CISCOSB-rlInterfaces
AI MIB Summary
The CISCOSB-rlInterfaces MIB module provides vendor-specific access to monitor and manage physical and logical interface states, traffic counters, and error statistics on Cisco Catalyst switches. It enables the retrieval of standard interface metrics such as octets, packets, discards, and errors to facilitate real-time link health assessment and troubleshooting within the Cisco IOS/IOS-XE environment.
The private MIB module definition for Switch Interfaces.
Main OID:
swInterfaces.1.3.6.1.4.1.9.6.1.101.43
99
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
99 total| Object Name |
|---|
swInterfacesThe private MIB module definition for Switch Interfaces. MODULE-IDENTITY .1.3.6.1.4.1.9.6.1.101.43 |
swIfTableSwitch media specific information and configuration of the device
interfaces. SEQUENCE OF SwIfEntry .1.3.6.1.4.1.9.6.1.101.43.1 |
swIfEntryDefines the contents of each line in the swIfTable table. SwIfEntry .1.3.6.1.4.1.9.6.1.101.43.1.1 |
swIfIndexIndex to the swIfTable. The interface defined by a
particular value of this index is the same interface as
identified by the same value of ifIndex (MIB II).ro INTEGER .1.3.6.1.4.1.9.6.1.101.43.1.1.1 |
swIfPhysAddressTypeThis variable indicates whether the physical address assigned to this
interface should be the default one or be chosen from the set of
reserved physical addresses of the device.rwobsolete Enumeration .1.3.6.1.4.1.9.6.1.101.43.1.1.2 |
swIfDuplexAdminModeThis variable specifies whether this interface should operate in
half duplex or full duplex mode. This specification will take effect
only if swIfSpeedDuplexAutoNegotiation is disabled.
A value of 'none' is returned if a value of the variable
hasn't been set.rw Enumeration .1.3.6.1.4.1.9.6.1.101.43.1.1.3 |
swIfDuplexOperModeThis variable indicates whether this interface operates in half
duplex or full duplex mode.
This variable can have the values hybrid or unknown
only for a trunk.
unknown - only if trunk operative status is not present.ro Enumeration .1.3.6.1.4.1.9.6.1.101.43.1.1.4 |
swIfBackPressureModeThis variable indicates whether this interface activates back pressure
when congested.rw Enumeration .1.3.6.1.4.1.9.6.1.101.43.1.1.5 |
swIfTaggedModeIf enable, this interface operates in tagged mode, i.e all frames sent
out through this interface will have the 802.1Q header.
If disabled the frames will not be tagged.rw Enumeration .1.3.6.1.4.1.9.6.1.101.43.1.1.6 |
swIfTransceiverTypeThis variable indicates the transceiver type of this interface.ro Enumeration .1.3.6.1.4.1.9.6.1.101.43.1.1.7 |
swIfLockAdminStatusThis variable indicates whether this interface should operate in locked
or unlocked mode.
In unlocked mode the device learns all MAC addresses from this port and
forwards all frames arrived at this port. In locked mode no new MAC
addresses are learned and only frames with known source MAC
addresses are forwarded.rw Enumeration .1.3.6.1.4.1.9.6.1.101.43.1.1.8 |
swIfLockOperStatusThis variable defines whether this interface operates in locked
or unlocked mode. It is locked in each of the following two cases:
1) if swLockAdminStatus is set to locked
2) no IP/IPX interface is defined over this interface and no
VLAN contains this interface.
In unlocked mode the device learns all MAC addresses from this port and
forwards all frames arrived at this port. In locked mode no new MAC
addresses are learned and only frames with known source MAC
addresses are forwarded.ro Enumeration .1.3.6.1.4.1.9.6.1.101.43.1.1.9 |
swIfTypeThis variable specifies the type of interface.ro Enumeration .1.3.6.1.4.1.9.6.1.101.43.1.1.10 |
swIfDefaultTagThis variable specifies the default VLAN tag which will be attached
to outgoing frames if swIfTaggedMode for this interface is enabled.ro INTEGER .1.3.6.1.4.1.9.6.1.101.43.1.1.11 |
swIfDefaultPriorityThis variable specifies the default port priority.rw INTEGER .1.3.6.1.4.1.9.6.1.101.43.1.1.12 |
swIfStatusThe status of a table entry.
