CADANT-CMTS-LAYER2CMTS-MIB
AI MIB Summary
The CADANT-CMTS-LAYER2CMTS-MIB monitors Layer 2 bridging configurations on Cadant CMTS hardware, specifically tracking bridge group assignments, per-group spanning tree states, and the policy-based mapping of ISP subnet addresses to bridge interfaces.
This MIB module contains the following information: 1) The concept of bridge groups and bridge ports 2) The policy governed the assigment of Internet Service Provider's subnet addresses per bridge group 3) Support for per bridge group spanning tree
Main OID:
cadLayer2Mib.1.3.6.1.4.1.4998.1.1.20.1
168
Objects
Active
Status
9
Dependencies
Imported Objects
Objects
168 total| Object Name |
|---|
cadLayer2MibThis MIB module contains the following information:
1) The concept of bridge groups and bridge ports
2) The policy governed the assigment of
Internet Service Provider's subnet addresses
per bridge group
3) Support for per bridge group spanning tree MODULE-IDENTITY .1.3.6.1.4.1.4998.1.1.20.1 |
IMPORTSThis MIB module contains the following information:
1) The concept of bridge groups and bridge ports
2) The policy governed the assigment of
Internet Service Provider's subnet addresses
per bridge group
3) Support for per bridge group spanning tree of cadMacChlCardSubType to CerCardSubType." REVISION "201108170000Z" -- Aug 17, 2011 .1.3.6.1.4.1.4998.1.1.20.1 |
cadBridgeGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4998.1.1.20.1.1 |
cadBridgeGroupGeneral OBJECT IDENTIFIER .1.3.6.1.4.1.4998.1.1.20.1.1.1 |
cadBridgeGroupMaxNumThe maximum number of bridge groups supported.ro Integer32 .1.3.6.1.4.1.4998.1.1.20.1.1.1.1 |
cadBridgeGroupTableA table (and along with other supported tables)
contains bridge group information.
A bridge group is actually a Port-Vlan concept
which consists of one or more E-ports and one
or more D-ports.
Each D-port includes its associated U-ports and is
further subdivided into 3 sub-ports associated with
different types of traffic. The CM sub-port carries
traffic for the cable-modem itself. The CPEAUTH sub-port
carries traffic for an authorized CPE behind a cable-modem.
The CPEUNAUTH sub-port carries traffic for an unauthorized
CPE behind a cable-modem.
Initially, all ports belong to the OAM&P bridge group when
a card is first provisioned. Bridge ports can only exist
in one bridge group at a time and can be moved between them.
Generally, the CPEAUTH sub-port on the D card would be in a
bridge group with an E port that had access to the internet
and the DHCP servers for the ISP used by the subscriber.
The CM sub-port would be in a bridge group with an E port that
had access to the DHCP servers and administrative controls
for the MSO. The CPEUNAUTH sub-port would be in a bridge
group that included access to a sign-on server. SEQUENCE OF CadBridgeGroupEntry .1.3.6.1.4.1.4998.1.1.20.1.1.2 |
cadBridgeGroupEntryA conceptual row containing information about different types of CMTS's
broadcast domains and their configuration parameters. CadBridgeGroupEntry .1.3.6.1.4.1.4998.1.1.20.1.1.2.1 |
cadBgIndexCMTS broadcast domain Id. Used as index.
It has a value from 1 to the value of bridgeGroupMaxNum CadBridgeGroupId (CADANT-TC) .1.3.6.1.4.1.4998.1.1.20.1.1.2.1.1 |
cadBgNameSymbolic Name of the domain.rw DisplayString .1.3.6.1.4.1.4998.1.1.20.1.1.2.1.2 |
cadBgRowStatusControl Object for row creation and deletion.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.1.2.1.11 |
cadBridgeGroupStatsTableA table which contains read-only (status) information on bridge groups. SEQUENCE OF CadBridgeGroupStatsEntry .1.3.6.1.4.1.4998.1.1.20.1.1.10 |
cadBridgeGroupStatsEntryA conceptual row containing read-only information on bridge groups. CadBridgeGroupStatsEntry .1.3.6.1.4.1.4998.1.1.20.1.1.10.1 |
cadBgLeaderBgpIdThe bridge port that is the leader for this bridge
group. If there are no bridge ports in this bridge
group or there are multiple bridge ports in this
bridge group but none of them make a clear leader,
then cadBgLeaderBgpId is zero. Otherwise,
it is the cadBgpId of the leader bridge port for this
bridge group.ro InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.4998.1.1.20.1.1.10.1.1 |
cadBgMacAddressThe mac address of the layer 2 entity associated with this
bridge group. If there are no layer 2 entities associated
with the bridge group, this value will be zero. In the
case of a bundle, this will be the mac address of the
bundle group leader.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.1.10.1.2 |
cadBridgePortTableA table contain broadcast domain Ports Configuration
(i.e. E ports, D-ports, M-Ports...etc) SEQUENCE OF CadBridgePortEntry .1.3.6.1.4.1.4998.1.1.20.1.1.11 |
cadBridgePortEntryA conceptual row containing port configuration within a
bridge group. CadBridgePortEntry .1.3.6.1.4.1.4998.1.1.20.1.1.11.1 |
cadBgpGroupIdBridge group index.
