for a period of 2.5 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.180 |
asxDS1CRCErrClearedThis trap indicates that the excessive CRC-6 Error failure identified by trap asxDS1CRCErrDetected has been cleared. A CRC-6 Parity Error failure is cleared when the CRC-6 Error defect is absent for 10 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.181 |
asxE3TrailChangeDetectedThis trap indicates that a change in the trail trace message was detected on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.192 |
asxE1AtmLCDDetectedThis trap indicates that the specified E1 port is experiencing Loss of Cell Deliniation (LCD). A LCD failure is declared when the LCD defect persists for a period of 2.5 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.208 |
asxE1AtmLCDClearedThis trap indicates that the LCD failure identified by trap asxE1AtmLCDDetected has been cleared. A LCD failure is cleared when the LCD defect is absent for 10 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.209 |
asxJ2RLOCDetectedThis trap indicates that Receive Loss of Clock (RLOC) is detected on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.224 |
asxJ2RLOCClearedThis trap indicates that Receive Loss of Clock (RLOC) is cleared on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.225 |
asxJ2HBERDetectedThis trap indicates that High Bit Error Rate (HBER) is detected on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.226 |
asxJ2HBERClearedThis trap indicates that High Bit Error Rate (HBER) is cleared on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.227 |
asxJ2PAISDetectedThis trap indicates that Payload Alarm Indication Signal (PAIS) is detected on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.228 |
asxJ2PAISClearedThis trap indicates that Payload Alarm Indication SIgnal (PAIS) is cleared on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.229 |
asxJ2AtmLCDDetectedThis trap indicates that the specified J2 port is experiencing Loss of Cell Deliniation (LCD). A LCD failure is declared when the LCD defect persists for a period of 2.5 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.230 |
asxJ2AtmLCDClearedThis trap indicates that the LCD failure identified by trap asxJ2AtmLCDDetected has been cleared. A LCD failure is cleared when the LCD defect is absent for 10 +/- 0.5 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.231 |
asxJ2TLOCDetectedThis trap indicates that Transmit Loss of Clock (TLOC) is detected. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.232 |
asxJ2TLOCClearedThis trap indicates that Transmit Loss of Clock (TLOC) is cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.233 |
asxTP25LOSDetectedThis trap indicates that LOS Alarm is detected on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.250 |
asxTP25LOSClearedThis trap indicates that LOS Alarm is cleared on the incoming signal. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.251 |
asxOutputQueueCongestedThis trap indicates that the output queue for the given priority has exceeded its dedicated length, and has begun overflowing into the shared buffer space on the netmod. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1024 |
asxOutputQueueCellLossThis trap indicates that the output queue for the given priority has overflowed and cells have been dropped. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1025 |
asxExtendedModeViolationThis trap indicates that a series A or B network module was inserted into a switch board running in extended mode. Multicast will not work on the series B module without removing all series D modules and rebooting the rebooted. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1026 |
asxNonextendedModeWarningThis trap indicates that a series C or greater network module was inserted into a switch board running in non-extended mode. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1027 |
crConfMemoryOflowThis trap is generated when the allocated callrecord memory(as indicated by crMemoryAllocated) is exceeded. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1029 |
crXfrPrimaryXfrFailedThis trap is generated when the call record transfer to the primary host(as indicated by crXfrPrimaryUrl) fails. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1030 |
crXfrSecondaryXfrFailedThis trap is generated when the call record transfer to the secondary host(as indicated by crXfrSecondaryUrl) fails. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1031 |
crConfMemAllocFailThis trap is generated when Callrecord functionality is unable to allocate memory as specified by crMemoryAllocated. This can happen when the crConfAdminStatus changes state from `off' or when the switch reboots when Callrecords is configured `on'. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1032 |
crGeneralFailureThis trap is generated when any of the callrecord related functionality fails for any reason. One example would be when the Callrecord Module fails to schedule an interval timer. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1033 |
asxDualScpSyncFailureThis trap indicates that automatic CDB synchronization is disabled due to failures. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1034 |
asxDualScpSwitchOverThis trap indicates that the backup SCP has taken control of the switch. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1035 |
asxDualScpHotSwapThis trap indicates that an SCP hotswap insertion or removal has occurred. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1036 |
asxVPAISDetectedThis trap indicates that the Alarm Indication Signal (AIS) is detected on the incoming (terminating) virtual path. This trap is generated once when the virtual path is declared to be in the active AIS state. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1037 |
asxVPAISClearedThis trap indicates that the Alarm Indication Signal (AIS) has been removed from the incoming (terminating) virtual path. This trap is generated once when the virtual path is declared to be in the inactive AIS state. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1038 |
asxVPRDIDetectedThis trap indicates that the Remote Defect Indication (RDI) is detected on the incoming (terminating) virtual path. This trap is generated once when the virtual path is declared to be in the active RDI state. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1039 |
asxVPRDIClearedThis trap indicates that the Remote Defect Indication (RDI) has been removed from the incoming (terminating) virtual path. This trap is generated once when the virtual path is declared to be in the inactive RDI state. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1040 |
asxNonextendedModeViolationThis trap indicates that a series D network module was inserted into a switch board running in non-extended mode. Multicast will not work on the series D module without removing all series B modules and rebooting the switch. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1041 |
asxUnsupportedNetworkModuleThis trap indicates that a unsupported network module was inserted into a switch. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1042 |
asxDualScpRedundancyThis trap indicates that there is a change in the state of dual SCP Redundancy. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1043 |
asxIpFilterViolationAn asxIpFilterViolation trap occurs when an incoming IP packet is unauthorized to enter the switch control port and has been dropped. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1049 |
q2931AFRejectKnownThis trap is generated whenever any q2931 UNI with Address Filtering enabled rejects a Setup request because the request matched a template with the action 'reject'. The variables sent in the trap identify the source and destination UNI for the call. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1053 |
q2931AFRejectUnknownThis trap is generated whenever any q2931 UNI with Address Filtering enabled rejects a Setup request because the address matched no template. The variables sent in the trap identify the source and destination UNI for the call. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1054 |
q2931CreationFailureThis trap is generated whenever a switch fails to create a UNI. This is most likely due to a resource limitation on the switch. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1061 |
asxPsCurrentDownThis trap alerts that one ATM switch power supply had a curent failure. The power supply that failed is identified by the power supply index. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1068 |
asxPsCurrentUpThis trap alerts that one ATM switch power supply that had a curent failure is now up. The power supply that is back up is identified by the power supply index. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1069 |
asxPs5VoltDownThis trap alerts that one ATM switch power supply had a +5V failure. The power supply that failed is identified by the power supply index. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1070 |
asxPs5VoltUpThis trap alerts that one ATM switch power supply that had a +5V failure is now up. The power supply that is back up is identified by the power supply index. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1071 |
asxSwitchLoginDetectedAn asxSwitchLoginDetected trap signifies that a user logged in on the switch. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1072 |
asxSwitchLoginFailedAn asxSwitchLoginFailed trap signifies that a user's attempt to log in on the switch failed. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1073 |
pnniTdbGuardbandResrvFailThis trap is generated when guardband memory reserve for any of the PNNI TDB(Topology Database) related functionalites like creation,modification and deletion on objects like node, ptse,flags,interal prefixes,external prefixes and etc fails. The switch is low on memory. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1074 |
pnniTdbInconsistentStateThis trap is generated when PNNI TDB(Topology Database) is in an unrecoverable error condition due to MALLOC and other TDB related faliures. When this happenes the associated logical node is shutdown and this trap is sent.The switch has to be rebooted to bring this PNNI logical node up again. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1075 |
asxShmem2OutputQueueCongestedThis trap indicates that the output queue for the given priority has exceeded its dedicated length, and has begun overflowing into the shared buffer space on the netmod. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1077 |
asxShmem2OutputQueueCellLossThis trap indicates that the output queue for the given priority has overflowed and cells have been dropped. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1078 |
fabricLvl3LookupThis trap is generated when a fabric detects excessive level 3 lookup errors. The level 3 lookup count is read every second. If the lookup count is non-null for 5 consecutive seconds, then this trap is generated. If the errors continue, this trap will be generated continuously every 5 seconds. This trap can be caused by: a misconfigured PVC; bad hardware. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1080 |
fabricCorrectedLookupThis trap is generated when the SCP detects inconsistant information in the HDCOMP lookup. The switch has corrected the bad information in the HDCOMP lookup ASIC's data structures. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1081 |
spvcRerouteInitiatedThis trap is sent when a SPVC is being re-routed due to a better path being found. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1090 |
asxQ2931DownThis trap is generated whenever UNI signalling goes down. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1091 |
asxQ2931UpThis trap is generated whenever UNI signalling goes up. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1092 |
asxFabricDownAn asxFabricDown trap signifies that the sending protocol entity recognizes a failure in one of the ATM Switch fabric, that is identified by the board number. This is probably caused by a hot-swap of a fabric module. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1093 |
asxFabricUpAn asxFabricUp trap signifies that the sending protocol entity recognizes a new operational ATM Switch fabric, that is identified by the board number. This is probably caused by a hot-swap of a fabric module. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1094 |
asxQ2931CallClearingThis trap is generated whenever calls are cleared in a signalling interface for the following reasons. * Carrier loss * SONET alarms in case of SONE * VP failure NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.1095 |
pnniSpvccDownThis trap is sent when a SPVC call is cleared or deleted. The pnniSpvcSrcDownReason indicates if the call was cleared due to a better route being found or a network failure. It also may indicate SPVC deletion. This trap is only sent if pnniSpvcTrapMode is all. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.2004 |
pnniSpvccUpThis trap is send when a SPVC call is established. It identifies the SPVC and the old and new cost. If the call has not been up before, the pnniSpvcSrcOldRouteCost will be -1. This trap is only sent if pnniSpvcTrapMode is failure or all. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.2005 |
pnniSpvccFailThis trap is sent when a SPVC call that is down fails to get connected on 16 consecutive attempts. This trap is only sent if pnniSpvcTrapMode is failure or all. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.2006 |
pnniSpvpcDownThis trap is sent when a SPVP call is cleared. The pnniSpvcSrcDownReason indicates if the call was cleared due to a better route being found or a network failure. It also may indicate SPVPC deletion. This trap is only sent if pnniSpvpcTrapMode is all. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.2007 |
pnniSpvpcUpThis trap is send when a SPVP call is established. It identifies the SPVP and the old and new cost. If the call has not been up before, the pnniSpvcSrcOldRouteCost will be -1. This trap is only sent if pnniSpvpcTrapMode is all or failure. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.2008 |
pnniSpvpcFailThis trap is sent when a SPVP call that is down fails to get connected on 16 consecutive attempts. This trap is only sent if pnniSpvpcTrapMode is all or failure. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.2009 |
asxPortCardDownAn asxPortCardDown trap signifies that the sending protocol entity recognizes a failure in one of the ATM Switch portcards, that is identified by the portcard name. This is probably caused by a hot-swap of the port card. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.2010 |
asxPortCardUpAn asxPortCardUp trap signifies that the sending protocol entity recognizes a new operational ATM Switch port card, that is identified by the portcard name. This is probably caused by a hot-swap of the port card. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.2011 |
asxServiceCategoryOutputQueueCongestedThis trap indicates that the output queue for the service category has exceeded its dedicated length, and has begun overflowing into the shared buffer space on the netmod. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.2013 |
asxServiceCategoryOutputQueueCellLossThis trap indicates that the output queue for the given service category has overflowed and cells have been dropped. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.2014 |
pnniNormalToOverloadTransitionThis trap is generated on transition from the normal state to the overload state. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.2015 |
pnniOverloadToNormalTransitionThis trap is generated on transition from the overload to the normal state. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.2016 |
pnniPmpRerouteInitiatedThis trap is sent when a party is being re-routed due to a better path being found or if a reroute is requested using a AMI command. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.2020 |
pnniPmpSpvcUpThis trap is send when a pmp SPVC call is established. This trap is only sent if pnniSpvcTrapMode is failure or all. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.2021 |
pnniPmpSpvcDownThis trap is sent when a pmp SPVC call is cleared. The pnniSpvcSrcDownReason indicates if the call was cleared due to a better route being found or a network failure. This trap is only sent if pnniSpvpcTrapMode is all. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.2022 |
pnniPmpSpvcFailThis trap is sent when a SPVC call that is down fails to get connected on 16 consecutive attempts. This trap is only sent if pnniSpvcTrapMode is failure or all. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.2023 |
pnniSpvxRGroupSwoverThis trap is sent when a automatic switch over occurs in a SPVC Redundancy group that has automatic PVC switch over enabled. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.2024 |
asxSVXCPStateTransferFailedThis trap is sent when the SVx/SPVx Preservation module is unable to transfer call and interface state information to the Standby SCP, due either to temporary unavailablility of system resources or to a permanent system error requiring a system reboot. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.2025 |
asxSVXCPStateTransferRestartedThis trap is sent when the SVx/SPVx Preservation module has restarted its transfer of call and interface state information to the Standby SCP, which transfer was halted due to unavailablility of system resources. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.2026 |
asxSVXCPStateDroppedCallThis trap is sent when the SVx/SPVx Preservation module has insufficient memory to store one or more calls during its transfer of call and interface state information to the Standby SCP. Such calls therefore will be lost (not preserved on switchover). This trap is sent only once, no matter how many calls suffer this fate. Recovering any lost calls is possible only by disabling and then re-enabling SVx/SPVx Preservation, in order to provoke a complete retrial of the transfer process. NOTIFICATION-TYPE .1.3.6.1.4.1.326.2.2.0.2027 |
boardGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.1.1 |
boardTableA table of ATM switch board information. SEQUENCE OF BoardEntry .1.3.6.1.4.1.326.2.2.1.1.1.1 |
boardEntryA table entry containing ATM switch board information. BoardEntry .1.3.6.1.4.1.326.2.2.1.1.1.1.1 |
boardIndexThe index of this board within the ATM switch.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.1.1.1 |
boardVersionThe ATM switch board version number in hex. The version number 0x1 is revision A, 0x2 is revision B etc. Version number 0x0 represents an unknown type.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.1.1.2 |
boardModelThe ATM switch board model number.ro Enumeration .1.3.6.1.4.1.326.2.2.1.1.1.1.1.3 |
boardSerialNumberThe ATM switch board serial number.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.1.1.4 |
numberOfModulesThe number of network modules on this ATM switch board.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.1.1.5 |
vpiLookupErrorsThe number of VPI lookup errors.roobsolete Counter32 .1.3.6.1.4.1.326.2.2.1.1.1.1.1.6 |
vciLookupErrorsThe number of VCI lookup errors.roobsolete Counter32 .1.3.6.1.4.1.326.2.2.1.1.1.1.1.7 |
boardControlPortThis object identifies the index for the control port on this switch board.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.1.1.8 |
boardHDCOMPAsicVersionThis object identifies the version number of the HDCOMP ASIC on this switch board.roobsolete Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.1.1.9 |
boardMcastSpaceIndexThis object is the index into mcastSpaceTable that gives the number of multicast connections currently supported on this board. Changing this value has the effect of changing the number of multicast connections supported. Change will be effective after reboot only.rw Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.1.1.10 |
numberOfBoardsThe number of switch boards on this ATM switch.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.2 |
utilization OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.1.1.3 |
procUtilGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.1.1.3.1 |
procUtilLastUpdateThe time the procUtilValue was last updatedro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.326.2.2.1.1.1.3.1.1 |
procUtilValueThe percentage of the processor power that has been used over the last monitoring intervalro Gauge32 .1.3.6.1.4.1.326.2.2.1.1.1.3.1.2 |
procUtilMonIntervalThe amount of time between calculations of the procUtilValue. This value is expressed in units of 10 msec, (100 per sec). This value may take the value of 1 to 60 secondsrw INTEGER .1.3.6.1.4.1.326.2.2.1.1.1.3.1.3 |
procUtilMinLoadThe MIN percentage of the processor power that has been. This value can be reset by setting the field procUtilHistoryReset.ro Gauge32 .1.3.6.1.4.1.326.2.2.1.1.1.3.1.4 |
procUtilMinLoadLastUpdateThe time the procUtilMinLoad was last updatedro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.326.2.2.1.1.1.3.1.5 |
procUtilMaxLoadThe MAX percentage of the processor power that has been. This value can be reset by setting the field procUtilHistoryReset.ro Gauge32 .1.3.6.1.4.1.326.2.2.1.1.1.3.1.6 |
procUtilMaxLoadLastUpdateThe time the procUtilMaxLoad was last updatedro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.326.2.2.1.1.1.3.1.7 |
procUtilHistoryResetThis is in effect a WRITE_ONLY field. Setting this field resets the procUtilMinLoad, procUtilMinLoadLastUpdate, procUtilMaxLoad, and procUtilMaxLoadLastUpdate. This field can be set to anything by the NMS. When this field is read, it will always report NULL.rw INTEGER (0) .1.3.6.1.4.1.326.2.2.1.1.1.3.1.8 |
procUtilsNumMallocPartThe number of malloc partitions used on this SCP.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.1.9 |
procUtilsSystemPartitionIDThe partition ID os the system MALLOC pool. Use this value as an ID into the mallocUtilTable to view the system malloc pool statisticsro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.1.10 |
mallocUtilTableA table containing malloc statistics for each memory partition SEQUENCE OF MallocUtilEntry .1.3.6.1.4.1.326.2.2.1.1.1.3.2 |
mallocUtilEntryA table containing malloc statistics for each memory partition MallocUtilEntry .1.3.6.1.4.1.326.2.2.1.1.1.3.2.1 |
mallocPartIdThe partition number for this malloc partition. The switch has a default partition named (procUtilsSystemPartitionID). Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.2.1.1 |
numBytesFreeNumber of Free Bytes in this partitionro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.2.1.2 |
numBlocksFreeThe number of free blocks in this partitionro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.2.1.3 |
maxBlockSizeFreeThe max block size that is freero Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.2.1.4 |
numBytesAllocNumber of allocated bytes in this partitionro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.2.1.5 |
numBlocksAllocThe number of allocated blocks in this partitonro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.2.1.6 |
mbufUtilGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.1.1.3.3 |
mbufsCountmbufs obtained from page poolro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.3.1 |
mbufsClustersclusters obtained from page poolro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.3.2 |
mbufsSpaceinterface pages obtained from page poolro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.3.3 |
mbufsClFreeFree Clustersro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.3.4 |
mbufsDropsTimes failed to find spacero Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.3.5 |
mbufsWaitTimes waited for spacero Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.3.6 |
mbufsDrainTimes drained protocols for spacero Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.3.7 |
mbufsFreeAlloc# of mbufs allocated to free listro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.3.8 |
mbufsDataFreeAlloc# of mbufs allocated to dynamic (data) allocationro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.3.9 |
mbufsHeaderAlloc# of mbufs allocated to packet headersro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.3.10 |
mbufsSocketAlloc# of mbufs allocated to socket structuresro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.3.11 |
mbufsPcbAlloc# of mbufs allocated to protocol control blocksro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.3.12 |
mbufsRtableAlloc# of mbufs allocated to routing tablesro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.3.13 |
mbufsHtableAlloc# of mbufs allocated to IMP Host Tablesro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.3.14 |
mbufsAtableAlloc# of mbufs allocated to Address Resolution Tablesro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.3.15 |
mbufsSoNameAlloc# of mbufs allocated to Socket Namero Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.3.16 |
mbufsZombieAlloc# of mbufs allocated to Zombie Processesro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.3.17 |
mbufsSoOptsAlloc# of mbufs allocated to Socket Optionsro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.3.18 |
mbufsFtableAlloc# of mbufs allocated to Fragment Re-assembly Headersro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.3.19 |
mbufsRightsAlloc# of mbufs allocated to Access Rightsro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.3.20 |
mbufsIFaddrAlloc# of mbufs allocated to Interface Addressesro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.3.3.21 |
boardStatsTableA table of ATM switch fabric statistics information. SEQUENCE OF BoardStatsEntry .1.3.6.1.4.1.326.2.2.1.1.1.4 |
boardStatsEntryA table entry containing ATM switch fabric statistics information. BoardStatsEntry .1.3.6.1.4.1.326.2.2.1.1.1.4.1 |
boardStatsBoardThe index of this fabric within the ATM switch. Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.4.1.1 |
boardStatsIndexThe index of this statistics within the ATM switch fabric. Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.4.1.2 |
boardStatsNameThe name of this statistics within the ATM switch fabric.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.1.1.4.1.3 |
boardStatsValueThe value of this statistics within the ATM switch fabric.ro Gauge32 .1.3.6.1.4.1.326.2.2.1.1.1.4.1.4 |
portCardGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.1.1.5 |
portCardTableA table of ATM switch port card information. SEQUENCE OF PortCardEntry .1.3.6.1.4.1.326.2.2.1.1.1.5.1 |
portCardEntryA table entry containing ATM switch port card information. PortCardEntry .1.3.6.1.4.1.326.2.2.1.1.1.5.1.1 |
portCardIndexThe unique index of this port card within the ATM switch. Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.5.1.1.1 |
portCardNameThe name of this port card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.1.1.5.1.1.2 |
portCardFlavorThe flavor of this port card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.1.1.5.1.1.3 |
portCardTypeThe type description of this port card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.1.1.5.1.1.4 |
portCardUptimeThe length of time this port card has been up in hundredths of a second.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.326.2.2.1.1.1.5.1.1.5 |
portCardSerialNumberThe serial number of this port card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.1.1.5.1.1.6 |
portCardAssemblyRevisionThe assembly revision number of this port card.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.5.1.1.7 |
portCardHardwareConfThe hardware configuration number of this port card.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.5.1.1.8 |
portCardStateThe desired state of this port card. If set to reset(1), the port card is reset. Normally, when the port card is active, it is inService(2).rw Enumeration .1.3.6.1.4.1.326.2.2.1.1.1.5.1.1.9 |
boardTrafficManagementGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.1.1.6 |
boardTrafficManagementPerPriorityTableA table of ATM switch fabric traffic management features that can be controlled per fabric and per priority. SEQUENCE OF BoardTrafficManagementPerPriorityEntry .1.3.6.1.4.1.326.2.2.1.1.1.6.1 |
boardTrafficManagementPerPriorityEntryA table entry of ATM switch fabric traffic management features that can be controlled per fabric and per priority. BoardTrafficManagementPerPriorityEntry .1.3.6.1.4.1.326.2.2.1.1.1.6.1.1 |
btmPerPriorityBoardThe index of the fabric. Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.6.1.1.1 |
btmPerPriorityPriorityThe index of the traffic priority. Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.6.1.1.2 |
btmPerPriorityFeatureThe index of the feature. Feature 1 is EPD Threshold. Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.6.1.1.3 |
btmPerPriorityPriorityNameThe name of the traffic priority (e.g. CBR or UBR).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.1.1.6.1.1.4 |
btmPerPriorityValueThe value of the specified feature for the specified priority.rw Integer32 .1.3.6.1.4.1.326.2.2.1.1.1.6.1.1.5 |
moduleGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.1.2 |
moduleTableA table of network module information. SEQUENCE OF ModuleEntry .1.3.6.1.4.1.326.2.2.1.1.2.1 |
moduleEntryA table entry containing network module information. ModuleEntry .1.3.6.1.4.1.326.2.2.1.1.2.1.1 |
moduleBoardThe index of this board within the ATM switch.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.2.1.1.1 |
moduleNumberThe number of this network module within the ATM switch.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.2.1.1.2 |
moduleNameThe type name of this network module within the ATM switch.ro DisplayString .1.3.6.1.4.1.326.2.2.1.1.2.1.1.3 |
moduleSpeedThe speed of this network module within the ATM switch.ro Unsigned32 .1.3.6.1.4.1.326.2.2.1.1.2.1.1.4 |
moduleNumberOfPortsThe number of ports on this network module.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.2.1.1.5 |
moduleUptimeThe length of time this network module has been up, in hundredths of a second.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.326.2.2.1.1.2.1.1.6 |
moduleHwMajorRevThe hardware major revision number of the network module. For generationD network modules this revision number is an ascii character value.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.2.1.1.7 |
moduleHwMinorRevThe hardware minor revision number of the network module.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.2.1.1.8 |
moduleVersionThe hardware version of this network module.ro Enumeration .1.3.6.1.4.1.326.2.2.1.1.2.1.1.9 |
moduleTimingSupportDoes this network module support distributed timing?ro Enumeration .1.3.6.1.4.1.326.2.2.1.1.2.1.1.10 |
moduleProductNumberThe product number of this network module.ro DisplayString .1.3.6.1.4.1.326.2.2.1.1.2.1.1.11 |
moduleStateThe desired state of this network module. If set to reset(1), the netmod is reset. Normally, when the netmod is active, it is inService(2). To put a netmod out of service, this entry must be set to outOfService(3).rw Enumeration .1.3.6.1.4.1.326.2.2.1.1.2.1.1.12 |
moduleSerialNumberThe string representing the serial number for this network module.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.1.2.1.1.13 |
moduleTestAdminStatusThis variable indicates the hardware test configuration of the network module. It can be set to startTest(2), which starts the hardware tests on the network module. abortTest(3) aborts the test, if the network module is under test. The network module returns to normal(0) after the test ends or is aborted.rw Enumeration .1.3.6.1.4.1.326.2.2.1.1.2.1.1.14 |
moduleTestOperStatusThe status of the hardware tests on the network module. normal (1) indicates that the network module has never undergone hardware tests. The network module is underTest (2), after the test is started on it, and goes to testSuccessful (3) or testFailed (4), after the tests end. If the tests are aborted, the network module goes to testAborted (5) state. Those network modules that do not support hardware tests like Series-C and LC modules, are in testUnsupported (6) state.ro Enumeration .1.3.6.1.4.1.326.2.2.1.1.2.1.1.15 |
moduleTestStatusTextA message describing the status of the current testro DisplayString .1.3.6.1.4.1.326.2.2.1.1.2.1.1.16 |
moduleAttachStateThe actual state of this network module. The netmod state is directed by the moduleState variable. This variable gives the actual state at a given time (which may lag behind the moduleState by several seconds).ro Enumeration .1.3.6.1.4.1.326.2.2.1.1.2.1.1.17 |
moduleCLEIThe Common Language Equipment identifications (CLEI) of this network module.ro DisplayString .1.3.6.1.4.1.326.2.2.1.1.2.1.1.18 |
outputBufferTableA table of output buffer information. SEQUENCE OF OutputBufferEntry .1.3.6.1.4.1.326.2.2.1.1.2.2 |
outputBufferEntryA table entry containing output buffer information. OutputBufferEntry .1.3.6.1.4.1.326.2.2.1.1.2.2.1 |
obufBoardThe index of this output buffer's switch board.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.2.2.1.1 |
obufNumberThe number of the network module for this output buffer.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.2.2.1.2 |
obufTypeThe Priority of this output buffer- 0 is lowest priorityro Integer32 .1.3.6.1.4.1.326.2.2.1.1.2.2.1.3 |
obufOperStatusThe operational status of this output buffer.ro Enumeration .1.3.6.1.4.1.326.2.2.1.1.2.2.1.4 |
obufBufferSizeThe logical size of this output buffer, in cells.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.2.2.1.5 |
obufQueueLengthThe number of cells in this output buffer.ro Gauge32 .1.3.6.1.4.1.326.2.2.1.1.2.2.1.6 |
obufOverflowsThe number of cells dropped because this output buffer was full.ro Gauge32 .1.3.6.1.4.1.326.2.2.1.1.2.2.1.7 |
obufPriorityNameThe priority name (eg. CBR, VBR) for this buffer.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.1.2.2.1.8 |
obufNameThe name (eg. 1, 1A) of this buffer.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.1.2.2.1.9 |
hwPortTableA table of hardware port information. SEQUENCE OF HwPortEntry .1.3.6.1.4.1.326.2.2.1.1.2.3 |
hwPortEntryA table entry containing hardware port information. HwPortEntry .1.3.6.1.4.1.326.2.2.1.1.2.3.1 |
hwPortBoardThe switch board index of this port.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.2.3.1.1 |
hwPortModuleThe network module number of this port.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.2.3.1.2 |
hwPortNumberThe number of this port within its network module.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.2.3.1.3 |
hwPortVersionThe generation of this network module. In general, generation A indicates the most original FORE Systems netmods. Generation-B are intermediate DS3/E3/TAXI. Generation-C are shared-memory based netmods.ro Enumeration .1.3.6.1.4.1.326.2.2.1.1.2.3.1.4 |
hwPortModelThe type of physical connection of this port. The model-ASX(7) indicates this is the control port of the switch. NOTE: as of 2/8/95 the elements model-6port-TAXI-100(6) and model-DS3-PDH(16) should no longer be used. Use the basic types model-TAXI-100(1) and model-DS3(3) to indicate these.ro Enumeration .1.3.6.1.4.1.326.2.2.1.1.2.3.1.5 |
hwPortOperStatusThe operational status of this port. If a port was administered up (by hwPortAdminStatus), but the carrier or the framing bits were lost, the hwPortOperStatus indicates that the port is down(3). Otherwise, the hwPortOperStatus is up(2).ro Enumeration .1.3.6.1.4.1.326.2.2.1.1.2.3.1.6 |
hwPortBufferSizeThe logical size of this port's output buffer, in cells.rodeprecated Integer32 .1.3.6.1.4.1.326.2.2.1.1.2.3.1.7 |
hwPortQueueLengthThe number of cells in this port's output buffer.rodeprecated Gauge32 .1.3.6.1.4.1.326.2.2.1.1.2.3.1.8 |
hwPortOverflowsThe number of seconds in which cells were dropped because this port's output buffer was full.rodeprecated Counter32 .1.3.6.1.4.1.326.2.2.1.1.2.3.1.9 |
hwPortErrorsThe number of seconds in which errored cells were dropped by this port.rodeprecated Counter32 .1.3.6.1.4.1.326.2.2.1.1.2.3.1.10 |
hwPortCarrierThe presence or absence of carrier at this port.ro Enumeration .1.3.6.1.4.1.326.2.2.1.1.2.3.1.11 |
hwPortGlobalIndexThe global index of this port within the ATM switch as a whole. It corresponds to the port number used in the software group of this MIB.rodeprecated Integer32 .1.3.6.1.4.1.326.2.2.1.1.2.3.1.12 |
hwPortNameA textual description of the port indicating the Board Network module and Port (BNP) identifiers. The module is indicated by a letter (A-D), while the board and the port are indicated by numbers.ro DisplayString .1.3.6.1.4.1.326.2.2.1.1.2.3.1.13 |
hwPortAdminStatusThe administrative state of the physical layer of this port. When a port is configured up(1), the physical layer is configured to process all physical layer events including the transmission and reception of data (cells). When a port is configured down(2), the physical layer should be shut down and should ignore all physical layer events (e.g. cell reception, carrier loss, loss of framing, parity errors, etc.). The operational status of a port is reflected in the hwPortOperStatus object.rw Enumeration .1.3.6.1.4.1.326.2.2.1.1.2.3.1.14 |
hwPortTAXILoopbackThis variable represents the loopback status of a TAXI port. For non-TAXI ports (e.g. DS3/E3 or SONET) the loopback configuration should be set in their specific tables.rw Enumeration .1.3.6.1.4.1.326.2.2.1.1.2.3.1.15 |
hwPortLEDModelThe LED model to use for setting the colors of the LEDs on each port. LAN models typically blink the LEDs when data is transmitted or received on the port. WAN models typically keep the LEDs green unless an error condition exists on the port. With SONET netmods the LED models use the following algorithms: LAN (3 states): if (LOS || LOF || AIS_L || LOP_P || UNEQ_P || PLM_P || LCD) { rxLED = RED } else if (RDI_L) { rxLED = YELLOW } else { rxLED = AUTO } txLED = AUTO WAN (3 states): if (LOS || LOF || AIS_L || LOP_P || UNEQ_P || PLM_P || LCD) { rxLED = RED } else if (RDI_L) { rxLED = YELLOW } else { rxLED = GREEN } txLED = GREEN With LAN and WAN models: RED means fault in receive direction, YELLOW means fault in transmit direction (RDI_L defect), AUTO/GREEN means no fault. Only the receive LED color is changed. These models show only three states and do not reflect the status of the AIS_P and RDI_P defects.rw Enumeration .1.3.6.1.4.1.326.2.2.1.1.2.3.1.16 |
hwPortTxLEDIndicates the color of the transmit LED for this port. Auto means that the LED is under hardware control. Typically hardware control means that the LED is normally dark with green blinks to indicate data traffic.ro Enumeration .1.3.6.1.4.1.326.2.2.1.1.2.3.1.17 |
hwPortRxLEDIndicates the color of the receive LED for this port. Auto means that the LED is under hardware control. Typically hardware control means that the LED is normally dark with green blinks to indicate data traffic.ro Enumeration .1.3.6.1.4.1.326.2.2.1.1.2.3.1.18 |
hwPortIfIndexThis entry indicates the IfIndex used to identify this port. It corresponds to the ifIndex used in the rfc2233 rfc1573 ifTablesro Integer32 .1.3.6.1.4.1.326.2.2.1.1.2.3.1.19 |
hwPortRxSyncLEDThe synchronization LED which only applies to the receivers. When green, it indicates that the port is providing the 8 khz clock reference to the switch. This is a new entry which makes sense to those netmod ( currently only FRAM netmod support this LED) which can provide a 8 khz clock reference to the switch. At the netmod scope, only one such LED should be green if the switch is importing a port timing clock.ro Enumeration .1.3.6.1.4.1.326.2.2.1.1.2.3.1.20 |
hwPortCounterResetTimeIndicates when this port's physical interface counters were reset. The TimeStamp is equal to moduleUptime when the reset occurred. If this ports counters were never reset, hwPortCounterResetTime will be zero. This variable is updated whenever hwPortCounterReset or switchCounterReset is written.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.1.2.3.1.21 |
hwPortCounterResetWriting a value of resetRequest will result in a reset of all physical interface counters on this port. VCC indexed counters are excluded. A response value of resetTrue indicates a resetRequest has succeeded and is currently in effect. A response value of resetFalse indicates a reset is not currently in effect.rw Enumeration .1.3.6.1.4.1.326.2.2.1.1.2.3.1.22 |
hwPortSpeedThe speed of this physical port in the ATM switch.ro Unsigned32 .1.3.6.1.4.1.326.2.2.1.1.2.3.1.23 |
netmodAlarmsTableA table of network module alarms information categorized on a per slot basis. SEQUENCE OF NetmodAlarmsEntry .1.3.6.1.4.1.326.2.2.1.1.2.4 |
netmodAlarmsEntryA table entry containing network module alarm information. NetmodAlarmsEntry .1.3.6.1.4.1.326.2.2.1.1.2.4.1 |
netmodSlotThis number represents the unique number of this netmod within the ATM switch. This number starts at 0.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.2.4.1.1 |
netmodSlotPriorityThe priority assigned to this slot. Possible values are High (corresponding to netmodRemovedHighPrio), Low (corresponding to netmodRemovedLowPrio) and None (default)rw Enumeration .1.3.6.1.4.1.326.2.2.1.1.2.4.1.2 |
netmodStatusThe presence/absence of a netmod in this slot is determined by this variable.ro Enumeration .1.3.6.1.4.1.326.2.2.1.1.2.4.1.3 |
netmodNameThe name of this netmod. Example: 1A, 3D for ASX4000 and A, B for pre-ASX4000 switches.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.1.2.4.1.4 |
hdcompTableA table for information about HDCOMPs. SEQUENCE OF HdcompEntry .1.3.6.1.4.1.326.2.2.1.1.2.5 |
hdcompEntryA table for information about HDCOMPs. HdcompEntry .1.3.6.1.4.1.326.2.2.1.1.2.5.1 |
hdcompIndexIndex of the HDCOMP on the switch. Integer32 .1.3.6.1.4.1.326.2.2.1.1.2.5.1.1 |
hdcompDescrDescription of the HDCOMP location on the switch.ro DisplayString .1.3.6.1.4.1.326.2.2.1.1.2.5.1.2 |
hdcompAsicVersionVersion number of the HDCOMP ASIC on the switch.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.2.5.1.3 |
hdcompVpiLookupErrorsThe number of VPI lookup errors.ro Counter32 .1.3.6.1.4.1.326.2.2.1.1.2.5.1.4 |
hdcompVciLookupErrorsThe number of VCI lookup errors.ro Counter32 .1.3.6.1.4.1.326.2.2.1.1.2.5.1.5 |
appModuleTableA table consisting of hardware components that have on-board CPUs. Currently, the FR/ATM, FUNI and IMA network modules appear in this table. SEQUENCE OF AppModuleEntry .1.3.6.1.4.1.326.2.2.1.1.2.6 |
appModuleEntryA table entry containing application module information. AppModuleEntry .1.3.6.1.4.1.326.2.2.1.1.2.6.1 |
appModuleIndexThe index of the application module in this switch.ro Integer32 .1.3.6.1.4.1.326.2.2.1.1.2.6.1.1 |
appModuleNameThe name of this application module.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.1.2.6.1.2 |