It is used to delete an entry from this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.6.1.101.43.1.1.13 |
swIfFlowControlModeon - Flow control will be enabled on this interface according to the
IEEE 802.3x standard.
off - Flow control is disabled.
autoNegotiation - Flow control will be enabled or disabled on this
interface. If enabled, it will operate as specified
by the IEEE 802.3x standard.
enabledRx - Flow control will be enabled on this interface for
recieved frames.
enabledTx - Flow control will be enabled on this interface for
transmitted frames.
An attempt to set this object to 'enabledRx(4)' or 'enabledTx(5)'
will fail on interfaces that do not support operation
at greater than 100 Mb/s.
In any case, flow control can work only if swIfDuplexOperMode is
full.rw Enumeration .1.3.6.1.4.1.9.6.1.101.43.1.1.14 |
swIfSpeedAdminModeThis variable specifies the required speed of this interface in bits
per second. This specification will take effect only if
swIfSpeedDuplexAutoNegotiation is disabled.
A value of 10 is returned for 10G.
A value of 0 is returned if the value of the variable
hasn't been set.rw INTEGER .1.3.6.1.4.1.9.6.1.101.43.1.1.15 |
swIfSpeedDuplexAutoNegotiationIf enabled the speed and duplex mode will be set by the device through
the autonegotiation process. Otherwise these characteristics will be
set according to the values of swIfSpeedAdminMode and
swIfSpeedDuplexAutoNegotiation.rw Enumeration .1.3.6.1.4.1.9.6.1.101.43.1.1.16 |
swIfOperFlowControlModeon - Flow control is enabled on this interface according to the
IEEE 802.3x standard.
off - Flow control is disabled.
enabledRx - Flow control is enabled on this interface for
recieved frames.
enabledTx - Flow control is enabled on this interface for
transmitted frames.ro Enumeration .1.3.6.1.4.1.9.6.1.101.43.1.1.17 |
swIfOperSpeedDuplexAutoNegotiationIf enabled the speed and duplex are determined by the device through
the autonegotiation process.
If disabled these characteristics are determined according to the values
of swIfSpeedAdminMode and swIfDuplexAdminMode.
hybrid - only for a trunk.
unknown - only for ports that there operative status is not present.ro Enumeration .1.3.6.1.4.1.9.6.1.101.43.1.1.18 |
swIfOperBackPressureModeThis variable indicates the operative back pressure mode of
this interface.ro Enumeration .1.3.6.1.4.1.9.6.1.101.43.1.1.19 |
swIfAdminLockActionThis variable indicates which action this interface should be taken
in locked mode and therefore relevant only in locked mode.
Possible actions:
discard(1) - every packet is dropped.
forwardNormal(2) - every packet is forwarded according to the DST address.
discardDisable(3) - drops the first packet and suspends the port.rw Enumeration .1.3.6.1.4.1.9.6.1.101.43.1.1.20 |
swIfOperLockActionThis variable indicates which action this interface actually takes in
locked mode and therefore relevant only in locked mode.