The same index used in bridgeGroupTable to
identify a bridge group.rw CadBridgeGroupId (CADANT-TC) .1.3.6.1.4.1.4998.1.1.20.1.1.11.1.1 |
cadBgpIdThe secondary index of this table identifies
a port in a given bridge group. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4998.1.1.20.1.1.11.1.2 |
cadBgpCardIdThe slot number of the card containing this bridge port.ro CardId (CADANT-TC) .1.3.6.1.4.1.4998.1.1.20.1.1.11.1.3 |
cadBgpCardTypeThe primary Card Type.
Refer to Cadant's Equipment Mib for CerCardType definition.ro CerCardType (CADANT-TC) .1.3.6.1.4.1.4998.1.1.20.1.1.11.1.4 |
cadBgpPortIdThe port number of the physical port containing this bridge port.ro PortId (CADANT-TC) .1.3.6.1.4.1.4998.1.1.20.1.1.11.1.5 |
cadBgpTypeThe type of this bridge port. CadBridgePortType (CADANT-TC) .1.3.6.1.4.1.4998.1.1.20.1.1.11.1.6 |
cadBgpBundleGroupIdThe bridge port which is the bundle leader.
If this value is 0, then this port is not
part of a bundle group. If this value is equal
to its cadBgpId, then this port is the
bundle leader for its group. Otherwise, this
value must point to a valid bridge port.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.4998.1.1.20.1.1.11.1.10 |
cadBgpMacAddressThe current mac address associated with
the bridge port. Initially, this is the address
associated with the MAC or Ethernet port, but can
change as a result of bundling or sparing operations.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.1.11.1.11 |
cadBridgeGroupPortStatusTableA table which contains status information
on bridge group members. SEQUENCE OF CadBridgeGroupPortStatusEntry .1.3.6.1.4.1.4998.1.1.20.1.1.12 |
cadBridgeGroupPortStatusEntryA conceptual row containing status information
on possible bridge group members. CadBridgeGroupPortStatusEntry .1.3.6.1.4.1.4998.1.1.20.1.1.12.1 |
cadBgpStatGroupIdThe bridge group id to which this physical interface belongs. CadBridgeGroupId (CADANT-TC) .1.3.6.1.4.1.4998.1.1.20.1.1.12.1.1 |
cadBgpStatMacIfIndexThe ifIndex of the layer 2 entity associated with the bridge group. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4998.1.1.20.1.1.12.1.2 |
cadBgpStatPhyIfIndexThe ifIndex of the physical entity associated with the
bridge group. This ifIndex corresponds to an actual physical
port on the C4. For NAM ports that are both a layer 2 and
physical entity, this value may be the same as as the
cadBgmemStatMacIfIndex. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4998.1.1.20.1.1.12.1.3 |
cadBgpStatPhyCardIdThe cardId of the slot associated with the physical ifindex.ro CardId (CADANT-TC) .1.3.6.1.4.1.4998.1.1.20.1.1.12.1.4 |
cadBgpStatPhyPortIdThe portId of the port associated with the physical ifindex.ro PortId (CADANT-TC) .1.3.6.1.4.1.4998.1.1.20.1.1.12.1.5 |
cadDot3adAggTableThis table extends the dot3adAggTable to control LACP. SEQUENCE OF CadDot3adAggEntry .1.3.6.1.4.1.4998.1.1.20.1.1.13 |
cadDot3adAggEntryThis is an extension of the dot3adAggEntry
table that adds a LAG-level LACP enable. CadDot3adAggEntry .1.3.6.1.4.1.4998.1.1.20.1.1.13.1 |
cadDot3adAggIdThe unique identifier allocated to this Aggregator by the CMTS system. INTEGER .1.3.6.1.4.1.4998.1.1.20.1.1.13.1.1 |
cadDot3adAggIndexThe unique ifInex to identify this Aggregator.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4998.1.1.20.1.1.13.1.2 |
cadDot3adAggMacAddressThe MAC address of this Aggregator.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.1.13.1.3 |
cadDot3adAggLacpEnableTRUE if LACP is enabled for this LAG, FALSE if it is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.1.13.1.4 |
cadDot3adAggLacpModeThe default administrative status of the LACP protocol for ports
In this LAG. Controls bit 0 of dot3adAggPortPartnerOperState
to zero for passive and is set to one for active.rw Enumeration .1.3.6.1.4.1.4998.1.1.20.1.1.13.1.5 |
cadDot3adAggLacpRateSpecifies the default requested exchange rate of LACP packets for ports
In this LAG. Controls bit 1 (LACP_Timeout) in dot3adAggPortActorOperState
slow(1): The device requests its peers to send LACP packets
