DSR4410MD-MIB
AI MIB Summary
The DSR4410MD-MIB module provides managed objects for monitoring and configuring the D-Link DSR-4410MD Dynamic Service Router, specifically exposing metrics for interface status, traffic counters, routing table entries, and system resource utilization. This MIB enables SNMP-based supervision of the device's Layer 3 forwarding performance, link state transitions, and hardware health parameters within enterprise network infrastructure.
The managed objects for the dsr mib.
Main OID:
dsr.1.3.6.1.4.1.1166.1.621
210
Objects
Active
Status
2
Dependencies
Imported Objects
Objects
210 total| Object Name |
|---|
org OBJECT IDENTIFIER .1.3 |
dod OBJECT IDENTIFIER .1.3.6 |
internet OBJECT IDENTIFIER .1.3.6.1 |
private OBJECT IDENTIFIER .1.3.6.1.4 |
enterprises OBJECT IDENTIFIER .1.3.6.1.4.1 |
giMIB OBJECT IDENTIFIER .1.3.6.1.4.1.1166 |
giproducts OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1 |
dsrThe managed objects for the dsr mib. MODULE-IDENTITY .1.3.6.1.4.1.1166.1.621 |
videoMib OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.1 |
videoOutput525LinesThe format of the output video that the unit renders when the unit is tuned to a 525 line video broadcast signal.rw Enumeration .1.3.6.1.4.1.1166.1.621.1.1 |
videoOutput625LinesThe format of the output video that the unit renders when the unit is tuned to a 625 line video broadcast signal.rw Enumeration .1.3.6.1.4.1.1166.1.621.1.2 |
aspectRatioInputThe aspect ratio of the video that is carried in the broadcast signal.ro Enumeration .1.3.6.1.4.1.1166.1.621.1.3 |
aspectRatioOutputThe aspect ratio of the output video signal.rw Enumeration .1.3.6.1.4.1.1166.1.621.1.4 |
rfPortsMib OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.2 |
rfPortsSetup OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.2.1 |
port1 OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.2.1.1 |
port1SetupModeWhen the setup mode is set to manual the satellite name and polarity has to befined by the user. When the port mode is set to auto the Satellite name and polarity will be automatically set during the first channel change.rw Enumeration .1.3.6.1.4.1.1166.1.621.2.1.1.1 |
port1SatelliteA 2 to 3 character abbreviation of the name of the satellite to which the RF port is associated.rw OCTET STRING ( SIZE ( 2 .. 3 ) ) .1.3.6.1.4.1.1166.1.621.2.1.1.2 |
port1PolarityThe polarity of the RF input applied to the RF port. The undefined value is not writeable; instead, undefined can only be set by the uplink.rw Enumeration .1.3.6.1.4.1.1166.1.621.2.1.1.3 |
port2 OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.2.1.2 |
port2SetupModeWhen the setup mode is set to manual the satellite name and polarity has to befined by the user. When the port mode is set to auto the Satellite name and polarity will be automatically set during the first channel change.rw Enumeration .1.3.6.1.4.1.1166.1.621.2.1.2.1 |
port2SatelliteA 2 to 3 character abbreviation of the name of the satellite to which the RF port is associated.rw OCTET STRING ( SIZE ( 2 .. 3 ) ) .1.3.6.1.4.1.1166.1.621.2.1.2.2 |
port2PolarityThe polarity of the RF input applied to the RF port. The undefined value is not writeable; instead, undefined can only be set by the uplink.rw Enumeration .1.3.6.1.4.1.1166.1.621.2.1.2.3 |
manualTune OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.2.2 |
activePortThe RF port that is active during a manual tune.rw Enumeration .1.3.6.1.4.1.1166.1.621.2.2.1 |
modeThe frequency plan of the satellite to which the unit tunes during installation. The unit accepts a C-Band satellite transponder number when the selection is xpndr. The unit accepts a discrete frequency value when the selection is lfreqrw Enumeration .1.3.6.1.4.1.1166.1.621.2.2.2 |
transponderNumberThe transponder number to which the unit tunes during installation This in turn specifies the L-Band frequency to which the unit tunes during installation. This value is valid only when the FrequencyPlan selection is xpndr. Value -1 indicates its Not applicable.rw INTEGER ( 1 .. 24 ) .1.3.6.1.4.1.1166.1.621.2.2.3 |
frequencyThe L-band frequency, in MHz, during a manual tune. A new manual tune is initiated when this object is set.This value is valid only of the Frequency Plan selection is lfreq. Value -1 indicates its Not applicable.rw INTEGER ( 950 .. 2150 ) .1.3.6.1.4.1.1166.1.621.2.2.4 |
