CISCO-IPSLA-VIDEO-MIB
AI MIB Summary
The CISCO-IPSLA-VIDEO-MIB module enables Cisco IOS devices to monitor and retrieve performance metrics for active IP SLA video operations, specifically populating the `cipslaLatestVideoStatsTable` and `cipslaVideoAggStatsTable` with data on video session quality and Round Trip Time (RTT). This functionality facilitates the quantitative assessment of network health and troubleshooting for real-time video traffic by configuring the operation via the `rttMonEchoAdminProtocol` object set to `videoAppl`.
IP SLA is a capability which utilizes active monitoring for network performance. It can be used for network troubleshooting, network assessment and health monitoring.
This MIB defines a collection of statistics resulting from the 'video' IP SLA operation.
The Video Statistics table names are: cipslaLatestVideoStatsTable
cipslaVideoAggStatsTable
To create the Video operation, set rttMonEchoAdminProtocol (defined in CISCO-RTTMON-MIB) object to 'videoAppl'. Once the operation has been scheduled, both cipslaLatestVideoStatsTable and cipslaVideoAggStatsTable will be populated.
Glossary:
IP SLA - Cisco IOS IP Service Level Agreements IP SLA operation - Refers to the 'video' operation supported by IP SLA. RTT - Round Trip Time
Main OID:
ciscoIpslaVideoMIB.1.3.6.1.4.1.9.9.744
72
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
72 total| Object Name |
|---|
ciscoIpslaVideoMIBIP SLA is a capability which utilizes active monitoring for
network performance. It can be used for network
troubleshooting, network assessment and health
monitoring.
This MIB defines a collection of statistics resulting
from the 'video' IP SLA operation.
The Video Statistics table names are:
cipslaLatestVideoStatsTable
cipslaVideoAggStatsTable
To create the Video operation, set rttMonEchoAdminProtocol
(defined in CISCO-RTTMON-MIB) object to 'videoAppl'. Once the
operation has been scheduled, both cipslaLatestVideoStatsTable
and cipslaVideoAggStatsTable will be populated.
Glossary:
IP SLA - Cisco IOS IP Service Level Agreements
IP SLA operation - Refers to the 'video'
operation supported by IP SLA.
RTT - Round Trip Time MODULE-IDENTITY .1.3.6.1.4.1.9.9.744 |
ciscoIpslaVideoMIBNotifs OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.744.0 |
ciscoIpslaVideoMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.744.1 |
cipslaVideoLatestOper OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.744.1.1 |
cipslaLatestVideoStatsTableThe 'video' operation sends out video streams at the
frequency specified by rttMonCtrlAdminFrequency.
This table contains the statistics calculated for the
latest video packets.
Each conceptual row in this table corresponds to an
'video' operation defined in rttMonCtrlAdminTable
and has same index as rttMonCtrlAdminTable. SEQUENCE OF IpslaVideoJitterLatestStatsEntry .1.3.6.1.4.1.9.9.744.1.1.1 |
cipslaLatestVideoStatsEntryA collection of objects that record the latest Video jitter
operation.
An entry is created only when the following
objects are valid.
