CISCO-WDS-INFO-MIB
AI MIB Summary
The CISCO-WDS-INFO-MIB monitors Wireless Domain Services (WDS) entities on Cisco infrastructure to track Layer 3 roaming states, CCKM authentication sessions, and mobility bindings between Access Points, Mobile Nodes, and the Wireless LAN Services Module (WLSM). It provides visibility into WDS registration status, mGRE tunnel topology, and roaming patterns to facilitate seamless client mobility across different IP subnets.
This MIB is intended to be implemented on all Cisco network entities that provide Wireless Domain Services (WDS). The WDS provides a control mechanism for wireless devices that roam between Access Points residing on different layer 3 subnets. When WDS is in the Wireless LAN Services Module(WLSM), the access points providing Layer 3 mobility must register with the WDS before wireless devices are given access to the mobility network. The location of the WDS is specified in each Access Point along with LEAP device credentials that are required for authentication with the WDS. Once the Access Point and the Mobile Node are authenticated with the WDS, those are considered registered.
This MIB reports the information about the Wireless Domain Servers, Access Points, Mobile Nodes, and their roaming patterns.
GLOSSARY AAA
Authentication, Authorization, Accounting
Access Point (AP)
An entity that contains an 802.11 medium access control (MAC) and physical layer (PHY) interface and provides access to the distribution services via the wireless medium for associated devices.
BSSID
Basic Service Set Identification, where the basic service set is defined as the set of data transfer rates that all the stations in a BSS will be capable of using to receive frames from the wireless medium.
CCKM
Cisco Central Key Management.
Context
The mobility context for a Mobile Node includes its current mobility bindings with the Access Points, IP/802 address bindings, cached configuration parameters, QoS state, IP group membership, authentication state, accounting statistics, and other dynamically derived protocol state information.
EAP
Extensible Authentication Protocol.
Hot Standby Router Protocol (HSRP)
Cisco Hot Standby Router Protocol as defined in RFC2281
L3MM
Layer-3 Mobility Manager (L3MM) is a new software entity residing on Central Switch (CS). L3MM maintains the mobility database and manages mGRE tunnels and tunnel paths to provide L3 Mobility for wireless clients.
Layer 3 Mobility Control Protocol (LCP)
A simple protocol to exchange control message between WDS and L3MM to achieve layer 3 seamless mobility for wireless devices.
mGRE Tunnels
Multipoint Generic Routing Encapsulation tunnels. This tunnel is used to tunnel wireless traffic and used to transfer wireless traffic between AP and CS.
MIC
Message Integrity Check. A MIC can, optionally, be added to WEP-encrypted 802.11 frames.
Mobile Node (MN)
A roaming 802.11 wireless device in a wireless network associated with an Access Point.
SSID
Service Set Identification, where the station service is defined as the set of services that support transport of medium access control (MAC) service data units (MSDUs) between stations within a basic service set.
TKIP
WPA Temporal Key encryption.
Wireless Domain Services (WDS)
The set of services being offered at a particular broadcast domain that may be an IP subnet or a particular VLAN, or across the L3 cloud. The services include the following.
1. Fast Secure Roaming with CCKM.
2. Layer 3 seamless mobility.
3. Radio Management aggregation for 802.11 wireless
clients .
WDS Entity
The logical entity that resides in an infrastructure node and offers WDS to the descendants of that infrastructure node in the wireless services hierarchy.
WEP
Wired Equivalent Privacy. This is generally used to refer to 802.11 legacy encryption.
WLSM
Wireless LAN Services Module
Wireless Network Manager (WNM)
The network management system that manages the entire hierarchy of devices providing WDS.
WPA
WiFi Protected Access.
Main OID:
ciscoWdsInfoMIB.1.3.6.1.4.1.9.9.509
108
Objects
Active
Status
8
Dependencies
Imported Objects
Objects
108 total| Object Name |
|---|
ciscoWdsInfoMIBThis MIB is intended to be implemented on all Cisco
network entities that provide Wireless Domain Services
(WDS). The WDS provides a control mechanism for
wireless devices that roam between Access Points
residing on different layer 3 subnets. When WDS is in
the Wireless LAN Services Module(WLSM), the access
points providing Layer 3 mobility must register with
the WDS before wireless devices are given access to the
mobility network. The location of the WDS is specified
in each Access Point along with LEAP device credentials
that are required for authentication with the WDS. Once
the Access Point and the Mobile Node are authenticated
with the WDS, those are considered registered.
