Home/Catalog/CISCO-DOT11-IF-MIB

CISCO-DOT11-IF-MIB

AI MIB Summary

The CISCO-DOT11-IF-MIB enables SNMP-based monitoring and configuration of radio interface parameters, association states, and security protocols (WEP, WPA, AES/CCMP) on Cisco IEEE 802.11 Wireless LAN Access Points. It provides granular visibility into BSS topology, SSID/VLAN tagging, physical layer modulation (DSSS, OFDM), and roaming mechanisms (IAPP) for troubleshooting wireless connectivity and performance.

This MIB module provides network management support for Cisco IEEE 802.11 Wireless LAN type device (Access Point) radio interfaces. ACRONYMS AES Advanced Encryption Standard AP Access point AID Association IDentifier for wireless stations. BSS IEEE 802.11 Basic Service Set. CCMP Code Mode/CBC Mac Protocol CEPT European Conference of Postal and Telecommunications Administrations. CRC Cyclic Redundancy Check. DSSS Direct-Sequence Spread Spectrum. EAP Extensible Authentication Protocol. ERP Extended Rate PHY FHSS Frequency-Hopping Spread Spectrum. IAPP Inter-Access-Point Protocol. ICV Integrity Check Value. ISM Industrial, Scientific, and Medical. MBSSID Multiple Broadcast SSID MIC Message Integrity Check. MMH Multi-Modal Hashing. OFDM Orthogonal Frequency Division Multiplexing. PHY Physical Layer (Layer 1 in network model). PLCP Physical Layer Convergence Procedure. PMD Physical Medium Dependent. PSPF Public Secure Packet Forwarding. RF Radio Frequency. SS Spread-spectrum. SSID Radio Service Set ID. STA IEEE 802.11 wireless station. U-NII Unlicensed National information Infrastructure VLAN Virtual LAN. WEP Wired Equivalent Privacy. WGB Work-group Bridge WPA WiFi Protected Access GLOSSARY Access point Transmitter/receiver (transceiver) device that commonly connects and transports data between a wireless network and a wired network. Association The service used to establish access point or station mapping and enable STA invocation of the distribution system services. (Wireless clients attempt to connect to access points.) Basic Rate A data rate that is mandatory for client devices to support in order for them to achieve successful association. Basic Service Set The IEEE 802.11 BSS of an AP comprises of the stations directly associating with the AP. Bridge Device that connects two or more segments and reduces traffic by analyzing the destination address, filtering the frame, and forwarding the frame to all connected segments. Bridge AP It is an AP that functions as a transparent bridge between 2 wired LAN segments. Broadcast SSID Clients can send out Broadcast SSID Probe Requests to a nearby AP, and the AP will broadcast its own SSID within its beacons to response to the clients. Clients can use this Broadcast SSID to associate and communicate with the AP. Cyclic Redundancy Check CRC is an error detect mechanism that applies to frame transmission. Direct-Sequence Spread Spectrum DSSS combines a data signal at the sending station with a higher data rate bit sequence, which many refer to as a chipping code (also known as processing gain). A high processing gain increases the signals resistance to interference. DSSS sends a specific string of bits for each data bit sent. ERP-CCK Modulation This signal modulation technique is supported in PHY implementing IEEE 802.11b/g Protocol. ERP-OFDM Modulation This signal modulation technique is supported in PHY implementing IEEE 802.11g Protocol. Extensible Authentication Protocol EAP acts as the interface between a wireless client and an authentication server, such as a RADIUS server, to which the access point communicates over the wired network. Extended Rate PHY This PHY implements the IEEE 802.11g Protocol. Frequency-Hopping Spread Spectrum In FHSS, a hopping code determines the frequencies the radio will transmit and in which order. To properly receive the signal, the receiver must be set to same hopping code and listen to the incoming signal at the right time and correct frequency. The code pattern maintains a single logical channel. IEEE 802.11 Standard to encourage interoperability among wireless networking equipment. IEEE 802.11b High-rate wireless LAN standard for wireless data transfer at up to 11 Mbps. IEEE P802.11g Higher Speed Physical Layer (PHY) Extension to IEEE 802.11b, will boost wireless LAN speed to 54 Mbps by using OFDM (orthogonal frequency division multiplexing). The IEEE 802.11g specification is backward compatible with the widely deployed IEEE 802.11b standard. Inter-Access-Point Protocol The IEEE 802.11 standard does not define how access points track moving users or how to negotiate a handoff from one access point to the next, a process referred to as roaming. IAPP is a Cisco proprietary protocol to support roaming. However, IAPP does not address how the wireless system tracks users moving from one subnet to another. Independent network Network that provides peer-to-peer connectivity without relying on a complete network infrastructure. Integrity Check Value The WEP ICV shall