- rttMonCtrlAdminRttType
- rttMonEchoAdminProtocol
The entry will start to collect data when rttMonCtrlAdminStatus
is in 'active' state. The entry will be removed when the
rttMonCtrlAdminStatus is changed to 'destroy' state. IpslaVideoJitterLatestStatsEntry .1.3.6.1.4.1.9.9.744.1.1.1.1 |
cipslaLatestVideoMinPosSDThe minimum of all positive jitter values for packets sent
from source to destination.ro Gauge32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.1.1.1.1 |
cipslaLatestVideoMaxPosSDThe maximum of all positive jitter values for packets sent
from source to destination.ro Gauge32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.1.1.1.2 |
cipslaLatestVideoNumPosSDThe number of all positive jitter values for packets
sent from source to destination.ro Gauge32 UNITS "occurrences" .1.3.6.1.4.1.9.9.744.1.1.1.1.3 |
cipslaLatestVideoSumPosSDThe sum of all positive jitter values for packets sent
source to destination. The number of such values
is stored in cipslaLatestVideoNumPosSD.ro Gauge32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.1.1.1.4 |
cipslaLatestVideoSum2PosSDThe sum of square of all positive jitter values for
packets sent from source to destination.ro Gauge32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.1.1.1.5 |
cipslaLatestVideoMinNegSDThe minimum of absolute values of all negative jitter values
for packets sent from source to destination.ro Gauge32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.1.1.1.6 |
cipslaLatestVideoMaxNegSDThe maximum of absolute values of all negative jitter values
for packets sent from source to destination.ro Gauge32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.1.1.1.7 |
cipslaLatestVideoNumNegSDThe number of all negative jitter values for packets
sent from source to destination.ro Gauge32 UNITS "occurrences" .1.3.6.1.4.1.9.9.744.1.1.1.1.8 |
cipslaLatestVideoSumNegSDThe sum of all negative jitter values for packets sent
from source to destination. The number of such values
is stored in cipslaLatestVideoNumNegSD.ro Gauge32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.1.1.1.9 |
cipslaLatestVideoSum2NegSDThe sum of square of all negative jitter values for
packets sent from source to destination.ro Gauge32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.1.1.1.10 |
cipslaLatestVideoPktLossSDThe number of packets lost when sent from source to
destination.ro Gauge32 UNITS "packets" .1.3.6.1.4.1.9.9.744.1.1.1.1.11 |
cipslaLatestVideoPktOutSeqThe number of packets arrived out of sequence.ro Gauge32 UNITS "packets" .1.3.6.1.4.1.9.9.744.1.1.1.1.12 |
cipslaLatestVideoSenseAn application specific sense code for the completion status.ro RttResponseSense (CISCO-RTTMON-TC-MIB) .1.3.6.1.4.1.9.9.744.1.1.1.1.13 |
cipslaLatestVideoOWSumSDThe sum of one way trip time from source to destination.ro Gauge32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.1.1.1.14 |
cipslaLatestVideoOWSum2SDThe sum of squares of one way trip time from source to
destination.ro Gauge32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.1.1.1.15 |
cipslaLatestVideoOWMinSDThe minimum of all one way trip time from
source to destination.ro Gauge32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.1.1.1.16 |
cipslaLatestVideoOWMaxSDThe maximum of all one way trip time from
source to destination.ro Gauge32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.1.1.1.17 |
cipslaLatestVideoNumOWSDThe number of successful one way trip time measurements from
source to destination.ro Gauge32 UNITS "packets" .1.3.6.1.4.1.9.9.744.1.1.1.1.18 |
cipslaLatestVideoAvgJitterSDThe average of positive and negative jitter values
in Source-to-Destination direction.ro Gauge32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.1.1.1.19 |
cipslaLatestVideoIAJOutInter-arrival jitter (RFC 1889) at responder.ro Gauge32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.1.1.1.20 |
cipslaLatestVideoErrSenseDescrAn sense description for the completion status
of the latest video operation.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.744.1.1.1.1.21 |
cipslaLatestVideoUnSyncRTsThe number of RTT operations that have completed with
sender and responder out of sync with NTP. The NTP sync means
the total of NTP offset on sender and responder is within
configured tolerance levelro Counter32 .1.3.6.1.4.1.9.9.744.1.1.1.1.22 |
cipslaLatestVideoOWSumSDHighThe sum of one way latency from source to destination
(high order 32 bits). The low order 32 bits are stored in
cipslaLatestVideoOWSumSD.ro Gauge32 .1.3.6.1.4.1.9.9.744.1.1.1.1.23 |
cipslaLatestVideoOWSum2SDHighThe sum of squares of one way latency from source to
destination (high order 32 bits). The low order 32 bits
are stored in cipslaLatestVideoOWSum2SD.ro Gauge32 .1.3.6.1.4.1.9.9.744.1.1.1.1.24 |
cipslaLatestVideoNTPStateA value of sync(1) means sender and responder was in sync
with NTP. The NTP sync means the total of NTP offset
on sender and responder is within configured tolerance level.ro Enumeration .1.3.6.1.4.1.9.9.744.1.1.1.1.25 |
cipslaLatestVideoIPDVAvgSDJSource to Destination IPDV average jitter according to RFC
5481.ro Gauge32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.1.1.1.26 |
cipslaLatestVideoOWAvgSDThe average latency value from source to destination.ro Gauge32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.1.1.1.27 |
cipslaLatestVideoPktLateArrivalThe number of packets that arrived after the timeout.ro Gauge32 UNITS "packets" .1.3.6.1.4.1.9.9.744.1.1.1.1.28 |
cipslaVideoStats OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.744.1.2 |
cipslaVideoAggStatsTableThe 'video' statistics table contains summarized
information of the results for a conceptual control
row. A rolling accumulated history of this information
is maintained in a series of hourly 'group(s)'.