at a slow rate to this interface. LACP_Timeout equals 0
(transmission interval of 30 seconds, long timeout of 90 seconds)
fast(2) : The device requests its peers to send LACP packets
at fast rate to this interface. LACP_Timeout equals 1
(transmission interval of 1 second, short timeout of 3 seconds).rw Enumeration .1.3.6.1.4.1.4998.1.1.20.1.1.13.1.6 |
cadDot3adAggMinLinksSets the minimum number of ports that must be able to pass
dataplane traffic for this LAG to be in-service. If the number of
such ports in this LAG falls below this value, the entire LAG
goes OOS.rw INTEGER .1.3.6.1.4.1.4998.1.1.20.1.1.13.1.7 |
cadDot3adAggDescriptionThe description of the Link Aggregation Group.rw DisplayString .1.3.6.1.4.1.4998.1.1.20.1.1.13.1.8 |
cadDot3adAggTrapInhIf a bit is set, the corresponding state change trap will not be sent.
By default only linkUp and linkDown notifications are enabled.rw Bits .1.3.6.1.4.1.4998.1.1.20.1.1.13.1.9 |
cadDot3adAggAdminStateThe administrative state of the Link Aggregation Group.rw AdminState (CADANT-TC) .1.3.6.1.4.1.4998.1.1.20.1.1.13.1.10 |
cadDot3adAggPrStateThe primary state of the Link Aggregation Group.ro PrimaryState (CADANT-TC) .1.3.6.1.4.1.4998.1.1.20.1.1.13.1.11 |
cadDot3adAggSecStateThe secondary state of the Link Aggregation Group.ro SecondaryState (CADANT-TC) .1.3.6.1.4.1.4998.1.1.20.1.1.13.1.12 |
cadDot3adAggRowStatusControl Object for row creation and deletion.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.1.13.1.13 |
cadDot3adAggSystemIDEquivalent to the dot3adAggActorSystemID in the dot3adAggTable.
A 6-octet read-write MAC address value used as a unique
identifier for the System that contains this Aggregator.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.1.13.1.14 |
cadDot3adParams OBJECT IDENTIFIER .1.3.6.1.4.1.4998.1.1.20.1.1.14 |
cadDot3adSystemPriorityA 2-octet value that indicates the priority
value associated with the Actor's System ID.rw INTEGER .1.3.6.1.4.1.4998.1.1.20.1.1.14.1 |
cadAging OBJECT IDENTIFIER .1.3.6.1.4.1.4998.1.1.20.1.2 |
cadAgingCPEAgingIntervalMAC Aging counter granularity.rw TimeInterval .1.3.6.1.4.1.4998.1.1.20.1.2.1 |
cadAgingSFAgingIntervalService Flow Aging granularity.rw TimeInterval .1.3.6.1.4.1.4998.1.1.20.1.2.2 |
cadAgingStaleMACAgingIntervalStale MAC Flow Aging time in seconds.rw Integer32 .1.3.6.1.4.1.4998.1.1.20.1.2.3 |
cadAgingArpCacheAgingIntervalArp cache Aging time in seconds.rw Integer32 (0 | 600..360000) -- 10 minutes to 100 hours UNITS "seconds" .1.3.6.1.4.1.4998.1.1.20.1.2.4 |
cadAgingIdleMACAgingIntervalThe timeout period in seconds for aging out
dynamically learned MAC information.rw Integer32 .1.3.6.1.4.1.4998.1.1.20.1.2.5 |
cadAgingArpCacheSearchingRateLimitThe minimum amount of time between transmitting ARP requests while
an ARP cache entry is in the searching state.rw Integer32 .1.3.6.1.4.1.4998.1.1.20.1.2.6 |
cadAgingArpCacheSearchingMaxNumberThe maximum number of ARP requests transmitted while an ARP cache entry
is in the searching state. When the number of ARPs indicated by this
variable have been transmitted, the next packet that arrives for an ARP
cache entry in the searching state will cause that entry to transition to
the notPresent state.rw Integer32 .1.3.6.1.4.1.4998.1.1.20.1.2.7 |
cadAgingArpCacheNotPresentRateLimitThe minimum amount of time between transmitting ICMP unreachables
while an ARP cache entry is in the notPresent state.rw Integer32 .1.3.6.1.4.1.4998.1.1.20.1.2.8 |
cadAgingArpCacheNotPresentMaxNumberThe maximum number of ICMP unreachables transmitted while an ARP cache
entry is in the notPresent state. When the number of ICMPs indicated by
this variable have been transmitted, the next packet that arrives for an
ARP cache entry in the notPresent state will cause that entry to transition
to the searching state, unless cadAgingArpCacheNotPresentMinTime has not
been reached yet.rw Integer32 .1.3.6.1.4.1.4998.1.1.20.1.2.9 |
cadAgingArpCacheNotPresentMaxTimeThe maximum amount of time an ARP cache entry is in the notPresent state.