Possible actions:
discard(1) - every packet is dropped.
forwardNormal(2) - every packet is forwarded according to the DST address.
discardDisable(3) - drops the first packet and suspends the port.ro Enumeration .1.3.6.1.4.1.9.6.1.101.43.1.1.21 |
swIfAdminLockTrapEnableThis variable indicates whether to create a SNMP trap in the locked mode.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.6.1.101.43.1.1.22 |
swIfOperLockTrapEnableThis variable indicates whether a SNMP trap can be created in the
locked mode.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.6.1.101.43.1.1.23 |
swIfOperSuspendedStatusThis variable indicates whether the port is suspended or not due to some
feature. After reboot this value is falsero TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.6.1.101.43.1.1.24 |
swIfLockOperTrapCountThis variable indicates the trap counter status per ifIndex
(i.e. number of received packets since the last trap sent due to a
packet which was received on this ifIndex). It's relevant only in locked
mode while trap is enabled.ro INTEGER (0 .. 2147483647 ) .1.3.6.1.4.1.9.6.1.101.43.1.1.25 |
swIfLockAdminTrapFrequencyThis variable indicates the minimal frequency (in seconds) of sending
a trap per ifIndex. It's relevant only in locked mode and in trap
enabled.rw INTEGER (1 .. 1000000) -- UNITS "seconds" .1.3.6.1.4.1.9.6.1.101.43.1.1.26 |
swIfReActivateThis variable reactivates (enables) an ifIndex (which was suspended)rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.6.1.101.43.1.1.27 |
swIfAdminMdixThe configuration is on a physical port, not include trunks.
cross - The interface should force crossover.
normal - The interface should not force crossover.
auto - Auto mdix is enabled on the interface.rw Enumeration .1.3.6.1.4.1.9.6.1.101.43.1.1.28 |
swIfOperMdixcross - The interface is in crossover mode.
normal - The interface is not in crossover mode.
unknown - Only for port that its operative status is not present
or down.ro Enumeration .1.3.6.1.4.1.9.6.1.101.43.1.1.29 |
swIfHostModeThis variable indicates the 802.1X host mode of a port. Relevant when the port's 802.1X control is auto.
In addtion multiple-auth was added.rw Enumeration .1.3.6.1.4.1.9.6.1.101.43.1.1.30 |
swIfSingleHostViolationAdminActionThis variable indicates which action this interface should take in single authorized.
Possible actions:
discard - every packet is dropped.
forwardNormal - every packet is forwarded according to the DST address.
discardDisable - drops the first packet and suspends the port.rw Enumeration .1.3.6.1.4.1.9.6.1.101.43.1.1.31 |
swIfSingleHostViolationOperActionThis variable indicates which action this interface actually takes in single authorized.
Possible actions:
discard(1) - every packet is dropped.
forwardNormal(2) - every packet is forwarded according to the DST address.
discardDisable(3) - drops the first packet and suspends the port.ro Enumeration .1.3.6.1.4.1.9.6.1.101.43.1.1.32 |
swIfSingleHostViolationAdminTrapEnableThis variable indicates whether to create a SNMP trap in single authorized.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.6.1.101.43.1.1.33 |
swIfSingleHostViolationOperTrapEnableThis variable indicates whether a SNMP trap can be created in the single authorized.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.6.1.101.43.1.1.34 |
swIfSingleHostViolationOperTrapCountThis variable indicates the trap counter status per ifIndex
(i.e. number of received packets since the last trap sent due to a packet
which was received on this ifIndex). It's relevant only in single authorized
while trap is enabled.ro INTEGER (0 .. 2147483647) .1.3.6.1.4.1.9.6.1.101.43.1.1.35 |
swIfSingleHostViolationAdminTrapFrequencyThis variable indicates the minimal frequency (in seconds) of sending a
trap per ifIndex. It's relevant only in single authorized and in trap enabled.
A value of 0 means that trap is disabled.rw INTEGER (0 .. 1000000) -- UNITS "seconds" .1.3.6.1.4.1.9.6.1.101.43.1.1.36 |
swIfLockLimitationModeThis variable indicates what is the learning limitation on the locked interface.
Possible values:
disabled - learning is stopped. The dynamic addresses associated with the
port are not aged out or relearned on other port as long as the port is
locked.
dynamic - dynamic addresses can be learned up to the maximum dynamic addresses
allowed on the port. Relearning and aging of the dynamic addresses are
enabled. The learned addresses aren't kept after reset.
secure-permanent - secure addresses can be learned up to the maximum addresses
allowed on the port. Relearning and aging of addresses are disabled.
