CISCO-LWAPP-MESH-MIB
AI MIB Summary
The CISCO-LWAPP-MESH-MIB enables monitoring and management of Cisco Central Controller (CC) entities within Lightweight Access Point Protocol (LWAPP) wireless mesh deployments, specifically tracking Root AP (RAP) and Mesh AP (MAP) parent-child associations, mesh backhaul link states, and node roaming events. It provides visibility into the topology and operational status of the wireless mesh sector, including signal-to-noise ratios (SNR), aggregate MAC service data unit (AMSDU) statistics, and the encapsulation of 802.11 client frames within LWAPP tunnels.
This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol (LWAPP) tunnel from Light-weight Access Points.
This MIB represents information used in Wireless Mesh Network. MAP APs associates directly with RAP APs or with another MAP AP. Each association of AP (MAP-MAP or RAP-MAP) with another AP forms parent-child relationship.
The deployment of the controller (referred to as CC in the diagram), mesh nodes (RAP and MAP) LWAPP APs, client(MS) and NMS appear as follows.
+.......+ +.......+
+ + + +
+ NMS + + NMS +
+ + + +
+.......+ +.......+
. . . . . . . . . . . . . .
+......+ +......+ +......+ +......+
+ + + + + + + +
+ CC + + CC + + CC + + CC +
+ + + + + + + +
+......+ +......+ +......+ +......+
.. . . . .. . . . . . . . . . . . . . . . . . . . . . . .
+......+ +......+ +......+ +......+ +......+
+ + + + + + + + + +
+ RAP + + RAP + + RAP + + RAP + + RAP +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
. . . . . . . . . . . . . . . . . . . . . . . . .
+......+ +......+ +......+ +......+ +......+
+ + + + + + + + + +
+ MAP + + MS + + MAP + + MAP + + MAP +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
. . .. . . . . .. . . . . .. . . . . . .
+......+ +......+ +......+ +......+. +......+
+ + + + + + + + + +
+ MAP + + MAP + + MAP + + MAP + + MS +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard.
LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters to the LWAPP APs. The APs encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller.
GLOSSARY
Access Point ( AP )
An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends them to the controller to which it is logically connected.
Central Controller ( CC )
The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity is also referred to as 'controller'.
Mobile Station ( MS )
A roaming 802.11 wireless device in a wireless network associated with an access point. Mobile Station and client are used interchangeably.
Network Management System ( NMS )
The station from which the administrator manages the wired and wireless networks.
Mesh Node
A mesh node is defined as a physical or logical entity in the mesh network participating in forming the mesh backhaul. RAP and MAP are two types of mesh nodes supported in mesh network.
Root AP (RAP)
The AP forming the bridge between a wired and a mesh network with an Ethernet interface to the wired network and a 802.11 radio interface to the mesh network
Mesh AP (MAP).
The AP extending wireless coverage similar to a repeater in a mesh network and consists of a 802.11 uplink and a 802.11 downlink. On a single-radio backhaul, both uplink and downlink exist on the same radio and are logical links only. On a multi-radio backhaul, they may exist on different radios.
Mesh Network
Network starting with the wireless backhaul downlink of the RAP and all the entities below except any attached network to the Ethernet link of MAPs. A mesh network below a single RAP is also referred to as a 'Mesh Sector'.A mesh network consists of mesh nodes. A single mesh network is always augmented to a single wired network.
Mesh Link
A logical 802.11 link between two mesh nodes. A single link is point-to-point. All point-to-multipoint links are considered as multiple mesh links. Often referred to as mesh backhaul link.
Mesh Backhaul
A mesh backhaul consists of mesh nodes and mesh links terminating at a RAP. This necessarily creates a one- to-one relationship between a 'mesh network', 'mesh sector' and a 'mesh backhaul' where these terms can be used interchangeably.
SNR
Signal to Noise ratio on the 802.11 radio.
Bridged network
The bridged network is defined as the network(s) attached to the Ethernet port of any MAP. There can be multiple such networks attached to a single mesh network.
Mesh Node Roaming
A mesh node may change its parent mesh node naturally when the RF/network condition changes. Child Mesh node will re-associate and re-authenticate to new parent mesh node. Mesh Security supports two types of mesh node roaming. Intra-controller - LWAPP session is not lost. Inter-controller - LWAPP session is lost.
AMSDU
Aggregate MAC Service Data Unit. A structure containing multiple MSDUs, transported within a single (unfragmented) or multiple (fragmented) Data MPDU.