appModuleOperStateThe operational state of this network module's hardware.ro Enumeration .1.3.6.1.4.1.326.2.2.1.1.2.6.1.3 |
appModuleStatusTextA text string describing the current state of the hardware.ro DisplayString .1.3.6.1.4.1.326.2.2.1.1.2.6.1.4 |
appModuleApplicationTypeThis variable indicates the application(s) running on this application module.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.1.2.6.1.5 |
appModuleSoftwareVersionVersion of the software running on this application module.ro DisplayString .1.3.6.1.4.1.326.2.2.1.1.2.6.1.6 |
appModuleBootSoftwareVersionVersion of the BOOT PROM software on this application module.ro DisplayString .1.3.6.1.4.1.326.2.2.1.1.2.6.1.7 |
appModuleOosLedThe color of the OOS LED on the application module. This LED is off (1) when the network module is up and running and red (2) when the network module is down (administratively placed out of service or operationally down temporarily). For example, when the network module's hardware initialization is in progress, the LED will be red until the hardware initialization is complete.ro Enumeration .1.3.6.1.4.1.326.2.2.1.1.2.6.1.8 |
appModulePanicActionThis variable indicates the action to be taken if the on-board CPU fails. This module will be reset if this variable is set to reset(1) and will be suspended if this variable is set to suspend(2).rw Enumeration .1.3.6.1.4.1.326.2.2.1.1.2.6.1.9 |
timing OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.3 |
netmodTimingGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.3.1 |
netmodTimingTableThis table is deprecated as the advanced timing options are removed.obsolete SEQUENCE OF NetmodTimingEntry .1.3.6.1.4.1.326.2.2.1.3.1.1 |
netmodTimingEntryA table entry containing network modeul timing information.obsolete NetmodTimingEntry .1.3.6.1.4.1.326.2.2.1.3.1.1.1 |
ntBoardThe index of this board within the ATM switch.roobsolete Integer32 .1.3.6.1.4.1.326.2.2.1.3.1.1.1.1 |
ntModuleThe number of this network module within the switch board.roobsolete Integer32 .1.3.6.1.4.1.326.2.2.1.3.1.1.1.2 |
ntPrimaryRecoveredClockThe port number on this network module that provides the primary 8KHz reference clock from its received signal.rwobsolete Integer32 .1.3.6.1.4.1.326.2.2.1.3.1.1.1.3 |
ntSecondaryRecoveredClockThe port number on this network module that provides the secondary 8KHz reference clock from its received signal.rwobsolete Integer32 .1.3.6.1.4.1.326.2.2.1.3.1.1.1.4 |
ntPrimaryExportClockThe primary 8KHz clock exported by this network module. The exported clock may be used as the network module global clock, which in turn, may be used by all ports that link their transmit clock to the network module global clock. The noClock option is valid only for tp25 (25mb) netmods.rwobsolete Enumeration .1.3.6.1.4.1.326.2.2.1.3.1.1.1.5 |
ntSecondaryExportClockThe secondary 8KHz clock exported by this network module. The exported clock may be used as the network module global clock. The secondary exported clock will be used if the primary exported clock is not available. The noClock option is valid only for tp25 (25mb) netmods.rwobsolete Enumeration .1.3.6.1.4.1.326.2.2.1.3.1.1.1.6 |
ntGlobalClockThe global 8KHz clock that is available to every port on this network module, when the port links its trasnmit clock to the network module global clock.rwobsolete Enumeration .1.3.6.1.4.1.326.2.2.1.3.1.1.1.7 |
ntExportClockOperStatusThe currently active 8KHz clock configuration. The tertiaryClock(3) is determined by the switch control software if both the primary and secondary clocks are not available.roobsolete Enumeration .1.3.6.1.4.1.326.2.2.1.3.1.1.1.8 |
ntPrimaryImportClockThe primary 8kHz clock imported by this network module. The imported clock may be used as the network module global clock, which in turn, may be used by all ports that link their transmit clock to the network module global clock.rwobsolete Enumeration .1.3.6.1.4.1.326.2.2.1.3.1.1.1.9 |
ntSecondaryImportClockThe secondary 8kHz clock imported by this network module. The imported clock may be used as the network module global clock. The secondary imported clock will be used if the primary imported clock is not available.rwobsolete Enumeration .1.3.6.1.4.1.326.2.2.1.3.1.1.1.10 |
ntImportClockOperStatusThe currently active 8kHz import clock configuration. The tertiaryClock(3) is determined by the switch control software if both the primary and secondary clocks are not available.roobsolete Enumeration .1.3.6.1.4.1.326.2.2.1.3.1.1.1.11 |
boardTimingGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.3.2 |
boardTimingTableThis table is deprecated as the advanced timing options are removed.obsolete SEQUENCE OF BoardTimingEntry .1.3.6.1.4.1.326.2.2.1.3.2.1 |
boardTimingEntryA table entry containing switch board timing information.obsolete BoardTimingEntry .1.3.6.1.4.1.326.2.2.1.3.2.1.1 |
btBoardThe index of this board within the ATM switch.roobsolete Integer32 .1.3.6.1.4.1.326.2.2.1.3.2.1.1.1 |
btPrimaryClockThe source of the primary 8kHz clock for this board. The clock may be used by each network module in the switch as the network module import clock. The clock may also be used by the management station as the primary or secondary source of the Stratum 3E clock.rwobsolete Enumeration .1.3.6.1.4.1.326.2.2.1.3.2.1.1.2 |
btSecondaryClockThe source of the secondary 8kHz clock. The clock may be used by the management station as the primary or secondary source of the Stratum 3E clock.rwobsolete Enumeration .1.3.6.1.4.1.326.2.2.1.3.2.1.1.3 |
btPrimaryClockOperStatusThe current state of the 8kHz primary clock.roobsolete Enumeration .1.3.6.1.4.1.326.2.2.1.3.2.1.1.4 |
btSecondaryClockOperStatusThe current state of the 8kHz secondary clock.roobsolete Enumeration .1.3.6.1.4.1.326.2.2.1.3.2.1.1.5 |
environment OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.4 |
alarmGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.4.1 |
swAlarmTableA table of switch alarm definitions and configuration. SEQUENCE OF SwAlarmEntry .1.3.6.1.4.1.326.2.2.1.4.1.1 |
swAlarmEntryA table entry containing switch alarm definitions. SwAlarmEntry .1.3.6.1.4.1.326.2.2.1.4.1.1.1 |
swAlarmTypeThe type of the alarm.ro Enumeration .1.3.6.1.4.1.326.2.2.1.4.1.1.1.1 |
swAlarmStatusThe status of this alarm entry. An alarm becomes active if the underlying condition is detected. For power supplies, the input failed alarm condition is asserted if the input voltage is not within the nominal range for the supply. This does not necessarily mean that an ouput failure will result. A power supply output failure condition is asserted if any power supply is failing or if it is physically removed. Power supply output alarms are only applicable to switches with multiple power supplies. Fan bank and temperature sensor failures are applicable only to switches with the appropriate sensing capabilities. Link and spans failures are applicable to all switches.ro Enumeration .1.3.6.1.4.1.326.2.2.1.4.1.1.1.2 |
swAlarmMinorCategoryThis object indicates whether a minor alarm is triggered when this event occurs.rw Enumeration .1.3.6.1.4.1.326.2.2.1.4.1.1.1.3 |
swAlarmMajorCategoryThis object indicates whether a major alarm is triggered when this event occurs.rw Enumeration .1.3.6.1.4.1.326.2.2.1.4.1.1.1.4 |
swAlarmResetThe manager may set this to the value 0 or 1 to cancel a current alarm. This is useful for silencing alarms triggered via edge detection. If this variable is readable, then the alarm is resettable.rw Enumeration .1.3.6.1.4.1.326.2.2.1.4.1.1.1.5 |
swAlarmCriticalCategoryThis object indicates whether a critical alarm is triggered when this event occurs. This is supported only on certain platforms.rw Enumeration .1.3.6.1.4.1.326.2.2.1.4.1.1.1.6 |
swAlarmACOStateThis object indicates the Alarm Cutoff Status(ACO) of this alarm entry. To silence an active alarm relay condition this value can be set to on(1), by pushing the front panel ACO button. The ACO is turned off when the alarm status(SwAlarmStatus) becomes inactive.ro Enumeration .1.3.6.1.4.1.326.2.2.1.4.1.1.1.7 |
swAlarmMajorRelayStateThis object indicates the current state of the major alarm relay. If one or more of the alarms (swAlarmType) that are defined major (swAlarmMajorCategory) are currently active (swAlarmStatus), and the alarm cutoff(swAlarmACOState) is off then this object will be on(1).ro Enumeration .1.3.6.1.4.1.326.2.2.1.4.1.2 |
swAlarmMinorRelayStateThis object indicates the current state of the minor alarm relay. If one or more of the alarms (swAlarmType) that are defined minor (swAlarmMinorCategory) are currently active (swAlarmStatus), and the alarm cutoff(swAlarmACOState) is off then this object will be on(1).ro Enumeration .1.3.6.1.4.1.326.2.2.1.4.1.3 |
swAlarmCriticalRelayStateThis object indicates the current state of the critical alarm relay. If one or more of the alarms (swAlarmType) that are defined critical (swAlarmCriticalCategory) are currently active (swAlarmStatus), and the alarm cutoff(swAlarmACOState) is off then this object will be on(1).ro Enumeration .1.3.6.1.4.1.326.2.2.1.4.1.4 |
swAlarmRelayTableThis table contains the alarm relay definitions for the switch alarms SEQUENCE OF SwAlarmRelayEntry .1.3.6.1.4.1.326.2.2.1.4.1.5 |
swAlarmRelayEntryThis entry contains the alarm relay definitions for the switch alarms. SwAlarmRelayEntry .1.3.6.1.4.1.326.2.2.1.4.1.5.1 |
swAlarmRelayIndexThis is the index of the alarm relay on the switch.ro Integer32 .1.3.6.1.4.1.326.2.2.1.4.1.5.1.1 |
swAlarmRelayFunctionThis is the alarm function associated with an alarm relay on the switch. An alarm relay may either be unused, assigned to one of critical, major and minor alarm.rw Enumeration .1.3.6.1.4.1.326.2.2.1.4.1.5.1.2 |
swAlarmRelayStateThis is the current state of the alarm relay. The state 'on' means that the alarm relay is activated; the state 'off' means that it is deactivated.ro Enumeration .1.3.6.1.4.1.326.2.2.1.4.1.5.1.3 |
swAlarmRelayOperModeThis variable represents the operational mode of the relay. The operational mode 'enabled' means that the relay is under software control and the relay state will reflect 'on' or 'off' according to the alarm conditions. 'disabled' will make the alarm relay state always 'off'. 'test' will make it always 'on'.rw Enumeration .1.3.6.1.4.1.326.2.2.1.4.1.5.1.4 |
powerGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.4.2 |
envMaxNumberOfPowerSuppliesThe maximum number of power supplies that can be installed on this ATM switch.ro Integer32 .1.3.6.1.4.1.326.2.2.1.4.2.1 |
envNumberOfPowerSuppliesThe number of power supply entries in the power supply table. This is the number of power supplies actually present.ro Integer32 .1.3.6.1.4.1.326.2.2.1.4.2.2 |
envPowerSupplyTableA table of power supply information. SEQUENCE OF EnvPowerSupplyEntry .1.3.6.1.4.1.326.2.2.1.4.2.3 |
envPowerSupplyEntryA table entry containing power supply information. EnvPowerSupplyEntry .1.3.6.1.4.1.326.2.2.1.4.2.3.1 |
envPowerSupplyIndexThe index of this power supply.ro Integer32 .1.3.6.1.4.1.326.2.2.1.4.2.3.1.1 |
envPowerSupplyTypeThe type of this power supply.ro Enumeration .1.3.6.1.4.1.326.2.2.1.4.2.3.1.2 |
envPowerSupplyInputStateThe state of the input voltage to this power supply.ro GeneralState .1.3.6.1.4.1.326.2.2.1.4.2.3.1.3 |
envPowerSupplyOutputStateThe status of the output of this power supply. In case there are several output supplies (like +5V, +12V, -12V) this object indicates the aggregate state of all outputs.ro GeneralState .1.3.6.1.4.1.326.2.2.1.4.2.3.1.4 |
envPowerSupplySerialNumberThe serial number of this power supply, if available.ro Integer32 .1.3.6.1.4.1.326.2.2.1.4.2.3.1.5 |
envPowerSupplyVersionThe version of this power supply, if available.ro Integer32 .1.3.6.1.4.1.326.2.2.1.4.2.3.1.6 |
envPowerSupplyCurrentStateThe state of the current on the input return path of this power supply. Should be within 28A +/-2A.ro GeneralState .1.3.6.1.4.1.326.2.2.1.4.2.3.1.7 |
envPowerSupply5VoltStateThe state of the +5V output of this power supply. Should be within tolerance of 5.0 +/-0.1VDC.ro GeneralState .1.3.6.1.4.1.326.2.2.1.4.2.3.1.8 |
fansGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.4.3 |
envNumberOfFanBanksThe number of fan banks on this ATM switch.ro Integer32 .1.3.6.1.4.1.326.2.2.1.4.3.1 |
envFanBanksTableA table of fan bank information. SEQUENCE OF EnvFanBanksEntry .1.3.6.1.4.1.326.2.2.1.4.3.2 |
envFanBanksEntryA table entry containing fan bank information. EnvFanBanksEntry .1.3.6.1.4.1.326.2.2.1.4.3.2.1 |
envFanBankIndexThe index of this fan bank.ro Integer32 .1.3.6.1.4.1.326.2.2.1.4.3.2.1.1 |
envFanBankStateThe status of the fan bank.ro GeneralState .1.3.6.1.4.1.326.2.2.1.4.3.2.1.3 |
envFanBankSerialNumberSerial number of the fan tray.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.4.3.2.1.4 |
envFanBankTypeThe type of fan bank installed.ro Integer32 .1.3.6.1.4.1.326.2.2.1.4.3.2.1.5 |
envFanBankRevisionThe revision of the fan bank, as an ASCII character.ro Integer32 .1.3.6.1.4.1.326.2.2.1.4.3.2.1.6 |
tempGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.4.4 |
envNumberOfTempSensorsThe number of temperature sensors installed on this ATM switch.ro Integer32 .1.3.6.1.4.1.326.2.2.1.4.4.1 |
envTempSensorsTableA table of temperature sensors information. SEQUENCE OF EnvTempSensorsEntry .1.3.6.1.4.1.326.2.2.1.4.4.2 |
envTempSensorsEntryA table entry containing temperature sensor information. EnvTempSensorsEntry .1.3.6.1.4.1.326.2.2.1.4.4.2.1 |
envTempSensorIndexThe index of this temperature sensor. The value of the index provides an indication of the location and function of the temperature sensor. The set of temperature sensors may vary by switch type.ro Enumeration .1.3.6.1.4.1.326.2.2.1.4.4.2.1.1 |
envTempSensorStateThe temperature state of this sensor.ro Enumeration .1.3.6.1.4.1.326.2.2.1.4.4.2.1.2 |
cpuGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.4.5 |
envMaxNumberOfCPUsThe maximum number of CPUs that can be installed on this ATM switch.ro Integer32 .1.3.6.1.4.1.326.2.2.1.4.5.1 |
envNumberOfCPUsThe number entries in the CPU table.ro Integer32 .1.3.6.1.4.1.326.2.2.1.4.5.2 |
envCPUsTableA table of CPU information. SEQUENCE OF EnvCPUsEntry .1.3.6.1.4.1.326.2.2.1.4.5.3 |
envCPUsEntryA table entry containing CPU information. EnvCPUsEntry .1.3.6.1.4.1.326.2.2.1.4.5.3.1 |
envCpuBoardThe board index of this CPU.ro Integer32 .1.3.6.1.4.1.326.2.2.1.4.5.3.1.1 |
envCpuSlotThe slot index of this CPU.ro Integer32 .1.3.6.1.4.1.326.2.2.1.4.5.3.1.2 |
envCpuTypeThe type of this CPU. The i960 processor further can be of three types - ca, cf and ha.ro Enumeration .1.3.6.1.4.1.326.2.2.1.4.5.3.1.3 |
envCPUStateThe state of the processor.ro Enumeration .1.3.6.1.4.1.326.2.2.1.4.5.3.1.4 |
envCpuDRAMSizeThe size of the DRAM in bytes installed on the SCP.ro Integer32 .1.3.6.1.4.1.326.2.2.1.4.5.3.1.5 |
envCpuRevLevelThe revision level of the processor.ro Integer32 .1.3.6.1.4.1.326.2.2.1.4.5.3.1.6 |
envCpuFlashSizeSize of Flash in bytes installed on this SCP board.ro Integer32 .1.3.6.1.4.1.326.2.2.1.4.5.3.1.7 |
envCpuBoardRevisionRevision number of this SCP board. A 32-bit number with the most significant 16 bits represent the revison alphabet. For example, 0x20000 represents Rev B, 0xd0000 represents Rev M.ro Integer32 .1.3.6.1.4.1.326.2.2.1.4.5.3.1.8 |
envCpuPromRevisionRevision number of the SCP PROM. Currently only available for boards with i960HA and i960HD processors. A 32-bit number. For example, 0x20000 represents Rev 2.0 and 0x20001 represents Rev 2.1ro Integer32 .1.3.6.1.4.1.326.2.2.1.4.5.3.1.9 |
envCpuMACAddressMAC address of ethernet chip on the SCP board.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.4.5.3.1.10 |
envCpuSerialNumberSerial number of the SCP card. This gives the SCPIM serial number on an ASX-4000.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.4.5.3.1.11 |
envCpuProductPartNumberProduct part number of the SCE. This gives the marketing product part number of RASCAL.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.4.5.3.1.12 |
envCpuCLEIThe Common Language Equipment Identification (CLEI) of this SCP.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.4.5.3.1.13 |
envCpuIDESizeSize of IDE disk in bytes installed on this SCP board.ro Integer32 .1.3.6.1.4.1.326.2.2.1.4.5.3.1.14 |
mgmtGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.4.6 |
envMgmtBoardTypeThe board type of the management station or backplane.ro Integer32 .1.3.6.1.4.1.326.2.2.1.4.6.1 |
envMgmtBoardRevisionThe board revision number of the management station or backplane.ro Integer32 .1.3.6.1.4.1.326.2.2.1.4.6.2 |
envMgmtBoardSerialNumberThe serial number of the management station or backplane.ro Integer32 .1.3.6.1.4.1.326.2.2.1.4.6.3 |
fabricGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.4.7 |
envFabricAlarmTripTemperatureThe temperature threshold in degrees C at which a fabric temperature alarm will be raised.rw Integer32 .1.3.6.1.4.1.326.2.2.1.4.7.1 |
envFabricAlarmResetTemperatureThe temperature in degrees C at which a fabric temperature alarm will be cancelled.rw Integer32 .1.3.6.1.4.1.326.2.2.1.4.7.2 |
envFabricTableA table of fabric environmental information SEQUENCE OF EnvFabricEntry .1.3.6.1.4.1.326.2.2.1.4.7.3 |
envFabricEntryA table containing fabric environmental information EnvFabricEntry .1.3.6.1.4.1.326.2.2.1.4.7.3.1 |
envFabricIndexThe index of the fabricro Integer32 .1.3.6.1.4.1.326.2.2.1.4.7.3.1.1 |
envFabricTemperatureThe temperature measured at the fabric, in degrees Cro Integer32 .1.3.6.1.4.1.326.2.2.1.4.7.3.1.2 |
envFabricTemperatureStateThe software state of this fabric temperature sensor. This will indicate `normal' until the sensor temperature reaches the current trip threshold. It will then indicate `overTemp' until the temperature reaches the current reset threshold (or until the switch fabric is restarted).ro Enumeration .1.3.6.1.4.1.326.2.2.1.4.7.3.1.3 |
shmem OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.5 |
netmodShmemGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.5.1 |
shmemConfTableA table for shared memory network modules configuration. Implementation of this table is mandatory if at least one of the network modules' hardware is based on shared memory. The user should walk this table and select the shared memory configuration that suits his/her needs. The selection is done in the specific network module shared memory configuration entry (netmodShmemTable). SEQUENCE OF ShmemConfEntry .1.3.6.1.4.1.326.2.2.1.5.1.1 |
shmemConfEntryA table entry containing shared memory network module configuration information. ShmemConfEntry .1.3.6.1.4.1.326.2.2.1.5.1.1.1 |
shmemConfIndexThe index of this shared memory configuration.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.1.1.1.1 |
shmemUcastConnectionsThe maximum number of unicast connections that is supported by this shared memory configuration.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.1.1.1.2 |
shmemMcastConnectionsThe maximum number of multicast connections that is supported by this shared memory configuration.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.1.1.1.3 |
shmemVpiVciListsThe memory allocated for VPI/VCI lists (which is used for multicast connections) by this shared memory configuration.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.1.1.1.4 |
shmemCellsBuffersThe number of cells buffers that is supported by this shared memory configuration.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.1.1.1.5 |
shmemConfNameThe name of this shared memory configuration.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.5.1.1.1.6 |
shmemMemorySizeThe size of this shared memory configuration in units of 48 bit words (x48).ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.1.1.1.7 |
netmodShmemTableA table for shared memory network modules configuration. Implementation of this table is mandatory if the network module hardware is based on shared memory. SEQUENCE OF NetmodShmemEntry .1.3.6.1.4.1.326.2.2.1.5.1.2 |
netmodShmemEntryA table entry containing shared memory network module configuration information. NetmodShmemEntry .1.3.6.1.4.1.326.2.2.1.5.1.2.1 |
nshmemBoardThe index of this board within the ATM switch.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.1.2.1.1 |
nshmemModuleThe number of this network module within the switch board.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.1.2.1.2 |
nshmemConfRowThis object identify the row in the shared memory configuration table that was selected for this network module.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.1.2.1.3 |
nshmemConfSharedMemoryThe amount of memory that was configured for this network module given all the user requirements as specified in the selected shared memory configuration row.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.1.2.1.4 |
nshmemCurrentUcastConnectionsThe current number of unicast connections active on this shared memory network module.ro Gauge32 .1.3.6.1.4.1.326.2.2.1.5.1.2.1.5 |
nshmemCurrentMcastConnectionsThe current number of multicast connections active on this shared memory network module.ro Gauge32 .1.3.6.1.4.1.326.2.2.1.5.1.2.1.6 |
nshmemCurrentVpiVciListsThe current number of VPI/VCI lists active on this shared memory network module.ro Gauge32 .1.3.6.1.4.1.326.2.2.1.5.1.2.1.7 |
nshmemCurrentCellsBuffersThe current number cells buffers active on this shared memory network module.ro Gauge32 .1.3.6.1.4.1.326.2.2.1.5.1.2.1.8 |
nshmemCurrentSharedMemoryThe current value of the used shared memory on this network module.ro Gauge32 .1.3.6.1.4.1.326.2.2.1.5.1.2.1.9 |
nshmemConfAal5PacketDropThe AAL5 packet drop threshold in percentage of cells. The switch software provides a reasonable default, however, the user may wish to change this value according to the type of traffic and size of packets being transmitted on the network.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.1.2.1.10 |
nshmemAssertXACPTThis variable establishes the setting fo the XACPT bit in the fs200sm main control register (section 3.1). This bit determines whether the signal XACPT is asserted whenever the shared memory is full. XACPT prevents the switch from sending cells to the network module. This bit takes advantage of any buffers on the switch to reduce cell loss, but it should not be used if guaranteed cell delay is being provided to high priority cells.rw Enumeration .1.3.6.1.4.1.326.2.2.1.5.1.2.1.11 |
nshmemMemorySizeThe size of this Series-C network module's shared memory in units of 48 bit words (x48).ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.1.2.1.12 |
portShmemGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.5.2 |
portShmemConfTableA table for shared memory network modules configuration that is specified on a port basis. Implementation of this table is mandatory if the network module hardware is based on shared memory. SEQUENCE OF PortShmemConfEntry .1.3.6.1.4.1.326.2.2.1.5.2.1 |
portShmemConfEntryA table entry containing port configuration information for shared memory network modules. PortShmemConfEntry .1.3.6.1.4.1.326.2.2.1.5.2.1.1 |
pshmemConfBoardThe index of this board within the ATM switch.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.2.1.1.1 |
pshmemConfModuleThe number of this network module within the switch board.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.2.1.1.2 |
pshmemConfPortThe number of this port within the switch board and network module.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.2.1.1.3 |
pshmemMaxCDVforCBRThe maximum transmitting CDV (Cell Delay Variation) in microseconds for CBR (Constant Bit Rate) / rtVBR (Real-Time Variable Bit Rate) traffic.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.2.1.1.4 |
pshmemMaxCDVforVBRThe maximum transmitting CDV (Cell Delay Variation) in microseconds for nrtVBR (Non-Real-Time Variable Bit Rate) traffic.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.2.1.1.5 |
pshmemQsizeforABRThe dedicated queue size in cells for ABR (Available Bit Rate) traffic.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.2.1.1.6 |
pshmemEfciOnABRThe treshold on which the EFCI (Explicit Forward Congestion Indication) bit is turned on for ABR (Available Bit Rate) and UBR (Unspecified Bit Rate) traffic.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.2.1.1.7 |
pshmemEfciOffABRThe treshold on which the EFCI (Explicit Forward Congestion Indication) bit is turned off for ABR (Available Bit Rate) and UBR (Unspecified Bit Rate) traffic.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.2.1.1.8 |
pshmemQsizeforCBRThe dedicated queue size in cells for CBR (Constant Bit Rate) / rtVBR (Real-Time Variable Bit Rate) traffic.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.2.1.1.9 |
pshmemQsizeforVBRThe dedicated queue size in cells for nrtVBR (Non-Real-Time Variable Bit Rate) traffic.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.2.1.1.10 |
pshmemClpThreshforCBRThe CLP=1 discard threshold in cells for CBR (Constant Bit Rate) / rtVBR (Real-Time Variable Bit Rate) traffic.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.2.1.1.11 |
pshmemClpThreshforVBRThe CLP=1 discard threshold in cells for nrtVBR (Non-Real-Time Variable Bit Rate) traffic.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.2.1.1.12 |
pshmemClpThreshforABRThe CLP=1 discard threshold in cells for ABR (Available Bit Rate) traffic.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.2.1.1.13 |
pShmemAtmInterfaceIndexThe Atm interface index correspong to this port. This is also the index of the portTable.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.2.1.1.14 |
portShmemTableA table for current state of port on shared memory network modules. Implementation of this table is mandatory if the network module hardware is based on shared memory. SEQUENCE OF PortShmemEntry .1.3.6.1.4.1.326.2.2.1.5.2.2 |
portShmemEntryA table entry containing current port configuration information for shared memory network modules. PortShmemEntry .1.3.6.1.4.1.326.2.2.1.5.2.2.1 |
pshmemBoardThe index of this board within the ATM switch.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.2.2.1.1 |
pshmemModuleThe number of this network module within the switch board.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.2.2.1.2 |
pshmemPortThe number of this port within the switch board and network module.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.2.2.1.3 |
pshmemPriorityThe traffic type.ro Enumeration .1.3.6.1.4.1.326.2.2.1.5.2.2.1.4 |
pshmemClpThresholdThe threshold level in number of cells in which CLP=1 cells will be dropped.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.2.2.1.5 |
pshmemDedicatedQsizeThe dedicated queue size for this type of traffic as was calculated by the switch software. The dedicated queue size is determined by the configured maximum CDV (Cell Delay Variation) for CBR/rtVBR (Constant Bit Rate / Real-Time Variable Bit Rate) and nrtVBR (Non-Real-Time Variable Bit Rate) as well as the configurable queue size for ABR (Available Bit Rate) and UBR (Unspecified Bit Rate) traffic.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.2.2.1.6 |
pshmemCurrentQsizeThe current size of the queue.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.2.2.1.7 |
pshmemTxCellsThe number of cells that were transmitted for this port and priority queue.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.2.2.1.8 |
pshmemLostCellsThe total number of cells that were lost for this port and priority queue.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.2.2.1.9 |
netmodShmem2Group OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.5.3 |
shmem2ConfTableA table for shared memory network modules configuration. Implementation of this table is mandatory if at least one of the network modules' hardware is based on shared memory. The user should walk this table and select the shared memory configuration that suits his/her needs. The selection is done in the specific network module shared memory configuration entry (netmodShmemTable). SEQUENCE OF Shmem2ConfEntry .1.3.6.1.4.1.326.2.2.1.5.3.1 |
shmem2ConfEntryA table entry containing shared memory network module configuration information. Shmem2ConfEntry .1.3.6.1.4.1.326.2.2.1.5.3.1.1 |
shmem2ConfIndexThe index of this shared memory configuration.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.3.1.1.1 |
shmem2UcastConnectionsThe maximum number of unicast connections that is supported by this shared memory configuration.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.3.1.1.2 |
shmem2McastConnectionsThe maximum number of multicast connections that is supported by this shared memory configuration.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.3.1.1.3 |
shmem2CellsBuffersThe number of cells buffers that is supported by this shared memory configuration.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.3.1.1.4 |
shmem2ConfNameThe name of this shared memory configuration.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.5.3.1.1.5 |
shmem2CountersThe number of counters that is supported by this shared memory configuration.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.3.1.1.6 |
shmem2CellMemorySizeThe size of this shared memory cell RAM configuration in units of 64 bit words (x64).ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.3.1.1.7 |
shmem2TableMemorySizeThe size of this shared memory table RAM configuration in units of 32 bit words (x32).ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.3.1.1.8 |
shmem2NumPrioritiesThe number of priorities that this shared memory configuration supports.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.3.1.1.9 |
netmodShmem2TableA table for shared memory network modules configuration. Implementation of this table is mandatory if the network module hardware is based on shared memory. SEQUENCE OF NetmodShmem2Entry .1.3.6.1.4.1.326.2.2.1.5.3.2 |
netmodShmem2EntryA table entry containing shared memory network module configuration information. NetmodShmem2Entry .1.3.6.1.4.1.326.2.2.1.5.3.2.1 |
nShmem2BoardThe index of this board within the ATM switch.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.3.2.1.1 |
nShmem2ModuleThe number of this network module within the switch board.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.3.2.1.2 |
nShmem2ConfRowThis object identify the row in the shared memory configuration table that was selected for this network module.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.3.2.1.3 |
nShmem2ConfSharedMemoryThe amount of memory that was configured for this network module given all the user requirements as specified in the selected shared memory configuration row.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.3.2.1.4 |
nShmem2CurrentUcastConnectionsThe current number of unicast connections active on this shared memory network module.ro Gauge32 .1.3.6.1.4.1.326.2.2.1.5.3.2.1.5 |
nShmem2CurrentMcastConnectionsThe current number of multicast connections active on this shared memory network module.ro Gauge32 .1.3.6.1.4.1.326.2.2.1.5.3.2.1.6 |
nShmem2CurrentCellsBuffersThe current number cells buffers active on this shared memory network module.ro Gauge32 .1.3.6.1.4.1.326.2.2.1.5.3.2.1.7 |
nShmem2CurrentSharedMemoryThe current value of the used shared memory on this network module.ro Gauge32 .1.3.6.1.4.1.326.2.2.1.5.3.2.1.8 |
nShmem2ConfAal5PacketDropThe AAL5 packet drop threshold in percentage of cells. The switch software provides a reasonable default, however, the user may wish to change this value according to the type of traffic and size of packets being transmitted on the network.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.3.2.1.9 |
nShmem2ConfAal5PacketDropforUBRThe AAL5 packet drop threshold, in percentage of cells for UBR queue in a four priority configuration or priorityNrt queue in a two priority configuration. The switch software provides a reasonable default. However, the user may wish to change this value according to the type of traffic and size of packets being transmitted on the network.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.3.2.1.10 |
nShmem2ConfEfciOnThe threshold on which the EFCI (Explicit Forward Congestion Indication) is enabled for UBR (Unspecified Bit Rate) and ABR (Available Bit Rate) traffic.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.3.2.1.11 |
nShmem2ConfEfciOffThe threshold on which the EFCI (Explicit Forward Congestion Indication) is disabled for UBR (Unspecified Bit Rate) and ABR (Available Bit Rate) traffic.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.3.2.1.12 |
nShmem2CellMemorySizeThe size of this shared memory cell RAM configuration in units of 64 bit words (x64).ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.3.2.1.13 |
nShmem2TableMemorySizeThe size of this shared memory table RAM configuration in units of 32 bit words (x32).ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.3.2.1.14 |
nShmem2NumPrioritiesThe number of priorities that this network module supports.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.3.2.1.15 |
nShmem2VBRPriorityThe queue through which VBR traffic is routed in a two priority configuration (priorityRt or priorityNrt). For a four priority configuration, it is unSupported.rw Enumeration .1.3.6.1.4.1.326.2.2.1.5.3.2.1.16 |
netmodShmem2CustomBCSTableA table for shared memory custom BCS mappings SEQUENCE OF NetmodShmem2CustomBCSEntry .1.3.6.1.4.1.326.2.2.1.5.3.3 |
netmodShmem2CustomBCSEntryA table entry containing shared memory custom BCS mappings NetmodShmem2CustomBCSEntry .1.3.6.1.4.1.326.2.2.1.5.3.3.1 |
nShmem2CustomBCSBoardThe index of this board within the ATM switch. Integer32 .1.3.6.1.4.1.326.2.2.1.5.3.3.1.1 |
nShmem2CustomBCSModuleThe number of this network module within the switch board. Integer32 .1.3.6.1.4.1.326.2.2.1.5.3.3.1.2 |
nShmem2CustomBCSValueThe value of this BCS Integer32 .1.3.6.1.4.1.326.2.2.1.5.3.3.1.3 |
nShmem2CustomBCSWeightThe weight assigned to this BCSrw Integer32 .1.3.6.1.4.1.326.2.2.1.5.3.3.1.4 |
nShmem2CustomBCSRowStatusAdministrative status of this entryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.5.3.3.1.5 |
portShmem2Group OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.5.4 |
portShmem2ConfTableA table for shared memory network modules configuration that is specified on a port basis. Implementation of this table is mandatory if the network module hardware is based on shared memory. SEQUENCE OF PortShmem2ConfEntry .1.3.6.1.4.1.326.2.2.1.5.4.1 |
portShmem2ConfEntryA table entry containing port configuration information for shared memory network modules. PortShmem2ConfEntry .1.3.6.1.4.1.326.2.2.1.5.4.1.1 |
pShmem2ConfBoardThe index of this board within the ATM switch.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.4.1.1.1 |
pShmem2ConfModuleThe number of this network module within the switch board.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.4.1.1.2 |
pShmem2ConfPortThe number of this port within the switch board and network module.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.4.1.1.3 |
pShmem2QsizeforCBRThe dedicated queue size in cells for CBR (Constant Bit Rate) / rtVBR (Real-Time Variable Bit Rate) traffic.rwdeprecated Integer32 .1.3.6.1.4.1.326.2.2.1.5.4.1.1.4 |
pShmem2QsizeforVBRThe dedicated queue size in cells for nrtVBR (Non-Real-Time Variable Bit Rate) traffic.rwdeprecated Integer32 .1.3.6.1.4.1.326.2.2.1.5.4.1.1.5 |
pShmem2QsizeforABRThe dedicated queue size in cells for ABR (Available Bit Rate) traffic.rwdeprecated Integer32 .1.3.6.1.4.1.326.2.2.1.5.4.1.1.6 |
pShmem2QsizeforUBRThe dedicated queue size in cells for UBR (Unspecified Bit Rate) traffic.rwdeprecated Integer32 .1.3.6.1.4.1.326.2.2.1.5.4.1.1.7 |
pShmem2ClpThreshforCBRThe CLP=1 discard threshold in cells for CBR (Constant Bit Rate) / rtVBR (Real-Time Variable Bit Rate) traffic.rwdeprecated Integer32 .1.3.6.1.4.1.326.2.2.1.5.4.1.1.8 |
pShmem2ClpThreshforVBRThe CLP=1 discard threshold in cells for nrtVBR (Non-Real-Time Variable Bit Rate) traffic.rwdeprecated Integer32 .1.3.6.1.4.1.326.2.2.1.5.4.1.1.9 |
pShmem2ClpThreshforABRThe CLP=1 discard threshold in cells for ABR (Available Bit Rate) traffic.rwdeprecated Integer32 .1.3.6.1.4.1.326.2.2.1.5.4.1.1.10 |
pShmem2ClpThreshforUBRThe CLP=1 discard threshold in cells for UBR (Unspecified Bit Rate) traffic.rwdeprecated Integer32 .1.3.6.1.4.1.326.2.2.1.5.4.1.1.11 |
pShmem2AtmInterfaceIndexThe Atm interface index correspong to this port. This is also the index of the portTable.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.4.1.1.12 |
portShmem2TableA table for current state of port on shared memory network modules. Implementation of this table is mandatory if the network module hardware is based on shared memory. SEQUENCE OF PortShmem2Entry .1.3.6.1.4.1.326.2.2.1.5.4.2 |
portShmem2EntryA table entry containing current port configuration information for shared memory network modules. PortShmem2Entry .1.3.6.1.4.1.326.2.2.1.5.4.2.1 |
pShmem2BoardThe index of this board within the ATM switch.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.4.2.1.1 |
pShmem2ModuleThe number of this network module within the switch board.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.4.2.1.2 |
pShmem2PortThe number of this port within the switch board and network module.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.4.2.1.3 |
pShmem2PriorityThe priority queue in the shared memory network module.ro Enumeration .1.3.6.1.4.1.326.2.2.1.5.4.2.1.4 |
pShmem2ClpThresholdThe threshold level in number of cells in which CLP=1 cells will be dropped.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.4.2.1.5 |
pShmem2DedicatedQsizeThe dedicated queue size for this type of traffic as was calculated by the switch software. The dedicated queue size is determined by the configured maximum CDV (Cell Delay Variation) for CBR/rtVBR (Constant Bit Rate / Real-Time Variable Bit Rate) and nrtVBR (Non-Real-Time Variable Bit Rate) as well as the configurable queue size for ABR (Available Bit Rate) and UBR (Unspecified Bit Rate) traffic.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.4.2.1.6 |
pShmem2CurrentQsizeThe current size of the queue.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.4.2.1.7 |
pShmem2TxCellsThe number of cells that were transmitted for this port and priority queue.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.4.2.1.8 |
pShmem2LostCellsThe total number of cells that were lost for this port and priority queue.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.4.2.1.9 |
pShmem2IntentionalLostCellsThe number of cells that were lost for this port and priority queue due to EPD (Early Packet Discard) or PPD (Partial Packet Discard).ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.4.2.1.10 |
pShmem2UnintentionalLostCellsThe number of cells that were lost for this port and priority queue due to output memory shortages or the CLP (Cell Loss Priority) threshold.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.4.2.1.11 |
portPriorityShmem2ConfTableA table for shared memory network modules configuration that is specified on a port-priority basis. Implementation of this table is mandatory if the network module hardware is based on shared memory. SEQUENCE OF PortPriorityShmem2ConfEntry .1.3.6.1.4.1.326.2.2.1.5.4.3 |
portPriorityShmem2ConfEntryA table entry containing port-priority configuration information for shared memory network modules. PortPriorityShmem2ConfEntry .1.3.6.1.4.1.326.2.2.1.5.4.3.1 |
ppShmem2ConfBoardThe index of this board within the ATM switch.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.4.3.1.1 |
ppShmem2ConfModuleThe number of this network module within the switch board.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.4.3.1.2 |
ppShmem2ConfPortThe number of this port within the switch board and the network module.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.4.3.1.3 |
ppShmem2ConfPriorityThe priority queue in the shared memory network module.ro Enumeration .1.3.6.1.4.1.326.2.2.1.5.4.3.1.4 |
ppShmem2QsizeThe dedicated queue size for this port-priority combination, in number of cells.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.4.3.1.5 |
ppShmem2ClpThresholdCLP=1 threshold of this port-priority combination, in number of cells.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.4.3.1.6 |
connShmem2Group OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.5.5 |
channelShmem2TableA table of information about the channels through this shared memory network module. SEQUENCE OF ChannelShmem2Entry .1.3.6.1.4.1.326.2.2.1.5.5.1 |
channelShmem2EntryA table entry containing channel shmem2 information. ChannelShmem2Entry .1.3.6.1.4.1.326.2.2.1.5.5.1.1 |
vcShmem2OutputPortThe value of this object identifies the output port of this channel and is the same as the opathPort, and portNumber.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.5.1.1.1 |
vcShmem2OutputVPIThe value of this object identifies the output VPI (Virtual Path Identifier) of this channel and is the same as the opathVPI.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.5.1.1.2 |
vcShmem2OutputVCIThe output VCI (Virtual Channel Identifier) of this channel.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.5.1.1.3 |
vcShmem2TotalLostCellsThe number of cells on this channel that were dropped by the output network module.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.5.1.1.4 |
vcShmem2IntentionalLostCellsThe number of cells on this channel that were dropped due to EPD (Early Packet Discard) or PPD (Partial Packet Discard).ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.5.1.1.5 |
vcShmem2UnintentionalLostCellsThe number of cells on this channel that were dropped due to output memory shortages or the CLP (Cell Loss Priority) threshold.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.5.1.1.6 |
vcShmem2TransmittedCellsThe number of cells on this channel that were transmitted.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.5.1.1.7 |
pathShmem2TableA table of information about the paths through this shared memory network module. SEQUENCE OF PathShmem2Entry .1.3.6.1.4.1.326.2.2.1.5.5.2 |
pathShmem2EntryA table entry containing path shmem2 information. PathShmem2Entry .1.3.6.1.4.1.326.2.2.1.5.5.2.1 |
vpShmem2OutputPortThe value of this object identifies the output port of this path and is the same as the portNumber.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.5.2.1.1 |
vpShmem2OutputVPIThe output VPI (Virtual Path Identifier) of this path.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.5.2.1.2 |
vpShmem2TotalLostCellsThe number of cells on this path that were dropped by the output network module.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.5.2.1.3 |
vpShmem2IntentionalLostCellsThe number of cells on this path that were dropped due to EPD (Early Packet Discard) or PPD (Partial Packet Discard).ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.5.2.1.4 |