dvbSymbolRateThe symbol-rate to be tuned to in units of sps. A new manual tune is initiated when this object is set. Value -1 indicates its Not applicable.rw INTEGER ( 0 .. 99999999 ) .1.3.6.1.4.1.1166.1.621.2.2.5 |
dvbCodeRateThe code rate of the channel being tuned to. A new manual tune is initiated when this object is set. Value -1 indicates its Not applicable.rw Enumeration .1.3.6.1.4.1.1166.1.621.2.2.6 |
symbolCodeBitThe symbol, code rate, and bitstream select combination during a manual tune. A new manual tune is initiated when this object is set. The symbol rate takes eight possible values: 29.3, 19.5, 14.6, 11.7, 9.76, 7.32, 4.88, and 3.25 Msps. The code rate also takes eight possible values: 7/8, 5/6, 4/5, 3/4, 2/3, 3/5, 1/2, and 5/11. The bitstream select takes two possible values: combined and split. Value -1 indicates its Not applicable.rw Enumeration .1.3.6.1.4.1.1166.1.621.2.2.8 |
modulationModeThe modulation mode to be used for the manual tune. A new manual tune is initiated when this object is set.rw Enumeration .1.3.6.1.4.1.1166.1.621.2.2.9 |
psk8SymbolRateThe symbol-rate to be tuned to in units of sps. A new manual tune is initiated when this object is set. Value -1 indicates its Not applicable.rw INTEGER ( 1000000 .. 30000000 ) .1.3.6.1.4.1.1166.1.621.2.2.10 |
psk8CodeRateThe code rate of the channel being tuned to. A new manual tune is initiated when this object is set. Value -1 indicates its Not applicable.rw Enumeration .1.3.6.1.4.1.1166.1.621.2.2.11 |
dvbS2symbolRateThe symbol-rate to be tuned to in units of sps. A new manual tune is initiated when this object is set. Value -1 indicates its Not applicable.rw INTEGER ( 1000000 .. 33000000 ) .1.3.6.1.4.1.1166.1.621.2.2.12 |
dvbS2codeRateThe code rate of the channel being tuned to. A new manual tune is initiated when this object is set. Value -1 indicates its Not applicable.rw Enumeration .1.3.6.1.4.1.1166.1.621.2.2.13 |
channelMib OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.3 |
channelSelect OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.3.1 |
vctIDThe virtual channel table number.rw INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.3.1.1 |
channelNumberThe virtual channel.rw INTEGER ( 0 .. 4095 ) .1.3.6.1.4.1.1166.1.621.3.1.2 |
channelStatus OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.3.2 |
transponderThe current transponder name (alpha/numeric) as received from the uplink.A Blank string is returned if the name is not available .ro OCTET STRING ( SIZE ( 0 .. 31 ) ) .1.3.6.1.4.1.1166.1.621.3.2.1 |
sourceThe name of the current source signal as received from the uplink.A Blank string is returned if the name is not available .ro OCTET STRING ( SIZE ( 0 .. 255 ) ) .1.3.6.1.4.1.1166.1.621.3.2.2 |
satelliteStatusThe name of the current satellite as received from the uplink. A Blank string is returned if the name is not available .ro OCTET STRING ( SIZE ( 0 .. 15 ) ) .1.3.6.1.4.1.1166.1.621.3.2.3 |
serviceSelectionMib OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.4 |
mpegServiceNumberThe MPEG service number which the IRD has to play.rw INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.4.1 |
unitControlMib OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.5 |
unitControl OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.5.1 |
contrastThe LCD contrast, with 0 representing the least contrast and 30 representing the most.rw INTEGER (0 .. 30) .1.3.6.1.4.1.1166.1.621.5.1.1 |
asiEnableOption to enable or disbale the ASI output. Note that lock-off is a read only value used by the uplink to lock asiEnable. It cannot be set via SNMP. Also, when this value is lock-off, this entire field is read only.rw Enumeration .1.3.6.1.4.1.1166.1.621.5.1.3 |
lnbPowerOption to enable or disable LNB Power.rw Enumeration .1.3.6.1.4.1.1166.1.621.5.1.6 |
resetIRDOption to reboot the box.rw Enumeration .1.3.6.1.4.1.1166.1.621.5.1.7 |
formatRateFormat and rate of the ASI outputrw Enumeration .1.3.6.1.4.1.1166.1.621.5.1.8 |
audioMib OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.6 |
audioConfig OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.6.1 |
audio1Config OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.6.1.1 |
audio1GainControlIn audio gain control joint, only the left audio channel is edited. The right audio channel gain will be set to the left.ro Enumeration .1.3.6.1.4.1.1166.1.621.6.1.1.1 |