When the amount of time indicated by this variable has elapsed, the next
packet that arrives for an ARP cache entry in the notPresent state will
cause that entry to transition to the searching state, unless
cadAgingArpCacheNotPresentMinTime has not been reached yet.rw Integer32 .1.3.6.1.4.1.4998.1.1.20.1.2.10 |
cadAgingArpCacheNotPresentMinTimeThe minimum amount of time an ARP cache entry is in the notPresent state.
This variable takes precedence over cadAgingArpCacheNotPresentMaxNumber
and cadAgingArpCacheNotPresentMaxTime. However, and ARP entry aged out
due to inactivity will be removed regardless of whether the amount of
time indicated by cadAgingArpCacheNotPresentMinTime has elapsed or not.rw Integer32 .1.3.6.1.4.1.4998.1.1.20.1.2.11 |
cadAgingArpCacheSearchingGlobalMaxRateThe maximum global ARP request transmit rate for all IP's with an ARP cache
entry in the searching state. Units are in packets sent per second.rw Integer32 .1.3.6.1.4.1.4998.1.1.20.1.2.12 |
cadAgingArpCacheNotPresentGlobalMaxRateThe maximum global ICMP unreachable transmit rate for all IP's with an ARP cache
entry in the notPresent state. Units are in packets sent per second.rw Integer32 .1.3.6.1.4.1.4998.1.1.20.1.2.13 |
cadAgingNDCacheAgingIntervalND cache Aging time in seconds.rw Integer32 (0 | 180..360000) -- 5 minutes to 100 hours UNITS "seconds" .1.3.6.1.4.1.4998.1.1.20.1.2.14 |
cadAgingNDCacheSearchingRateLimitThe minimum amount of time between transmitting ND requests while
an ND cache entry is in the searching state.rw Integer32 .1.3.6.1.4.1.4998.1.1.20.1.2.15 |
cadAgingNDCacheSearchingMaxNumberThe maximum number of ND requests transmitted while an ND cache entry
is in the searching state. When the number of NDs indicated by this
variable have been transmitted, the next packet that arrives for an ND
cache entry in the searching state will cause that entry to transition to
the notPresent state.rw Integer32 .1.3.6.1.4.1.4998.1.1.20.1.2.16 |
cadAgingNDCacheNotPresentRateLimitThe minimum amount of time between transmitting ICMP unreachables
while an ND cache entry is in the notPresent state.rw Integer32 .1.3.6.1.4.1.4998.1.1.20.1.2.17 |
cadAgingNDCacheNotPresentMaxNumberThe maximum number of ICMP unreachables transmitted while an ND cache
entry is in the notPresent state. When the number of ICMPs indicated by
this variable have been transmitted, the next packet that arrives for an
ND cache entry in the notPresent state will cause that entry to transition
to the searching state, unless cadAgingNDCacheNotPresentMinTime has not
been reached yet.rw Integer32 .1.3.6.1.4.1.4998.1.1.20.1.2.18 |
cadAgingNDCacheNotPresentMaxTimeThe maximum amount of time an ND cache entry is in the notPresent state.
When the amount of time indicated by this variable has elapsed, the next
packet that arrives for an ND cache entry in the notPresent state will
cause that entry to transition to the searching state, unless
cadAgingNDCacheNotPresentMinTime has not been reached yet.rw Integer32 .1.3.6.1.4.1.4998.1.1.20.1.2.19 |
cadAgingNDCacheNotPresentMinTimeThe minimum amount of time an ARP cache entry is in the notPresent state.
