CISCO-SDSL-LINE-MIB
AI MIB Summary
The CISCO-SDSL-LINE-MIB enables monitoring and configuration of symmetric DSL (SDSL) line interfaces on Cisco hardware, tracking critical physical layer metrics such as attenuation, SNR margin, coding violations, and sync defects. It supports the definition of technology-agnostic configuration profiles for SDSL modems while maintaining structural consistency with existing ADSL MIB standards.
This MIB module describes all variations of the symmetric DSL line interfaces. The structure of this module resembles and maintains consistency with the ADSL-LINE-MIB, ADSL-DMT-LINE-MIB, CISCO-ADSL-DMT-LINE-MIB, and CISCO-ADSL-CAP-LINE-MIB. Observe that the tables in this module do not necessarily extend the tables defined by the these mibs. Currently, only those tables that contain configuration information extend the profile tables defined by the above modules. This allows the management client to define DSL configuration profiles that apply across all DSL modems, independent of the technology being utilized by the modem.
*** DEFINITIONS ***
ATTENUATION Attenuation is a decrease in the strength of a signal over the length of a cable.
CODING VIOLATION A coding violation occurs when the incoming signal exhibits a CRC anomaly.
DOWNSTREAM The flow of data in the direction from the ATU-C to ATU-R.
ERRORED SECOND A second with one or more coding violations or one or more incoming defects (e.g., LOS or LOSQ).
LINE RATE The total data rate supported by a line. Observe that the payload rate is equal the line rate for the earliest implementations of SDSL. However, the payload rate maybe less than the line rate for future implementations.
LOSS OF SYNC DEFECT A Loss of Sync Defect is defined as 3 consecutive received frames which contain one or more errors in the framing bits. A Loss of Sync Defect shall be cleared when at least 2 consecutive received frames contain no errors in the framing bits.
LOSS OF SYNC FAILURE A LOSW Failure is defined as at least 2 consecutive seconds of LOSW Defect. The LOSW Failure should be cleared when the LOSW defect is absent for 20 seconds or less. (i.e. clear within 20 seconds ).
MARGIN (also referred to as 'SNR margin') The difference between the SNR of the received signal and the SNR required to provide a BER of 10E-7.
SEVERELY ERRORED SECOND A one second interval during which or more LOSW or CV defects are declared.
UNAVAILABLE SECOND A Unavailable Second is defined as a one second interval during which LOSW Failure ( at least 2 seconds of LOSW Defect ).
UPSTREAM The flow of data in the direction from the ATU-R to ATU-C.
*** ABBREVIATIONS, ACRONYMS, AND SYMBOLS ***
ADSL - Asymmetric Digital Subscriber Line.
ATM - Asynchronous Transfer Mode.
BER - Bit Error Ratio.
CV - Coding Violation.
DSL - Digital Subscriber Line.
ES - Errored Second.
LOS - Loss Of Sync.
LOSQ - Loss Of Signal Quality.
LOSW - Loss of Sync Word Failure
PSD - Power Spectral Density.
SES - Severely Errored Second.
SNR - Signal-to-Noise Ratio.
STM - Synchronous Transfer Mode.
STU-C - SDSL Transceiver Unit, Central Office end.
STU-R - ADSL Transceiver Unit, Remote terminal end.
UAS - UnAvailable Second.
120
Objects
Active
Status
8
Dependencies
Imported Objects
Objects
120 total| Object Name |
|---|
ciscoSdslLineMIB OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155 |
RFC1155-SMI Unknown .1.3.6.1.4.1.9.9.155 |
ciscoSdslLineMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.1 |
cSdslLineTableThis table contains the enterprise-specific common attributes
describing both ends of SDSL lines supported by the system. SEQUENCE OF CSdslLineEntry .1.3.6.1.4.1.9.9.155.1.1 |
cSdslLineEntryA set of enterprise-specific common attributes describing both
ends of an SDSL line supported by the system. There exists an
entry for each ifEntry with an ifType of sdsl(96). CSdslLineEntry .1.3.6.1.4.1.9.9.155.1.1.1 |
cSdslLineCodingSpecifies encoding of signal used by this line. Other types
may be added in the future.ro Enumeration .1.3.6.1.4.1.9.9.155.1.1.1.1 |
cSdslLineFramingThis object specifies the current Transmission Convergence
framing structure being used by the interface.ro Enumeration .1.3.6.1.4.1.9.9.155.1.1.1.2 |
cSdslLineSpecificThis object specifies an object identifier of an instance of
an object in the MIB. The implementation determines the
application of this object. For example, an implementation
may use this object to provide a reference to the port-class
physical entity (see the ENTITY-MIB for further details)
corresponding to the SDSL line.ro VariablePointer -- Rsyntax OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.1.1.1.3 |
cSdslLineConfProfileThis object specifies the row in the adslLineConfProfileTable
(see the ADSL-LINE-MIB for further details), which applies for
this SDSL line interface.