audio1LeftGainThe left audio signal output level from -20 dB to 0 dB, in 1 dB increments.rw INTEGER ( -20 .. 0 ) .1.3.6.1.4.1.1166.1.621.6.1.1.2 |
audio1RightGainThe right audio signal output level from -20 dB to 0 dB, in 1 dB increments.ro INTEGER ( -20 .. 0 ) .1.3.6.1.4.1.1166.1.621.6.1.1.3 |
audio1DiagNormThis varaiables enables and diables the audio dialog normalizationrw Enumeration .1.3.6.1.4.1.1166.1.621.6.1.1.4 |
audio1DownMixThe mode of the audio output. The unit downmixes the input audio to the selected channel mode.rw Enumeration .1.3.6.1.4.1.1166.1.621.6.1.1.5 |
audio1CompressionThe degree of audio level compression.rw Enumeration .1.3.6.1.4.1.1166.1.621.6.1.1.6 |
audio2Config OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.6.1.2 |
audio2GainControlIn audio gain control joint, only the left audio channel is edited. The right audio channel gain will be set to the left.ro Enumeration .1.3.6.1.4.1.1166.1.621.6.1.2.1 |
audio2LeftGainThe left audio signal output level from -20 dB to 0 dB, in 1 dB increments.rw INTEGER ( -20 .. 0 ) .1.3.6.1.4.1.1166.1.621.6.1.2.2 |
audio2RightGainThe right audio signal output level from -20 dB to 0 dB, in 1 dB increments.ro INTEGER ( -20 .. 0 ) .1.3.6.1.4.1.1166.1.621.6.1.2.3 |
audio2DiagNormThis varaiables enables and diables the audio dialog normalizationrw Enumeration .1.3.6.1.4.1.1166.1.621.6.1.2.4 |
audio2DownMixThe mode of the audio output. The unit downmixes the input audio to the selected channel mode .rw Enumeration .1.3.6.1.4.1.1166.1.621.6.1.2.5 |
audio2CompressionThe degree of audio level compression.rw Enumeration .1.3.6.1.4.1.1166.1.621.6.1.2.6 |
audioOutput OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.6.2 |
audio1Output OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.6.2.1 |
audio1LeftLanguageThe language for the audio1 . This 5-character language string is formatted as three letters followed by two numbers. The 2-digit number represents the order of the 3-letter language in the service, e.g., eng01 denotes the second English component that is carried in the active service. The unit processes the default language when the preferred language setting is def (In this case the string is only 3 character wide). Note that the language string is converted to lower case automatically when this configuration is to be appliedrw OCTET STRING ( SIZE ( 3 | 5 ) ) .1.3.6.1.4.1.1166.1.621.6.2.1.1 |
audio1RightLanguageThe language for the right audio channel when the AudioDownMix selection is dualMono. When the AudioDownMix is not dualMono the value mirrors the audio1LeftLanguage and any changes to this value does not have any effect. This is a 3(def) or 5(e.g., eng01) character string similar to the left language string. Note that the language string is converted to lower case automatically when this configuration is to be appliedrw OCTET STRING ( SIZE ( 3 | 5 ) ) .1.3.6.1.4.1.1166.1.621.6.2.1.2 |
audio1LeftLanguageStatusThe language of the left audio channel being presented by the IRD. This is a 3(def) or 5(e.g., eng01) character string of the similar format as of the audio1LeftLanguage.ro OCTET STRING ( SIZE ( 3 | 5 ) ) .1.3.6.1.4.1.1166.1.621.6.2.1.3 |
audio1RightLanguageStatusThe language of the right audio channel being presented by the IRD. This is a 3(def) or 5(e.g., eng01) character string of the similar format as of the audio1LeftLanguage. Note that the language string is converted to lower case automatically when this configuration is to be appliedro OCTET STRING ( SIZE ( 3 | 5 ) ) .1.3.6.1.4.1.1166.1.621.6.2.1.4 |
audio2Output OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.6.2.2 |
audio2LeftLanguageThe language for the audio1 . This 5-character language string is formatted as three letters followed by two numbers. The 2-digit number represents the order of the 3-letter language in the service, e.g., eng01 denotes the second English component that is carried in the active service. The unit processes the default language when the preferred language setting is def(in this case. string is 3 letters wide). Note that the language string is converted to lower case automatically when this configuration is to be appliedrw OCTET STRING ( SIZE ( 3 | 5 ) ) .1.3.6.1.4.1.1166.1.621.6.2.2.1 |