vpShmem2UnintentionalLostCellsThe number of cells on this path that were dropped due to output memory shortages or the CLP (Cell Loss Priority) threshold.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.5.2.1.5 |
vpShmem2TransmittedCellsThe number of cells on this path that were transmitted.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.5.2.1.6 |
netmodShmem3Group OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.5.6 |
shmem3ConfTableA table for shared memory network modules configuration. Implementation of this table is mandatory if at least one of the network modules' hardware is based on shared memory. The user should walk this table and select the shared memory configuration that suits his/her needs. The selection is done in the specific network module shared memory configuration entry (netmodShmemTable). SEQUENCE OF Shmem3ConfEntry .1.3.6.1.4.1.326.2.2.1.5.6.1 |
shmem3ConfEntryA table entry containing shared memory network module configuration information. Shmem3ConfEntry .1.3.6.1.4.1.326.2.2.1.5.6.1.1 |
shmem3ConfIndexThe index of this shared memory configuration.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.1.1.1 |
shmem3UcastConnectionsThe maximum number of unicast connections that is supported by this shared memory configuration.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.1.1.2 |
shmem3McastConnectionsThe maximum number of multicast connections that is supported by this shared memory configuration.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.1.1.3 |
shmem3VpiVciListsThe memory allocated for VPI/VCI lists (which is used for multicast connections) by this shared memory configuration.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.1.1.4 |
shmem3CellsBuffersThe number of cells buffers that is supported by this shared memory configuration.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.1.1.5 |
shmem3ConfNameThe name of this shared memory configuration.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.5.6.1.1.6 |
shmem3CountersThe number of counters that is supported by this shared memory configuration.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.1.1.7 |
shmem3CellMemorySizeThe size of this shared memory cell RAM configuration.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.1.1.8 |
shmem3TableMemorySizeThe size of this shared memory table RAM configuration.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.1.1.9 |
netmodShmem3TableA table for shared memory network modules configuration. Implementation of this table is mandatory if the network module hardware is based on shared memory. SEQUENCE OF NetmodShmem3Entry .1.3.6.1.4.1.326.2.2.1.5.6.2 |
netmodShmem3EntryA table entry containing shared memory network module configuration information. NetmodShmem3Entry .1.3.6.1.4.1.326.2.2.1.5.6.2.1 |
nShmem3BoardThe index of this board within the ATM switch.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.2.1.1 |
nShmem3ModuleThe number of this network module within the switch board.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.2.1.2 |
nShmem3ConfRowThis object identify the row in the shared memory configuration table that was selected for this network module.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.2.1.3 |
nShmem3ConfSharedMemoryThe amount of memory that was configured for this network module given all the user requirements as specified in the selected shared memory configuration row.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.2.1.4 |
nShmem3CurrentUcastConnectionsThe current number of unicast connections active on this shared memory network module.ro Gauge32 .1.3.6.1.4.1.326.2.2.1.5.6.2.1.5 |
nShmem3CurrentMcastConnectionsThe current number of multicast connections active on this shared memory network module.ro Gauge32 .1.3.6.1.4.1.326.2.2.1.5.6.2.1.6 |
nShmem3CurrentVpiVciListsThe current number of VPI/VCI lists active on this shared memory network module.ro Gauge32 .1.3.6.1.4.1.326.2.2.1.5.6.2.1.7 |
nShmem3CurrentCellsBuffersThe current number cells buffers active on this shared memory network module.ro Gauge32 .1.3.6.1.4.1.326.2.2.1.5.6.2.1.8 |
nShmem3ConfAal5PacketDropThe AAL5 packet drop threshold in number of cells. The switch software provides a reasonable default, however, the user may wish to change this value according to the type of traffic and size of packets being transmitted on the network. Must be between 0 and 32767rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.2.1.10 |
nShmem3ConfAal5PacketDropforUBRThe AAL5 packet drop threshold for UBR traffic in percentage of cells. The switch software provides a reasonable default, however, the user may wish to change this value according to the type of traffic and size of packets being transmitted on the network. Must be between 0 and 32767rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.2.1.11 |
nShmem3ConfEfciOnThe threshold on which the EFCI (Explicit Forward Congestion Indication) is enabled for UBR (Unspecified Bit Rate) and ABR (Available Bit Rate) traffic. Must be a multiple of 32, greater than or equal to EFCI-off threshold, and less than or equal to 32736.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.2.1.12 |
nShmem3ConfEfciOffThe threshold on which the EFCI (Explicit Forward Congestion Indication) is disabled for UBR (Unspecified Bit Rate) and ABR (Available Bit Rate) traffic. Must be a multiple of 32, greater than or equal to 32, and less than or equal to EFCI-on threshold.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.2.1.13 |
nShmem3CellMemorySizeThe physical size of this shared memory cell RAM configuration.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.2.1.14 |
nShmem3TableMemorySizeThe physical size of this shared memory table RAM configuration.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.2.1.15 |
nShmem3ConfCountPacketsSetting this variable to enable(1) causes the network module to count the number of AAL5 packets.rw Enumeration .1.3.6.1.4.1.326.2.2.1.5.6.2.1.16 |
nShmem3ConfAltCLP1ThresholdAlternate CLP=1 threshold for nrt-VBR service class. Must be a multiple of 16, greater than or equal to 0, and less than AltCLP01 threshold.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.2.1.17 |
nShmem3ConfAltCLP01ThresholdAlternate CLP=0+1 threshold for nrt-VBR service class. Must be a multiple of 16, greater than AltCLP1 threshold and less than or equal to 4080.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.2.1.18 |
nShmem3ConfVcCLP1ForCBRPer class CLP=1 threshold for CBR/rtVBR service class. Must be a multiple of 16, greater than or equal to 0, and less than VcCLP01ForCBR threshold.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.2.1.19 |
nShmem3ConfVcCLP01ForCBRPer class CLP=0+1 threshold for CBR/rtVBR service class. Must be a multiple of 16, greater than VcCLP1ForCBR threshold, and less than or equal to 4080.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.2.1.20 |
nShmem3ConfVcCLP1ForVBRPer class CLP=1 threshold for nrt-VBR service class. Must be a multiple of 16, greater than or equal to 0, and less than VcCLP01ForVBR threshold.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.2.1.21 |
nShmem3ConfVcCLP01ForVBRPer class CLP=0+1 threshold for nrt-VBR service class. Must be a multiple of 16, greater than VcCLP1ForVBR threshold, and less than or equal to 4080.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.2.1.22 |
nShmem3ConfVcCLP1ForABRPer class CLP=1 threshold for ABR service class. Must be a multiple of 16, greater than or equal to 0, and less than VcCLP01ForABR threshold.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.2.1.23 |
nShmem3ConfVcCLP01ForABRPer class CLP=0+1 threshold for ABR service class. Must be a multiple of 16, greater than VcCLP1ForABR threshold, and less than or equal to 4080.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.2.1.24 |
nShmem3ConfVcCLP1ForUBRPer class CLP=1 threshold for UBR service class. Must be a multiple of 16, greater than or equal to 0, and less than VcCLP01ForUBR threshold.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.2.1.25 |
nShmem3ConfVcCLP01ForUBRPer class CLP=0+1 threshold for UBR service class. Must be a multiple of 16, greater than VcCLP1ForUBR threshold, and less than or equal to 4080.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.6.2.1.26 |
portShmem3Group OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.5.7 |
portShmem3ConfTableA table for shared memory network modules configuration that is specified on a port basis. Implementation of this table is mandatory if the network module hardware is based on shared memory. SEQUENCE OF PortShmem3ConfEntry .1.3.6.1.4.1.326.2.2.1.5.7.1 |
portShmem3ConfEntryA table entry containing port configuration information for shared memory network modules. PortShmem3ConfEntry .1.3.6.1.4.1.326.2.2.1.5.7.1.1 |
pShmem3ConfBoardThe index of this board within the ATM switch.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.7.1.1.1 |
pShmem3ConfModuleThe number of this network module within the switch board.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.7.1.1.2 |
pShmem3ConfPortThe number of this port within the switch board and network module.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.7.1.1.3 |
pShmem3QsizeforCBRThe dedicated queue size in cells for CBR (Constant Bit Rate) / rtVBR (Real-Time Variable Bit Rate) traffic.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.7.1.1.4 |
pShmem3QsizeforVBRThe dedicated queue size in cells for nrtVBR (Non-Real-Time Variable Bit Rate) traffic.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.7.1.1.5 |
pShmem3QsizeforABRThe dedicated queue size in cells for ABR (Available Bit Rate) traffic.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.7.1.1.6 |
pShmem3QsizeforUBRThe dedicated queue size in cells for UBR (Unspecified Bit Rate) traffic.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.7.1.1.7 |
pShmem3Clp01ThreshforCBRThe CLP=0+1 discard threshold in cells for CBR (Constant Bit Rate) / rtVBR (Real-Time Variable Bit Rate) traffic.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.7.1.1.8 |
pShmem3Clp1ThreshforCBRThe CLP=1 discard threshold in cells for CBR (Constant Bit Rate) / rtVBR (Real-Time Variable Bit Rate) traffic.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.7.1.1.9 |
pShmem3Clp01ThreshforVBRThe CLP=0+1 discard threshold in cells for nrtVBR (Variable Bit Rate) traffic.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.7.1.1.10 |
pShmem3Clp1ThreshforVBRThe CLP=1 discard threshold in cells for nrtVBR (Variable Bit Rate) traffic.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.7.1.1.11 |
pShmem3Clp01ThreshforABRThe CLP=0+1 discard threshold in cells for ABR (Available Bit Rate) traffic.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.7.1.1.12 |
pShmem3Clp1ThreshforABRThe CLP=1 discard threshold in cells for ABR (Available Bit Rate) traffic.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.7.1.1.13 |
pShmem3Clp01ThreshforUBRThe CLP=0+1 discard threshold in cells for UBR (Unspecified Bit Rate) traffic.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.7.1.1.14 |
pShmem3Clp1ThreshforUBRThe CLP=1 discard threshold in cells for UBR (Unspecified Bit Rate) traffic.rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.7.1.1.15 |
pShmem3RateLimitThe number of cells/second to limit this port. This in effect, sets a new logical line rate for this network module. If set to 0, rate-limiting is disabled. (i.e. full bandwidth is returned to the port).rw Integer32 .1.3.6.1.4.1.326.2.2.1.5.7.1.1.16 |
pShmem3ConfSVCSchedulingCBRThis variable defines the scheduling discipline that is going to be used to service all CBR SVC connections that are output across this Series-D port. roundrobin: On Series-D netmod, this means that all CBR SVC's will be served only by one of the two round robin queues. smoothed: On Series-D netmod, this means that all CBR SVC's will be served by the rate controller. guaranteed: On Series-D netmod, this means that all CBR SVC's will be served by both the rate controller and the round robin queues.rwdeprecated Enumeration .1.3.6.1.4.1.326.2.2.1.5.7.1.1.17 |
pShmem3ConfPVCSchedulingCBRThis variable defines the scheduling discipline that is going to be used to service all CBR PVC connections that are output across this port. Series-D netmods support all three scheduling modes. perupc: This means that each individual CBR PVC will be scheduled based on the discipline associated with the UPC contract used to open the connection. roundrobin: This means that each individual CBR PVC will served only by the rate controller. smoothed: On Series-D netmod, this means that all CBR PVC's will be served only by the rate controller. guaranteed: This means that all CBR PVC's will be served by both the rate controller and the round robin queues.rwdeprecated Enumeration .1.3.6.1.4.1.326.2.2.1.5.7.1.1.18 |
pShmem3ConfSVCSchedulingVBRThis variable defines the scheduling discipline that is going to be used to service all VBR SVC connections that are output across this Series-D port. roundrobin: On Series-D netmod, this means that all VBR SVC's will be served only by one of the two round robin queues. smoothed: On Series-D netmod, this means that all VBR SVC's will be served by the rate controller. guaranteed: On Series-D netmod, this means that all VBR SVC's will be served by both the rate controller and the round robin queues.rwdeprecated Enumeration .1.3.6.1.4.1.326.2.2.1.5.7.1.1.19 |
pShmem3ConfPVCSchedulingVBRThis variable defines the scheduling discipline that is going to be used to service all VBR PVC connections that are output across this port. Series-D netmods support all three scheduling modes. perupc: This means that each individual VBR PVC will be scheduled based on the discipline associated with the UPC contract used to open the connection. roundrobin: This means that each individual VBR PVC will served only by the rate controller. smoothed: On Series-D netmod, this means that all VBR PVC's will be served only by the rate controller. guaranteed: This means that all VBR PVC's will be served by both the rate controller and the round robin queues.rwdeprecated Enumeration .1.3.6.1.4.1.326.2.2.1.5.7.1.1.20 |
pShmem3ConfAltCLPConfigCBRThis vairable defines the per-port configuration for the use of the VC level Alternate CLP Thresholdold on CBR/rtVBR connections. The states mean the following: allOn: All CBR/rtVBR connections use the alt CLP threshold. allOff: No CBR/rtVBR connections use the alt CLP threshold. svcOn: All CBR/rtVBR SVC's will use the alt CLP threshold. For CBR/rtVBR PVC's, whether the alt CLP threshold is used is determined by the presence or absence of the 'altCLPthresh' flag in the UPC contract. svcOff: No CBR/rtVBR SVC's will use the alt CLP threshold. For CBR/rtVBR PVC's, whether the alt CLP threshold is used is determined by the presence or absence of the 'altCLPthresh' flag in the UPC contract.rw Enumeration .1.3.6.1.4.1.326.2.2.1.5.7.1.1.21 |
pShmem3ConfAltCLPConfigVBRThis vairable defines the per-port configuration for the use of the VC level Alternate CLP Thresholdold on nrtVBR connections. The states mean the following: allOn: All nrtVBR connections use the alt CLP threshold. allOff: No nrtVBR connections use the alt CLP threshold. svcOn: All nrtVBR SVC's will use the alt CLP threshold. For nrtVBR PVC's, whether the alt CLP threshold is used is determined by the presence or absence of the 'altCLPthresh' flag in the UPC contract. svcOff: No nrtVBR SVC's will use the alt CLP threshold. For nrtVBR PVC's, whether the alt CLP threshold is used is determined by the presence or absence of the 'altCLPthresh' flag in the UPC contract.rw Enumeration .1.3.6.1.4.1.326.2.2.1.5.7.1.1.22 |
pShmem3ConfAltCLPConfigUBRThis vairable defines the per-port configuration for the use of the VC level Alternate CLP Thresholdold on UBR connections. The states mean the following: allOn: All UBR connections use the alt CLP threshold. allOff: No UBR connections use the alt CLP threshold. svcOn: All UBR SVC's will use the alt CLP threshold. For UBR PVC's, whether the alt CLP threshold is used is determined by the presence or absence of the 'altCLPthresh' flag in the UPC contract. svcOff: No UBR SVC's will use the alt CLP threshold. For UBR PVC's, whether the alt CLP threshold is used is determined by the presence or absence of the 'altCLPthresh' flag in the UPC contract.rw Enumeration .1.3.6.1.4.1.326.2.2.1.5.7.1.1.23 |
pShmem3AtmInterfaceIndexThe Atm interface index correspong to this port. This is also the index of the portTable.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.7.1.1.24 |
portShmem3TableA table for current state of port on shared memory network modules. Implementation of this table is mandatory if the network module hardware is based on shared memory. SEQUENCE OF PortShmem3Entry .1.3.6.1.4.1.326.2.2.1.5.7.2 |
portShmem3EntryA table entry containing current port configuration information for shared memory network modules. PortShmem3Entry .1.3.6.1.4.1.326.2.2.1.5.7.2.1 |
pShmem3BoardThe index of this board within the ATM switch.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.7.2.1.1 |
pShmem3ModuleThe number of this network module within the switch board.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.7.2.1.2 |
pShmem3PortThe number of this port within the switch board and network module.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.7.2.1.3 |
pShmem3PriorityThe traffic type.ro Enumeration .1.3.6.1.4.1.326.2.2.1.5.7.2.1.4 |
pShmem3CurrentQsizeThe current size of the queue.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.7.2.1.5 |
pShmem3TxCellsThe number of cells that were transmitted for this port and priority queue.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.7.2.1.6 |
pShmem3EPDLostCellsThe number of cells that were lost for this port and priority queue due to EPD threshold.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.7.2.1.7 |
pShmem3CLP01LostCellsThe number of cells that were lost for this port and priority queue due CLP=0+1 threshold.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.7.2.1.8 |
pShmem3CLP1LostCellsThe number of cells that were lost for this port and priority queue due to CLP=1 threshold.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.7.2.1.9 |
pShmem3VcCLPLostCellsThe number of cells that were lost for this port and priority queue due to per VC CLP=1 and CLP=0+1 thresholds.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.7.2.1.10 |
pShmem3OverflowLostCellsThe number of cells that were lost for this port and priority queue due to memory overflows.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.7.2.1.11 |
pShmem3PPDLostCellsThe number of cells that were lost for this port and priority queue due to EPD, per port and per VC CLP, and memory overflows.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.7.2.1.12 |
connShmem3Group OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.5.8 |
channelShmem3TableA table of information about the channels through this shared memory network module. SEQUENCE OF ChannelShmem3Entry .1.3.6.1.4.1.326.2.2.1.5.8.1 |
channelShmem3EntryA table entry containing channel seriesD information. ChannelShmem3Entry .1.3.6.1.4.1.326.2.2.1.5.8.1.1 |
vcShmem3OutputPortThe value of this object identifies the output port of this channel and is the same as the opathPort, and portNumber.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.8.1.1.1 |
vcShmem3OutputVPIThe value of this object identifies the output VPI (Virtual Path Identifier) of this channel and is the same as the opathVPI.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.8.1.1.2 |
vcShmem3OutputVCIThe output VCI (Virtual Channel Identifier) of this channel.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.8.1.1.3 |
vcShmem3IntentionalLostCellsThe number of cells on this channel that were dropped due to EPD (Early Packet Discard) or PPD (Partial Packet Discard).ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.8.1.1.4 |
vcShmem3UnintentionalLostCellsThe number of cells on this channel that were dropped due to output memory shortages or the CLP (Cell Loss Priority) threshold.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.8.1.1.5 |
vcShmem3CLP0TxCellsThe number of CLP=0 cells on this channel that were transmitted.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.8.1.1.6 |
vcShmem3CLP1TxCellsThe number of CLP=1 cells on this channel that were transmitted.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.8.1.1.7 |
vcShmem3EPDLostCellsThe number of cells lost on this channel due to EPD.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.8.1.1.8 |
vcShmem3CLP1LostCellsThe number of cells lost on this channel due to CLP=1 threshold.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.8.1.1.9 |
vcShmem3CLP01LostCellsThe number of cells lost on this channel due to CLP=0+1 threshold.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.8.1.1.10 |
vcShmem3TransmittedPacketsThe number of transmitted packets.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.8.1.1.11 |
vcShmem3CurrentQsizeThe current size of the queue.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.8.1.1.12 |
pathShmem3TableA table of information about the paths through this shared memory network module. SEQUENCE OF PathShmem3Entry .1.3.6.1.4.1.326.2.2.1.5.8.2 |
pathShmem3EntryA table entry containing path seriesD information. PathShmem3Entry .1.3.6.1.4.1.326.2.2.1.5.8.2.1 |
vpShmem3OutputPortThe value of this object identifies the output port of this path and is the same as the portNumber.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.8.2.1.1 |
vpShmem3OutputVPIThe output VPI (Virtual Path Identifier) of this path.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.8.2.1.2 |
vpShmem3UnintentionalLostCellsThe number of cells on this path that were dropped due to output memory shortages or the CLP (Cell Loss Priority) threshold.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.8.2.1.4 |
vpShmem3CLP0TxCellsThe number of CLP=0 cells on this path that were transmitted.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.8.2.1.5 |
vpShmem3CLP1TxCellsThe number of CLP=1 cells on this path that were transmitted.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.8.2.1.6 |
vpShmem3CLP1LostCellsThe number of cells lost on this path due to CLP=1 threshold.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.8.2.1.8 |
vpShmem3CLP01LostCellsThe number of cells lost on this path due to CLP=0+1 threshold.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.8.2.1.9 |
vpShmem3TransmittedPacketsThe number of transmitted packets.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.8.2.1.10 |
vpShmem3CurrentQsizeThe current size of the queue.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.8.2.1.11 |
netmodGenericShmemGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.5.9 |
netmodGenericShmemTableA table for simple network modules. Implementation of this table is optional. SEQUENCE OF NetmodGenericShmemEntry .1.3.6.1.4.1.326.2.2.1.5.9.1 |
netmodGenericShmemEntryA table entry containing simple network module configuration information NetmodGenericShmemEntry .1.3.6.1.4.1.326.2.2.1.5.9.1.1 |
nGenericShmemBoardThe index of this board within the ATM switch.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.9.1.1.1 |
nGenericShmemModuleThe number of this network module within the switch board.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.9.1.1.2 |
nGenericShmemSubindexThe subindex of this generic shmem within the network module.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.9.1.1.3 |
nGenericShmemCurrentUcastConnectionsThe current number of unicast connections active on this network module. If a separate unicast connection space is not supported, this value will be -1.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.9.1.1.4 |
nGenericShmemCurrentMcastConnectionsThe current number of multicast connections active on this network module. If a separate multicast connection space is not supported, this value will be -1.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.9.1.1.5 |
nGenericShmemCurrentConnectionsThe current number of connections (either multicast or unicast) active on this network module.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.9.1.1.6 |
nGenericShmemMaxUcastConnectionsThe total number of unicast connections that this network module can support. If a separate unicast connection space is not supported, this value will be -1. The largest possible number of ATM connections can be 2^28 - 1 (i.e., 268435455) since VPI and VCI fields in the ATM cell header occupies a total of 28 bits (12 bits of VPI and 16 bits of VCI). Any value greater than 2^28 - 1 for this MIB will indicate that this network module can support an unlimited number of unicast connections.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.9.1.1.7 |
nGenericShmemMaxMcastConnectionsThe total number of multicast connections that this network module can support. If a separate multicast connection space is not supported, this value will be -1. The largest possible number of ATM connections can be 2^28 - 1 (i.e., 268435455) since VPI and VCI fields in the ATM cell header occupies a total of 28 bits (12 bits of VPI and 16 bits of VCI). Any value greater than 2^28 - 1 for this MIB will indicate that this network module can support an unlimited number of multicast connections.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.9.1.1.8 |
nGenericShmemMaxConnectionsThe total number of connections (either multicast or unicast) that this network module can support. The largest possible number of ATM connections can be 2^28 - 1 (i.e., 268435455) since VPI and VCI fields in the ATM cell header occupies a total of 28 bits (12 bits of VPI and 16 bits of VCI). Any value greater than 2^28 - 1 for this MIB will indicate that this network module can support an unlimited number of connections.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.9.1.1.9 |
genericPortGroupConfTableA table for simple network modules. Implementation of this table is optional. SEQUENCE OF GenericPortGroupConfEntry .1.3.6.1.4.1.326.2.2.1.5.9.2 |
genericPortGroupConfEntryA table entry containing simple network module configuration information GenericPortGroupConfEntry .1.3.6.1.4.1.326.2.2.1.5.9.2.1 |
genericPortGroupBoardThe index of this board within the ATM switch.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.9.2.1.1 |
genericPortGroupIndexThe number of this port group(module) within a switch board. This is the number that identifies the port group within a switch board.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.9.2.1.2 |
genericPortGroupSubindexThe subindex of this port group identifying a port within this port group.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.9.2.1.3 |
genericPortGroupPrioIndexThe priority on the port.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.9.2.1.4 |
genericPortGroupAal5PacketDropThe AAL5 packet drop threshold in percentage of cells. The switch software provides a reasonable default, however, the user may wish to change this value according to the type of traffic and size of packets being transmitted on the network.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.9.2.1.5 |
genericPortGroupEfciOnThe threshold at which the EFCI (Explicit Forward Congestion Indication) bit is turned on for ABR (Available Bit Rate) traffic.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.9.2.1.6 |
genericPortGroupEfciOffThe threshold at which the EFCI (Explicit Forward Congestion Indication) bit is turned off for ABR (Available Bit Rate) traffic.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.9.2.1.7 |
genericPortGroupPrioNameThe priority name (CBR, VBR, ABR, UBR) for this priority index.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.5.9.2.1.8 |
netmodGenericShmemCustomBCSTableA table for shared memory custom BCS mappings SEQUENCE OF NetmodGenericShmemCustomBCSEntry .1.3.6.1.4.1.326.2.2.1.5.9.3 |
netmodGenericShmemCustomBCSEntryA table entry containing shared memory custom BCS mappings NetmodGenericShmemCustomBCSEntry .1.3.6.1.4.1.326.2.2.1.5.9.3.1 |
nGenericShmemCustomBCSBoardThe index of this board within the ATM switch. Integer32 .1.3.6.1.4.1.326.2.2.1.5.9.3.1.1 |
nGenericShmemCustomBCSModuleThe number of this network module within the switch board. Integer32 .1.3.6.1.4.1.326.2.2.1.5.9.3.1.2 |
nGenericShmemCustomBCSSubindexThe subindex of this generic shmem within the network module. Integer32 .1.3.6.1.4.1.326.2.2.1.5.9.3.1.3 |
nGenericShmemCustomBCSValueThe value of this BCS Integer32 .1.3.6.1.4.1.326.2.2.1.5.9.3.1.4 |
nGenericShmemCustomBCSWeightThe weight assigned to this BCSrw Integer32 .1.3.6.1.4.1.326.2.2.1.5.9.3.1.5 |
nGenericShmemCustomBCSRowStatusAdministrative status of this entryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.5.9.3.1.6 |
genericOutputPortGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.5.10 |
genericOutputPortConfTableA table for managing the configurable items for a port in a generic manner. Implementation of this table is optional. SEQUENCE OF GenericOutputPortConfEntry .1.3.6.1.4.1.326.2.2.1.5.10.1 |
genericOutputPortConfEntryA table entry containing generic port configuration information GenericOutputPortConfEntry .1.3.6.1.4.1.326.2.2.1.5.10.1.1 |
genericOutputPortConfBoardThe index of this board within the ATM switchro Integer32 .1.3.6.1.4.1.326.2.2.1.5.10.1.1.1 |
genericOutputPortConfModuleThe number of this port group within the switch board.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.10.1.1.2 |
genericOutputPortConfPortThe number identifies the port within a switch board and a port group.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.10.1.1.3 |
genericOutputPortConfPrioThe priority on the output port.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.10.1.1.4 |
genericOutputPortConfPrioDedicatedQSizeThe dedicated (minimum) queue size, in cells for this pport and priorityro Integer32 .1.3.6.1.4.1.326.2.2.1.5.10.1.1.5 |
genericOutputPortConfPrioClp1ThresholdThe CLP=1 discard threshold, in cells for this port and priority.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.10.1.1.6 |
genericOutputPortConfPrioClp01ThresholdThe CLP=0+1 discard threshold, in cells for this port and priority.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.10.1.1.7 |
genericOutputPortConfPrioNameThe priority name (CBR, VBR, ABR, UBR) for this genericOutputPortIndex on this port.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.5.10.1.1.8 |
genericOutputPortConfAtmifThe AtmIf(BNP) of this shmem within the ATM switchro Integer32 .1.3.6.1.4.1.326.2.2.1.5.10.1.1.9 |
genericOutputPortStatsTableA table for managing Statistics information about the current state of a port in a generic manner. Implementation of this table is optional. SEQUENCE OF GenericOutputPortStatsEntry .1.3.6.1.4.1.326.2.2.1.5.10.2 |
genericOutputPortStatsEntryA table entry containing generic port configuration information GenericOutputPortStatsEntry .1.3.6.1.4.1.326.2.2.1.5.10.2.1 |
genericOutputPortStatsBoardThe index of this board within the ATM switch.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.10.2.1.1 |
genericOutputPortStatsModuleThe number of this port group within the switch board.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.10.2.1.2 |
genericOutputPortStatsPortThe number of this port within the switch board and the port group.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.10.2.1.3 |
genericOutputPortStatsPrioThe index of this priority.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.10.2.1.4 |
genericOutputPortStatsPrioTransmittedCellsThe number of cells transmitted on this port for this priorityro Counter32 .1.3.6.1.4.1.326.2.2.1.5.10.2.1.5 |
genericOutputPortStatsPrioClp1LostCellsThe number of cells lost on this port for this priority due to CLP=1 threshold.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.10.2.1.6 |
genericOutputPortStatsPrioClp01LostCellsThe number of cells lost on this port for this priority due to CLP=0+1 threshold.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.10.2.1.7 |
genericOutputPortStatsPrioNameThe priority name (CBR, VBR, ABR, UBR) for this genericOutputPortIndex on this port.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.5.10.2.1.8 |
genericOutputPortStatsAtmifThe index of Atmif associated with this shmem in the ATM switch.ro Integer32 .1.3.6.1.4.1.326.2.2.1.5.10.2.1.9 |
genericOutputPortStatsPrioEpdPpdLostCellsThe number of cells lost on this port for this priority due to EPD/PPD threshold.ro Counter32 .1.3.6.1.4.1.326.2.2.1.5.10.2.1.10 |
dualScp OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.6 |
dualScpGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.6.1 |
dualScpConfTableA table for current state of dual SCP configuration. SEQUENCE OF DualScpConfEntry .1.3.6.1.4.1.326.2.2.1.6.1.1 |
dualScpConfEntryA table entry containing current dual SCP configuration. DualScpConfEntry .1.3.6.1.4.1.326.2.2.1.6.1.1.1 |
dualScpSlotThe slot number for this SCP.ro Enumeration .1.3.6.1.4.1.326.2.2.1.6.1.1.1.1 |
dualScpStateShows whether the switch is operating with a single or dual SCPs. The value other(3) denotes that both SCPs are present but communication is not yet established.ro Enumeration .1.3.6.1.4.1.326.2.2.1.6.1.1.1.2 |
dualScpSyncStateThis variable contains the current state of synchronization.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.6.1.1.1.3 |
dualScpPrimaryControls which SCP is designated as the primary SCP.rw Enumeration .1.3.6.1.4.1.326.2.2.1.6.1.1.1.4 |
dualScpFailoverDisables the dual SCP failover mechanism. When set to disable(2), the backup SCP will not take over if the main SCP goes down.rw Enumeration .1.3.6.1.4.1.326.2.2.1.6.1.1.1.5 |
dualScpManualSyncRequestThis variable can be used to manually synchronize the entire flash or any of the specified files. syncIdle(1) - No synchronization. syncFlash(2) - Synchronize the entire flash. syncCdb(3) - Synchronize the CDB file. syncPassword(4) - Synchronize the password file (depracated). syncLecsConfig(5) - Synchronize the LECS configuration file. syncOS(6) - Synchronize the OS. syncInit(7) - Reformat the entire flash. syncSecurid(8) - Synchronize the securid configuration file. syncSecret(9) - Synchronize the securid node secret file. syncLoader(10) - Synchronize the mini-loader. syncKrb5KeyTab(12)- Synchronize the kerberos v5srvtab file.rw Enumeration .1.3.6.1.4.1.326.2.2.1.6.1.1.1.6 |
dualScpCdbSyncModeControls whether CDB synchronization will be manual or automatic.rw Enumeration .1.3.6.1.4.1.326.2.2.1.6.1.1.1.7 |
dualScpManualSwitchOverForces the backup SCP to take switch control from the main SCP.rw Enumeration .1.3.6.1.4.1.326.2.2.1.6.1.1.1.8 |
dualScpSwitchOverTimeShow the time when switch over occurred.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.6.1.1.1.9 |
dualScpSwitchOverThresholdAmount of time the standby SCP will wait after loss of active SCP's heartbeat before it takes control of the switch. The valid range is 2-300 seconds.rw Integer32 .1.3.6.1.4.1.326.2.2.1.6.1.1.1.10 |
dualScpSyncRequestListThe current list of items that are waiting to be synchronized. This is a bit pattern containing the specified enumurated bits. The bit definitions are: 0x02 -- syncFlash 0x04 -- syncCdb 0x08 -- syncPassword 0x10 -- syncLecsConfig 0x20 -- syncOS 0x40 -- syncInit 0x80 -- syncSecurid 0x100 -- syncSecret 0x200 -- syncLoader 0x800 -- syncKrb5KeyTabro IntegerBitString .1.3.6.1.4.1.326.2.2.1.6.1.1.1.11 |
dualScpNumSyncRequestsThe number of synchronization requests since this agent was initialized.ro Counter32 .1.3.6.1.4.1.326.2.2.1.6.1.1.1.12 |
dualScpNumSyncFailuresThe number of synchronization failures since this agent was initialized.ro Counter32 .1.3.6.1.4.1.326.2.2.1.6.1.1.1.13 |
dualScpResetStandbyScpSetting this variable to enable(1) resets the backup SCP forcing it to start over.rw Enumeration .1.3.6.1.4.1.326.2.2.1.6.1.1.1.14 |
dualScpAutoRemoveOldFilesSetting this variable to enable(1) instructs the backup SCP to remove old files during file synchronization in order to make room for the files that are being synchronized. This usually removes older copies of OS files. When synchronizing the OS, the current version of the OS will be removed if there isn't sufficient space for the new OS being synchronized.rw Enumeration .1.3.6.1.4.1.326.2.2.1.6.1.1.1.15 |
dualScpRedundancyStateThis variable contains the current state of Dual SCP Redundancy.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.1.6.1.1.1.16 |
dualScpSVXCPStateSyncPercentWhen SVx/SPVx Preservation is enabled, call state information will be transferred from the Active SCP to the Standby SCP, prior to any SCP control transfer. This MIB variable tracks the completion percentage of the information transfer. Before SCP control transfer occurs, the user can query this variable to find out how much of the information transfer has been done.ro Gauge .1.3.6.1.4.1.326.2.2.1.6.1.1.1.17 |
dualScpSVXCPStateTransferFailedWhen SVx/SPVx Preservation is enabled, call state information will be transferred from the Active SCP to the Standby SCP. The value returned is 'Failed' for any failure in this transfer, 'OK' otherwise.ro Enumeration .1.3.6.1.4.1.326.2.2.1.6.1.1.1.18 |
dualScpSVXCPdroppedCallCountSVx/SPVx Preservation has failed to preserve zero or more calls, whose number is given here.ro Integer32 .1.3.6.1.4.1.326.2.2.1.6.1.1.1.19 |
etherChipSet OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.10 |
etherChipSetDec OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.10.1 |
etherChipSetDec21440 OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.1.10.1.1 |
switchGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.1 |
hardwareVersionThe version of the ATM switch hardware in hex. The version number 0x1 is revision A, 0x2 is revision B etc. Version number 0x0 represents an unknown type.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.1.1 |
softwareVersionThe version of the ATM switch control software in hex. The version number is encoded into 6 hex digits. For example, version 1.2.3 is encoded as 0x010203.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.1.2 |
maxPathsThe maximum number of input VPIs (Virtual Path Identifies).ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.1.3 |
maxChannelsThe maximum number of input VCIs (Virtual Channel Identifiers).ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.1.4 |
atmAddressThe address of this ATM switch.ro SpansAddress .1.3.6.1.4.1.326.2.2.2.1.1.5 |
uptimeThe length of time this ATM switch has been up, in hundredths of a second.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.326.2.2.2.1.1.6 |
switchCDVThe switch Cell Delay Variation (CDV) specified in microseconds, indicates the time window in which a cell may be received on a connection and be accepted. A cell that is received on a connection outside the CDV window will be tagged or dropped as indicated by the switchPolicingAction object. The switchCDV is the default CDV for all the connections on this switch. Individual connections can be set to explicitly override this value.rwobsolete Integer32 .1.3.6.1.4.1.326.2.2.2.1.1.7 |
switchPolicingActionThis object indicates the action the switch will take in case of bandwidth violation. The switchPolicingAction is the default policing action for all the connections on this switch. Individual connections can be set to explicitly override this default action.rwobsolete Enumeration .1.3.6.1.4.1.326.2.2.2.1.1.8 |
softwareVersionTextThe version of the ATM switch control software. This object provides text information about the internal software configuration that was used when the switch control software was built.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.1.9 |
switchTypeThis object identifies the switch type.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.1.10 |
switchReservedPMPMinVCIThe minimum VCI that is reserved for PMP connections.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.1.12 |
switchReservedPMPMaxVCIThe maximum VCI that is reserved for PMP connections.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.1.13 |
switchTimeZoneThe TimeZone configured for this ATM switch. This variable follows the POSIX standard 1003.1-1988 for the format of the TZ environment variable. In particular, it is general enough to specify the rules for converting from Standard to Daylight Savings time for most timezones of the world. By default, the switch has the rules built in for the following timezones: EST5EDT CST6CDT MST7MDT PST8PDT AKST9AKDT. Locales outside of these timezones will need to supply the appropriate rule for switching between Daylight and Standard time.rw DisplayString .1.3.6.1.4.1.326.2.2.2.1.1.14 |
switchGMTimeThe switch's notion of Greenwich Mean Time. Linked to hrSystemDate. Offset part of time spec, if supplied, is considered an error.rw DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.1.15 |
switchProtocolTypeThe transfer protocol that is used when upgrading the switch software, backing up the CDB, etc.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.1.16 |
switchCurrentUseridThe value of this object identifies the user currently logged in or attempting to log in on the switch. It would be a NULL string if no one is logged in currently.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.1.17 |
switchCurrentLoginFromThis string gives the IP address of the host from where the current user is logged in or attempting to log in. A NULL string is returned if no one is currently logged in on the switch. If its a serial port login, the string indicates the samero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.1.18 |
switchPrimaryClockThe port number whose 8KHz clock is used as primary clock by all the netmods on all the boards in this switch.rwdeprecated Integer32 .1.3.6.1.4.1.326.2.2.2.1.1.19 |
switchSecondaryClockThe port number whose 8KHz clock is used as secondary clock by all the netmods on all the boards in this switch.rwdeprecated Integer32 .1.3.6.1.4.1.326.2.2.2.1.1.20 |
switchClockOperStatusThe currently active 8KHz clock configuration. The crystal?Clock types are not currently used. The default mode is localCrystalClock which means each netmod runs off of its own crystal. If primary, secondary or tcm clocking is configured then the status will be updated by switch software accordingly.rodeprecated Enumeration .1.3.6.1.4.1.326.2.2.2.1.1.21 |
switchTimingModeThe timing mode in which the switch is running. switchMode(1) provides for the direct use of any port recovered clock from any timing-capable network module in the switch. tcmMode(3) uses the clock provided by the CEC-Plus' Timing Control Modules (TCM).rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.1.22 |