be a 32-bit value containing the 32-bit cyclic redundancy code designed for verifying wireless data frame integrity. Message Integrity Check A MIC can, optionally, be added to WEP-encrypted 802.11 frames. MIC prevents attacks on encrypted packets. MIC, implemented on both the access point and all associated client devices, adds a few bytes to each packet to make the packets tamper-proof. Native VLAN ID A switch port and/or AP can be configured with a 'native VLAN ID'. Untagged or priority-tagged frames are implicitly associated with the native VLAN ID. The default native VLAN ID is '1' if VLAN tagging is enabled. The native VLAN ID is '0' or 'no VLAN ID' if VLAN tagging is not enabled. Node Device on a network; has its own unique network address and name. Non-Root Bridge This wireless bridge does not connect to the main wired LAN segment. It connects to a remote wired LAN segment and can associate with root bridges and other non-root bridges that accept client associations. It also can accept associations from other non-root bridges, repeater access points, and client devices. Physical Layer Convergence Procedure In IEEE 802.11 wireless LANs, PLCP defines a method of mapping the IEEE 802.11 MAC sublayer protocol data units into a framing format suitable for sending and receiving user data and management information between two or more wireless stations using the associated PMD system. Physical Medium Dependent In IEEE 802.11 wireless LANs, a PMD system, whose function defines the characteristics of, and method of transmitting and receiving data through, a wireless medium between two or more wireless stations each using the DSSS. Preamble The radio preamble are data at the head of a packet that contains information access points and client devices required by IEEE 802.11 when sending and receiving packets. Primary LAN In an AP, if the destinations of inbound unicast frames are unknown, the frames are sent toward the primary LAN defined on the device. Radio carrier Radio waves that deliver energy to a remote receiver; in other words, radio waves in a wireless LAN environment. Repeater Device that connects multiple segments, listening to each and regenerating the signal on one to every other connected one; so that the signal can travel further. Repeater or Non-root Access Point The repeater access point is not connected to the wired LAN. The Repeater is a wireless LAN transceiver that transfers data between a client and another access point, another repeater, or between two bridges. The repeater is placed within radio range of an access point connected to the wired LAN, another repeater, or an non-root bridge to extend the range of the infrastructure. Radio Frequency Radio wave and modulation process or operation. Root Access Point This access point connects clients to the main wired LAN. Root (Wireless) Bridge This wireless bridge connects to the main wired LAN. It can communicate with non-root wireless bridges, repeater access points, and client devices but not with another wireless root bridge. Only one wireless bridge in a wireless LAN can be set as the wireless root bridge. Spread-spectrum Wideband radio frequency technique that consumes more bandwidth than the narrow-band alternative but produces a signal that is louder and easier to detect. There are two types of spread-spectrum radio: frequency hopping and direct sequence. Radio Service Set ID SSID is a unique identifier that APs and clients use to identify with each other. SSID is a simple means of access control and is not for security. The SSID can be any alphanumeric entry up to 32 characters. Tag header A 'tag header' is as defined in the IEEE 802.1Q standard. An 802.1Q tag header contains a 3-bit priority field and a 12-bit VLAN ID field. A 'priority tag' has a VLAN ID of 0, to indicate 'no VLAN ID'. A 'VLAN tag' has a non-zero VLAN ID. Virtual LAN VLAN defined in the IEEE 802.1Q VLAN standard supports logically segmenting of LAN infrastructure into different subnets or workgroups so that packets are switched only between ports within the same VLAN. VLAN ID Each VLAN is identified by a 12-bit 'VLAN ID'. A VLAN ID of '0' is used to indicate 'no VLAN ID'. Valid VLAN IDs range from '1' to '4095'. VLAN of ID '4095' is the default VLAN for Cisco VoIP Phones. Wired Equivalent Privacy WEP is generally used to refer to 802.11 encryption. Work-group Bridge It is a client to APs or wireless root bridges. The radio port of a WGB serves as the uplink to the main network and the Ethernet port provides network access for devices like PC or IP phone. Upgrade of Frequencies As per the latest regulations proposed by the Japanese Government, the four channels 34 ( 5170 GHz ), 38 ( 5190 GHz), 42 ( 5210 ) and 44 ( 5230 ) in the 5150-5250 MHz band has been shifted by 10 MHz. Thus, the new channels in the 5150-5250 MHz band are 36 ( 5180 ), 40 ( 5200 ) and 44 ( 5220 ) and 48 ( 5240 ).
Main OID:
ciscoDot11IfMIB.1.3.6.1.4.1.9.9.272
186
Objects
Active
Status
7
Dependencies