audio2RightLanguageThe language for the right audio channel when the AudioDownMix selection is dualMono. When the AudioDownMix is not dualMono the value mirrors the audio2LeftLanguage and any changes to this value does not have any effect. This is a 3(def) or 5(e.g., eng01) character string of the similar format as of the audio2LeftLanguage. Note that the language string is converted to lower case automatically when this configuration is to be appliedrw OCTET STRING ( SIZE ( 3 | 5 ) ) .1.3.6.1.4.1.1166.1.621.6.2.2.2 |
audio2LeftLanguageStatusThe language of the left audio channel being presented by the IRD. This is a 3(def) or 5(e.g., eng01) character string of the similar format as of the audio2LeftLanguage. Note that the language string is converted to lower case automatically when this configuration is to be appliedro OCTET STRING ( SIZE ( 3 | 5 ) ) .1.3.6.1.4.1.1166.1.621.6.2.2.3 |
audio2RightLanguageStatusThe language of the right audio channel being presented by the IRD. This is a 3(def) or 5(e.g., eng01) character string of the similar format as of the audio2LeftLanguage. Note that the language string is converted to lower case automatically when this configuration is to be appliedro OCTET STRING ( SIZE ( 3 | 5 ) ) .1.3.6.1.4.1.1166.1.621.6.2.2.4 |
dataMib OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.7 |
dataStatus OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.7.1 |
ethernetIPRetrieves whether the select channel contains IP data, as defined in the downloaded network data from the uplink.ro Enumeration .1.3.6.1.4.1.1166.1.621.7.1.1 |
textSetup OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.7.2 |
subtitleLanguageThe selected subtitle track. Applicable when the selected channel carries multiple subtitle tracks. The 5-character string has the following representation: sssdd where sss = 3-char ISO 639 code for the subtitle language dd = 2-digits indicating the occurrence of the specified language 'ENG02' would select, for example, the subtitle track for the second occurrence of English subtitles. To turn the subtitle off, enter 'Off01' or 'Off00' at the browser. The user must enter the ordinal.rw OCTET STRING ( SIZE ( 1 .. 5 ) ) .1.3.6.1.4.1.1166.1.621.7.2.1 |
subtitleLanguageStatusThe subtitle language currently being presented by the IRDro OCTET STRING ( SIZE ( 1 .. 5 ) ) .1.3.6.1.4.1.1166.1.621.7.2.2 |
subtitleDisplayThe subtitle language currently being presented by the IRDrw Enumeration .1.3.6.1.4.1.1166.1.621.7.2.3 |
ethernet10_100 OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.7.3 |
ipAddressThe IP address of the snmp port 1, in the common dotted-decimal format.ro IpAddress .1.3.6.1.4.1.1166.1.621.7.3.1 |
subnetMaskThe subnet mask of the snmp port 1, in the dotted-decimal format.ro IpAddress .1.3.6.1.4.1.1166.1.621.7.3.2 |
defaultGatewayThe IP address of the gateway that is used by the snmp port 1, in the dotted-decimal format.ro IpAddress .1.3.6.1.4.1.1166.1.621.7.3.3 |
macAddrThe ethernet 1 MAC address in hh:hh:hh:hh:hh:hh format.ro OCTET STRING ( SIZE ( 17 ) ) .1.3.6.1.4.1.1166.1.621.7.3.4 |
ethernetGigE OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.7.4 |
gigEipAddressThe IP address of the gigE port, in the common dotted-decimal format.rw IpAddress .1.3.6.1.4.1.1166.1.621.7.4.1 |
gigEsubnetMaskThe subnet mask of the gigE port, in the dotted-decimal format.rw IpAddress .1.3.6.1.4.1.1166.1.621.7.4.2 |
gigEgatewayThe IP address of the gateway that is used by the gigE port, in the dotted-decimal format.rw IpAddress .1.3.6.1.4.1.1166.1.621.7.4.3 |
gigEmacAddrThe gigEthernet MAC address in hh:hh:hh:hh:hh:hh format.ro OCTET STRING ( SIZE ( 17 ) ) .1.3.6.1.4.1.1166.1.621.7.4.4 |
gigEmodeThe gigEthernet mode is one of the following values MPTS,disabled,TS-DSMCC or DSM-CC.rw Enumeration .1.3.6.1.4.1.1166.1.621.7.4.5 |
mptsIpAddrThe MPTS IP address of the gigE port in the dotted-decimal format.rw IpAddress .1.3.6.1.4.1.1166.1.621.7.4.6 |
mptsPortThe port associated with the MPTS IP address.rw INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.7.4.7 |
extHardwareMib OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.8 |
alarms OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.8.1 |