In the case the implementation utilizes 'dynamic mode' (see
the ADSL-LINE-MIB for further details), then the value of this
object defaults to the name of a configuration profile
designated by the implementation as the default configuration
profile.
In the case the implementation utilizes 'static mode', then the
the value of this object is read-only.rw AdslLineProfileName -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.9.155.1.1.1.4 |
cSdslLineAlarmConfProfileThis object specifies the row in the
adslLineAlarmConfProfileTable (see the ADSL-LINE-MIB for further
details), which applies for this SDSL line interface.
In the case the implementation utilizes 'dynamic mode' (see
the ADSL-LINE-MIB for further details), then the value of this
object defaults to the name of an alarm configuration profile
designated by the implementation as the default alarm
configuration profile.
In the case the implementation utilizes 'static mode', then the
the value of this object is read-only.rw AdslLineProfileName -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.9.155.1.1.1.5 |
cSdslStucPhysTableThis table contains enterprise-specific physical layer
parameters for STU-C class devices supported by the system. SEQUENCE OF CSdslStucPhysEntry .1.3.6.1.4.1.9.9.155.1.2 |
cSdslStucPhysEntryA set of enterprise-specific physical-layer parameters for an
STU-C class device supported by the system. There exists an
entry for each ifEntry with an ifType of sdsl(96). CSdslStucPhysEntry .1.3.6.1.4.1.9.9.155.1.2.1 |
cSdslStucInvSerialNumberThis object specifies the vendor specific string that
identifies the vendor STU-C.ro SnmpAdminString .1.3.6.1.4.1.9.9.155.1.2.1.1 |
cSdslStucInvVendorIdThis object specifies the vendor identifier assigned according
to T1.220ro SnmpAdminString .1.3.6.1.4.1.9.9.155.1.2.1.2 |
cSdslStucInvVersionNumberThis object specifies the vendor specific version number of
the STU-C.ro SnmpAdminString .1.3.6.1.4.1.9.9.155.1.2.1.3 |
cSdslStucStateThis object specifies the state of the STU-C transceiver.ro Enumeration .1.3.6.1.4.1.9.9.155.1.2.1.4 |
cSdslStucDefectThis object specifies any possible defects currently being
exhibited by the STU-C.
This object has the intention of supplementing ifOperStatus.ro SdslStuxDefect -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.9.155.1.2.1.5 |
cSdslStucCurrRateThis object specifies the rate the STU-C transceiver was
able to obtain following training.ro INTEGER .1.3.6.1.4.1.9.9.155.1.2.1.6 |
cSdslStucCurrSnrMgnThis object specifies the SNR margin as seen by this STU-C with
respect to its received signal.ro Gauge -- Units -- tenth dB .1.3.6.1.4.1.9.9.155.1.2.1.7 |
cSdslStucCurrGainThis object specifies gain applied to this STU-C's receiver.
This object is deprecated by cSdslStucCurrGainRev which has
no specified range.rodeprecated INTEGER(-200..200) -- Units -- tenth dB .1.3.6.1.4.1.9.9.155.1.2.1.8 |
cSdslStucCurrOutputPwrThis object specifies the measured total output power
transmitted by this STU-C. This is the measurement that was
reported during the last activation sequence.ro Gauge -- Units -- tenth dBm .1.3.6.1.4.1.9.9.155.1.2.1.9 |
cSdslStucCurrAtnMeasured difference in the total power transmitted by
the peer STU-R and the total power received by this STU-C.ro Gauge -- Units -- tenth dBm .1.3.6.1.4.1.9.9.155.1.2.1.10 |
cSdslStucCurrGainRevThis object specifies gain applied to this STU-C's receiver.