Imported Objects

Objects

186 total
Object Name
ciscoDot11IfMIB
MODULE-IDENTITY
.1.3.6.1.4.1.9.9.272
ciscoDot11IfMIBNotifications
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.272.0
cd11IfStationSwitchOverNotif
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.272.0.1
cd11IfRogueApDetectedNotif
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.272.0.2
ciscoDot11IfMIBObjects
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.272.1
cd11IfConfigurations
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.272.1.1
cd11IfManagement
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.272.1.1.1
cd11IfStationConfigTable
SEQUENCE OF Cd11IfStationConfigEntry
.1.3.6.1.4.1.9.9.272.1.1.1.1
cd11IfStationConfigEntry
Cd11IfStationConfigEntry
.1.3.6.1.4.1.9.9.272.1.1.1.1.1
cd11IfStationRolerw
Enumeration
.1.3.6.1.4.1.9.9.272.1.1.1.1.1.1
cd11IfCiscoExtensionsEnablerw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.272.1.1.1.1.1.2
cd11IfAllowBroadcastSsidAssocrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.272.1.1.1.1.1.3
cd11IfPrivacyOptionMaxRatero
Integer32
.1.3.6.1.4.1.9.9.272.1.1.1.1.1.4
cd11IfEthernetEncapsulDefaultrw
Enumeration
.1.3.6.1.4.1.9.9.272.1.1.1.1.1.5
cd11IfBridgeSpacingrw
Unsigned32
.1.3.6.1.4.1.9.9.272.1.1.1.1.1.6
cd11IfDesiredSsidMaxAssocStarw
Unsigned32
.1.3.6.1.4.1.9.9.272.1.1.1.1.1.7
cd11IfAuxiliarySsidLengthro
Unsigned32
.1.3.6.1.4.1.9.9.272.1.1.1.1.1.8
cd11IfVoipExtensionsEnablerw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.272.1.1.1.1.1.9
cd11IfDesiredSsidMicAlgorithmrw
CDot11IfMicAlgorithm
.1.3.6.1.4.1.9.9.272.1.1.1.1.1.10
cd11IfDesiredSsidWepPermuteAlgrw
CDot11IfWepKeyPermuteAlgorithm
.1.3.6.1.4.1.9.9.272.1.1.1.1.1.11
cd11IfWorldModerw
Enumeration
.1.3.6.1.4.1.9.9.272.1.1.1.1.1.12
cd11IfWorldModeCountryrw
OCTET STRING
.1.3.6.1.4.1.9.9.272.1.1.1.1.1.13
cd11IfMobileStationScanParentrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.272.1.1.1.1.1.14
cd11IfPsPacketForwardEnablerw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.272.1.1.1.1.1.15
cd11IfMultipleBssidEnablerw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.272.1.1.1.1.1.16
cd11IfMobileStationListIgnorerw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.272.1.1.1.1.1.17
cd11IfMobileStationScanChannelrw
OCTET STRING
.1.3.6.1.4.1.9.9.272.1.1.1.1.1.18
cd11IfAuthAlgorithmTable
SEQUENCE OF Cd11IfAuthAlgorithmEntry
.1.3.6.1.4.1.9.9.272.1.1.1.2
cd11IfAuthAlgorithmEntry
Cd11IfAuthAlgorithmEntry
.1.3.6.1.4.1.9.9.272.1.1.1.2.1
cd11IfAuthAlgRequireEaprw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.272.1.1.1.2.1.1
cd11IfAuthAlgRequireMacAddrrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.272.1.1.1.2.1.2
cd11IfAuthAlgDefaultVlanrw
CDot11IfVlanIdOrZero
.1.3.6.1.4.1.9.9.272.1.1.1.2.1.3
cd11IfAuthAlgEapMethodrw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.9.9.272.1.1.1.2.1.4
cd11IfAuthAlgMacAddrMethodrw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.9.9.272.1.1.1.2.1.5
cd11IfWepDefaultKeysTable
SEQUENCE OF Cd11IfWepDefaultKeysEntry
.1.3.6.1.4.1.9.9.272.1.1.1.3
cd11IfWepDefaultKeysEntry
Cd11IfWepDefaultKeysEntry
.1.3.6.1.4.1.9.9.272.1.1.1.3.1
cd11IfWepDefaultKeyIndex
Unsigned32
.1.3.6.1.4.1.9.9.272.1.1.1.3.1.1
cd11IfWepDefaultKeyLenrw
Unsigned32
.1.3.6.1.4.1.9.9.272.1.1.1.3.1.2
cd11IfWepDefaultKeyValuerw
WepKeyType128
.1.3.6.1.4.1.9.9.272.1.1.1.3.1.3
cd11IfDesiredBssTable
SEQUENCE OF Cd11IfDesiredBssEntry
.1.3.6.1.4.1.9.9.272.1.1.1.5
cd11IfDesiredBssEntry
Cd11IfDesiredBssEntry
.1.3.6.1.4.1.9.9.272.1.1.1.5.1
cd11IfDesiredBssIndex
Unsigned32
.1.3.6.1.4.1.9.9.272.1.1.1.5.1.1
cd11IfDesiredBssAddrrw
MacAddress (SNMPv2-TC)
.1.3.6.1.4.1.9.9.272.1.1.1.5.1.2
cd11IfAuxSsidTable
SEQUENCE OF Cd11IfAuxSsidEntry
.1.3.6.1.4.1.9.9.272.1.1.1.6
cd11IfAuxSsidEntry
Cd11IfAuxSsidEntry
.1.3.6.1.4.1.9.9.272.1.1.1.6.1
cd11IfAuxSsidIndex
Unsigned32
.1.3.6.1.4.1.9.9.272.1.1.1.6.1.1
cd11IfAuxSsidrw
OCTET STRING
.1.3.6.1.4.1.9.9.272.1.1.1.6.1.2
cd11IfAuxSsidBroadcastSsidrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.272.1.1.1.6.1.3
cd11IfAuxSsidMaxAssocStarw
Unsigned32
.1.3.6.1.4.1.9.9.272.1.1.1.6.1.4
cd11IfAuxSsidMicAlgorithmrw
CDot11IfMicAlgorithm
.1.3.6.1.4.1.9.9.272.1.1.1.6.1.5
cd11IfAuxSsidWepPermuteAlgrw
CDot11IfWepKeyPermuteAlgorithm
.1.3.6.1.4.1.9.9.272.1.1.1.6.1.6
cd11IfAuxSsidAuthAlgTable
