POWERHUB-CORE-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
217
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
217 total| Object Name |
|---|
fore OBJECT IDENTIFIER .1.3.6.1.4.1.326 |
systems OBJECT IDENTIFIER .1.3.6.1.4.1.326.2 |
lsd OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.6 |
lsdproducts OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.6.1 |
powerhub4k6k7k OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.6.1.1 |
alchassis OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.6.1.1.1 |
powerFailureThe powerFailure trap indicates that powerFailure
occured in the particular powersupply unit. TRAP-TYPE .1.3.6.1.4.1.326.2.6.1.1.1.0.1 |
boardFailureThe boardFailure trap indicates that intelligent card
failure occured in the particular slot. TRAP-TYPE .1.3.6.1.4.1.326.2.6.1.1.1.0.2 |
alSlotTableA table that contains information about
each slot in the PowerHub 4k6k7k chassis. SEQUENCE OF AlSlotEntry .1.3.6.1.4.1.326.2.6.1.1.1.1 |
alSlotEntryInformation about a specific slot. AlSlotEntry .1.3.6.1.4.1.326.2.6.1.1.1.1.1 |
alSlotNumberThe slot number for which the following
information applies.ro INTEGER .1.3.6.1.4.1.326.2.6.1.1.1.1.1.1 |
alSlotCardTypeThe card type for this slot.ro Enumeration .1.3.6.1.4.1.326.2.6.1.1.1.1.1.2 |
alSlotStatusThe status of the card in this slot.ro Enumeration .1.3.6.1.4.1.326.2.6.1.1.1.1.1.3 |
alSlotModelThe model number for this card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.1.1.1.1.1.4 |
alSlotRevisionThe revision number for this card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.1.1.1.1.1.5 |
alSlotIssueThe issue number for this slot.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.1.1.1.1.1.6 |
alSlotDeviationThe deviation for this slot.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.1.1.1.1.1.7 |
alSlotSerialNumberThe serial number of this card this slot.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.1.1.1.1.1.8 |
alSlotPower5The number of milliamps. of current drawn
by this slot at 5 Volts.ro INTEGER .1.3.6.1.4.1.326.2.6.1.1.1.1.1.9 |
alSlotPower12The number of milliamps. of current drawn
by this slot at 12 Volts.ro INTEGER .1.3.6.1.4.1.326.2.6.1.1.1.1.1.10 |
alSlotPower33The number of milliamps. of current drawn
by this slot at 3.3 Volts.ro INTEGER .1.3.6.1.4.1.326.2.6.1.1.1.1.1.11 |
alSlotPowerOtherThe number of milliamps. of current drawn
by this slot at OTHER voltage.ro INTEGER .1.3.6.1.4.1.326.2.6.1.1.1.1.1.12 |
alVportTableA table that contains information about
each virtual port in the PowerHub 4k6k7k
chassis. This table differs from the alSlotToVportTable
mainly in how this table is indexed. SEQUENCE OF AlVportEntry .1.3.6.1.4.1.326.2.6.1.1.1.2 |
alVportEntryInformation about a specific virtual port. AlVportEntry .1.3.6.1.4.1.326.2.6.1.1.1.2.1 |
alVportNumberThe virtual port number for which the
following information applies.ro INTEGER .1.3.6.1.4.1.326.2.6.1.1.1.2.1.1 |
alVportSlotNumberThe slot number which holds the physical port that
corresponds to the virtual port of interest.ro INTEGER .1.3.6.1.4.1.326.2.6.1.1.1.2.1.2 |
alVportPortNumberThe physical port number on the slot that corresponds
to
this virtual port number, identified by alVportNumber.ro INTEGER .1.3.6.1.4.1.326.2.6.1.1.1.2.1.3 |
alVportPortTypeThe port type for this virtual port.ro Enumeration .1.3.6.1.4.1.326.2.6.1.1.1.2.1.4 |
alVportStatusThe port status for this virtual port.ro Enumeration .1.3.6.1.4.1.326.2.6.1.1.1.2.1.5 |
alVportControllerTypeThe controller type for this virtual port.ro INTEGER .1.3.6.1.4.1.326.2.6.1.1.1.2.1.6 |
alVportDataRateConfigThe data rate requested for this virtual port.rw Enumeration .1.3.6.1.4.1.326.2.6.1.1.1.2.1.7 |
alVportOperModeConfigThe operating mode requested for this virtual port.rw Enumeration .1.3.6.1.4.1.326.2.6.1.1.1.2.1.8 |
alVportAutoNegotiateConfigThe auto-negotiation requested for this virtual port.rw Enumeration .1.3.6.1.4.1.326.2.6.1.1.1.2.1.9 |
alVportDataRateStatusThe actual data rate for this virtual port.ro Enumeration .1.3.6.1.4.1.326.2.6.1.1.1.2.1.10 |
alVportOperModeStatusThe actual operating mode for this virtual port.ro Enumeration .1.3.6.1.4.1.326.2.6.1.1.1.2.1.11 |
alSlotToVportTableA table that contains information about
each port of each slot in the PowerHub 4k6k7k
chassis. This table is established as a way to
specify the information about a physical port located
on a slot in the PowerHub 4k6k7k chassis. This table
a slot and port number scheme. This table differs from
uses two indices (the slot number and the port number)
to identify a port. SEQUENCE OF AlSlotVportEntry .1.3.6.1.4.1.326.2.6.1.1.1.3 |
alSlotVportEntryInformation about a specific port in a specific slot.
