EATON-ATS2-MIB
The MIB module for Eaton ATS (Automatic Transfer Switch).
Main OID:
ats2.1.3.6.1.4.1.534.10.2
102
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
102 total| Object Name |
|---|
enterprises OBJECT IDENTIFIER .1.3.6.1.4.1 |
eaton OBJECT IDENTIFIER .1.3.6.1.4.1.534 |
sts OBJECT IDENTIFIER .1.3.6.1.4.1.534.10 |
ats2The MIB module for Eaton ATS (Automatic Transfer Switch). MODULE-IDENTITY .1.3.6.1.4.1.534.10.2 |
IMPORTSThe MIB module for Eaton ATS (Automatic Transfer Switch). Unknown .1.3.6.1.4.1.534.10.2 |
ats2Ident OBJECT IDENTIFIER .1.3.6.1.4.1.534.10.2.1 |
ats2IdentManufacturerThe manufacturer name.ro DisplayString .1.3.6.1.4.1.534.10.2.1.1 |
ats2IdentModelDevice model name.ro DisplayString .1.3.6.1.4.1.534.10.2.1.2 |
ats2IdentFWVersionDevice F/W version.ro DisplayString .1.3.6.1.4.1.534.10.2.1.3 |
ats2IdentReleaseThe released date.ro DisplayString .1.3.6.1.4.1.534.10.2.1.4 |
ats2IdentSerialNumberDevice serial numberro DisplayString .1.3.6.1.4.1.534.10.2.1.5 |
ats2IdentPartNumberDevice part numberro DisplayString .1.3.6.1.4.1.534.10.2.1.6 |
ats2IdentAgentVersionCommunication Card F/W versionro DisplayString .1.3.6.1.4.1.534.10.2.1.7 |
ats2Measure OBJECT IDENTIFIER .1.3.6.1.4.1.534.10.2.2 |
ats2Input OBJECT IDENTIFIER .1.3.6.1.4.1.534.10.2.2.1 |
ats2InputDephasingThe dephasing in between Source 1 and Source 2.ro INTEGER UNITS "degrees" .1.3.6.1.4.1.534.10.2.2.1.1 |
ats2InputTableThe table of input information. SEQUENCE OF ATSInputEntry .1.3.6.1.4.1.534.10.2.2.2 |
ats2InputEntryThe input information of each source input:
<node>.1 source1
<node>.2 source2 ATSInputEntry .1.3.6.1.4.1.534.10.2.2.2.1 |
ats2InputIndexIndex to input.ro Enumeration .1.3.6.1.4.1.534.10.2.2.2.1.1 |
ats2InputVoltageThe input voltage in front of relay. Units are 0.1 V.ro INTEGER UNITS "0.1 V" .1.3.6.1.4.1.534.10.2.2.2.1.2 |
ats2InputFrequencyThe input frequency. Units are 0.1 Hz.ro INTEGER UNITS "0.1 Hz" .1.3.6.1.4.1.534.10.2.2.2.1.3 |
ats2Output OBJECT IDENTIFIER .1.3.6.1.4.1.534.10.2.2.3 |
ats2OutputVoltageThe output voltage. Units are 0.1 V.ro INTEGER UNITS "0.1 V" .1.3.6.1.4.1.534.10.2.2.3.1 |
ats2OutputCurrentThe output current. Units are 0.1 A.ro INTEGER UNITS "0.1 A" .1.3.6.1.4.1.534.10.2.2.3.2 |
ats2OperationModeThe operation mode.ro Enumeration .1.3.6.1.4.1.534.10.2.2.4 |
ats2Status OBJECT IDENTIFIER .1.3.6.1.4.1.534.10.2.3 |
ats2InputStatus OBJECT IDENTIFIER .1.3.6.1.4.1.534.10.2.3.1 |
ats2InputStatusDephasingThe dephasing status in between Source 1 and Source 2.ro Enumeration .1.3.6.1.4.1.534.10.2.3.1.1 |
ats2InputStatusTableThe table of input status. SEQUENCE OF ATSInputStatusEntry .1.3.6.1.4.1.534.10.2.3.2 |
ats2InputStatusEntryThe input flow status:
<node>.1 source1
<node>.2 source2 ATSInputStatusEntry .1.3.6.1.4.1.534.10.2.3.2.1 |
ats2InputStatusIndexIndex of input entry.ro Enumeration .1.3.6.1.4.1.534.10.2.3.2.1.1 |
ats2InputStatusFrequencyThe status of input frequency.ro Enumeration .1.3.6.1.4.1.534.10.2.3.2.1.2 |