SEQUENCE OF Cd11IfAuxSsidAuthAlgEntry
.1.3.6.1.4.1.9.9.272.1.1.1.7
cd11IfAuxSsidAuthAlgEntry
Cd11IfAuxSsidAuthAlgEntry
.1.3.6.1.4.1.9.9.272.1.1.1.7.1
cd11IfAuxSsidAuthAlgEnablerw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.272.1.1.1.7.1.1
cd11IfAuxSsidAuthAlgRequireEaprw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.272.1.1.1.7.1.2
cd11IfAuxSsidAuthAlgRequireMacrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.272.1.1.1.7.1.3
cd11IfAuxSsidAuthAlgDefaultVlanrw
CDot11IfVlanIdOrZero
.1.3.6.1.4.1.9.9.272.1.1.1.7.1.4
cd11IfAuxSsidAuthAlgEapMethodrw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.9.9.272.1.1.1.7.1.5
cd11IfAuxSsidAuthAlgMacMethodrw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.9.9.272.1.1.1.7.1.6
cd11IfAssignedAidTable
SEQUENCE OF Cd11IfAssignedAidEntry
.1.3.6.1.4.1.9.9.272.1.1.1.8
cd11IfAssignedAidEntry
Cd11IfAssignedAidEntry
.1.3.6.1.4.1.9.9.272.1.1.1.8.1
cd11IfAssignedAid
Unsigned32
.1.3.6.1.4.1.9.9.272.1.1.1.8.1.1
cd11IfAssignedStarw
MacAddress (SNMPv2-TC)
.1.3.6.1.4.1.9.9.272.1.1.1.8.1.2
cd11IfVlanEncryptKeyTable
SEQUENCE OF Cd11IfVlanEncryptKeyEntry
.1.3.6.1.4.1.9.9.272.1.1.1.9
cd11IfVlanEncryptKeyEntry
Cd11IfVlanEncryptKeyEntry
.1.3.6.1.4.1.9.9.272.1.1.1.9.1
cd11IfVlanId
CDot11IfVlanIdOrZero
.1.3.6.1.4.1.9.9.272.1.1.1.9.1.1
cd11IfVlanEncryptKeyIndex
Unsigned32
.1.3.6.1.4.1.9.9.272.1.1.1.9.1.2
cd11IfVlanEncryptKeyLenrw
Unsigned32
.1.3.6.1.4.1.9.9.272.1.1.1.9.1.3
cd11IfVlanEncryptKeyValuerw
WepKeyType128
.1.3.6.1.4.1.9.9.272.1.1.1.9.1.4
cd11IfVlanEncryptKeyStatusrw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.9.9.272.1.1.1.9.1.5
cd11IfVlanEncryptKeyTransmitrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.272.1.1.1.9.1.6
cd11IfVlanSecurityTable
SEQUENCE OF Cd11IfVlanSecurityEntry
.1.3.6.1.4.1.9.9.272.1.1.1.10
cd11IfVlanSecurityEntry
Cd11IfVlanSecurityEntry
.1.3.6.1.4.1.9.9.272.1.1.1.10.1
cd11IfVlanSecurityVlanId
CDot11IfVlanIdOrZero
.1.3.6.1.4.1.9.9.272.1.1.1.10.1.1
cd11IfVlanSecurityVlanEnabledrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.272.1.1.1.10.1.2
cd11IfVlanBcastKeyChangeIntervalrw
Unsigned32 (0|10..10000000)
.1.3.6.1.4.1.9.9.272.1.1.1.10.1.3
cd11IfVlanBcastKeyCapabilChangerw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.272.1.1.1.10.1.4
cd11IfVlanBcastKeyClientLeaverw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.272.1.1.1.10.1.5
cd11IfVlanSecurityCiphersrw
CDot11IfCipherType
.1.3.6.1.4.1.9.9.272.1.1.1.10.1.6
cd11IfVlanSecurityRowStatusrw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.9.9.272.1.1.1.10.1.7
cd11IfVlanEncryptionModerw
Enumeration
.1.3.6.1.4.1.9.9.272.1.1.1.10.1.8
cd11IfVlanWepEncryptOptionsrw
Enumeration
.1.3.6.1.4.1.9.9.272.1.1.1.10.1.9
cd11IfVlanWepEncryptMicrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.272.1.1.1.10.1.10
cd11IfVlanWepEncryptKeyHashingrw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.272.1.1.1.10.1.11
cd11IfVlanPsPacketForwardEnablerw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.272.1.1.1.10.1.12
cd11IfRadioMonitoringTable
SEQUENCE OF Cd11IfRadioMonitoringEntry
.1.3.6.1.4.1.9.9.272.1.1.1.11
cd11IfRadioMonitoringEntry
Cd11IfRadioMonitoringEntry
.1.3.6.1.4.1.9.9.272.1.1.1.11.1
cd11IfRemoteRadioMacAddr
MacAddress (SNMPv2-TC)
.1.3.6.1.4.1.9.9.272.1.1.1.11.1.1
cd11IfRadioMonitorPollingFreqrw
Unsigned32
.1.3.6.1.4.1.9.9.272.1.1.1.11.1.2
cd11IfRadioMonitorPollingTimeOutrw
Unsigned32
.1.3.6.1.4.1.9.9.272.1.1.1.11.1.3
cd11IfLocalRadioMonitorStatusrw
Enumeration
.1.3.6.1.4.1.9.9.272.1.1.1.11.1.4
cd11IfRadioMonitorRowStatusrw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.9.9.272.1.1.1.11.1.5
cd11IfDot11UpgradeStatusTable
SEQUENCE OF Cd11IfDot11UpgradeStatusEntry
.1.3.6.1.4.1.9.9.272.1.1.1.12
cd11IfDot11UpgradeStatusEntry
Cd11IfDot11UpgradeStatusEntry
.1.3.6.1.4.1.9.9.272.1.1.1.12.1
cd11IfDot11UpgradeStatusro
Cd11IfDot11UpgradeStatus
.1.3.6.1.4.1.9.9.272.1.1.1.12.1.1
cd11IfPhyConfig
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.272.1.1.2
cd11IfPhyOperationTable
SEQUENCE OF Cd11IfPhyOperationEntry
.1.3.6.1.4.1.9.9.272.1.1.2.1
cd11IfPhyOperationEntry
Cd11IfPhyOperationEntry
.1.3.6.1.4.1.9.9.272.1.1.2.1.1
cd11IfCurrentCarrierSetro
Enumeration
.1.3.6.1.4.1.9.9.272.1.1.2.1.1.1
cd11IfModulationTyperw
Enumeration
.1.3.6.1.4.1.9.9.272.1.1.2.1.1.2
Showing 100 of 186 OID objects