alarmTriggerThe trigger condition for which the alarm is activated. When the alarm is activated the Alarm LED illuminates and the alrm relay indicates an alarm condition. The alarm is activated for any of the following conditions 1. The tuner loses lock when the input is RF 2. The unit is not authorized to access the selected service 3. The unit loses video When Auto is selected the alarm activates for any of these conditions and when Disabled is selected the alarm does not activate for any condition.rw Enumeration .1.3.6.1.4.1.1166.1.621.8.1.2 |
alarmTestA manual test of the alarm indicators. Setting ON places the unit in the alarm condition.rw Enumeration .1.3.6.1.4.1.1166.1.621.8.1.3 |
statusMib OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.9 |
accessControl OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.9.1 |
unitAddressThe unit's electronic address in the following format: ddd-ddddd-ddddd-ddd where d = decimal digit.ro OCTET STRING ( SIZE ( 19 ) ) .1.3.6.1.4.1.1166.1.621.9.1.1 |
tvPasscardThe electronic address of the TV Pass Card, if present, in the unit address format. When no TV Pass Card is present the value returned is 'Not inserted'.ro OCTET STRING ( SIZE ( 26 ) ) .1.3.6.1.4.1.1166.1.621.9.1.2 |
firmware OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.9.2 |
bootVersionThe version of the boot code.ro OCTET STRING ( SIZE ( 6 ) ) .1.3.6.1.4.1.1166.1.621.9.2.1 |
fpgaVersionThe version of the fpga.ro OCTET STRING ( SIZE ( 6 ) ) .1.3.6.1.4.1.1166.1.621.9.2.2 |
firmwareVersionThe version of firmware code.ro OCTET STRING ( SIZE ( 6 ) ) .1.3.6.1.4.1.1166.1.621.9.2.3 |
upgradeFirmwareVersionThe upgrade version of firmware code.ro OCTET STRING ( SIZE ( 6 ) ) .1.3.6.1.4.1.1166.1.621.9.2.4 |
diagnosticMib OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.10 |
screenDisplay OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.10.1 |
diagnosticScreenThe diagnostic screen that is to be presented by the unit on the video output.rw Enumeration .1.3.6.1.4.1.1166.1.621.10.1.1 |
clearCountersClears the counters in the on-screen diagnostics to zero.rw Enumeration .1.3.6.1.4.1.1166.1.621.10.1.2 |
testSignals OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.10.2 |
videoTestPatternThe full-field video test pattern that is presented by the unit on the video output.rw Enumeration .1.3.6.1.4.1.1166.1.621.10.2.1 |
audio1TestPatternThe audio test signal that is outputted by the unit for audio 1. The following options are available: o 1000 Hz @ +16 dBm (for mono) o 4040, 3960 Hz @ + 4dBm each (for left and right) o OFFrw Enumeration .1.3.6.1.4.1.1166.1.621.10.2.2 |
audio2TestPatternSee the DESCRIPTION for the audio1TestPattern object.rw Enumeration .1.3.6.1.4.1.1166.1.621.10.2.3 |
cueToneSignalThe cue tone test signal.The unit generates a cue test tone sequence consisting of 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, *, #, A, B, C, D. The unit repeats the cue test tone sequence when enabled. The unit generates a cue tone test tone sequence with a 50 msec tone and inter-tone duration, a 2 second interval between sequences, and immediate activation. When the users set it to On via SNMP. Cuetones are played continuously.rw Enumeration .1.3.6.1.4.1.1166.1.621.10.2.4 |
vits OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.10.3 |
waveformThe VITS test pattern that is presented by the unit on the the video output.rw Enumeration .1.3.6.1.4.1.1166.1.621.10.3.1 |
fieldThe field on which the VITS test pattern is presented by the unit on the video output. 'n/a' is a read-only value that the unit returns when the waveform object is set to 'transmitted' or 'disabled'.rw Enumeration .1.3.6.1.4.1.1166.1.621.10.3.2 |
lineThe line into which the VITS test pattern is presented by the unit on the video output. 'n/a' is a read-only value that the unit returns when the waveform object is set to 'transmitted' or 'disabled'.rw Enumeration .1.3.6.1.4.1.1166.1.621.10.3.3 |
signalStatus OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.11 |
acquisitionStateThe acquisition state for the active signalro Enumeration .1.3.6.1.4.1.1166.1.621.11.1 |
authorizationStateThe authorization state for viewing the current signal. This object mirrors the 'Auth State' field in the Fast Facts 1 OSD.ro Enumeration .1.3.6.1.4.1.1166.1.621.11.2 |
encryptionModeThe encryption mode of the current signal. This object mirrors the 'Encryption' field in the Fast Facts 1 OSD.ro Enumeration .1.3.6.1.4.1.1166.1.621.11.3 |