This object deprecates cSdslStucCurrGainRev and has
no specified range.ro INTEGER -- Units -- tenth dB .1.3.6.1.4.1.9.9.155.1.2.1.11 |
cSdslSturPhysTableThis table contains enterprise-specific physical layer
parameters for STU-R class devices supported by the system.
::= { ciscoSdslLineMIBObjects 3 }
cSdslSturPhysEntry OBJECT-TYPE
SYNTAX CSdslSturPhysEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION SEQUENCE OF CSdslSturPhysEntry .1.3.6.1.4.1.9.9.155.1.7 |
cSdslStucIntervalTableThis table contains physical-layer statistics intervals for
STU-C class devices supported by the system. The interval
tables are modeled after RFC 2493, Textual Conventions for
MIB Modules Using Performance History Based on 15 Minute
Intervals, RFC 2493 SEQUENCE OF CSdslStucIntervalEntry .1.3.6.1.4.1.9.9.155.1.8 |
cSdslStucIntervalEntryA 15-miute interval of physical-layer statistics for a STU-C
class device supported by the system. There exists up to 96
entries for each ifEntry with an ifType of sdsl(96). CSdslStucIntervalEntry .1.3.6.1.4.1.9.9.155.1.8.1 |
cSdslStucIntervalNumberThe interval in which the statistics were collected, where the
value of 1 represents the most recent interval, and the value of
96 represents the interval collected 24 hours ago. Intervals
2..96 are optional. INTEGER .1.3.6.1.4.1.9.9.155.1.8.1.1 |
cSdslStucIntervalValidDataThis object specifies whether the data for this interval
is valid.ro TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.155.1.8.1.2 |
cSdslStucIntervalLOSsThis object specifies the number of seconds in the interval
when the STU-C experienced LOS.ro PerfIntervalCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.4.1.9.9.155.1.8.1.3 |
cSdslStucIntervalLOSQsThis object specifies the number of seconds in the interval
when the STU-C experienced LOSQ.ro PerfIntervalCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.4.1.9.9.155.1.8.1.4 |
cSdslStucIntervalCVsThis object specifies the number of coding violations
experienced by the STU-C in the interval.ro PerfIntervalCount -- Rsyntax Gauge .1.3.6.1.4.1.9.9.155.1.8.1.5 |
cSdslStucIntervalESsThis object specifies the number of errored seconds
experienced by the STU-C in the interval.ro PerfIntervalCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.4.1.9.9.155.1.8.1.6 |
cSdslStucIntervalSESsThis object specifies the number of severely errored seconds
experienced by the STU-C in the interval.ro PerfIntervalCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.4.1.9.9.155.1.8.1.7 |
cSdslStucIntervalUASsThis object specifies the number of unavailable seconds
experienced by the STU-C in the interval.ro PerfIntervalCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.4.1.9.9.155.1.8.1.8 |
cSdslStucIntervalInitsThis object specifies the number of line initializations
attempted by the STU-C in the interval.ro PerfIntervalCount -- Rsyntax Gauge .1.3.6.1.4.1.9.9.155.1.8.1.9 |
cSdslStucIntervalUnavlRsrcsThis object specifies the number of packets discarded on the
STU-C due to unavailable resources, such as lack of buffer
space in the interval.ro PerfIntervalCount -- Rsyntax Gauge .1.3.6.1.4.1.9.9.155.1.8.1.10 |
cSdslSturIntervalTableThis table contains physical-layer statistics intervals for
STU-R class devices supported by the system. The interval
tables are modeled after RFC 2493, Textual Conventions for
MIB Modules Using Performance History Based on 15 Minute
Intervals, RFC 2493 SEQUENCE OF CSdslSturIntervalEntry .1.3.6.1.4.1.9.9.155.1.9 |
cSdslSturIntervalEntryA 15-miute interval of physical-layer statistics for a STU-R
class device supported by the system. There exists up to 96
entries for each ifEntry with an ifType of sdsl(96). CSdslSturIntervalEntry .1.3.6.1.4.1.9.9.155.1.9.1 |
cSdslSturIntervalNumberThe interval in which the statistics were collected, where the
value of 1 represents the most recent interval, and the value of
96 represents the interval collected 24 hours ago. Intervals