The slot number and the port number in that slot
(numbered left to right in ascending order) identifies
a specific port. AlSlotVportEntry .1.3.6.1.4.1.326.2.6.1.1.1.3.1 |
alSlotVportSlotNumberThe slot number which holds the port of interest.ro INTEGER .1.3.6.1.4.1.326.2.6.1.1.1.3.1.1 |
alSlotVportPortNumberThe physical port number on a slot which represents
the port of interest. The physical port is numbered
from left to right in a slot.ro INTEGER .1.3.6.1.4.1.326.2.6.1.1.1.3.1.2 |
alSlotVportNumberThe virtual port number which corresponds to the port
that is identified by the slot and port number. This
scheme thereby relates each virtual port to a slot and
physical port tuplet.ro INTEGER .1.3.6.1.4.1.326.2.6.1.1.1.3.1.3 |
alSlotVportPortTypeThe port type for this port.ro Enumeration .1.3.6.1.4.1.326.2.6.1.1.1.3.1.4 |
alSlotVportStatusThe status for this port.ro INTEGER .1.3.6.1.4.1.326.2.6.1.1.1.3.1.5 |
alSlotVportControllerTypeThe controller type for this port.ro INTEGER .1.3.6.1.4.1.326.2.6.1.1.1.3.1.6 |
alSlotVportDataRateConfigThe data rate requested for this port. The actual data
rate
may be different from the requested data rate.rw Enumeration .1.3.6.1.4.1.326.2.6.1.1.1.3.1.7 |
alSlotVportOperModeConfigThe operating mode requested for this port.rw Enumeration .1.3.6.1.4.1.326.2.6.1.1.1.3.1.8 |
alSlotVportAutoNegotiateConfigThe auto-negotiation requested for this port.rw Enumeration .1.3.6.1.4.1.326.2.6.1.1.1.3.1.9 |
alSlotVportDataRateStatusThe actual data rate for this port.ro Enumeration .1.3.6.1.4.1.326.2.6.1.1.1.3.1.10 |
alSlotVportOperModeStatusThe actual operating mode for this port.ro Enumeration .1.3.6.1.4.1.326.2.6.1.1.1.3.1.11 |
alPSTableA table that contains information about
each power supply in the PowerHub 4k6k7k
chassis. SEQUENCE OF AlPSEntry .1.3.6.1.4.1.326.2.6.1.1.1.4 |
alPSEntryInformation about a specific power supply. AlPSEntry .1.3.6.1.4.1.326.2.6.1.1.1.4.1 |
alPSNumberThe power supply numberro INTEGER .1.3.6.1.4.1.326.2.6.1.1.1.4.1.1 |
alPSStatusThe status of the power supply identified by the
instance of alPSNumber.ro Enumeration .1.3.6.1.4.1.326.2.6.1.1.1.4.1.2 |
alCpuSlotThe slot number in which the packet engine
residesro INTEGER .1.3.6.1.4.1.326.2.6.1.1.1.5 |
alSlotChassisThe maximum number of slots available in the
powerhub. Presently it could either be a 5,
10, or 15 slot chassis. This object is used
only for PH7000.ro Enumeration .1.3.6.1.4.1.326.2.6.1.1.1.6 |
powerbits OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.6.1.2 |
asn9000 OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.6.1.3 |
lsdcommon OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.6.2 |
alsystem OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.6.2.1 |
alLoginFailureThe login failure trap indicates that the login
failed due to some error condition during the
login process. TRAP-TYPE .1.3.6.1.4.1.326.2.6.2.1.0.1 |
alChassisTypeThe model type of the PowerHubro Enumeration .1.3.6.1.4.1.326.2.6.2.1.1 |
alMcpuRtVerRuntime software version of the motherboard CPU;
it is an ASCII string that describes the version
as well as the date and time the software was
released from the factory.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.2.1.2 |
alMcpuPromVerPROM software version of the motherboard CPU;
it is an ASCII string that describes the version
as well as the date and time the software was
released from the factory.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.2.1.3 |
alFcpuOneRtVerRuntime software version of F-bus CPU for the first
FDDI board.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.2.1.4 |
alFcpuTwoRtVerRuntime software version of F-bus CPU for the second
FDDI board.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.2.1.5 |
alFcpuOnePromVerPROM software version of F-bus CPU for the first
FDDI board.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.2.1.6 |
alFcpuTwoPromVerPROM software version of F-bus CPU for the second
FDDI board.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.2.1.7 |
alRcpuOneRtVerRuntime software version of Ring CPU for the first
FDDI board.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.2.1.8 |
alRcpuTwoRtVerRuntime software version of Ring CPU for the second
FDDI board.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.2.1.9 |
alRcpuOnePromVerPROM software version of Ring CPU for the first
FDDI board.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.2.1.10 |
alRcpuTwoPromVerPROM software version of Ring CPU for the second
FDDI board.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.2.1.11 |
alLastLoginFailureTimeDateTime and date string of the last login session
that failed.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.2.1.12 |
alLastLoginFailureUserIdUser id of the last login session that failed.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.2.1.13 |
alLastLoginFailureReasonReason code for the last login failure.ro Enumeration .1.3.6.1.4.1.326.2.6.2.1.14 |
alLastLoginSourceAddressSource address of the last login session that failed.
