CISCO-LWAPP-SYS-MIB
This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Access Point Protocol tunnel from Cisco Light-weight LWAPP Access Points.
This MIB provides global configuration and status information for the controller. All general system related information is presented in this MIB.
The relationship between CC and the LWAPP APs can be depicted as follows:
+......+ +......+ +......+
+ + + + + +
+ CC + + CC + + CC +
+ + + + + +
+......+ +......+ +......+
.. . . .. . . . . . . . . . . . . . . . . . .
+......+ +......+ +......+ +......+
+ + + + + + + +
+ AP + + AP + + AP + + AP +
+ + + + + + + +
+......+ +......+ +......+ +......+
. . . . . . . . . . . . . . . . . . .
+......+ +......+ +......+ +......+
+ + + + + + + +
+ MN + + MN + + MN + + MN +
+ + + + + + + +
+......+ +......+ +......+ +......+
The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard.
LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller.
GLOSSARY
Access Point ( AP )
An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients.
LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends them to the controller to which it is logically connected.
Light Weight Access Point Protocol ( LWAPP )
This is a generic protocol that defines the communication between the Access Points and the Central Controller.
Mobile Node ( MN )
A roaming 802.11 wireless device in a wireless network associated with an access point. Mobile Node and client are used interchangeably.
Extensible Authentication Protocol ( EAP )
EAP is a universal authentication protocol used in wireless and PPP networks. It is defined by RFC 3748.
EAP-Flexible Authentication ( EAP-FAST )
This protocol is used via secure tunneling for 802.1X EAP.
PAC
PAC (Protected Access Credential) is a meachanism for mutual authentication in EAP-FAST.
REFERENCE
[1] Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications.
[2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol.
[3] IEEE 802.1X - Authentication for Wireless and Wired Connections.
Main OID:
ciscoLwappSysMIB.1.3.6.1.4.1.9.9.618
136
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
136 total| Object Name |
|---|
ciscoLwappSysMIBThis MIB is intended to be implemented on all those
devices operating as Central controllers, that
terminate the Light Weight Access Point Protocol
tunnel from Cisco Light-weight LWAPP Access Points.
This MIB provides global configuration and status
information for the controller. All general system
related information is presented in this MIB.
The relationship between CC and the LWAPP APs
can be depicted as follows:
+......+ +......+ +......+
+ + + + + +
+ CC + + CC + + CC +
+ + + + + +
+......+ +......+ +......+
.. . .
.. . .
. . . .
. . . .
. . . .
. . . .
+......+ +......+ +......+ +......+
+ + + + + + + +
+ AP + + AP + + AP + + AP +
+ + + + + + + +
+......+ +......+ +......+ +......+
. . .
. . . .
. . . .
. . . .
. . . .
+......+ +......+ +......+ +......+
+ + + + + + + +
+ MN + + MN + + MN + + MN +
+ + + + + + + +
+......+ +......+ +......+ +......+
The LWAPP tunnel exists between the controller and
the APs. The MNs communicate with the APs through
the protocol defined by the 802.11 standard.
LWAPP APs, upon bootup, discover and join one of the
controllers and the controller pushes the configuration,
that includes the WLAN parameters, to the LWAPP APs.
The APs then encapsulate all the 802.11 frames from
wireless clients inside LWAPP frames and forward
the LWAPP frames to the controller.
GLOSSARY
Access Point ( AP )
An entity that contains an 802.11 medium access
control ( MAC ) and physical layer ( PHY ) interface
and provides access to the distribution services via
the wireless medium for associated clients.
LWAPP APs encapsulate all the 802.11 frames in
LWAPP frames and sends them to the controller to which
it is logically connected.
Light Weight Access Point Protocol ( LWAPP )
This is a generic protocol that defines the
communication between the Access Points and the
Central Controller.
Mobile Node ( MN )
A roaming 802.11 wireless device in a wireless
network associated with an access point. Mobile Node
and client are used interchangeably.
Extensible Authentication Protocol ( EAP )
EAP is a universal authentication protocol used in
wireless and PPP networks. It is defined by RFC 3748.
EAP-Flexible Authentication ( EAP-FAST )
This protocol is used via secure tunneling for 802.1X EAP.
PAC
PAC (Protected Access Credential) is a meachanism for
mutual authentication in EAP-FAST.