This variable takes precedence over cadAgingArpCacheNotPresentMaxNumber
and cadAgingArpCacheNotPresentMaxTime. However, and ARP entry aged out
due to inactivity will be removed regardless of whether the amount of
time indicated by cadAgingArpCacheNotPresentMinTime has elapsed or not.rw Integer32 .1.3.6.1.4.1.4998.1.1.20.1.2.20 |
cadAgingNDCacheSearchingGlobalMaxRateThe maximum global ND request transmit rate for all IP's with an ND cache
entry in the searching state. Units are in packets sent per second.rw Integer32 .1.3.6.1.4.1.4998.1.1.20.1.2.21 |
cadAgingNDCacheNotPresentGlobalMaxRateThe maximum global ICMP unreachable transmit rate for all IP's with an ND cache
entry in the notPresent state. Units are in packets sent per second.rw Integer32 .1.3.6.1.4.1.4998.1.1.20.1.2.22 |
cadAgingArpCacheSearchingCableUnicastThe maximum number of unicast ARP requests transmitted while an ARP
cache entry is in the searching state where the MAC/IP binding is previously
known. After the number of unicast ARPs indicated by this variable have
been transmitted, additional ARP requests will be sent as broadcast until the
cadAgingArpCacheSearchingMaxNumber limit is reached, at which point the
next packet that arrives for an ARP cache entry in the searching state will
cause that entry to transition to the notPresent state.rw Integer32 .1.3.6.1.4.1.4998.1.1.20.1.2.23 |
cadAgingArpCacheSearchingCableBroadcastThis variable controls whether broadcast ARP packets can be sent for an
IPv4 address where there is no stored previous knowledge about a MAC/IP
binding. The total number of broadcast ARPs to send before switching to the
not-present state is limited by the cadAgingArpCacheSearchingMaxNumber
variable. If cadAgingArpCacheSearchingCableBroadcast is false and there is
no stored previous knowledge about a MAC/IP binding, the ARP cache entry
will transition immediately to the not-present state.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.2.24 |
cadAgingNDCacheSearchingCableUnicastThe maximum number of unicast NS requests transmitted while an ND
cache entry is in the searching state where the MAC/IP binding is previously
known. After the number of unicast NSs indicated by this variable have
been transmitted, additional NS requests will be sent as multicast until the
cadAgingNDCacheSearchingMaxNumber limit is reached, at which point the
next packet that arrives for an ND cache entry in the searching state will
cause that entry to transition to the notPresent state.rw Integer32 .1.3.6.1.4.1.4998.1.1.20.1.2.25 |
cadAgingNDCacheSearchingCableMulticastThis variable controls whether multicast NS packets can be sent for an
IPv6 address where there is no stored previous knowledge about a MAC/IP
binding. The total number of multicast NSs to send before switching to the
not-present state is limited by the cadAgingNDCacheSearchingMaxNumber
variable. If cadAgingNDCacheSearchingCableMulticast is false and there is
no stored previous knowledge about a MAC/IP binding, the ND cache entry will
transition immediately to the not-present state.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.2.26 |
cadLayer2MibGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4998.1.1.20.1.3 |
cadMacPortMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4998.1.1.20.1.4 |
cadMacPortTableMAC port table. SEQUENCE OF CadMacPortEntry .1.3.6.1.4.1.4998.1.1.20.1.4.1 |
cadMacPortEntry CadMacPortEntry .1.3.6.1.4.1.4998.1.1.20.1.4.1.1 |
cadMacPortIdMAC port id which uniquely identifies a MAC port. Mac port Id range from 417 to 448 are reserved for
2D12U CAMs. MacPortId (CADANT-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.1.1.1 |
cadMacPortAdminStateThe administrative state of the MAC port.rw AdminState (CADANT-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.1.1.4 |
cadMacPortPrStateThe primary state of the MAC port.ro PrimaryState (CADANT-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.1.1.5 |
cadMacPortSecStateThe secondary state of the MAC port.ro SecondaryState (CADANT-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.1.1.6 |
cadMacPortDplxStatusThe duplex status of the MAC port.ro DuplexStatus (CADANT-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.1.1.7 |
cadMacPortMacAddressThe MAC address of the MAC port.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.1.1.8 |
cadMacPortIfIndexThe ifIndex of the MAC port.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4998.1.1.20.1.4.1.1.9 |
cadMacPortDescriptionThe description of the MAC port.rw DisplayString .1.3.6.1.4.1.4998.1.1.20.1.4.1.1.10 |
cadMacPortTrapInhIf a bit is set, the corresponding state change trap will not be sent.