The value would be either 'console' or ipaddress string
of the telnet session.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.2.1.15 |
alConsoleSyslogLevelLevel which generates a logging messsage for console
port commands (telnet, tip, etc.); no messages if set
to off(1).rw Enumeration .1.3.6.1.4.1.326.2.6.2.1.17 |
alSnmpSyslogLevelLevel which generates a logging messsage for snmp
induced changes; no messages if set to off(1).rw Enumeration .1.3.6.1.4.1.326.2.6.2.1.18 |
alIlmiSyslogLevelLevel which generates a logging messsage for ilmi
configuration changes; no messages if set to off(1).rw Enumeration .1.3.6.1.4.1.326.2.6.2.1.19 |
alSyslogHostTypeHost which receives syslog messages:
notSet(1) if no host is set or becomes unset;
local(2) if messages go to console;
ip(3) if messages go to a remote hostrw Enumeration .1.3.6.1.4.1.326.2.6.2.1.20 |
alSyslogHostIpIP address of remote host which receives syslog
messages; must be set if alSyslogHost is set to ip.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.2.1.21 |
alSyslogHostIpFacilitySyslog facility to be assigned to all syslog
messages. Default is daemon(1).rw Enumeration .1.3.6.1.4.1.326.2.6.2.1.22 |
albridge OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.6.2.2 |
alBridgeTableA table that contains information about
unicast entries for which the bridge has forwarding
and/or filtering information. This information
is used by the transparent bridging function in
determining how to propagate a received frame. SEQUENCE OF AlBridgeEntry .1.3.6.1.4.1.326.2.6.2.2.1 |
alBridgeEntryInformation about a specific unicast MAC
address for which the bridge has some forwarding
and/or filtering information. AlBridgeEntry .1.3.6.1.4.1.326.2.6.2.2.1.1 |
alBridgeEntryAddressThe MAC address for which the bridge
has forwarding and/or filtering information.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.2.2.1.1.1 |
alBridgeEntryPortThe port number of the port on which a
frame having a source address equal to the
value of the corresponding instance of
alBridgeEntryAddress has been seen.ro INTEGER .1.3.6.1.4.1.326.2.6.2.2.1.1.2 |
alBridgeEntryLinkThe link number on the port on which
a frame having as ource address equal to the
value of the corresponding instance of
alBridgeEntryAddress has been seen. Only applies
to the UTP port type.ro INTEGER .1.3.6.1.4.1.326.2.6.2.2.1.1.3 |
alBridgeEntryRuleThe rule number that is applied to
packets that are forwarded to or from this
address.ro INTEGER .1.3.6.1.4.1.326.2.6.2.2.1.1.4 |
alBridgeEntryFlagsThe status of this entry.ro INTEGER .1.3.6.1.4.1.326.2.6.2.2.1.1.5 |
alBridgeTblClearWhen set, clears the Bridge table.rw INTEGER .1.3.6.1.4.1.326.2.6.2.2.2 |
alBrFlushCacheWhen set, flushes the cache.rw INTEGER .1.3.6.1.4.1.326.2.6.2.2.3 |
alPortStatsTablePer port statistics SEQUENCE OF PortStatsEntry .1.3.6.1.4.1.326.2.6.2.2.4 |
portStatsEntryPer port statistics entries. PortStatsEntry .1.3.6.1.4.1.326.2.6.2.2.4.1 |
portStatsPortSegment for which the statistics collected.ro INTEGER .1.3.6.1.4.1.326.2.6.2.2.4.1.1 |
portStatsPktsInGood packets received on the segment. Packets are
listed regardless of packet type, or whether the
packet is forwarded to another segment. Error
packets are not listed.ro Counter .1.3.6.1.4.1.326.2.6.2.2.4.1.2 |
portStatsPktsOutPackets transmitted on the segment. This statistic
is incremented when a packet is scheduled for
transmission, not when it is actually transmitted.ro Counter .1.3.6.1.4.1.326.2.6.2.2.4.1.3 |
portStatsOctetsInGood octets received on the segment. This statistic
includes 8 octets per packet to account for the
preamble.ro Counter .1.3.6.1.4.1.326.2.6.2.2.4.1.4 |
portStatsOctetsOutOctets transmitted from the segment. This statistic
is incremented when a packet is scheduled for
transmission, not when it is actually transmitted.