REFERENCE
[1] Wireless LAN Medium Access Control ( MAC ) and
Physical Layer ( PHY ) Specifications.
[2] Draft-obara-capwap-lwapp-00.txt, IETF Light
Weight Access Point Protocol.
[3] IEEE 802.1X - Authentication for Wireless and
Wired Connections. MODULE-IDENTITY .1.3.6.1.4.1.9.9.618 |
ciscoLwappSysMIBNotifs OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.0 |
ciscoLwappSysInvalidXmlConfigThis notification will be sent whenever invalid
configuration detected by XML NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.618.0.1 |
ciscoLwappNoVlanConfiguredThis notification will be sent whenever wired client
tries to associate without interface for specified vlan NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.618.0.2 |
ciscoLwappStrongPwdCheckThis notification will be sent whenever the management
user enables/disables the strong password rules. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.618.0.3 |
ciscoLwappSysCpuUsageHighWhen a WLC detects its CPU usage is higher than the
threshold configured in clsSysControllerCpuUsageThreshold,
this notification is generated with clsSysAlarmSet set
to true. When its CPU usage falls below the threshold
lately, this notification is generated with
clsSysAlarmSet set to false. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.618.0.4 |
ciscoLwappSysMemoryUsageHighWhen a WLC detects its memory usage is higher than the
threshold configured in clsSysControllerMemoryUsageThreshold,
this notification is generated with clsSysAlarmSet set
to true. When its memory usage falls below the threshold
lately, this notification is generated with
clsSysAlarmSet set to false. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.618.0.5 |
ciscoLwappMaxRFIDTagsReachedThis notification is generated when the number of
RFID tags on the controller exceeds the limit defined by
clsMaxRFIDTagsTrapThreshold. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.618.0.6 |
ciscoLwappMaxClientsReachedThis notification is generated when the number of
clients on the controller exceeds the limit defined by
clsMaxClientsTrapThreshold. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.618.0.7 |
ciscoLwappNMHeartBeatThis notification will be sent when Network Mamager
Heart Beat Enable. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.618.0.8 |
ciscoLwappSysMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.1 |
clsConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.1.1 |
clsDot3BridgeEnabledThis object specifies whether 803.2 bridging
mode is enabled or disabled on the controller.
A value of 'true' specifies that the bridging
mode is enabled. A value of 'false' specifies
that the bridging mode is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.1.1 |
clsConfigDownload OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.1.1.2 |
clsDownloadFileTypeThis object specifies the file types that
can be downloaded to the controller.
The file types for download are:
unknown - Unknown file type
code - Code file
config - Configuration file
webAuthCert - Web authentication certificates
webAdminCert - Web administrative certificates
signatures - Signature file
customWebAuth - Custom web authentication
tar file
vendorDeviceCert - Vendor device certificates
vendorCaCert - Vendor certificate authority
certificatesrw Enumeration .1.3.6.1.4.1.9.9.618.1.1.2.1 |
clsDownloadCertificateKeyThis object specifies the key used
to encrypt the EAP certificate, specified
by IEEE 802.1X standard, during upload from
the controller and for decrypting the file
after its downloaded to the controller.
This object is relevant only when
clsDownloadFileType is 'vendorDeviceCert'.
For all other values of clsDownloadFileType
object this will return an empty string.rw SnmpAdminString .1.3.6.1.4.1.9.9.618.1.1.2.2 |
clsConfigUpload OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.1.1.3 |
clsUploadFileTypeThis object specifies the file types that
can be uploaded to the controller.
The file types for upload are:
unknown - Unknown file
config - Configuration file
errorLog - Error log
systemTrace - System trace
trapLog - Trap log
crashFile - Crash file
signatures - Signature file
pac - PAC file
radioCoreDump - AP's Radio core dump file
invalidConfig - Upload the file which contains the
invalid configuration commands feeded
by the downloaded Config file.
debugfile - Debug file.
pktCapture - Packet Capture File
watchdogCrash - Watchdog Crash Information File
panicCrash - Panic Crash Information File.
vendorDevCert - EAP ca certificate.
vendorCaCert - EAP dev certificate.
webAdminCert - Web Admin certificate.