unitAddrThe unit's electronic address in the following format: ddd-ddddd-ddddd-ddd where d = decimal digit. This object mirrors the 'Unit' field in the Fast Facts 1 OSD.ro OCTET STRING ( SIZE ( 19 ) ) .1.3.6.1.4.1.1166.1.621.11.4 |
vctIDFastThe current virtual channel table number. This object mirrors the 'VCT ID' field in the Fast Facts 1 OSD.ro INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.11.5 |
channelNumThe virtual channel number of the current signal. This object mirrors the 'VC #' field in the Fast Facts 1 OSD.ro INTEGER ( 1 .. 4095 ) .1.3.6.1.4.1.1166.1.621.11.6 |
serviceNumberThe MPEG-2 service number, as indicated in the virtual channel map, for the current signal. This object mirrors the 'Service #' field in the Fast Facts 1 OSD.ro INTEGER ( 1 .. 65535 ) .1.3.6.1.4.1.1166.1.621.11.7 |
signalQualityThe RF quality level of the current signal. This object mirrors the 'Signal Quality' field in the Fast Facts 1 OSD.ro INTEGER ( 0 .. 100 ) .1.3.6.1.4.1.1166.1.621.11.8 |
signalPowerThe RF power level of the current signal, and measured in units of 0.1 dBm. For example, '-650' represents -65.0 dBm.ro INTEGER ( -800 .. 0 ) .1.3.6.1.4.1.1166.1.621.11.9 |
ebNoThe signal to noise ration, Eb/No, of the current signal, and measured in units of 0.1 dB. For example, '-20' represents -2.0 dB '150' represents +15.0 dB This object mirrors the 'Eb/No' field in the Fast Facts 1 OSD.ro INTEGER ( -30 .. 150 ) .1.3.6.1.4.1.1166.1.621.11.10 |
symbolRateThe symbol rate of the current signal. This object mirrors the 'Symbol Rate' field in the Fast Facts 1 OSD.ro Enumeration .1.3.6.1.4.1.1166.1.621.11.11 |
fecRateThe FEC rate of the current signal. This object mirrors the 'FEC Rate' field in the Fast Facts 1 OSD.ro Enumeration .1.3.6.1.4.1.1166.1.621.11.12 |
freqThe frequency of the L-band signal, in kHz, that is applied to the antenna connector on the unit's back panel. This object mirrors the 'Frequency' field in the Fast Facts 1 OSD.ro INTEGER ( 950000 .. 2150000 ) .1.3.6.1.4.1.1166.1.621.11.13 |
satelliteNameA 2 to 4 character satellite reference name, as indicated in the virtual channel map, for the current signal. This object mirrors the 'Sat' field in the Fast Facts 1 OSD.ro OCTET STRING ( SIZE ( 1 .. 4 ) ) .1.3.6.1.4.1.1166.1.621.11.14 |
xpndrNumberThe transponder number of the satellite, as indicated in the virtual channel map, for the current signal. A value of zero indicates the first transponder, and so on. This object mirrors the '/Xpndr' field in the Fast Facts 1 OSD.ro INTEGER ( 0 .. 63 ) .1.3.6.1.4.1.1166.1.621.11.15 |
polarizationThe polarization, as indicated in the virtual channel map, for the current signal. This object mirrors the 'Polarization' field in the Fast Facts 1 OSD.ro Enumeration .1.3.6.1.4.1.1166.1.621.11.16 |
muxStatusThe multiplex format of the active L-Band signalro Enumeration .1.3.6.1.4.1.1166.1.621.11.17 |
ledStatus OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.12 |
signalLEDThe Signal LED is on (illuminated) when the unit recognizes the signal as a DigiCipher II signal. This object mirrors the LED on the front panelro Enumeration .1.3.6.1.4.1.1166.1.621.12.1 |
authorizedLEDThe Authorized LED is on (illuminated) when the Signal LED is on and either (1) the programmer has transmitted the access messages to allow the unit to decrypt the signal or (2) the signal has been transmitted in an unencrypted of fixed encrypted mode. This object mirrors the LED on the front panelro Enumeration .1.3.6.1.4.1.1166.1.621.12.2 |
alarmConditionLEDThe Alarm condition LED is on (illuminated) when the IRD is in alarm statero Enumeration .1.3.6.1.4.1.1166.1.621.12.3 |
downloadLEDThe Download LED is on ( illuminated ) when an active download is in progressro Enumeration .1.3.6.1.4.1.1166.1.621.12.8 |
retuneMonitorMIB OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.13 |
retuneMonitorEnableEnables retune monitoring by the IRD. When read, this leaf provides the actual enable/disable status of the retune monitoring function in the IRD, and not just the last value that was written to this leaf. The IRD resets retuneMsgStatistic and all entries in the retuneMsgTable each time it receives an enable message; toggling enable/disable/enable is not required for this reset.rw Enumeration .1.3.6.1.4.1.1166.1.621.13.1 |