2..96 are optional. INTEGER .1.3.6.1.4.1.9.9.155.1.9.1.1 |
cSdslSturIntervalValidDataThis object specifies whether the data for this interval
is valid.ro TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.155.1.9.1.2 |
cSdslSturIntervalLOSsThis object specifies the number of seconds in the interval
when the STU-R experienced LOS.ro PerfIntervalCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.4.1.9.9.155.1.9.1.3 |
cSdslSturIntervalLOSQsThis object specifies the number of seconds in the interval
when the STU-R experienced LOSQ.ro PerfIntervalCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.4.1.9.9.155.1.9.1.4 |
cSdslSturIntervalCVsThis object specifies the number of coding violations
experienced by the STU-R in the interval.ro PerfIntervalCount -- Rsyntax Gauge .1.3.6.1.4.1.9.9.155.1.9.1.5 |
cSdslSturIntervalESsThis object specifies the number of errored seconds
experienced by the STU-R in the interval.ro PerfIntervalCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.4.1.9.9.155.1.9.1.6 |
cSdslSturIntervalSESsThis object specifies the number of severely errored seconds
experienced by the STU-R in the interval.ro PerfIntervalCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.4.1.9.9.155.1.9.1.7 |
cSdslSturIntervalUASsThis object specifies the number of unavailable seconds
experienced by the STU-R in the interval.ro PerfIntervalCount -- Rsyntax Gauge -- Units -- seconds .1.3.6.1.4.1.9.9.155.1.9.1.8 |
cSdslLineConfProfileTableThis table extends the adslLineConfProfileTable and contains
enterprise-specific SDSL line configuration information. SEQUENCE OF CSdslLineConfProfileEntry .1.3.6.1.4.1.9.9.155.1.14 |
cSdslLineConfProfileEntryA configuration profile containing enterprise-specific SDSL
line configuration information. CSdslLineConfProfileEntry .1.3.6.1.4.1.9.9.155.1.14.1 |
cSdslLineMaxRateThis object specifies the desired line rate which the STU-C
will attempt to train at.rw INTEGER(144000|272000|400000|528000|784000|1040000|1168000|1552000|2064000|2320000) -- Units -- bps .1.3.6.1.4.1.9.9.155.1.14.1.1 |
cSdslLineFramingModeThis object specifies the desired Transmission Convergence
framing structure being used by the interface.rw Enumeration .1.3.6.1.4.1.9.9.155.1.14.1.2 |
cSdslStucTargetSnrMgnThis object specifies the target SNR margin. This is the
desired noise margin the STU-C must achieve with a BER of
10-7 or better to successfully complete training. The value
for this object must be in multiples of 10. The specified
value will be rounded down to the nearest valid tenth dB
level if the value is not in multiples of 10.rw INTEGER .1.3.6.1.4.1.9.9.155.1.14.1.3 |
cSdslStucMaxSnrMgnThis object specifies the maximum acceptable SNR margin.
If the noise margin exceeds this level, then the STU-C should
attempt to reduce its power output to optimize its operation.
The value for this object must be in multiples of 10. The
specified value will be rounded down to the nearest valid
tenth dB level if the value is not in multiples of 10.rw INTEGER .1.3.6.1.4.1.9.9.155.1.14.1.4 |
cSdslStucMinSnrMgnThis object specifies the minimum acceptable SNR margin.
If the noise margin falls below this level, the STU-C will
retrain. The value for this object must be in multiples of 10.
The specified value will be rounded down to the nearest valid
tenth dB level if the value is not in multiples of 10.rw INTEGER .1.3.6.1.4.1.9.9.155.1.14.1.5 |
cSdslStucOutputPwrThis object specifies the transmit power level used by
the STU-C. The value for this object must be in multiples
of 10. The specified value will be rounded down to the
nearest valid tenth dB level if the value is not in
multiples of 10.rw INTEGER .1.3.6.1.4.1.9.9.155.1.14.1.6 |
cSdslShdslLineMaxRateThis object specifies the desired line rate at which the
G.shdsl STU-C will attempt to train.rw Enumeration .1.3.6.1.4.1.9.9.155.1.14.1.7 |
cSdslStucPsdMaskTypeThis object specifies the PSD mask type for the transceiver.