webAuthCert - Web Auth certificate.rw Enumeration .1.3.6.1.4.1.9.9.618.1.1.3.1 |
clsUploadPacUsernameThis object specifies the upload user name
for protected access credential (PAC). This
object needs to be set before setting
clsUploadFileType to 'pac'. For all other
values of clsUploadFileType this will return
an empty string.rw SnmpAdminString .1.3.6.1.4.1.9.9.618.1.1.3.2 |
clsUploadPacPasswordThis object specifies the upload password for
protected access credential (PAC). This object
needs to be set before setting clsUploadFileType
to 'pac'. For all other values of
clsUploadFileType this will return an empty
string.rw SnmpAdminString .1.3.6.1.4.1.9.9.618.1.1.3.3 |
clsUploadPacValidityThis object specifies the upload validity in
days for protected access credential (PAC).
This object is relevant only when
clsUploadFileType is set to 'pac'.
For all other values of clsUploadFileType
this will return an empty string.rw Unsigned32 .1.3.6.1.4.1.9.9.618.1.1.3.4 |
clsTransferConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.1.1.4 |
clsTransferConfigFileEncryptionThe configuration file can be encrypted before
upload from the controller and then decrypted
before downloading to the controller when this
option is enabled.
This is applicable only when clsDownloadFileType,
clsUploadFileType is set to Config.rw Enumeration .1.3.6.1.4.1.9.9.618.1.1.4.1 |
clsTransferConfigFileEncryptionKeyThis is the key to be used when encrypting the
configuration file while upload from the controller
or while decrypting the file after download to
the controller.
This is applicable only when clsDownloadFileType,
clsUploadFileType is set to Config.rw SnmpAdminString .1.3.6.1.4.1.9.9.618.1.1.4.2 |
clsConfigGeneral OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.1.1.5 |
clsTimeZoneThis object timezone for the controller.
Enter the timezone location index.
1. (GMT-12:00) International Date Line West
2. (GMT-11:00) Samoa
3. (GMT-10:00) Hawaii
4. (GMT -9:00) Alaska
5. (GMT -8:00) Pacific Time (US and Canada)
6. (GMT -7:00) Mountain Time (US and Canada)
7. (GMT -6:00) Central Time (US and Canada)
8. (GMT -5:00) Eastern Time (US and Canada)
9. (GMT -4:00) Altantic Time (Canada)
10. (GMT -3:00) Buenos Aires (Agentina)
11. (GMT -2:00) Mid-Atlantic
12. (GMT -1:00) Azores
13. (GMT) London, Lisbon, Dublin, Edinburgh
14. (GMT +1:00) Amsterdam, Berlin, Rome, Vienna
15. (GMT +2:00) Jerusalem
16. (GMT +3:00) Baghdad
17. (GMT +4:00) Muscat, Abu Dhabi
18. (GMT +4:30) Kabul
19. (GMT +5:00) Karachi, Islamabad, Tashkent
20. (GMT +5:30) Colombo, Kolkata, Mumbai, New Delhi
21. (GMT +5:45) Katmandu
22. (GMT +6:00) Almaty, Novosibirsk
23. (GMT +6:30) Rangoon
24. (GMT +7:00) Saigon, Hanoi, Bangkok, Jakatar
25. (GMT +8:00) HongKong, Bejing, Chongquing
26. (GMT +9:00) Tokyo, Osaka, Sapporo
27. (GMT +9:30) Darwin
28. (GMT+10:00) Sydney, Melbourne, Canberra
29. (GMT+11:00) Magadan, Solomon Is., New Caledonia
30. (GMT+12:00) Kamchatka, Marshall Is., Fijirw Unsigned32 .1.3.6.1.4.1.9.9.618.1.1.5.1 |
clsTimeZoneDescriptionThis object represents the timezone description
for the controller.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.618.1.1.5.2 |
clsMaxClientsTrapThresholdThis object specifies the threshold number
of clients on the controller to trigger a trap.
The trap ciscoLwappMaxClientsReached
will be triggered once the count of clients
on the controller reaches this limit and the
clsMaxClientsTrapEnabled is enabled.rw Unsigned32 UNITS "Percent" .1.3.6.1.4.1.9.9.618.1.1.5.3 |
clsMaxRFIDTagsTrapThresholdThis object specifies the threshold number
of RFID tags on the controller to trigger a trap.