CISCO-DOT11-IF-MIB Technical Reference Overview

The CISCO-DOT11-IF-MIB SNMP MIB module published by Cisco defines 186 managed OID objects, including 125 scalar/column metrics, 24 SNMP tables, and 2 trap/notification events anchored at base OID .1.3.6.1.4.1.9.9.272. Key tabular structures include cd11IfStationConfigTable, cd11IfAuthAlgorithmTable, cd11IfWepDefaultKeysTable, cd11IfDesiredBssTable, cd11IfAuxSsidTable, cd11IfAuxSsidAuthAlgTable. Monitored SNMP traps/notifications include cd11IfStationSwitchOverNotif, cd11IfRogueApDetectedNotif.

Key OID Definitions in CISCO-DOT11-IF-MIB

ciscoDot11IfMIBMODULE-IDENTITYnot-accessible
.1.3.6.1.4.1.9.9.272

This MIB module provides network management support for Cisco IEEE 802.11 Wireless LAN type device (Access Point) radio interfaces. ACRONYMS AES Advanced Encryption Standard AP Access point AID Association IDentifier for wireless stations. BSS IEEE 802.11 Basic Service Set. CCMP Code Mode/CBC Mac Protocol CEPT European Conference of Postal and Telecommunications Administrations. CRC Cyclic Redundancy Check. DSSS Direct-Sequence Spread Spectrum. EAP Extensible Authentication Protocol. ERP Extended Rate PHY FHSS Frequency-Hopping Spread Spectrum. IAPP Inter-Access-Point Protocol. ICV Integrity Check Value. ISM Industrial, Scientific, and Medical. MBSSID Multiple Broadcast SSID MIC Message Integrity Check. MMH Multi-Modal Hashing. OFDM Orthogonal Frequency Division Multiplexing. PHY Physical Layer (Layer 1 in network model). PLCP Physical Layer Convergence Procedure. PMD Physical Medium Dependent. PSPF Public Secure Packet Forwarding. RF Radio Frequency. SS Spread-spectrum. SSID Radio Service Set ID. STA IEEE 802.11 wireless station. U-NII Unlicensed National information Infrastructure VLAN Virtual LAN. WEP Wired Equivalent Privacy. WGB Work-group Bridge WPA WiFi Protected Access GLOSSARY Access point Transmitter/receiver (transceiver) device that commonly connects and transports data between a wireless network and a wired network. Association The service used to establish access point or station mapping and enable STA invocation of the distribution system services. (Wireless clients attempt to connect to access points.) Basic Rate A data rate that is mandatory for client devices to support in order for them to achieve successful association. Basic Service Set The IEEE 802.11 BSS of an AP comprises of the stations directly associating with the AP. Bridge Device that connects two or more segments and reduces traffic by analyzing the destination address, filtering the frame, and forwarding the frame to all connected segments. Bridge AP It is an AP that functions as a transparent bridge between 2 wired LAN segments. Broadcast SSID Clients can send out Broadcast SSID Probe Requests to a nearby AP, and the AP will broadcast its own SSID within its beacons to response to the clients. Clients can use this Broadcast SSID to associate and communicate with the AP. Cyclic Redundancy Check CRC is an error detect mechanism that applies to frame transmission. Direct-Sequence Spread Spectrum DSSS combines a data signal at the sending station with a higher data rate bit sequence, which many refer to as a chipping code (also known as processing gain). A high processing gain increases the signals resistance to interference. DSSS sends a specific string of bits for each data bit sent. ERP-CCK Modulation This signal modulation technique is supported in PHY implementing IEEE 802.11b/g Protocol. ERP-OFDM Modulation This signal modulation technique is supported in PHY implementing IEEE 802.11g Protocol. Extensible Authentication Protocol EAP acts as the interface between a wireless client and an authentication server, such as a RADIUS server, to which the access point communicates over the wired network. Extended Rate PHY This PHY implements the IEEE 802.11g Protocol. Frequency-Hopping Spread Spectrum In FHSS, a hopping code determines the frequencies the radio will transmit and in which order. To properly receive the signal, the receiver must be set to same hopping code and listen to the incoming signal at the right time and correct frequency. The code pattern maintains a single logical channel. IEEE 802.11 Standard to encourage interoperability among wireless networking equipment. IEEE 802.11b High-rate wireless LAN standard for wireless data transfer at up to 11 Mbps. IEEE P802.11g Higher Speed Physical Layer (PHY) Extension to IEEE 802.11b, will boost wireless LAN speed to 54 Mbps by using OFDM (orthogonal frequency division multiplexing). The IEEE 802.11g specification is backward compatible with the widely deployed IEEE 802.11b standard. Inter-Access-Point Protocol The IEEE 802.11 standard does not define how access points track moving users or how to negotiate a handoff from one access point to the next, a process referred to as roaming. IAPP is a Cisco proprietary protocol to support roaming. However, IAPP does not address how the wireless system tracks users moving from one subnet to another. Independent network Network that