By default only linkUp and linkDown notifications are enabled.rw Bits .1.3.6.1.4.1.4998.1.1.20.1.4.1.1.11 |
cadMacPortRowStatusControl object for row creation and deletion.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.1.1.12 |
cadMacPortOfdmIf set to true, DOCSIS 3.1 is enabled for this MAC Port.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.1.1.13 |
cadIfMacDomainTableThe cadIfMacDomainTable maintains configuration information specific to
each MAC domain. The table is indexed by the MAC domain ifIndex(from the
ifTable or the cadMacPortTable). SEQUENCE OF CadIfMacDomainEntry .1.3.6.1.4.1.4998.1.1.20.1.4.2 |
cadIfMacDomainEntry CadIfMacDomainEntry .1.3.6.1.4.1.4998.1.1.20.1.4.2.1 |
cadIfMacDomainIfIndexMAC domain ifIndex InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.1 |
cadIfMacDomainCapabilitiesIdentifies the capabilities of the CMTS MAC implementation at this interface.ro Bits .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.2 |
cadIfMacDomainSyncIntervalInterval between CMTS transmission of successive SYNC messages at this interface.rw Integer32 .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.3 |
cadIfMacDomainUcdIntervalInterval between CMTS transmission of successive UCD messages for each
upstream at this interface.rw Integer32 .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.4 |
cadIfMacDomainMaxServiceIdsMaximum number of service IDs that may be simultaneously active.ro Integer32 .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.5 |
cadIfMacDomainInvitedRangingAttemptsMaximum number of attempts to make on invitations for
ranging requests. A value of 0 means the system should
attempt to range forever.rw Integer32 .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.6 |
cadIfMacDomainInsertIntervalAmount of time between each broadcast station maintenance grant.rw INTEGER .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.7 |
cadIfMacDomainRangingIntervalAmount of time to elapse between each ranging message.rw TimeInterval .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.8 |
cadIfMacDomainRangeOpportunityCycleAmount of time to elapse between each ranging cycle.rw TimeInterval (100.. 500) UNITS "Centiseconds" .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.9 |
cadIfMacDomainTftpEnforceCurrent state of TFTP enforce for this interface.rw CadTftpEnforceType .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.10 |
cadIfMacDomainDynamicSecretCurrent state of Cable Dynamic Secret for this interface.rw CadDynamicSecretType .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.11 |
cadIfMacDomainAnnexThe value of this object indicates the conformance of
the implementation to important regional cable standards.
annexA : Annex A from ITU-J83 is used.
annexB : Annex B from ITU-J83 is used.
annexC : Annex C from ITU-J83 is used.rw Enumeration .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.13 |
cadIfMacDomainMddIntervalThis attribute configures the interval for the insertion of MDD messages in each downstream channel of a MAC Domain.rw Unsigned32 .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.14 |
cadIfMacDomainIpProvModeThis attribute configures the CMTS IP provisioning mode for a MAC Domain.
When this attribute is set to 'ipv4Only' the CM will acquire a single IPv4 address
for the CM management stack. When this attribute is set to 'ipv6Only' the CM will acquire
a single IPv6 address for the CM management stack. When this attribute is set to 'alternate'
the CM will acquire a single IPv6 address for the CM management stack and, if failures occur,
the CM will fall back to provisioning and operation with an IPv4 address.
When this attribute is set to 'dualStack' the CM will acquire both an IPv6 and IPv4 address
for provisioning and operation.rw Enumeration .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.16 |
cadIfMacDomainCmStatusEvCtlEnabledIf set to 'true', this attribute enables the
signaling of the CM-Status Event reporting mechanism.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.18 |
cadIfMacDomainUsFreqRangeThis attribute indicates in MDD messages the
upstream frequency upper band edge of an upstream
Channel. A value 'standard' means Standard Frequency
Range and a value 'extended' means Extended Frequency Range.rw Enumeration .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.19 |
cadIfMacDomainMcastDsidFwdEnabledIf set to 'true', this attribute enables the
CMTS to use IP Multicast DSID Forwarding (MDF) for the MAC domain.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.20 |
cadIfMacDomainDsBondingEnabledIf set to 'true', this attribute enables
Downstream Channel Bonding for the MAC Domain.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.21 |
cadIfMacDomainMultTxChModeEnabledIf set to 'true', this attribute enables
Multiple Transmit Channel (MTC) Mode for the MAC Domain.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.22 |
cadIfMacDomainEarlyAuthEncrCtrlThis attribute enables or disables early
authentication and encryption (EAE) signaling for the
MAC Domain. It also defines the type of EAE
enforcement in the case that EAE is enabled. If set to
'disableEAE', EAE is disabled for the MAC Domain. If
set to 'enableEaeRangingBasedEnforcement',
'enableEaeCapabilityBasedEnforcement' or
'enableEaeTotalEnforcement', EAE is enabled for the
MAC Domain.