For all values of the cSdslShdslLineMaxRate, the symmetric PSD
masktype is selectable. Asymmetric mask is only selectable for
the following rates: 776000, 784000, 1552000, 2056000, 2312000.rw Enumeration .1.3.6.1.4.1.9.9.155.1.14.1.8 |
cSdslStucAnnexThis object specifies the operating conditions for the port
of G.shdsl CO equipment . Annex A is optimized for conditions
typically encountered within the North American network,whereas
Annex B is optimized for conditions typically encountered
within the European network.rw Enumeration .1.3.6.1.4.1.9.9.155.1.14.1.9 |
cSdslLineEquipmentTypeThis object specifies the type of the STU device ,either
STU-C or STU-Rrw Enumeration .1.3.6.1.4.1.9.9.155.1.14.1.10 |
cSdslLineAutoRateEnableThis object specifies whether the device uses the rate
adaptive training mode.rw TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.155.1.14.1.11 |
cSdslStucThresholdSnrMgnThis object specifies the SNR margin threshold. An
appropriate alarm should be generated when the difference
between the actual SNR and the SNR required to maintain BER
of 10E-7 is less than this value. The value for this object
must be in multiples of 10. The specified value will be
rounded down to the nearest valid tenth dB level if the
value is not in multiples of 10.
If the agent implements the CISCO-ENTITY-ALARM-MIB, the alarm
generated should be through the mechanism defined by the
CISCO-ENTITY-ALARM-MIB. Furthermore, the default severity
of this alarm should be 'minor'.rw INTEGER .1.3.6.1.4.1.9.9.155.1.14.1.12 |
cSdslSturAnnexThis object specifies the operating conditions for the port
of G.shdsl CPE equipment. Annex A is optimized for conditions
typically encountered within the North American network,whereas
Annex B is optimized for conditions typically encountered
within the European network.rw Enumeration .1.3.6.1.4.1.9.9.155.1.14.1.13 |
cSdslLineAlarmConfProfileTableThis table extends the adslLineAlarmConfProfileTable and
contains enterprise-specific SDSL line configuration information
pertaining to alarms. SEQUENCE OF CSdslLineAlarmConfProfileEntry .1.3.6.1.4.1.9.9.155.1.15 |
cSdslLineAlarmConfProfileEntryA configuration profile containing enterprise-specific SDSL
line configuration information pertaining to alarms CSdslLineAlarmConfProfileEntry .1.3.6.1.4.1.9.9.155.1.15.1 |
cSdslStucThreshMinRateThis object specifies the line rate threshold. When the
agent observes the line rate fall below this value, an
appropriate alarm should be generated.
The default value for this object should be the value of
the cSdslLineMaxRate object.
If the agent implements the CISCO-ENTITY-ALARM-MIB, the
alarm generated should be through the mechanism defined by
the CISCO-ENTITY-ALARM-MIB. Furthermore, the default
severity of this alarm should be 'minor'.rw INTEGER .1.3.6.1.4.1.9.9.155.1.15.1.1 |
cSdslStucThreshMinSnrMgnThis object specifies the SNR margin threshold. When the
agent observes the received SNR margin fall below this value,
an appropriate alarm should be generated.