provides peer-to-peer connectivity without relying on a complete network infrastructure. Integrity Check Value The WEP ICV shall be a 32-bit value containing the 32-bit cyclic redundancy code designed for verifying wireless data frame integrity. Message Integrity Check A MIC can, optionally, be added to WEP-encrypted 802.11 frames. MIC prevents attacks on encrypted packets. MIC, implemented on both the access point and all associated client devices, adds a few bytes to each packet to make the packets tamper-proof. Native VLAN ID A switch port and/or AP can be configured with a 'native VLAN ID'. Untagged or priority-tagged frames are implicitly associated with the native VLAN ID. The default native VLAN ID is '1' if VLAN tagging is enabled. The native VLAN ID is '0' or 'no VLAN ID' if VLAN tagging is not enabled. Node Device on a network; has its own unique network address and name. Non-Root Bridge This wireless bridge does not connect to the main wired LAN segment. It connects to a remote wired LAN segment and can associate with root bridges and other non-root bridges that accept client associations. It also can accept associations from other non-root bridges, repeater access points, and client devices. Physical Layer Convergence Procedure In IEEE 802.11 wireless LANs, PLCP defines a method of mapping the IEEE 802.11 MAC sublayer protocol data units into a framing format suitable for sending and receiving user data and management information between two or more wireless stations using the associated PMD system. Physical Medium Dependent In IEEE 802.11 wireless LANs, a PMD system, whose function defines the characteristics of, and method of transmitting and receiving data through, a wireless medium between two or more wireless stations each using the DSSS. Preamble The radio preamble are data at the head of a packet that contains information access points and client devices required by IEEE 802.11 when sending and receiving packets. Primary LAN In an AP, if the destinations of inbound unicast frames are unknown, the frames are sent toward the primary LAN defined on the device. Radio carrier Radio waves that deliver energy to a remote receiver; in other words, radio waves in a wireless LAN environment. Repeater Device that connects multiple segments, listening to each and regenerating the signal on one to every other connected one; so that the signal can travel further. Repeater or Non-root Access Point The repeater access point is not connected to the wired LAN. The Repeater is a wireless LAN transceiver that transfers data between a client and another access point, another repeater, or between two bridges. The repeater is placed within radio range of an access point connected to the wired LAN, another repeater, or an non-root bridge to extend the range of the infrastructure. Radio Frequency Radio wave and modulation process or operation. Root Access Point This access point connects clients to the main wired LAN. Root (Wireless) Bridge This wireless bridge connects to the main wired LAN. It can communicate with non-root wireless bridges, repeater access points, and client devices but not with another wireless root bridge. Only one wireless bridge in a wireless LAN can be set as the wireless root bridge. Spread-spectrum Wideband radio frequency technique that consumes more bandwidth than the narrow-band alternative but produces a signal that is louder and easier to detect. There are two types of spread-spectrum radio: frequency hopping and direct sequence. Radio Service Set ID SSID is a unique identifier that APs and clients use to identify with each other. SSID is a simple means of access control and is not for security. The SSID can be any alphanumeric entry up to 32 characters. Tag header A 'tag header' is as defined in the IEEE 802.1Q standard. An 802.1Q tag header contains a 3-bit priority field and a 12-bit VLAN ID field. A 'priority tag' has a VLAN ID of 0, to indicate 'no VLAN ID'. A 'VLAN tag' has a non-zero VLAN ID. Virtual LAN VLAN defined in the IEEE 802.1Q VLAN standard supports logically segmenting of LAN infrastructure into different subnets or workgroups so that packets are switched only between ports within the same VLAN. VLAN ID Each VLAN is identified by a 12-bit 'VLAN ID'. A VLAN ID of '0' is used to indicate 'no VLAN ID'. Valid VLAN IDs range from '1' to '4095'. VLAN of ID '4095' is the default VLAN for Cisco VoIP Phones. Wired Equivalent Privacy WEP is generally used to refer to 802.11 encryption. Work-group Bridge It is a client to APs or wireless root bridges. The radio port of a WGB serves as the uplink to the main network and the Ethernet port provides network access for devices like PC or IP phone. Upgrade of Frequencies As per the latest regulations proposed by the Japanese Government, the four channels 34 ( 5170 GHz ), 38 ( 5190 GHz), 42 ( 5210 ) and 44 ( 5230 ) in the 5150-5250 MHz band has been shifted by 10 MHz. Thus, the new channels in the 5150-5250 MHz band are 36 ( 5180 ), 40 ( 5200 ) and 44 ( 5220 ) and 48 ( 5240 ).