ats2InputStatusGoodThe summarized status of input AC flow.ro Enumeration .1.3.6.1.4.1.534.10.2.3.2.1.3 |
ats2InputStatusInternalFailureThe internal fault status of input.ro Enumeration .1.3.6.1.4.1.534.10.2.3.2.1.4 |
ats2InputStatusVoltageThe status of input voltage.ro Enumeration .1.3.6.1.4.1.534.10.2.3.2.1.5 |
ats2InputStatusUsedThe status of input relay.ro Enumeration .1.3.6.1.4.1.534.10.2.3.2.1.6 |
ats2OutputStatus OBJECT IDENTIFIER .1.3.6.1.4.1.534.10.2.3.3 |
ats2StatusInternalFailureOutput fault.ro Enumeration .1.3.6.1.4.1.534.10.2.3.3.1 |
ats2StatusOutputOutput powered status.ro Enumeration .1.3.6.1.4.1.534.10.2.3.3.2 |
ats2StatusOverloadThe output overload status.ro Enumeration .1.3.6.1.4.1.534.10.2.3.3.3 |
ats2StatusOverTemperatureThe over temperature status.ro Enumeration .1.3.6.1.4.1.534.10.2.3.3.4 |
ats2StatusShortCircuitShort circuit status.ro Enumeration .1.3.6.1.4.1.534.10.2.3.3.5 |
ats2StatusCommunicationLostCommunication failure status.ro Enumeration .1.3.6.1.4.1.534.10.2.3.3.6 |
ats2StatusConfigurationFailureConfiguration failure status.ro Enumeration .1.3.6.1.4.1.534.10.2.3.3.7 |
ats2Config OBJECT IDENTIFIER .1.3.6.1.4.1.534.10.2.4 |
ats2ConfigTime OBJECT IDENTIFIER .1.3.6.1.4.1.534.10.2.4.1 |
ats2ConfigTimeRTCClock value. This could be from either a real-time clock (in which case
it is likely writeable) or from a time server via NTP (probably read-only).
(since 1/1/1970 at 1:00:00).rw UnixTimeStamp .1.3.6.1.4.1.534.10.2.4.1.1 |
ats2ConfigTimeTextDateThe present date in MM/DD/YYYY text format.ro DisplayString .1.3.6.1.4.1.534.10.2.4.1.2 |
ats2ConfigTimeTextTimeThe present time in hh:mm:ss text format.ro DisplayString .1.3.6.1.4.1.534.10.2.4.1.3 |
ats2ConfigInputVoltageRatingThe input voltage rating. Unit is 1 V.ro INTEGER UNITS "1 V" .1.3.6.1.4.1.534.10.2.4.2 |
ats2ConfigInputFrequencyRatingThe input frequency rating. Unit is 1 Hz.ro INTEGER UNITS "Hz" .1.3.6.1.4.1.534.10.2.4.3 |
ats2ConfigOutputVoltageThe output voltage config. Unit is 1 V.rw INTEGER UNITS "1 V" .1.3.6.1.4.1.534.10.2.4.4 |
ats2ConfigPreferredThe preferred source.rw Enumeration .1.3.6.1.4.1.534.10.2.4.5 |
ats2ConfigSensitivityThe AC Blackout Sensitivity.rw Enumeration .1.3.6.1.4.1.534.10.2.4.6 |
ats2ConfigTransferModebehavior configuration when transfering from one source to other source not synchronized.rw Enumeration .1.3.6.1.4.1.534.10.2.4.7 |
ats2ConfigTransferTestThe status of transfer test.ro Enumeration .1.3.6.1.4.1.534.10.2.4.8 |
ats2ConfigBrownoutLowSetting of input brownout low voltage. Unit is 1 V.ro INTEGER UNITS "1 V" .1.3.6.1.4.1.534.10.2.4.9 |
ats2ConfigBrownoutLowDeratedSetting of input brownout low derated voltage. Unit is 1 V.ro INTEGER UNITS "1 V" .1.3.6.1.4.1.534.10.2.4.10 |
ats2ConfigBrownoutHighSetting of input brownout high voltage. Unit is 1 V.ro INTEGER UNITS "1 V" .1.3.6.1.4.1.534.10.2.4.11 |
ats2ConfigHysteresisVoltageHysteresis between loss point and comeback point. Unit is 1 V.ro INTEGER UNITS "1 V" .1.3.6.1.4.1.534.10.2.4.12 |
