CISCO-DYNAMIC-TEMPLATE-MIB
AI MIB Summary
The CISCO-DYNAMIC-TEMPLATE-MIB manages Cisco IOS-XR dynamic templates, which are configuration attribute sets dynamically applied to network interfaces to generate derived configurations. It monitors template definitions, precedence levels, and interface associations to resolve configuration conflicts where multiple templates target the same interface.
This MIB defines objects that describe dynamic templates. A dynamic template is a set of configuration attributes that a system can dynamically apply to a target.
The target of a dynamic template is the entity configured by the system using the configuration attributes contained by a template. At the time of this writing, an interface represents the only valid target of a dynamic template. However, the architecture does not prevent other target types, and hence, the MIB definition generalizes the notion of a target to allow for this.
Generally, the system does not directly apply the attributes contained by a dynamic template to an associated target. The system might generate a derived configuration from the set of dynamic templates associated with the target. A derived configuration represents the union of the configuration attributes contained by each associated dynamic template. In the case of a conflict (i.e., more than one dynamic template specifies the same configuration attribute), the system accepts the configuration attribute from the dynamic template with the highest precedence.
Main OID:
ciscoDynamicTemplateMIB.1.3.6.1.4.1.9.9.784
146
Objects
Active
Status
11
Dependencies
Imported Objects
Objects
146 total| Object Name |
|---|
ciscoDynamicTemplateMIBThis MIB defines objects that describe dynamic templates. A
dynamic template is a set of configuration attributes that a
system can dynamically apply to a target.
The target of a dynamic template is the entity configured by the
system using the configuration attributes contained by a
template. At the time of this writing, an interface represents
the only valid target of a dynamic template. However, the
architecture does not prevent other target types, and hence, the
MIB definition generalizes the notion of a target to allow for
this.
Generally, the system does not directly apply the attributes
contained by a dynamic template to an associated
target. The system might generate a derived configuration from
the set of dynamic templates associated with the target. A
derived configuration represents the union of the configuration
attributes contained by each associated dynamic template. In
the case of a conflict (i.e., more than one dynamic template
specifies the same configuration attribute), the system accepts
the configuration attribute from the dynamic template with the
highest precedence. MODULE-IDENTITY .1.3.6.1.4.1.9.9.784 |
ciscoDynamicTemplateMIBNotifs OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.784.0 |
ciscoDynamicTemplateMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.784.1 |
cdtBase OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.784.1.1 |
cdtTemplateTableThis table lists the dynamic templates maintained by the
system, including those that have been locally-configured on the
system and those pushed to the system by external policy
servers. SEQUENCE OF CdtTemplateEntry .1.3.6.1.4.1.9.9.784.1.1.1 |
cdtTemplateEntryAn entry describes a dynamic template, which serves as a
container for configuration attributes. The configuration
attributes contained by a dynamic template depends on its type.
The system automatically creates a corresponding entry when a
dynamic template has been created through another management
entity (e.g., the system's local console). Likewise, the system
automatically destroys a corresponding entry when a dynamic
template has been destroyed through another management entity.
The system automatically creates a corresponding entry when an
external policy server pushes a user profile or a service
profile to the system.
The system automatically creates a corresponding entry when it
generates a derived configuration. CdtTemplateEntry .1.3.6.1.4.1.9.9.784.1.1.1.1 |
cdtTemplateNameThis object indicates a string-value that uniquely identifies
the dynamic template.
If the corresponding instance of cdtTemplateSrc is not
'local', then the system automatically generates the name
identifying the dynamic template.ro DynamicTemplateName (CISCO-DYNAMIC-TEMPLATE-TC-MIB) .1.3.6.1.4.1.9.9.784.1.1.1.1.1 |
cdtTemplateStatusThis object specifies the status of the dynamic template. The
following columns must be valid before activating a dynamic
template:
- cdtTemplateStorage
- cdtTemplateType
However, these objects specify a default value. Thus, it is
possible to use create-and-go semantics without setting any
additional columns.
An implementation must allow the EMS/NMS to modify any column
when this column is 'active', including columns defined in
tables that have a one-to-one or sparse dependent relationship
on this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.784.1.1.1.1.2 |
cdtTemplateStorageThis object specifies what happens to the dynamic template
upon restart.
If the corresponding instance of cdtTemplateSrc is not
'local', then this column must be 'volatile'.rw StorageType (SNMPv2-TC) .1.3.6.1.4.1.9.9.784.1.1.1.1.3 |
cdtTemplateTypeThis object indicates the types of dynamic template.rw DynamicTemplateType (CISCO-DYNAMIC-TEMPLATE-TC-MIB) .1.3.6.1.4.1.9.9.784.1.1.1.1.4 |
cdtTemplateSrcThis object specifies the source of the dynamic template:
'other'
The implementation of the MIB module does not recognize the
source of the dynamic template.
'derived'
The system created the set of attributes from one or
more dynamic templates.
'local'
The dynamic template was locally configured through a
management entity, such as the local console or a SNMP
entity.
'aaaUserProfile'
The dynamic template originated from a user profile
pushed from an external policy server.
'aaaServiceProfile'
The dynamic template originated from a service profile
pushed from an external policy server.ro Enumeration .1.3.6.1.4.1.9.9.784.1.1.1.1.5 |
cdtTemplateUsageCountThis object specifies the number of targets using a dynamic templatero Unsigned32 .1.3.6.1.4.1.9.9.784.1.1.1.1.6 |
cdtTemplateTargetTableThis table contains a list of targets associated with
one or more dynamic templates. SEQUENCE OF CdtTemplateTargetEntry .1.3.6.1.4.1.9.9.784.1.1.2 |
cdtTemplateTargetEntryAn entry describes a target associated with one or more
dynamic templates.
The system automatically creates an entry when it associates a
dynamic template to a target. Likewise, the system
automatically destroys an entry when a target no longer has any
associated dynamic templates. CdtTemplateTargetEntry .1.3.6.1.4.1.9.9.784.1.1.2.1 |
cdtTemplateTargetTypeThis object indicates the type of target. DynamicTemplateTargetType (CISCO-DYNAMIC-TEMPLATE-TC-MIB) .1.3.6.1.4.1.9.9.784.1.1.2.1.1 |
cdtTemplateTargetIdThis object uniquely identifies the target within the scope of
its type. DynamicTemplateTargetId (CISCO-DYNAMIC-TEMPLATE-TC-MIB) .1.3.6.1.4.1.9.9.784.1.1.2.1.2 |
cdtTemplateTargetStatusThis object specifies the status of the dynamic template
target. The following columns must be valid before activating a
subscriber access profile:
- cdtTemplateTargetStorage
However, these objects specify a default value. Thus, it is
possible to use create-and-go semantics without setting any
additional columns.
An implementation must allow the EMS/NMS to modify any column
when this column is 'active', including columns defined in
tables that have a one-to-one or sparse dependent relationship
on this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.784.1.1.2.1.3 |
cdtTemplateTargetStorageThis object specifies what happens to the dynamic template
target upon restart.rw StorageType (SNMPv2-TC) .1.3.6.1.4.1.9.9.784.1.1.2.1.4 |
cdtTemplateAssociationTableThis table contains a list of templates associated with each
target.
This table has an expansion dependent relationship on the
cdtTemplateTargetTable, containing zero or more rows for each
target. SEQUENCE OF CdtTemplateAssociationEntry .1.3.6.1.4.1.9.9.784.1.1.3 |
cdtTemplateAssociationEntryAn entry indicates an association of a dynamic template with a
target.
The system automatically creates an entry when it associates a
dynamic template to a target.
The system also creates an entry when it derives the
configuration that it applies to a target.
The system automatically destroys an entry under the following
circumstances:
1) The target indicated by the entry no longer exists.