IDS
Intrusion Detection Sysytem. A software to detect unwanted attempts at accessing,manipulating, and or disabling of WLC.
ExtendedUA
For 1524 APs, it has two 802.11a radios (slot1, slot2) and one 802.11b/g radio (slot0). This will enable the client access on 802.11a (slot1) for 152x series mesh access points with two 802.11a radios, where the wireless client association can be done over the 802.11a radio (slot1). With this feature we are providing an option to enable/disable backhaul client on another 802.11a radio (slot2) as well. This implies that a 152x series mesh access points with two 802.11a radios can carry both backhaul traffic and 802.11a (slot1, slot2) client traffic over the same radios.
REFERENCE
[1] Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications.
[2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol
Main OID:
ciscoLwappMeshMIB.1.3.6.1.4.1.9.9.616
86
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
86 total| Object Name |
|---|
ciscoLwappMeshMIBThis MIB is intended to be implemented on all those
devices operating as Central Controllers (CC) that
terminate the Light Weight Access Point Protocol
(LWAPP) tunnel from Light-weight Access Points.
This MIB represents information used in Wireless Mesh
Network. MAP APs associates directly with RAP APs or
with another MAP AP. Each association of AP (MAP-MAP
or RAP-MAP) with another AP forms parent-child
relationship.
The deployment of the controller
(referred to as CC in the diagram), mesh nodes
(RAP and MAP) LWAPP APs, client(MS) and NMS appear
as follows.
+.......+ +.......+
+ + + +
+ NMS + + NMS +
+ + + +
+.......+ +.......+
. .
. . . .
. . . .
. . . .
+......+ +......+ +......+ +......+
+ + + + + + + +
+ CC + + CC + + CC + + CC +
+ + + + + + + +
+......+ +......+ +......+ +......+
.. . . .
.. . . .
. . . . .
. . . . .
. . . . .
. . . . .
+......+ +......+ +......+ +......+ +......+
+ + + + + + + + + +
+ RAP + + RAP + + RAP + + RAP + + RAP +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
. . . . .
. . . . .
. . . . .
. . . . .
. . . . .
+......+ +......+ +......+ +......+ +......+
+ + + + + + + + + +
+ MAP + + MS + + MAP + + MAP + + MAP +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
. . .. .
. . . .. .
. . . .. .
. . . . .
+......+ +......+ +......+ +......+. +......+
+ + + + + + + + + +
+ MAP + + MAP + + MAP + + MAP + + MS +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
The LWAPP tunnel exists between the controller and
the APs. The MNs communicate with the APs through
the protocol defined by the 802.11 standard.
LWAPP APs, upon bootup, discover and join one of the
controllers and the controller pushes the
configuration, that includes the WLAN parameters to
the LWAPP APs.
The APs encapsulate all the 802.11 frames from
wireless clients inside LWAPP frames and forward
the LWAPP frames to the controller.
GLOSSARY
Access Point ( AP )
An entity that contains an 802.11 medium access
control ( MAC ) and physical layer ( PHY ) interface
and provides access to the distribution services via
the wireless medium for associated clients.
LWAPP APs encapsulate all the 802.11 frames in
LWAPP frames and sends them to the controller to which
it is logically connected.
Central Controller ( CC )
The central entity that terminates the LWAPP protocol
tunnel from the LWAPP APs. Throughout this MIB,
this entity is also referred to as 'controller'.
Mobile Station ( MS )
A roaming 802.11 wireless device in a wireless
network associated with an access point. Mobile Station
and client are used interchangeably.
Network Management System ( NMS )
The station from which the administrator manages the
wired and wireless networks.
Mesh Node
A mesh node is defined as a physical or logical entity
in the mesh network participating in forming the mesh
backhaul. RAP and MAP are two types of mesh nodes
supported in mesh network.
Root AP (RAP)
The AP forming the bridge between a wired and a mesh
network with an Ethernet interface to the wired
network and a 802.11 radio interface to the mesh
network
Mesh AP (MAP).
The AP extending wireless coverage similar to a
repeater in a mesh network and consists of a 802.11
uplink and a 802.11 downlink. On a single-radio
backhaul, both uplink and downlink exist on the same
radio and are logical links only. On a multi-radio
backhaul, they may exist on different radios.
Mesh Network
Network starting with the wireless backhaul downlink
of the RAP and all the entities below except any
attached network to the Ethernet link of MAPs. A mesh
network below a single RAP is also referred to as a
'Mesh Sector'.A mesh network consists of mesh nodes.
A single mesh network is always augmented to a single
wired network.