ats2Environment OBJECT IDENTIFIER .1.3.6.1.4.1.534.10.2.5 |
ats2EnvRemoteTempThe reading of an EMP's temperature sensor.ro INTEGER (-100..200) UNITS "degrees Centigrade" .1.3.6.1.4.1.534.10.2.5.1 |
ats2EnvRemoteHumidityThe reading of an EMP's humidity sensor.ro INTEGER .1.3.6.1.4.1.534.10.2.5.2 |
ats2EnvNumContactsThe number of Contacts in the ats2ContactSenseTable.
This object indicates the number of rows in the
ats2ContactSenseTable.ro INTEGER .1.3.6.1.4.1.534.10.2.5.3 |
ats2ContactSenseTableA list of Contact Sensing table entries.
The number of entries is given by the value of
ats2EnvNumContacts. SEQUENCE OF Ats2ContactsTableEntry .1.3.6.1.4.1.534.10.2.5.4 |
ats2ContactsTableEntryAn entry containing information applicable
to a particular Contact input. Ats2ContactsTableEntry .1.3.6.1.4.1.534.10.2.5.4.1 |
ats2ContactIndexThe Contact identifier; identical to the Contact Number.
This object is not-accessible to MIB browsers, but had to be changed to
read-only to satisfy SMIv2 syntax checkers if it is included in traps.ro INTEGER .1.3.6.1.4.1.534.10.2.5.4.1.1 |
ats2ContactTypeThe normal state for this contact. The 'other' (not 'Normally')
state is the Active state for generating the ats2tdContactActiveNotice
trap. If anyChange(3) is selected, then this trap is sent
any time the contact changes to either Open or Closed.
No traps are sent if the Contact is set to notUsed(4).
In many cases, the configuration for Contacts may be done by other
means, so this object may be read-only.rw Enumeration .1.3.6.1.4.1.534.10.2.5.4.1.2 |
ats2ContactStateThe current state of the Contact input;
the value is based on the open/closed input state
and the setting for ats2ContactType.
When entering the openWithNotice(3) and closedWithNotice(4)
states, no entries added to the ats2AlarmTable, but
the ats2tdContactActiveNotice trap is sent.ro Enumeration .1.3.6.1.4.1.534.10.2.5.4.1.3 |
ats2ContactDescrA label identifying the Contact. This object should be
set by the administrator.rw DisplayString .1.3.6.1.4.1.534.10.2.5.4.1.4 |
ats2EnvRemoteTempLowerLimitThe Lower Limit of the EMP temperature; if ats2EnvRemoteTemp
falls below this value, the ats2RemoteTempBad alarm will occur.rw INTEGER (-100..200) UNITS "degrees Centigrade" .1.3.6.1.4.1.534.10.2.5.5 |
ats2EnvRemoteTempUpperLimitThe Upper Limit of the EMP temperature; if ats2EnvRemoteTemp
rises above this value, the ats2RemoteTempBad alarm will occur.
This value should be greater than ats2EnvRemoteTempLowerLimit.rw INTEGER (-100..200) UNITS "degrees Centigrade" .1.3.6.1.4.1.534.10.2.5.6 |
ats2EnvRemoteHumidityLowerLimitThe Lower Limit of the EMP humidity reading; if ats2EnvRemoteHumidity
falls below this value, the ats2RemoteHumidityBad alarm will occur.rw INTEGER .1.3.6.1.4.1.534.10.2.5.7 |
ats2EnvRemoteHumidityUpperLimitThe Upper Limit of the EMP humidity reading; if ats2EnvRemoteHumidity
rises above this value, the ats2RemoteHumidityBad alarm will occur.