switchConnectionPreservationWhen connection preservation is enabled the switch will not reset the hardware when a fail-over or software-reboot occurs. The software will preserve existing PVC connections and re-create other connections. This prevents cell traffic on PVC connections from being disrupted during the fail-over / software-reboot process. When connection preservation is disabled the switch will reset the hardware when a fail-over or software-reboot occurs. All connections will then be re-created. Cell traffic on all connections will be disrupted during the fail-over / software-reboot process. This is disabled by default on all asx200bx based switches. On all the other platforms, this is enabled by default.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.1.23 |
switchATMLayerOAMThis object specifies whether the processing of ATM layer OAM cells by this switch is enabled or disabled.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.1.24 |
switchHttpServerThis specifies whether the embedded HTTP Server (which is used for the element manager) is enabled or disabled.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.1.25 |
switchHttpHelpUrlThis specifies the URL path for the local depository of the WWW help pages for the web-based element manager on the switch. The URL is in the form: <ipaddress>[:port][<pathname>] For example: 1.2.3.4:8000/usr/fore/www This includes the IP address host to contact, and optionally the port on that host, and the directory on that host where the help pages were saved. If an empty string, the switch will use a default location on FORE's external web site.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.1.26 |
mcastGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.1.27 |
mcastSpaceTableA table containing information on number of multicast connections supported on this switch. SEQUENCE OF McastSpaceEntry .1.3.6.1.4.1.326.2.2.2.1.1.27.1 |
mcastSpaceEntryA table entry containing multicast space information McastSpaceEntry .1.3.6.1.4.1.326.2.2.2.1.1.27.1.1 |
mcastSpaceIndexIndex of this multicast space entry. This value is used to set boardMcastIndex value. Integer32 .1.3.6.1.4.1.326.2.2.2.1.1.27.1.1.1 |
mcastSpaceNumConnNumber of multicast connections that this entry represents. When boardMcastIndex is set to mcastSpaceIndex value, the corresponding board will support mcastSpaceNumConn number of multicast connections.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.1.27.1.1.2 |
mcastSpaceNameName of this multicast space entry.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.1.27.1.1.3 |
switchCtrlLinkidThe linkid of the ctrl port on this switch.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.1.28 |
switchClockCurrentStatusThe currently active 8KHz clock configuration. The value would indicate primary Clock or secondary Clock or if neither is available a <netmod> crystal Clock is determined by the switch control software. The software chooses the lowest netmod number with timing supportro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.1.29 |
switchDebounceTableA table, where each entry consists of debounce information associated with a unique port. This information includes the hysteresis value (a positive number in ms) for that port, i.e, the number of ms for which a physical-level failure persists for that port, after which the connection will be brought down SEQUENCE OF SwitchDebounceEntry .1.3.6.1.4.1.326.2.2.2.1.1.30 |
switchDebounceEntryA table entry containing physical interface debounce information. SwitchDebounceEntry .1.3.6.1.4.1.326.2.2.2.1.1.30.1 |
switchDebounceIndexThe index value for this entry - ties in with a unique portro Integer32 .1.3.6.1.4.1.326.2.2.2.1.1.30.1.1 |
switchDebounceNameThe persistent name of this interface - (the port name)ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.1.30.1.2 |
switchDebounceHysteresisThe hysteresis value for this interface. The hysteresis value is the number of ms for which a physical-level failure persists for that interface, after which the connection will be brought downrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.1.30.1.3 |
softwareLicenseKeyThe software license key of this switch.rw DisplayString .1.3.6.1.4.1.326.2.2.2.1.1.31 |
switchCounterResetTimeIndicates when all switch (except for virtual connection) counters were reset. The TimeStamp is equal to the sysUpTime when the reset occurred. If switch counters have never been reset, the switchCounterResetTime will be zero. This variable is updated whenever switchCounterReset is written.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.1.32 |
switchCounterResetWriting a value of resetRequest will result in a reset of all counters on the switch except for VCC indexed counters. Writing a value of unresetRequest will destroy all counter offsets and restore counter values to what has accumulated over the sysUpTime period. A response value of resetTrue indicates a resetRequest succeeded and is in effect. A response of resetFalse indicates a reset is not currently in effect.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.1.33 |
switchSbprServerAddressTableA table, where each entry consists of a static list of 5 bootp address entries. SEQUENCE OF SwitchSbprServerAddressEntry .1.3.6.1.4.1.326.2.2.2.1.1.34 |
switchSbprServerAddressEntryA bootp Ip Address server entry. SwitchSbprServerAddressEntry .1.3.6.1.4.1.326.2.2.2.1.1.34.1 |
sbprServerAddressIndexA unique value greater then zero used as an index into the bootp address table.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.1.34.1.1 |
sbprServerAddressIndexNameName of the Interface index into the bootp address table.rw DisplayString .1.3.6.1.4.1.326.2.2.2.1.1.34.1.2 |
sbprServerMaxHopsThe maximum number of hops that a BOOTREQUEST message is permitted to traverse before it must be discarded. Received BOOTREQUEST messages that have a hopcount greater than this value are discarded by this relay agent. The default value is 4.rw INTEGER .1.3.6.1.4.1.326.2.2.2.1.1.34.1.3 |
sbprServerMinSecondsThe minimum number of seconds that a BOOTP client must have been attempting to boot before the relay agent will relay BOOTREQUESTs from that client. The default value is 0.rw INTEGER .1.3.6.1.4.1.326.2.2.2.1.1.34.1.4 |
sbprServerAddress1The IP address of the BOOTP server.rw IpAddress .1.3.6.1.4.1.326.2.2.2.1.1.34.1.5 |
sbprServerAddress2The IP address of the BOOTP server.rw IpAddress .1.3.6.1.4.1.326.2.2.2.1.1.34.1.6 |
sbprServerAddress3The IP address of the BOOTP server.rw IpAddress .1.3.6.1.4.1.326.2.2.2.1.1.34.1.7 |
sbprServerAddress4The IP address of the BOOTP server.rw IpAddress .1.3.6.1.4.1.326.2.2.2.1.1.34.1.8 |
sbprServerAddress5The IP address of the BOOTP server.rw IpAddress .1.3.6.1.4.1.326.2.2.2.1.1.34.1.9 |
sbprServerRowStatusAdministrative status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.1.34.1.10 |
switchPrimaryClockPortThe name of the hardware port whose 8KHz clock is used as primary clock by all the netmods on all the boards in this switch.rw DisplayString .1.3.6.1.4.1.326.2.2.2.1.1.35 |
switchSecondaryClockPortThe name of the hardware port whose 8KHz clock is used as secondary clock by all the netmods on all the boards in this switch.rw DisplayString .1.3.6.1.4.1.326.2.2.2.1.1.36 |
serviceCategoryTableA table of ATM service categories supported. SEQUENCE OF ServiceCategoryEntry .1.3.6.1.4.1.326.2.2.2.1.1.37 |
serviceCategoryEntryA table entry containing ATM Service Category information. ServiceCategoryEntry .1.3.6.1.4.1.326.2.2.2.1.1.37.1 |
serviceCategoryIndexThe ATM service category index.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.1.37.1.1 |
serviceCategoryNameThe name of the ATM service category. The following values are supported: serviceCategoryIndex serviceCategoryName ----------------- ---------------------- 1 CBR 2 rtVBR 3 nrtVBR 4 ABR 5 UBRro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.1.37.1.2 |
switchPmpEnableDisabling the PMP Feature disallows any point to multipoint connections. The services which require point to multi point connections also need to be disabled. By default the feature is enabled.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.1.38 |
switchCallPreservationWhen SVx/SPVx Preservation is enabled, existing switched connections will be preserved during transfers of switch control from the Active SCP to the Standby SCP, whether user-initiated or due to SCP failure. Cell traffic is preserved during the failover/switchover process. When SVx/SPVx Preservation is disabled, and if Connection Preservation also is disabled, control transfers from the Active SCP to the Standby SCP will reset the switch hardware without having preserved the necessary call-state information. Hence, all switched connections will be cleared and will then have to be recreated. Cell traffic on all switched connections will be disrupted. By default, this feature is disabled on all supported dual-scp platforms.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.1.39 |
switchCallPresOperStatusWhen SVx/SPVx Preservation is enabled administratively, the feature nevertheless may be disabled operationally (e.g., because of hardware failures, like a missing Standby SCP). When it is operationally disabled, the effect is as though SVx/SPVx Preservation were disabled administratively.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.1.40 |
portGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.2 |
numberOfPortsThe number of ports on this ATM switch.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.2.1 |
portTableA table of information about the ports on this ATM switch. SEQUENCE OF PortEntry .1.3.6.1.4.1.326.2.2.2.1.2.2 |
portEntryA table entry containing port information. PortEntry .1.3.6.1.4.1.326.2.2.2.1.2.2.1 |
portNumberThe value of this object identifies the port.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.1 |
portAdminStatusThe desired state of this port. The up(3) state indicates that SPANS (Simple Protocol for ATM Network Signalling), FORE's link signalling protocol, is used to determine the operational status of the port. The down(2) state dictates that the operational status of the port should not be determined by SPANS.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.2.2.1.2 |
portOperStatusThe current operational state of this port, as determined either by administrative action, when the value of portAdminStatus is down(2), or by SPANS (Simple Protocol for ATM Network Signalling), FORE's link signalling protocol, when the value of porAdminStatus is up(3). For FRAM netmod, it is equivalent to the ifOperStatus of the same portro Enumeration .1.3.6.1.4.1.326.2.2.2.1.2.2.1.3 |
portTimeThe length of time this port has been in its current state, in hundredths of a second.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.326.2.2.2.1.2.2.1.4 |
portRemoteAtmAddressThe ATM address of the entity connected to this port.ro SpansAddress .1.3.6.1.4.1.326.2.2.2.1.2.2.1.5 |
portRemoteIpAddressThe IP address of the entity connected to this port.ro IpAddress .1.3.6.1.4.1.326.2.2.2.1.2.2.1.6 |
portMaxPathsInThe maximum number of incoming virtual paths supported by this port.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.7 |
portNumPathsInThe number of incoming virtual paths on this port.ro Gauge32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.8 |
portMaxBandwidthInThe maximum incoming bandwidth of this port, in cells per second.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.9 |
portAllocBandwidthInThe allocated incoming bandwidth of this port, in cells per second.ro Gauge32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.10 |
portUsedBandwidthInThe incoming bandwidth being used on this port, in cells per second.rodeprecated Gauge32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.11 |
portReceivedCellsThe number of cells received on this port.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.12 |
portMaxPathsOutThe maximum number of outgoing virtual paths supported by this port.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.13 |
portNumPathsOutThe number of outgoing virtual paths on this port.ro Gauge32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.14 |
portMaxBandwidthOutThe maximum outgoing bandwidth of this port, in cells per second.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.15 |
portAllocBandwidthOutThe allocated outgoing bandwidth of this port, in cells per second.ro Gauge32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.16 |
portUsedBandwidthOutThe outgoing bandwidth being used on this port, in cells per second.rodeprecated Gauge32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.17 |
portTransmittedCellsThe number of cells transmitted on this port.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.18 |
portHwBoardThe hardware board number of this port.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.19 |
portHwModuleThe hardware module number of this port. For a control port (a software port), the value of this object is the maximun number of hardware modules plus one.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.20 |
portHwNumberThe hardware port number of this port. For a control port (a software port), the value of this object is 0.rodeprecated Integer32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.21 |
portILMIRemoteIpAddressThe IP address of the entity connected to this port that was discovered using ILMI on path 0. If there is no q2931 siganlling path on VPI 0 that uses ILMI, the value of this object is 255.255.255.255.ro IpAddress .1.3.6.1.4.1.326.2.2.2.1.2.2.1.22 |
portCDVTThe Cell Delay Variation Tolerance associated with this physical port. Connections take their default value for CDVT from the input side port.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.23 |
portInputPolicingStatusThe state of policing on this input port. Enabled(1) forces every connection on this input port to be policed. Disabled(2) turns policing off for every connection on this input port. The functions of this variable have been subsumed by the new GCRAPolicingCBR and GCRAPolicingVBR variables below. Now, writing 'disabled' to this MIB variable has the effect of setting GCRAPolicingCBR=allOff and GCRAPolicingVBR=allOff. On read, this variable reports 'enabled', if either of the GCRAPolicing*BR options are in an 'On' setting. Use of this variable should be avoided, in favor of the two GCRA variables.rwdeprecated Enumeration .1.3.6.1.4.1.326.2.2.2.1.2.2.1.24 |
portVbrOverbookingThe percentage of overbooking for nrtVBR connections. The default value is 100 (no overbooking).rwdeprecated INTEGER .1.3.6.1.4.1.326.2.2.2.1.2.2.1.25 |
portVbrBufferOverbThe percentage of buffer overbooking for nrtVBR connections. The default value is 100 (no overbooking).rwdeprecated INTEGER .1.3.6.1.4.1.326.2.2.2.1.2.2.1.26 |
portManagementStatusThe visibility of this port in the management station's view. The default value is 1 (managed).rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.2.2.1.27 |
portAISRDIGenerationThe port ATM layer AIS and RDI generation status.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.2.2.1.28 |
portGCRAPolicingCBRThis variable defines the per-port policing configuration for CBR connections. The states mean the following: allOn: ALL CBR connections arriving on this port will be subjected to GCRA policing. allOff: NO CBR connections arriving on this port will be subjected to GCRA policing. svcOn: ALL CRB SVCs arriving on this port will be subjected to GCRA policing svcOff: NO CBR SVCs arriving on this port will be subjected to GCRA policing. CBR PVCs will be GCRA policed based on the state of their UPC contract. default: ALL CBR UNI SVCs/SVPs arriving at this port will be subject to GCRA policing and NO CBR NNI SVCs/SVPs arriving at this port will be subject to GCRA policing. CBR PVCs/PVPs arriving at this port will be policed based on the state of their UPC contract.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.2.2.1.33 |
portGCRAPolicingVBRThis variable defines the per-port policing configuration for nrtVBR connections. The states mean the following: allOn: ALL nrtVBR connections arriving on this port will be subjected to GCRA policing. allOff: NO nrtVBR connections arriving on this port will be subjected to GCRA policing. svcOn: ALL nrtVBR SVCs arriving on this port will be subjected to GCRA policing svcOff: NO nrtVBR SVCs arriving on this port will be subjected to GCRA policing. nrtVBR PVCs will be GCRA policed based on the state of their UPC contract. default: ALL nrtVBR UNI SVCs/SVPs arriving at this port will be subject to GCRA policing and NO nrtVBR NNI SVCs/SVPs arriving at this port will be subject to GCRA policing. nrtVBR PVCs/PVPs arriving at this port will be policed based on the state of their UPC contract.rwdeprecated Enumeration .1.3.6.1.4.1.326.2.2.2.1.2.2.1.34 |
portAAL5PacketDiscardCBRThis variable defines the per-port AAL5 packet discard configuration for CBR connections. The states mean the following: allOn: All CBR AAL5 connections have packet discard performed on them. allOff: AAL5 packet discard is not performed on any CBR connections. svcOn: Any CBR SVC that 'requests' packet discard will have it performed. For CBR PVC's, AAL5 packet discard is enabled based on the UPC contract of the connection. svcOff: AAL5 packet discard is not performed on any CBR SVC's.For CBR PVC's, AAL5 packet discard is enabled based on the UPC contract of the connection.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.2.2.1.35 |
portAAL5PacketDiscardVBRThis variable defines the per-port AAL5 packet discard configuration for nrtVBR connections. The states mean the following: allOn: All nrtVBR AAL5 connections have packet discard performed on them. allOff: AAL5 packet discard is not performed on any nrtVBR connections. svcOn: Any nrtVBR SVC that 'requests' packet discard will have it performed. For nrtVBR PVC's, AAL5 packet discard is enabled based on the UPC contract of the connection. svcOff: AAL5 packet discard is not performed on any nrtVBR SVC's.For nrtVBR PVC's, AAL5 packet discard is enabled based on the UPC contract of the connection.rwdeprecated Enumeration .1.3.6.1.4.1.326.2.2.2.1.2.2.1.36 |
portAAL5PacketDiscardUBRThis variable defines the per-port AAL5 packet discard configuration for UBR connections. The states mean the following: allOn: All UBR AAL5 connections have packet discard performed on them. allOff: AAL5 packet discard is not performed on any UBR connections. svcOn: Any UBR SVC that 'requests' packet discard will have it performed. For UBR PVC's, AAL5 packet discard is enabled based on the UPC contract of the connection. svcOff: AAL5 packet discard is not performed on any UBR SVC's.For UBR PVC's, AAL5 packet discard is enabled based on the UPC contract of the connection.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.2.2.1.37 |
portInputCACErrorsThe number of input CAC (Call Admission Control) failures on this port.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.38 |
portInputVPIErrorsThe number of input VPI allocation failures on this port.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.39 |
portInputVCIErrorsThe number of input VCI allocation failures on this port.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.40 |
portInputSetupErrorsThe number of input connection setup failures on this port.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.41 |
portOutputCACErrorsThe number of output CAC (Call Admission Control) failures on this port.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.42 |
portOutputVPIErrorsThe number of output VPI allocation failures on this port.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.43 |
portOutputVCIErrorsThe number of output VCI allocation failures on this port.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.44 |
portOutputSetupErrorsThe number of output connection setup failures on this port.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.45 |
portPPPolicingCBRThis variable defines the per-port AAL5 Partial Packet Policing configuration for CBR connections. The states of this variable mean the following: allOn: All CBR AAL5 connections have partial packet policing performed on them. allOff: AAL5 partial packet policing is not performed on any CBR connections. svcOn: Any CBR SVC that uses AAL5 will have partial packet policing performed on it. For CBR PVC's, partial packet policing will be performed based on the UPC contract of the connection. svcOff: Partial packet policing will not be performed on any CBR SVC's. For CBR PVC's, partial packet policing is enabled based on the UPC contract of the connection.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.2.2.1.46 |
portPPPolicingVBRThis variable defines the per-port AAL5 Partial Packet Policing configuration for nrtVBR connections. The states of this variable mean the following: allOn: All nrtVBR AAL5 connections have partial packet policing performed on them. allOff: AAL5 partial packet policing is not performed on any nrtVBR connections. svcOn: Any nrtVBR SVC that uses AAL5 will have partial packet policing performed on it. For nrtVBR PVC's, partial packet policing will be performed based on the UPC contract of the connection. svcOff: Partial packet policing will not be performed on any nrtVBR SVC's. For nrtVBR PVC's, partial packet policing is enabled based on the UPC contract of the connection.rwdeprecated Enumeration .1.3.6.1.4.1.326.2.2.2.1.2.2.1.47 |
portUBRTaggingThis variable defines the per-port configuration for tagging (setting CLP=1) of all cells on UBR connections. The states of this variable mean the following: allOn: All UBR connections will be tagged. allOff: No UBR connections will be subject to tagging. svcOn: All UBR SVC's will be tagged. UBR PVC's will be tagged based on their UPC contract. svcOff: No UBR SVC's will be tagged. UBR PVC's will be tagged based on their UPC contract.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.2.2.1.48 |
portInputCdvThe current value of Cell Delay Variation attributed to the input side of this port, which can be either a user specified value or the system default, as determined by the setting of portInputCdvMode.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.49 |
portInputMaxctdThis variable give the maximum Cell Transfer Delay that is being attributed to the input side of this port. The value can be either user specified or a hardware dependant system default value.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.50 |
portInputDelayModeThis variable controls whether the Cell Delay Variation and Maximum Cell Transfer Delay values attributed to the input side of this port are based on a user defined value or the hardware dependant system default values.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.2.2.1.51 |
portOutputCdvIf portOutputDelayMode == userSpecified then this variable contains the constant amount of Cell Delay Variation that is being attributed to this output port. If portOutputDelayMode == systemDefault then an actual value for the Cell Delay Variation experienced by connections traversing this port is being calculated. In this case the value of this variable is meaningless since CDV can only be calculated on a per-connection basis.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.52 |
portOutputMaxctdThis variable gives the maximum Cell Transfer Delay that is being attributed to the output side of this port. The value can be either user specified or a hardware dependant system default value.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.2.2.1.53 |
portOutputDelayModeThis variable controls whether the Cell Delay Variation value contributed by the input side of this port is based on a user defined value or the system default value.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.2.2.1.54 |
portCACStatusThe enforcement state of call admission control. The default is enabled(1).rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.2.2.1.59 |
portCounterResetTimeIndicates when this port's counters were reset. The TimeStamp is equal to moduleUptime when the reset occurred. If this ports counters were never reset, portCounterResetTime will be zero. This variable is updated whenever portCounterReset or switchCounterReset is written.rodeprecated TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.2.2.1.60 |
portCounterResetWriting a value of resetRequest will result in a reset of all counters on this port. VCC indexed counters are excluded. A response value of resetTrue indicates a resetRequest has succeeded and is currently in effect. A response value of resetFalse indicates a reset is not currently in effect.rwdeprecated Enumeration .1.3.6.1.4.1.326.2.2.2.1.2.2.1.61 |
portNameThe name of this port (BNP format or otherwise).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.2.2.1.62 |
portGCRAPolicingRTVBRThis variable defines the per-port policing configuration for rtVBR connections. The states mean the following: allOn: ALL rtVBR connections arriving on this port will be subjected to GCRA policing. allOff: NO rtVBR connections arriving on this port will be subjected to GCRA policing. svcOn: ALL rtVBR SVCs arriving on this port will be subjected to GCRA policing svcOff: NO rtVBR SVCs arriving on this port will be subjected to GCRA policing. rtVBR PVCs will be GCRA policed based on the state of their UPC contract. default: ALL rtVBR UNI SVCs/SVPs arriving at this port will be subject to GCRA policing and NO rtVBR NNI SVCs/SVPs arriving at this port will be subject to GCRA policing. rtVBR PVCs/PVPs arriving at this port will be policed based on the state of their UPC contract.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.2.2.1.64 |
portGCRAPolicingNRTVBRThis variable defines the per-port policing configuration for nrtVBR connections. The states mean the following: allOn: ALL nrtVBR connections arriving on this port will be subjected to GCRA policing. allOff: NO nrtVBR connections arriving on this port will be subjected to GCRA policing. svcOn: ALL nrtVBR SVCs arriving on this port will be subjected to GCRA policing svcOff: NO nrtVBR SVCs arriving on this port will be subjected to GCRA policing. nrtVBR PVCs will be GCRA policed based on the state of their UPC contract. default: ALL nrtVBR UNI SVCs/SVPs arriving at this port will be subject to GCRA policing and NO nrtVBR NNI SVCs/SVPs arriving at this port will be subject to GCRA policing. nrtVBR PVCs/PVPs arriving at this port will be policed based on the state of their UPC contract.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.2.2.1.65 |
portAAL5PacketDiscardRTVBRThis variable defines the per-port AAL5 packet discard configuration for rtVBR connections. The states mean the following: allOn: All rtVBR AAL5 connections have packet discard performed on them. allOff: AAL5 packet discard is not performed on any rtVBR connections. svcOn: Any rtVBR SVC that 'requests' packet discard will have it performed. For rtVBR PVC's, AAL5 packet discard is enabled based on the UPC contract of the connection. svcOff: AAL5 packet discard is not performed on any rtVBR SVC's.For rtVBR PVC's, AAL5 packet discard is enabled based on the UPC contract of the connection.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.2.2.1.66 |
portAAL5PacketDiscardNRTVBRThis variable defines the per-port AAL5 packet discard configuration for nrtVBR connections. The states mean the following: allOn: All nrtVBR AAL5 connections have packet discard performed on them. allOff: AAL5 packet discard is not performed on any nrtVBR connections. svcOn: Any nrtVBR SVC that 'requests' packet discard will have it performed. For nrtVBR PVC's, AAL5 packet discard is enabled based on the UPC contract of the connection. svcOff: AAL5 packet discard is not performed on any nrtVBR SVC's.For nrtVBR PVC's, AAL5 packet discard is enabled based on the UPC contract of the connection.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.2.2.1.67 |
portPPPolicingNRTVBRThis variable defines the per-port AAL5 Partial Packet Policing configuration for nrtVBR connections. The states of this variable mean the following: allOn: All nrtVBR AAL5 connections have partial packet policing performed on them. allOff: AAL5 partial packet policing is not performed on any nrtVBR connections. svcOn: Any nrtVBR SVC that uses AAL5 will have partial packet policing performed on it. For nrtVBR PVC's, partial packet policing will be performed based on the UPC contract of the connection. svcOff: Partial packet policing will not be performed on any nrtVBR SVC's. For nrtVBR PVC's, partial packet policing is enabled based on the UPC contract of the connection.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.2.2.1.68 |
portPPPolicingRTVBRThis variable defines the per-port AAL5 Partial Packet Policing configuration for rtVBR connections. The states of this variable mean the following: allOn: All rtVBR AAL5 connections have partial packet policing performed on them. allOff: AAL5 partial packet policing is not performed on any rtVBR connections. svcOn: Any rtVBR SVC that uses AAL5 will have partial packet policing performed on it. For rtVBR PVC's, partial packet policing will be performed based on the UPC contract of the connection. svcOff: Partial packet policing will not be performed on any rtVBR SVC's. For rtVBR PVC's, partial packet policing is enabled based on the UPC contract of the connection.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.2.2.1.69 |
portNrtVbrOverbookingThe percentage of overbooking for nrtVBR connections. The default value is 100 (no overbooking).rw INTEGER .1.3.6.1.4.1.326.2.2.2.1.2.2.1.70 |
portNrtVbrBufferOverbThe percentage of buffer overbooking for nrtVBR connections. The default value is 100 (no overbooking).rw INTEGER .1.3.6.1.4.1.326.2.2.2.1.2.2.1.71 |
portRtVbrOverbookingThe percentage of overbooking for rtVBR connections. The default value is 100 (no overbooking).rw INTEGER .1.3.6.1.4.1.326.2.2.2.1.2.2.1.72 |
portRtVbrBufferOverbThe percentage of buffer overbooking for rtVBR connections. The default value is 100 (no overbooking).rw INTEGER .1.3.6.1.4.1.326.2.2.2.1.2.2.1.73 |
portPathOverbookingThe percentage of overbooking for inelastic originating paths. The default value is 100 (no overbooking).rw INTEGER .1.3.6.1.4.1.326.2.2.2.1.2.2.1.74 |
atmIfConnSchedTableA table of connection scheduling information on this ATM If. SEQUENCE OF AtmIfConnSchedEntry .1.3.6.1.4.1.326.2.2.2.1.2.3 |
atmIfConnSchedEntryA table of connection scheduling information on this ATM If. AtmIfConnSchedEntry .1.3.6.1.4.1.326.2.2.2.1.2.3.1 |
atmIfConnSchedLinkThe index of this ATM If. Integer32 .1.3.6.1.4.1.326.2.2.2.1.2.3.1.1 |
atmIfConnSchedServCatIndex of this service category within serviceCategoryTable. Integer32 .1.3.6.1.4.1.326.2.2.2.1.2.3.1.2 |
atmIfConnSchedModeThe scheduling mode used for connections of type atmIfConnSchedServCat on this ATM if. The default choice of AtmConnSchedMode is not allowed at atmIf level.rw AtmConnSchedMode .1.3.6.1.4.1.326.2.2.2.1.2.3.1.3 |
atmIfConnSchedOverrideThe override option used for connections of type atmIfConnSchedServCat on this ATM if.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.2.3.1.4 |
pathGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.3 |
pathTableA table of information about the virtual paths passing through this ATM switch. SEQUENCE OF PathEntry .1.3.6.1.4.1.326.2.2.2.1.3.1 |
pathEntryA table entry containing path information. PathEntry .1.3.6.1.4.1.326.2.2.2.1.3.1.1 |
pathPortThe value of this object identifies the input port of this path and is the same as the portNumber.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.1.1.1 |
pathVPIThe input VPI (Virtual Path Identifier) of this path.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.1.1.2 |
pathStatusThe status of this path entry.rw EntryStatus .1.3.6.1.4.1.326.2.2.2.1.3.1.1.3 |
pathNumOutputsThe number of output ports to which this path is routed.ro Gauge32 .1.3.6.1.4.1.326.2.2.2.1.3.1.1.4 |
pathMaxChannelsThe maximum number of virtual channels that can be allocated on this path.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.1.1.5 |
pathNumChannelsThe number of virtual channels currently allocated on this path.ro Gauge32 .1.3.6.1.4.1.326.2.2.2.1.3.1.1.6 |
pathMaxBandwidthThe maximum bandwidth of this path, in cells per second.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.1.1.7 |
pathAllocBandwidthThe allocated bandwidth of this path, in cells per second.rw Gauge32 .1.3.6.1.4.1.326.2.2.2.1.3.1.1.8 |
pathUsedBandwidthThe bandwidth being used on this path, in cells per second.rodeprecated Gauge32 .1.3.6.1.4.1.326.2.2.2.1.3.1.1.9 |
pathCellsThe number of cells transferred over this path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.3.1.1.10 |
pathUptimeThe time since this path was created, in hundredths of a second.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.326.2.2.2.1.3.1.1.11 |
pathSigProtocolThe signaling protocol that created this path.ro AtmSigProtocol .1.3.6.1.4.1.326.2.2.2.1.3.1.1.12 |
pathRejectedCellsThe number of cells over this path that were rejected (i.e. dropped) by the policer on the switch fabric. This does not include any cells that may have been tagged with CLP=1 by the policer, only cells that were discarded.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.3.1.1.13 |
pathMinVCIThe minimum VCI that can be allocated on this path.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.1.1.14 |
pathMaxVCIThe maximum VCI that can be allocated on this path.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.1.1.15 |
pathCACErrorsThe number of CAC (Call Admission Control) failures on this path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.3.1.1.16 |
pathVCIErrorsThe number of VCI allocation failures on this path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.3.1.1.17 |
pathSetupErrorsThe number of connection setup failures on this path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.3.1.1.18 |
pathRouteTableA table of information about the routing of paths through this ATM switch. SEQUENCE OF PathRouteEntry .1.3.6.1.4.1.326.2.2.2.1.3.2 |
pathRouteEntryA table entry containing path route information. PathRouteEntry .1.3.6.1.4.1.326.2.2.2.1.3.2.1 |
pathrInputPortThe value of this object identifies the input port of this path and is the same as the portNumber.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.2.1.1 |
pathrInputVPIThe input VPI (Virtual Path Identifier) of this path.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.2.1.2 |
pathrOutputPortThe value of this object identifies the output port of this path and is the same as the portNumber.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.2.1.3 |
pathrOutputVPIThe output VPI (Virtual Path Identifier) of this path.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.2.1.4 |
pathrStatusThe status of this path entry.rw EntryStatus .1.3.6.1.4.1.326.2.2.2.1.3.2.1.5 |
pathrMaxBandwidthThe maximum bandwidth of this path, in cells per second.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.2.1.6 |
pathrAllocBandwidthThe allocated bandwidth of this path, in cells per second.rw Gauge32 .1.3.6.1.4.1.326.2.2.2.1.3.2.1.7 |
pathrCellsThe number of cells transferred over this path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.3.2.1.8 |
pathrUptimeThe time since this path was created, in hundredths of a second.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.326.2.2.2.1.3.2.1.9 |
pathrSigProtocolThe signaling protocol that created this path.ro AtmSigProtocol .1.3.6.1.4.1.326.2.2.2.1.3.2.1.10 |
pathrRejectedCellsThe number of cells over this through path that were rejected (i.e. dropped) by the policer on the switch fabric. This does not include any cells that may have been tagged with CLP=1 by the policer, only cells that were discarded.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.3.2.1.11 |
pathrLoopVPIIf this value is other than -1, cells destined for pathrOutputPort, pathrOutputVPI will be translated by the netmod to pathrLoopVPI before actually being trasmitted. This was instituted to facilitate single port loopback.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.2.1.12 |
pathrUpcContractThe UPC contract that will be used to police this through path. This is the number of the row in the upcContractTable.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.2.1.13 |
pathrNameThe value of this object identifies the name that has been assigned for this path.rw OCTET STRING .1.3.6.1.4.1.326.2.2.2.1.3.2.1.14 |
pathrConnectionTypeThis object identifies the type of the path endpoints with respect to a particular network.rw ConnectionType .1.3.6.1.4.1.326.2.2.2.1.3.2.1.15 |
pathrServCatIndex of this service category within serviceCategoryTablero Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.2.1.16 |
outputPathTableA table of information about the virtual paths originating at this ATM switch. SEQUENCE OF OutputPathEntry .1.3.6.1.4.1.326.2.2.2.1.3.3 |
outputPathEntryA table entry containing output path information. OutputPathEntry .1.3.6.1.4.1.326.2.2.2.1.3.3.1 |
opathPortThe value of this object identifies the output port of this path and is the same as the portNumber.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.3.1.1 |
opathVPIThe VPI (Virtual Path Identifier) of this path.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.3.1.2 |
opathStatusThe status of this path entry.rw EntryStatus .1.3.6.1.4.1.326.2.2.2.1.3.3.1.3 |
opathMaxChannelsThe maximum number of virtual channels that can be allocated on this path.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.3.1.4 |
opathNumChannelsThe number of virtual channels currently allocated on this path.ro Gauge32 .1.3.6.1.4.1.326.2.2.2.1.3.3.1.5 |
opathMaxBandwidthThe maximum bandwidth of this path, in cells per second.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.3.1.6 |
opathAllocBandwidthThe allocated bandwidth of this path, in cells per second.rw Gauge32 .1.3.6.1.4.1.326.2.2.2.1.3.3.1.7 |
opathUsedBandwidthThe bandwidth used on this path, in cells per second.rodeprecated Gauge32 .1.3.6.1.4.1.326.2.2.2.1.3.3.1.8 |
opathCellsThe number of cells transmitted on this path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.3.3.1.9 |
opathUptimeThe time since this path was created, in hundredths of a second.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.326.2.2.2.1.3.3.1.10 |
opathSigProtocolThe signaling protocol that created this path.ro AtmSigProtocol .1.3.6.1.4.1.326.2.2.2.1.3.3.1.11 |
opathRejectedCellsThe number of cells on this output path that were rejected (i.e. dropped) by the policer on the switch fabric. This does not include any cells that may have been tagged with CLP=1 by the policer, only cells that were discarded.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.3.3.1.12 |
opathTrafficShapeVPIThe VPI of shaped cellsrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.3.1.13 |
opathVbrOverbookingThe percentage of overbooking for nrtVBR connections. The default value is 100 (no overbooking). A value of -1 indicates that the path is elastic, and therefore the overbooking factors are meaningless.rwdeprecated INTEGER (-1..32767) .1.3.6.1.4.1.326.2.2.2.1.3.3.1.14 |
opathVbrBufferOverbThe percentage of buffer overbooking for nrtVBR connections. The default value is 100 (no overbooking). A value of -1 indicates that the path is elastic, and therefore the overbooking factors are meaningless.rwdeprecated INTEGER (-1..32767) .1.3.6.1.4.1.326.2.2.2.1.3.3.1.15 |
opathMinVCIThe minimum VCI that can be allocated on this path.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.3.1.16 |
opathMaxVCIThe maximum VCI that can be allocated on this path.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.3.1.17 |
opathCACErrorsThe number of CAC (Call Admission Control) failures on this path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.3.3.1.18 |
opathVCIErrorsThe number of VCI allocation failures on this path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.3.3.1.19 |
opathSetupErrorsThe number of connection setup failures on this path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.3.3.1.20 |
opathLoopVPIIf this value is assigned to other than -1, the netmod will modify cell headers received from the fabric that are destined for opathPort, opathVPI to have the vpi value of opathLoopVPI before being transmitted. This extra translation can be used to loop cells back onto the fabric using a single port.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.3.1.21 |
opathSchedModeThe value of this object identifies the scheduling mode for this originating path.rw AtmOrigPathSchedMode .1.3.6.1.4.1.326.2.2.2.1.3.3.1.22 |
opathNrtVbrOverbookingThe percentage of overbooking for nrtVBR connections. The default value is 100 (no overbooking). A value of -1 indicates that the path is elastic, and therefore the overbooking factors are meaningless.rw INTEGER (-1..32767) .1.3.6.1.4.1.326.2.2.2.1.3.3.1.23 |
opathNrtVbrBufferOverbThe percentage of buffer overbooking for nrtVBR connections. The default value is 100 (no overbooking). A value of -1 indicates that the path is elastic, and therefore the overbooking factors are meaningless.rw INTEGER (-1..32767) .1.3.6.1.4.1.326.2.2.2.1.3.3.1.24 |
opathRtVbrOverbookingThe percentage of overbooking for rtVBR connections. The default value is 100 (no overbooking). A value of -1 indicates that the path is elastic, and therefore the overbooking factors are meaningless.rw INTEGER (-1..32767) .1.3.6.1.4.1.326.2.2.2.1.3.3.1.25 |
opathRtVbrBufferOverbThe percentage of buffer overbooking for rtVBR connections. The default value is 100 (no overbooking). A value of -1 indicates that the path is elastic, and therefore the overbooking factors are meaningless.rw INTEGER (-1..32767) .1.3.6.1.4.1.326.2.2.2.1.3.3.1.26 |
outputPathStatsTableA table of statistics information about the virtual paths originating at this ATM switch. SEQUENCE OF OutputPathStatsEntry .1.3.6.1.4.1.326.2.2.2.1.3.4 |
outputPathStatsEntryA table entry containing originating channel statistics information. OutputPathStatsEntry .1.3.6.1.4.1.326.2.2.2.1.3.4.1 |
opathStatsPortThe value of this object identifies the output port of this channel and is the same as the opathPort, and portNumber.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.4.1.1 |
opathStatsVPIThe value of this object identifies the output VPI (Virtual Path Identifier) of this channel and is the same as the opathVPI.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.4.1.2 |
opathStatsLostCellsThe number of cells on this output path that were dropped at the output netmod.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.3.4.1.3 |
opathStatsTransmittedCellsThe number of cells on this output path that were transmitted.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.3.4.1.4 |