Mesh Link
A logical 802.11 link between two mesh nodes. A single
link is point-to-point. All point-to-multipoint links
are considered as multiple mesh links. Often referred
to as mesh backhaul link.
Mesh Backhaul
A mesh backhaul consists of mesh nodes and mesh links
terminating at a RAP. This necessarily creates a one-
to-one relationship between a 'mesh network', 'mesh
sector' and a 'mesh backhaul' where these terms can be
used interchangeably.
SNR
Signal to Noise ratio on the 802.11 radio.
Bridged network
The bridged network is defined as the network(s)
attached to the Ethernet port of any MAP. There can be
multiple such networks attached to a single mesh
network.
Mesh Node Roaming
A mesh node may change its parent mesh node naturally
when the RF/network condition changes. Child Mesh node
will re-associate and re-authenticate to new parent
mesh node. Mesh Security supports two types of mesh
node roaming.
Intra-controller - LWAPP session is not lost.
Inter-controller - LWAPP session is lost.
AMSDU
Aggregate MAC Service Data Unit. A structure containing
multiple MSDUs, transported within a single (unfragmented)
or multiple (fragmented) Data MPDU.
IDS
Intrusion Detection Sysytem. A software to detect unwanted
attempts at accessing,manipulating, and or disabling of WLC.
ExtendedUA
For 1524 APs, it has two 802.11a radios (slot1, slot2) and
one 802.11b/g radio (slot0). This will enable the client
access on 802.11a (slot1) for 152x series mesh access points
with two 802.11a radios, where the wireless client association
can be done over the 802.11a radio (slot1). With this feature
we are providing an option to enable/disable backhaul client
on another 802.11a radio (slot2) as well. This implies that
a 152x series mesh access points with two 802.11a radios
can carry both backhaul traffic and 802.11a (slot1, slot2)
client traffic over the same radios.
REFERENCE
[1] Wireless LAN Medium Access Control ( MAC ) and
Physical Layer ( PHY ) Specifications.
[2] Draft-obara-capwap-lwapp-00.txt, IETF Light
Weight Access Point Protocol MODULE-IDENTITY .1.3.6.1.4.1.9.9.616 |
ciscoLwappMeshMIBNotifs OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.616.0 |
ciscoLwappMeshAuthFailureA mesh node can fail to authorize if the MAC address
of mesh node is not in the MAC filter list or security
failure by authentication server. Reason is specified by
'clMeshAuthFailureReason'. This notification is sent by
the agent when number of failures exceeds threshold
defined by object 'clMeshMeshNodeAuthFailureThreshold'.
Object 'clMeshAuthFailureNotifEnabled' controls the
generation of this notification. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.616.0.1 |
ciscoLwappMeshChildExcludedParentThis notification will be sent by agent when child
mesh node exceeds threshold limit of number of
discovery response timeouts defined by object
'clMeshMeshChildAssociationFailuresThreshold'. The
child mesh node will not try to associate excluded
parent mesh node for the interval defined by object
'clMeshMeshChildExcludedParentInterval'.
The child mesh node will remember the excluded parent
MAC address and when it joins the network it will
inform the controller.
'cLApName' specifies child mesh node name. Child MAC
address is sent as part of index. Object
'clMeshChildExcludedParentNotifEnabled' controls the
generation of this notification. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.616.0.2 |
ciscoLwappMeshParentChangeThis notification is sent by the agent when a child
mesh node changes its parent. Child mesh node will
remember its previous parent and when it joins the
network it will inform controller about change
of its parent. 'cLApName' specifies child mesh node
name. Child mesh node MAC address is sent as part of
index. Object 'clMeshParentChangeNotifEnabled' controls
the generation of this notification. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.616.0.3 |
ciscoLwappMeshChildMovedThis notification is sent by the agent when a parent
mesh node loses connection with its child mesh node.
'cLApName' specifies parent mesh node name. Parent and
child MAC address are sent as part of index. Object
'clMeshChildMovedNotifEnabled' controls
the generation of this notification. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.616.0.4 |
ciscoLwappMeshExcessiveParentChangeThis notification is sent by the agent when child
mesh node changes its parent frequently. Each
mesh node keeps count of number of parent changes
in fixed time. If it exceeds the threshold defined
by 'clMeshExcessiveParentChangeThreshold' then child
mesh node informs the controller. 'cLApName' specifies
child mesh node name. Child and Parent MAC address are
sent as part of index. Object
'clMeshExcessiveParentChangeNotifEnabled' controls
the generation of this notification. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.616.0.5 |
ciscoLwappMeshOnsetSNRThis notification is sent by the agent when child
mesh node detects lower SNR on backhaul link then
defined by object 'clMeshSNRThresholdOnset'. SNR
value is checked after interval defined by object
'clMeshSNRCheckTimeInterval'.
