CISCO-LRE-CPE-MIB
AI MIB Summary
The CISCO-LRE-CPE-MIB enables monitoring and management of Cisco Long Reach Ethernet (LRE) Customer Premise Equipment, specifically tracking DSL/VDSL line parameters, port status, and session statistics for remote access aggregation. This module provides visibility into physical layer connectivity and data rates for LRE-based last-mile deployments where traditional Ethernet or standard DSL is unavailable.
The MIB module for the Cisco Long Reach Ethernet Customer Premise Equipment device information.
*** ABBREVIATIONS, ACRONYMS, AND SYMBOLS ***
CPE - Customer Premise Equipment DSL - Digital Subscriber Loop VDSL - Very High Speed DSL LRE - Long Reach Ethernet
Main OID:
ciscoLreCpeMIB.1.3.6.1.4.1.9.9.340
19
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
19 total| Object Name |
|---|
ciscoLreCpeMIBThe MIB module for the Cisco Long Reach Ethernet
Customer Premise Equipment device information.
*** ABBREVIATIONS, ACRONYMS, AND SYMBOLS ***
CPE - Customer Premise Equipment
DSL - Digital Subscriber Loop
VDSL - Very High Speed DSL
LRE - Long Reach Ethernet MODULE-IDENTITY .1.3.6.1.4.1.9.9.340 |
clreCpeMIBNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.340.0 |
clreCpeMIBNotificationsPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.340.0.0 |
ciscoLreCpeMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.340.1 |
clreCpeDot1dTp OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.340.1.1 |
clreCpeDot1dTpFdbTableA table that supplements the information from the BRIDGE-MIB.
The BRIDGE-MIB tracks the MAC address to switch interface
mapping in the dot1dTpFdbTable. On the long reach ethernet
switch, CPE devices connect to the switch interfaces. Each
CPE device has one or more ports. This table maps a
MAC address on the switch to an interface associated with a
CPE port. SEQUENCE OF ClreCpeDot1dTpFdbEntry .1.3.6.1.4.1.9.9.340.1.1.1 |
clreCpeDot1dTpFdbEntryAn entry that supplements the information in the
dot1dTpFdbTable table from the BRIDGE-MIB. ClreCpeDot1dTpFdbEntry .1.3.6.1.4.1.9.9.340.1.1.1.1 |
clreCpeDot1dBasePortIfIndexThe value of the instance of the ifIndex object,
define in MIB-II, for the interface corresponding
to this CPE port. The Forwarding database on the
switch tracks a MAC address and its associated
switch interface in the dot1dTpFdbTable table.
This object adds information about which port
on the CPE the MAC address was learnt on.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.9.9.340.1.1.1.1.1 |
clreCpePort OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.340.1.2 |
clreCpePortTableA list of LRE CPE port entries. The number of entries is
determined by the number of Long Reach Ethernet interfaces
(to which the CPE attaches) on the switch and the number
of Fast Ethernet ports each CPE supports. SEQUENCE OF ClreCpePortEntry .1.3.6.1.4.1.9.9.340.1.2.1 |
clreCpePortEntryEntry containing information for a particular CPE
Fast Ethernet port. The entries are created as new
CPE devices are discovered. A new CPE device is discovered
when the LRE link between that CPE device and the LRE switch
becomes operational. These entries are only valid for
ifIndexes of ifType ethernetCsmacd(6). ClreCpePortEntry .1.3.6.1.4.1.9.9.340.1.2.1.1 |
clreCpePortAdminStatusThe desired state of the CPE port. The testing(3)
state indicates that no operational packets can be
passed. When a managed system initializes, all
CPE ports start with clreCpePortAdminStatus in
the down(2) state. As a result of either explicit
management action or per configuration information
retained by the managed system, clreCpePortAdminStatus
is then changed to either the up(1) or testing(3) states
(or remains in the down(2) state).rw Enumeration .1.3.6.1.4.1.9.9.340.1.2.1.1.1 |
clreCpePortAdminSpeedThis object controls the speed of this CPE Fast Ethernet
port. When set to autoDetect(1), the CPE port negotiates
with its peer for the optimum speed, either
s10000000(10000000) or s100000000(100000000).
If the peer does not support the autoDetect(1)
capability, the CPE port speed defaults to
s10000000(10000000).rw Enumeration .1.3.6.1.4.1.9.9.340.1.2.1.1.2 |
clreCpePortAdminDuplexThis object controls the duplex of this CPE Fast Ethernet
port. When set to autoDetect(1), the CPE port negotiates
with its peer for the optimum duplex setting, either
fullDuplex(2) or halfDuplex(3). If the peer does not support
the autoDetect(1) capability, this CPE port's duplex
defaults to halfDuplex(3).rw Enumeration .1.3.6.1.4.1.9.9.340.1.2.1.1.3 |
clreCpePortAdminProtectedThis object configures a CPE Fast Ethernet port as a
protected port when its value is set to true. Data
traffic is disallowed between two CPE ports configured
as protected ports. When the value of this object is set
to false, the protected port property of this CPE port
is removed. The value of this object can be set to true
only on those CPE ports that support the protected port
function.Note that the value of this object represents
the desired state of the port. The actual state of the
port may have a different value.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.340.1.2.1.1.4 |
clreCpePortOperProtectedThe value represented by this object is the actual
protected port state of the CPE port. The object value
is true when this CPE port is configured as a protected
port. Data packets are not forwarded between two CPE
ports configured as protected ports.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.340.1.2.1.1.5 |
clreCpeMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.340.2 |
clreCpeMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.340.2.1 |
clreCpeMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.340.2.2 |