opathStatsIntentionalLostCellsThe number of cells on this output path that were dropped intentionally at the output netmod.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.3.4.1.5 |
opathStatsCLP0CellsThe number of CLP = 0 cells transmitted on this output path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.3.4.1.6 |
opathStatsLostPacketsThe number of packets on this output path that were dropped at the output netmod.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.3.4.1.7 |
opathStatsTransmittedPacketsThe number of Packets on this output path that were transmitted.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.3.4.1.8 |
outputPathChannelSchedTableA table of connection scheduling information on this output path. SEQUENCE OF OutputPathChannelSchedEntry .1.3.6.1.4.1.326.2.2.2.1.3.5 |
outputPathChannelSchedEntryA table of connection scheduling information on this output path. OutputPathChannelSchedEntry .1.3.6.1.4.1.326.2.2.2.1.3.5.1 |
opathChannelSchedPortIndex of this port Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.5.1.1 |
opathChannelSchedVPIThe value of this object identifies the output VPI (Virtual Path Identifier) of this path. Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.5.1.2 |
opathChannelSchedServCatIndex of this service category within serviceCategoryTable Integer32 .1.3.6.1.4.1.326.2.2.2.1.3.5.1.3 |
opathChannelSchedSchedModeThe scheduling mode used for channels of type opathChannelSchedServCat within this path. The default choice of AtmConnSchedMode is not allowed at path level.rw AtmConnSchedMode .1.3.6.1.4.1.326.2.2.2.1.3.5.1.4 |
opathChannelSchedSchedOverrideThe override option used for channels of type opathChannelSchedServCat within this pathrw Enumeration .1.3.6.1.4.1.326.2.2.2.1.3.5.1.5 |
channelGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.4 |
channelTableA table of information about the virtual channels passing through this ATM switch. SEQUENCE OF ChannelEntry .1.3.6.1.4.1.326.2.2.2.1.4.1 |
channelEntryA table entry containing channel information. ChannelEntry .1.3.6.1.4.1.326.2.2.2.1.4.1.1 |
chanPortThe value of this object identifies the input port of this channel and is the same as the pathPort and portNumber.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.4.1.1.1 |
chanVPIThe value of this object identifies the input VPI (Virtual Path Identifier) of this channel, and is the same as the pathVPI.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.4.1.1.2 |
chanVCIThe input VCI (Virtual Channel Identifier) of this channel.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.4.1.1.3 |
chanStatusThe status of this channel entry.rw EntryStatus .1.3.6.1.4.1.326.2.2.2.1.4.1.1.4 |
chanNumOutputsThe number of output ports to which this channel is routed.ro Gauge32 .1.3.6.1.4.1.326.2.2.2.1.4.1.1.5 |
chanAllocBandwidthThe allocated bandwidth of this channel, in cells per second.rw Gauge32 .1.3.6.1.4.1.326.2.2.2.1.4.1.1.6 |
chanUsedBandwidthThe bandwidth used on this channel, in cells per second.rodeprecated Gauge32 .1.3.6.1.4.1.326.2.2.2.1.4.1.1.7 |
chanCellsThe number of cells transferred on this channel.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.4.1.1.8 |
chanUptimeThe time since this channel was created, in hundredths of a second.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.326.2.2.2.1.4.1.1.9 |
chanSigProtocolThe signaling protocol that created this channel.ro AtmSigProtocol .1.3.6.1.4.1.326.2.2.2.1.4.1.1.10 |
chanRejectedCellsThe number of cells on this channel that were rejected (dropped) by the policer on the switch fabric. This does not include any cells that may have been tagged with CLP=1 by the policer, only cells that were discarded.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.4.1.1.11 |
chanCDVThe channel Cell Delay Variation Tolerance (CDV), specified in microseconds, indicates the time window in which a cell may be received on a channel and be accepted. A cell that is received on a channel outside the CDV window will be dropped or tagged, based on the value of chanPolicingAction. The chanCDV value overrides the default value inherited from the link.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.4.1.1.12 |
chanPolicingActionThis object indicates the action the switch will take in case of bandwidth violation on this channel.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.4.1.1.13 |
chanUpcContractThe UPC contract that will be used to police this channel. This is the number of the row in the upcContractTable.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.4.1.1.14 |
chanServCatIndex of this service category within serviceCategoryTablero Integer32 .1.3.6.1.4.1.326.2.2.2.1.4.1.1.15 |
chanQosPoliceSchemeIt identifies the policing associated with the UPC contract as defined in the ATM Forum TM 4.0 specifications. However, the policing schemes cbr0 and cbr0tag are specific to FORE switchesro Enumeration .1.3.6.1.4.1.326.2.2.2.1.4.1.1.16 |
chanQosPCRThe peak cell rate (cells/sec)ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.4.1.1.17 |
chanQosSCRThe sustained cell rate (cells/sec). It also holds the PCR0 value for cbr0 & cbr0tag contractsro Integer32 .1.3.6.1.4.1.326.2.2.2.1.4.1.1.18 |
chanQosMBSThe maximum burst size (cells)ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.4.1.1.19 |
chanQosCDVTThe channel Cell Delay Variation Tolerance (CDVT), specified in microseconds, indicates the time window in which a cell may be received on a channel and be accepted. A cell that is received on a channel outside the CDV window will be dropped or tagged, based on the value of chanPolicingAction. The chanCDV value overrides the default value inherited from the link.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.4.1.1.20 |
chanQosPoliceStateIndicates if this connection is policed for traffic violations. When set to 'on' it overrides the policing status of the atm interface on which this connection is established.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.4.1.1.21 |
chanQosIsAAL5Indicates if this connection is AAL 5ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.4.1.1.22 |
chanQosPerPacketPolicingShould we perform AAL5 Partial Packet Policing on this UPC contract. This variable only has meaning if the connections is also AAL5.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.4.1.1.23 |
channelRouteTableA table of information about the routing of channels through this ATM switch. SEQUENCE OF ChannelRouteEntry .1.3.6.1.4.1.326.2.2.2.1.4.2 |
channelRouteEntryA table entry containing channel route information. ChannelRouteEntry .1.3.6.1.4.1.326.2.2.2.1.4.2.1 |
chanrInputPortThe value of this object identifies the input port of this channel and is the same as the chanPort, pathPort, and portNumber.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.4.2.1.1 |
chanrInputVPIThe value of this object identifies the input VPI (Virtual Path Identifier) of this channel, and is the same as the chanVPI, and pathVPI.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.4.2.1.2 |
chanrInputVCIThe value of this object identifies the input VCI (Virtual Channel Identifier) of this channel, and is the same as chanVCI.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.4.2.1.3 |
chanrOutputPortThe value of this object identifies the output port of this channel and is the same as the opathPort, and portNumber.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.4.2.1.4 |
chanrOutputVPIThe value of this object identifies the output VPI (Virtual Path Identifier) of this channel and is the same as the opathVPI.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.4.2.1.5 |
chanrOutputVCIThe output VCI (Virtual Channel Identifier) of this channel.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.4.2.1.6 |
chanrStatusThe status of this channel entry.rw EntryStatus .1.3.6.1.4.1.326.2.2.2.1.4.2.1.7 |
chanrSigProtocolThe signaling protocol that created this channel.ro AtmSigProtocol .1.3.6.1.4.1.326.2.2.2.1.4.2.1.8 |
chanrNameThe value of this object identifies the name that has been assigned for this channel.rw OCTET STRING .1.3.6.1.4.1.326.2.2.2.1.4.2.1.9 |
chanrConnectionTypeThis object identifies the type of the channel endpoints with respect to a particular network.rw ConnectionType .1.3.6.1.4.1.326.2.2.2.1.4.2.1.10 |
reverseChannelRouteTableA table of information about reverse channel routes through this ATM switch. SEQUENCE OF ReverseChannelRouteEntry .1.3.6.1.4.1.326.2.2.2.1.4.3 |
reverseChannelRouteEntryA table entry containing reverse channel route information. ReverseChannelRouteEntry .1.3.6.1.4.1.326.2.2.2.1.4.3.1 |
revChanrOutputPortThe value of this object identifies the output port of this channel and is the same as the chanrOutputPort, opathPort and portNumber.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.4.3.1.1 |
revChanrOutputVPIThe value of this object identifies the output VPI (Virtual Path Identifier) of this channel and is the same as the chanrOutputVPI and opathVPI.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.4.3.1.2 |
revChanrOutputVCIThe output VCI (Virtual Channel Identifier) of this channel and is the same as chanrOutputVCI.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.4.3.1.3 |
revChanrInputPortThe value of this object identifies the input port of this channel and is the same as the chanPort, chanrInputPort, pathPort, and portNumber.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.4.3.1.4 |
revChanrInputVPIThe value of this object identifies the input VPI (Virtual Path Identifier) of this channel, and is the same as the chanVPI, chanrInputVPI and pathVPI.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.4.3.1.5 |
revChanrInputVCIThe value of this object identifies the input VCI (Virtual Channel Identifier) of this channel, and is the same as chanVCI and chanrInputVCI.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.4.3.1.6 |
revChanrSigProtocolThe signaling protocol that created this channel and is the same as chanrSigProtocol.ro AtmSigProtocol .1.3.6.1.4.1.326.2.2.2.1.4.3.1.7 |
outputChannelStatsTableA table of statistics information about the virtual channels originating at this ATM switch. SEQUENCE OF OutputChannelStatsEntry .1.3.6.1.4.1.326.2.2.2.1.4.4 |
outputChannelStatsEntryA table entry containing originating channel statistics information. OutputChannelStatsEntry .1.3.6.1.4.1.326.2.2.2.1.4.4.1 |
ochanStatsPortThe value of this object identifies the output port of this channel and is the same as the opathPort, and portNumber.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.4.4.1.1 |
ochanStatsVPIThe value of this object identifies the output VPI (Virtual Path Identifier) of this channel and is the same as the opathVPI.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.4.4.1.2 |
ochanStatsVCIThe output VCI (Virtual Channel Identifier) of this channel.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.4.4.1.3 |
ochanStatsLostCellsThe number of cells on this output channel that were dropped at the output netmod.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.4.4.1.4 |
ochanStatsTransmittedCellsThe number of cells on this output channel that were transmitted.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.4.4.1.5 |
ochanStatsIntentionalLostCellsThe number of cells on this output channel that were dropped intentionally.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.4.4.1.6 |
ochanStatsCLP0CellsThe number of CLP = 0 cells transmitted on this output path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.4.4.1.7 |
ochanStatsLostPacketsThe number of packets on this output path that were dropped at the output netmod.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.4.4.1.8 |
ochanStatsTransmittedPacketsThe number of Packets on this output path that were transmitted.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.4.4.1.9 |
topologyGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.5 |
numberOfLinksCurrent number of links known by this ATM switch.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.5.1 |
linkTableA table of links describing this switch's view of the ATM network topology. SEQUENCE OF LinkEntry .1.3.6.1.4.1.326.2.2.2.1.5.2 |
linkEntryA table entry containing link information. LinkEntry .1.3.6.1.4.1.326.2.2.2.1.5.2.1 |
linkSrcThe ATM address of the source switch of this link.ro SpansAddress .1.3.6.1.4.1.326.2.2.2.1.5.2.1.1 |
linkDestThe ATM address of the destination switch of this link.ro SpansAddress .1.3.6.1.4.1.326.2.2.2.1.5.2.1.2 |
linkCapacityThe free capacity of this link in kilobits per second.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.5.2.1.3 |
linkAgeThe freshness of this link information. The actual value has no units associated with it. It should be used for comparison.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.5.2.1.4 |
signalingGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.6 |
spansGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.6.1 |
sigPathTableA table of general information about the signaling path. SEQUENCE OF SigPathEntry .1.3.6.1.4.1.326.2.2.2.1.6.1.1 |
sigPathEntryA table entry containing signaling path information, indexed by port and path. SigPathEntry .1.3.6.1.4.1.326.2.2.2.1.6.1.1.1 |
sigPathPortThe value of this object identifies the port of this signalling path, and is the same as the portNumber.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.1 |
sigPathVPIThe VPI (Virtual Path Identifier) of this signaling path.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.2 |
sigPathVCIThe VCI (Virtual Channel Identifier) of the signaling channel within the signaling path.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.3 |
sigPathClsVCIThe VCI (Virtual Channel Identifier) of the connectionless channel within the signaling path.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.4 |
sigPathAdminStatusThe desired state of this signaling channel. The up(1) state dictates that SPANS (Simple Protocol for ATM Network Siganlling) messages are used for signalling. The down(2) state dictates the SPANS protocol is not used for signalling.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.5 |
sigPathOperStatusThe current operational state of this signaling channel, as determined either by administrative action, when the value of sigPathAdminStatus is down(2), or by a link monitoring protocol, when the value of sigPathAdminStatus is up(1).ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.6 |
sigPathEntryStatusThe status of this signaling path entry.rw EntryStatus .1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.7 |
sigPathAALTypeThe AAL (ATM Adaptation LAyer) type that is used by this signaling path.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.8 |
sigPathCDVThe signalling path Cell Delay Variation (CDV) specified in microseconds, indicates the time window in which a cell may be received on a signalling channel and be accepted. A cell that is received on a channel outside the CDV window will be dropped. The sigPathCDV value overrides the default value of switchCDV.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.9 |
sigPathPolicingActionThis object indicates the action the switch will take in case of bandwidth violation on a signalling channel. The value set here overrides the default value of switchPolicingAction.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.10 |
sigPathRemoteAtmAddressThe ATM address of the entity connected to this signalling path.ro SpansAddress .1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.11 |
sigPathRemoteIpAddressThe IP address of the entity connected to this signalling path.ro IpAddress .1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.12 |
sigPathTypeThe type of the signalling path connection. uni(1) (User Network Interface) means that there is a host on remote side, while nni(2) (Network Network Interface) means there is another switch, that speaks SPANS, on the remote side.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.13 |
sigPathClsUpcContractThe UPC contract that will be used to police the connectionless VC. This is the number of a row in the upcContractTablerw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.14 |
sigPathSigReservedBWBandwidth reserved for the SPANS Signaling VC, in cells/sec.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.15 |
sigPathMinVCIThe minimum configured VCI (Virtual Channel Identifier) that can be used for SVCs (Signalled Virtual Circuits).rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.16 |
sigPathMaxVCIThe maximum configured VCI (Virtual Channel Identifier) that can be used for SVCs (Signalled Virtual Circuits).rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.17 |
sigPathOpenTimeoutThe timeout in msec for SPANS open requests.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.18 |
sigPathCloseTimeoutThe timeout in msec for SPANS close requests.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.19 |
sigPathOutputSigServiceService Queue where the output signalling vc should be inserted into.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.20 |
sigPathAALOperTypeThe AAL (ATM Adaptation LAyer) type that is currently being used by this signaling path.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.1.1.1.21 |
sigPathStatsTableA table of statistics about the signaling path. SEQUENCE OF SigPathStatsEntry .1.3.6.1.4.1.326.2.2.2.1.6.1.2 |
sigPathStatsEntryA table entry containing signaling path statistics, indexed by port and path. SigPathStatsEntry .1.3.6.1.4.1.326.2.2.2.1.6.1.2.1 |
sigPathStatsPortThe value of this object identifies the port of this signalling path, and is the same as sigPathPort.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.1.2.1.1 |
sigPathStatsVPIThe value of this object identifies the VPI (Virtual Path Identifier) of this signaling path statistics entry, and is the same as sigPathVPI.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.1.2.1.2 |
sigPathVCCsThe number of Virtual Channel Connections (VCCs) on this signaling path.ro Gauge32 .1.3.6.1.4.1.326.2.2.2.1.6.1.2.1.3 |
sigPathRestartsThe number of times the switch has lost and regained contact with the remote signaling entity on this path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.6.1.2.1.4 |
sigPathCallsCompletionsThe number of successfully completed calls on this signaling path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.6.1.2.1.5 |
sigPathCallsFailuresThe number of call failures on this signaling path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.6.1.2.1.6 |
sigPathCallsRejectionsThe number of connections on this signaling path that were rejected by the far end.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.6.1.2.1.7 |
sigPathSpansTransmittedMessagesThe total number of SPANS messages that have been transmitted over this signalling path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.6.1.2.1.8 |
sigPathSpansReceivedMessagesThe total number of SPANS messages that have been received on this signalling path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.6.1.2.1.9 |
sigPathClsTransmittedMessagesThe total number of connectionless messages that have been transmitted over this signalling path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.6.1.2.1.10 |
sigPathClsReceivedMessagesThe total number of connectionless messages that have been received on this signalling path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.6.1.2.1.11 |
spvcSrcNumberOfSPVCsThe number of SPVCs (Smart Permanent Virtual Circuits) that are going out of this switch (i.e. this switch is their source).ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.1.3 |
spvcSrcTableThis table contains information about SPVCs (Smart Permanent Virtual Circuits) that their source is this switch. SEQUENCE OF SpvcSrcEntry .1.3.6.1.4.1.326.2.2.2.1.6.1.4 |
spvcSrcEntryA table entry containing source SPVC (Smart Permanent Virtual Circuits) information. SpvcSrcEntry .1.3.6.1.4.1.326.2.2.2.1.6.1.4.1 |
spvcSrcSpvcIdThe value of this object uniquely identify the SPVC (Smart Permanent Virtual Circuits) that this switch is its source.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.1.4.1.1 |
spvcSrcSwitchAddrThe ATM address of the source switch.ro SpansAddress .1.3.6.1.4.1.326.2.2.2.1.6.1.4.1.2 |
spvcSrcDestSpvcIdThe SPVC (Smart Permanent Virtual Circuits) identifier at the destination switch. This object should match the spvcDestSpvcId at the destination switch.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.1.4.1.3 |
spvcSrcDestSwitchAddrThe ATM address of the destination switch.rw SpansAddress .1.3.6.1.4.1.326.2.2.2.1.6.1.4.1.4 |
spvcSrcInPortThe value of this object identifies the input port of this SPVC (Smart Permanent Virtual Circuits), and is the same as the chanrInputPort, chanPort, pathPort, and portNumber.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.1.4.1.5 |
spvcSrcInVPIThe value of this object identifies the input VPI (Virtual Path Identifier) of this SPVC (Smart Permanent Virtual Circuits), and is the same as the chanrInputVPI, chanVPI, pathVPI.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.1.4.1.6 |
spvcSrcInVCIThe value of this object identifies the input VCI (Virtual Channel Identifier) of this SPVC (Smart Permanent Virtual Circuits), and is the same as the chanrInputVCI.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.1.4.1.7 |
spvcSrcAllocBandwidthThe allocated bandwidth of this SPVC (Smart Permanent Virtual Circuits).rw Gauge32 .1.3.6.1.4.1.326.2.2.2.1.6.1.4.1.8 |
spvcSrcUpTimeThe time since this SPVC (Smart Permanent Virtual Circuits) was created in hundredths of a second.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.326.2.2.2.1.6.1.4.1.9 |
spvcSrcStatusThe status of this SPVC (Smart Permanent Virtual Circuits).ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.1.4.1.10 |
spvcSrcEntryStatusThe status of this SPVC (Smart Permanent Virtual Circuits) entry.rw EntryStatus .1.3.6.1.4.1.326.2.2.2.1.6.1.4.1.11 |
spvcDestNumberOfSPVCsThe number of SPVCs (Smart Permanent Virtual Circuits) that are coming into this switch (i.e. this switch is their destination).ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.1.5 |
spvcDestTableThis table contains information about SPVCs (Smart Permanent Virtual Circuits) that their destination is this switch. SEQUENCE OF SpvcDestEntry .1.3.6.1.4.1.326.2.2.2.1.6.1.6 |
spvcDestEntryA table entry containing destination SPVC (Smart Permanent Virtual Circuits) information. SpvcDestEntry .1.3.6.1.4.1.326.2.2.2.1.6.1.6.1 |
spvcDestSpvcIdThe value of this object uniquely identify the SPVC (Smart Permanent Virtual Circuits) that this switch is its destination. The range of this object is [1..spvcDestNumberOfSPVCs].ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.1.6.1.1 |
spvcDestSwitchAddrThe ATM address of this (the destination) switch.ro SpansAddress .1.3.6.1.4.1.326.2.2.2.1.6.1.6.1.2 |
spvcDestSrcSpvcIdThe SPVC (Smart Permanent Virtual Circuits) identifier at the source switch. This object should match the spvcSrcSpvcId at the source switch.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.1.6.1.3 |
spvcDestSrcSwitchAddrThe ATM address of the source switch.rw SpansAddress .1.3.6.1.4.1.326.2.2.2.1.6.1.6.1.4 |
spvcDestOutPortThe value of this object identifies the output port of this SPVC (Smart Permanent Virtual Circuits) and is the same as the chanrOutputPort, opathPort, and portNumber.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.1.6.1.5 |
spvcDestOutVPIThe value of this object identifies the output VPI (Virtual Path Identifier) of this SPVC (Smart Permanent Virtual Circuits), and is the same as the chanrOutputVPI, and opathVPI.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.1.6.1.6 |
spvcDestOutVCIThe value of this object identifies the output VCI (Virtual Channel Identifier) of this SPVC (Smart Permanent Virtual Circuits), and is the same as the chanrOutputVCI.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.1.6.1.7 |
spvcDestAllocBandwidthThe allocated bandwidth of this SPVC (Smart Permanent Virtual Circuits).rw Gauge32 .1.3.6.1.4.1.326.2.2.2.1.6.1.6.1.8 |
spvcDestUpTimeThe time since this SPVC (Smart Permanent Virtual Circuits) was created in hundredths of a second.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.326.2.2.2.1.6.1.6.1.9 |
spvcDestStatusThe status of this SPVC (Smart Permanent Virtual Circuits).ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.1.6.1.10 |
spvcDestEntryStatusThe status of this SPVC (Smart Permanent Virtual Circuits) entry.rw EntryStatus .1.3.6.1.4.1.326.2.2.2.1.6.1.6.1.11 |
q2931Group OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.6.2 |
q2931LayerGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.6.2.1 |
q2931AdminTableA table of general information about the Q2931 signaling path. SEQUENCE OF Q2931AdminEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1 |
q2931AdminEntryA table entry containing Q2931Admin signaling administration information, indexed by port and path. Q2931AdminEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1 |
q2931AdminPortThe value of this object identifies the port of this signalling path, and is the same as the portNumber.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.1 |
q2931AdminVPIThe VPI (Virtual Path Identifier) of this signaling path.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.2 |
q2931AdminVCIThe VCI (Virtual Channel Identifier) of the signaling channel within the signaling path.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.3 |
q2931AdminStatusThe desired state of this signaling channel. The up(1) state dictates that Q2931 messages are used for signalling. The down(2) state dictates that Q2931 protocol is not used for signalling.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.4 |
q2931OperStatusThe current operational state of this signaling channel, as determined either by administrative action, when the value of q2931AdminStatus is down(2), or by a link monitoring protocol, when the value of q2931AdminStatus is up(1).ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.5 |
q2931SSCOPOperStatusThe current operational state of the underlying SSCOP (Service Specific Connection Orientedd Protocol) on this channel. SSCOP's function is to provide a reliable data link layer for the exchange of Q.2931 signalling messages. The value up(1) reflects the value dataTransReady(4) for the SSCOPOperStatus object in the SSCOP Administration table (sscopAdminTable). All other values of that object are reflected as the value down(2) for this object.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.6 |
q2931ILMIAdminStatusThe desired state of the underlying ILMI (Interim Local Manageemnt Interface) status and configuration channel. The up(1) state dictates that ILMI messages are used for status and configuration information. The down(2) state dictates that ILMI protocol is not used.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.7 |
q2931ILMIOperStatusThe current operational state of the underlying ILMI (Interim Local Manageemnt Interface) status and configuration channel, as determined either by administrative action, when the value of q2931ILMIAdminStatus is down(2), or by a link monitoring protocol, when the value of q2931ILMIAdminStatus is up(1).ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.8 |
q2931AdminAALTypeThe AAL (ATM Adaptation Layer) type that is used by this Q2931 signaling path.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.9 |
q2931AdminUNISideThis object detemines the role this port takes in the UNI (User Network Interface). If this port is connected to a host via the private UNI, this port is on the network(2) side of the UNI, whilst if this port is connected to the Public UNI the port may be required to be the user(1) side of the connection.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.10 |
q2931AdminConfigTypeThe configuration of the UNI (User Network Interface) at initialization. Configuring the UNI to publicUNI(1) means that this link will be used between the switch and a public switch. Configuring the UNI to automode(2) means that the operational type will be determined dynamically. Configuring the UNI to iisp(3) (Interim Inter-Switch Signalling Protocol) indicates that this link is used for static routing NNI (Network to Network Interface). Configuring the type to privateNNI allows the interface to come up as PNNI type and running the PNNI routing protocol. Configuring the type as privateUNI indicates that the interface should comeup as a user-network interface UNI.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.11 |
q2931AdminOperTypeThe operational configuration of the UNI (User Network Interface). publicUNI(1) is used between the switch and a public switch. privateUNI(2) is used between the switch and a host. IISP, iisp(3), stands for Interim Inter-Switch Signalling Protocol, is used between two switches using static routing. And spansNNI(4) is used between two switches using SPANS mapping messages for dynamic routing. If the q2931AdminConfigType is set to auto(2), the value of this object may be either privateUNI(2), or spansNNI(4).ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.12 |
q2931AdminEntryStatusThe status of this signaling path entry. Setting this object to invalid(4) causes the q2931 path to be destroyed.rw EntryStatus .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.13 |
q2931AdminRemoteIpAddressThe IP address of the entity connected to this q2931 signalling path. The remote IP address is derived using ILMI on this interface.ro IpAddress .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.14 |
q2931SigReservedBWBandwidth reserved for the UNI Signaling VC, in cells/sec.rwdeprecated Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.15 |
q2931ILMIReservedBWBandwidth reserved for the UNI ILMI VC, in cells/sec.rwdeprecated Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.16 |
q2931ILMIAdminVCIThe VCI (Virtual Channel Identifier) of the ILMI signalling channel.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.17 |
q2931AdminMinVCIThe minimum configured VCI (Virtual Channel Identifier) used for SVCs (Signalling Virtual Circuits).rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.18 |
q2931AdminMaxVCIThe maximum configured VCI (Virtual Channel Identifier) used for SVCs (Signalling Virtual Circuits).rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.19 |
q2931MinVCIThe minimum actual VCI (Virtual Channel Identifier) used for SVCs (Signalling Virtual Circuits).ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.20 |
q2931MaxVCIThe maximum actual VCI (Virtual Channel Identifier) used for SVCs (Signalling Virtual Circuits).ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.21 |
q2931UNIConfigVersionThe configuration version of the UNI protocol to use at initialization. Configuring the UNI to auto(1), means that the UNI will attempt to automatically determine which version of the UNI protocol to use by reading the value of ILMI variable atmfAtmLayerUniVersion. Configuring the UNI to uni30(2) means that this link will use version 30 of the UNI protocol, likewise for uni31(3). If the nni interface has to be brought up as pnni then pnni10 version isspecified. To bring the interface as uni40 version then sepcify uni40.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.22 |
q2931UNIOperVersionThe version of the UNI that is currently being used on this link, i.e. the operational version of the UNI.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.23 |
q2931ILMIRegistrationWhether to do ILMI Address and Prefix Registration across this UNI. If disabled, no prefix registration messages are sent by the network-side, and no address registration messages are generated by the user-side. If set to ignore, then the network-side performs as it normally would, except that addresses registered are not published into the routing database. This setting is not recommended except in Public Network situations where CPE equipment requires ILMI Address registration in order to function correctly. The default value of this variable is different depending on the type of UNI being created. If creating a public UNI, this variable defaults to disable, while it defaults to enable for all other types.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.24 |
q2931CallingPDefaultAddressThe calling party address to be inserted in Connection Setup messages which do not contain Calling Party Addresses.rw NsapAddr .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.25 |
q2931AdminUseNativeE164Whether to use Native Form of E164 Addresses across this link. Used by Public UNI.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.26 |
q2931AdminNativeE164AddressNative E164 Address for this uni.rw E164Address .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.27 |
q2931AdminE164AddressResolutionWhether to resolve Private NSAPs into Native E164 addresses (using the Q2931E164AddrResTable). If disabled, but if q2931AdminUseNativeE164 is enabled, then the only address conversion performed at this UNI will be of Private NSAPs in E.164 format.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.28 |
q2931AdminFtPnniOrigCostThe cost of each pnni orig loglink. It is configured at originating end of sigpathrwdeprecated INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.29 |
q2931AdminFtPnniTermCostThe cost of each pnni term loglink. The originating side of a link informs the terminating side of the configured q2931AdminFtPnniOrigCost in a hello message. The terminating side then uses the cost value in the hello message as the q2931AdminFtPnniTermCost for topology advertisement.rodeprecated Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.30 |
q2931AdminAVPresentationThe set of Address Validation interface options as follows: (The bits in this integer have the following meanings:) Bit Significance Default ======== ============= ======== 0x0001 Address Validation Enabled disabled 0x0002 insertCallingPDefaultAddress disabled 0x0004 CallingP_delivery enabled 0x0008 CallingPSubAddr_trxf enabled 0x0010 CalledPSubAddr_trxf enabled 0x0020 BHLI_TRXF enabled 0x0040 BLLI_TRXF enabled 0x0080 BLLI_selection_TRXF enabled 0x0100 AAL_INFO_TRXF enabled --- Not used presently. ----rwdeprecated Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.31 |
q2931AdminSigModeThe configured mode for signalling: VP-associated, Non-Associated or auto mode. vpAssoc(1) stands for VP-associated signalling, if set to this value, the uni encodes the connection identifier with the VP-associated signalling bits. nonAssoc(2) is for Non-associated signalling, if set to this value the connection identifier is encoded with non-associated signalling bits. auto(3) stands for auto-configured signalling mode, if set to this value, the operating mode will be determined dynamically and will either be VP-associated or Non-associated depending on the operating type of the signalling linkrw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.32 |
q2931AdminSigAllocThe current configured allocation policy for a network side uni. If set to allocVP(1), the signalling entity will allocate connections within the containing VP only. If set to allocLink(2), the signalling entity will allocate connections in its containing VP and may allocate connections in other VPS that are available to it. If set to allocVpBundle, the uni will allocate connections in its containing VP and a bundle of other VPs which are pre-created. If set to auto(3), the operating allocation policy will be determined based on the operating type of the signalling entity and the VPI value of the VP in which the signalling channel is present. Based on these, it might be allocLink or allocVP or allocVpBundlerw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.33 |
q2931PeerPortThe value of this object identifies the port of the peer's signalling path. The value starts at zero.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.34 |
q2931InputSigContractTraffic Contract to be applied to the input signalling channel.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.35 |
q2931OutputSigServiceService Queue where the output signalling vc should be inserted into.rwdeprecated Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.36 |
q2931SSCOPNoRespTimerThe Value to be set for the duration of the SSCOP No response timer. This is the time in seconds that we will wait before bringing the SSCOP link down. If no value is specified by the user, a default value of 10 seconds is used if the oper version is uni30 and a default value of 7 secs is used if the oper version is uni31.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.37 |
q2931AdminIncomingNSAPFilterIndexThe Filter Index of the NSAP Address Filter used to filter incoming calls. If this variable is set to zero, all incoming calls on this UNI will be accepted.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.46 |
q2931AdminOutgoingNSAPFilterIndexThe Filter Index of the NSAP Address Filter used to filter outgoing calls. If this variable is set to zero, all incoming calls on this UNI will be accepted.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.47 |
q2931AdminIEFilterThe set of Information Element Filtering interface options as follows: (The bits in this integer have the following meanings:) Bit Significance Default ======== ============= ======== 0x0001 IE Filtering enabled disabled 0x0002 InsertCallingPDefaultAddress disabled 0x0004 CallingP_delivery enabled 0x0008 CallingPSubAddr_trxf enabled 0x0010 CalledPSubAddr_trxf enabled 0x0020 BHLI_trxf enabled 0x0040 BLLI_trxf enabled 0x0080 BLLI_selection_trxf enabled 0x0100 AAL_Info_trxf enabled --- not used presently ---- The valid combinations of bits 0x40 (BLLI_TRXF) and 0x80 (BLLI_selection_TRXF) are: 0xc0 (1 1) transfer all BLLIs default 0x80 (1 0) **invalid** 0x40 (0 1) transfer only the first BLLI 0x00 (0 0) remove all BLLIsrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.48 |
q2931SendCallProcA flag which allows the user to specify at creation time if CALL PROCEEDING should be sent on this particular interface. If set to on(1), a CALL PROCEEDING message is sent out that interface for every SETUP received on that interface that is successfully forwarded. If set to off(2), no CALL PROCEEDING messages are sent on this interface.rwdeprecated Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.49 |
q2931VCIRangeStatusA flag which indicates the status of Min/MaxVCI range with respect to whether or not the range values are assigned after negotiating with the peer through ILMI process. This variable is set to valid if ILMI is up and range negotiation with the peer is completed, except if a UNI (link) is configured as IISP or ILMI-down, then the value of this MIB value is always set to valid.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.51 |
q2931ClearOnCarrierLossThis object indicates whether to clear calls when carrier is lost on the link associated with this signalling channel. The default value is noClear(1). This follows the ATM Forum specification which requires the specific signalling timers to expire before clearing the connections. Setting this value to clearCalls(2) will result in the connections being torn down as soon as carrier loss is detected (not compliant with ATM Forum signalling specifications).rwobsolete Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.52 |
q2931QosClassExpansionKeyThe key for the QOS Class Expansion Table to be used for this UNI.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.54 |
q2931AtmrConfDomainIDThis is the ID of the routing domain to which this interface belongs if this uni is operating as a private UNI, public UNI or IISPrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.55 |
q2931AtmrPnniNodeIndexThis is the index of the node to which this interface attaches for FT-PNNI and PNNI interfaces. The value is always 0xffff for FT-PNNI interfaces.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.56 |
q2931AdminOperSigModeThe operating mode for signalling: VP-associated or Non-associated. vpAssoc(1) stands for VP-associated signalling, if set to this value, the uni encodes the conn_id with the VP-associated signalling bits. nonAssoc(2) stands for Non-associated signalling, if set to this value, the uni encodes the conn_id with Non-associated signalling bits.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.57 |
q2931AdminOperSigAllocThe operating allocation policy for a network side uni. If set to allocVP, the network side uni will allocate connections in its containing VP only. If set to allocLink, the uni will allocate connections in its containing VP and may allocate connections in other VPS that are available to it. If set to allocVpBundle, the uni will allocate connections in its containing VP and a bundle of other VPs which are pre-created.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.58 |
q2931OutputSigUpcTraffic contract to be applied to the output side of the signalling channel. If this is not specified, signalling will be put in the vbr queue with no bandwidth reservation and no policing.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.60 |
q2931AdminPlanTypeThis is the plan type to be used in calling party number and called party number IEs in the signalling messages. The value of this variable is dependent on whether q2931AdminUseNativeE164 is set to enable or disable. Further, q2931AdminPlanType can be set in conjunction with q2931AdminUseNativeE164. When q2931AdminUseNativeE164 is set to disable, q2931AdminPlanType takes a default value of 1(unknown). All other values are invalid. When q2931AdminUseNativeE164 is set to enable, q2931AdminPlanType takes a default value of 2(international). Other valid values are 3(national) and 4(subscriber).rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.61 |
q2931AdminMaxVPIThe maximum configured VPI (Virtual Path Identifier) that is used for SVPs (Signalling Virtual Paths) when this interface sets up SVP Connections and also the Max VPI that is used to create dynamic paths for SVCs (Signalling Virtual Circuit) connections.rw INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.62 |
q2931MaxSvccVPIThe maximum actual VPI (Virtual Path Identifier) that will be used for SVCs (Signalling Virtual Circuit) dynamic paths. This variable denotes the operating value for the maximum VPI value that can be used for setting up dynamic path SVPS. The operating value can differ from the configured value (q2931AdminMaxVPI) as the operating value depends on the outcome of possible ILMI based VPI range negotiation procedure.ro INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.63 |
q2931LastChangeTimeThe time the Signalling entity was created in hundredths of a second.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.64 |