2) The association between the target and the dynamic template
no longer exists. CdtTemplateAssociationEntry .1.3.6.1.4.1.9.9.784.1.1.3.1 |
cdtTemplateAssociationNameThis object indicates the name of the template associated with
the target.ro DynamicTemplateName (CISCO-DYNAMIC-TEMPLATE-TC-MIB) .1.3.6.1.4.1.9.9.784.1.1.3.1.1 |
cdtTemplateAssociationPrecedenceThis object indicates the relative precedence of the
associated dynamic template. Lower values have higher
precedence than higher values.ro Unsigned32 .1.3.6.1.4.1.9.9.784.1.1.3.1.2 |
cdtTemplateUsageTableThis table contains a list of targets using each dynamic
template.
This table has an expansion dependent relationship on the
cdtTemplateTable, containing zero or more rows for each
dynamic template. SEQUENCE OF CdtTemplateUsageEntry .1.3.6.1.4.1.9.9.784.1.1.4 |
cdtTemplateUsageEntryAn entry indicates a target using the dynamic template.
The system automatically creates an entry when it associates a
dynamic template to a target.
The system also creates an entry when it derives the
configuration that it applies to a target.
The system automatically destroys an entry under the following
circumstances:
1) The target indicated by the entry no longer exists.
2) The association between the target and the dynamic template
no longer exists. CdtTemplateUsageEntry .1.3.6.1.4.1.9.9.784.1.1.4.1 |
cdtTemplateUsageTargetTypeThis object indicates the type of target using the
dynamic template.ro DynamicTemplateTargetType (CISCO-DYNAMIC-TEMPLATE-TC-MIB) .1.3.6.1.4.1.9.9.784.1.1.4.1.1 |
cdtTemplateUsageTargetIdThis object indicates the name of the target using the dynamic
templatero DynamicTemplateTargetId (CISCO-DYNAMIC-TEMPLATE-TC-MIB) .1.3.6.1.4.1.9.9.784.1.1.4.1.2 |
cdtTemplateCommonTableThis table contains attributes relating to all dynamic
templates. Observe that the type of dynamic templates
containing these attributes may change with the addition of new
dynamic template types.
This table has a sparse-dependent relationship on the
cdtTemplateTable, containing a row for each dynamic template
having a cdtTemplateType of one of the following values:
'derived'
'ppp'
'ethernet'
'ipSubscriber'
'service' SEQUENCE OF CdtTemplateCommonEntry .1.3.6.1.4.1.9.9.784.1.1.5 |
cdtTemplateCommonEntryAn entry containing attributes relating to any target.
The system automatically creates an entry when the system or the
EMS/NMS creates a row in the cdtTemplateTable with a
cdtTemplateType of on the following values:
'derived'
'ppp'
'ethernet'
'ipSubscriber'
'service'
Likewise, the system automatically destroys an entry when the
system or the EMS/NMS destroys the corresponding row in the
cdtTemplateTable. CdtTemplateCommonEntry .1.3.6.1.4.1.9.9.784.1.1.5.1 |
cdtCommonValidThis object specifies which attributes in the dynamic template
have been configured to valid values.
Each bit in this bit string corresponds to a column in this
table. If the bit is '0', then the value of the corresponding
column is not valid. If the bit is '1', then the value of the
corresponding column has been configured to a valid value.
The following list specifies the mappings between bits and the
columns:
'descr' => cdtCommonDescr
'keepaliveInt' => cdtCommonKeepaliveInt
'keepaliveRetries' => cdtCommonKeepaliveRetries
'vrf' => cdtCommonVrf
'addrPool' => cdtCommonAddrPool
'ipv4AccessGroup' => cdtCommonIpv4AccessGroup
'ipv4Unreachables' => cdtCommonIpv4Unreachables
'ipv6AccessGroup' => cdtCommonIpv6AccessGroup
'ipv6Unreachables' => cdtCommonIpv6Unreachables
'srvSubControl' => cdtCommonSrvSubControl
'srvRedirect' => cdtCommonSrvRedirect
'srvAcct' => cdtCommonSrvAcct
'srvQos' => cdtCommonSrvQos
'srvNetflow' => cdtCommonSrvNetflowrw Bits .1.3.6.1.4.1.9.9.784.1.1.5.1.1 |
cdtCommonDescrThis object specifies a human-readable description for the
dynamic template.
This column is valid only if the 'descr' bit of the
corresponding instance of cdtCommonValid is '1'.rw SnmpAdminString .1.3.6.1.4.1.9.9.784.1.1.5.1.2 |
cdtCommonKeepaliveIntThis object specifies the interval that the system sends
keepalive messages to a target.
This column is valid only if the 'keepaliveInterval' bit of the
corresponding instance of cdtCommonValid is '1'.rw Unsigned32 .1.3.6.1.4.1.9.9.784.1.1.5.1.3 |
cdtCommonKeepaliveRetriesThis object specifies the number of times the system will
resend a keepalive message without a response before it
transitions a target to an operationally down state.
This column is valid only if the 'keepaliveRetries' bit of the
corresponding instance of cdtCommonValid is '1'.rw Unsigned32 .1.3.6.1.4.1.9.9.784.1.1.5.1.4 |
cdtCommonVrfThis object specifies the name of the VRF with which a target
has an association.
This column is valid only if the 'vrf' bit of the corresponding
instance of cdtCommonValid is '1'.rw CiscoVrfName (CISCO-TC) .1.3.6.1.4.1.9.9.784.1.1.5.1.5 |
cdtCommonAddrPoolThis object specifies the name of the IP address pool the
system will use to assign an IP address to a peer of a target.
This column is valid only if the 'addrPool' bit of the
corresponding instance of cdtCommonValid is '1'.rw SnmpAdminString .1.3.6.1.4.1.9.9.784.1.1.5.1.6 |
cdtCommonIpv4AccessGroupThis object specifies the name (or number) of the IPv4 ACL
applied to a target.
This column is valid only if the 'ipv4AccessGroup' bit of the
corresponding instance of cdtCommonValid is '1'.rw SnmpAdminString .1.3.6.1.4.1.9.9.784.1.1.5.1.7 |
cdtCommonIpv4UnreachablesThis object specifies whether a target generates ICMPv4
unreachable messages.
This column is valid only if the 'ipv4Unreachables' bit of the
corresponding instance of cdtCommonValid is '1'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.784.1.1.5.1.8 |
cdtCommonIpv6AccessGroupThis object specifies the name (or number) of the IPv4 ACL
applied to a target.
This column is valid only if the 'ipv6AccessGroup' bit of the
corresponding instance of cdtCommonValid is '1'.rw SnmpAdminString .1.3.6.1.4.1.9.9.784.1.1.5.1.9 |
cdtCommonIpv6UnreachablesThis object specifies whether a target generates ICMPv6
unreachable messages.
This column is valid only if the 'ipv6Unreachables' bit of the
corresponding instance of cdtCommonValid is '1'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.784.1.1.5.1.10 |
cdtCommonSrvSubControlThis object specifies the name of the subscriber control
policy applied to a target.
The system should assume that the cbpPolicyMapType (defined by
the CISCO-CBP-BASE-CFG-MIB) of the policy is
cbpPmtControlSubscriber (defined by the CISCO-CBP-TYPE-OID-MIB).
This column is valid only if the 'srvSubControl' bit of the
corresponding instance of cdtCommonValid is '1'.rw CbpElementName (CISCO-CBP-TC-MIB) .1.3.6.1.4.1.9.9.784.1.1.5.1.11 |
cdtCommonSrvRedirectThis object specifies the name of the traffic redirect policy
applied to a target.
The system should assume that the cbpPolicyMapType (defined by
the CISCO-CBP-BASE-CFG-MIB) of the policy is
cbpPmtTrafficRedirect (defined by the CISCO-CBP-TYPE-OID-MIB).
This column is valid only if the 'srvRedirect' bit of the
corresponding instance of cdtCommonValid is '1'.rw CbpElementName (CISCO-CBP-TC-MIB) .1.3.6.1.4.1.9.9.784.1.1.5.1.12 |
cdtCommonSrvAcctThis object specifies the name of the traffic accounting policy
applied to a target.