cd11IfStationConfigTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.272.1.1.1.1

This table contains attributes to configure radio interfaces managed by this agent. The attributes are extensions to the configuration parameters in the dot11StationConfigTable defined in the IEEE802dot11-MIB. This table configures the station role of the interface, proprietary extensions, hierarchy, security option and parameters, and communication settings. This table has a sparse dependent relationship on the ifTable. For each entry in this table, there exists an entry in the ifTable of ifType ieee80211(71). Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent.

cd11IfAuthAlgorithmTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.272.1.1.1.2

This table contains attributes to configure authentication algorithm parameters for associations through the SSID defined by IEEE802dot11-MIB dot11DesiredSSID object. It defines attributes additional to those defined in the IEEE802dot11-MIB dot11AuthenticationAlgorithmsTable. An interface may support multiple authentication algorithms. This table has an expansion dependent relationship on the ifTable. For each entry in this table, there exists at least an entry in the ifTable of ifType ieee80211(71). This table uses the dot11AuthenticationAlgorithmsIndex of the dot11AuthenticationAlgorithmsTable defined in the IEEE802dot11-MIB as the expansion index. Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent.

cd11IfWepDefaultKeysTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.272.1.1.1.3

The dot11WEPDefaultKeysTable defined by the IEEE802dot11-MIB allows only WEP keys of length up to 40 bits. This table overrides the the dot11WEPDefaultKeysTable and supports keys of from 40 to 128 bits. A maximum of four keys can associate with any IEEE 802.11 radio interface. For devices implementing this table, they should not implement the dot11WEPDefaultKeysTable. This table has an expansion dependent relationship on the ifTable. For each entry in this table, there exists at least an entry in the ifTable of ifType ieee80211(71). Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent.

cd11IfDesiredBssTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.272.1.1.1.5

When the radio is not functioning as an access point (i.e., cd11IfStationRole is not 'roleRoot'), and for example, this radio is a repeater or bridge, this table will contain a list of preferred access points with which the radio interface should associate with. This table has an expansion dependent relationship on the ifTable. For each entry in this table, there exists at least an entry in the ifTable of ifType ieee80211(71). Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent.

cd11IfAuxSsidTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.272.1.1.1.6

When the radio is not functioning as a client station (i.e., cd11IfStationRole is not 'roleClient'), and for example, this is a access point or independent BSS, this table will contain a list of SSIDs which stations must be used to associate with this radio. This table has an expansion dependent relationship on the ifTable. For each entry in this table, there exists at least an entry in the ifTable of ifType ieee80211(71). Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent.

cd11IfAuxSsidAuthAlgTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.272.1.1.1.7

This table contains attributes to configure authentication algorithms for SSIDs listed in the cd11IfAuxSsidTable. This table extends the IEEE802dot11-MIB dot11AuthenticationAlgorithmsTable for multiple SSIDs support. Multiple SSIDs can associate with an interface and multiple authentication algorithms can apply to an auxiliary SSID. This table has an expansion dependent relationship on the ifTable. For each entry in this table, there exists at least an entry in the ifTable of ifType ieee80211(71). Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent.

cd11IfAssignedAidTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.272.1.1.1.8

When the radio is not functioning as a client station (i.e., cd11IfStationRole is not 'roleClient'), this is the list of AIDs which this agent will assign to the clients associating with it. An AID is assigned if the corresponding MAC address matches that of the client. This table has an expansion dependent relationship on the ifTable. For each entry in this table, there exists at least an entry in the ifTable of ifType ieee80211(71). Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent.

cd11IfVlanEncryptKeyTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.272.1.1.1.9

This table contains shared WEP keys for all IEEE 802.11 packets transmitted and received frames over a VLAN identified by the cwvlWlanVlanId if both VLAN and encryption are enabled (i.e., the cwvlWlanEncryptionMode is wep(2) or aes(3)) on the radio interface. If WEP encryption is enabled for the transmitted IEEE 802.11 frames, then the Default Shared WEP key in the set is used to encrypt the transmitted broadcast and multicast frames associated with the cwvlWlanVlanId. Key '1' in the set is the default key. If an individual session key is not defined for the target station address, then the Default Shared WEP key will also be used to encrypt or decrypt unicast frames associated with the cwvlWlanVlanId.

cd11IfVlanSecurityTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.272.1.1.1.10

This table contains encryption method and key rotation configurations for all VLANs on all IEEE 802.11 radio interfaces. This table has an expansion dependent relationship on the ifTable. For each entry in this table, there exists at least an entry in the ifTable of ifType ieee80211(71). VLANs are identified by the cd11IfVlanSecurityVlanId, and the actual VLAN does not have to exist or be enabled for the encryption configuration to exist.

cd11IfRadioMonitoringTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.272.1.1.1.11

This table is for monitoring of remote active IEEE 802.11 radio devices on the network. Each table entry shows an active radio being monitored by a hot standby radio on this monitoring unit. This table has a sparse dependent relationship on the ifTable. For each entry in this table, there exists an entry in the ifTable of ifType ieee80211(71). Entries on this table can be added, deleted, and modified by the NMS.

cd11IfDot11UpgradeStatusTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.272.1.1.1.12

This table represents the status of upgrade of the radios to the newer frequencies of the 5150-5250 MHz band. This table has a sparse dependent relationship on the ifTable. For each entry in this table, there exists an entry in the ifTable of ifType ieee80211(71). Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent.

cd11IfPhyOperationTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.272.1.1.2.1

This table contains the IEEE 802.11 Physical Layer operation configuration parameters for each radio interface. This table has a sparse dependent relationship on the ifTable. For each entry in this table, there exists an entry in the ifTable of ifType ieee80211(71). Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent.

cd11IfPhyFhssTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.272.1.1.2.4

This table contains the Physical Layer Frequency Hopping Spread Spectrum configuration parameters for each radio interface. This table has a sparse dependent relationship on the ifTable. For each entry in this table, there exists an entry in the ifTable of ifType ieee80211(71). Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent.

cd11IfPhyDsssTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.272.1.1.2.5

This table contains the Physical Layer Direct Sequence Spread Spectrum configuration parameters for each radio interface. This table has a sparse dependent relationship on the ifTable. For each entry in this table, there exists an entry in the ifTable of ifType ieee80211(71). Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent.

cd11IfSuppDataRatesPrivacyTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.272.1.1.2.11

This table defines the transmit and receive bit rate of the radio on each IEEE 802.11 interface and the WEP encryption support at those rates. This table has an expansion dependent relationship on the ifTable. For each entry in this table, there exists at least an entry in the ifTable of ifType ieee80211(71). Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent.

cd11IfChanSelectTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.272.1.1.2.12

This table specifies for each 802.11 channel, whether the scanning process controlled by the cd11IfPhyDsssChannelAutoEnable can select a particular channel for use. This table has an expansion dependent relationship on the ifTable. For each entry in this table, there exists at least an entry in the ifTable of ifType ieee80211(71). Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent.