q2931NNIProtoThe NNI protocol being run on this linkro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.66 |
q2931MaxSvpcVPIThe maximum actual VPI (Virtual Path Identifier) that will be used for SVPs (Signalling Virtual Paths). This variable denotes the operating value for the maximum VPI value that can be used for setting up dynamic path SVPS. The operating value can differ from the configured value (q2931AdminMaxVPI) as the operating value depends on the outcome of possible ILMI based VPI range negotiation procedure.ro INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.67 |
q2931VpCapabilityThis mib variable is used to determine if this interface is capable of supporting Switched VPs. For UNI3.x and VP Scope Signalling Interfaces, SVPs (Switch Virtual Paths) cannot be created and hence undefined(1). For UNI40 & PNNI Link Scope interfaces, if there is a non-zero VPI range intersection with the peer, the interface is vpCapable(2), else notVpCapable(3)ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.68 |
q2931VpciGroupIndexThe index into the VPCI Mapping Group Table to use for this signalling interface.rw INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.69 |
q2931AcceleratedClearThis object indicates whether to clear calls when carrier is lost on the link associated with this signalling channel or the Virtual Path goes down. The default value is noClear(1). This follows the ATM Forum specification which requires the specific signalling timers to expire before clearing the connections. Setting this value to clearCalls(2) will result in the connections being torn down as soon as carrier loss/VP failure is detected (not compliant with ATM Forum signalling specifications).rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.70 |
q2931SupplementaryServicesStatusThis MIB variable is used to enable or disable all the supplementary services features for this interface. This acts as a global switch for this interface to disable or enable all of the supplementary services. The MIB variables defined for all supplementary services will be used only when this is enabled. The supplementary services is disabled by default. The value of undefined(3) is a read-only value used for interfaces where supplementary services are not applicable.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.71 |
q2931CallingPAddressPresentationThe Calling party address presentation can be set to one of the two values as described above. The CLIP MIB variable is used when this interface is acting as a called party for a call setup message. When set to enable(1), while a call setup message is forwarded through this interface, the calling party number is provided. When set to disable(2), the calling party number is not provided in the call setup message. The value of undefined(3) is a read-only value used for interfaces where supplementary services are not applicable.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.72 |
q2931CallingPAddressRestrictionThe Calling party address restriction can be set to one of the two values as described above. The CLIR MIB variable is used when this interface is acting as a calling party for a call setup message. When set to enable(1), while a call setup mes-sage is received from this interface and forwarded out, the calling party number is not provided to called user. When set to disable(2), the calling party number is provided to the called user. The value of undefined(3) is a read-only value used for interfaces where supplementary services are not applicable.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.73 |
q2931ConnectedPAddressPresentationThe Connected party address presentation can be set to one of the two values as described above. The COLP MIB variable is used when the interface is acting as a calling party to a call setup message. When set to enable(1), while a call establish-ment response message is forwarded through this interface, the connected party number is provided to the calling user. When set to disable(2), while a call establishment response message is forwarded through this interface, the connected party number is not provided to the calling user. The value of undefined(3) is a read-only value used for interfaces where supplementary services are not applicable.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.74 |
q2931ConnectedPAddressRestrictionThe Connected party address restriction can be set to one of the two values as described above. The COLR MIB variable is used when the interface is acting as a called party to a call setup message. When set to enable(1), while a call establishment response message is forwarded from this interface, the connected party number is not provided to the calling user. When set to disable(2),while a call establishment response message is forwarded from this interface, the connected party number is provided to the calling user. The value of undefined(3) is a read-only value used for interfaces where supplementary services are not applicable.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.75 |
q2931ConnectedPDefaultAddressThe connected party address to be used in Connection Acceptance (connect, add party ack etc.) messages that do not contain Connected Party Addresses.rw NsapAddr .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.76 |
q2931SubaddressingAdminStatusThis is used to enable or disable the sub-addressing capability. If this is set to enable(1), the called party sub-address IE is passed along. Ifthis is set to disbale(2), this IE is removed while forwarding the messages. The value of undefined(3) is a read-only value used for interfaces where supplementary services are not applicable.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.77 |
q2931UserUserSignallingAdminStatusThis is used to enable or disable the User to User Signalling capability. If this is set to enable(1), the UUS IE is passed along. If this is set to disbale(2), this IE is removed while forwarding the messages. The value of undefined(3) is a read-only value used for interfaces where supplementary services are not applicable.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.78 |
q2931OutputIlmiUpcThe index into the UPC table for the ILMI channelrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.79 |
q2931OutputRccUpcThe index into the UPC table for the RCC channelrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.80 |
q2931PnniRccVciThis is used to specify the PVC RCC VCI used by PNNI. Normally this will always be 18, but if a user creates a VPT with a VCI range that does not contain 18, then this field is used to specify the PNNI PVC RCC VCI.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.81 |
q2931AdminubrCallsThis flag is used to disable processing of UBR calls.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.82 |
q2931AdmincbrCallsThis flag is used to disable processing of CBR calls.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.83 |
q2931AdminabrCallsThis flag is used to disable processing of ABR calls.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.84 |
q2931AdminrtvbrCallsThis flag is used to disable processing of RT-VBR calls.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.85 |
q2931AdminnrtvbrCallsThis flag is used to disable processing of NRT-VBR calls.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.86 |
q2931ProxyDirGroupIndexThe index into the proxy address group table to use for this signalling interface.rw INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.1.1.1.87 |
q2931StatsTableA table of statistics about the Q2931 signaling path. SEQUENCE OF Q2931StatsEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.1.2 |
q2931StatsEntryA table entry containing signaling path statistics, indexed by port and path. Q2931StatsEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.1.2.1 |
q2931StatsPortThe value of this object identifies the port of this signalling path, and is the same as q2931Port.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.2.1.1 |
q2931StatsVPIThe value of this object identifies the VPI (Virtual Path Identifier) of this signaling path statistics entry, and is the same as q2931VPI.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.2.1.2 |
q2931VCCsThe number of Virtual Channel Connections (VCCs) on this signaling path.ro Gauge32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.2.1.3 |
q2931RestartsThe number of times the switch has lost and regained contact with the remote signaling entity on this path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.2.1.4 |
q2931CallsCompletionsThe number of successfully completed calls on this signaling path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.2.1.5 |
q2931CallsFailuresThe number of call failures on this signaling path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.2.1.6 |
q2931CallsRejectionsThe number of connections on this signaling path that were rejected by the far end.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.2.1.7 |
q2931TransmittedMessagesThe total number of Q2931 messages that have been transmitted over this signalling path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.2.1.8 |
q2931ReceivedMessagesThe total number of Q2931 messages that have been received on this signalling path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.2.1.9 |
q2931AddressFilterGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6 |
q2931AFTemplateTableA table of allowable (or rejectable) NSAP source and destination addresses. SEQUENCE OF Q2931AFTemplateEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1 |
q2931AFTemplateEntryA table entry containing NSAP address filtering information. Q2931AFTemplateEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.1 |
q2931AFTemplateIndexThe value of this object identifies the NSAP Address Filter Template to which this entry belongs. Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.1.1 |
q2931AFTemplateSrcPortThe source UNI port matched by this entry. A value of -1 matches all ports.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.1.2 |
q2931AFTemplateSrcVPIThe source UNI VPI matched by this entry. A value of -1 matches all VPIs.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.1.3 |
q2931AFTemplateSrcNsapThe Source NSAP address filtered by this table entry.rw NsapAddr .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.1.4 |
q2931AFTemplateSrcNsapMaskThe mask applied to the source address in order to compare against the above q2931AFTemplateEntrySrcNsap. A mask of 0 bits matches all source addresses.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.1.5 |
q2931AFTemplateDstPortThe destination UNI port matched by this entry. A value of -1 matches all ports.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.1.6 |
q2931AFTemplateDstVPIThe destination UNI VPI matched by this entry. A value of -1 matches all VPIs.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.1.7 |
q2931AFTemplateDstNsapThe Destination NSAP address filtered by this table entry.rw NsapAddr .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.1.8 |
q2931AFTemplateDstNsapMaskThe mask applied to the destination address in order to compare against the above q2931AFTemplateDstNsap. A mask of 0 bits matches all destination addresses.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.1.9 |
q2931AFTemplateActionWhat to do with addresses that match this entry.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.1.10 |
q2931AFTemplateNameAn optional text name for the template.rw OCTET STRING .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.1.11 |
q2931AFTemplateStatusThe status of this table entry. This entry may not be destroyed if there are any filter entries that refer to it.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.1.12 |
q2931AFTemplateNextIndexThe index of the next free row in the q2931AFTemplateTable.rw TestAndIncr (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.1.2 |
q2931AFFilterTableA table of filters, each composed of an ordered list of address filtering templates. SEQUENCE OF Q2931AFFilterEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.2 |
q2931AFFilterEntryA table entry for one filter. Q2931AFFilterEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.2.1 |
q2931AFFilterIndexThe value of this object identifies the NSAP Address Filter to which this entry belongs. Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.2.1.1 |
q2931AFFilterNameAn optional text name for the filter.rw OCTET STRING .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.2.1.2 |
q2931AFFilterStatusThe status of this table entry. Setting this variable to destroy removes this row from the q2931AFFilterTable, and removes the corresponding entries from the q2931AFFilterTListTable.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.2.1.3 |
q2931AFFilterNextIndexThe index of the next free row in the q2931AFFilterTable.rw TestAndIncr (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.2.2 |
q2931AFFilterTListTableA table of template lists for filters. A template list is composed of an ordered list of address filtering templates. All objects with the same value for q2931AFFilterIndex are conceptually part of the corresponding q2931AFFilterEntry. SEQUENCE OF Q2931AFFilterTListEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.3 |
q2931AFFilterTListEntryA table entry holding one template in a filter's template list. Q2931AFFilterTListEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.3.1 |
q2931AFFilterTListIndexThe value of this object identifies the order in this NSAP Address Filter in which this template is applied. Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.3.1.1 |
q2931AFFilterTListTemplateIndexThe value of this object identifies the NSAP Address Filter Template for this entry.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.3.1.2 |
q2931AFFilterTListStatusThe status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.3.1.3 |
q2931AFStatsTableA table of address filtering statistics. SEQUENCE OF Q2931AFStatsEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.4 |
q2931AFStatsEntryAn entry in the table of address filtering statistics. There are two entries for each UNI: one for incoming call setup attempts, and one for outgoing call setup attempts. Q2931AFStatsEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.4.1 |
q2931AFDirectionThe value of this object identifies whether this row of the statistics table applies to incoming or outgoing call attempts. Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.4.1.1 |
q2931AFAcceptsThe total number of Q2931 messages that have been accepted by Address Filtering on this UNI.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.4.1.2 |
q2931AFRejectKnownsThe total number of Q2931 messages that have been rejected because the supplied address matched a template in the address filtering table where the action was to reject the call.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.4.1.3 |
q2931AFRejectUnknownsThe total number of Q2931 messages that have been rejected because the supplied address matched no template in the address filtering table.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.4.1.4 |
q2931AFLookupTableThe Lookup facility for NSAP address filtering. SEQUENCE OF Q2931AFLookupEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.5 |
q2931AFLookupEntryThe result of an inquiry to the Lookup facility. Q2931AFLookupEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.5.1 |
q2931AFLookupIndexThe value of this object identifies this entry in the Filter Lookup table. Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.5.1.1 |
q2931AFLookupNSAPFilterIndexThe index of the NSAP address filter for this lookup.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.5.1.2 |
q2931AFLookupSrcPortThe simulated incoming Port for this filter lookup.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.5.1.3 |
q2931AFLookupSrcVPIThe simulated incoming VPI for this filter lookup.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.5.1.4 |
q2931AFLookupSrcNsapThe Source NSAP address for this filter lookup.rw NsapAddr .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.5.1.5 |
q2931AFLookupDstPortThe simulated outgoing Port for this filter lookup.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.5.1.6 |
q2931AFLookupDstVPIThe simulated outgoing VPI for this filter lookup.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.5.1.7 |
q2931AFLookupDstNsapThe Destination NSAP address for this filter lookup.rw NsapAddr .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.5.1.8 |
q2931AFLookupResultThe result of a filter Lookup on the selected values: 1 Accepted 2 Rejectedro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.5.1.9 |
q2931AFLookupTemplateThe index of the template in the address filter that either accepted or rejected the call. It is zero if the address was unknown.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.5.1.10 |
q2931AFLookupStatusThe status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.5.1.11 |
q2931AFLastFailureGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.6 |
q2931AFLastFailureSrcPortThe incoming port for this failed call attempt.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.6.1 |
q2931AFLastFailureSrcVPIThe incoming VPI for this failed call attempt.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.6.2 |
q2931AFLastFailureSrcNsapThe source address of this failed call attempt.ro NsapAddr .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.6.3 |
q2931AFLastFailureDstPortThe outgoing port for this failed call attempt.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.6.4 |
q2931AFLastFailureDstVPIThe outgoing VPI for this failed call attempt.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.6.5 |
q2931AFLastFailureDstNsapThe destination address of this failed call attempt.ro NsapAddr .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.6.6 |
q2931AFLastFailureTemplateIndexThe index of the template which rejected this call attempt. If this call was rejected because its addresses were not known, this field is set to zero.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.6.7 |
q2931AFLastFailureDirectionThe value of this object identifies whether the incoming (source) or outgoing (destination) filter rejected the call. Its value is irrelevant for accepted calls.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.6.6.8 |
q2931NSAPPingGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.6.2.1.7 |
q2931NPCallTableA table of NSAP addressed and call parameters to be used in testing the reachability of destination addresses. SEQUENCE OF Q2931NPCallEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1 |
q2931NPCallEntryA table entry containing NSAP address, call parameter information. Q2931NPCallEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1 |
q2931NPCallIndexThe value of this object identifies an entry in the q2931NPCallTable. Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.1 |
q2931NPCallDstNsapThe Destination NSAP address used by this table entry.rw NsapAddr .1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.2 |
q2931NPCallStateThis field keeps the state of the nsap call. This field is set to inprogress by default. 'up' means call was successful, 'down' means call was rejected by the destination, 'err' means call was not attempted primarily because no route to destination was available, 'locpref', 'lochost' mean that the address is localrw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.3 |
q2931NPCallClientTypeHolds the type of the client expected to answer the call at destination. Set to noIndication by default.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.4 |
q2931NPCallFwdUpcKeyUPC table entry to be used in the forward direction of the call is stored here. Set to ZERO by default.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.6 |
q2931NPCallBckUpcKeyUPC table entry to be used in the backward direction of the call is stored here. Set to ZERO by default.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.7 |
q2931NPCallCallingDomainThe domain at the originating switch on which the call has to be routed. By default this is set to the default domain, control port domain.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.8 |
q2931NPCallQosIndexQOS Index entry to be used in the forward direction of the call is stored here. Set to ZERO by default.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.9 |
q2931NPCallQosClassFwdQOS Class for forward direction of the call. Set to ZERO by default.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.10 |
q2931NPCallQosClassBwdQOS Class for backward direction of the call. Set to ZERO by default.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.11 |
q2931NPCallBearerClassBearer Class to be used for the NSAP Ping call. Set to classX by default.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.12 |
q2931NPCallVerboseHolds the info, whether the call setup messages have to be displayed on user console or not. By default set to off.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.13 |
q2931NPCallStatusThe status of this table entry. This entry may not be destroyed if there are any filter entries that refer to it.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.14 |
q2931NPPingStateThis field tracks the state of the ping process. Invalid is the initial state, when the connection is made the state changes to 'inprogress' and when the ping is complete the state changes to 'complete'.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.15 |
q2931NPCallCauseCodeThe UNI call setup failure cause code. This value is valid only if the call state is 'down'ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.16 |
q2931NPPingPktCountThe number of ping packets used in the ping processrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.17 |
q2931NPPingStatsPktsSentThe number of ping packets actually sentro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.18 |
q2931NPPingStatsPktsReceivedThe number of ping packets replied to by the destinationro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.19 |
q2931NPPingStatsAverageDelayThe average round trip delay expressed in milli seconds.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.20 |
q2931NPMeasureRoundTripDelayHolds the info, whether the ping process has to be done after the connection is made, By default set to offrw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.21 |
q2931NPPingStatsMaximumDelayThe maximum round trip delay expressed in milli seconds.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.22 |
q2931NPPingStatsMinimumDelayThe minimum round trip delay expressed in milli seconds.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.1.1.23 |
q2931NPCallNextIndexThe index of the next free row in the q2931NPCallTable.rw TestAndIncr (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.1.7.2 |
perCallDbgFilterGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.6.2.1.8 |
perCallDbgFilterTableA table of Per Call Debugging Filter entries. SEQUENCE OF PerCallDbgFilterEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.1.8.1 |
perCallDbgFilterEntryA table entry containing a Per Call Debugging filter. PerCallDbgFilterEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.1.8.1.1 |
perCallDbgFilterIndexThe value of the object indicates the index of this entry in the PCD table. A limit will be set as a constant to limit the number of filter that can exist at once. Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.8.1.1.1 |
perCallDbgFilterTemplateIdThe value of this object reflects the index of the template to be used for this filterrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.8.1.1.2 |
perCallDbgFilterNameThe value of this object reflects a name that will be printed out with the debug messages generated by this feature.rw OCTET STRING .1.3.6.1.4.1.326.2.2.2.1.6.2.1.8.1.1.3 |
perCallDbgFilterFlavorThe value of this object reflects the type of debugging that has been enabled.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.8.1.1.4 |
perCallDbgFilterMatchesThe value of this object reflects the number of SVC setup messages matches that have been found for this filter.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.6.2.1.8.1.1.5 |
perCallDbgFilterRowStatusThe status of this PCD filter entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.1.8.1.1.6 |
perCallDbgTransFlagEnables a switch to generate and print PCD debugging information when a switch receives a PCD GIT IE. The default value will be enabled.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.1.8.2 |
pnniSpvcSrcNumberOfSPVCsThe number of SPVCs (Smart Permanent Virtual Circuits) that have their source at this switch.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.2 |
pnniSpvcSrcTableThis table contains information about SPVCs (Smart Permanent Virtual Circuits) that have their source at this switch. SEQUENCE OF PnniSpvcSrcEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.3 |
pnniSpvcSrcEntryA table entry containing source SPVC (Smart Permanent Virtual Circuits) information. PnniSpvcSrcEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1 |
pnniSpvcSrcIndexThe value of this object uniquely identify the SPVCs (Smart Permanent Virtual Circuits) that have this switch as their source.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.1 |
pnniSpvcSrcCallingPortThe value of this object identifies the input port of this SPVC (Smart Permanent Virtual Circuits), and is the same as the chanrInputPort, chanPort, pathPort, and portNumber.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.2 |
pnniSpvcSrcCallingVPIThe VPI to be used at the Calling NI for this SPVC.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.3 |
pnniSpvcSrcCallingVCIThe VCI to be used at the Calling NI SPVC.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.4 |
pnniSpvcSrcCalledAtmAddrThe ATM address of the distant end NI (remote switch) for this SPVC.rw NsapAddr .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.5 |
pnniSpvcSrcCalledPortThe value of this object identifies the port of this SPVC (Smart Permanent Virtual Circuits) at the destination end. It has a value of -1 if the port at the destination switch cannot be determined.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.6 |
pnniSpvcSrcCalledVPVCSelThe Called VPI/VCI value selection qualifier.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.7 |
pnniSpvcSrcCalledVPIThe VPI to be used at the Called NI for this SPVC.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.8 |
pnniSpvcSrcCalledVCIThe VCI to be used at the Called NI for this SPVC.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.9 |
pnniSpvcSrcCalledAssignedVPIThe VPI assigned at the Called NI for this SPVC. This value is only meaningful if the SPVC status is up.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.10 |
pnniSpvcSrcCalledAssignedVCIThe VCI assigned at the Called NI for this SPVC. This value is only meaningful if the SPVC status is up.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.11 |
pnniSpvcSrcFwdUpcKeyThe forward UPC traffic contract key for this SPVC. This key must be defined in the upcContractTable.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.12 |
pnniSpvcSrcBckUpcKeyThe forward UPC traffic contract key for this SPVC. This key must be defined in the upcContractTable.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.13 |
pnniSpvcSrcBearerClassThe requested broadband bearer class for this SPVC.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.14 |
pnniSpvcSrcTrafficTypeThe requested broadband bearer traffic type for this SPVC.rwobsolete Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.15 |
pnniSpvcSrcTimingReqThe requested broadband bearer timing requirements for this SPVC.rwobsolete Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.16 |
pnniSpvcSrcSusceptClipThe requested broadband bearer susceptability to for this SPVC.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.17 |
pnniSpvcSrcFwdQoSClassThe requested quality of service for this SPVC in the forward (calling to called) direction.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.18 |
pnniSpvcSrcBckQoSClassThe requested quality of service for this SPVC in the backward (called to calling) direction.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.19 |
pnniSpvcSrcTransitNetSelThe optional transit network selection for this SPVC.ro TransitNetwork .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.20 |
pnniSpvcSrcLastFailCauseThe last call setup failure cause code for this SPVC.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.21 |
pnniSpvcSrcRetryCountThe number of times the call setup has been attempted since the SPVC creation or the last successful call setup.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.22 |
pnniSpvcSrcLastChangeTimeThe time since this SPVC (Smart Permanent Virtual Circuits) has been up/down in hundredths of a second.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.23 |
pnniSpvcSrcStatusThe operational status of this SPVC (Smart Permanent Virtual Circuit).ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.24 |
pnniSpvcSrcNameThe value of this object identifies the name that has been assigned for this SPVC.rw OCTET STRING .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.25 |
pnniSpvcSrcEntryStatusThe status of this SPVC (Smart Permanent Virtual Circuits) entry.rw EntryStatus .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.26 |
pnniSpvcSrcRouteCostThe cumulative route cost for the current route of this SPVC (Smart Permanent Virtual Circuits).ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.27 |
pnniSpvcSrcDtlIndexThe Designated Transit List (DTL) index for this SPVC (Smart Permanent Virtual Circuit). This variable has been deprecated. Any writes to this variable will be treated as writes to pnniSpvcSrcDtlIndex1. This value must be defined in the ftPnniDTLTable. The DTL specifies a preferred call routing for the SVC portion of the SPVC.rwobsolete Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.28 |
pnniSpvcSrcActiveDtlIndexThe Active Designated Transit List (DTL) index for this SPVC (Smart Permanent Virtual Circuit). This value along with pnniSpvcSrcActiveDtlNodeIndex uniquely identifies the DTL that is currently used by the SVC portion of the SPVC.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.29 |
pnniSpvcSrcRerouteStatusThe status of the reroute function for this SPVC (Smart Permanent Virtual Circuit). If set to disabled(2), no rerouting will be attempted for this SPVC.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.30 |
pnniSpvcSrcCallingDomainThe Domain ID to be used at the Calling NI SPVC.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.31 |
pnniSpvcSrcQosIndexThe index for the QOS Class Expansion Table to be used for this spvc.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.32 |
pnniSpvcSrcDtlIndex1The first Designated Transit List (DTL) index for this SPVC (Smart Permanent Virtual Circuit). This value must be defined in the ftPnniDTLTable. The DTL specifies a preferred call routing for the SVC portion of the SPVC.rwobsolete Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.33 |
pnniSpvcSrcDtlIndex2The second Designated Transit List (DTL) index for this SPVC (Smart Permanent Virtual Circuit). This value must be defined in the ftPnniDTLTable. The DTL specifies a preferred call routing for the SVC portion of the SPVC.rwobsolete Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.34 |
pnniSpvcSrcDtlIndex3The third Designated Transit List (DTL) index for this SPVC (Smart Permanent Virtual Circuit). This value must be defined in the ftPnniDTLTable. The DTL specifies a preferred call routing for the SVC portion of the SPVC.rwobsolete Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.35 |
pnniSpvcSrcDtlIndex4The fourth Designated Transit List (DTL) index for this SPVC (Smart Permanent Virtual Circuit). This value must be defined in the ftPnniDTLTable. The DTL specifies a preferred call routing for the SVC portion of the SPVC.rwobsolete Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.36 |
pnniSpvcSrcDtlWeight1The weight of the first Designated Transit List (DTL) index for this SPVC (Smart Permanent Virtual Circuit). The weight specifies the priority of this DTL index among the four DTL indices that can be specified for a particular SPVC.rwobsolete Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.37 |
pnniSpvcSrcDtlWeight2The weight of the second Designated Transit List (DTL) index for this SPVC (Smart Permanent Virtual Circuit). The weight specifies the priority of this DTL index among the four DTL indices that can be specified for a particular SPVC.rwobsolete Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.38 |
pnniSpvcSrcDtlWeight3The weight of the third Designated Transit List (DTL) index for this SPVC (Smart Permanent Virtual Circuit). The weight specifies the priority of this DTL index among the four DTL indices that can be specified for a particular SPVC.rwobsolete Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.39 |
pnniSpvcSrcDtlWeight4The weight of the fourth Designated Transit List (DTL) index for this SPVC (Smart Permanent Virtual Circuit). The weight specifies the priority of this DTL index among the four DTL indices that can be specified for a particular SPVC.rwobsolete Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.40 |
pnniSpvcSrcBackoffStatusThe status of the backoff function for this SPVC (Smart Permanent Virtual Circuit). If set to disabled(2), directed dtls configured for this SPVC will be continually retried on failure.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.41 |
pnniSpvcSrcPriorityPriority of this SPVCC for connectionrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.42 |
pnniSpvcSrcLastLocationThe last call setup failure location code for this SPVC. This indicates the switch that initiated the clearing for the call. This is formatted as a text string with the fields: FMT: Indicates diagnostic format RMT: Indicates whether a remote switch is the source of the failure or this switch inserted the location diag LINK:Link id that clear pertains to VPI: VPI that clear pertains to The remaining fields are format specificro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.43 |
pnniSpvcSrcOldRouteCostThis OID is specified only to be included the the pnniSpvcUp trap. It specifies the path cost of the call the previous time this call was up. If the call has not been up, this will report a value of -1.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.44 |
pnniSpvcSrcDownReasonThis OID is specified only to be included the the pnniSpvccDown and pnniSpvccFail traps. This specifies whether the SPVC call was cleared due to a better route being found, a network failure, or SPVC deletion.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.45 |
pnniSpvcSrcActiveDtlNodeIndexThe Node index of the Active Designated Transit List for this SPVC (Smart Permanent Virtual Circuit). The active DTL indexed by the node index and DTL index identifies the DTL that is currently used by the SVC portion of the SPVC. The value of this object is 65535 for FTPNNI nodes.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.46 |
pnniSpvcSrcDtlTagThis value specifies an index into a table of DTLs, the DTL entries in this table will be used to setup the SPVC.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.47 |
pnniSpvcSrcAutoDtlStatusThe status of the dynamic path selection function for this SPVC (Smart Permanent Virtual Circuit). If set to disabled(2), auto path selection will not be used.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.48 |
pnniSpvcSrcRGroupIndexThis specifies the entry in the Spvxc Redundancy Group table for information regarding the secondary port to be used as the redundant portrw INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.49 |
pnniSpvcSrcSecondaryVPIThe Secondary VPI to be used at the originating switch for the redundant permanent portion of this SPVC.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.50 |
pnniSpvcSrcSecondaryVCIThe Secondary VCI to be used at the originating switch for the redundant permanent portion of this SPVC.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.3.1.51 |
pnniSpvcDestNumberOfSPVCsThe number of connected SPVCs (Smart Permanent Virtual Circuits) that have their destination at this switch.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.4 |
pnniSpvcDestTableThis table contains information about SPVCs (Smart Permanent Virtual Circuits) that have their destination at this switch. SEQUENCE OF PnniSpvcDestEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.5 |
pnniSpvcDestEntryA table entry containing destination SPVC (Smart Permanent Virtual Circuits) information. PnniSpvcDestEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.5.1 |
pnniSpvcDestIndexThe value of this object uniquely identify the SPVCs (Smart Permanent Virtual Circuits) that have this switch as their source.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.1 |
pnniSpvcDestCallingAtmAddrThe ATM address of the local end NI (on this switch) for this SPVC.ro NsapAddr .1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.2 |
pnniSpvcDestCallingPortThe value of this object identifies the port of this terminating SPVC (Smart Permanent Virtual Circuits) at the source end. It has a value of -1 if the port at the destination switch cannot be determined.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.3 |
pnniSpvcDestCallingVPIThe VPI to be used at the Calling NI for this SPVC.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.4 |
pnniSpvcDestCallingVCIThe VCI to be used at the Calling NI for this SPVC.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.5 |
pnniSpvcDestCalledAtmAddrThe ATM address of the distant end NI (remote switch) for this SPVC.ro NsapAddr .1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.6 |
pnniSpvcDestCalledPortThe value of this object identifies the port of this terminating SPVC (Smart Permanent Virtual Circuits) at the destination end. It has a value os -1 if the port at the destination switch cannot be determined.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.7 |
pnniSpvcDestAssignedVPIThe VPI assigned at the Called NI for this SPVC. This value is only meaningful if the SPVC status is up.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.8 |
pnniSpvcDestAssignedVCIThe VCI assigned at the Called NI for this SPVC. This value is only meaningful if the SPVC status is up.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.9 |
pnniSpvcDestBearerClassThe broadband bearer class for this SPVC.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.10 |
pnniSpvcDestTrafficTypeThe broadband bearer traffic type for this SPVC.rodeprecated Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.11 |
pnniSpvcDestTimingReqThe broadband bearer timing requirements for this SPVC.rodeprecated Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.12 |
pnniSpvcDestSusceptClipThe broadband bearer susceptability to clipping for this SPVC.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.13 |
pnniSpvcDestUpTimeThe time since this SPVC (Smart Permanent Virtual Circuits) was created in hundredths of a second.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.14 |
pnniSpvcDestFwdQoSClassThe requested quality of service for this SPVC in the forward (calling to called) direction.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.15 |
pnniSpvcDestBckQoSClassThe requested quality of service for this SPVC in the backward (called to calling) direction.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.16 |
pnniSpvcDestTransitNetSelThe optional transit network selection for this SPVC.ro TransitNetwork .1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.17 |
pnniSpvcDestStatusThe operational status of this SPVC (Smart Permanent Virtual Circuit).ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.18 |
pnniSpvcDestRGroupIndexThis specifies the entry in the Spvxc Redundancy Group table for information regarding the secondary port to be used as the redundant port. This will used at the terminating PVC end.ro INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.5.1.19 |
q2931PublicGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.6.2.6 |
q2931E164AddrResTableA table of E164 Address Resolution entries. SEQUENCE OF Q2931E164AddrResEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.6.1 |
q2931E164AddrResEntryA table entry containing E164 Address Resolution information, indexed by Nsap. Q2931E164AddrResEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.6.1.1 |
q2931E164Portro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.6.1.1.1 |
q2931E164VPIro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.6.1.1.2 |
q2931E164Nsapro NsapAddr .1.3.6.1.4.1.326.2.2.2.1.6.2.6.1.1.3 |
q2931E164NsapMaskro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.6.1.1.4 |
q2931E164Addressrw E164Address .1.3.6.1.4.1.326.2.2.2.1.6.2.6.1.1.5 |
q2931E164AddrResStatusrw EntryStatus .1.3.6.1.4.1.326.2.2.2.1.6.2.6.1.1.6 |
pnniSpvcParamGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.6.2.7 |
pnniSpvcPaceIntervalThe time interval between successive callbacks to the SPVC controller to open to the destinations of a batch of SPVCsrw TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.7.1 |
pnniSpvcPaceNumSpvcsThe max number of SPVCs that each batch of SPVCs that the SPVC controller tries to open to per pnniSpvcPaceIntervalrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.7.2 |
pnniSpvcRerouteIntervalThe time interval between successive callbacks to the SPVC controller to reroute existing SPVC connection if a better path is available to the destinationrw TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.7.3 |
pnniSpvcRerouteNumSpvcsThe number of SPVCs that are attempted to be rerouted by the SPVC controller per pnniSpvcRerouteIntervalrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.7.4 |
pnniSpvcRerouteThresholdThe percentage improvement in the cost that the new SPVC path must have over the current SPVC path before a reroute will be performed.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.7.5 |
pnniSpvcLowestPriorityThe value of lowest priority for SPVCCsrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.7.6 |
pnniSpvcDefaultUbrBandwidthThe default bandwidth in Kilo-CPS to be used for UBR SPVCsrw INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.7.7 |
pnniSpvcTrapModeThis configuration item specifies whether the switch should send the: spvcRerouteInitiated OR pnniSpvccUp and pnniSpvccFail OR pnniSpvccDown, pnniSpvccFail, and pnniSpvccUp traps.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.7.8 |