This statistic includes 8 octets per packet to
account for the preamble.ro Counter .1.3.6.1.4.1.326.2.6.2.2.4.1.5 |
portStatsMulticastPktsInBroadcast multicast packets received on the segment.
This statistic is incremented for each good broadcast
or multicast packet received on the segment.ro Counter .1.3.6.1.4.1.326.2.6.2.2.4.1.6 |
portStatsMulticastPktsOutBroadcast multicast packets transmitted from the
segment. This statistic is incremented once for
each broadcast or multicast packet scheduled for
transmission on the segment.ro Counter .1.3.6.1.4.1.326.2.6.2.2.4.1.7 |
portStatsTableMissesPackets received that have unknown destination
addresses. When address learning is enabled, this
statistic is usually incremented only for the first
packet transmitted to a workstation or other device
connected to the segment. After a reply is
received, the device's source address is added
to the bridging table.ro Counter .1.3.6.1.4.1.326.2.6.2.2.4.1.8 |
portStatsRcvBuffErrsIncremented each time the hub detects an incoming
packet but does not have a buffer in which to store
the packet.ro Counter .1.3.6.1.4.1.326.2.6.2.2.4.1.9 |
portStatsXmitBuffErrsIncremented each time the hub attempts to forward
a packet to a busy destination segment whose output
buffers all are full.ro Counter .1.3.6.1.4.1.326.2.6.2.2.4.1.10 |
portStatsTotalCollisionsThe total number of collisions detected on the
segment while attempting to transmit and receive
packets. For FDDI segments, this statistic is
always 0.ro Counter .1.3.6.1.4.1.326.2.6.2.2.4.1.11 |
portStatsRcvCollisionsThe number of collisions detected on the segment
while listening for incoming packets. This statistic
is only available for UTP segments. For segments on
other module types, this statistic is always 0.ro Counter .1.3.6.1.4.1.326.2.6.2.2.4.1.12 |
portStatsXmitCollisionsThe number of collisions detected on the segment
while attempting to transmit packets. For FDDI
segments, this statistic is always 0.ro Counter .1.3.6.1.4.1.326.2.6.2.2.4.1.13 |
portStatsXmitQLenThe number of outgoing packets in the transmit queue.
These packets have been scheduled for transmission,
but have not been transmitted yet.ro Counter .1.3.6.1.4.1.326.2.6.2.2.4.1.14 |
portStatsPeakUtilizationThe segment's maximum utilization during a one-second
interval since the statistics last were cleared.
For Ethernet segments, the current utilization is
calculated as follows:
Once per second, the current one- second
utilization is computed as (total # octets) x
(8 bits/octets) / 10 Mb/s.
The peak utilization is then set to the maximum of
the current one-second utilization and the previous
peak utilization.
NOTE: Total # octets is all octets transmitted and
received on the segment during the previous
second, including 8 octets of preamble per
packet. The Ethernet rate is 10Mb.ro Counter .1.3.6.1.4.1.326.2.6.2.2.4.1.15 |
portStatsCurrUtilizationFor Ethernet segments, the current utilization is
calculated as follows:
Once per second, the current one-second utilization
is computed as (total # octets) x (8 bits/octets) /
10 Mb/s.
NOTE: Total # octets is all octets transmitted and
received on the segment during the previous
second, including 8 octets of preamble per
packet. The Ethernet rate is 10Mb.ro Counter .1.3.6.1.4.1.326.2.6.2.2.4.1.16 |
portStatsLossOfCarrierIndicates that an AUI segment has no cable attached,
or the cable or transceiver is faulty.ro Counter .1.3.6.1.4.1.326.2.6.2.2.4.1.17 |
portStatsExcessRetriesIncremented whenever all of 15 attempts to transmit
a single packet cause collisions. This can happen in
very busy networks, or when no cable is attached to
an enabled BNC port.ro Counter .1.3.6.1.4.1.326.2.6.2.2.4.1.18 |
alBridgeStatsClearWhen set, clears the statistics for the
bridge. When not set, value 0 is returned.rw INTEGER .1.3.6.1.4.1.326.2.6.2.2.5 |
alBridgePPControlWhen set to 3 , disables the port to port
collection of the stats; when set to 1,
enables the port to port stats collection;
when set to 2, clears the port to port
stats.rw Enumeration .1.3.6.1.4.1.326.2.6.2.2.6 |
alPortToPortTableStatistics for port to port traffic. SEQUENCE OF PortToPortEntry .1.3.6.1.4.1.326.2.6.2.2.7 |
portToPortEntryStatistics for port to port traffic PortToPortEntry .1.3.6.1.4.1.326.2.6.2.2.7.1 |
alPPSourcePortSource port numberro INTEGER .1.3.6.1.4.1.326.2.6.2.2.7.1.1 |
alPPDestinationPortDestination port numberro INTEGER .1.3.6.1.4.1.326.2.6.2.2.7.1.2 |
portToPortPacketsPort to port packets.ro INTEGER .1.3.6.1.4.1.326.2.6.2.2.7.1.3 |
portToPortOctetsPort to port octets.ro INTEGER .1.3.6.1.4.1.326.2.6.2.2.7.1.4 |
alPortConfigTablePer port configuration for configuring
Source and Destination Rules etc. SEQUENCE OF PortConfigEntry .1.3.6.1.4.1.326.2.6.2.2.8 |
portConfigEntryPer port configuration. PortConfigEntry .1.3.6.1.4.1.326.2.6.2.2.8.1 |
portConfigPortThe port number for this table entryro INTEGER .1.3.6.1.4.1.326.2.6.2.2.8.1.1 |
portConfigSrcRuleSource Rule for the port number identified
by the instance of portConfigPortrw INTEGER .1.3.6.1.4.1.326.2.6.2.2.8.1.2 |
portConfigDstRuleDestination Rule for the port number
identified by the instance of portConfigPortrw INTEGER .1.3.6.1.4.1.326.2.6.2.2.8.1.3 |
portConfigBlockLearnedEntriesWhen set to True (1), the port identified
by the instance of portConfigPort will block the
learned entries; if set to False (2) the port will
not block the learned entriesrw Enumeration .1.3.6.1.4.1.326.2.6.2.2.8.1.4 |
alBridgeIpBridgingWhen set to enable(1), enables the IP
bridging and if set to disable(2), disables the
IP bridging.rw Enumeration .1.3.6.1.4.1.326.2.6.2.2.9 |
alBrTemplateTablePer template information SEQUENCE OF BrTemplateEntry .1.3.6.1.4.1.326.2.6.2.2.10 |
brTemplateEntryTemplate entry. BrTemplateEntry .1.3.6.1.4.1.326.2.6.2.2.10.1 |
brTemplateNumberThe number of the template with which it
is identified.ro INTEGER .1.3.6.1.4.1.326.2.6.2.2.10.1.1 |
brTemplateOffsetA displacement, in octets, from the
beginning of the packet. This must be a multiple of
4 in the range from 0 to 124 decimal. A value of -1
will delete the entryrw INTEGER .1.3.6.1.4.1.326.2.6.2.2.10.1.2 |
brTemplateMaskA 4-byte (32-bit) number, normally specified as
eight hexadecimal digits (00000000 - ffffffff)
Description: The bytes in the mask are numbered from
0 to 3, starting with the high-order byte
(big-endian format). Each byte of the mask is
ANDed with the octet in the packet at displacement
'offset + i' to form a 4-byte 'masked value'.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.2.2.10.1.3 |
brTemplateComparatorA 4-byte number, usually specified as eight
hexadecimal digits (00000000 - ffffffff)
Description: If the masked value defined above equals
the comparator, then the template returns a value of
'true'; otherwise, it returns a value of 'false'.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.2.2.10.1.4 |
brTemplateOptionSetting this value to 0 assume all 32 bits mask
and comparator specified; value 1 assume half-word
(2 bytes) qunatity; and value 2 assume single-byte
quantity.rw INTEGER .1.3.6.1.4.1.326.2.6.2.2.10.1.5 |
alBrRuleTablePer rule information SEQUENCE OF BrRuleEntry .1.3.6.1.4.1.326.2.6.2.2.11 |
brRuleEntryRule entry. BrRuleEntry .1.3.6.1.4.1.326.2.6.2.2.11.1 |
brRuleNumberA rule number in the range 101-162.
You can define up to 62 rules.ro INTEGER .1.3.6.1.4.1.326.2.6.2.2.11.1.1 |
brRuleStatementSpecifies the templates and the logical operators
that make up the rule. Rule statements consist of
rule numbers joined by the following logical operators:
Operator Means...
& AND
| OR
~ NOT
Rule statements are interpreted from left to right.
Use parentheses to group expressions. You can use
up to eight sets of parentheses to group template
numbers and logical operators.