'ciscoLwappMeshAbateSNR' notification will be sent
to clear this notification. 'cLApName' specifies
child mesh node name. Child and parent MAC address
are sent as part of index. Object
'clMeshPoorSNRNotifEnabled' controls the generation
of this notification. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.616.0.6 |
ciscoLwappMeshAbateSNRThis notification is sent by the agent to clear
'ciscoLwappMeshOnsetSNR' notification when child mesh
node detects SNR on backhaul link is higher then
the object defined by 'clMeshSNRThresholdAbate'. SNR
value is checked after interval defined by object
'clMeshSNRCheckTimeInterval'.
'cLApName' specifies child mesh node name.
Child and parent MAC address are sent as part of index.
Object 'clMeshPoorSNRNotifEnabled' controls the
generation of this notification. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.616.0.7 |
ciscoLwappMeshConsoleLoginThis notification is sent by the agent when login on
MAP console is successful or failure after three
attempts. 'cLApName' specifies mesh node name.
Object 'clMeshConsoleLoginNotifEnabled' controls the
generation of this notification. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.616.0.8 |
ciscoLwappMeshDefaultBridgeGroupNameThis notification is sent by the agent when MAP
mesh node joins parent using 'default' bridge
group name. The child node mac address is sent as the
index of cLApName. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.616.0.9 |
ciscoLwappMeshExcessiveHopCountThis notification is sent by the agent when the number of hops
from the MAP node to the RAP exceeds the threshold defined by
'clMeshExcessiveHopCountThreshold'. The MAP MAC address is
sent as part of the index. These alarms are raised once in three
minutes, the periodicity of AP sending the statistics to
WLC. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.616.0.10 |
ciscoLwappMeshExcessiveChildrenThis notification is sent by the agent when the child count
exceeds clMeshExcessiveRapChildThreshold for a RAP and
clMeshExcessiveMapChildThreshold for a MAP. The node MAC address
is sent as a part of the index. These alarms are raised once in
three minutes, the periodicity of AP sending the
statistics to WLC. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.616.0.11 |
ciscoLwappMeshOnsetHighSNRThis notification is sent by the agent when child
mesh node detects higher SNR on backhaul link then
defined by object 'clMeshHighSNRThresholdOnset'. SNR
value is checked after interval defined by object
'clMeshSNRCheckTimeInterval'.
'ciscoLwappMeshAbateHighSNR' notification will be sent
to clear this notification. 'cLApName' specifies
child mesh node name. Child and parent MAC address
are sent as part of index. Object
'clMeshHighSNRNotifEnabled' controls the generation
of this notification. These alarms are raised once in three
minutes, the periodicity of AP sending the statistics to
WLC. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.616.0.12 |
ciscoLwappMeshAbateHighSNRThis notification is sent by the agent to clear
'ciscoLwappMeshOnsetSNR' notification when child mesh
node detects SNR on backhaul link, which is lower than
the object defined by 'clMeshHighSNRThresholdAbate'. SNR
value is checked after interval defined by object
'clMeshSNRCheckTimeInterval'.
'clMeshNeighborLinkSnr' represents the SNR value seen by this mesh
node from neighbor mesh node.
'cLApName' specifies child mesh node name.
Child and parent MAC address are sent as part of index.
Object 'clMeshHighSNRNotifEnabled' controls the
generation of this notification. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.616.0.13 |
ciscoLwappMeshMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.616.1 |
ciscoLwappMeshConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.616.1.1 |
clMeshNodeTableThis table represents information about the 802.11
LWAPP Access Points that have joined the controller
as part of a mesh network. SEQUENCE OF ClMeshNodeEntry .1.3.6.1.4.1.9.9.616.1.1.1 |
clMeshNodeEntryEach entry represents a conceptual row in this table.
An entry is created when MAP joins the controller.