pnniSpvcBackoffIntervalThe time interval to backoff a DTL that failed call setup. The DTL will not be used again until this interval has elapsed. The interval will not be applicable if backoff is disabled on the SPVC.rw TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.7.9 |
pnniPmpSpvcPartyPaceNumThe maximum number parties within a PMP SPVC that are activated per SpvcPacingInterval.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.7.10 |
pnniSpvpcParamGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.6.2.8 |
pnniSpvpcPaceIntervalThe time interval between successive callbacks to the SPVPC controller to open connections to the destinations of a batch of SPVPCs. This parameter along with pnniSpvpcPaceNumSpvpcs control the rate at which the SPVPCs that are down are established. Analogous SPVCC variable is pnniSpvcPaceInterval.rw TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.8.1 |
pnniSpvpcPaceNumSpvpcsThe max number of SPVPCs that the SPVPC controller tries to activate per pnniSpvpcPaceInterval. This controls the rate at which SPVPCs that are down are established. The corresponding SPVCC variable is pnniSpvcPaceNumSpvcs.rw INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.8.2 |
pnniSpvpcRerouteIntervalThe time interval between successive callbacks to the SPVPC controller to reroute existing SPVPC connections if a better path is available to the destination. This is one of the parameters that control the rate at which rerouting is attempted. The analogous SPVCC variable is pnniSpvcRerouteInterval.rw TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.8.3 |
pnniSpvpcRerouteNumSpvpcsThe number of SPVPCs that are attempted to be rerouted by the SPVPC controller per pnniSpvpcRerouteInterval. Thus it determines the rerouting rate. The analogous SPVCC variable is pnniSpvcRerouteNumSpvcs.rw INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.8.4 |
pnniSpvpcRerouteThresholdThe percentage improvement in the cost that the new SPVPC path must have over the current SPVPC path before a reroute will be performed. This is analogous to the pnniSpvcRerouteThreshold variable for SPVCCs.rw INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.8.5 |
pnniSpvpcLowestPriorityThe value of lowest priority for SPVPCsrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.8.6 |
pnniSpvpcTrapModeThis configuration item specifies whether the switch should send the: spvcRerouteInitiated OR pnniSpvpcUp and pnniSpvpcFail OR pnniSpvpcDown, pnniSpvpcFail, and pnniSpvpcUp traps.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.8.7 |
pnniSpvpcBackoffIntervalThe time interval to backoff a DTL that failed call setup. The DTL will not be used again until this interval has elapsed. The interval will not be applicable if backoff is disabled on the SPVPC.rw TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.8.8 |
pnniSpvpcSrcTableThis table contains information about SPVPCs (Smart Permanent Virtual Path Connections) that have their source at this switch. This table serves the same function that the pnniSpvcSrcTable serves for SPVCCs. SEQUENCE OF PnniSpvpcSrcEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.9 |
pnniSpvpcSrcEntryA table entry containing source SPVPC (Smart Permanent Virtual Path Connection) information. PnniSpvpcSrcEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1 |
pnniSpvpcSrcIndexThe value of this object uniquely identify the SPVPCs (Smart Permanent Virtual Path Connections) that have this switch as their source. INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.1 |
pnniSpvpcSrcCallingPortThe value of this object identifies the input port of this SPVPC (Smart Permanent Virtual Path Connection), and is the same as the chanrInputPort, chanPort, pathPort, and portNumber. The maximum value of this variable depends on the type of the switch. The upper bound given is the highest possible as of now. In some switches the range will be much narrower.rw INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.2 |
pnniSpvpcSrcCallingVPIThe VPI to be used at the originating switch for the permanent portion of this SPVPC (Smart Permanent Virtual Path Connection).rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.3 |
pnniSpvpcSrcCalledAtmAddrThe ATM address of the distant end NI (destination switch) for this SPVPC (Smart Permanent Virtual Path Connection). Distant end NI is the network interface at the destination switch at which the switched portion of this SPVPC terminates.rw NsapAddr .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.4 |
pnniSpvpcSrcCalledPortThe value of this object identifies the port where the permanent portion of this SPVPC (Smart Permanent Virtual Path Connection) resides at the destination switch. It has a value of -1 if this port at the destination switch cannot be determined.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.5 |
pnniSpvpcSrcCalledVPVCSelThe originating switch for a SPVPC can specify the VPI to be used for the permanent portion of this SPVPC at the destination switch. The value of this object indicates whether the SPVPC was configured with a specific value for this VPI or not. require(2) indicates that the user configured a specific value for this VPI and noPref(1) indicates that the user did not specify any.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.6 |
pnniSpvpcSrcCalledVPIThe VPI to be used at the destination switch for the permanent portion of this SPVPC (Smart Permanent Virtual Path Connection). The range given above is the maximum possible. The upperbound varies with the type of netmod.rw INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.7 |
pnniSpvpcSrcCalledAssignedVPIThe VPI that is assigned at the destination switch for the permanent portion of this SPVPC (Smart Permanent Virtual Path Connection). This value is only meaningful if the SPVPC status is up.ro INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.8 |
pnniSpvpcSrcFwdUpcKeyThe forward UPC traffic contract key for this SPVPC. This traffic contract will be used for the data traffic flow from the originating switch to the destination switch. This key must be defined in the upcContractTable.rw INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.9 |
pnniSpvpcSrcBckUpcKeyThe backward UPC traffic contract key for this SPVPC. This traffic contract will be used for the data flow in the direction from the destination switch to the originating switch. This key must be defined in the upcContractTable.rw INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.10 |
pnniSpvpcSrcSusceptClipThe requested broadband bearer susceptibility to clipping for this SPVPC. This object will be used to fill the broadband bearer capability information element in the call setup message for this SPVPC.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.11 |
pnniSpvpcSrcFwdQoSClassThe requested quality of service class for this SPVPC in the forward (source to destination) direction. This determines the QoS objectives for the data path from the originating switch to the destination switch.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.12 |
pnniSpvpcSrcBckQoSClassThe requested quality of service class for this SPVPC in the backward (destination to source) direction. This object determines the QoS objectives for the data flow in the reverse direction (from the destination switch to the originating switch).rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.13 |
pnniSpvpcSrcLastFailCauseThe last call setup failure cause code for this SPVPC.ro DisplayString .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.14 |
pnniSpvpcSrcRetryCountThe number of times the call setup has been attempted since the SPVPC creation or the last successful call setup for this SPVPC.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.15 |
pnniSpvpcSrcLastChangeTimeThe time since this SPVPC (Smart Permanent Virtual Path Connection) has been up/down in hundredths of a second.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.16 |
pnniSpvpcSrcStatusThe operational status of this SPVPC (Smart Permanent Virtual Path Connection). The value of up(1) indicates that this SPVPC is operational and down(2) indicates that the SPVPC is not-operational.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.17 |
pnniSpvpcSrcNameThe value of this object identifies the name that has been assigned for this SPVPC.rw OCTET STRING .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.18 |
pnniSpvpcSrcRowStatusThe status of this SPVPC (Smart Permanent Virtual Path Connection) entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.19 |
pnniSpvpcSrcRouteCostThe cumulative route cost for the current route of this SPVPC (Smart Permanent Virtual Path Connection).ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.20 |
pnniSpvpcSrcRerouteStatusThe status of the reroute function for this SPVPC (Smart Permanent Virtual Path Connection). If set to disabled(2), no rerouting will be attempted for this SPVPC.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.21 |
pnniSpvpcSrcCallingDomainThe Domain ID identifying the routing domain to be used at the Originating Switch for this SPVPC.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.22 |
pnniSpvpcSrcQosIndexThe index for the QOS Class Expansion Table to be used for QoS class values into QoS parameter objectives for this SPVPC. The corresponding expansion table should be defined in the qosClassExpansionTable.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.23 |
pnniSpvpcSrcPriorityPriority of this SPVPC for connectionrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.24 |
pnniSpvpcSrcLastLocationThe last call setup failure location code for this SPVPC. This indicates the switch that initiated the clearing for the call. This is formatted as a text string with the fields: FMT: Indicates diagnostic format RMT: Indicates whether a remote switch is the source of the failure or this switch inserted the location diag LINK:Link id that clear pertains to VPI: VPI that clear pertains to The remaining fields are format specificro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.25 |
pnniSpvpcSrcOldRouteCostThis OID is specified only to be included the the pnniSpvcUp trap. It specifies the path cost of the call the previous time this call was up. If the call has not been up, this will report a value of -1.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.26 |
pnniSpvpcSrcDownReasonThis OID is specified only to be included the the pnniSpvccDown and pnniSpvccFail traps. This specifies whether the SPVC call was cleared due to a better route being found, a network failure, or SPVPC deletion.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.27 |
pnniSpvpcSrcBackoffStatusThe status of the backoff function for this SPVC (Smart Permanent Virtual Path Circuit). If set to disabled(2), directed dtls configured for this SPVPC will be continually retried on failure.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.28 |
pnniSpvpcSrcActiveDtlIndexThe Active Designated Transit List (DTL) index for this SPVPC (Smart Permanent Virtual Path Circuit). This value along with pnniSpvcSrcActiveDtlNodeIndex uniquely identifies the DTL that is currently used by the SVC portion of the SPVPC.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.29 |
pnniSpvpcSrcActiveDtlNodeIndexThe Node index of the Active Designated Transit List for this SPVPC (Smart Permanent Virtual Path Circuit). The active DTL indexed by the node index and DTL index identifies the DTL that is currently used by the SVC portion of the SPVPC. The value of this object is 65535 for FTPNNI nodes.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.30 |
pnniSpvpcSrcDtlTagThis value specifies an index into a table of DTLs, the DTL entries in this table will be used to setup the SPVPC.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.31 |
pnniSpvpcSrcAutoDtlStatusThe status of the dynamic path selection function for this SPVPC (Smart Permanent Virtual Path Circuit). If set to disabled(2), auto path selection will not be used.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.32 |
pnniSpvpcSrcRGroupIndexThis specifies the entry in the Spvxc Redundancy Group table for information regarding the secondary port to be used as the redundant portrw INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.33 |
pnniSpvpcSrcSecondaryVPIThe Secondary VPI to be used at the originating switch for the redundant permanent portion of this SPVPC.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.9.1.34 |
pnniSpvpcStatsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.6.2.10 |
pnniSpvpcSrcNumberOfSPVPCsThe number of SPVPCs (Smart Permanent Virtual Path Connections) that have their source at this switch. This object is analogous to the pnniSpvcSrcNumberOfSPVCs object defined for SPVCCs.ro Gauge32 .1.3.6.1.4.1.326.2.2.2.1.6.2.10.1 |
pnniSpvpcDestNumberOfSPVPCsThe number of connected SPVPCs (Smart Permanent Virtual Path Connections) that have their destination at this switch. This object is analogous to the pnniSpvcDestNumberOfSPVCs object for SPVCCs.ro Gauge32 .1.3.6.1.4.1.326.2.2.2.1.6.2.10.2 |
pnniSpvpcDestTableThis table contains information about SPVPCs (Smart Permanent Virtual Path Connections) that have their destination at this switch. This table provides the same functions that the pnniSpvcDestTable provides for SPVCCs. SEQUENCE OF PnniSpvpcDestEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.11 |
pnniSpvpcDestEntryA table entry containing destination SPVPC (Smart Permanent Virtual Path Connection) information. PnniSpvpcDestEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.11.1 |
pnniSpvpcDestIndexThe value of this object uniquely identifies the SPVPCs (Smart Permanent Virtual Path Connections) that have this switch as their destination.ro INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.11.1.1 |
pnniSpvpcDestCallingAtmAddrThe ATM address of the calling end NI at the originating switch for this SPVPC (Smart Permanent Virtual Path Connection). Calling end NI is the network interface at the originating switch from which the switched portion of SPVPC originates.ro NsapAddr .1.3.6.1.4.1.326.2.2.2.1.6.2.11.1.2 |
pnniSpvpcDestCallingPortThe value of this object identifies the port of this terminating SPVPC (Smart Permanent Virtual Path Connection) at the source switch in which the permanent portion of the SPVPC resides. It has a value of -1 if the port at the source switch cannot be determined.ro INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.11.1.3 |
pnniSpvpcDestCallingVPIThe VPI to be used at the originating switch for the permanent portion of this SPVPC.ro INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.11.1.4 |
pnniSpvpcDestCalledAtmAddrThe ATM address of the local end NI (at this destination switch) for this SPVPC. Local end NI is network interface at this destination switch where the switched portion of this SPVPC terminates.ro NsapAddr .1.3.6.1.4.1.326.2.2.2.1.6.2.11.1.5 |
pnniSpvpcDestCalledPortThe value of this object identifies the port of this terminating SPVPC (Smart Permanent Virtual Path Connection) at this destination switch where the permanent portion of this SPVPC resides. It has a value of -1 if the port at the destination switch cannot be determined.ro INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.11.1.6 |
pnniSpvpcDestAssignedVPIThe VPI assigned at this destination switch for the permanent portion of this SPVPC. This value is only meaningful if the SPVPC status is up.ro INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.11.1.7 |
pnniSpvpcDestSusceptClipThe value of this object identifies if the SPVPC was setup with the broadband bearer susceptibility to clipping set or not.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.11.1.8 |
pnniSpvpcDestUpTimeThe time since this SPVPC (Smart Permanent Virtual Path Connection) was created in hundredths of a second.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.326.2.2.2.1.6.2.11.1.9 |
pnniSpvpcDestFwdQoSClassThe requested quality of service class for this SPVPC in the direction from the source switch to the destination switch. This value determines the QoS parameter objectives for this SPVPC in that direction.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.11.1.10 |
pnniSpvpcDestBckQoSClassThe requested quality of service class for this SPVPC in the direction from the destination switch to the source switch. This value determines the QoS objectives for the data flow in that direction.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.11.1.11 |
pnniSpvpcDestStatusThe operational status of this SPVPC (Smart Permanent Virtual Path Connection). up(1) indicates that this SPVPC is operational while down(2) indicates that it is not.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.11.1.12 |
pnniSpvpcDestRGroupIndexThis specifies the entry in the Spvxc Redundancy Group table for information regarding the secondary port to be used as the redundant port. This will used at the terminating PVC end.ro INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.11.1.13 |
pnniPmpSpvccGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.6.2.12 |
pnniPmpSpvccSrcNextRootIndexThe index of the next free root index in the pnniPmpSpvcSrcRootTable. Client is responsible for implementing a policy when a set on this variable fails. E.g. Keep testing this variable until a free index is found or choose a random number or a combination of the two.rw TestAndIncr (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.12.1 |
pnniPmpSpvccSrcNumberOfSpvccsThe number of PMP SPVCCs (Smart Permanent Virtual Circuits) that have their source at this switch.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.2 |
pnniPmpSpvccSrcRootTableThis table contains information about the root side of PMP SPVCCs (Smart Permanent Virtual Circuits) that have their source at this switch. It also contains the connection parameters that are common to all the parties SEQUENCE OF PnniPmpSpvccSrcRootEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.12.3 |
pnniPmpSpvccSrcRootEntryA table entry containing source PMP SPVCC (Smart Permanent Virtual Circuits) information. PnniPmpSpvccSrcRootEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1 |
pnniPmpSpvccSrcRootIndexThe value of this object uniquely identify the PMP SPVCCs (Smart Permanent Virtual Circuits) that have this switch as their source(root). Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.1 |
pnniPmpSpvccSrcRootPortThe value of this object identifies the input port of this PMP SPVCC (Smart Permanent Virtual Circuits), and is the same as the chanrInputPort, chanPort, pathPort, and portNumber.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.2 |
pnniPmpSpvccSrcRootVPIThe VPI to be used at the Calling(root) NI for this PMP SPVCC.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.3 |
pnniPmpSpvccSrcRootVCIThe VCI to be used at the Calling(root) NI for this PMP SPVCC.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.4 |
pnniPmpSpvccSrcRootFwdUpcKeyThe forward UPC traffic contract key for this PMP SPVCC. This key must be defined in the upcContractTable. Backward UPC traffic contract does not apply to PMP SPVCCs.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.5 |
pnniPmpSpvccSrcRootBearerClassThe requested broadband bearer class for this PMP SPVCC.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.6 |
pnniPmpSpvccSrcRootSusceptClipThe requested broadband bearer susceptability to for this PMP SPVCC.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.7 |
pnniPmpSpvccSrcRootFwdQoSClassThe requested quality of service for this PMP SPVCC in the forward (calling to called) direction. Backward direction does not apply to PMP SPVCCs.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.8 |
pnniPmpSpvccSrcRootStatusThe operational status of this PMP SPVCC (Smart Permanent Virtual Circuit).ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.9 |
pnniPmpSpvccSrcRootNameThe value of this object identifies the name that has been assigned for this PMP SPVCC.rw OCTET STRING .1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.10 |
pnniPmpSpvccSrcRootPriorityPriority of this PMP SPVCC for connection. This priority is shared with any point-to-point SPVCCs configured on this switch.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.11 |
pnniPmpSpvccSrcRootNumberOfPartiesNumber of parties currently configured with this PMP SPVCCro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.12 |
pnniPmpSpvccSrcRootNextPartyIndexThis indicates the next allocatable party indexrw TestAndIncr (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.13 |
pnniPmpSpvccSrcRootCallingDomainThe Domain ID to be used at the Calling NI for this PMP SPVCC.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.14 |
pnniPmpSpvccSrcRootRowStatusThe status of this SPVCC (Smart Permanent Virtual Circuits) entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.15 |
pnniPmpSpvccSrcRootRGroupIndexThis specifies the entry in the Spvxc Redundancy Group table for information regarding the secondary port to be used as the redundant portrw INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.16 |
pnniPmpSpvccSrcRootSecondaryVPIThe Secondary VPI to be used at the originating switch for the redundant permanent portion of this SPVC.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.17 |
pnniPmpSpvccSrcRootSecondaryVCIThe Secondary VCI to be used at the originating switch for the redundant permanent portion of this SPVC.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.3.1.18 |
pnniPmpSpvccSrcPartyTableThis table contains information about the parties of PMP SPVCCs (Smart Permanent Virtual Circuits) that have their source at this switch. SEQUENCE OF PnniPmpSpvccSrcPartyEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.12.4 |
pnniPmpSpvccSrcPartyEntryA table entry containing information about parties in a PMP SPVCC (Smart Permanent Virtual Circuits) at the source. PnniPmpSpvccSrcPartyEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1 |
pnniPmpSpvccSrcPartyIndexThe value of this object uniquely identifies a party within a PMP SPVCC identified by pnniPmpSpvccSrcRootIndex. Root's parameters and commmon connection parameters for this party are availabe in pnniPmpSpvccSrcRootTable, indexed by pnniPmpSpvccSrcRootIndex. Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.1 |
pnniPmpSpvccSrcPartyAtmAddrThe ATM address of the distant end NI (remote switch) for this party.rw NsapAddr .1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.2 |
pnniPmpSpvccSrcPartyVPVCSelThe Called VPI/VCI value selection qualifier.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.3 |
pnniPmpSpvccSrcPartyVPIThe VPI to be used at the Called NI for this party.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.4 |
pnniPmpSpvccSrcPartyVCIThe VCI to be used at the Called NI for this party.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.5 |
pnniPmpSpvccSrcPartyAssignedVPIThe VPI assigned at the Called NI for this party. This value is only meaningful if the party status is up.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.6 |
pnniPmpSpvccSrcPartyAssignedVCIThe VCI assigned at the Called NI for this party. This value is only meaningful if the party status is up.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.7 |
pnniPmpSpvccSrcPartyStatusOperational status of this party in the PMP SPVCC.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.8 |
pnniPmpSpvccSrcPartyNameThe value of this object identifies the name that has been assigned for this party.rw OCTET STRING .1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.9 |
pnniPmpSpvccSrcPartyLastFailCauseThe last setup(addparty) failure cause code for this party.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.10 |
pnniPmpSpvccSrcPartyRetryCountThe number of times the party setup/addparty has been attempted since the party creation or the last successful setup/addparty.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.11 |
pnniPmpSpvccSrcPartyLastChangeTimeThe time since this party has been up/down in hundredths of a second.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.12 |
pnniPmpSpvccSrcPartyFtDtlIndexThe Designated Transit List (DTL) index for this party. This value must be defined in the ftPnniDTLTable. The DTL specifies a preferred call routing for the SVC portion of the party. If a DTL is specified, this party will not be rerouted when rerouting is requested administratively.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.13 |
pnniPmpSpvccSrcPartyRerouteStatusThe status of the reroute function for this party. Rerouting can be administratively requested, for active parties, by setting this variable to reroute_requested(2). On successful completion of rerouting, it will be set to reroute_completed(3). When a DTL is specified for a party, rerouting will not be performed for that party and this variable will set to reroute_not_applicable.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.14 |
pnniPmpSpvccSrcPartyQosIndexThe index for the QOS Class Expansion Table to be used for this PMP SPVCC.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.15 |
pnniPmpSpvccSrcPartyRowStatusThe status of this party entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.16 |
pnniPmpSpvccSrcPartyLastLocationThe last call setup failure location code for this SPVC. This indicates the switch that initiated the clearing for the call. This is formatted as a text string with the fields: FMT: Indicates diagnostic format RMT: Indicates whether a remote switch is the source of the failure or this switch inserted the location diag LINK:Link id that clear pertains to VPI: VPI that clear pertains to The remaining fields are format specificro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.17 |
pnniPmpSpvccSrcPartyAutoDtlStatusThe status of the dynamic path selection function for this SPVC (Smart Permanent Virtual Circuit). If set to disabled(2), auto path selection will not be used.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.18 |
pnniPmpSpvccSrcPartyDownReasonThe reason for the spvc down is set accordinglyro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.19 |
pnniPmpSpvccSrcPartyRouteCostThe link cost associated for the party isset herero Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.4.1.20 |
pnniPmpSpvccDestNumberOfSpvccsThe number of connected PMP SPVCCs (Smart Permanent Virtual Circuits) that have their parties terminating at this switch.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.5 |
pnniPmpSpvccDestRootTableThis table contains information about the root of PMP SPVCCs (Smart Permanent Virtual Circuits) that have their parties terminating at this switch. SEQUENCE OF PnniPmpSpvccDestRootEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.12.6 |
pnniPmpSpvccDestRootEntryA table entry containing destination SPVCC (Smart Permanent Virtual Circuits) information. PnniPmpSpvccDestRootEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.12.6.1 |
pnniPmpSpvccDestRootIndexThe value of this object uniquely identifies the PMP SPVCCs (Smart Permanent Virtual Circuits) that has one or more parties terminating at this switch.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.6.1.1 |
pnniPmpSpvccDestRootAtmAddrThe ATM address of the root of the PMP SPVCC that has one or more parties terminating at this switch.ro NsapAddr .1.3.6.1.4.1.326.2.2.2.1.6.2.12.6.1.2 |
pnniPmpSpvccDestRootPortThe value of this object identifies the port of this terminating PMP SPVCC (Smart Permanent Virtual Circuits) at the source end. It has a value of -1 if the port at the destination switch cannot be determined.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.6.1.3 |
pnniPmpSpvccDestRootVPIThe VPI used for the PVCC portion of the connection at the root of the PMP SPVCC. The root switch is identified by pnniPmpSpvccDestCallingAtmAddr.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.6.1.4 |
pnniPmpSpvccDestRootVCIThe VCI used for the PVCC portion of the connection at the root of the PMP SPVCC. The root switch is identified by pnniPmpSpvccDestCallingAtmAddr.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.6.1.5 |
pnniPmpSpvccDestRootBearerClassThe broadband bearer class signalled for the first party of this PMP SPVCC. All subsequent parties should have the same value.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.12.6.1.6 |
pnniPmpSpvccDestRootSusceptClipThe broadband bearer susceptability to clipping signalled for the first party of this PMP SPVCC. All subsequent parties should have the same value.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.12.6.1.7 |
pnniPmpSpvccDestRootFwdQoSClassThe requested quality of service for this PMP SPVCC in the forward (from root to leaves) direction. Backward QoS requirements do not apply to PMP SPVCCs.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.12.6.1.8 |
pnniPmpSpvccDestRootNumberOfPartiesNumber of parties currently terminating at this switch within this PMP SPVCCro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.6.1.9 |
pnniPmpSpvccDestPartyTableThis table contains information about the parties of PMP SPVCCs (Smart Permanent Virtual Circuits) that terminate at this switch. SEQUENCE OF PnniPmpSpvccDestPartyEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.12.7 |
pnniPmpSpvccDestPartyEntryA table entry containing destination information about parties in a PMP SPVCC (Smart Permanent Virtual Circuits). PnniPmpSpvccDestPartyEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.12.7.1 |
pnniPmpSpvccDestPartyIndexThe value of this object uniquely identifies a party of PMP SPVCCs (Smart Permanent Virtual Circuits) that have one or more parties terminating at this switch. This value is unique within a PMP SPVCC represented by pnniPmpSpvccDestRootIndexro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.7.1.1 |
pnniPmpSpvccDestPartyAtmAddrThe ATM address of the switch where this party of a PMP SPVCC terminates.ro NsapAddr .1.3.6.1.4.1.326.2.2.2.1.6.2.12.7.1.2 |
pnniPmpSpvccDestPartyPortThe value of this object identifies the port where this party of a PMP SPVCC (Smart Permanent Virtual Circuits) terminates.It has a value os -1 if the port at the destination switch cannot be determined.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.7.1.3 |
pnniPmpSpvccDestPartyAssignedVPIThe value of this object identifies the VPI assigned for this party of a PMP SPVCC (Smart Permanent Virtual Circuits) at the terminating switch. This value is only meaningful if the party status, identified by pnniPmpSpvccDestStatus, is up.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.7.1.4 |
pnniPmpSpvccDestPartyAssignedVCIThe value of this object identifies the VCI assigned for this party of a PMP SPVCC (Smart Permanent Virtual Circuits) at the terminating switch. This value is only meaningful if the party status, identified by pnniPmpSpvccDestStatus, is up.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.12.7.1.5 |
pnniPmpSpvccDestPartyUpTimeThe time since this party of PMP SPVCC (Smart Permanent Virtual Circuits) was created in hundredths of a second.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.326.2.2.2.1.6.2.12.7.1.6 |
pnniPmpSpvccDestPartyTransitNetSelThe optional transit network selection for this party of PMP SPVCC.ro TransitNetwork .1.3.6.1.4.1.326.2.2.2.1.6.2.12.7.1.7 |
pnniPmpSpvccDestPartyStatusThe operational status of this party of PMP SPVCC (Smart Permanent Virtual Circuit).ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.12.7.1.8 |
pnniPmpSpvccDestPartyRGroupIndexThis specifies the entry in the Spvxc Redundancy Group table for information regarding the secondary port to be used as the redundant port. This will used at the terminating PVC end.ro INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.12.7.1.9 |
vpciMappingTableGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.6.2.13 |
vmtVpciMapTableA table of VPCI, VPI and Port mappings. SEQUENCE OF VmtVpciMapEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.13.1 |
vmtVpciMapEntryA table entry containing a VPCI, VPI and Port mappings. VmtVpciMapEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.13.1.1 |
vmtVpciMapIndexThe value of this object identifies the VPCI mapping associated with this entry. INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.13.1.1.1 |
vmtVpciMapVPCIThe VPCI associated with this VPCI mapping entry.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.13.1.1.2 |
vmtVpciMapVPIThe VPI associated with this VPCI mapping entry. A value of -1 indicates that the VPI is the same as the VPI associated with the signalling interface using this VPCI mapping entry.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.13.1.1.3 |
vmtVpciMapPortThe Port associated with this VPCI mapping entry. A value of -1 indicates that the Port is the same as the Port associated with the signalling interface using this VPCI mapping entry.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.13.1.1.4 |
vmtVpciMapStatusThe status of this VPCI mapping entry. The status cannot be set to destroy if there are any vmtVpciMapGroupTable entries that refer to it.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.13.1.1.5 |
vmtVpciMapGroupTableA table of VPCI mapping groups. Each VPCI mapping group consists of a list if VPCI mapping entries. SEQUENCE OF VmtVpciMapGroupEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.13.2 |
vmtVpciMapGroupEntryA table entry for one VPCI mapping group. VmtVpciMapGroupEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.13.2.1 |
vmtVpciMapGroupIndexThe value of this object identifies the VPCI mapping group associated with this entry. INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.13.2.1.1 |
vmtVpciMapGroupStatusThe status of the VPCI mapping group entry. This object cannot be transitioned from the Active state to any other state if there are any signalling interfaces using this VPCI mapping group. Setting this variable to destroy will remove this row from the vmtVpciMapGroupTable and also remove the corresponding entries from the vmtVpciMapListTable.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.13.2.1.2 |
vmtVpciMapListTableA table of VPCI mapping entries for VPCI mapping groups. A VPCI mapping list is composed of a list of VPCI mapping entries. All objects with the same value for vmtVpciMapGroupIndex are conceptually part of the same vmtVpciMapGroupEntry. Entries in this table may be added, deleted or modified only if the corresponding vpcigroup index is not being used by any signalling interface. SEQUENCE OF VmtVpciMapListEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.13.3 |
vmtVpciMapListEntryA table entry holding one VPCI mapping entry in a VPCI mapping group. VmtVpciMapListEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.13.3.1 |
vmtVpciMapListIndexThe value of this object identifies the order of a VPCI mapping entry in the VPCI mapping group in which it is used. INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.13.3.1.1 |
vmtVpciMapListMEIndexThe value of this object identifies the VPCI mapping entry in the vmtVpciMapTable for this entry.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.13.3.1.2 |
vmtVpciMapListStatusThe status of this entry. This object can be set to destroy only if the corresponding vmtVpciMapGroupStatus is not Active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.13.3.1.3 |
pnniSpvxcRGroupTableA table of Primary to Secondary Port mappings that will be used for redundancy in permanent portion of SPVxCs. SEQUENCE OF PnniSpvxcRGroupEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.14 |
pnniSpvxcRGroupEntryA table entry containing the primary to secondary port mappings. PnniSpvxcRGroupEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.14.1 |
pnniSpvxcRGroupIndexThe value of this object identifies the Group Index associated with this entry. INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.14.1.1 |
pnniSpvxcRGroupPrimaryPortThe value of this object identifies the primary port of this entry. This will used as the primary PVC port for the SPVC created with this group index.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.14.1.2 |
pnniSpvxcRGroupSecondaryPortThe value of this object identifies the secondary port of this group. This will used as the redundant PVC port for the SPVC created with this group index. During a switch command, the PVCs will be switched from primary port to this port.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.14.1.3 |
pnniSpvxcRGroupNsapAddrThis shows the default nsap address associated with this group using the default domain's prefix. This is a read-only variable available to view the default nsap address associated with this group.ro NsapAddr .1.3.6.1.4.1.326.2.2.2.1.6.2.14.1.4 |
pnniSpvxcRGroupSwitchoverCmdThe value of this MIB defines the switchover command. The value of 1 is used to switch over the permanent PVC portion to the primary port. The value of 2 is used to switch over the permanent PVC portion to the secondary port. If the permanent portions are already on the specified port, no action is takenrw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.14.1.5 |
pnniSpvxcRGroupActivePortThis specifies the port that is active. This can take any one of the primary or secondary port values. This is a read only variable useful to check the currently active port.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.14.1.6 |
pnniSpvxcRGroupPacingNumberThis specifies the pacing number for this group. During a pacing interval, pacing number of SPVCs will be attempted for PVC switch over.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.14.1.7 |
pnniSpvxcRGroupPacingIntervalThis specifies the pacing interval in units of milliseconds for this group. Every time a switchover command is issued, pacing number of SPVCs will be attempted for PVC switch over every Pacing Interval.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.14.1.8 |
pnniSpvxcRGroupAutoPVCSwitchoverThe value of this MIB defines if automatic switchover of the PVC portion is enable dor disabled. The default value is disabled(2).rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.14.1.9 |
pnniSpvxcRGroupNameThe value of this object identifies the name that has been assigned for this Rgroup.rw OCTET STRING .1.3.6.1.4.1.326.2.2.2.1.6.2.14.1.10 |
pnniSpvxcRGroupStateThis specifies the state of the Redundancy Group. State operational(1) indicates that this group is in the normal state and switchover is not going on. State switchover_in_progress(2) indicates that switchover is presently going on for this group. In this state no new SPVCs can be added to this group.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.6.2.14.1.11 |
pnniSpvxcRGroupRowStatusThe status of this pnniSpvxcRGroup entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.14.1.12 |
proxyDirMapEntryGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.6.2.15 |
proxyDirMapEntryTableA table of ATM End system address, Proxy address directory and VPCI mappings. SEQUENCE OF ProxyDirMapEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.15.1 |
proxyDirMapEntryA table entry containing ATM End System Address, proxy directory group index and VPCI. ProxyDirMapEntry .1.3.6.1.4.1.326.2.2.2.1.6.2.15.1.1 |
proxyDirMapIndexThe value of this object identifies the mapping associated with this entry. INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.15.1.1.1 |
proxyDirMapAESAThe ATM End System Address associated with this entryrw OCTET STRING .1.3.6.1.4.1.326.2.2.2.1.6.2.15.1.1.2 |
proxyDirMapGroupThe proxy directory address group identifier associated with this mappingrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.15.1.1.3 |
proxyDirMapVPCIThe VPCI value associated with this entryrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.15.1.1.4 |
proxyDirMapStatusThe status of this mapping entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.15.1.1.5 |
proxyDirMapVpThe VP value associated with this entryro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.15.1.1.6 |
proxyDirMapPortThe port associated with this entryro Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.15.1.1.7 |
proxyDirGroupGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.6.2.16 |
proxyDirGroupTableA group of ATM End system address and VPCI mappings SEQUENCE OF ProxyDirGroup .1.3.6.1.4.1.326.2.2.2.1.6.2.16.1 |
proxyDirGroupEntryA group of ATM End system address and VPCI mappings ProxyDirGroup .1.3.6.1.4.1.326.2.2.2.1.6.2.16.1.1 |
proxyDirGroupIndexThe value of this object identifies the mapping associated with this entry. INTEGER .1.3.6.1.4.1.326.2.2.2.1.6.2.16.1.1.1 |
proxyDirGroupPrefixThe prefix of the ATM End System Address that is used in mapping to a VPCIrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.16.1.1.2 |
proxyDirGroupVPCIGroupThe VPCI group index associated with this entryrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.6.2.16.1.1.3 |
proxyDirGroupStatusThe status of this mapping entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.6.2.16.1.1.4 |
swBoardGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.7 |
swBoardTableA table of ATM switch cluster configuration information. SEQUENCE OF SwBoardEntry .1.3.6.1.4.1.326.2.2.2.1.7.1 |
swBoardEntryA table entry containing ATM switch cluster information, index by the switch board. SwBoardEntry .1.3.6.1.4.1.326.2.2.2.1.7.1.1 |
swBoardIndexThe index of this switch board within the ATM switch cluster.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.7.1.1.1 |
swBoardMaxPathsThe maximum number of input VPIs (Virtual Path Identifier) on this switch board.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.7.1.1.2 |
swBoardMaxChannelsThe maximum number of input VCIs (Virtual Channel Identifiers) on this switch board.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.7.1.1.3 |
swBoardAtmAddressThe address of this ATM switch board.ro SpansAddress .1.3.6.1.4.1.326.2.2.2.1.7.1.1.4 |
swBoardUptimeThe length of time this ATM switch board has been up, in hundredths of a second.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.326.2.2.2.1.7.1.1.5 |
swBoardCDVThe switch board Cell Delay Variation (CDV) specified in microseconds, indicates the time window in which a cell may be received on a connection and be accepted. A cell that is received on a connection outside the CDV window will be tagged or dropped as indicated by the swBoardPolicingAction object. The boardCDV is the default CDV for all the connection on this switch board. Individual connections can be set to explicitly override this value.rwdeprecated Integer32 .1.3.6.1.4.1.326.2.2.2.1.7.1.1.6 |