The trap ciscoLwappMaxRFIDTagsReached
will be triggered once the count of RFID tags
on the controller reaches this limit and the
clsMaxRFIDTagsTrapEnabled is enabled.rw Unsigned32 UNITS "Percent" .1.3.6.1.4.1.9.9.618.1.1.5.4 |
clsSyslogIpConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.1.1.6 |
cLSysLogConfigTableThis table is used to configure multiple syslog servers
to which the the syslog messages will be sent to by the
controller. SEQUENCE OF CLSysLogConfigEntry .1.3.6.1.4.1.9.9.618.1.1.6.1 |
cLSysLogConfigEntryEach entry in this table provides information about
the host to which the syslog messages will be sent to. CLSysLogConfigEntry .1.3.6.1.4.1.9.9.618.1.1.6.1.1 |
cLSysLogServerIndexThis object represents the index of the host to
which syslog messages will be sent. Unsigned32 .1.3.6.1.4.1.9.9.618.1.1.6.1.1.1 |
cLSysLogAddressTypeThis object represents the address type of
the host to which syslog messages will be sent.
'dns' is used when the hostname of the server
is configured.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.618.1.1.6.1.1.2 |
cLSysLogAddressThis object represents the ipaddress or hostname
of the host to which syslog messages will be sent.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.618.1.1.6.1.1.3 |
cLSysLogHostRowStatusThis is the status column for this row and is used
to create and delete specific instances of rows in
this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.1.6.1.1.4 |
cLSysArpUnicastEnabledThis object specifies whether ARP unicast
is enabled or disabled on the controller.
A value of 'true' specifies that the ARP
unicast is enabled. A value of 'false' specifies
that the ARP unicast is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.1.7 |
clsTransferConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.1.1.8 |
clsTransferConfigTableThis table is used to configure the server details
which will be used
by the controller to upload/download files. SEQUENCE OF ClsTransferConfigEntry .1.3.6.1.4.1.9.9.618.1.1.8.1 |
clsTransferConfigEntryEach entry in this table provides information about
the server to which the controller will
upload/download files. ClsTransferConfigEntry .1.3.6.1.4.1.9.9.618.1.1.8.1.1 |
clsTransferTypeTransfer type configures the type of operation
with the server by the controller. The mode is
either Upload or Download. Enumeration .1.3.6.1.4.1.9.9.618.1.1.8.1.1.1 |
clsTransferModeTransfer mode configures the mode of transfer used
by the controller with the server. The mode is
either TFTP or FTP/SFTP. Enumeration .1.3.6.1.4.1.9.9.618.1.1.8.1.1.2 |
clsTransferServerAddressTypeThis object represents the address type of
the Server to which the controller will transfer the file.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.618.1.1.8.1.1.3 |
clsTransferServerAddressThis object represents the address of the Server to
which the controller will transfer the file.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.618.1.1.8.1.1.4 |
clsTransferPathTransfer path configures the directory
path for file transfer. The controller
remembers the last file path used.rw SnmpAdminString .1.3.6.1.4.1.9.9.618.1.1.8.1.1.5 |
clsTransferFilenameTransfer filename configures the file name for the
file being transferred from the controller.
The controller remembers the last file
name used. An example would be File Path
set to c:\tftp\code\ and File Name set to
e1r1v1.opr.rw SnmpAdminString .1.3.6.1.4.1.9.9.618.1.1.8.1.1.6 |
clsTransferFtpUsernameThis object is used to store the FTP username for
transferring file on the server.
This is valid only for FTP transfer mode.rw SnmpAdminString .1.3.6.1.4.1.9.9.618.1.1.8.1.1.7 |
clsTransferFtpPasswordThis object is used to store the FTP password for
transferring file on the server.
This is valid only for FTP transfer mode.rw SnmpAdminString .1.3.6.1.4.1.9.9.618.1.1.8.1.1.8 |
clsTransferFtpPortNumThis object is used to store the port number to be used
by the FTP protocol while connecting to the server.
This is valid only for FTP transfer mode.rw InetPortNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.618.1.1.8.1.1.9 |
clsTransferTftpMaxRetriesMaximum number of retries to be allowed for a
TFTP message packet.
This is valid only for TFTP transfer mode.rw Unsigned32 .1.3.6.1.4.1.9.9.618.1.1.8.1.1.10 |
clsTransferTftpTimeoutTimeout in seconds for a TFTP message packet.