The system should assume that the cbpPolicyMapType (defined by
the CISCO-CBP-BASE-CFG-MIB) of the policy is
cbpPmtTrafficAccounting (defined by the CISCO-CBP-TYPE-OID-MIB).
This column is valid only if the 'srvAcct' bit of the
corresponding instance of cdtCommonValid is '1'.rw CbpElementName (CISCO-CBP-TC-MIB) .1.3.6.1.4.1.9.9.784.1.1.5.1.13 |
cdtCommonSrvQosThis object specifies the name of the traffic QoS policy
applied to a target.
The system should assume that the cbpPolicyMapType (defined by
the CISCO-CBP-BASE-CFG-MIB) of the policy is cbpPmtQos (defined
by the CISCO-CBP-TYPE-OID-MIB).
This column is valid only if the 'srvQos' bit of the
corresponding instance of cdtCommonValid is '1'.rw CbpElementName (CISCO-CBP-TC-MIB) .1.3.6.1.4.1.9.9.784.1.1.5.1.14 |
cdtCommonSrvNetflowThis object specifies the name of the NetFlow policy applied to
a target.
The system should assume that the cbpPolicyMapType (defined by
the CISCO-CBP-BASE-CFG-MIB) of the policy is
cbpPmtNetflow (defined by the CISCO-CBP-TYPE-OID-MIB).
This column is valid only if the 'srvNetflow' bit of the
corresponding instance of cdtCommonValid is '1'.rw CbpElementName (CISCO-CBP-TC-MIB) .1.3.6.1.4.1.9.9.784.1.1.5.1.15 |
cdtCommonIf OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.784.1.2 |
cdtIfTemplateTableThis table contains attributes relating to interface
configuration.
This table has a sparse-dependent relationship on the
cdtTemplateTable, containing a row for each dynamic template
having a cdtTemplateType of one of the following values:
'derived'
'ppp'
'ethernet'
'ipSubscriber' SEQUENCE OF CdtIfTemplateEntry .1.3.6.1.4.1.9.9.784.1.2.1 |
cdtIfTemplateEntryAn entry containing attributes relating to interface
configuration.
The system automatically creates an entry when the system or the
EMS/NMS creates a row in the cdtTemplateTable with a
cdtTemplateType of one of the following values:
'derived'
'ppp'
'ethernet'
'ipSubscriber'
Likewise, the system automatically destroys an entry when the
system or the EMS/NMS destroys the corresponding row in the
cdtTemplateTable. CdtIfTemplateEntry .1.3.6.1.4.1.9.9.784.1.2.1.1 |
cdtIfValidThis object specifies which attributes in the dynamic template
have been configured to valid values.
Each bit in this bit string corresponds to a column in this
table. If the bit is '0', then the value of the corresponding
column is not valid. If the bit is '1', then the value of the
corresponding column has been configured to a valid value.
The following list specifies the mappings between bits and the
columns:
'mtu' => cdtIfMtu
'cdpEnable' => cdtIfCdpEnable
'flowMonitor' => cdtIfFlowMonitor
'ipv4Unnumbered' => cdtIfIpv4Unnumbered
'ipv4SubEnable' => cdtIfIpv4SubEnable
'ipv4Mtu' => cdtIfIpv4Mtu
'ipv4TcpMssAdjust' => cdtIfIpv4TcpMssAdjust
'ipv4VerifyUniRpf' => cdtIfIpv4VerifyUniRpf
'ipv4VerifyUniRpfAcl' => cdtIfIpv4VerifyUniRpfAcl
'ipv4VerifyUniRpfOpts' => cdtIfIpv4VerifyUniRpfOpts
'ipv6Enable' => cdtIfIpv6Enable
'ipv6SubEnable' => cdtIfIpv6SubEnable
'ipv6TcpMssAdjust' => cdtIfIpv6TcpMssAdjust
'ipv6VerifyUniRpf' => cdtIfIpv6VerifyUniRpf
'ipv6VerifyUniRpfAcl' => cdtIfIpv6VerifyUniRpfAcl
'ipv6VerifyUniRpfOpts' => cdtIfIpv6VerifyUniRpfOpts
'ipv6NdPrefix' => cdtIfIpv6NdPrefix,
cdtIfIpv6NdPrefixLength
'ipv6NdValidLife' => cdtIfIpv6NdValidLife
'ipv6NdPreferredLife' => cdtIfIpv6NdPreferredLife
'ipv6NdOpts' => cdtIfIpv6NdOpts
'ipv6NdDadAttempts' => cdtIfIpv6NdDadAttempts
'ipv6NdNsInterval' => cdtIfIpv6NdNsInterval
'ipv6NdReacableTime' => cdtIfIpv6NdReacableTime
'ipv6NdRaIntervalMax' => cdtIfIpv6NdRaIntervalUnits,
cdtIfIpv6NdRaIntervalMax
'ipv6NdRaIntervalMin' => cdtIfIpv6NdRaIntervalMin
'ipv6NdRaLife' => cdtIfIpv6NdRaLife
'ipv6NdRouterPreference'' => cdtIfIpv6NdRouterPreferencerw Bits .1.3.6.1.4.1.9.9.784.1.2.1.1.1 |
cdtIfMtuThis object specifies the Maximum Transfer Unit (MTU) size for
all packets sent on the target interface.
The value '0' cannot be written to an instance of this object.
However, it serves as a convenient value when the column is not
valid.
This column is valid only if the 'mtu' bit of the corresponding
instance of cdtIfValid is '1'.rw Unsigned32 (0 | 64..65535) UNITS "octets" .1.3.6.1.4.1.9.9.784.1.2.1.1.2 |
cdtIfCdpEnableThis object specifies whether the target interface participates
in the Cisco Discovery Protocol (CDP).
This column is valid only if the 'cdpEnable' bit of the
corresponding instance of cdtIfValid is '1'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.784.1.2.1.1.3 |
cdtIfFlowMonitorThis object specifies the name of the flow monitor associated
with the target interface.
This column is valid only if the 'flowMonitor' bit of the
corresponding instance of cdtIfValid is '1'.rw SnmpAdminString .1.3.6.1.4.1.9.9.784.1.2.1.1.4 |
cdtIfIpv4UnnumberedThis object specifies the interface of the source address that
the target interface uses when originating IPv4 packets.
The value '0' cannot be written to an instance of this object.
However, it serves as a convenient value when the column is
not valid (e.g., immediately following the creation of an
instance of the object).
This column is valid only if the 'ipv4Unnumbered' bit of the
corresponding instance of cdtIfValid is '1'.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.9.9.784.1.2.1.1.5 |
cdtIfIpv4SubEnableThis object specifies whether the target interface allows IPv4
subscriber sessions.
This column is valid only if the 'ipv4SubEnable' bit of the
corresponding instance of cdtIfValid is '1'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.784.1.2.1.1.6 |
cdtIfIpv4MtuThis object specifies the Maximum Transfer Unit (MTU) size for
IPv4 packets sent on the target interface.
The value '0' cannot be written to an instance of this object.
However, it serves as a convenient value when the column is not
valid.
This column is valid only if the 'ipv4Mtu' bit of the
corresponding instance of cdtIfValid is '1'.rw Unsigned32 (0 | 128..65535) UNITS "octets" .1.3.6.1.4.1.9.9.784.1.2.1.1.7 |
cdtIfIpv4TcpMssAdjustThis object specifies the adjustment to the Maximum Segment
Size (MSS) of TCP SYN packets received by the target interface
contained in IPv4 datagrams.
The value '0' cannot be written to an instance of this object.
However, it serves as a convenient value when the column is not
valid.
This column is valid only if the 'ipv4TcpMssAdjust' bit of the
corresponding instance of cdtIfValid is '1'.rw Unsigned32 (0 | 500..1460) UNITS "octets" .1.3.6.1.4.1.9.9.784.1.2.1.1.8 |
cdtIfIpv4VerifyUniRpfThis object specifies whether the type of unicast RPF the
system performs on IPv4 packets received by the target
interface.