When ipslaVideoAggStartTimeId groups exceeds
the rttMonStatisticsAdminNumHourGroups value, the
oldest corresponding hourly group will be deleted and will
be replaced with the new ipslaVideoAggStatsStartTimeId
hourly group. SEQUENCE OF CipslaVideoAggStatsEntry .1.3.6.1.4.1.9.9.744.1.2.1 |
cipslaVideoAggStatsEntryThis entry contains the objects which accumulate the
results of a series of 'video' operations
over a 60 minute time period or a time period stored
in rttMonScheduleAdminRttLife, whichever is smaller.
An entry is created only if when the following
objects are valid.
- rttMonCtrlAdminRttType
- rttMonEchoAdminProtocol
The entry will start to collect data when rttMonCtrlAdminStatus
is in 'active' state. The entry will be removed when the
rttMonCtrlAdminStatus is changed to 'destroy' state.
cipslaVideoAggStartTimeId will be created at the beginning of
the
hour and will keep aggregating statistics until the end of the
hour. CipslaVideoAggStatsEntry .1.3.6.1.4.1.9.9.744.1.2.1.1 |
cipslaVideoAggStartTimeIdThe value of sysUpTime at the time when this
row was created. TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.9.9.744.1.2.1.1.1 |
cipslaVideoAggCompletionsThe number of video operations that have completed
successfully.ro Counter32 UNITS "completions" .1.3.6.1.4.1.9.9.744.1.2.1.1.2 |
cipslaVideoAggOverThresholdsThe number of video operations that violate
jitterAvg threshold which is defined in RttMonReactVar.ro Counter32 UNITS "operations" .1.3.6.1.4.1.9.9.744.1.2.1.1.3 |
cipslaVideoAggMinPosSDThe minimum of absolute values of all positive jitter values
for packets sent from source to destination.ro Gauge32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.2.1.1.4 |
cipslaVideoAggMaxPosSDThe maximum of absolute values of all positive jitter values
for packets sent from source to destination.ro Gauge32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.2.1.1.5 |
cipslaVideoAggNumPosSDThe number of all positive jitter values for packets
sent from source to destination.ro Counter32 UNITS "occurrences" .1.3.6.1.4.1.9.9.744.1.2.1.1.6 |
cipslaVideoAggSumPosSDThe sum of all positive jitter values for packets sent
from source to destination. The number of such values
is stored in ipslaVideoAggNumPosSDs.ro Counter32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.2.1.1.7 |
cipslaVideoAggSum2PosSDLowThe sum of square of all positive jitter values for packets
sent from source to destination (low order 32 bits).ro Counter32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.2.1.1.8 |
cipslaVideoAggSum2PosSDHighThe sum of square of all positive jitter values for packets
sent from source to destination (high order 32 bits).ro Counter32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.2.1.1.9 |
cipslaVideoAggMinNegSDThe minimum of all negative jitter values for packets sent
from source to destination.ro Gauge32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.2.1.1.10 |
cipslaVideoAggMaxNegSDThe maximum of all negative jitter values for packets sent
from source to destination.ro Gauge32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.2.1.1.11 |
cipslaVideoAggNumNegSDThe number of all negative jitter values for packets
sent from source to destination.ro Counter32 UNITS "occurrences" .1.3.6.1.4.1.9.9.744.1.2.1.1.12 |
cipslaVideoAggSumNegSDThe sum of all negative jitter values for packets sent
from source to destination. The number of such values
is stored in ipslaVideoAggNumNegSDs.ro Counter32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.2.1.1.13 |
cipslaVideoAggSum2NegSDLowThe sum of square of all negative jitter values for