This is valid only for TFTP transfer mode.rw Unsigned32 .1.3.6.1.4.1.9.9.618.1.1.8.1.1.11 |
clsTransferStartTransfer start will start the file transfer operation
on Active when it is set to initiate(2), it will
return none(1) for GET. Transfer start will start
the file transfer operation on Standby when it
is set to initiatePeer(3),rw Enumeration .1.3.6.1.4.1.9.9.618.1.1.8.1.1.12 |
clsTransferStatusIndicates the current status of a transfer.
Following are valid only when clsTransferType
is 'download' :-
bootBreakOff(14), invalidTarFile(15).ro Enumeration .1.3.6.1.4.1.9.9.618.1.1.8.1.1.13 |
clsTransferStatusStringIndicates in string format about the current
status of a transfer.ro SnmpAdminString .1.3.6.1.4.1.9.9.618.1.1.8.1.1.14 |
cLSysBroadcastForwardingEnabledThis object specifies whether broadcast forwarding
is enabled or disabled on the controller.
A value of 'true' specifies that the broadcast
forwarding is enabled. A value of 'false' specifies
that the broadcast forwarding is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.1.9 |
cLSysLagModeEnabledThis object specifies whether Link Aggregation(LAG)
mode is enabled or disabled on the controller.
A value of 'true' specifies that the LAG mode
is enabled. A value of 'false' specifies
that the LAG mode is disabled on the controller.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.1.10 |
clsConfigProductBranchVersionThis string contains the branch name of the specific
controller branch. For Mesh branches, this string has
the value M(Mesh). Zero length string is returned if
there is no branch name. This string is append to the
product version for display purposes. For example,
if the mesh product version is 4.1.191.10, a manager
application may display the version string as
4.1.191.10M (Mesh)ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.1.11 |
clsConfigDhcpProxyEnabledThis object represents whether the DHCP proxy option is
enabled or disabled.
A value of 'true' specifies that the proxy option is enabled
on the controller.
A value of 'false' specifies that the proxy option
is disabled on the controller.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.1.12 |
cLSysMulticastIGMP OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.1.1.13 |
cLSysMulticastIGMPSnoopingEnabledThis object specifies whether Multicast IGMP
Snooping is enabled or disabled on the controller.
A value of 'true' specifies that
the Multicast IGMP Snooping is enabled. To enable this,
agentNetworkMulticastMode/clsConfigMulticastEnabled must
not be in disabled state. A value of 'false'
specifies that the Multicast IGMP Snooping is
disabled on the controller.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.1.13.1 |
cLSysMulticastIGMPSnoopingTimeoutThis object specifies the IGMP timeout, in seconds.
To set this value, cLSysMulticastIGMPSnoopingEnabled
must be set to True. When the timeout expires,
the controller sends a query on all WLANs, causing
all clients that are listening to a multicast group
to send a packet back to the controller.rw Unsigned32 UNITS "Seconds" .1.3.6.1.4.1.9.9.618.1.1.13.2 |
cLSysMulticastIGMPQueryIntervalThis object specifies the IGMP query interval, in seconds.
To set this value, cLSysMulticastIGMPSnoopingEnabled must
be set to True.rw Unsigned32 UNITS "Seconds" .1.3.6.1.4.1.9.9.618.1.1.13.3 |
cLSPortModeConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.1.1.14 |
clsPortModeConfigTableThis table contains the entries for physical
port related parameters SEQUENCE OF ClsPortModeConfigEntry .1.3.6.1.4.1.9.9.618.1.1.14.1 |
clsPortModeConfigEntryThis entry contains the Switch's physical
port phyical mode related attribues ClsPortModeConfigEntry .1.3.6.1.4.1.9.9.618.1.1.14.1.1 |
clsPortDot1dBasePortThis object is a unique unsigned integer value which identifies
the base port number. Unsigned32 .1.3.6.1.4.1.9.9.618.1.1.14.1.1.1 |
clsPortModePhysicalModeThe switch's Port Speed Mode. This is the
configured physical mode.rw Enumeration .1.3.6.1.4.1.9.9.618.1.1.14.1.1.2 |
clsPortModePhysicalStatusThe switch's Port Physical Speed Status.This
is the current actual speed.ro Enumeration .1.3.6.1.4.1.9.9.618.1.1.14.1.1.3 |
clsPortModeSfpTypeThis object represents the SFP's type
of the port.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.618.1.1.14.1.1.4 |
clsPortUpDownCountThis object represents the total number
of up/down count of the port. Every time
the value of ifOperStatus is changed,
this MIB should be incremented.ro Counter32 .1.3.6.1.4.1.9.9.618.1.1.14.1.1.5 |
clsCoreDump OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.1.1.15 |
clsCoreDumpTransferEnableThis object specifies whether the core dump
file transfer is enabled or disabled. If the
value is True the core-dump feature is Enabled
otherwise Disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.1.15.1 |
clsCoreDumpTransferModeThis Object specifies the Core Dump Transfer Mode.