This MIB reports the information about the Wireless
Domain Servers, Access Points, Mobile Nodes, and their
roaming patterns.
GLOSSARY
AAA
Authentication, Authorization, Accounting
Access Point (AP)
An entity that contains an 802.11 medium access
control (MAC) and physical layer (PHY) interface
and provides access to the distribution services via
the wireless medium for associated devices.
BSSID
Basic Service Set Identification, where the basic
service set is defined as the set of data transfer
rates that all the stations in a BSS will be capable
of using to receive frames from the wireless medium.
CCKM
Cisco Central Key Management.
Context
The mobility context for a Mobile Node includes its
current mobility bindings with the Access Points,
IP/802 address bindings, cached configuration
parameters, QoS state, IP group membership,
authentication state, accounting statistics, and
other dynamically derived protocol state information.
EAP
Extensible Authentication Protocol.
Hot Standby Router Protocol (HSRP)
Cisco Hot Standby Router Protocol as defined in RFC2281
L3MM
Layer-3 Mobility Manager (L3MM) is a new software
entity residing on Central Switch (CS). L3MM maintains
the mobility database and manages mGRE tunnels and
tunnel paths to provide L3 Mobility for wireless
clients.
Layer 3 Mobility Control Protocol (LCP)
A simple protocol to exchange control message between
WDS and L3MM to achieve layer 3 seamless mobility for
wireless devices.
mGRE Tunnels
Multipoint Generic Routing Encapsulation tunnels. This
tunnel is used to tunnel wireless traffic and used to
transfer wireless traffic between AP and CS.
MIC
Message Integrity Check. A MIC can, optionally,
be added to WEP-encrypted 802.11 frames.
Mobile Node (MN)
A roaming 802.11 wireless device in a wireless
network associated with an Access Point.
SSID
Service Set Identification, where the station service
is defined as the set of services that support
transport of medium access control (MAC) service data
units (MSDUs) between stations within a basic service
set.
TKIP
WPA Temporal Key encryption.
Wireless Domain Services (WDS)
The set of services being offered at a particular
broadcast domain that may be an IP subnet or a
particular VLAN, or across the L3 cloud. The services
include the following.
1. Fast Secure Roaming with CCKM.
2. Layer 3 seamless mobility.
3. Radio Management aggregation for 802.11 wireless
clients .
WDS Entity
The logical entity that resides in an infrastructure
node and offers WDS to the descendants of that
infrastructure node in the wireless services
hierarchy.
WEP
Wired Equivalent Privacy. This is generally used
to refer to 802.11 legacy encryption.
WLSM
Wireless LAN Services Module
Wireless Network Manager (WNM)
The network management system that manages the
entire hierarchy of devices providing WDS.
WPA
WiFi Protected Access. MODULE-IDENTITY .1.3.6.1.4.1.9.9.509 |
ciscoWdsInfoMIBNotifs OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.509.0 |
cwdsiLcpStatusChangeThis notification will be sent when a LCP status
changes from 'down' to 'up' or from 'up' to 'down'. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.509.0.1 |
cwdsiHsrpStateChangeThis notification will be sent when HSRP state
changes from 'standby' to 'active' or from 'active' to
'standby'. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.509.0.2 |
ciscoWdsInfoMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.509.1 |
ciscoWdsInfoMacAuthCache OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.509.1.1 |
cwdsiMacAuthCacheTableThis table provides the information about the MAC
addresses cached in the WDS for MAC authentication.
MAC authentication caching reduces overhead because
the WDS authenticates devices in its MAC-address
cache without sending the request to the
authentication server.