This column is valid only if the 'ipv4VerifyUniRpf' bit of the
corresponding instance of cdtIfValid is '1'.rw UnicastRpfType (CISCO-IP-URPF-MIB) .1.3.6.1.4.1.9.9.784.1.2.1.1.9 |
cdtIfIpv4VerifyUniRpfAclThis object specifies the name (or number) of the IPv4 ACL
used to determine whether the system should permit/deny packets
received by the target interface that fail unicast RPF
verification.
This column is valid only if the 'ipv4VerifyUniRpfAcl' bit of
the corresponding instance of cdtIfValid is '1'.rw SnmpAdminString .1.3.6.1.4.1.9.9.784.1.2.1.1.10 |
cdtIfIpv4VerifyUniRpfOptsThis object specifies the options that affect how the system
performs unicast RPF on IPv4 packets received by the target
interface.
This column is valid only if the 'ipv4VerifyUniRpfOpts' bit of
the corresponding instance of cdtIfValid is '1'.rw UnicastRpfOptions (CISCO-IP-URPF-MIB) .1.3.6.1.4.1.9.9.784.1.2.1.1.11 |
cdtIfIpv6EnableThis object specifies whether the system processes IPv6
packets received by the target interface.
This column is valid only if the 'ipv6Enable' bit of the
corresponding instance of cdtIfValid is '1'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.784.1.2.1.1.12 |
cdtIfIpv6SubEnableThis object specifies whether the target interface allows IPv6
subscriber sessions.
This column is valid only if the 'ipv6SubEnable' bit of the
corresponding instance of cdtIfValid is '1'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.784.1.2.1.1.13 |
cdtIfIpv6TcpMssAdjustThis object specifies the adjustment to the Maximum Segment
Size (MSS) of TCP SYN packets received by the target interface
contained in IPv6 datagrams.
The value '0' cannot be written to an instance of this object.
However, it serves as a convenient value when the column is not
valid.
This column is valid only if the 'ipv6TcpMssAdjust' bit of the
corresponding instance of cdtIfValid is '1'.rw Unsigned32 (0 | 500..1460) UNITS "octets" .1.3.6.1.4.1.9.9.784.1.2.1.1.14 |
cdtIfIpv6VerifyUniRpfThis object specifies whether the type of unicast RPF the
system performs on IPv6 packets received by the target
interface.
This column is valid only if the 'ipv6VerifyUniRpf' bit of the
corresponding instance of cdtIfValid is '1'.rw UnicastRpfType (CISCO-IP-URPF-MIB) .1.3.6.1.4.1.9.9.784.1.2.1.1.15 |
cdtIfIpv6VerifyUniRpfAclThis object specifies the name (or number) of the IPv6 ACL
used to determine whether the system should permit/deny packets
received by the target interface that fail unicast RPF
verification.
This column is valid only if the 'ipv6VerifyUniRpfAcl' bit of
the corresponding instance of cdtIfValid is '1'.rw SnmpAdminString .1.3.6.1.4.1.9.9.784.1.2.1.1.16 |
cdtIfIpv6VerifyUniRpfOptsThis object specifies the options that affect how the system
performs unicast RPF on IPv6 packets received by the target
interface.
This column is valid only if the 'ipv6VerifyUniRpfOpts' bit of
the corresponding instance of cdtIfValid is '1'.rw UnicastRpfOptions (CISCO-IP-URPF-MIB) .1.3.6.1.4.1.9.9.784.1.2.1.1.17 |
cdtIfIpv6NdPrefixThis object specifies the IPv6 network number included in
IPv6 router advertisements sent on the target interface.
This column is valid only if the 'ipv6NdPrefix' bit of
the corresponding instance of cdtIfValid is '1'.rw InetAddressIPv6 (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.784.1.2.1.1.18 |
cdtIfIpv6NdPrefixLengthThis object specifies the length of the IPv6 prefix specified
by the corresponding instance of cdtIpv6NdPrefix.
This column is valid only if the 'ipv6NdPrefix' bit of the
corresponding instance of cdtIfValid is '1'.rw InetAddressPrefixLength (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.784.1.2.1.1.19 |
cdtIfIpv6NdValidLifeThis object specifies the interval that the system advertises
the IPv6 prefix (i.e., the corresponding instance of
cdtIfIpv6NdPrefix) as 'valid' for IPv6 router advertisements
sent on the target interface.
This column is valid only if the 'ipv6NdValidLife' bit of the
corresponding instance of cdtIfValid is '1'.rw Unsigned32 .1.3.6.1.4.1.9.9.784.1.2.1.1.20 |
cdtIfIpv6NdPreferredLifeThis object specifies the interval that the system advertises
the IPv6 prefix (i.e., the corresponding instance of
cdtIfIpv6NdPrefix) as 'preferred' for IPv6 router advertisements
sent on the target interface.
This column is valid only if the 'ipv6NdPreferredLife' bit of
the corresponding instance of cdtIfValid is '1'.rw Unsigned32 .1.3.6.1.4.1.9.9.784.1.2.1.1.21 |
cdtIfIpv6NdOptsThis object specifies options that affect advertisements sent
on the target interface:
'advertise'
This option specifies that the system should advertise
the IPv6 prefix (i.e., the corresponding instance of
cdtIfIpv6NdPrefix).
'onlink'
This option specifies that the IPv6 prefix has been
assigned to a link. If set to '0', the system
advertises the IPv6 prefix as 'offlink'.
'router'
This option indicates that the router will send the full
router address and not set the 'R' bit in prefix
advertisements.
'autoConfig'
This option indicates to hosts on the local link that
the specified prefix supports IPv6 auto-configuration.
'advertisementInterval'
This option specifies the advertisement interval option
in router advertisements sent on the target interface.
'managedConfigFlag'
This option causes the system to set the 'managed
address configuration flag' in router advertisements
sent on the target interface.
'otherConfigFlag'
This option causes the system to set the 'other stateful
configuration' flag in router advertisements sent on the
target interface.
'frameIpv6Prefix'
This option causes the system to add the prefix in a
received RADIUS framed IPv6 prefix attribute to the
target interface's neighbor discovery prefix queue and
includes it in router advertisements sent on the target
interface.
'raSupress'
This option suppresses the transmission of router
advertisements on the target interface.
This column is valid only if the 'ipv6NdOpts' bit of the
corresponding instance of cdtIfValid is '1'.rw Bits .1.3.6.1.4.1.9.9.784.1.2.1.1.22 |
cdtIfIpv6NdDadAttemptsThis object specifies the number of consecutive neighbor
solitication messages the system sends on the target interface
while performing duplicate address detection on unicast IPv6
addresses on the target interface. The value '0' disables
duplicate address detection on the target interface.
This column is valid only if the 'ipv6NdDadAttempts' bit of the
corresponding instance of cdtIfValid is '1'.rw Unsigned32 .1.3.6.1.4.1.9.9.784.1.2.1.1.23 |
cdtIfIpv6NdNsIntervalThis object specifies the interval between neighbor
solicitation retransmissions on the target interface.
This column is valid only if the 'ipv6NdNsIntervals' bit of the
corresponding instance of cdtIfValid is '1'.rw Unsigned32 .1.3.6.1.4.1.9.9.784.1.2.1.1.24 |
cdtIfIpv6NdReachableTimeThis object specifies the amount of time the system considers
a neighbor of the target interface reachable after a
reachability confirmation event has occurred. The value '0'
disables neighbor reachability detection on the target
interface.
This column is valid only if the 'ipv6NdReachable' bit of the
corresponding instance of cdtIfValid is '1'.rw Unsigned32 .1.3.6.1.4.1.9.9.784.1.2.1.1.25 |
cdtIfIpv6NdRaIntervalUnitsThis object specifies the units of time for the corresponding
instances of cdtIfIpv6NdRaIntervalMin and
cdtIfIpv6NdRaIntervalMax.
This column is valid only if the 'ipv6NdRaInterval' bit of the
corresponding instance of cdtIfValid is '1'.rw Enumeration .1.3.6.1.4.1.9.9.784.1.2.1.1.26 |
cdtIfIpv6NdRaIntervalMaxThis object specifies the maximum interval between IPv6 router
advertisements sent on the target interface.