If the value is FTP then only FTP attributes
clsCoreDumpServerIPAddress, clsCoreDumpFileName,
clsCoreDumpUserName, clsCoreDumpPassword can be set,
unknown value is not SETable.rw Enumeration .1.3.6.1.4.1.9.9.618.1.1.15.2 |
clsCoreDumpServerIPAddressTypeThis Object Id Specifies the IP Address Type of Server.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.618.1.1.15.3 |
clsCoreDumpServerIPAddressThis object specifies the IP Address of the Server
where the core-dump will be uploaded.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.618.1.1.15.4 |
clsCoreDumpFileNameThis object specifies the File Name of the core-dump by
which you want to save it on the
Server.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.618.1.1.15.5 |
clsCoreDumpUserNameThis object specifies the Login Name at the FTP server.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.618.1.1.15.6 |
clsCoreDumpPasswordThis object specifies the Login Password of the FTP server.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.618.1.1.15.7 |
clsConfigMulticastEnabledThis object represents whether global multicast is
enabled or disabled.
A value of 'true' specifies that the multicast option
is enabled on the controller.
A value of 'false' specifies that the multicast option
is disabled on the controller.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.1.16 |
cLSysMulticastMLD OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.1.1.17 |
cLSysMulticastMLDSnoopingEnabledThis object specifies whether Multicast MLD Snooping
is enabled or disabled on the controller. A value of
'true' specifies that the Multicast MLD Snooping is
enabled. To enable this, agentNetworkMulticastMode/
clsConfigMulticastEnabled must not be
in disabled state. A value of 'false' specifies
that the Multicast MLD Snooping is disabled
on the controller.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.1.17.1 |
cLSysMulticastMLDSnoopingTimeoutThis object specifies the MLD timeout, in seconds.
To set this value, cLSysMulticastMLDSnoopingEnabled
must be set to True. When the timeout expires,
the controller sends a query on all WLANs, causing all
clients that are listening to a multicast group
to send a packet back to the controller.rw Unsigned32 UNITS "Seconds" .1.3.6.1.4.1.9.9.618.1.1.17.2 |
cLSysMulticastMLDQueryIntervalThis object specifies the MLD query interval, in seconds.
To set this value, cLSysMulticastMLDSnoopingEnabled
must be set to True.rw Unsigned32 UNITS "Seconds" .1.3.6.1.4.1.9.9.618.1.1.17.3 |
clsConfigStats OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.1.1.18 |
clsSysRealtimeStatsTimerThis object specifies the realtime stats interval
of the system. There are 2 stats modes: realtime and
normal. realtime interval is much less than normal mode.rw Unsigned32 .1.3.6.1.4.1.9.9.618.1.1.18.1 |
clsSysNormalStatsTimerThis object specifies the normal stats interval
of the system. There are 2 stats modes: realtime
and normal. realtime interval is much less than
normal mode.rw Unsigned32 .1.3.6.1.4.1.9.9.618.1.1.18.2 |
clsSysStatsSamplingIntervalThis object specifies the sampling interval of the system,
which is applied to WLC and APs connected to this WLC.
WLC and APs poll specific data every sampling interval.rw Unsigned32 UNITS "Seconds" .1.3.6.1.4.1.9.9.618.1.1.18.3 |
clsSysStatsAverageIntervalThis object specifies the average statistics interval of
the system, which is applied to WLC and APs connected to
this WLC. This interval works as a time window for
calculating the average value of the data polled by WLC/AP
every sampling interval.rw Unsigned32 UNITS "Seconds" .1.3.6.1.4.1.9.9.618.1.1.18.4 |
clsAlarmObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.1.1.19 |
clsAlarmHoldTimeThis object specifies the time in seconds for which
an alarm object should be soaked when its on/off
state is changed.rw Unsigned32 .1.3.6.1.4.1.9.9.618.1.1.19.1 |
clsAlarmTrapRetransmitIntervalThis object specifies the interval in seconds in
which alarm traps, if any, are retransmitted.