An entry is added to this table when a Mobile Node
completes MAC authentication to the authentication
server. An entry is removed if the MAC address is not
flushed before timeout. SEQUENCE OF CwdsiMacAuthCacheEntry .1.3.6.1.4.1.9.9.509.1.1.1 |
cwdsiMacAuthCacheEntryEach entry is a set of a MAC address and age for
fast MAC authentication. CwdsiMacAuthCacheEntry .1.3.6.1.4.1.9.9.509.1.1.1.1 |
cwdsiMacAuthCacheMacAddrThis object specifies the MAC address of the device
which is cached in the WDS for MAC authentication. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.9.9.509.1.1.1.1.1 |
cwdsiMacAuthCacheAgeThis object specifies the elapsed time since the MAC
address has been cached. If the MAC address is not
flushed within the specific time(default 30 minutes),
the entry with cwdsiMacAuthCacheMacAddr is removed.ro Unsigned32 UNITS "minutes" .1.3.6.1.4.1.9.9.509.1.1.1.1.2 |
ciscoWdsInfoAccessPoint OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.509.1.2 |
cwdsiApTableThis table provides the information about the Access
Points registered with WDS.
An entry is added to this table when a Access Point
register with WDS and the entry is removed after the
lifetime of the Access Point expires. SEQUENCE OF CwdsiApEntry .1.3.6.1.4.1.9.9.509.1.2.1 |
cwdsiApEntryEach entry is a set of attributes of an Access Point
currently registered with WDS. CwdsiApEntry .1.3.6.1.4.1.9.9.509.1.2.1.1 |
cwdsiApMacAddrThe MAC address of the Access Point. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.9.9.509.1.2.1.1.1 |
cwdsiApAddrTypeRepresents the type of Internet address stored in the
corresponding instance of the cwdsiApAddr.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.509.1.2.1.1.2 |
cwdsiApAddrThe Internet address of the Access Point.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.509.1.2.1.1.3 |
cwdsiApNameThis object specifies the hostname of the Access
Point.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.509.1.2.1.1.4 |
cwdsiApStateThis object specifies the registration state of the
Access Point with the WDS.ro CWdsDeviceState .1.3.6.1.4.1.9.9.509.1.2.1.1.5 |
cwdsiApLifeTimeThis object specifies the maximum time after which
the registration of the Access Point with WDS expires.
The Access Point must re-register before the lifetime
is exhausted, otherwise it will be deleted from the
table.ro Unsigned32 UNITS "seconds" .1.3.6.1.4.1.9.9.509.1.2.1.1.6 |
cwdsiApNeighborAddrTypeRepresents the type of Internet address stored in the
corresponding instance of the cwdsiApNeighborAddr.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.509.1.2.1.1.7 |
cwdsiApNeighborAddrThe Internet address of the network entity with which
the Ethernet port of the Access Point is directly
connected.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.509.1.2.1.1.8 |
cwdsiApNeighborNameThis object specifies the hostname of the network
entity with which the Ethernet port of the Access Point
is directly connected.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.509.1.2.1.1.9 |
cwdsiApNeighborPortNameThis object specifies the port name of the network
entity with which the Ethernet port of the Access Point
is directly connected. This will typically be the value
of the ifName object (e.g., 'Ethernet0').ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.509.1.2.1.1.10 |
ciscoWdsInfoMobileNode OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.509.1.3 |
cwdsiMnTableThis table provides the information about the Mobile
Nodes registered with WDS.