The total maximum number of characters, including
blanks, is 64.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.2.2.11.1.2 |
alBrRuleToNodeTableRules to specific node. SEQUENCE OF AlBrRuleToNodeEntry .1.3.6.1.4.1.326.2.6.2.2.12 |
alBrRuleToNodeEntryRule node entry. AlBrRuleToNodeEntry .1.3.6.1.4.1.326.2.6.2.2.12.1 |
brRuleToNodePortThe number of the port for which this
rule appliesrw INTEGER .1.3.6.1.4.1.326.2.6.2.2.12.1.1 |
brRuleToNodeMacAddrThe source MAC addressrw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.2.2.12.1.2 |
brRuleToNodeRuleThe rule number that applies to this
entry.rw INTEGER .1.3.6.1.4.1.326.2.6.2.2.12.1.3 |
alBrGroupTableBridge group table. SEQUENCE OF AlBrGroupEntry .1.3.6.1.4.1.326.2.6.2.2.13 |
alBrGroupEntryBridge group entry. AlBrGroupEntry .1.3.6.1.4.1.326.2.6.2.2.13.1 |
brGroupNumberThe group number by which the group is
identified with.ro INTEGER .1.3.6.1.4.1.326.2.6.2.2.13.1.1 |
brGroupPortsMaskThe ports associated with the group number
identified by the instance of brGroupNumber.
The mask is ascii segments separated by commas.
A value of -1 would invalidate the appropriate
group.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.2.2.13.1.2 |
brGroupNameThe name of the group for which this
entry appliesrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.2.2.13.1.3 |
alBridgeSTPControlWhen set to 2 , disables the spanning tree.
set to 1, enables the spanning tree.rw Enumeration .1.3.6.1.4.1.326.2.6.2.2.14 |
alPortStateTablePer port state information about
spanning tree, dignostics and management. SEQUENCE OF PortStateEntry .1.3.6.1.4.1.326.2.6.2.2.15 |
portStateEntryPort state entry. PortStateEntry .1.3.6.1.4.1.326.2.6.2.2.15.1 |
portStatePortThe port number for this table entryro INTEGER .1.3.6.1.4.1.326.2.6.2.2.15.1.1 |
portStateDiagThe diagnostics state of the portro Enumeration .1.3.6.1.4.1.326.2.6.2.2.15.1.2 |
portStateMgmtThe management state of the portro Enumeration .1.3.6.1.4.1.326.2.6.2.2.15.1.3 |
portStateStpThe spanning tree state of the port.ro INTEGER .1.3.6.1.4.1.326.2.6.2.2.15.1.4 |
portStatePortNameThe name of this portro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.2.2.15.1.5 |
almgmt OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.6.2.3 |
alAutoPortStateTableauto port stat table SEQUENCE OF AutoPortStateEntry .1.3.6.1.4.1.326.2.6.2.3.1 |
autoportStateEntryauto port stat entry. AutoPortStateEntry .1.3.6.1.4.1.326.2.6.2.3.1.1 |
autoPortStatePortThe port number for this table entryro INTEGER .1.3.6.1.4.1.326.2.6.2.3.1.1.1 |
autoPortStateWhether the auto port state detection is
turned on or not.rw Enumeration .1.3.6.1.4.1.326.2.6.2.3.1.1.2 |
autoPortStateThresholdCorresponding to the threshold parameter of
the autoportstate command.rw INTEGER .1.3.6.1.4.1.326.2.6.2.3.1.1.3 |
alLinkStatsCollectWhen set to enable(1), per link stats
collection is enabled; when set to disable(0),
the per link stats are not collected.rw INTEGER .1.3.6.1.4.1.326.2.6.2.3.2 |
alLinkStatsClearWhen set, clears the link stats; otherwise value
0 is returned.rw INTEGER .1.3.6.1.4.1.326.2.6.2.3.3 |
alLinkStatsTablePer link stats table SEQUENCE OF LinkStatsEntry .1.3.6.1.4.1.326.2.6.2.3.4 |
linkStatsEntrylink stats entry.rw LinkStatsEntry .1.3.6.1.4.1.326.2.6.2.3.4.1 |
linkStatsPortPort Numberro INTEGER .1.3.6.1.4.1.326.2.6.2.3.4.1.1 |
linkStatsLinkLink Numberro Counter .1.3.6.1.4.1.326.2.6.2.3.4.1.2 |
linkStatsPktsInPkts In - corresponds to piro Counter .1.3.6.1.4.1.326.2.6.2.3.4.1.3 |
linkStatsOctetsInOctets In - corresponds to oiro Counter .1.3.6.1.4.1.326.2.6.2.3.4.1.4 |
linkStatsBMCastPktsInBmcast Pks In - corresponds to bpiro Counter .1.3.6.1.4.1.326.2.6.2.3.4.1.5 |
linkStatsGiantPktsGiant Pkts - corresponds to gpro Counter .1.3.6.1.4.1.326.2.6.2.3.4.1.6 |
linkStatsFrameErrsFrame Errors - corresponds to faro Counter .1.3.6.1.4.1.326.2.6.2.3.4.1.7 |