Setting this value to 0 means no retransmission.rw Unsigned32 .1.3.6.1.4.1.9.9.618.1.1.19.2 |
clsSysThresholdConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.1.1.20 |
clsSysControllerCpuUsageThresholdThis object specifies the CPU usage threshold on a
controller.
Setting this value to 0 means no threshold.rw Unsigned32 .1.3.6.1.4.1.9.9.618.1.1.20.1 |
clsSysControllerMemoryUsageThresholdThis object specifies the memory usage threshold on a
controller.
Setting this value to 0 means no threshold.rw Unsigned32 .1.3.6.1.4.1.9.9.618.1.1.20.2 |
clsSysApCpuUsageThresholdThis object specifies the CPU usage threshold on a
AP.
Setting this value to 0 means no threshold.rw Unsigned32 .1.3.6.1.4.1.9.9.618.1.1.20.3 |
clsSysApMemoryUsageThresholdThis object specifies the memory usage threshold on a
AP.
Setting this value to 0 means no threshold.rw Unsigned32 .1.3.6.1.4.1.9.9.618.1.1.20.4 |
clsNMHeartBeat OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.1.1.21 |
clsNMHeartBeatEnableThis object specifies whether heart beat trap to network
manager is enabled or disabled. If the value is True the
Network Manager Heart Beat feature is Enabled otherwise
Disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.1.21.1 |
clsNMHeartBeatIntervalThis object specifies the interval in seconds in heart beat
traps to network manager.rw Unsigned32 .1.3.6.1.4.1.9.9.618.1.1.21.2 |
clsCrashSystemThis object resets the switch with a crash.
If a value of of 'true' is set, the swicth would crash.
GET on this object would return 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.1.99 |
clsStatus OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.1.2 |
cLSysLagModeInTransitionThis object specifies whether the LAG mode is
in transition on the controller.
A value of 'true' specifies that the LAG mode
is in transition and the controller has to be rebooted
to take effect.A value of 'false' specifies
that the LAG mode is not in transition.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.2.1 |
clsImageInfo OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.1.3 |
clsEmergencyImageVersionCisco recommends installing Cisco Unified Wireless Network
Controller Boot Software , (*_ER.aes , where star denotes
the version of the controller image ) on all controller
platforms. If this ER.aes is not installed, the controller
would not be able to show the Emergency Image Version
correctly(or Field Recovery Image Version), and would be shown
as 'N/A'. The ER.aes files are independent from the controller
software files. Any controller software file can be run
with any ER.aes file. However, installing the latest boot
software file (*_ER.aes , where star denotes the controller
version) ensures that the boot software modifications in
all of the previous and current
boot software ER.aes files are installed.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.3.1 |
clsCpuInfo OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.1.4 |
clsAllCpuUsageThis object specifies the CPU usage string.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.4.1 |
clsSecurityGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.1.5 |
clsSecStrongPwdCaseCheckThis object is used to enable/disable the case check for the
passwords configured in controller.
When enabled, the new password must contain characters from
at least three of the following classes : lowercase letters,
uppercase letters, digits and special characters.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.5.1 |
clsSecStrongPwdConsecutiveCheckThis object is used to enable/disable the consecutive
check for the passwords configured in controller.
When enabled, the password provided should not have
a character repeated more than thrice consecutively.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.5.2 |
clsSecStrongPwdDefaultCheckThis object is used to enable/disable the default check
for the passwords configured in controller.
When enabled, the new password must not be 'cisco',
'ocsic', 'admin', 'nimda' or any variant obtained by
changing the capitalization of letters therein,
or by substituting '1' '|' or '!' for i, and/or
substituting '0' for 'o',
and/or substituting '$' for 's'rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.5.3 |
clsSecStrongPwdAsUserNameCheckThis object is used to enable/disable the username check
for the password configured in controller.