The learned addresses are kept after reset.
secure-delete-on-reset - secure addresses can be learned up to the maximum addresses
allowed on the port. Relearning and aging of addresses are disabled.
The learned addresses are not kept after reset.rw Enumeration .1.3.6.1.4.1.9.6.1.101.43.1.1.37 |
swIfLockMaxMacAddressesThis variable defines the maximum number of dynamic addresses that
can be asscoiated with the locked interface. It isn't relevant in
disabled limitation mode.rw INTEGER (0 .. 2147483647) .1.3.6.1.4.1.9.6.1.101.43.1.1.38 |
swIfLockMacAddressesCountThis variable indicates the actual number of dynamic addresses that can
be asscoiated with the locked interface. It isn't relevant in disabled
limitation mode.ro INTEGER (0 .. 2147483647) .1.3.6.1.4.1.9.6.1.101.43.1.1.39 |
swIfAdminSpeedDuplexAutoNegotiationLocalCapabilitiesAdministrative auto negotiation capabilities of the interface that can be advertised when
swIfSpeedDuplexAutoNegotiation is enabled.
default bit means advertise all the port's capabilities
according to its type.rw AutoNegCapabilitiesBits .1.3.6.1.4.1.9.6.1.101.43.1.1.40 |
swIfOperSpeedDuplexAutoNegotiationLocalCapabilitiesOperative auto negotiation capabilities of the remote link.
unknown bit means that port operative status is not up.ro AutoNegCapabilitiesBits .1.3.6.1.4.1.9.6.1.101.43.1.1.41 |
swIfSpeedDuplexNegotiationRemoteCapabilitiesOperative auto negotiation capabilities of the remote link.
unknown bit means that port operative status is not up,
or auto negotiation process not complete,
or remote link is not auto negotiation able.ro AutoNegCapabilitiesBits .1.3.6.1.4.1.9.6.1.101.43.1.1.42 |
swIfAdminComboModeThis variable specifies the administrative mode of a combo Ethernet interface.rw Enumeration .1.3.6.1.4.1.9.6.1.101.43.1.1.43 |
swIfOperComboModeThis variable specifies the operative mode of a combo Ethernet interface.ro Enumeration .1.3.6.1.4.1.9.6.1.101.43.1.1.44 |
swIfAutoNegotiationMasterSlavePreferenceThis variable specifies the administrative mode of the Maste-Slave preference in auto negotiation.rw Enumeration .1.3.6.1.4.1.9.6.1.101.43.1.1.45 |
swIfMibVersionThe swIfTable Mib's version, the current version is 3.ro INTEGER .1.3.6.1.4.1.9.6.1.101.43.2 |
swIfPortLockSupportindicates if the locked port package is supported.ro Enumeration .1.3.6.1.4.1.9.6.1.101.43.3 |
swIfPortLockActionSupportindicates which port lock actions are supported:
(bit 0 is the most significant bit)
bit 0 - discard
bit 1 - forwardNormal
bit 2 - discardDisablero OCTET STRING .1.3.6.1.4.1.9.6.1.101.43.4 |
swIfPortLockTrapSupportindicates with which port lock actions the trap option is supported
(e.g. discard indicates that trap is supported only when the portlock
action is discard):
(bit 0 is the most significant bit)
bit 0 - discard
bit 1 - forwardNormal
bit 2 - discardDisablero OCTET STRING .1.3.6.1.4.1.9.6.1.101.43.5 |
swIfPortLockIfRangeTablePort lock interfaces range configuration SEQUENCE OF SwIfPortLockIfRangeEntry .1.3.6.1.4.1.9.6.1.101.43.6 |
swIfPortLockIfRangeEntryDefines the contents of each line in the swIfPortLockIfRangeTable table. SwIfPortLockIfRangeEntry .1.3.6.1.4.1.9.6.1.101.43.6.1 |
swIfPortLockIfRangeIndexIndex to the swIfPortLockIfRangeTable.ro INTEGER .1.3.6.1.4.1.9.6.1.101.43.6.1.1 |
swIfPortLockIfRangeThe set of interfaces to which the port lock parameters should be configuredrw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.9.6.1.101.43.6.1.2 |
swIfPortLockIfRangeLockStatusThis variable indicates whether the interfaces range should operate in locked
or unlocked mode.