linkStatsFCSErrsFCS Errors corresponds to fcsro Counter .1.3.6.1.4.1.326.2.6.2.3.4.1.8 |
linkStatsCodingErrorsThis Counter is incremented when the receiver (RX)
port detects an invalid symbol in the incoming code
sent by the TX port using symbol mode.ro Counter .1.3.6.1.4.1.326.2.6.2.3.4.1.9 |
linkStatsDataRateMismatchThis counter is incremented by one for
each frame received on this port that meets
all of the following conditions: 1) The Collision
Event signal is not asserted 2) The Activity duration
is greater than ValidPacketMinTime 3) The frequency
(data rate) is detectably mismatched from the local
transmit frequencyro Counter .1.3.6.1.4.1.326.2.6.2.3.4.1.10 |
linkStatsJabbersThis Counter is incremented for each CarrierEvent on
this port whose ActivityDuration is greater than the
MAU Jabber Lockup Protection timerro Counter .1.3.6.1.4.1.326.2.6.2.3.4.1.11 |
linkStatsShortEventsThis counter is incremented for each CarrierEvent
on this port with ActivityDuration less than
ShortEventMaxTime.ro Counter .1.3.6.1.4.1.326.2.6.2.3.4.1.12 |
linkStatsRuntsAn event whose length is greater than 74 bit times
but less than 82 bit times shall increment either
the shortEvents counter or the runts counter but not
bothro Counter .1.3.6.1.4.1.326.2.6.2.3.4.1.13 |
linkStatsPortCollisionThis counter is incremented for any CarrierEvent
signal on any port for which the CollisionEvent
signal on this port is also asserted.ro Counter .1.3.6.1.4.1.326.2.6.2.3.4.1.14 |
linkStatsLateCollisionThis counter is incremented for each CarrierEvent
on this port in which the CollIn(X) variable
transitions to the value SQE while the
ActivityDuration
is greater than the LAteEventThreshold.ro Counter .1.3.6.1.4.1.326.2.6.2.3.4.1.15 |
linkStatsAutoPartitionThis counter is incremented each time the
repeater has automatically partitioned this
portro Counter .1.3.6.1.4.1.326.2.6.2.3.4.1.16 |
linkStatsIsolatesThis counter is incremented whenever the port
detects two consecutive carrier integrity
false carriers.ro Counter .1.3.6.1.4.1.326.2.6.2.3.4.1.17 |
linkStatsSaFieldChangesThis counter is incremented for each time that
the rptrAddrTrackLastSourceAddress attribute
for this port has changed.ro Counter .1.3.6.1.4.1.326.2.6.2.3.4.1.18 |
linkStatsLastSaThis object is the SourceAddress of the
last readable frame received by this port.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.2.3.4.1.19 |
alLinkControlTablePer link stats table SEQUENCE OF LinkControlEntry .1.3.6.1.4.1.326.2.6.2.3.5 |
linkControlEntrylink control entry.rw LinkControlEntry .1.3.6.1.4.1.326.2.6.2.3.5.1 |
linkControlPortPort number for this entry.ro INTEGER .1.3.6.1.4.1.326.2.6.2.3.5.1.1 |
linkControlLinkLink number for this entry.ro INTEGER .1.3.6.1.4.1.326.2.6.2.3.5.1.2 |
linkControlEnlStateSetting the value of this object to Enable
(1) will enable the link and setting to Disable(2)
will disable the link.rw Enumeration .1.3.6.1.4.1.326.2.6.2.3.5.1.3 |
linkControlLinkTestLink test status for the link; corresponds to
lt option of the lkd command.ro INTEGER .1.3.6.1.4.1.326.2.6.2.3.5.1.4 |
linkControlPartitionPartitioning state of the linkro INTEGER .1.3.6.1.4.1.326.2.6.2.3.5.1.5 |
linkControlPolarityPolarity of the linkro INTEGER .1.3.6.1.4.1.326.2.6.2.3.5.1.6 |
alPortLinkTablePer port link type SEQUENCE OF PortLinkEntry .1.3.6.1.4.1.326.2.6.2.3.6 |
portLinkEntryport link entry. PortLinkEntry .1.3.6.1.4.1.326.2.6.2.3.6.1 |
portLinkPortThe port number for which the port type
is to be setro INTEGER .1.3.6.1.4.1.326.2.6.2.3.6.1.1 |
portLinkTypeThe type of portrw Enumeration .1.3.6.1.4.1.326.2.6.2.3.6.1.2 |
alFiberStatsTablePer port fiber stats and Fiber Security SEQUENCE OF FiberStatsEntry .1.3.6.1.4.1.326.2.6.2.3.7 |
fiberStatsEntryfiber stat entry. FiberStatsEntry .1.3.6.1.4.1.326.2.6.2.3.7.1 |
fiberStatsPortThe fiber port for which the stats are