When enabled the new password must not be same as
the associated username or the reversed username.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.5.4 |
ciscoLwappSysMIBNotifObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.1.6 |
clsSecStrongPwdManagementUserThis object specifies the management user who
enabled/disabled the strong password checks.ro OCTET STRING .1.3.6.1.4.1.9.9.618.1.6.1 |
clsSecStrongPwdCheckTypeThis object specifies the type of the check that was
enabled/disabled by the management user.ro Enumeration .1.3.6.1.4.1.9.9.618.1.6.2 |
clsSecStrongPwdCheckOptionThis object specifies whether the strong password check
was enabled/disabled.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.6.3 |
clsSysAlarmSetThis object specifies whether this system alarm is
raise or clear.
A value of 'true' indicates this event is set.
A value of 'false' indicates this even is cleared.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.6.4 |
ciscoLwappSysMIBNotifControlObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.1.7 |
clsSecStrongPwdCheckTrapEnabledThis object specifies whether the
ciscoLwappStrongPwdCheck notification would be generated.
A value of 'true' indicates that the agent generates
ciscoLwappStrongPwdCheck notification.
A value of 'false' indicates that the agent doesn't
generate ciscoLwappStrongPwdCheck notification.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.7.1 |
clsMaxClientsTrapEnabledThis object specifies whether the
ciscoLwappMaxClientsReached notification would be generated.
A value of 'true' indicates that the agent generates
ciscoLwappMaxClientsReached notification.
A value of 'false' indicates that the agent doesn't
generate ciscoLwappMaxClientsReached notification.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.7.2 |
clsMaxRFIDTagsTrapEnabledThis object specifies whether the
ciscoLwappMaxRFIDTagsReached notification would be generated.
A value of 'true' indicates that the agent generates
ciscoLwappMaxRFIDTagsReached notification.
A value of 'false' indicates that the agent doesn't
generate ciscoLwappMaxRFIDTagsReached notification.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.7.3 |
clsSysInfo OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.1.8 |
clsSysFlashSizeThis object specifies the total flash memory size in Kbytes.ro Unsigned32 .1.3.6.1.4.1.9.9.618.1.8.1 |
clsSysMemoryTypeThis object specifies the system memory type.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.8.2 |
clsSysMaxClientsThis object specifies max associated clients
supported per WLCro Unsigned32 .1.3.6.1.4.1.9.9.618.1.8.3 |
clsSysApConnectCountThis object specifies the count of AP's that are
connected with WLCro Unsigned32 .1.3.6.1.4.1.9.9.618.1.8.4 |
clsSysNetIdThis object specifies the SysNetId which is the
numeric string to identify the system information
like SysNamerw SnmpAdminString .1.3.6.1.4.1.9.9.618.1.8.5 |
clsSysCurrentMemoryUsageThis object specifies the current percent usage
of system memory. This MIB should be updated
every clsSysStatsSamplingInterval.ro Unsigned32 .1.3.6.1.4.1.9.9.618.1.8.6 |
clsSysAverageMemoryUsageThis object specifies the average percent usage
of system memory. The memory average usage should be
the average of memory-Usage during the time window
specified by clsSysStatsAverageInterval.ro Unsigned32 .1.3.6.1.4.1.9.9.618.1.8.7 |
clsSysCurrentCpuUsageThis object specifies the current percent usage of all CPUs.
This MIB should be updated every clsSysStatsSamplingInterval.ro Unsigned32 .1.3.6.1.4.1.9.9.618.1.8.8 |
clsSysAverageCpuUsageThis object specifies the average percent CPU usage.
The average CPU usage should be the average of CPU-Usage
during the time window specified by
clsSysStatsAverageInterval.ro Unsigned32 .1.3.6.1.4.1.9.9.618.1.8.9 |
clsSysCpuTypeThis object specifies the cpu type.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.9.9.618.1.8.10 |
clsMaxRFIDTagsCountThis object represents the maximum RFID tags present
on the controller.ro Unsigned32 .1.3.6.1.4.1.9.9.618.1.8.11 |
clsMaxClientsCountThis object represents the maximum clients present
on the controller.ro Unsigned32 .1.3.6.1.4.1.9.9.618.1.8.12 |
ciscoLwappSysMIBConform OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.2 |
ciscoLwappSysMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.2.1 |
ciscoLwappSysMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.618.2.2 |