In unlocked mode the device learns all MAC addresses from these interfaces and
forwards all frames arrived at these interfaces. In locked mode no new MAC
addresses are learned and only frames with known source MAC
addresses are forwarded.rw Enumeration .1.3.6.1.4.1.9.6.1.101.43.6.1.3 |
swIfPortLockIfRangeActionThis variable indicates which action for these interfaces should be take
in locked mode and therefore relevant only in locked mode.
Possible actions:
discard(1) - every packet is dropped.
forwardNormal(2) - every packet is forwarded according to the DST address.
discardDisable(3) - drops the first packet and suspends the port.rw Enumeration .1.3.6.1.4.1.9.6.1.101.43.6.1.4 |
swIfPortLockIfRangeTrapEnThis variable indicates whether to create a SNMP trap in the locked mode.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.6.1.101.43.6.1.5 |
swIfPortLockIfRangeTrapFreqThis variable indicates the minimal frequency (in seconds) of sending
a trap for these interfaces. It's relevant only in locked mode and in trap
enabled.rw INTEGER (1 .. 1000000) -- UNITS "seconds" .1.3.6.1.4.1.9.6.1.101.43.6.1.6 |
swIfExtTableDisplay information and configuration of the device interfaces. SEQUENCE OF SwIfExtEntry .1.3.6.1.4.1.9.6.1.101.43.7 |
swIfExtEntryDefines the contents of each row in the swIfExtTable. SwIfExtEntry .1.3.6.1.4.1.9.6.1.101.43.7.1 |
swIfExtSFPSpeedConfigure speed of an SFP Ethernet interface.rw Enumeration .1.3.6.1.4.1.9.6.1.101.43.7.1.1 |
rlIfMibVersionMIB's version, the current version is 1.ro INTEGER .1.3.6.1.4.1.89.54.1 |
rlIfNumOfPhPortsTotal number of physical ports on this device
(including all stack units)ro INTEGER .1.3.6.1.4.1.89.54.2 |
rlIfMapOfOnPhPortsEach bit in this octet string indicates that the correspondig port's
ifOperStatus is ON if set.
The mapping of port number to bits in this octet string is as follows:
The port with the L2 interface number 1 is mapped to the least
significant bit of the 1st octet, the port with L2 ifNumber 2 to the
next significant bit in the 1st octet, port 8 to the most-significant
bit of the in the 1st octet, port 9 to the least
significant bit of the 2nd octet, etc. and in general,
port n to bit corresponding to 2**((n mod 8) -1) in byte n/8 + 1ro OCTET STRING .1.3.6.1.4.1.89.54.3 |
rlIfClearPortMibCountersEach bit that is set in this portList represent a port that
its mib counters should be reset.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.89.54.4 |
rlIfNumOfUserDefinedPortsThe number of user defined ports on this device.ro INTEGER .1.3.6.1.4.1.89.54.5 |
rlIfFirstOutOfBandIfIndexFirst ifIndex of out-of-band port.
This scalar exists only the device has out of band ports.ro INTEGER .1.3.6.1.4.1.89.54.6 |
rlIfNumOfLoopbackPortsThe number of loopback ports on this device.ro INTEGER .1.3.6.1.4.1.89.54.7 |
rlIfFirstLoopbackIfIndexFirst ifIndex of loopback port.
This scalar will exists only if rlIfNumOfLoopbackPorts
is different from 0.ro INTEGER .1.3.6.1.4.1.89.54.8 |
rlIfExistingPortListIndicates which ports/trunks exist in the system.