If the agent implements the CISCO-ENTITY-ALARM-MIB, the alarm
generated should be through the mechanism defined by the
CISCO-ENTITY-ALARM-MIB. Furthermore, the default severity
of this alarm should be 'minor'.rw INTEGER .1.3.6.1.4.1.9.9.155.1.15.1.2 |
ciscoSdslLineMIBNotificationsPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.2 |
ciscoSdslLineMIBNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.2.0 |
ciscoSdslLineMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.3 |
ciscoSdslLineMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.3.1 |
ciscoSdslLineMIBStucCompliance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.3.1.1 |
ciscoSdslLineMIBSturCompliance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.3.1.2 |
ciscoSdslLineMIBStucComplianceRev1 OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.3.1.3 |
ciscoSdslLineMIBSturComplianceRev1 OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.3.1.4 |
ciscoSdslLineMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.3.2 |
cSdslStucBasicGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.3.2.1 |
cSdslSturBasicGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.3.2.2 |
cSdslSturGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.3.2.3 |
cSdslStucPMCounterGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.3.2.4 |
cSdslStucPM15MinIntervalGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.3.2.5 |
cSdslStucPM1DayIntervalGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.3.2.6 |
cSdslSturPMCounterGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.3.2.7 |
cSdslSturPM15MinIntervalGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.3.2.8 |
cSdslSturPM1DayIntervalGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.3.2.9 |
cSdslStucRateAdaptiveGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.3.2.10 |
cSdslStucAlarmConfProfileGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.3.2.11 |
cSdslStucBasicGroupRev1 OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.3.2.12 |
cSdslSturBasicGroupRev1 OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.3.2.13 |
cSdslStucBasicGroupRev2 OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.3.2.14 |
cSdslSturBasicGroupRev2 OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.3.2.15 |
cSdslSturGroupRev1 OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.155.3.2.16 |
cSdslSturPerfDataEntryA set of physical-layer statistics for an STU-R class device
supported by the system. There exists an entry for each ifEntry
with an ifType of sdsl(96). CSdslSturPerfDataEntry .cSdslSturPerfDataTable.1 |
cSdslSturPerfLOSsThis object specifies the number of LOS failures experienced
by the STU-R since agent reset.ro Counter .cSdslSturPerfDataTable.1.1 |
cSdslSturPerfLOSQsThis object specifies the number of LOSQ failures experienced
by the STU-R since agent reset.ro Counter .cSdslSturPerfDataTable.1.2 |
cSdslSturPerfCVsThis object specifies the number of coding violations
experienced by the STU-R since agent reset.ro Counter .cSdslSturPerfDataTable.1.3 |
cSdslSturPerfESsThis object specifies the number of errored seconds
experienced by the STU-R since agent reset.ro Counter -- Units -- seconds .cSdslSturPerfDataTable.1.4 |
cSdslSturPerfSESsThis object specifies the number of severely errored
seconds experienced by the STU-R since agent reset.ro Counter -- Units -- seconds .cSdslSturPerfDataTable.1.5 |
cSdslSturPerfUASsThis object specifies the number of unavailable seconds
experienced by the STU-R since agent reset.ro Counter -- Units -- seconds .cSdslSturPerfDataTable.1.6 |
cSdslSturPerfValidIntervalsThe number of previous far end intervals for
which valid data was collected. The value will be
96 unless the interface was brought online within
the last 24 hours, in which case the value will be
the number of complete 15 minute far end
intervals since the interface has been online.ro INTEGER .cSdslSturPerfDataTable.1.7 |
cSdslSturPerfInvalidIntervalsThe number of far-end performance data 15-minute intervals in
the range from 0 to cSdslSturPerfValidIntervals for which no
data is available. This object will typically be zero except in
cases where the data for some intervals are not available (e.g.,
in proxy situations).ro INTEGER .cSdslSturPerfDataTable.1.8 |
cSdslSturPerfCurr15MinTimeElapseThe number of seconds that have elapsed since the beginning of
the current measurement period. If, for some reason, such as an
adjustment in the system's time-of-day clock, the current
interval exceeds the maximum value, the agent will return
the maximum value.ro SdslPerfTimeElapsed .cSdslSturPerfDataTable.1.9 |
cSdslSturPerfCurr15MinLOSsThis object specifies the number of seconds in the current