An entry is added to this table when a Mobile Node
registers with WDS and the entry is removed after the
lifetime of the Mobile Node expires. SEQUENCE OF CwdsiMnEntry .1.3.6.1.4.1.9.9.509.1.3.1 |
cwdsiMnEntryEach entry is a set of attributes of a Mobile Node
currently registered with WDS. CwdsiMnEntry .1.3.6.1.4.1.9.9.509.1.3.1.1 |
cwdsiMnMacAddrThe MAC address of the Mobile Node. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.9.9.509.1.3.1.1.1 |
cwdsiMnAddrTypeRepresents the type of Internet address stored in the
corresponding instance of the cwdsiMnAddr.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.509.1.3.1.1.2 |
cwdsiMnAddrThe Internet address of the Mobile Node.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.509.1.3.1.1.3 |
cwdsiMnApMacAddrThe MAC address of the Access Point with which the
Mobile Node is associated.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.9.9.509.1.3.1.1.4 |
cwdsiMnApAddrTypeRepresents the type of Internet address stored in the
corresponding instance of the cwdsiMnApAddr.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.509.1.3.1.1.5 |
cwdsiMnApAddrThe Internet address of the Access Point with which
the Mobile Node has associated.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.509.1.3.1.1.6 |
cwdsiMnMobilityNetworkIdThis object specifies the mobility network-id of the
Mobile Node.ro Unsigned32 .1.3.6.1.4.1.9.9.509.1.3.1.1.7 |
cwdsiMnStateThis object specifies the registration state of the
Mobile Node with WDS.ro CWdsDeviceState .1.3.6.1.4.1.9.9.509.1.3.1.1.8 |
cwdsiMnSsidThis object specifies the SSID with which the Mobile
Node has associated with the Access Point.ro CDot11SsidString (CISCO-DOT11-SSID-SECURITY-MIB) .1.3.6.1.4.1.9.9.509.1.3.1.1.9 |
cwdsiMnBssidThis object specifies the BSSID used by the Mobile
Node to communicate with the Access Point.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.9.9.509.1.3.1.1.10 |
cwdsiMnVlanThis object specifies the VLAN ID used by Access Point
to bridge trunk that carries the traffic, when the
Mobile Node associates with Access Point specified by
cwdsiMnApAddr, using SSID specified by cwdsiMnSsid.ro CDot11IfVlanIdOrZero (CISCO-DOT11-IF-MIB) .1.3.6.1.4.1.9.9.509.1.3.1.1.11 |
cwdsiMnKeyMgmtThis object specifies the type of authenticated key
management. If none of the bit is set, no key
management is used.ro CDot11SecAuthKeyMgmtType (CISCO-DOT11-SSID-SECURITY-MIB) .1.3.6.1.4.1.9.9.509.1.3.1.1.12 |
cwdsiMnAuthTypeThis object specifies one of the pre-defined
authentication algorithms and additional
authentication procedures for the Mobile Node.
When the cwdsiMnState is 'registered', the valid
combination of the authentications are:
- open(0),
- shared(1),
- leap(2),
- eap(3),
- mac(4),
- open(0) and eap(3),
- open(0) and mac(4),
- open(0), eap(3) and mac(4),
- open(0) and macOrEap(5),
- shared(1) and eap(3),
- shared(1) and mac(4),
- shared(1), eap(3) and mac(4),
- mac(4) and leap(2).
Otherwise, the valid combination of the
authentications are:
- eap(3),
- mac(4),
- eap(3) and mac(4),
- macOrEap(5),
- leap(2),
- mac(4) and leap(2),
- macOrLeap(6),
- eapOptional(7).
If none of the bits are set, there is no run-time
authentication.ro CWdsDeviceAuthType .1.3.6.1.4.1.9.9.509.1.3.1.1.13 |
cwdsiMnUptimeThis object specifies the value of sysUpTime at the
time this Mobile Node registered with WDS.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.9.9.509.1.3.1.1.14 |
cwdsiMnLifetimeThis object specifies the maximum time after which the
registration of the Mobile Node with its WDS expires.
The Mobile Node must re-register before the time
expires, otherwise it will be deleted from the table.ro Unsigned32 UNITS "seconds" .1.3.6.1.4.1.9.9.509.1.3.1.1.15 |
ciscoWdsInfoNetworkManager OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.509.1.4 |
cwdsiWnmTableThis table provides the information about the Wireless
Network Managers configured on WDS. WDS provides an
aggregation point of all radio management traffic from
participating Access Points to the registered Wireless
Network Manager. The entry also provides the statistics
between WDS and Wireless Network Manager.
An entry is added to this table when a Wireless Network
Manager is configured on WDS. Currently WDS supports
just one Wireless Network Manger. SEQUENCE OF CwdsiWnmEntry .1.3.6.1.4.1.9.9.509.1.4.1 |
cwdsiWnmEntryEach entry is a set of attributes of a Wireless
Network Manger and statistics.