retuneMsgStatisticThe total number of new retune messages. This counter is incremented whenever the IRD detects a new retune message, but is not incremented by each instance (duplicate) of a retune message. This counter provides a useful troubleshooting tool for determining whether the IRD is detecting any retune messages. Range = 0x0000 - 0xFFFF. Note: This counter is not incremented for every possible retune message. This counter is only incremented when a retune becomes active. The IRD ignores retune messages in which the activation time is still in the future. The IRD also ignores any retune message if the activation time is further in the past than the current retune for the same virtual network.ro INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.13.2 |
retuneMsgVirtNetworkIDindexA table of retune messages is indexed by this target virtual network ID. This table does not have entries for each instance (duplicate) of a retune message that the IRD receives because the uplink repeatedly broadcasts instances of each retune message for the duration of the virtual network program. Instead, this table presents select metrics describing the retune message, as described below. Each table entry pertains to the most recent active retune message. A retune message is considered active when the activation time is in the past. The IRD replaces the current retuneMsgEntry when a new retune message is received having an activation time that is in the past but nearer to the present time than is the activation time of the current retuneMsgEntry. The IRD ignores retune messages in which the activation time is in the future. The virtual network ID indicates which retune message is targeted. This leaf serves as the index for the table. Make sure this index is set prior to accessing the following retune message parameters. Range = 1 - 256.rw INTEGER ( 0 .. 255 ) .1.3.6.1.4.1.1166.1.621.13.3 |
retuneMsgVCTidThe target virtual channel map ID of the most recent active retune message. Range = 0 - 0xFFFF.ro INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.13.4 |
retuneMsgVirtChannelThe target virtual channel of the most recent active retune message. Range = 0 - 4095.ro INTEGER ( 0 .. 4095 ) .1.3.6.1.4.1.1166.1.621.13.5 |
retuneMsgActivationTimeThe activation time of the most recent active retune message. The activation time is a 32-bit count of GPS seconds since January 6, 1980, representing the time at which the retune is scheduled to occur. Past activation times are interpreted as immediate activation.ro OCTET STRING ( SIZE ( 1 .. 4 ) ) .1.3.6.1.4.1.1166.1.621.13.6 |
retuneMsgCRCThe 4-byte CRC value of the most recent active retune message.ro OCTET STRING ( SIZE ( 1 .. 4 ) ) .1.3.6.1.4.1.1166.1.621.13.7 |
retuneMsgCntThe total number of instances that the IRD has received for the most recent active retune message. Range = 0 - 0xFFFF. Note: this counter is incremented when a retune message is received for which the CRC of that retune message matches the CRC of the current retune message (i.e., the value of retuneMsgCRC).ro INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.13.8 |
identificationGroup OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.14 |
identMIBVersionThe version number of this MIB.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1166.1.621.14.1 |
identUnitModelThe unit model of this IRD.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1166.1.621.14.2 |
acpMib OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.15 |
acpModeSetup mode for the authorization control processor.rw Enumeration .1.3.6.1.4.1.1166.1.621.15.1 |
acpIndexNumber uniquely identifying the ACP and keystream pair.rw INTEGER ( 0 .. 63 ) .1.3.6.1.4.1.1166.1.621.15.2 |
acpProgramThe MPEG service number of the program.rw INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.15.3 |
acpUnitAddressThe electronic address of the selected ACP in the following format: ddd-ddddd-ddddd where d = decimal digit.ro OCTET STRING ( SIZE ( 15 ) ) .1.3.6.1.4.1.1166.1.621.15.4 |
acpKeyStreamThe selected keystream.ro INTEGER ( 0 .. 3 ) .1.3.6.1.4.1.1166.1.621.15.5 |
acpAuthStateThis field displays the authorization status of the ACP for the current Service association. AU -- Authorization NA -- Not Authorized The unit presents dashes when no information is availablero OCTET STRING ( SIZE ( 2 ) ) .1.3.6.1.4.1.1166.1.621.15.6 |