The entry is removed when the mesh node lose their
association with the controller due to loss of
communication with controller or when a mesh node
is reset. ClMeshNodeEntry .1.3.6.1.4.1.9.9.616.1.1.1.1 |
clMeshNodeRoleThis object represents the role of mesh AP which has
joined the controller. See glossary section above
for detail about MAP and RAP.rw Enumeration .1.3.6.1.4.1.9.9.616.1.1.1.1.1 |
clMeshNodeGroupNameThis object represents the group name of the mesh
sector. MAP AP will join the mesh sector which has the
same group name configured on RAP AP.rw SnmpAdminString .1.3.6.1.4.1.9.9.616.1.1.1.1.2 |
clMeshNodeBackhaulThis object represents 802.11 interface type of the
backhaul link. See Mesh Link in glossary section for
more detail on backhaul link.
dot11a - 802.11a radio is used as backhaul link.
dot11b - 802.11b radio is used as backhaul link.
dot11g - 802.11g radio is used as backhaul link.ro Enumeration .1.3.6.1.4.1.9.9.616.1.1.1.1.3 |
clMeshNodeBackhaulDataRateThis object represents the rate at which packets are sent
on the backhaul link. This object has been deprecated
for clMeshNodeBHDataRate.rwdeprecated Unsigned32 UNITS "Kbps" .1.3.6.1.4.1.9.9.616.1.1.1.1.4 |
clMeshNodeEthernetBridgeA value of 'true' indicates ethernet bridging is enable
on this mesh node. A value of 'false indicates ethernet
bridging is not enable on this mesh node. Ethernet bridging
can be enabled on RAP or MAP.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.616.1.1.1.1.5 |
clMeshNodeEthernetLinkStatusThis object represents if the link is up or down on
the ethernet port of the RAP or MAP.
up - ethernet link is up.
down - ethernet link is down.ro Enumeration .1.3.6.1.4.1.9.9.616.1.1.1.1.6 |
clMeshNodePublicSafetyBackhaul4.9Ghz considered to be public safety band and is
limited to some service providers. A value of true
indicates that 4.9 Ghz can be used on backhaul link
by selecting channel on the 802.11a backhaul radio.
Since public safety is now set at the controller level
rather then at the AP level, use of this variable is deprecated,
and the global setting clMeshPublicSafetyBackhaulGlobal should be
used instead.rwdeprecated TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.616.1.1.1.1.7 |
clMeshNodeParentMacAddressThis object represents the MAC address of a parent
mesh node. In case of RAP this object will
return 0000000000000.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.9.9.616.1.1.1.1.8 |
clMeshNodeHeaterStatusThis object represents the heater status of the
mesh node.
on - heater is in operation
off - heater is not operation.ro Enumeration .1.3.6.1.4.1.9.9.616.1.1.1.1.9 |
clMeshNodeInternalTempThis object represents the internal temperature
of mesh node in celsius.ro Integer32 UNITS "degree Celsius" .1.3.6.1.4.1.9.9.616.1.1.1.1.10 |
clMeshNodeTypeThis object represents the type of mesh node.
indoor - Mesh node which is manufactured to be used
inside the building.
outdoor - Mesh node which can be used outside building
in open environment.ro Enumeration .1.3.6.1.4.1.9.9.616.1.1.1.1.11 |
clMeshNodeHopsThis object represents the number of hops a MAP mesh node
is from RAP. When the clMeshNodeRole is set to 'RAP' this
object will return a value of zero.ro Gauge32 UNITS "hops" .1.3.6.1.4.1.9.9.616.1.1.1.1.12 |
clMeshNodeChildCountThis object represents the number of children MAPs of a RAP or
a MAP.ro Gauge32 .1.3.6.1.4.1.9.9.616.1.1.1.1.13 |
clMeshNodeBackhaulRadioThis object specifies the type of radio used for backhaul access.
unknown (1) unsupported APs
dot11bg (2) The value dot11b sets the 802.11b radio as backhaul radio
dot11a (3) The value dot11a sets the 802.11a radio as backhaul radiorw Enumeration .1.3.6.1.4.1.9.9.616.1.1.1.1.14 |
clMeshNodeBHDataRateThis object represents the rate at which packets are sent
on the backhaul link. Depending on the backhaul radio type,
denoted by clMeshNodeBackhaul object, data rate will vary.
If the value of clMeshNodeBackhaul object
is 'dot11a', data rates can be one of the following
possible values.
mbps6(4)
mbps9(5)
mbps12(7)
mbps18(8)
mbps24(9)
mbps36(10)
mbps48(11)
mbps54(12)
auto(13)
Additionally following data rates are supported if 802.11a
supports 11n.
htMcs0(14)
htMcs1(15)
htMcs2(16)
htMcs3(17)
htMcs4(18)
htMcs5(19)
htMcs6(20)
htMcs7(21)
htMcs8(22)
htMcs9(23)
htMcs10(24)
htMcs11(25)
htMcs12(26)
htMcs13(27)
htMcs14(28)
htMcs15(29)
If the value of clMeshNodeBackhaul object
is 'dot11b', then data rate can be one of
the following possible values.