The following EAE enforcement methods are defined in
the case where EAE signaling is enabled:
The option 'enableEaeRangingBasedEnforcement'
indicates EAE is enforced on CMs that perform ranging
with a B-INIT-RNG-REQ message.
The option 'enableEaeCapabilityBasedEnforcement'
indicates EAE is enforced on CMs that perform ranging
with a B-INIT-RNG-REQ message in which the EAE
capability flag is set.
The option 'enableEaeTotalEnforcement' indicates EAE
is enforced on all CMs regardless of their EAE
capabilities.rw Enumeration .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.23 |
cadIfMacDomainTftpProxyEnabledIf set to 'true', this attribute enables TFTP
Proxy functionality for the MAC Domain.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.24 |
cadIfMacDomainSrcAddrVerifEnabledIf set to 'true', this attribute enables Source
Address Verification (SAV) functionality for the MAC Domain.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.25 |
cadIfMacDomainMulticastEncryptionIf set to 'true', this attribute enables multicast encryption
for all multicast flows on all downstream channels in the MAC domain
using the des56 algorithm.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.26 |
cadIfMacDomainRcpReportModeThis attribute controls the reporting of the CM receiver profiles
in the registration messages. A value of 0 means that the CM MUST NOT provide verbose
reporting of all its Receive Channel Profiles. A value of 1 means that the CM MUST
provide verbose reporting of Receive Channel Profiles. both standard profiles and
manufacturers profiles.rw Enumeration .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.27 |
cadIfMacDomainRegRspToOverrideThis attribute provides an ability to override the default value of the T6 timer in the CM.
When this attribute is not set to its default value, then the CMTS will place it into
the MDD and the CM MUST use this value in place of the default value for the T6 timer.rw Unsigned32 .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.28 |
cadIfMacDomainMultRxChModeEnabledIf set to true, this attribute enables Downstream Channel Bonding for the MAC Domain.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.29 |
cadIfMacDomainCmUdcEnabledIf set to true, this attribute instructs the CMTS MAC Domain to enable Upstream Drop Classifiers (UDC)
for the CMs attempting registration in this MAC Domain.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.30 |
cadIfMacDomainSendUdcRulesEnabledIf set to true and when the CM signals to the CMTS 'Upstream Drop Classifier Group ID encodings,
this attribute instructs the CMTS MAC Domain to send the Subscriber Management Filters rules
associated with the Upstream Drop Classifier Group ID encodings to the CM in the form of UDCs
when the following conditions occurs: 1)The attribute CmUdcEnabled value for this MAC Domain is set to true,
and 2)The CM has the UDC capability advertised as supported. If there is no a single
Subscriber Management Filter configured in the CMTS for the CM signaled UDC Group ID,
the CMTS does not send UDC encodings to the CM. It is vendor specific whether the CMTS maintains
enforcement of the CM signaled or default Subscriber Management Filter groups in the upstream direction.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.31 |
cadIfMacDomainRccDynEnableThis object allows user to enable or disable the autonomous creation of dynamic RCCs per mac domain.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.32 |
cadIfMacDomainDsbgDynEnableThis object allows user to enable or disable the autonomous creation of dynamic bonding groups per mac domain.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.33 |
cadIfMacDomainDsbgReseqWaitTimeResequence wait time to se set for dynamic bonding groups per mac domain. If the value 255 indicates that requence wait time
is determined by the CMTS.rw Unsigned32 (1..180 | 255) UNITS "hundredMicroseconds" .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.34 |
cadIfMacDomainDsbgReseqWarnThrshldResequence warning threshold to se set for dynamic bonding groups per mac domain. If the value 255 indicates that requence
warning threshold is determined by the CMTS.rw Unsigned32 (0..179 | 255) UNITS "hundredMicroseconds" .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.35 |
cadIfMacDomainDpIdWhen a mac domain is created or system reset, DMM assigns a Downstream Pool ID (DPID) for each mac domain. If the value 255
indicates the DPID is invalid.ro Integer32 (0..15 | 255) .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.36 |
cadIfMacDomainUsbgDynEnableThis object allows user to enable or disable the autonomous creation of dynamic upstream bonding groups per mac domain.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.37 |
cadIfMacDomainDownChannelMaxFrequencyThis object is used to configure the C4 CMTS to accept maximum downstream
frequency limit that conform with the EuroDOCSIS specifications
(starndard range 112 MHz to 858 MHz), (extended 85 MHz to 999MHz)
or to the DOCSIS specifications (standard 91 to 867 MHz), (extended range 57 MHz to 999 MHz).