cd11IfClientTxPowerTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.272.1.1.2.13

This table shows the recommended client transmit power level for the radio and selects one of the levels as the desired transmit power level to be used by the client of the radio. By adjusting the transmit power, the radio can limit the interference caused by adjacent clients using the same or adjacent channels.

cd11IfErpOfdmTxPowerTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.272.1.1.2.14

This table shows the available ERP-OFDM transmit power levels for radios implementing IEEE 802.11g Protocol and configures one of the levels as the transmit power level. This table has a sparse dependent relationship on the ifTable. For each entry in this table, there exists an entry in the ifTable of ifType ieee80211(71) and the corresponding cd11IfPhyMacSpecification is ieee802dot11g(3). For all IEEE802.11g radios with an entry in this table, the IEEE802dot11-MIB dot11PhyTxPowerTable will be used to configure ERP-CCK transmit power levels.

cd11IfFrequencyBandTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.272.1.1.2.15

This table identifies the radio frequency (sub)bands supported on the IEEE 802.11 radio interfaces while operating per the regulations imposed by the cd11IfCurrentCarrierSet. This table has an expansion dependent relationship on the ifTable. For each entry in this table, there exists at least an entry in the ifTable of ifType ieee80211(71). This table uses the cd11IfRfFrequencyBand as the expansion index. All entries in this table are created or deleted only by the agent.

cd11IfNativeTxPowerSupportTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.272.1.1.2.16

This table shows the transmit powers supported for all the radio frequency bands on the IEEE 802.11 radios. This table has an expansion dependent relationship on the ifTable. For each entry in this table, there exists at least an entry in the ifTable of ifType ieee80211(71). This table uses the cd11IfRfFrequencyBand of cd11IfFrequencyBandTable, cd11IfRadioModulationClass, and cd11IfNativeTxPowerLevel as the expansion indices. All entries in this table can only be created or deleted by the agent.

cd11IfRfNativePowerTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.272.1.1.2.17

This table configures the radio power settings for frequency bands supported on the IEEE 802.11 radios. This table serves as an alternative for the IEEE802dot11-MIB dot11PhyTxPowerTable. This table allows different transmit powers to be used on different radio frequency bands. This table has an expansion dependent relationship on the ifTable. For each entry in this table, there exists at least an entry in the ifTable of ifType ieee80211(71). This table uses the cd11IfRfFrequencyBand and cd11IfRadioModulationClass as the expansion indices. All entries in this table are created or deleted only by the agent.

cd11IfDataRatesSensitivityTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.272.1.1.2.18

This table specifies the receive sensitivity specifications of IEEE 802.11 radio interfaces. This table has an expansion dependent relationship on the ifTable. For each entry in this table, there exists at least an entry in the ifTable of ifType ieee80211(71). This table uses the cd11IfRadioModulationClass and IEEE802dot11-MIB dot11SupportedDataRatesRxIndex as the expansion indices. Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent.

cd11IfMacLayerCountersTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.272.1.2.1.1

This table includes MAC layer statistics collected by the IEEE 802.11 radio interface. This table has a sparse dependent relationship on the ifTable. For each entry in this table, there exists an entry in the ifTable of ifType ieee80211(71).

More MIBs from Cisco

Browse all CiscoMIBs →
CISCO-UNIFIED-COMPUTING-COMPUTE-MIB

The CISCO-UNIFIED-COMPUTING-COMPUTE-MIB provides SNMP-based monitoring and management of Cisco UCS compute blades, servers, and chassis components, exposing critical metrics such as CPU utilization, memory usage, thermal sensor readings, power supply status, and interface operational states. This module enables granular visibility into the health and performance of the Cisco Unified Computing System's compute subsystems for capacity planning and fault isolation.

1401 objects→
CISCO-UNIFIED-COMPUTING-STORAGE-MIB

The CISCO-UNIFIED-COMPUTING-STORAGE-MIB facilitates SNMP-based monitoring and management of storage subsystems, including Fibre Channel and iSCSI interfaces, within the Cisco Unified Computing System (UCS) fabric interconnects and blade servers. It exposes critical operational metrics such as port status, error counters, throughput statistics, and storage controller health states to enable granular visibility into the storage infrastructure.

1295 objects→
CISCO-UNIFIED-COMPUTING-VNIC-MIB

The CISCO-UNIFIED-COMPUTING-VNIC-MIB enables SNMP-based monitoring and management of Virtual Network Interface Card (vNIC) attributes, including operational status, traffic counters, and binding configurations, within the Cisco Unified Computing System (UCS) fabric interconnects and server blades.

1161 objects→
CERENT-GENERIC-MIB

SNMP MIB module

984 objects→
CISCO-UNIFIED-COMPUTING-BIOS-MIB

The CISCO-UNIFIED-COMPUTING-BIOS-MIB enables SNMP-based monitoring and configuration of BIOS-level parameters, firmware versions, and hardware initialization states within Cisco Unified Computing System (UCS) servers. It provides visibility into critical server boot diagnostics, BIOS settings, and hardware readiness indicators to facilitate low-level infrastructure management and troubleshooting.

937 objects→
CISCO-UNIFIED-COMPUTING-ETHER-MIB

The CISCO-UNIFIED-COMPUTING-ETHER-MIB provides SNMP management interfaces for monitoring Ethernet interface statistics, link states, and error counters on Cisco Unified Computing System (UCS) fabric interconnects and blade server line cards. This module enables the tracking of physical layer connectivity, port throughput, and packet error rates within the UCS Ethernet switching infrastructure.

920 objects→