The value '0' cannot be written to an instance of this object.
However, it serves as a convenient value when the column is not
valid.
This column is valid only if the 'ipv6NdRaInterval' bit of the
corresponding instance of cdtIfValid is '1'.rw Unsigned32 .1.3.6.1.4.1.9.9.784.1.2.1.1.27 |
cdtIfIpv6NdRaIntervalMinThis object specifies the minimum interval between IPv6 router
advertisements sent on the target interface. The value of this
column has the following restrictions:
1) This value cannot be less than 75% of the value specified
for cdtIfIpv6NdRaIntervalMax.
2) If the corresponding instance of cdtIfIpv6NdRaIntervalUnits
is 'seconds', then this value cannot be less than '3'.
3) If the corresponding instance of cdtIfIpv6NdRaIntervalUnits
is 'milliseconds', then this value cannot be less than '30'.
If the target interface template does not specify this value,
then the system automatically assumes a minimum interval that is
75% of the corresponding instance of cdtIfIpv6NdRaIntervalMax.
The value '0' cannot be written to an instance of this object.
However, it serves as a convenient value when the column is not
valid.
This column is valid only if the 'ipv6NdRaInterval' bit of the
corresponding instance of cdtIfValid is '1'.rw Unsigned32 .1.3.6.1.4.1.9.9.784.1.2.1.1.28 |
cdtIfIpv6NdRaLifeThis object specifies the router lifetime value in IPv6 router
advertisements sent on the target interface. The value '0'
specifies that neighbors should not consider the router as a
default router.rw Unsigned32 .1.3.6.1.4.1.9.9.784.1.2.1.1.29 |
cdtIfIpv6NdRouterPreferenceThis object specifies the Default Router Preference (DRP) for
the router on the target interface.
This column is valid only if the 'ipv6NdRouterPreference' bit of
the corresponding instance of cdtIfValid is '1'.rw Enumeration .1.3.6.1.4.1.9.9.784.1.2.1.1.30 |
cdtPpp OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.784.1.3 |
cdtPppTemplateTableThis table contains attributes relating to PPP connection
configuration.
This table has a sparse-dependent relationship on the
cdtTemplateTable, containing a row for each dynamic template
having a cdtTemplateType of one of the following values:
'derived'
'ppp' SEQUENCE OF CdtPppTemplateEntry .1.3.6.1.4.1.9.9.784.1.3.1 |
cdtPppTemplateEntryAn entry containing attributes relating to PPP connection
configuration.
The system automatically creates an entry when the system or the
EMS/NMS creates a row in the cdtTemplateTable with a
cdtTemplateType of one of the following values:
'derived'
'ppp'
Likewise, the system automatically destroys an entry when the
system or the EMS/NMS destroys the corresponding row in the
cdtTemplateTable. CdtPppTemplateEntry .1.3.6.1.4.1.9.9.784.1.3.1.1 |
cdtPppValidThis object specifies which attributes in the dynamic template
have been configured to valid values.
Each bit in this bit string corresponds to a column in this
table. If the bit is '0', then the value of the corresponding
column is not valid. If the bit is '1', then the value of the
corresponding column has been configured to a valid value.
The following list specifies the mappings between bits and the
columns:
accounting => cdtPppAccounting
authentication => cdtPppAuthentication
authenticationMethods => cdtPppAuthenticationMethods
authorization => cdtPppAuthorization
loopbackIgnore => cdtPppLoopbackIgnore
maxBadAuth => cdtPppMaxBadAuth
maxConfigure => cdtPppMaxConfigure
maxFailure => cdtPppMaxFailure
maxTerminate => cdtPppMaxTerminate
timeoutAuthentication => cdtPppTimeoutAuthentication
timeoutRetry => cdtPppTimeoutRetry
chapOpts => cdtPppChapOpts
chapHostname => cdtPppChapHostname
chapPassword => cdtPppChapPassword
msChapV1Opts => cdtPppMsChapV1Opts
msChapV1Hostname => cdtPppMsChapV1Hostname
msChapV1Password => cdtPppMsChapV1Password
msChapV2Opts => cdtPppMsChapV2Opts
msChapV2Hostname => cdtPppMsChapV2Hostname
msChapV2Password => cdtPppMsChapV2Password
papOpts => cdtPppPapOpts
papSentUsername => cdtPppPapUsername
papSentPassword => cdtPppPapPassword
eapOpts => cdtPppEapOpts
eapIdentity => cdtPppEapIdentity
eapPassword => cdtPppEapPassword
ipcpAddrOption => cdtPppIpcpAddrOption
ipcpDnsOption => cdtPppIpcpDnsOption
ipcpDnsPrimary => cdtPppIpcpDnsPrimary
ipcpDnsSecondary => cdtPppIpcpDnsSecondary
ipcpWinsOption => cdtPppIpcpWinsOption
ipcpWinsPrimary => cdtPppIpcpWinsPrimary
ipcpWinsSecondary => cdtPppIpcpWinsSecondary
ipcpMaskOption => cdtPppIpcpMaskOption
ipcpMask => cdtPppIpcpMask
peerDefIpAddrOpts => cdtPppPeerOpts
peerDefIpAddrSrc => cdtPppPeerDefIpAddrSrc
peerDefIpAddr => cdtPppPeerDefIpAddrrw Bits .1.3.6.1.4.1.9.9.784.1.3.1.1.1 |
cdtPppAccountingThis object specifies whether the system applies accounting
services to the target PPP connection.
This column is valid only if the 'accounting' bit of the
corresponding instance of cdtPppValid is '1'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.784.1.3.1.1.2 |
cdtPppAuthenticationThis object specifies authentication services applied to a
target PPP connection and other options affecting authentication
services:
'chap'
This option enables the Challenge Handshake Protocol (CHAP)
on a target PPP connection.
'msChap'
This option enables Microsoft's CHAP on a target PPP
connection.
'msChapV2'
This option enables version 2 of Microsoft's CHAP on a
target PPP connection.
'pap'
This option enables Password Authentication Protocol (PAP)
on a target PPP connection.
'eap'
This option enables Extensible Authentication Protocol (EAP)
on a target PPP connection.
'optional'
This option specifies that the system accepts the connection
even if the peer of a target PPP connection refuses to
accept the authentication methods the system has
requested.
'callin'
This option specifies that authentication should only happen
for incoming calls.
'oneTime'
This option specifies that the system accepts the username
and password in the username field of authentication
responses received on a target PPP connection.
This column is valid only if the 'authentication' bit of the
corresponding instance of cdtPppValid is '1'.rw Bits .1.3.6.1.4.1.9.9.784.1.3.1.1.3 |
cdtPppAuthenticationMethodsThis object specifies the name of a list of authentication
methods used on a target PPP connection. If the template does
not include this attribute, then the system uses the default
method list.
This column is valid only if the 'authentication' bit of the
corresponding instance of cdtPppValid is '1'.rw SnmpAdminString .1.3.6.1.4.1.9.9.784.1.3.1.1.4 |
cdtPppAuthorizationThis object specifies whether the system applies authorization
services to a target PPP connection.
This column is valid only if the 'authorization' bit of the
corresponding instance of cditPppValid is '1'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.784.1.3.1.1.5 |
cdtPppLoopbackIgnoreThis object specifies whether the system ignores loopback on
a target PPP connection. When the system ignores loopback,
loopback detection is disabled.
This column is valid only if the 'loopbackIgnore' bit of the
corresponding instance of cdtPppValid is '1'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.784.1.3.1.1.6 |
cdtPppMaxBadAuthThis object specifies the number of authentication failures
allowed by the system before a target PPP connection is reset.
The value '0' cannot be written to an instance of this object.
However, it serves as a convenient value when the column is not
valid.