mbps1(1)
mbps2(2)
mbps5point5(3)
mbps11(6)
auto(13)
IIf the value of clMeshNodeBackhaul object
is 'dot11g', then data rate can be one of
the following possible values.
mbps1(1)
mbps2(2)
mbps5point5(3)
mbps6(4)
mbps9(5)
mbps11(6)
mbps12(7)
mbps18(8)
mbps24(9)
mbps36(10)
mbps48(11)
mbps54(12)
auto(13)rw Enumeration .1.3.6.1.4.1.9.9.616.1.1.1.1.15 |
ciscoLwappMeshGlobalConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.616.1.2 |
clMeshNodeRangeThis object represents the optimal distance in feet
between RAP and MAP for backhaul link without
degrading SNR value.rw Unsigned32 .1.3.6.1.4.1.9.9.616.1.2.1 |
clMeshBackhaulClientAccessThis object represents if client access is to be
enable on backhaul link. If AP has two radios,802.11a
and 802.11bg, then radio which is used as backhaul link
does not have client access. A value of 'true' indicates
client access is present on backhaul link. If AP has only
one radio then same radio is used for backhaul and client
access.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.616.1.2.2 |
clMeshMacFilterListIf this object is 'true' then any mesh node joining
controller will be authenticated against this list.
If this object is 'false' then mesh node can join
controller even if mesh node MAC address is not
in MAC filter list.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.616.1.2.3 |
clMeshMeshNodeAuthFailureThresholdThis object represents the authorization failure
threshold value. When the number of failures exceeds
this value then 'ciscoLwappMeshAuthFailure'
notification is raised.rw Unsigned32 .1.3.6.1.4.1.9.9.616.1.2.4 |
clMeshMeshChildAssociationFailuresThresholdThis object represents the number of failed association
to controller occurred through a parent mesh node.
When this values exceeds then
'ciscoLwappMeshChildExcludedParent' notification is
raised.rw Unsigned32 .1.3.6.1.4.1.9.9.616.1.2.5 |
clMeshMeshChildExcludedParentIntervalThis object represents the time interval during which
a child mesh node will exclude a parent mesh node.
During this interval child will not try to associate
the controller through the parent mesh node.rw TimeInterval .1.3.6.1.4.1.9.9.616.1.2.6 |
clMeshSNRThresholdAbateThis object represents the abate threshold value of
SNR. This threshold value is use to determine if the
SNR value seen by the child mesh node has reached
acceptable level and is use to trigger the
'ciscoLwappMeshAbateSNR' notification.rw Unsigned32 .1.3.6.1.4.1.9.9.616.1.2.7 |
clMeshSNRThresholdOnsetThis object represents the onset threshold value of
SNR. This threshold value is use to determine if the
SNR value seen by the child mesh node has reached
below unacceptable level and is use to trigger the
'ciscoLwappMeshOnsetSNR' notification.rw Unsigned32 .1.3.6.1.4.1.9.9.616.1.2.8 |
clMeshSNRCheckTimeIntervalThis object represents the time interval after which
SNR value is checked by child mesh node.rw TimeInterval .1.3.6.1.4.1.9.9.616.1.2.9 |
clMeshExcessiveParentChangeThresholdThis object represents the threshold for the number
of times a child mesh node changes its parent. If number
of parent change exceeds this value with in the time
interval defined by object
'clMeshExcessiveParentChangeInterval' then
the 'ciscoLwappMeshExcessiveParentChange' notification
is raised.rw Unsigned32 .1.3.6.1.4.1.9.9.616.1.2.10 |
clMeshExcessiveParentChangeIntervalThis object represents the time interval during which
number of times a child mesh node changes its parent
change is counted.
If number of parent change exceeds the value defined by
the object 'clMeshExcessiveParentChangeThreshold' with in
this time interval then the
'ciscoLwappMeshExcessiveParentChange' notification
is raised.rw TimeInterval .1.3.6.1.4.1.9.9.616.1.2.11 |
clMeshBackgroundScanA value of 'true' indicates the MAP mesh node
scans its neighbors on different channel other than
only its current channel on backhaul link. This scanning
helps MAP mesh node to quickly determine its new parent
on different channels.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.616.1.2.12 |
clMeshAuthenticationModeThis object represents authentication mode of RAP and
MAP mesh nodes in controller.
none - no authentication is done.
psk - pre shared key. Keys provided during manufacturing
will be used for authentication of mesh node.