15-minute interval when the STU-R experienced LOS.ro PerfCurrentCount -- Rsyntax Gauge -- Units -- seconds .cSdslSturPerfDataTable.1.10 |
cSdslSturPerfCurr15MinLOSQsThis object specifies the number of seconds in the current
15-minute interval when the STU-R experienced LOSQ.ro PerfCurrentCount -- Rsyntax Gauge -- Units -- seconds .cSdslSturPerfDataTable.1.11 |
cSdslSturPerfCurr15MinCVsThis object specifies the number of coding violations
experienced by the STU-R in the current 15-minute interval.ro PerfCurrentCount -- Rsyntax Gauge .cSdslSturPerfDataTable.1.12 |
cSdslSturPerfCurr15MinESsThis object specifies the number of errored seconds
experienced by the STU-R in the current 15-minute interval.ro PerfCurrentCount -- Rsyntax Gauge -- Units -- seconds .cSdslSturPerfDataTable.1.13 |
cSdslSturPerfCurr15MinSESsThis object specifies the number of severely errored seconds
experienced by the STU-R in the current 15-minute interval.ro PerfCurrentCount -- Rsyntax Gauge -- Units -- seconds .cSdslSturPerfDataTable.1.14 |
cSdslSturPerfCurr15MinUASsThis object specifies the number of unavailable seconds
experienced by the STU-R in the current 15-minute interval.ro PerfCurrentCount -- Rsyntax Gauge -- Units -- seconds .cSdslSturPerfDataTable.1.15 |
cSdslSturPerfCurr1DayTimeElapsedThe number of seconds that have elapsed since the beginning of
the current measurement period. If, for some reason, such as an
adjustment in the system's time-of-day clock, the current
interval exceeds the maximum value, the agent will return
the maximum value.ro SdslPerfTimeElapsed .cSdslSturPerfDataTable.1.16 |
cSdslSturPerfCurr1DayLOSsThis object specifies the number of seconds experienced by the
STU-R in the current 1-day interval when there was LOS.ro SdslPerfCurrDayCount -- Rsyntax Gauge -- Units -- seconds .cSdslSturPerfDataTable.1.17 |
cSdslSturPerfCurr1DayLOSQsThis object specifies the number of seconds experienced by the
STU-R in the current 1-day interval when there was LOSQ.ro SdslPerfCurrDayCount -- Rsyntax Gauge -- Units -- seconds .cSdslSturPerfDataTable.1.18 |
cSdslSturPerfCurr1DayCVsThis object specifies the number of coding violations
experienced by the STU-R in the current 1-day interval.ro SdslPerfCurrDayCount -- Rsyntax Gauge .cSdslSturPerfDataTable.1.19 |
cSdslSturPerfCurr1DayESsThis object specifies the number of errored seconds
experienced by the STU-R in the current 1-day interval.ro SdslPerfCurrDayCount -- Rsyntax Gauge -- Units -- seconds .cSdslSturPerfDataTable.1.20 |
cSdslSturPerfCurr1DaySESsThis object specifies the number of severely errored seconds
experienced by the STU-R in the current 1-day interval.ro SdslPerfCurrDayCount -- Rsyntax Gauge -- Units -- seconds .cSdslSturPerfDataTable.1.21 |
cSdslSturPerfCurr1DayUASsThis object specifies the number of unavailable seconds
experienced by the STU-R in the current 1-day interval.ro SdslPerfCurrDayCount -- Rsyntax Gauge -- Units -- seconds .cSdslSturPerfDataTable.1.22 |
cSdslSturPerfPrev1DayMoniSecsThe amount of time in the previous 1-day interval over which
the performance monitoring information is actually counted.
This value will be the same as the interval duration except
in a situation where performance monitoring data could not be
collected for any reason.ro INTEGER .cSdslSturPerfDataTable.1.23 |
cSdslSturPerfPrev1DayLOSsThis object specifies the number of seconds in the current
1-day interval when the STU-R experienced LOS.ro SdslPerfPrevDayCount -- Rsyntax Gauge -- Units -- seconds .cSdslSturPerfDataTable.1.24 |
cSdslSturPerfPrev1DayLOSQsThis object specifies the number of seconds in the previous
1-day interval when the STU-R experienced LOSQ.ro SdslPerfPrevDayCount -- Rsyntax Gauge -- Units -- seconds .cSdslSturPerfDataTable.1.25 |
cSdslSturPerfPrev1DayCVsThis object specifies the number of coding violations
experienced by the STU-R in the previous 1-day interval.ro SdslPerfPrevDayCount -- Rsyntax Gauge .cSdslSturPerfDataTable.1.26 |
cSdslSturPerfPrev1DayESsThis object specifies the number of errored seconds
experienced by the STU-R in the previous 1-day interval.ro SdslPerfPrevDayCount -- Rsyntax Gauge -- Units -- seconds .cSdslSturPerfDataTable.1.27 |
cSdslSturPerfPrev1DaySESsThis object specifies the number of severely errored seconds
experienced by the STU-R in the previous 1-day interval.ro SdslPerfPrevDayCount -- Rsyntax Gauge -- Units -- seconds .cSdslSturPerfDataTable.1.28 |
cSdslSturPerfPrev1DayUASsThis object specifies the number of unavailable seconds
experienced by the STU-R in the previous 1-day interval.ro SdslPerfPrevDayCount -- Rsyntax Gauge -- Units -- seconds .cSdslSturPerfDataTable.1.29 |