This column is valid only if the 'maxBadAuth' bit of the
corresponding instance of cdtPppValid is '1'.rw Unsigned32 .1.3.6.1.4.1.9.9.784.1.3.1.1.7 |
cdtPppMaxConfigureThis object specifies the number of unacknowledged
Configure-Request messages a target PPP connection can send
before the system abandons LCP or NCP negotiations.
This column is valid only if the 'maxConfigure' bit of the
corresponding instance of cdtPppValid is '1'.rw Unsigned32 .1.3.6.1.4.1.9.9.784.1.3.1.1.8 |
cdtPppMaxFailureThis object specifies the number of Configure-Nak messages a
target PPP connection can receive before the system abandons LCP
or NCP negotiations.
This column is valid only if the 'maxFailure' bit of the
corresponding instance of cdtPppValid is '1'.rw Unsigned32 .1.3.6.1.4.1.9.9.784.1.3.1.1.9 |
cdtPppMaxTerminateThis object specifies the number of unacknowledged
Terminate-Request messages a target PPP connection can send
before the system abandons LCP or NCP negotiations.
This column is valid only if the 'maxTerminate' bit of the
corresponding instance of cdtPppValid is '1'.rw Unsigned32 .1.3.6.1.4.1.9.9.784.1.3.1.1.10 |
cdtPppTimeoutAuthenticationThis objects specifies the maximum time the system will wait
for a response to an authentication request on a target PPP
connection.
This column is valid only if the 'timeoutAuthentication' bit of
the corresponding instance of cdtPppValid is '1'.rw Unsigned32 .1.3.6.1.4.1.9.9.784.1.3.1.1.11 |
cdtPppTimeoutRetryThis objects specifies the maximum time the system will wait
for a response to a PPP control packets on a target PPP
connection.
This column is valid only if the 'timeoutRetry' bit of the
corresponding instance of cdtPppValid is '1'.rw Unsigned32 .1.3.6.1.4.1.9.9.784.1.3.1.1.12 |
cdtPppChapOptsThis object specifies how the system processes the CHAP on a
target PPP connection:
'refuse'
This option specifies that the system should refuse CHAP
requests from peers of a target PPP connection.
'callin'
This option specifies that the system should only refuse
CHAP requests for incoming calls on a target PPP
connection. This option is only relevant if the
'refuse' option is set to '1'.
'wait'
This option delays CHAP authentication until after the
peer of a target PPP connection has authenticated itself
to the system.
'encrypted'
This option specifies that the value specified by the
corresponding instance of cdtPppChapPassword is already
encrypted.
This column is valid only if the 'chapOpts' bit of the
corresponding instance of cdtPppValid is '1'.rw Bits .1.3.6.1.4.1.9.9.784.1.3.1.1.13 |
cdtPppChapHostnameThis object specifies the hostname sent in a CHAP response
on a target PPP connection. If the template does not include
this attribute, then the system uses its assigned hostname.
This column is valid only if the 'chapHostname' bit of the
corresponding instance of cdtPppValid is '1'.rw SnmpAdminString .1.3.6.1.4.1.9.9.784.1.3.1.1.14 |
cdtPppChapPasswordThis object specifies the password used to construct a CHAP
response on the target PPP connection.
This column is valid only if the 'chapPassword' bit of the
corresponding instance of cdtPppValid is '1'.rw SnmpAdminString .1.3.6.1.4.1.9.9.784.1.3.1.1.15 |
cdtPppMsChapV1OptsThis object specifies how the system processes version 1 of
Microsoft CHAP on a target PPP connection:
'refuse'
This option specifies that the system should refuse
Microsoft CHAP (v1) requests from peers of a target PPP
connection.
'callin'
This option specifies that the system should only refuse
Microsoft CHAP (v1) requests for incoming calls on a
target PPP connection. This option is only relevant if
the 'refuse' option is set to '1'.
'wait'
This option delays Microsoft CHAP (v1) authentication
until after the peer of a target PPP connection has
authenticated itself to the system.
'encrypted'
This option specifies that the value specified by the
corresponding instance of cdtPppMsChapV1Password is
already encrypted.
This column is valid only if the 'msChapV1Opts' bit of the
corresponding instance of cdtPppValid is '1'.rw Bits .1.3.6.1.4.1.9.9.784.1.3.1.1.16 |
cdtPppMsChapV1HostnameThis object specifies the hostname sent in a Microsoft CHAP
(v1) response on a target PPP connection. If the template does
not include this attribute, then the system uses its assigned
hostname.
This column is valid only if the 'msChapV1Hostname' bit of the
corresponding instance of cdtPppValid is '1'.rw SnmpAdminString .1.3.6.1.4.1.9.9.784.1.3.1.1.17 |
cdtPppMsChapV1PasswordThis object specifies the password used to construct a
Microsoft CHAP (v1) response on a target PPP connection.
This column is valid only if the 'msChapV1Password' bit of the
corresponding instance of cdtPppValid is '1'.rw SnmpAdminString .1.3.6.1.4.1.9.9.784.1.3.1.1.18 |
cdtPppMsChapV2OptsThis object specifies how the system processes version 2 of
Microsoft CHAP on a target PPP connection:
'refuse'
This option specifies that the system should refuse
Microsoft CHAP (v2) requests from peers of a target PPP
connection.
'callin'
This option specifies that the system should only refuse
Microsoft CHAP (v2) requests for incoming calls on a
target PPP connection. This option is only relevant if
the 'refuse' option is set to '1'.
'wait'
This option delays Microsoft CHAP (v2) authentication
until after the peer of a target PPP connection has
authenticated itself to the system.
'encrypted'
This option specifies that the value specified by the
corresponding instance of cdtPppMsChapV2Password is
already encrypted.
This column is valid only if the 'msChapV2Opts' bit of the
corresponding instance of cdtPppValid is '1'.rw Bits .1.3.6.1.4.1.9.9.784.1.3.1.1.19 |
cdtPppMsChapV2HostnameThis object specifies the hostname sent in a Microsoft CHAP
(v2) response on a target PPP connection. If the template does
not include this attribute, then the system uses its assigned
hostname.
This column is valid only if the 'msChapV2Hostname' bit of the
corresponding instance of cdtPppValid is '1'.rw SnmpAdminString .1.3.6.1.4.1.9.9.784.1.3.1.1.20 |
cdtPppMsChapV2PasswordThis object specifies the password used to construct a
Microsoft CHAP (v2) response on a target PPP connection.
This column is valid only if the 'msChapV2Password' bit of the
corresponding instance of cdtPppValid is '1'.rw SnmpAdminString .1.3.6.1.4.1.9.9.784.1.3.1.1.21 |
cdtPppPapOptsThis object specifies how the system processes the PAP on a
target PPP connection:
'refuse'
This option specifies that the system should refuse PAP
requests from peers of a target PPP connection.
'encrypted'
This option specifies that the value specified by the
corresponding instance of cdtPppPapSentPassword is
already encrypted.
This column is valid only if the 'papOpts' bit of the
corresponding instance of cdtPppValid is '1'.rw Bits .1.3.6.1.4.1.9.9.784.1.3.1.1.22 |
cdtPppPapUsernameThis object specifies the username sent in a PAP response on
a target PPP connection.
This column is valid only if the 'papUsername' bit of the
corresponding instance of cdtPppValid is '1'.rw SnmpAdminString .1.3.6.1.4.1.9.9.784.1.3.1.1.23 |
cdtPppPapPasswordThis object specifies the username used to construct a PAP
response on a target PPP connection.
This column is valid only if the 'papPassword' bit of the
corresponding instance of cdtPppValid is '1'.rw SnmpAdminString .1.3.6.1.4.1.9.9.784.1.3.1.1.24 |
cdtPppEapOptsThis object specifies how the system processes the EAP on a
target PPP connection:
'refuse'
This option specifies that the system should refuse EAP
requests from peers of a target PPP connection.
'callin'
This option specifies that the system should only refuse EAP
requests for incoming calls on a target PPP connection.
This option is only relevant if the 'refuse' option is
set to '1'.
'wait'
This option delays EAP authentication until after the
peer of a target PPP connection has authenticated itself
to the system.