The statistics is gathered since the Wireless
Network Manager has been registered with WDS. CwdsiWnmEntry .1.3.6.1.4.1.9.9.509.1.4.1.1 |
cwdsiWnmAddrTypeRepresents the type of Internet address stored in the
corresponding instance of the cwdsiWnmAddr. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.509.1.4.1.1.1 |
cwdsiWnmAddrThe Internet address of the Wireless Network Manager. InetAddress .1.3.6.1.4.1.9.9.509.1.4.1.1.2 |
cwdsiWnmStateThis object specifies the registration state of the
Wireless Network Manger with WDS.ro CWdsDeviceState .1.3.6.1.4.1.9.9.509.1.4.1.1.3 |
cwdsiWnmLinkStatusThis object specifies the link status between WDS and
Wireless Network Manager.ro Enumeration .1.3.6.1.4.1.9.9.509.1.4.1.1.4 |
cwdsiWnmClientTrackingThis object specifies the status of Client Tracking on
WDS.ro CWdsClientTrackingStatus .1.3.6.1.4.1.9.9.509.1.4.1.1.5 |
cwdsiWnmReqMsgCountThis object specifies the number of messages that are
supposed to be sent to Wireless Network Manger.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS, and at other times as
indicated by the value of cwdsiWnmDiscontinuityTime.ro Counter32 .1.3.6.1.4.1.9.9.509.1.4.1.1.6 |
cwdsiWnmSentMsgCountThis object specifies the number of sent messages by
WDS to Network Manger.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS, and at other times as
indicated by the value of cwdsiWnmDiscontinuityTime.ro Counter32 .1.3.6.1.4.1.9.9.509.1.4.1.1.7 |
cwdsiWnmRetryTxMsgCountThis object specifies the number of transmitted
messages by WDS to Network Manger after more than one
retransmission.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS, and at other times as
indicated by the value of cwdsiWnmDiscontinuityTime.ro Counter32 .1.3.6.1.4.1.9.9.509.1.4.1.1.8 |
cwdsiWnmWaitingAckMsgCountThis object specifies the number of sent messages by
WDS and waiting for acknowledge response from Wireless
Network Manger.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS, and at other times as
indicated by the value of cwdsiWnmDiscontinuityTime.ro Counter32 .1.3.6.1.4.1.9.9.509.1.4.1.1.9 |
cwdsiWnmDropMicTxMsgCountThis object specifies the number of dropped messages
by WDS because of Message Integrity Check (MIC) failure
before sending the messages to Wireless Network
Manger.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS, and at other times as
indicated by the value of cwdsiWnmDiscontinuityTime.ro Counter32 .1.3.6.1.4.1.9.9.509.1.4.1.1.10 |
cwdsiWnmDropUmdTxMsgCountThis object specifies the number of dropped messages
by WDS because of the Unacknowledged Message
Descriptor (UMD) allocation problem before sending the
messages to Wireless Network Manger.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS, and at other times as
indicated by the value of cwdsiWnmDiscontinuityTime.ro Counter32 .1.3.6.1.4.1.9.9.509.1.4.1.1.11 |
cwdsiWnmIndicatedMsgCountThis object specifies the number of indicated messages
to WDS before receiving the messages from Wireless
Network Manager.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS, and at other times as
indicated by the value of cwdsiWnmDiscontinuityTime.ro Counter32 .1.3.6.1.4.1.9.9.509.1.4.1.1.12 |
cwdsiWnmRxMsgCountThis object specifies the number of received messages
by WDS after receiving the messages from Wireless
Network Manager.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS, and at other times as
indicated by the value of cwdsiWnmDiscontinuityTime.ro Counter32 .1.3.6.1.4.1.9.9.509.1.4.1.1.13 |
cwdsiWnmDropRxMsgCountThis object specifies the number of messages dropped
by WDS received from Wireless Network Manager.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS, and at other times as
indicated by the value of cwdsiWnmDiscontinuityTime.ro Counter32 .1.3.6.1.4.1.9.9.509.1.4.1.1.14 |
cwdsiWnmDiscontinuityTimeThis object specifies the vaule of sysUpTime on the
most recent occassion when the WNM is registered with
WDS.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.9.9.509.1.4.1.1.15 |
ciscoWdsInfoStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.509.1.5 |
cwdsiApNumThis object specifies the number of Access Points
currently registered with this WDS.ro Gauge32 UNITS "access-points" .1.3.6.1.4.1.9.9.509.1.5.1 |