acpEncryptModeThis field displays the Encryption Mode of the service being decrypted by the selected ACP. The different values are FP - Fixed Program Key FW - Fixed Working Key S - Scrambled ZK - Unencrypted The unit presents dashes when no information is availablero OCTET STRING ( SIZE ( 1 .. 2 ) ) .1.3.6.1.4.1.1166.1.621.15.7 |
testMib OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.16 |
audio OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.16.1 |
primaryAudioLockGives Primary Audio is locked or notro Enumeration .1.3.6.1.4.1.1166.1.621.16.1.1 |
secondaryAudioLockGives Secondary Audio is locked or notro Enumeration .1.3.6.1.4.1.1166.1.621.16.1.2 |
primaryAudioPIDGives Primary Audio PIDro INTEGER ( 0 .. 8191 ) .1.3.6.1.4.1.1166.1.621.16.1.4 |
secondaryAudioPIDGives Secondary Audio PIDro INTEGER ( 0 .. 8191 ) .1.3.6.1.4.1.1166.1.621.16.1.5 |
video OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.16.2 |
videoLockGives Video is locked or notro Enumeration .1.3.6.1.4.1.1166.1.621.16.2.1 |
videoPIDGives video PIDro INTEGER ( 0 .. 8191 ) .1.3.6.1.4.1.1166.1.621.16.2.2 |
codeDownload OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.16.3 |
codeDownloadBitMonitor the Code Download process 0 - off 1 - onro Enumeration .1.3.6.1.4.1.1166.1.621.16.3.1 |
irdStatus OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.16.4 |
falseLock OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.16.4.1 |
falseLockStatusChecks for false lockro Enumeration .1.3.6.1.4.1.1166.1.621.16.4.1.1 |
alarmLedStatus OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.16.4.2 |
alarmLEDBlinkStatus0 - LED is not blinking(OFF/ON) 1 - LED is blinkingro Enumeration .1.3.6.1.4.1.1166.1.621.16.4.2.1 |
messages OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.16.5 |
patMsgCountGives PAT Message Countro INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.16.5.1 |
caMsgCountGives CA Message Countro INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.16.5.2 |
pmtMsgCountGives PMT message Countro INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.16.5.3 |
niMsgCountGives Network Information Message Countro INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.16.5.4 |
networkTextMsgCountGives Network text Message Countro INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.16.5.5 |
virtualChannelMsgCountGives Virtual channel message Countro INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.16.5.6 |
subtitleMsgCountGives Subtitle Message Countro INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.16.5.7 |
coMsgCountGives Channel Override Message Countro INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.16.5.8 |
dwnldPreMsgCountGives Download preamble message Countro INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.16.5.9 |
dwnldMsgCountGives Download Message Countro INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.16.5.10 |
emmMsgCountGives EMM Message Countro INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.16.5.11 |
fingerPrintMessageCountGives Finger Print message Countro INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.16.5.12 |
hcmMsgCountGives hardware control Message Countro INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.16.5.13 |
uimMsgCountGives Unit information message Countro INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.16.5.14 |
evenBlkoutMsgCountGives Event Blckout Message message Countro INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.16.5.15 |
rf OBJECT IDENTIFIER .1.3.6.1.4.1.1166.1.621.16.6 |
frequencyOffsetThe acquired offset of the L-band frequency in MHz.ro INTEGER ( -100 .. 100 ) .1.3.6.1.4.1.1166.1.621.16.6.1 |
berThis displays Bit Errors.ro INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.16.6.2 |
ebnoThis displays the Eb/No measured in the IRD.ro INTEGER ( -10 .. 50 ) .1.3.6.1.4.1.1166.1.621.16.6.3 |
rserrorThis displays the Reed Solomon Errors.ro INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.16.6.4 |
lostlockcountThis displays the number of times tuner lost lock.ro INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.16.6.5 |
clearrserrorClears the rserror counter to zero.rw Enumeration .1.3.6.1.4.1.1166.1.621.16.6.6 |
clearlostlockcountClears the lostlockcount counter to zero.rw Enumeration .1.3.6.1.4.1.1166.1.621.16.6.7 |
snrThis displays the SNR value.ro INTEGER ( 0 .. 65535 ) .1.3.6.1.4.1.1166.1.621.16.6.8 |