'local'
This option specifies that the system should locally
authenticate the peer of a target PPP connection,
rather than acting as a proxy to an external AAA server.
This column is valid only if the 'eapOpts' bit of the
corresponding instance of cdtPppValid is '1'.rw Bits .1.3.6.1.4.1.9.9.784.1.3.1.1.25 |
cdtPppEapIdentityThis object specifies the identity sent in an EAP response on
a target PPP connection.
This column is valid only if the 'eapIdentity' bit of the
corresponding instance of cdtPppValid is '1'.rw SnmpAdminString .1.3.6.1.4.1.9.9.784.1.3.1.1.26 |
cdtPppEapPasswordThis object specifies the password used to construct an EAP
response on a target PPP connection.
This column is valid only if the 'eapPassword' bit of the
corresponding instance of cdtPppValid is '1'.rw SnmpAdminString .1.3.6.1.4.1.9.9.784.1.3.1.1.27 |
cdtPppIpcpAddrOptionThis object specifies the IPCP address option for a target PPP
connection:
'other'
The implementation of this MIB module does not recognize
the configured IPCP address option.
'accept'
The system accepts any non-zero IP address from the peer
of a target PPP connection.
'required'
The system disconnects the peer of a target PPP
connection if it could not negotiate an IP address.
'unique'
The system disconnects the peer of a target PPP
connection if the IP address is already in use.
This column is valid only if the 'ipcpAddrOption' bit of the
corresponding instance of cdtPppValid is '1'.rw Enumeration .1.3.6.1.4.1.9.9.784.1.3.1.1.28 |
cdtPppIpcpDnsOptionThis object specifies the IPCP DNS option for the dynamic
interface:
'other'
The implementation of this MIB module does not recognize
the configured DNS option.
'accept'
The system accepts any non-zero DNS address form the
peer of a target PPP connection.
'request'
The system requests the DNS address from the peer of a
target PPP connection.
'reject'
The system rejects the DNS option from the peer of a
target PPP connection.
This column is valid only if the 'ipcpDnsOption' bit of the
corresponding instance of cdtPppValid is '1'.rw Enumeration .1.3.6.1.4.1.9.9.784.1.3.1.1.29 |
cdtPppIpcpDnsPrimaryThis object specifies the IP address of the primary DNS server
offered to the peer of a target PPP connection.
This column is valid only if the 'ipcpDnsPrimary' bit of the
corresponding instance of cdtPppValid is '1'.rw InetAddressIPv4 (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.784.1.3.1.1.30 |
cdtPppIpcpDnsSecondaryThis object specifies the IP address of the secondary DNS
server offered to the peer of a target PPP connection.
This column is valid only if the 'ipcpDnsSecondary' bit of the
corresponding instance of cdtPppValid is '1'.rw InetAddressIPv4 (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.784.1.3.1.1.31 |
cdtPppIpcpWinsOptionThis object specifies the IPCP WINS option for a target PPP
connection:
'other'
The implementation of this MIB module does not recognize
the configured WINS option.
'accept'
The system accepts any non-zero WINS address from the
peer of a target PPP connection.
'request'
The system requests the WINS address from the peer of
a target PPP connection.
'reject'
The system rejects the WINS option from the peer of a
target PPP connection.
This column is valid only if the 'ipcpWinsOption' bit of the
corresponding instance of cdtPppValid is '1'.rw Enumeration .1.3.6.1.4.1.9.9.784.1.3.1.1.32 |
cdtPppIpcpWinsPrimaryThis object specifies the IP address of the primary WINS server
offered to the peer of a target PPP connection.
This column is valid only if the 'ipcpWinsPrimary' bit of the
corresponding instance of cdtPppValid is '1'.rw InetAddressIPv4 (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.784.1.3.1.1.33 |
cdtPppIpcpWinsSecondaryThis object specifies the IP address of the secondary WINS
server offered to the peer of a target PPP connection.
This column is valid only if the 'ipcpWinsSecondary' bit of the
corresponding instance of cdtPppValid is '1'.rw InetAddressIPv4 (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.784.1.3.1.1.34 |
cdtPppIpcpMaskOptionThis object specifies the IPCP IP subnet mask option for a
target PPP connection:
'other'
The implementation of this MIB module does not recognize
the configured IP subnet mask option.
'request'
The system requests the IP subnet mask from the peer of
a target PPP connection.
'reject'
The system rejects the IP subnet mask option from the
peer of a target PPP connection.
This column is valid only if the 'ipcpMaskOption' bit of the
corresponding instance of cdtPppValid is '1'.rw Enumeration .1.3.6.1.4.1.9.9.784.1.3.1.1.35 |
cdtPppIpcpMaskThis object specifies the IP address mask offered to the peer
of a target PPP connection.
This column is valid only if the 'ipcpMask' bit of the
corresponding instance of cdtPppValid is '1'.rw InetAddressIPv4 (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.784.1.3.1.1.36 |
cdtPppPeerDefIpAddrOptsThis object specifies options that affect how the system
assigns an IP address to the peer of a target PPP connection:
'ipAddrForced'
This option forces the system to assign the next
available IP address in the pool to the peer of a
target PPP connection. When disabled, the peer may
negotiate a specific IP address or the system can assign
the peer its previously assigned IP address.
'matchAaaPools'
This option specifies that the names of the IP address
pools provided by an external AAA server must appear in
the corresponding list of IP address pool specified by
the cdtPppPeerIpAddrPoolTable.
'backupPools'
This option specifies that the corresponding names of
the IP address pools specified by the
cditPppPeerIpAddrPoolTable serve as backup pools to
those provided by an external AAA server.
'staticPools'
This option suppresses an attempt to load pools from an
external AAA server when the system encounters a missing
pool name.
This column is valid only if the 'peerIpAddrOpts' bit of the
corresponding instance of cdtPppValid is '1'.rw Bits .1.3.6.1.4.1.9.9.784.1.3.1.1.37 |
cdtPppPeerDefIpAddrSrcThis object specifies how the system assigns an IP address to
the peer of a target PPP connection:
'static'
The system assigns the IP address specified by the
corresponding instance of cdtPppPeerDefIpAddr.
'pool'
The system allocates the first available IP address from
the corresponding list of named pools contained by the
cdtPppPeerIpAddrPoolTable.
'dhcp'
The system acts as a DHCP proxy-client to obtain an IP
address.
This column is valid only if the 'peerDefIpAddrSrc' bit of the
corresponding instance of cdtPppValid is '1'.rw Enumeration .1.3.6.1.4.1.9.9.784.1.3.1.1.38 |
cdtPppPeerDefIpAddrThis object specifies the IP address the system assigns to the
peer of a target PPP connection.
This column is valid only if the 'peerDefIpAddr' bit of the
corresponding instance of cdtPppValid is '1'.rw InetAddressIPv4 (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.784.1.3.1.1.39 |
cdtPppPeerIpAddrPoolTableThis table contains a prioritized list of named pools for each
PPP template. A list corresponding to a PPP template
specifies the pools the system searches in an attempt to
assign an IP address to the peer of a target PPP connection.
The system searches the pools in the order of their priority.
This table has an expansion dependent relationship on the
cdtPppTemplateTable, containing zero or more rows for each PPP
template. SEQUENCE OF CdtPppPeerIpAddrPoolEntry .1.3.6.1.4.1.9.9.784.1.3.2 |
cdtPppPeerIpAddrPoolEntryAn entry specifies a named pool in a list of pools associated
with a PPP template. A PPP template can only have named
pools associated with it if it has a cdtPppPeerIpAddrSrc of
'pool'.
Any attempt to create an entry for a PPP template that does not
have a cdtPppPeerIpAddrSrc of 'pool' must result in a response
having an error-status of 'inconsistentValue'.
The system automatically creates a corresponding entry when the
system associates a named pool with a PPP template through
another management entity (e.g., the system's local console).
The system automatically destroys an entry under the following
circumstances:
1) The system or EMS/NMS destroys the corresponding row in the
cdtTemplateTable.