packets sent from source to destination (low order 32 bits).ro Counter32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.2.1.1.14 |
cipslaVideoAggSum2NegSDHighThe sum of square of all negative jitter values for
packets sent from source to destination (high order 32 bits).ro Counter32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.2.1.1.15 |
cipslaVideoAggPktLossSDThe number of lost packets when sent from source to
destination.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.744.1.2.1.1.16 |
cipslaVideoAggPktOutSeqThe number of packets arrived out of sequence.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.744.1.2.1.1.17 |
cipslaVideoAggPktSkippedThe number of packets that are skipped per operation because
the router could not send the packet out.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.744.1.2.1.1.18 |
cipslaVideoAggErrorsThe number of occasions when a video operation could
not be initiated because of an internal error.ro Counter32 UNITS "errors" .1.3.6.1.4.1.9.9.744.1.2.1.1.19 |
cipslaVideoAggBusiesThe number of occasions when a video operation could
not be initiated because a previous video operation
has not been completed.ro Counter32 UNITS "busies" .1.3.6.1.4.1.9.9.744.1.2.1.1.20 |
cipslaVideoAggOWSumSDThe sum of one way trip time from source to destination.ro Counter32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.2.1.1.21 |
cipslaVideoAggOWSum2SDLowThe sum of squares of one way trip time from source to
destination (low order 32 bits).ro Counter32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.2.1.1.22 |
cipslaVideoAggOWSum2SDHighThe sum of squares of one way trip time from source to
destination (high order 32 bits).ro Counter32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.2.1.1.23 |
cipslaVideoAggOWMinSDThe minimum of all one way trip time from source to
destination.ro Gauge32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.2.1.1.24 |
cipslaVideoAggOWMaxSDThe maximum of all one way trip time from source to
destination.ro Gauge32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.2.1.1.25 |
cipslaVideoAggNumOWSDThe number of one way trip time that are successfully
measured from source to destination.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.744.1.2.1.1.26 |
cipslaVideoAggAvgJSDThe average of positive and negative jitter
values in source-to-destination direction.ro Gauge32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.2.1.1.27 |
cipslaVideoAggIAJOutInter-arrival jitter (RFC 1889) at responderro Gauge32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.2.1.1.28 |
cipslaVideoAggIAJInInter-arrival jitter (RFC 1889) at senderro Gauge32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.744.1.2.1.1.29 |
cipslaVideoAggPktLateArrivalThe number of packets that arrived after the timeout.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.744.1.2.1.1.30 |
cipslaVideoAggUnSyncRTsThe number of RTT operations that have completed with
sender and responder out of sync with NTP. The NTP sync means
the total of NTP offset on sender and responder is within
configured tolerance levelro Counter32 .1.3.6.1.4.1.9.9.744.1.2.1.1.31 |
cipslaVideoAggOWSumSDHighThe sum of one way times from source to destination
(high order 32 bits). The low order 32 bits are
stored in cipslaVideoAggOWSumSD.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.744.1.2.1.1.32 |
ciscoIpslaVideoMIBConform OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.744.2 |
ciscoIpslaVideoMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.744.2.1 |
ciscoIpslaVideoMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.744.2.2 |