requested or the Fiber violation is setro INTEGER .1.3.6.1.4.1.326.2.6.2.3.7.1.1 |
fiberAuiStatusThe fiber aui status for the port that is
specified by the instance of fiberStatsPortro INTEGER .1.3.6.1.4.1.326.2.6.2.3.7.1.2 |
fiberSecurityViolationThe fiber port for which the stats are
requested or the Fiber violation is setrw Enumeration .1.3.6.1.4.1.326.2.6.2.3.7.1.3 |
alPortMonitorCloseSetting the value to close(1), will
turn the port monitoring off.rw INTEGER .1.3.6.1.4.1.326.2.6.2.3.8 |
alPortMonitorTableport monitor table. SEQUENCE OF PortMonitorEntry .1.3.6.1.4.1.326.2.6.2.3.9 |
portMonitorEntryport monitor entry. PortMonitorEntry .1.3.6.1.4.1.326.2.6.2.3.9.1 |
portMonSrcPortThe traffic to/from this port will be monitored
on the portMonDstPortro INTEGER .1.3.6.1.4.1.326.2.6.2.3.9.1.1 |
portMonDstPortThe traffic to/from portMonSrcPort will be
monitored on this portro INTEGER .1.3.6.1.4.1.326.2.6.2.3.9.1.2 |
portMonTrafficTypeSetting this value to 1, will let the port monitor
monitor forwarded traffic; setting to 8 means the
forwarded traffic will not be monitored.rw Enumeration .1.3.6.1.4.1.326.2.6.2.3.9.1.3 |
alRebootSetting the value to Reboot(1), will reboot
the PowerHub.rw INTEGER .1.3.6.1.4.1.326.2.6.2.3.10 |
alPortMonitorViewTableport monitor view table. SEQUENCE OF PortMonitorViewEntry .1.3.6.1.4.1.326.2.6.2.3.11 |
portMonitorViewEntryport monitor view entry. PortMonitorViewEntry .1.3.6.1.4.1.326.2.6.2.3.11.1 |
portMonViewSrcPortThe traffic from this port to the port
designated by portMonViewDstPort will be monitored
on portMonViewMonitorPort.ro INTEGER .1.3.6.1.4.1.326.2.6.2.3.11.1.1 |
portMonViewDstPortThe traffic to this port from the port
designated by portMonViewSrcPort will be monitored
on portMonViewMonitorPort.ro INTEGER .1.3.6.1.4.1.326.2.6.2.3.11.1.2 |
portMonViewMonitorPortThe traffic to portMonViewDstPort from the port
designated by portMonViewSrcPort will be monitored
on portMonViewMonitorPort. The mask is ascii, segments
separated by commas.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.2.3.11.1.3 |
alCfgLocalMediaScopeThis object display the types of local media currently
available on the PH for storing files. The PH4000 and
PH6000 do not support floppy whereas the PH3000 and
PH5000 do not support flash. The flash is optional on
PH6000 & PH7000. All models do support tftpHost save
options. Depending on the value of this object, the
user can specify the appropriate filename and the
media type in other objects for doing the save
operation.ro Enumeration .1.3.6.1.4.1.326.2.6.2.3.12 |
alCfgMediaNameThis object specify the medium name to which the
the powerhub will save the configurations. The value
'none' is returned when user have not set the valid
save medium. Save operation cannot be performed when
value is set to 'none'.rw Enumeration .1.3.6.1.4.1.326.2.6.2.3.13 |
alCfgTftpHostAddrThis object specify the IP address of the tftp host
system to which the configs get saved when the object
alCfgMediaName is set with value tftpHost(3).rw IpAddress .1.3.6.1.4.1.326.2.6.2.3.14 |
alCfgFileNameThis object specify the configuration filename to
which the PH will save the configuration. Depending
on the medium (floppy, flash, or tftpHost) in which
the saving will be done, the filename have to be set
correctly. For example, the filename for floppy and
flash medium cannot exceed 8 characters. The filnames
can be appended with the optional dot character
followed by 3 character extension. The filenames for
tftp host should have been pre-created on the host and
it should be writable by the PH. All tftp file access
restrictions apply.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.326.2.6.2.3.15 |
alCfgSaveOpSave config operation can be performed only when
this object is set to value '1'. This field returns
a dummy value 100 for get operations.rw INTEGER .1.3.6.1.4.1.326.2.6.2.3.16 |