cwdsiMnNumThis object specifies the number of Mobile Nodes
currently registered with this WDS.ro Gauge32 UNITS "mobile-nodes" .1.3.6.1.4.1.9.9.509.1.5.2 |
cwdsiAaaAuthAttemptCountThis object specifies the number of AAA authentication
attempts (such as LEAP) made by WDS to authenticate
Access Points and Mobile Nodes.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS.ro Counter32 .1.3.6.1.4.1.9.9.509.1.5.3 |
cwdsiAaaAuthSuccessCountThis object specifies the number of successful AAA
authentication successes made by WDS to authenticate
Access Points and Mobile Nodes.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS.ro Counter32 .1.3.6.1.4.1.9.9.509.1.5.4 |
cwdsiAaaAuthFailureCountThis object specifies the number of failed AAA
authentication attempts made by WDS to authenticate
Access Points and Mobile Nodes.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS.ro Counter32 .1.3.6.1.4.1.9.9.509.1.5.5 |
cwdsiMacSpoofingBlockCountThis object specifies the number of MAC Spoofing
attempts detected and blocked by WDS.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS.ro Counter32 .1.3.6.1.4.1.9.9.509.1.5.6 |
cwdsiRoamsWithoutAaaAuthCountThis object specifies the number of roams not
involving AAA authentication.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS.ro Counter32 .1.3.6.1.4.1.9.9.509.1.5.7 |
cwdsiRoamsWithFullAaaAuthCountThis object specifies the number of roams involving
full AAA authentication.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS.ro Counter32 .1.3.6.1.4.1.9.9.509.1.5.8 |
cwdsiRoamsFastSecuredCountThis object specifies the number of fast and secured
roams with CCKM.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS.ro Counter32 .1.3.6.1.4.1.9.9.509.1.5.9 |
cwdsiMscMismatchCountThis object specifies the number of Message Sequence
Counter (MSC) mismatches.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS.ro Counter32 .1.3.6.1.4.1.9.9.509.1.5.10 |
cwdsiKscFailureCountThis object specifies the number of failures for Key
Sequence (KSC) with which WDS authenticates the Mobile
Node for Fast Secure Roaming.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS.ro Counter32 .1.3.6.1.4.1.9.9.509.1.5.11 |
cwdsiMicFailureCountThis object specifies the number of Message Integrity
Check (MIC) failures detected by WDS.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS.ro Counter32 .1.3.6.1.4.1.9.9.509.1.5.12 |
cwdsiRnMismatchCountThis object specifies the number of mismatches for
ReKey Number (RN) with which WDS authenticates the
Mobile Node for Fast Secure Roaming.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS.ro Counter32 .1.3.6.1.4.1.9.9.509.1.5.13 |
ciscoWdsInfoMobility OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.509.1.6 |
cwdsiLcpStatusThis object indicates the LCP link status. LCP is a
communication protocol between WDS residing on WLSM and
L3MM on RP to provide L3MM with up-to-date information
about current location of Mobile Node and also to
propagate tunnel end point and other configuration
information from RP to WDS/AP.
down(1) - The LCP link status is down,
up(2) - The LCP link status is up,
inTransition(3) - The LCP link status is in
transition from up(2) to down(1)
or from down(1) to up(2).ro Enumeration .1.3.6.1.4.1.9.9.509.1.6.1 |
cwdsiCsMgmtAddrTypeRepresents the type of Internet address stored in the
corresponding instance of the cwdsiCsMgmtAddr.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.509.1.6.2 |
cwdsiCsMgmtAddrThe Internet address of the Central Switch
Management.ro InetAddress .1.3.6.1.4.1.9.9.509.1.6.3 |
cwdsiWdsAddrTypeRepresents the type of Internet address stored in the
corresponding instance of the cwdsiWdsAddr.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.509.1.6.4 |
cwdsiWdsAddrThe Internet address of the network device in which
WDS resides.ro InetAddress .1.3.6.1.4.1.9.9.509.1.6.5 |
cwdsiWdsHsrpVirtualAddrTypeRepresents the type of Internet address stored in the
corresponding instance of the cwdsiWdsHsrpVirtualAddr.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.509.1.6.6 |
cwdsiWdsHsrpVirtualAddrThe vitrual Internet address of the WLSM when the HSRP
is enabled.ro InetAddress .1.3.6.1.4.1.9.9.509.1.6.7 |
cwdsiHsrpStateThis object indicates the state of HSRP.