swBoardPolicingActionThis object indicates the action the switch board will take in case of bandwidth violation. The swBoardPolicingAction is the default policing action for all the connections on this switch board. Individual connections can be set to explicitly override this default action.rwdeprecated Enumeration .1.3.6.1.4.1.326.2.2.2.1.7.1.1.7 |
swBoardNsapPrefixThe default NSAP (Network Service Access Point) prefix for this ATM switch board. The NSAP prefix will be used in the ILMI address registration message as well as the 'hello-indication' SPANS-NNI message.rw NsapPrefix .1.3.6.1.4.1.326.2.2.2.1.7.1.1.8 |
swBoardClockScalingFactorThis specifies the value written into the switch boards Time Scaling Factor register. See Sec. 3.2.1 for more info. The Time Scaling Factor is an 8-bit register that determines the number of 25ns clock cycles that occur between increments of the Time and Interrupt Timer Reigsters. Increasing the Time Scale Factor increases the burst tolerance that can be represented by the policer (in multiples of .838 seconds) while reducing the precision of the policer by a similar factor. The possible values for this variable are 1 through 255.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.7.1.1.9 |
swBoardDebugModeThis object indicates whether or not debugging services are available for this switch.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.7.1.1.10 |
swBoardMulticastModeThis object identifies the mode in which this ATM switch board is operating. Extended-mode provides greater flexibility when selecting VCI for point to multipoint connections. Non-extended (mixed) mode is more restrictive. If any series A or B netmods are present, the switch board should operate in non-extended mode.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.7.1.1.11 |
swBoardFingerModeThis object indicates whether or not finger services are available for this switch.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.7.1.1.12 |
swBoardATMLayerOAMThis object specifies whether the processing of ATM layer OAM cells by this switch board is enabled or disabled.rwdeprecated Enumeration .1.3.6.1.4.1.326.2.2.2.1.7.1.1.13 |
swBoardTopologyGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.8 |
swBoardTopoTableA table of switch board topology general information. SEQUENCE OF SwBoardTopoEntry .1.3.6.1.4.1.326.2.2.2.1.8.1 |
swBoardTopoEntryA table entry containing switch board topology information. SwBoardTopoEntry .1.3.6.1.4.1.326.2.2.2.1.8.1.1 |
swBoardTopoIndexThe index of this switch board within the ATM switch cluster. This object should be the same as the swBoardIndex.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.8.1.1.1 |
swBoardTopoNumberOfLinksCurrent number of inter-switch links known by this switch board.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.8.1.1.2 |
swBoardLinkTableA table of ATM links that are known to a given switch board in the switch cluster. If all boards in the switch cluster are interconnected, all swBoardLinkEntries will be identical. SEQUENCE OF SwBoardLinkEntry .1.3.6.1.4.1.326.2.2.2.1.8.2 |
swBoardLinkEntryA table entry containing link information known to a given switch board. SwBoardLinkEntry .1.3.6.1.4.1.326.2.2.2.1.8.2.1 |
swBoardLinkIndexThe index of this switch board within the ATM switch cluster. This object should be the same as the swBoardIndex.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.8.2.1.1 |
swBoardLinkSrcThe ATM address of the source switch of this link.ro SpansAddress .1.3.6.1.4.1.326.2.2.2.1.8.2.1.2 |
swBoardLinkDestThe ATM address of the destination switch of this link.ro SpansAddress .1.3.6.1.4.1.326.2.2.2.1.8.2.1.3 |
swBoardLinkCapacityThe free capacity of this link in kilobits per second.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.8.2.1.4 |
swBoardLinkAgeThe freshness of the information about this link. The actual value has no units associated with it. It should be used for comparison.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.8.2.1.5 |
nsapGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.9 |
nsapNetworkPrefixTableA table of Network Prefix addresses SEQUENCE OF NsapNetworkPrefixEntry .1.3.6.1.4.1.326.2.2.2.1.9.1 |
nsapNetworkPrefixEntryAn entry in the Network Prefix table. NsapNetworkPrefixEntry .1.3.6.1.4.1.326.2.2.2.1.9.1.1 |
nsapNetworkPrefixPortThe value of this object identifies the port of this signalling path, and is the same as nsapPort.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.1.1.1 |
nsapNetworkPrefixVPIThe value of this object identifies the VPI (Virtual Path Identifier) of this signaling path statistics entry, and is the same as nsapVPI.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.1.1.2 |
nsapNetworkPrefixValueThe network prefix for ATM addresses which is in effect on the user-side of the ATM UNI port.ro NsapPrefix .1.3.6.1.4.1.326.2.2.2.1.9.1.1.3 |
nsapNetworkPrefixStatusThe status of this Network Prefix entry. Setting this object to invalid(4) causes this Network to disappear.rw EntryStatus .1.3.6.1.4.1.326.2.2.2.1.9.1.1.4 |
nsapTopologyTableA table for NSAP (Network Service Access Point) topology, based on NSAP routing. SEQUENCE OF NsapTopologyEntry .1.3.6.1.4.1.326.2.2.2.1.9.3 |
nsapTopologyEntryAn entry in the NSAP (Network Service Access Point) topology table. NsapTopologyEntry .1.3.6.1.4.1.326.2.2.2.1.9.3.1 |
nsapTopoBoardThe index of the switch board within the ATM switch cluster. This object is the same as the swBoardIndex.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.3.1.1 |
nsapTopoLinkSrcThe value of this object identifies the source NSAP (Network Service Access Point) address of this link.ro NsapAddr .1.3.6.1.4.1.326.2.2.2.1.9.3.1.2 |
nsapTopoLinkSrcMaskThe value of this object identifies the mask that is used for the link source NSAP (Network Service Access Point) address. The mask identifies the number of bits in the NSAP address that are valid. The value of the mask object is in the range 0-160 (160 bits is the size of an NSAP address).ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.3.1.3 |
nsapTopoLinkSrcPortThis object identifies the physical port of the link source.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.3.1.4 |
nsapTopoLinkSrcVpiThis object identifies the virtual path identifier of the link source.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.3.1.5 |
nsapTopoLinkDestThe value of this object identifies the destination NSAP (Network Service Access Point) address of this link.ro NsapAddr .1.3.6.1.4.1.326.2.2.2.1.9.3.1.6 |
nsapTopoLinkDestMaskThe value of this object identifies the mask that is used for the link destination NSAP (Network Service Access Point) address. The mask identifies the number of bits in the NSAP address that are valid. The value of the mask object is in the range 0-160 (160 bits is the size of an NSAP address).ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.3.1.7 |
nsapTopoLinkDestPortThis object identifies the physical port of the link destination.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.3.1.8 |
nsapTopoLinkDestVpiThis object identifies the virtual path identifier of the link destination.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.3.1.9 |
nsapTopoLinkCostThe routing metric for this link.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.3.1.10 |
nsapTopoLinkUbrVCsThe number of UBR vcs.rodeprecated Gauge32 .1.3.6.1.4.1.326.2.2.2.1.9.3.1.11 |
nsapTopoLinkCbrCapacityThe available capacity for additional CBR (Constant Bit Rate) connections. The available capacity is measured in Kbps.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.3.1.12 |
nsapTopoLinkCbrFifoThe size of the FIFO queue that is used for transmitting CBR (Constant Bit Rate) traffic. The size of the fifo is measured in number of cells.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.3.1.13 |
nsapTopoLinkVbrCapacityThe available capacity for additional VBR (Variable Bit Rate) connections. The available capacity is measured in Kbps.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.3.1.14 |
nsapTopoLinkVbrFifoThe size of the FIFO queue that is used for transmitting VBR (Variable Bit Rate) traffic. The size of the fifo is measured in number of cells.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.3.1.15 |
nsapTopoLinkOrigThe source of this route information.ro Enumeration .1.3.6.1.4.1.326.2.2.2.1.9.3.1.16 |
nsapTopoLinkCapabilitySetA bitmap indicate the capabilities of this link. For example, whether the link support ABR (Available Bit Rate) traffic.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.3.1.17 |
nsapTopoLinkFreshnessThis object indicates the freshness (or staleness) of this NSAP (Network Service Access Point) link. As the number increases, the link becomes stale.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.3.1.18 |
nsapTopoLinkUbrEstimatedBandwidthThe estimated UBR bandwidth on this link.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.3.1.19 |
nsapStaticRouteTableA table for static NSAP (Network Service Access Point) route administration. SEQUENCE OF NsapStaticRouteEntry .1.3.6.1.4.1.326.2.2.2.1.9.4 |
nsapStaticRouteEntryAn entry in the NSAP (Network Service Access Point) static route administration table. NsapStaticRouteEntry .1.3.6.1.4.1.326.2.2.2.1.9.4.1 |
nsapStaticRouteAddressThe value of this object identifies the destination NSAP addressro NsapAddr .1.3.6.1.4.1.326.2.2.2.1.9.4.1.1 |
nsapStaticRouteMaskThe value of this object identifies the mask that is used for this NSAP (Network Service Access Point) address.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.4.1.2 |
nsapStaticRoutePortThe value of this object identifies the port through which this NSAP (Network Service Access Point) address can be reached.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.4.1.3 |
nsapStaticRouteVPIThe value of this object identifies the path through which this NSAP (Network Service Access Point) address can be reached.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.4.1.4 |
nsapStaticRouteCostThe value of this object identifies the cost associated with this Static Route. This cost is to be used as a metric while routingrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.4.1.5 |
nsapStaticRouteMaxCbrCapThe value of this object identifies the maximum capacity available on this route for CBR connectionsrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.4.1.6 |
nsapStaticRouteMaxVbrCapThe value of this object identifies the maximum capacity available on this route for VBR connectionsrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.4.1.7 |
nsapStaticRouteAbrSupportThe value identifies the capability to support ABR traffic on this routerw Enumeration .1.3.6.1.4.1.326.2.2.2.1.9.4.1.8 |
nsapStaticRouteEpdSupportThe value identifies the capability to support Early Packet Discard (EPD) on this routerw Enumeration .1.3.6.1.4.1.326.2.2.2.1.9.4.1.9 |
nsapStaticRouteStatusThe status of this NSAP (Network Service Access Point) address. Setting this object to invalid(4) causes this NSAP address to disappear.rw EntryStatus .1.3.6.1.4.1.326.2.2.2.1.9.4.1.10 |
ftPnniDTLTableA table of Designated Transit List entries. The DTLs represent statically configured FT-PNNI routesdeprecated SEQUENCE OF FtPnniDTLEntry .1.3.6.1.4.1.326.2.2.2.1.9.5 |
ftPnniDTLEntryAn entry in the FT-PNNI DTLble. A DTL is formed by concatenating rows of the table for which the ftPnniDTLIndex is the samedeprecated FtPnniDTLEntry .1.3.6.1.4.1.326.2.2.2.1.9.5.1 |
ftPnniDTLIndexThe value of this object identifies the index of a (FT-PNNI) DTL in the table. A DTL (Designated Transit List) is a source route of entries comprising a FT-PNNI node and the corresponding logical output port at that node. The FT-PNNI node is given by the node's NSAP Prefix and mask. The logical port is given by the linkid and the VPI.rodeprecated Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.5.1.1 |
ftPnniDTLEntryIndexThe value of this object identifies the Index of an entry within a given DTL. A DTL is a source route and each entry in the DTL represents a single hop in the source route. Each hop is represented by a FT-PNNI node and the logical output port at that node. An entry in the DTL is given an index equal to its position in the source route. Thus the entry corresponding to the first hop is given an index of 1, the second hop an index of 2 and so on.rodeprecated Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.5.1.2 |
ftPnniDTLNodePrefixThis the Prefix part of the Node ID of this DTL entry. In FT-PNNI, The Node IDs are represented as prefixes, that represents both the ID of the node and a summary of reachable addressesrwdeprecated NsapPrefix .1.3.6.1.4.1.326.2.2.2.1.9.5.1.3 |
ftPnniDTLNodeMaskThis the Mask corresponding to the ftPnniDTLNodePrefix. This gives the length of the above prefix in number of bits. This can vary from 0 to 104 (13 bytes).rwdeprecated INTEGER .1.3.6.1.4.1.326.2.2.2.1.9.5.1.4 |
ftPnniDTLPortThis is the output port at the Node given by the above Node ID. This is also the port to which the next node in the DTL (if there is one) is connected.rwdeprecated Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.5.1.5 |
ftPnniDTLVPIThis is the output path in the output port above that is the signalling path to the peer given by the next node in the DTL.rwdeprecated Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.5.1.6 |
ftPnniDTLStatusThe entry status of this entry in the table.rwdeprecated EntryStatus .1.3.6.1.4.1.326.2.2.2.1.9.5.1.7 |
ftPnniSummaryTableA table of Prefixes that are used for either summarizing or suppressing internal and exterior reachability information by the FT-PNNI routing protocoldeprecated SEQUENCE OF FtPnniSummaryEntry .1.3.6.1.4.1.326.2.2.2.1.9.6 |
ftPnniSummaryEntryAn entry in the FT-PNNI Summary table.deprecated FtPnniSummaryEntry .1.3.6.1.4.1.326.2.2.2.1.9.6.1 |
ftPnniSummaryAddressThe address prefix that is to be either summarized or suppressed by the FT-PNNI routing protocolrodeprecated Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.6.1.1 |
ftPnniSummaryPrefixLengthThis value is the mask for the address. This gives length of the address prefix in number of bitsrodeprecated Integer32 .1.3.6.1.4.1.326.2.2.2.1.9.6.1.2 |
ftPnniSummaryTypeThis value identifies the type of the summary being describedrwdeprecated Enumeration .1.3.6.1.4.1.326.2.2.2.1.9.6.1.3 |
ftPnniSummarySuppressThe Suppress flag determinces what is to be done with this address. The default value (no) will indicate that the summary should be propagated. If the value is yes, this summary and any reachable address it summarizes are suppressed for being propagatedrwdeprecated Enumeration .1.3.6.1.4.1.326.2.2.2.1.9.6.1.4 |
ftPnniSummaryStateThis value indicates whether the summary is currently being advertised by the FT-PNNI routing protocolrodeprecated Enumeration .1.3.6.1.4.1.326.2.2.2.1.9.6.1.5 |
ftPnniSummaryStatusThe entry status of this entry in the table.rwdeprecated EntryStatus .1.3.6.1.4.1.326.2.2.2.1.9.6.1.6 |
upcContractGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.10 |
upcContractTableA table of user defined UPC traffic contracts. SEQUENCE OF UpcContractEntry .1.3.6.1.4.1.326.2.2.2.1.10.1 |
upcContractEntryA table entry containing a user defined UPC traffic contract. UpcContractEntry .1.3.6.1.4.1.326.2.2.2.1.10.1.1 |
upcContractKeyThe key of this UPC configuration.ro INTEGER .1.3.6.1.4.1.326.2.2.2.1.10.1.1.1 |
upcContractEntryStatusThe SNMP status of this upcContract entry.rw EntryStatus .1.3.6.1.4.1.326.2.2.2.1.10.1.1.2 |
upcContractPCR01The peak cell rate (cells/sec) for cell loss priority 0+1rwdeprecated Integer32 .1.3.6.1.4.1.326.2.2.2.1.10.1.1.3 |
upcContractSCR01The sustained cell rate (cells/sec) for cell loss priority 0+1rwdeprecated Integer32 .1.3.6.1.4.1.326.2.2.2.1.10.1.1.4 |
upcContractMBS01The maximum burst size (cells) for cell loss priority 0+1rwdeprecated Integer32 .1.3.6.1.4.1.326.2.2.2.1.10.1.1.5 |
upcContractPCR0The peak cell rate (cells/sec) for cell loss priority 0rwdeprecated Integer32 .1.3.6.1.4.1.326.2.2.2.1.10.1.1.6 |
upcContractSCR0The sustained cell rate (cells/sec) for cell loss priority 0rwdeprecated Integer32 .1.3.6.1.4.1.326.2.2.2.1.10.1.1.7 |
upcContractMBS0The maximum burst size (cells) for cell loss priority 0.rwdeprecated Integer32 .1.3.6.1.4.1.326.2.2.2.1.10.1.1.8 |
upcContractCDVTThe Cell Delay Variation Tolerance associated with PCR's. The Default CDVT values (in microseconds) for the various physical media are: DS1_DEFAULT_LINK_CDVT - 5000 DS3_DEFAULT_LINK_CDVT - 2500 E1_DEFAULT_LINK_CDVT - 5000 E3_DEFAULT_LINK_CDVT - 2500 J2_DEFAULT_LINK_CDVT - 5000 SONET_OC3_LINK_DEFAULT_CDVT - 250 SONET_OC12_LINK_DEFAULT_CDVT - 250 SONET_OC48_LINK_DEFAULT_CDVT - 250 TAXI_DEFAULT_LINK_CDVT - 1000 TP25_DEFAULT_LINK_CDVT - 5000 CTRLPORT_DEFAULT_LINK_CDVT - 5000 BACKPLANE_DEFAULT_LINK_CDVT - 100rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.10.1.1.9 |
upcContractTagReqShould we tag (instead of drop) non-compliant CLP=0 cells?.rwdeprecated Integer32 .1.3.6.1.4.1.326.2.2.2.1.10.1.1.10 |
upcContractAal5EpdShould we do AAL5 EPD on this connection?. This variable has been subsumed by the two new variables upcContractIsAAL5 and upcContractdoPacketDiscard. These new variables allow us to decouple the AAL5'ness of a connection from whether we are going to do packet discard on it if it is AAL5.rwdeprecated Integer32 .1.3.6.1.4.1.326.2.2.2.1.10.1.1.11 |
upcContractNameThe name associated with this UPC traffic contract.rw DisplayString .1.3.6.1.4.1.326.2.2.2.1.10.1.1.12 |
upcContractDoGCRAPolicingShould we suppress GCRA policing on connections using this UPC Contract ?rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.10.1.1.13 |
upcContractIsAAL5Is this UPC contract using AAL5?rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.10.1.1.14 |
upcContractDoPacketDiscardShould we perform AAL5 Packet Discard (EPD/PPD) on this UPC contract. This variable only has meaning if the connection is also AAL5rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.10.1.1.15 |
upcContractDoPPPolicingShould we perform AAL5 Partial Packet Policing on this UPC contract. This variable only has meaning if the connections is also AAL5.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.10.1.1.16 |
upcContractDoUBRTaggingShould we perform tagging (set CLP=1) of all cells of connections that use this UBR traffic contract?rwdeprecated Enumeration .1.3.6.1.4.1.326.2.2.2.1.10.1.1.17 |
upcContractSchedModeThis variable indicates the scheduling mode that is requested for connections that use this UPC contract.rw AtmConnSchedMode .1.3.6.1.4.1.326.2.2.2.1.10.1.1.18 |
upcContractUseAltCLPThresholdThis flag determines whether the Series-DW per-VC Alternate CLP Threshold should be used for all non-ABR VC's created with this UPC contract.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.10.1.1.19 |
upcContractMCRThe minimum cell rate (cells/sec) for ABR connections.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.10.1.1.20 |
upcContractEstimatedUbrBandwidthThe estimated UBR bandwidth in Kilo-CPS associated with this UPC contractrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.10.1.1.21 |
upcContractAAL5CountingModeThe Counter mode for an AAL5 connectionrw AAL5CountingMode .1.3.6.1.4.1.326.2.2.2.1.10.1.1.22 |
upcContractServiceCategoryIndex of this service category within serviceCategoryTablerw Integer32 .1.3.6.1.4.1.326.2.2.2.1.10.1.1.23 |
upcContractPoliceSchemeIt identifies the policing associated with the UPC contract as defined in the ATM Forum TM 4.0 specifications. However, the policing schemes cbr0 and cbr0tag are specific to FORE switchesrw Enumeration .1.3.6.1.4.1.326.2.2.2.1.10.1.1.24 |
upcContractPCRThe peak cell rate (cells/sec)rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.10.1.1.25 |
upcContractSCRThe sustained cell rate (cells/sec). It also holds the PCR0 value for cbr0 & cbr0tag contractsrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.10.1.1.26 |
upcContractMBSThe maximum burst size (cells)rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.10.1.1.27 |
upcContractServiceSubCategoryThe Service subcategory for this connection.Default value is 1.rw INTEGER .1.3.6.1.4.1.326.2.2.2.1.10.1.1.28 |
upcContractCongestionBasedPeakBwThe expected peak bandwidth for this congestion based UPC contractrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.10.1.1.29 |
upcContractBehaviorClassSelectorThe behavior class selector (BCS) for this UPC contractrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.10.1.1.30 |
confTopologyGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.11 |
confTopoHelloIntervalThis is the time interval in milli seconds between successive Hello Indication messages sent by SPANSrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.11.1 |
confTopoNsapIndIntervalThis is the time interval in milli seconds between successive NSAP Indication messages sent by SPANSrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.11.2 |
confTopoStaticUpdateIntervalThis is the time interval in milli seconds between successive refreshes of NSAP static routes in the NSAP topologyrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.11.3 |
confTopoMaxHopCountThis is the upper limit on the number of hops in the source routes computed by the NSAP routerrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.11.4 |
confTopoACRPropMultThis is the proportional multiplier expressed as a percentage of Available Cell Rate (ACR). If the percentage change of the ACR of any given link in the NSAP topology exceeds this threshold, then the change is deemed significantrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.11.5 |
confTopoMinThreshThis is the capacity value in Cells per second of the minimum value that the threshold value for determining the significant change can take. This minimum value is used to ensure that the threshold for determining significant changes to ACR does not become a very small value in cases where product of the ACR and the proportional multiplier is a very small number.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.11.6 |
confTopoMinVCAvailThis is the minimum number of VCs that should be available on a link before the state of the link changes from VCs-not- available to VCs-available. This state is propagated in the link state information. The state changes from VCs-available to VCs-not-available when the number of VCs available becomes zero from a non-zero value.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.11.7 |
confTopoSpansAreaIDThis is the ID of the Area in the SPANS routing hierarchy to which this switch belongs. This number goes into the most significant byte of the SPANS ATM addressrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.11.8 |
confTopoSpansBorderSwitchThis variable indicates wherher this switch is configured to operate as a SPANS-NNI Border Switch or notrw Enumeration .1.3.6.1.4.1.326.2.2.2.1.11.9 |
confTopoSwitchPrefixThe default NSAP (Network Service Access Point) prefix for this ATM switch. The NSAP prefix will be used in the ILMI address registration message as well as the 'hello-indication' SPANS-NNI message.rw NsapPrefix .1.3.6.1.4.1.326.2.2.2.1.11.10 |
confTopoSwitchPrefixMaskThis mask gives the number of leading bits in the above prefix to be used to aggregate the addresses that belong to the switch in SPANS-PNNI alias FORE-PNNIrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.11.11 |
confTopoPeerGroupMaskThis mask gives the number of the leading bits in the above prefix to be used to aggregate the addresses that belong to the peer group containing this switch in SPANS-PNNI alias FORE-PNNIrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.11.12 |
confTopoSpansPnniBorderSwitchThis variable indicates whether this switch is configured to operate as a SPANS-PNNI Border Switch or notrw Enumeration .1.3.6.1.4.1.326.2.2.2.1.11.13 |
confTopoPGSNReachCostThis is used to indicate cost of link from border node to PGSNrw INTEGER .1.3.6.1.4.1.326.2.2.2.1.11.14 |
confTopoPGSNReachCostMethodThis variable indicates the method of computing cost of link from border node to PGSNrw Enumeration .1.3.6.1.4.1.326.2.2.2.1.11.15 |
confTopoFtPnniForeAreaThis variable is the area ID of the FT-PNNI autonomous system in the global fore hierarchy of PNNI and FT-PNNI peergroupsrwdeprecated Integer32 .1.3.6.1.4.1.326.2.2.2.1.11.16 |
confTopoFtPnniForeLevelThis variable is the level of the FT-PNNI autonomous system in the global fore hierarchy of PNNI and FT-PNNI peergroupsrwdeprecated Integer32 .1.3.6.1.4.1.326.2.2.2.1.11.17 |
confTopoLBUbrLoadBalanceThis variable indicates whether this switch is to do Load Balanced UBR routingrw Enumeration .1.3.6.1.4.1.326.2.2.2.1.11.18 |
oamGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.12 |
oamGeneratingChannelTableWhen an AIS cell is generated on a particular channel it gets added to this table. If a channel is deleted the corresponding entry is removed from this table. SEQUENCE OF OamGeneratingChannelEntry .1.3.6.1.4.1.326.2.2.2.1.12.1 |
oamGeneratingChannelEntryA table entry containing a channel which has generated AIS cells. OamGeneratingChannelEntry .1.3.6.1.4.1.326.2.2.2.1.12.1.1 |
oamGeneratingChannelCellsThe number of AIS OAM cells generated on this channel.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.12.1.1.1 |
oamGeneratingOpathTableWhen an RDI cell is generated on a particular outgoing path it gets added to this table. If an outgoing path is deleted the corresponding entry is removed from this table. SEQUENCE OF OamGeneratingOpathEntry .1.3.6.1.4.1.326.2.2.2.1.12.2 |
oamGeneratingOpathEntryA table entry containing an outgoing path which has generated RDI cells. OamGeneratingOpathEntry .1.3.6.1.4.1.326.2.2.2.1.12.2.1 |
oamGeneratingOpathCellsThe number of RDI OAM cells generated on this path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.12.2.1.1 |
oamGeneratingPathrTableWhen an AIS cell is generated on a particular through path it gets added to this table. If a through path is deleted the corresponding entry is removed from this table. SEQUENCE OF OamGeneratingPathrEntry .1.3.6.1.4.1.326.2.2.2.1.12.3 |
oamGeneratingPathrEntryA table entry containing a through path which has generated AIS cells. OamGeneratingPathrEntry .1.3.6.1.4.1.326.2.2.2.1.12.3.1 |
oamGeneratingPathrCellsThe number of AIS OAM cells generated on this path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.12.3.1.1 |
oamReceivedPathTableWhen an OAM cell is received on a particular terminating path it gets added to this table. If a terminating path is deleted the corresponding entry is removed from this table. SEQUENCE OF OamReceivedPathEntry .1.3.6.1.4.1.326.2.2.2.1.12.4 |
oamReceivedPathEntryA table entry containing a terminating path which has received OAM cells. OamReceivedPathEntry .1.3.6.1.4.1.326.2.2.2.1.12.4.1 |
oamReceivedPathAISCellsThe number of AIS OAM cells received on this path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.12.4.1.1 |
oamReceivedPathRDICellsThe number of RDI OAM cells received on this path.ro Counter32 .1.3.6.1.4.1.326.2.2.2.1.12.4.1.2 |
guardGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.13 |
guardTableThe OAM guards for each board in a switch. SEQUENCE OF GuardEntry .1.3.6.1.4.1.326.2.2.2.1.13.1 |
guardEntryA table entry containing the guards for a board. GuardEntry .1.3.6.1.4.1.326.2.2.2.1.13.1.1 |
oamGuardThe value of sysUpTime the last time an OAM cell was generated/received on this board.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.13.1.1.1 |
ifIndexMapGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.14 |
ifIndexMapTableA table containing information about how physical interfaces ifIndexes relate to the b-n-p triplets. Other ifIndices will not have entries in this table. SEQUENCE OF IfIndexMapEntry .1.3.6.1.4.1.326.2.2.2.1.14.1 |
ifIndexMapEntryA table entry containing ifindex/b-n-p information. IfIndexMapEntry .1.3.6.1.4.1.326.2.2.2.1.14.1.1 |
ifIndexMapIndexThe ifIndex of this entry. The ifindex must be that of a physical interface.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.14.1.1.1 |
ifIndexMapBoardThe board number that this ifIndex refers toro Integer32 .1.3.6.1.4.1.326.2.2.2.1.14.1.1.2 |
ifIndexMapNetmodThe netmod number that this ifIndex refers toro Integer32 .1.3.6.1.4.1.326.2.2.2.1.14.1.1.3 |
ifIndexMapPortThe port number that this ifIndex refers toro Integer32 .1.3.6.1.4.1.326.2.2.2.1.14.1.1.4 |
ifIndexNameGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.15 |
cesExtGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.16 |
cesExtTableThis indicates the value of the next available index to be used for CES creationro TestAndIncr (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.16.1 |
cbrctConfTableA table of CBR Cut-through configuration information. SEQUENCE OF CbrctConfEntry .1.3.6.1.4.1.326.2.2.2.1.16.2 |
cbrctConfEntryA table entry containing CBR Cut-through configuration information for each CES connection. CbrctConfEntry .1.3.6.1.4.1.326.2.2.2.1.16.2.1 |
cbrctStateThis variable indicates whether the CBR Cut-through feature is enabled or disabled on the ingress connection. The values mean: enabled CBR Cut-through enabled disabled CBR Cut-through disabledrw Enumeration .1.3.6.1.4.1.326.2.2.2.1.16.2.1.1 |
cbrctIdleDetectionThis variable identifies the idle detection mechanism used on this connection. The different values are: idlePattern(1) detection is based on idle pattern detection cas(2) detection is based on CAS signallingrw Enumeration .1.3.6.1.4.1.326.2.2.2.1.16.2.1.2 |
cbrctIdleMaskThis contains the mask pattern for idle detection.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.16.2.1.3 |
cbrctNoOfIdlePatternsThis variable contains the number of idle patterns configured for detection.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.16.2.1.4 |
cbrctIdlePatternsThis contains the patterns for idle detection. For detection based on both idle and mask patterns it contains the idle octet patterns. For detection based on signalling it contains the octet value of AB signalling bits (eg. 00000010 (02H), the bit 0 is B bit and bit 1 is A bit). Maximum of 4 idle patterns are used. The idle patterns get filled from the least significant byte. The cbrctNoOfIdlePatterns gives the number of idle patterns.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.16.2.1.5 |
cbrctIdleIntPeriodThis contains the integration period for idle detection.rw TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.16.2.1.6 |
cbrctActiveIntPeriodThis contains the integration period for active detection.rw TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.16.2.1.7 |
qosClassExpansionGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.17 |
qosClassExpansionTableA table of user defined QOS Class Expansions. SEQUENCE OF QosClassExpansionEntry .1.3.6.1.4.1.326.2.2.2.1.17.1 |
qosClassExpansionEntryA table entry containing a user defined QOS Class Expansion. QosClassExpansionEntry .1.3.6.1.4.1.326.2.2.2.1.17.1.1 |
qosClassExpansionKeyThe unique key for the set of entries in this table that make up a QOS Class Mapping table. Only one entry for each Class is allowed per key. Integer32 .1.3.6.1.4.1.326.2.2.2.1.17.1.1.1 |
qosClassValueQOS Class which needs to be expanded. If a class does not exist for a specific Expansion Key, all qos parameters will be interpreted as any acceptable qos parameter value. Enumeration .1.3.6.1.4.1.326.2.2.2.1.17.1.1.2 |
qosClassExpansionEntryStatusThe SNMP status of this Expansion entry.rw EntryStatus .1.3.6.1.4.1.326.2.2.2.1.17.1.1.3 |
qosClassFwdCtdThe maximum acceptable forward Cell Transfer Delay in microseconds to be used for this expansion. A value of 16777215 will signify any acceptable forward CTD value.rw INTEGER .1.3.6.1.4.1.326.2.2.2.1.17.1.1.4 |
qosClassFwdCdvThe maximum acceptable peak to peak forward Cell Delay Variation in micro-seconds to be used for this expansion. A value of 16777215 will signify any acceptable forward CDV value.rw INTEGER .1.3.6.1.4.1.326.2.2.2.1.17.1.1.5 |
qosClassBackCdvThe maximum acceptable peak to peak backward Cell Delay Variation in micro-seconds to be used for this expansion. A value of 16777215 will signify any acceptable backward CDV value.rw INTEGER .1.3.6.1.4.1.326.2.2.2.1.17.1.1.6 |
qosClassFwdClr10 raised to the power of this value signifies the maximum acceptable forward Cell Loss Ratio value to be used for this expansion. The valid values are from 1 to 15 (both inclusive) and 255. A value of 255 will signify any acceptable forward CLR value.rw INTEGER .1.3.6.1.4.1.326.2.2.2.1.17.1.1.7 |
qosClassBackClr10 raised to the power of this value signifies the maximum acceptable backward Cell Loss Ratio value to be used for this expansion. The valid values are from 1 to 15 (both inclusive) and 255. A value of 255 will signify any acceptable backward CLR value.rw INTEGER .1.3.6.1.4.1.326.2.2.2.1.17.1.1.8 |
qosClassNameA name associated with this entry in the qos class tablerw DisplayString .1.3.6.1.4.1.326.2.2.2.1.17.1.1.9 |
pathExtGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.18 |
pathExtQosMetricTableQos metric table for path extension SEQUENCE OF PathExtQosMetricEntry .1.3.6.1.4.1.326.2.2.2.1.18.1 |
pathExtQosMetricEntry PathExtQosMetricEntry .1.3.6.1.4.1.326.2.2.2.1.18.1.1 |
pathExtQosMetricIndex Integer32 .1.3.6.1.4.1.326.2.2.2.1.18.1.1.1 |
pathExtQosMetricMaxCtdcell transfer delay in microsecondsrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.18.1.1.2 |
pathExtQosMetricMaxCdvcell delay variation in microsecondsrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.18.1.1.3 |
pathExtQosMetricMaxClrcell loss ratio. 10**(-n) where n is the returned valuerw Integer32 .1.3.6.1.4.1.326.2.2.2.1.18.1.1.4 |
pathExtQosMetricEntryStatusrw EntryStatus .1.3.6.1.4.1.326.2.2.2.1.18.1.1.5 |
pathExtTablepath extension table SEQUENCE OF PathExtEntry .1.3.6.1.4.1.326.2.2.2.1.18.2 |
pathExtEntryA table entry containing path Qos Metric information. PathExtEntry .1.3.6.1.4.1.326.2.2.2.1.18.2.1 |
pathExtCbrMetricindex to the path ext qos metric tablerw Integer32 .1.3.6.1.4.1.326.2.2.2.1.18.2.1.1 |
pathExtRtVbrMetricindex to the path ext qos metric tablerw Integer32 .1.3.6.1.4.1.326.2.2.2.1.18.2.1.2 |
pathExtNrtVbrMetricindex to the path ext qos metric tablerw Integer32 .1.3.6.1.4.1.326.2.2.2.1.18.2.1.3 |
pathExtAbrMetricindex to the path ext qos metric tablerw Integer32 .1.3.6.1.4.1.326.2.2.2.1.18.2.1.4 |
pathExtUbrMetricindex to the path ext qos metric tablerw Integer32 .1.3.6.1.4.1.326.2.2.2.1.18.2.1.5 |
pathExtEntryStatusrw EntryStatus .1.3.6.1.4.1.326.2.2.2.1.18.2.1.6 |
outputPathExtTable SEQUENCE OF OutputPathExtEntry .1.3.6.1.4.1.326.2.2.2.1.18.3 |
outputPathExtEntry OutputPathExtEntry .1.3.6.1.4.1.326.2.2.2.1.18.3.1 |
opathExtCbrMetricindex to the path ext qos metric tablerw Integer32 .1.3.6.1.4.1.326.2.2.2.1.18.3.1.1 |
opathExtRtVbrMetricindex to the path ext qos metric tablerw Integer32 .1.3.6.1.4.1.326.2.2.2.1.18.3.1.2 |
opathExtNrtVbrMetricindex to the path ext qos metric tablerw Integer32 .1.3.6.1.4.1.326.2.2.2.1.18.3.1.3 |
opathExtAbrMetricindex to the path ext qos metric tablerw Integer32 .1.3.6.1.4.1.326.2.2.2.1.18.3.1.4 |
opathExtUbrMetricindex to the path ext qos metric tablerw Integer32 .1.3.6.1.4.1.326.2.2.2.1.18.3.1.5 |
opathExtEntryStatusrw EntryStatus .1.3.6.1.4.1.326.2.2.2.1.18.3.1.6 |
vpGroupTable SEQUENCE OF VpGroupEntry .1.3.6.1.4.1.326.2.2.2.1.18.4 |
vpGroupEntry VpGroupEntry .1.3.6.1.4.1.326.2.2.2.1.18.4.1 |
vpGroupIndexZero mean not belong to any vpgroup groupro Integer32 .1.3.6.1.4.1.326.2.2.2.1.18.4.1.1 |
vpGroupPortro Integer32 .1.3.6.1.4.1.326.2.2.2.1.18.4.1.2 |
vpGroupVPIro Integer32 .1.3.6.1.4.1.326.2.2.2.1.18.4.1.3 |
vpGroupVPCIrw Integer32 .1.3.6.1.4.1.326.2.2.2.1.18.4.1.4 |
vpGroupEntryStatusrw EntryStatus .1.3.6.1.4.1.326.2.2.2.1.18.4.1.5 |
poolGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.19 |
poolConfGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.19.1 |
poolConfPPCallsSpecifies the number of point to point calls that the switch should handle through pools. The switch comes up with enough resources in the pools to handle so many point to point calls. The new value will take effect at the next reboot.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.19.1.1 |
poolConfPMPCallsSpecifies the number of point to multipoint calls that the switch should handle through pools. The switch comes up with enough resources in the pools to handle so many point to multipoint calls. The new value will take effect at the next reboot.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.19.1.2 |
poolConfMaxPercentageLimits the max percentage of the main heap that can be taken for pool configuration purposes.rw Integer32 .1.3.6.1.4.1.326.2.2.2.1.19.1.5 |
asxAtmIfGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.20 |
asxAtmIfTableA table of atm interface information. SEQUENCE OF AsxAtmIfEntry .1.3.6.1.4.1.326.2.2.2.1.20.1 |
asxAtmIfEntryA table entry containing atm interface information. AsxAtmIfEntry .1.3.6.1.4.1.326.2.2.2.1.20.1.1 |
asxAtmIfNameThe persistent name of this atm interface. It is used to index this atm interface. All letters in the asxAtmIfName are always represented in uppercase. DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.20.1.1.1 |
asxAtmIfLinkidThe linkid of this atm interface.ro Integer32 .1.3.6.1.4.1.326.2.2.2.1.20.1.1.2 |
syncStatusMsgGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.21 |
syslogGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.1.22 |
syslogFacilityThe syslog facility string, possible values are daemon, local[0-7].rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.22.1 |
syslogConsoleStateThe syslog console state, ON means syslog messages are sent to console.rw Enumeration .1.3.6.1.4.1.326.2.2.2.1.22.2 |
syslogDestinationTableThis table lists all the syslog destinations SEQUENCE OF SyslogDestinationEntry .1.3.6.1.4.1.326.2.2.2.1.22.3 |
syslogDestinationEntryA structure containing the parameters for a syslog destination SyslogDestinationEntry .1.3.6.1.4.1.326.2.2.2.1.22.3.1 |
syslogDestinationHostThe host IP address of the syslog destination IpAddress .1.3.6.1.4.1.326.2.2.2.1.22.3.1.1 |
syslogDestinationStatusAdministrative status of this entryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.326.2.2.2.1.22.3.1.2 |
snmp OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.2 |
trapConfGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.2.1 |
trapNumberOfDestThe current number of configured trap destinations. All traps are sent to all destinations.rodeprecated Integer32 .1.3.6.1.4.1.326.2.2.2.2.1.1 |
trapDestTableA table of destinations to which the agent sends traps.deprecated SEQUENCE OF TrapDestEntry .1.3.6.1.4.1.326.2.2.2.2.1.2 |
trapDestEntryA table entry containing address of a management station, to which the agent sends traps.deprecated TrapDestEntry .1.3.6.1.4.1.326.2.2.2.2.1.2.1 |
trapDestAddress to which the agent sends traps. Usually a network management station sets this address to itself.rodeprecated IpAddress .1.3.6.1.4.1.326.2.2.2.2.1.2.1.1 |
trapDestStatusThe status of this trap destination entry.rwdeprecated EntryStatus .1.3.6.1.4.1.326.2.2.2.2.1.2.1.2 |
snmpConfGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.2.2 |
snmpReconfigureThe SNMP agent will reset itself and reconfigure its database from the default database when this variable is set to enable(2). After reconfiguring is done, the value of this object is disable(1). Note that enabling snmpReconfigure will end up with a loss of the entire ATM configuration.rwdeprecated Enumeration .1.3.6.1.4.1.326.2.2.2.2.2.1 |
snmpReadCommunityThe community string used for SNMP (v1) read operations, i.e. get and getnext requests. This has been deprecated, since it's now possible to have more than one read community string. Setting this variable will result in all current read community strings being deleted, and this one added. Note this object is write-only and reading it will result in implementation-specific results.rwdeprecated OCTET STRING .1.3.6.1.4.1.326.2.2.2.2.2.2 |
snmpWriteCommunityThe community string used for SNMP (v1) write operations, i.e. set requests. This has been deprecated, since it's now possible to have more than one write community string. Setting this variable will result in all current write community strings being deleted, and this one added. Note this object is write-only and reading it will result in implementation-specific results.rwdeprecated OCTET STRING .1.3.6.1.4.1.326.2.2.2.2.2.3 |
snmpWarmStartThe SNMP agent will reset the switch, and restart the switch control software using the existing configuration database when this variable is set to enable(2). After the warm start, the value of this object is disable(1). A warmStart trap is sent after the switch control software restarts.rw Enumeration .1.3.6.1.4.1.326.2.2.2.2.2.4 |
snmpColdStartThe SNMP agent will reset the configuration database for all ATM related configuration objects, and reboot the switch, when this variable is set to enableResetAtmConf(2). When the value of this variable is set to enableResetAllConf(3), all configuration objects, including ATM and IP objects will be removed, and the switch will be rebooted. A coldStart trap is sent just before the trap destination table is removed. After the cold start, the value of this object is disable(1).rw Enumeration .1.3.6.1.4.1.326.2.2.2.2.2.5 |
snmpRemoteSetsStatusThe value of this object controls SNMP set operations from remote management stations. The default value is enabled(1). If it is set to disabled(2), set requests from remote management stations will not be processed and an authorization error is returned. This value can be set only by the manager running on this device.rodeprecated Enumeration .1.3.6.1.4.1.326.2.2.2.2.2.6 |
snmpAgentAddressGroup OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.2.2.2.5 |
snmpThisAgentBoardNumberThe instance of this agent type within the enclosure; typically a board number.ro INTEGER .1.3.6.1.4.1.326.2.2.2.2.5.1 |
snmpAgentTableA table of SNMP agent IP addresses. Each entry in this table represents an IP address which may be used to reach the associated SNMP agent, assuming appropriate network connectivity. SEQUENCE OF SnmpAgentEntry .1.3.6.1.4.1.326.2.2.2.2.5.2 |
snmpAgentEntryA table entry containing the identity and address of an SNMP agent. SnmpAgentEntry .1.3.6.1.4.1.326.2.2.2.2.5.2.1 |
snmpAgentBoardNumberThe number of the SNMP agent within this enclosure. This generally corresponds to a board number.ro Integer32 .1.3.6.1.4.1.326.2.2.2.2.5.2.1.1 |
snmpAgentInterfaceAn interface number associated with the agent IP address. This number is for tabulation purposes only, and has no other significance.ro Integer32 .1.3.6.1.4.1.326.2.2.2.2.5.2.1.2 |
snmpAgentAddressThe IP address of the identified SNMP agent.ro IpAddress .1.3.6.1.4.1.326.2.2.2.2.5.2.1.3 |
foreSwitchModuleFore Switch MIB MODULE-IDENTITY .1.3.6.1.4.1.326.2.7 |