This value should be greater than ats2EnvRemoteHumidityLowerLimit.rw INTEGER .1.3.6.1.4.1.534.10.2.5.8 |
ats2Traps OBJECT IDENTIFIER .1.3.6.1.4.1.534.10.2.10 |
ats2TrapCommunicationLostCommunication with the ATS failed. NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.1 |
ats2TrapCommunicationRecoveredCommunication with the ATS recovered. NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.2 |
ats2TrapOutputPoweredThe ATS powers the load. NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.3 |
ats2TrapOutputNotPoweredThe ATS does not powers the load. NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.4 |
ats2TrapOverloadThe ATS has sensed a critical overload. NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.5 |
ats2TrapNoOverLoadThe critical overload disappeared. NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.6 |
ats2TrapInternalFailureThe ATS has an internal failure (sum of all HW internal failure). NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.7 |
ats2TrapNoInternalFailureThe ATS internal failure disappeared. NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.8 |
ats2TrapSource1NormalSource 1 returns to normal. NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.9 |
ats2TrapSource1OutOfRangeSource 1 out of range. NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.10 |
ats2TrapSource2NormalSource 2 returns to normal. NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.11 |
ats2TrapSource2OutOfRangeSource 2 out of range. NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.12 |
ats2TrapSourceDesynchronizedSource 1 and Source 2 phase are desynchronized. NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.13 |
ats2TrapSourceSynchronizedSource 1 and Source 2 phase are synchronized. NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.14 |
ats2TrapOutputPoweredBySource1Source 1 powers the output. NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.15 |
ats2TrapOutputPoweredBySource2Source 2 powers the output. NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.16 |
ats2TrapRemoteTempLowThe remote temperature, ats2EnvRemoteTemp, has fallen below
the set lower limit, ats2EnvRemoteTempLowerLimit. NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.20 |
ats2TrapRemoteTempHighThe remote temperature, ats2EnvRemoteTemp, has risen above
the set upper limit, xupsEnvRemoteTempUpperLimit. NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.21 |
ats2TrapRemoteTempNormalThe remote temperature, ats2EnvRemoteTemp, is inside the interval
defined by the lower limit and the upper limit. NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.22 |
ats2TrapRemoteHumidityLowThe remote humidity, ats2EnvRemoteHumidity, has fallen below
the set lower limit, ats2EnvRemoteHumidityLowerLimit. NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.23 |
ats2TrapRemoteHumidityHighThe remote humidity, ats2EnvRemoteHumidity, has risen above
the set upper limit, ats2EnvRemoteHumidityUpperLimit. NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.24 |
ats2TrapRemoteHumidityNormalThe remote humidity, ats2EnvRemoteHumidity, is inside the interval
defined by the lower limit and the upper limit. NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.25 |
ats2Contact1ActiveNoticeThe Contact 1 is in its Active state.
The following are the situations that generate this trap:
For ats2ContactType: and ats2ContactState:
normallyOpen(1) and closedWithNotice(4)
normallyClosed(2) and openWithNotice(3)
anyChange(3) and openWithNotice(3) or closedWithNotice(4) NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.26 |
ats2Contact1InactiveNoticeThe Contact 1 has changed to its Inactive state. NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.27 |
ats2Contact2ActiveNoticeThe Contact 2 is in its Active state.
The following are the situations that generate this trap:
For ats2ContactType: and ats2ContactState:
normallyOpen(1) and closedWithNotice(4)
normallyClosed(2) and openWithNotice(3)
anyChange(3) and openWithNotice(3) or closedWithNotice(4) NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.28 |
ats2Contact2InactiveNoticeThe Contact 2 has changed to its Inactive state. NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.29 |
ats2TestTrapSent whenever the trap test feature is used by the communication card. NOTIFICATION-TYPE .1.3.6.1.4.1.534.10.2.10.40 |