unknown(1) - The state is unknown.
disabled(2) - The HSRP is disabled.
initial(3) - This is the starting state and
indicates that HSRP is not running.
learn(4) - The router is still waiting to hear
from the active router.
backup(5) - The router monitors the availability
and state of the Master Router.
speak(6) - The router sends periodic Hello
messages and is actively participating
in the election of the active and/or
standby router.
standby(7) - The router is a candidate to become
the next active router and sends
periodic Hello messages.
active(8) - The router is currently forwarding
packets that are sent to the group's
virtual MAC address. The router sends
periodic Hello messages.ro Enumeration .1.3.6.1.4.1.9.9.509.1.6.8 |
cwdsiMobilityGroupTableThis table provides the information about mobility
network-id. When a Mobile Node associates with a
mobility enabled SSID, the Mobile Node registers with
the network and is assigned to a particular mobility
group. At the system level, a mobility network-id
internally defines this mobility group. The mobility
network-id is the mechanism the system uses to
associate the user with a particular Fast Secure
Roaming Tunnel. As the Mobile Node roams, the system
tracks user movement, making sure that the user
maintains association with the same mobility group. SEQUENCE OF CwdsiMobilityGroupEntry .1.3.6.1.4.1.9.9.509.1.6.9 |
cwdsiMobilityGroupEntryEach entry is a set of attributes of a Mobility
network-id currently configured in WDS. CwdsiMobilityGroupEntry .1.3.6.1.4.1.9.9.509.1.6.9.1 |
cwdsiMobilityGrpNetworkIdThis objects specifies the mobility network-id which
uniquely defines a mobility group. Unsigned32 .1.3.6.1.4.1.9.9.509.1.6.9.1.1 |
cwdsiMobilityGrpTunnelAddrTypeRepresents the type of Internet address stored in the
corresponding instance of the
cwdsiMobilityGrpTunnelAddr.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.509.1.6.9.1.2 |
cwdsiMobilityGrpTunnelAddrThis object specifies the Internet address of the
Mobility tunnel, which is the tunnel source address of
the mGRE tunnel on RP. Access Point uses this address
to tunnel Mobile Node traffic.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.509.1.6.9.1.3 |
cwdsiMobilityGrpTunnelMtuThis object specifies the maximum transmission unit
of IP packet for the Mobility tunnel.ro Unsigned32 .1.3.6.1.4.1.9.9.509.1.6.9.1.4 |
cwdsiMobilityGrpFlagsThis object specifies the attributes of the mobility
tunnel.
none(0) - The mobility network-id is not
supported on L3MM.
trusted(1) - By default, a mobility network is
considered 'untrusted'. In an
untrusted network, Mobile Nodes are
required to use a DHCP-obtained IP
address. In a 'trusted' network,
Mobile Nodes are allowed to use
static IP addresses. On an untrusted
network, data forwarding path for a
Mobile Node is established and
updated by snooping DHCP packets
between the Mobile Node and the DHCP
server. On the other hand, a trusted
network data path establishment and
update is achieved by snooping IP
packets generated by the Mobile Node.
broadcast(2) - IP broadcast is allowed on the
mobility network-id corresponding to
this tunnel.
tcpMssAdjust(3)- The Access Point should do a TCP
Maximum Segment Size (MSS) adjustment
for the tunnel corresponding to the
mobility network-id.
dynamic(4) - Wireless broadcast domain
corresponding to mobility network-id
is dynamically created on an Access
Point.
multicast(5) - IP multicast is allowed on the
mobility network-id corresponding to
this tunnel.