eap - extensible authentication protocol is used to
authenticate mesh node. A value of 'eap' indicates,
authentication can happen by local-auth in controller
or by RADIUS server configured in controller.rw Enumeration .1.3.6.1.4.1.9.9.616.1.2.13 |
clMeshExcessiveHopCountThresholdThis object represents threshold number of hops from the
MAP node to the RAP. Crossing this value will raise the
'ciscoLwappMeshExcessiveHopCount' notification.rw Unsigned32 .1.3.6.1.4.1.9.9.616.1.2.14 |
clMeshExcessiveRapChildThresholdThis object represents threshold number of children MAPs
attached to a parent RAP. Crossing this value will raise the
'ciscoLwappMeshExcessiveChildren' notification.rw Unsigned32 .1.3.6.1.4.1.9.9.616.1.2.15 |
clMeshExcessiveMapChildThresholdThis object represents threshold number of children MAPs
attached to a parent MAP. Crossing this value will raise the
'ciscoLwappMeshExcessiveChildren' notification.rw Unsigned32 .1.3.6.1.4.1.9.9.616.1.2.16 |
clMeshHighSNRThresholdAbateThis object represents the abate threshold value of
SNR. This threshold value is used to determine if the
SNR value seen by the child mesh node has reached
below this level and is use to trigger the
'ciscoLwappMeshAbateHighSNR' notification.rw Unsigned32 .1.3.6.1.4.1.9.9.616.1.2.17 |
clMeshHighSNRThresholdOnsetThis object represents the onset threshold value of
SNR. This threshold value is use to determine if the
SNR value seen by the child mesh node has reached
above this level and is use to trigger the
'ciscoLwappMeshOnsetHighSNR' notification.rw Unsigned32 .1.3.6.1.4.1.9.9.616.1.2.18 |
clMeshPublicSafetyBackhaulGlobal4.9Ghz considered to be public safety band and is
limited to some service providers. A value of true
indicates that 4.9 Ghz can be used on backhaul link
by selecting channel on the 802.11a backhaul radio.
This setting applies at the controller level. The
prior per AP setting clMeshNodePublicSafetyBackhaul
is deprecated as a result.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.616.1.2.19 |
clMeshisAMSDUEnableThis object represents the AMSDU status.
true : Turns on AMSDU.
false : Turns off AMSDU.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.616.1.2.20 |
clMeshIsIdsEnableThis object represents the IDS status.
true : Turns on IDS feature.
false : Turns off IDS feature.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.616.1.2.21 |
clMeshIsDCAChannelsEnableThis object represents the DCA Channel status.
true : Turns on DCA feature for AP1524SB.
false : Turns off DCA feature for AP1524SB.
This is not implies for non-1524SB APs. Error will return
if it is set for non-1524SB APs.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.616.1.2.22 |
clMeshIsExtendedUAEnableThis object represents the ExtendedUA status.
true : Turns on ExtendedUA feature.
false : Turns off ExtendedUA feature.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.616.1.2.23 |
ciscoLwappMeshNeighborsStatus OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.616.1.3 |
clMeshNeighborTableThis table represents information about neighbors
of any mesh node. Neighbor AP can be on same or
different mesh sector. Any mesh node is neighbor of a
mesh node, if it can detect 802.11 signals on any
channels. Child or parent mesh node also considers as
neighbors. SEQUENCE OF ClMeshNeighborEntry .1.3.6.1.4.1.9.9.616.1.3.1 |
clMeshNeighborEntryAn (conceptual) entry in this table is created when
mesh node detects neighbor mesh nodes.
Entries are removed when the mesh node does not detect
AP as neighbor. ClMeshNeighborEntry .1.3.6.1.4.1.9.9.616.1.3.1.1 |
clMeshNeighborMacAddressThis object represents MAC address of neighbor
mesh node. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.9.9.616.1.3.1.1.1 |
clMeshNeighborTypeThis object represents type of neighbor mesh node.
parent - Neighbor mesh node is a parent mesh node
of this mesh node.
neighbor - Its a neighbor mesh node. It can be on
same or different mesh-sector.
excluded - Neighbor mesh node is excluded by this
mesh node.
child - Neighbor mesh node is child of this mesh node.
beacon - Neighbor mesh node found by passive scanning.