2) The system or EMS/NMS sets the corresponding instance of
cdtPppPeerIpAddrSrc with a value other than 'pool'. CdtPppPeerIpAddrPoolEntry .1.3.6.1.4.1.9.9.784.1.3.2.1 |
cdtPppPeerIpAddrPoolPriorityThis object indicates the relative priority of the named pool
in the list corresponding to a PPP template. The system
searches pools in the order of priority, where lower values
represent higher priority. Unsigned32 .1.3.6.1.4.1.9.9.784.1.3.2.1.1 |
cdtPppPeerIpAddrPoolStatusThis object specifies the status of the entry. The following
columns must be valid before activating a subscriber access
profile:
- cdtPppPeerIpAddrPoolStorage
- cdtPppPeerIpAddrPoolName
However, these objects specify a default value. Thus, it is
possible to use create-and-go semantics without setting any
additional columns.
An implementation must not allow the EMS/NMS to create an entry
if the corresponding instance of cdtPppPeerIpAddrSrc is not
'pool'.
An implementation must allow the EMS/NMS to modify any column
when this column is 'active'.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.784.1.3.2.1.2 |
cdtPppPeerIpAddrPoolStorageThis object specifies what happens to the name pool entry upon
restart.
If the corresponding instance of cdtTemplateSrc is not 'local',
then this column must be 'volatile'.rw StorageType (SNMPv2-TC) .1.3.6.1.4.1.9.9.784.1.3.2.1.3 |
cdtPppPeerIpAddrPoolNameThis object specifies the name of the IP address pool
associated with the PPP template.rw SnmpAdminString .1.3.6.1.4.1.9.9.784.1.3.2.1.4 |
cdtEthernet OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.784.1.4 |
cdtEthernetTemplateTableThis table contains attributes relating to dynamic interfaces
initiated on Ethernet virtual interfaces (e.g., EoMPLS) or
automatically created VLANs.
This table has a sparse-dependent relationship on the
cdtTemplateTable, containing a row for each dynamic template
having a cdtTemplateType of one of the following values:
'derived'
'ethernet' SEQUENCE OF CdtEthernetTemplateEntry .1.3.6.1.4.1.9.9.784.1.4.1 |
cdtEthernetTemplateEntryAn entry containing attributes relating to dynamic interfaces
initiated on Ethernet virtual interfaces (e.g., EoMPLS) or
automatically created VLANs.
The system automatically creates an entry when the system or the
EMS/NMS creates a row in the cdtTemplateTable with a
cdtTemplateType of one of the following values:
'derived'
'ethernet'
Likewise, the system automatically destroys an entry when the
system or the EMS/NMS destroys the corresponding row in the
cdtTemplateTable. CdtEthernetTemplateEntry .1.3.6.1.4.1.9.9.784.1.4.1.1 |
cdtEthernetValidThis object specifies which attributes in the dynamic template
have been configured to valid values.
Each bit in this bit string corresponds to a column in this
table. If the bit is '0', then the value of the corresponding
column is not valid. If the bit is '1', then the value of the
corresponding column has been configured to a valid value.
The following list specifies the mappings between bits and the
columns:
bridgeDomain => cdtEthernetBridgeDomain
pppoeEnable => cdtEthernetPppoeEnable
ipv4PointToPoint => cdtEthernetIpv4PointToPoint
macAddr => cdtEthernetMacAddrrw Bits .1.3.6.1.4.1.9.9.784.1.4.1.1.1 |
cdtEthernetBridgeDomainThis object specifies the name of the bridge domain...rw SnmpAdminString .1.3.6.1.4.1.9.9.784.1.4.1.1.2 |
cdtEthernetPppoeEnableThis object specifies whether...rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.784.1.4.1.1.3 |
cdtEthernetIpv4PointToPointThis object specifies whether...rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.784.1.4.1.1.4 |
cdtEthernetMacAddrThis object specifies the...rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.9.9.784.1.4.1.1.5 |
cdtIpSubscriber OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.784.1.5 |
cdtService OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.784.1.6 |
cdtSrvTemplateTableThis table contains attributes relating to a service.
This table has a sparse-dependent relationship on the
cdtTemplateTable, containing a row for each dynamic template
having a cdtTemplateType of one of the following values:
'derived'
'service' SEQUENCE OF CdtSrvTemplateEntry .1.3.6.1.4.1.9.9.784.1.6.1 |
cdtSrvTemplateEntryAn entry containing attributes relating to a service.
The system automatically creates entry when the system or the
EMS/NMS creates a row in the cdtTemplateTable with a
cdtTemplateType of one of the following values:
'derived'
'service'
Likewise, the system automatically destroys an entry when the
system or the EMS/NMS destroys the corresponding row in the
cdtTemplateTable. CdtSrvTemplateEntry .1.3.6.1.4.1.9.9.784.1.6.1.1 |
cdtSrvValidThis object specifies which attributes in the dynamic template
have been configured to valid values.
Each bit in this bit string corresponds to a column in this
table. If the bit is '0', then the value of the corresponding
column is not valid. If the bit is '1', then the value of the
corresponding column has been configured to a valid value.
The following list specifies the mappings between bits and the
columns:
networkSrv => cdtSrvNetworkSrv
vpdnGroup => cdtSrvVpdnGroup
sgSrvGroup => cdtSrvGroup
sgSrvType => cdtSrvSgSrvType
multicast => cdtSrvMulticastrw Bits .1.3.6.1.4.1.9.9.784.1.6.1.1.1 |
cdtSrvNetworkSrvThis object specifies the type of network service provided by
the target service:
'other'
The implementation of this MIB module does not recognize
the configured network service.
'none'
The target subscriber service does not provide a network
service to subscribers sessions.
'local'
The target subscriber service provides local termination
for subscriber sessions.
'vpdn'
The target subscriber service provides a Virtual Private
Dialup Network service for subscriber sessions.
This column is valid only if the 'networkSrv' bit of the
corresponding instance of cdtSrvValid is '1'.rw Enumeration .1.3.6.1.4.1.9.9.784.1.6.1.1.2 |
cdtSrvVpdnGroupThis object specifies the name of the VPDN group used to
configure the network service.
This column is valid only if the 'vpdnGroup' bit of the
corresponding instance of cdtSrvValid is '1'.rw SnmpAdminString .1.3.6.1.4.1.9.9.784.1.6.1.1.3 |
cdtSrvSgSrvGroupThis object specifies the name of the service group with which
the system associates subscriber sessions. A service group
specifies a set of services that may be active simultaneously
for a given subscriber session. Typically, a service group
contains a primary service and one or more secondary services.
This column is valid only if the 'sgSrvGroup' bit of the
corresponding instance of cdtSrvValid is '1'.rw SnmpAdminString .1.3.6.1.4.1.9.9.784.1.6.1.1.4 |
cdtSrvSgSrvTypeThis object specifies whether the target service specifies a
network-forwarding policy:
'primary'
The target service specifies a network-forwarding
policy. Primary services are mutually exclusive; that
is, only one primary service can be activated for any
given subscriber session.
'secondary'
The target service has a dependence on the primary
service in the group specified by the corresponding
instance of cdtSuBSrvSgSrvGroup. After the system
activates the primary service, it activates secondary
services. When the system deactivates the primary
service, then it deactivates all the secondary services
in the service group.
This column is valid only if the 'sgSrvType' bit of the
corresponding instance of cdtSrvValid is '1'.rw Enumeration .1.3.6.1.4.1.9.9.784.1.6.1.1.5 |
cdtSrvMulticastThis objects specifies whether the system enables multicast
service for subscriber sessions of the target service.
This column is valid only if the 'sgSrvMcastRoutingIf' bit of
the corresponding instance of cdtSrvValid is '1'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.784.1.6.1.1.6 |
cdtSubscriberGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.784.1.7 |
ciscoDynamicTemplateMIBConform OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.784.2 |
ciscoDynamicTemplateMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.784.2.1 |
ciscoDynamicTemplateMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.784.2.2 |