ipDiscovery(6) - IP broadcast pings will be generated
to discover the IP address of
the wireless client.ro Bits .1.3.6.1.4.1.9.9.509.1.6.9.1.5 |
cwdsiMobilityGrpMnNumThis object specifies the number of Mobile Nodes
of which the mobility network-id is
cwdsiMobilityGrpNetworkId.ro Gauge32 UNITS "mobile-nodes" .1.3.6.1.4.1.9.9.509.1.6.9.1.6 |
ciscoWdsInfoRoamStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.509.1.7 |
cwdsiRoamStatsStartTimeThis object specifies the start time and date since
the statistics has been gathered.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.9.9.509.1.7.1 |
cwdsiRoamStatsAvgFiveSecondsThis object specifies the system-wide average number
of roams per second for the previous 5 seconds
interval.ro Gauge32 UNITS "roams-per-second" .1.3.6.1.4.1.9.9.509.1.7.2 |
cwdsiRoamStatsAvgOneMinuteThis object specifies the system-wide average number
of roams per second for the previous 1 minute
interval.ro Gauge32 UNITS "roams-per-second" .1.3.6.1.4.1.9.9.509.1.7.3 |
cwdsiRoamStatsAvgFiveMinutesThis object specifies the system-wide average number
of roams per second for the previous 5 minutes
interval.ro Gauge32 UNITS "roams-per-second" .1.3.6.1.4.1.9.9.509.1.7.4 |
cwdsiRoamMblGrpStatsTableThis table provides the information about the roaming
statistics per the mobility network-id. Roams per
second statistics will have averages for 5 seconds,
one minute and five minutes. These data will be
separated by the mobility network-id and differentiated
by roams with 'no AAA authentications',
'AAA authentications', and 'Fast Secured
Authentications'. SEQUENCE OF CwdsiRoamMblGrpStatsEntry .1.3.6.1.4.1.9.9.509.1.7.5 |
cwdsiRoamMblGrpStatsEntryEach entry is a set of roaming statistics. CwdsiRoamMblGrpStatsEntry .1.3.6.1.4.1.9.9.509.1.7.5.1 |
cwdsiRoamMblGrpStatsNetworkIdThis object specifies the mobility network-id of the
roaming Mobile Nodes. Unsigned32 .1.3.6.1.4.1.9.9.509.1.7.5.1.1 |
cwdsiRoamMblGrpStatsTotalThis object specifies the count of total roams within
the mobility network-id.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS, and at other times as
indicated by the value of cwdsiRoamStatsStartTime.ro Counter32 .1.3.6.1.4.1.9.9.509.1.7.5.1.2 |
cwdsiRoamMblGrpStatsNoAuthAaaThis object specifies the count of roams without AAA
authentications within the mobility network-id.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS, and at other times as
indicated by the value of cwdsiRoamStatsStartTime.ro Counter32 .1.3.6.1.4.1.9.9.509.1.7.5.1.3 |
cwdsiRoamMblGrpStatsAuthAaaThis object specifies the count of roams with AAA
authentications within the mobility network-id.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS, and at other times as
indicated by the value of cwdsiRoamStatsStartTime.ro Counter32 .1.3.6.1.4.1.9.9.509.1.7.5.1.4 |
cwdsiRoamMblGrpStatsFastSecuredThis object specifies the count of roams with Fast
Secured authentications within the mobility
network-id.
Discontinuities in the value of this counter can occur
at re-initialization of the WDS, and at other times as
indicated by the value of cwdsiRoamStatsStartTime.ro Counter32 .1.3.6.1.4.1.9.9.509.1.7.5.1.5 |
cwdsiRoamMblGrpStatsFiveSecondsThis object specifies the average number of roams per
second for the previous 5 seconds interval within the
mobility network-id.ro Gauge32 UNITS "roams-per-second" .1.3.6.1.4.1.9.9.509.1.7.5.1.6 |
cwdsiRoamMblGrpStatsOneMinuteThis object specifies the average number of roams per
second for the previous 1 minute interval within the
mobility network-id.ro Gauge32 UNITS "roams-per-second" .1.3.6.1.4.1.9.9.509.1.7.5.1.7 |
cwdsiRoamMblGrpStatsFiveMinutesThis object specifies the average number of roams per
second for the previous 5 minutes interval within the
mobility network-id.ro Gauge32 UNITS "roams-per-second" .1.3.6.1.4.1.9.9.509.1.7.5.1.8 |
ciscoWdsInfoMIBConform OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.509.2 |
ciscoWdsInfoMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.509.2.1 |
ciscoWdsInfoMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.509.2.2 |