Default - Neighbor mesh node connected using a mismatched
bridge group namero Bits .1.3.6.1.4.1.9.9.616.1.3.1.1.2 |
clMeshNeighborLinkSnrThis object represents the SNR value seen by this mesh
node from neighbor mesh node.ro Integer32 UNITS "dB" .1.3.6.1.4.1.9.9.616.1.3.1.1.3 |
clMeshNeighborChannelThis object represents the channel on which neighbor
mesh node is operating.ro CLDot11Channel (CISCO-LWAPP-TC-MIB) .1.3.6.1.4.1.9.9.616.1.3.1.1.4 |
clMeshNeighborUpdateThis object represents when the neighbor table was last
updated. This value is represented as a instance of
sysUp time.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.9.9.616.1.3.1.1.5 |
ciscoLwappMeshNotifControlConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.616.1.4 |
clMeshAuthFailureNotifEnabledThis object controls the generation of
'ciscoLwappMeshAuthFailure' notification.
A value of 'true' indicates notification will
be generated.
A value of 'false' indicates notification will
be not be generated.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.616.1.4.1 |
clMeshChildExcludedParentNotifEnabledThis object controls the generation of
'ciscoLwappMeshChildExcludedParent' notification.
A value of 'true' indicates notification will
be generated.
A value of 'false' indicates notification will
be not be generated.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.616.1.4.2 |
clMeshParentChangeNotifEnabledThis object controls the generation of
'ciscoLwappMeshParentChange' notification.
A value of 'true' indicates notification will
be generated.
A value of 'false' indicates notification will
be not be generated.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.616.1.4.3 |
clMeshChildMovedNotifEnabledThis object controls the generation of
'ciscoLwappMeshChildMoved' notification.
A value of 'true' indicates notification will
be generated.
A value of 'false' indicates notification will
be not be generated.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.616.1.4.4 |
clMeshExcessiveParentChangeNotifEnabledThis object controls the generation of
'ciscoLwappMeshExcessiveParentChange' notification.
A value of 'true' indicates notification will
be generated.
A value of 'false' indicates notification will
be not be generated.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.616.1.4.5 |
clMeshPoorSNRNotifEnabledThis object controls the generation of
'ciscoLwappMeshOnsetSNR' and
'ciscoLwappMeshAbateSNR' notifications.
A value of 'true' indicates notification will
be generated.
A value of 'false' indicates notification will
be not be generated.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.616.1.4.6 |
clMeshConsoleLoginNotifEnabledThis object controls the generation of
'ciscoLwappMeshConsoleLogin' notification.
A value of 'true' indicates notification will
be generated.
A value of 'false' indicates notification will
not be generated.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.616.1.4.7 |
clMeshDefaultBridgeGroupNameNotifEnabledThis object controls the generation of
'ciscoLwappMeshDefaultBridgeGroupName' notification.
A value of 'true' indicates this notification will be generated.
A value of 'false' indicates this notification will not be generated.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.616.1.4.8 |
clMeshExcessiveHopCountNotifEnabledThis object controls the generation of
'ciscoLwappMeshExcessiveHopCount' notification.
A value of 'true' indicates this notification will be generated.
A value of 'false' indicates this notification will not be generated.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.616.1.4.9 |
clMeshExcessiveChildrenNotifEnabledThis object controls the generation of
'ciscoLwappMeshExcessiveChildren' notification.
A value of 'true' indicates this notification will be generated.
A value of 'false' indicates this notification will not be generated.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.616.1.4.10 |
clMeshHighSNRNotifEnabledThis object controls the generation of
'ciscoLwappMeshOnsetHighSNR' and
'ciscoLwappMeshAbateHighSNR' notifications.
A value of 'true' indicates notification will
be generated.
A value of 'false' indicates notification will
not be generated.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.616.1.4.11 |
ciscoLwappMeshMIBNotifObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.616.1.5 |
clMeshNodeMacAddressThis object specifies the MAC address
of a LWAPP AP.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.9.9.616.1.5.1 |
clMeshAuthFailureReasonThis object specifies the failure reason when
a mesh node failed to authenticate through a
controller to an Authentication Server.
notInMacFilterList - MAC address of a mesh node
is not configured in MAC filter list.
securityFailure - Authentication server sent
rejection for the mesh node.ro Enumeration .1.3.6.1.4.1.9.9.616.1.5.2 |
clMeshPreviousParentMacAddressThis object specifies the MAC address
of previous parent Mesh Node.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.9.9.616.1.5.3 |
clMeshConsoleLoginStatusThis object specifies the status of console login
at MAP mesh node.ro Enumeration .1.3.6.1.4.1.9.9.616.1.5.4 |
ciscoLwappMeshMIBConform OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.616.2 |
ciscoLwappMeshMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.616.2.1 |
ciscoLwappMeshMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.616.2.2 |