It doesn't indicate which are present.ro PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.89.54.9 |
rlIfBaseMACAddressPerIfIndexIndicates if the system will assign a unique MAC per Ethernet port or not.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.54.10 |
rlFlowControlCascadeModeenable disable flow control on cascade portsrw Enumeration .1.3.6.1.4.1.89.54.11 |
rlFlowControlCascadeTypedefine which type of ports will be affected by flow control on cascade portsrw Enumeration .1.3.6.1.4.1.89.54.12 |
rlFlowControlRxPerSystemdefine if flow control RX is supported per system.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.54.13 |
rlCascadePortProtectionActionAs a result of this set all of the local cascade ports
will stop being consider unstable and will be force up.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.54.14 |
rlManagementIfIndexSpecify L2 bound management interface index in a single IP address system
when configurable management interface is supported.rw InterfaceIndex (IF-MIB) .1.3.6.1.4.1.89.54.15 |
rlIfClearStackPortsCountersAs a result of this set all counters of
all external cascade ports will be cleared.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.54.16 |
rlIfClearPortMacAddressesif port is non secure, its all dynamic MAC addresses are cleared.
if port is secure, its all secure MAC addresses which have learned or configured are cleared.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.89.54.17 |
rlIfCutThroughPacketLengthThe default packet length that is assigned to a packet in the
Cut-Through mode.rw INTEGER (257 .. 16383) .1.3.6.1.4.1.89.54.18 |
rlIfCutPriorityZeroEnable or disable cut-Through for priority 0.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.54.19 |
rlIfCutPriorityOneEnable or disable cut-Through for priority 1.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.54.20 |
rlIfCutPriorityTwoEnable or disable cut-Through for priority 2.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.54.21 |
rlIfCutPriorityThreeEnable or disable cut-Through for priority 3.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.54.22 |
rlIfCutPriorityFourEnable or disable cut-Through for priority 4.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.54.23 |
rlIfCutPriorityFiveEnable or disable cut-Through for priority 5.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.54.24 |
rlIfCutPrioritySixEnable or disable cut-Through for priority 6.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.54.25 |
rlIfCutPrioritySevenEnable or disable cut-Through for priority 7.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.54.26 |
rlIfCutThroughTableInformation and configuration of cut-through feature. SEQUENCE OF RlIfCutThroughEntry .1.3.6.1.4.1.89.54.27 |
rlIfCutThroughEntryDefines the contents of each line in the swIfTable table. RlIfCutThroughEntry .1.3.6.1.4.1.89.54.27.1 |
rlIfCutThroughPriorityEnableEnable or disable cut-through for a priority for an interface.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.54.27.1.1 |
rlIfCutThroughUntaggedEnableEnable or disable cut-through for untagged packets for an interface.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.54.27.1.2 |
rlIfCutThroughOperModeOperational mode of spesific cut-through interface.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.54.27.1.3 |
rlCutThroughPacketLengthThe default packet length that is assigned to a packet in the
Cut-Through mode.ro INTEGER .1.3.6.1.4.1.89.54.28 |
rlCutThroughPacketLengthAfterResetThe default packet length that is assigned to a packet in the
Cut-Through mode after reset.rw INTEGER (257 .. 16383) .1.3.6.1.4.1.89.54.29 |
rlCutThroughEnableCut-Through global enable mode.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.54.30 |
rlCutThroughEnableAfterResetCut-Through global enable mode after reset.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.54.31 |
rlFlowControlModeDefine which mode will be enabled on flow control enabled ports.
The interfaces with enabled flow control will receive pause frames, but will not send flow control pause
frames
Send-receive: The interfaces with enabled flow control will receive and send pause frames.
Receive-only: The interfaces with enabled flow control will receive pause frames, but will not send flow
control pause frames.rw Enumeration .1.3.6.1.4.1.89.54.32 |