Changes to downstream frequency and width are verified against this
object to ensure the C4 CMTS does not exceed the downstream spectrum
limits imposed by this object. Attempting to decrease the downstream
frequency spectrum implied by this object will fail if at least
a single downstream is configured outside of the range for the new
value. It is recommended this object be set during initial system
setup.rw INTEGER (858000000 | 867000000 | 999000000) UNITS "hertz" .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.38 |
cadIfMacDomainDownChannelMinFrequencyThis object is used to configure the C4 CMTS to accept minimum downstream
frequency limit that conform with the EuroDOCSIS specifications
(starndard range 112 MHz to 858 MHz), (extended 85 MHz to 999MHz)
or to the DOCSIS specifications (standard 91 to 867 MHz), (extended range 57 MHz to 999 MHz).
Changes to downstream frequency and width are verified against this
object to ensure the C4 CMTS does not exceed the downstream spectrum
limits imposed by this object. Attempting to increase the minimum downstream
frequency limit implied by this object will fail if at least
a single downstream is configured outside of the range for the new
value. It is recommended this object be set during initial system
setup.rw INTEGER (57000000 | 85000000 | 91000000 | 112000000) UNITS "hertz" .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.39 |
cadIfMacDomainUpChannelMaxFrequencyThis object is used to configure the C4 CMTS to accept upstream
frequency ranges that conform with the EuroDOCSIS specifications
(5 MHz to 65 MHz), to the extended range used in Japan
(5 MHz to 55 MHz), or to the DOCSIS specifications (5 MHz to 42 MHz),
or to the extended upstream range (5 MHz to 85 MHz).
Changes to upstream frequency and width are verified against this
object to ensure the C4 CMTS does not exceed the upstream spectrum
limits imposed by this object. Attempting to narrow the upstream
frequency spectrum implied by this object will fail if at least
a single upstream is configured outside of the range for the new
value. Default value is taken from global setting when the cable-mac
is created.rw INTEGER ( 42000000 | 55000000 | 65000000 | 85000000) UNITS "hertz" .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.40 |
cadIfMacDomainBpi2MandatoryThis object determines the what minimum level of
BPI operation is required in order to allow a cable
modem to register.rw Enumeration .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.41 |
cadIfMacDomainDSG30EnabledIf set to 'true', this attribute enables the
CMTS to use DSG3.0 on the MAC domain. If false,
then DSG reverts to the pre-DOCSIS3.0 version
without DSIDs.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.43 |
cadIfMacDomainEnforceRulesEnabledIf set to 'true', then QOS penalties as defined in the
cadEnforceRuleTable will be enforced for SFs on CMs
in this MAC Domain.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.44 |
cadIfMacDomainCmTxPwrExtentionPreRegistrationEnabledIndicate if the transmit power extension (before registration) feature
is enabled or not onthe CMTS. If set to 'true', the CMTS will populate
TLV16 in the MDD message with the value of 1. If set to 'false',
the CMTS will populate TLV16 in the MDD message with the the value of 0.
The value in this MIB object is ignored if MTCM is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.45 |
cadIfMacDomainCmTxPwrExtentionPostRegistrationEnabledIndicate if the transmit power extension (after registration) feature
is enabled or not on the CMTS. If set to 'true', the CMTS will populate
TLV5.40 in the REG-RSP-MP message with the same value received in the
REG-REQ-MP message (advertised CM capability). If set to 'false',
the CMTS will respond with 0 in TLV5.40 of the REG-RSP-MP message.
The value in this MIB object is ignored if MTCM is disabledrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.46 |
cadIfMacDomainT4TimeoutMultiplierEnabledIf set to true, this attribute instructs the CMTS MAC Domain to enable the T4 Timeout
Multiplier for the CMs operating in MTCM in this MAC Domain. The multiplier will be
set equal to the number of upstream assigned to the modem at registration time.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.47 |
cadIfMacDomainDynamicRccMultiTunerEnabledIf set to true, this attribute instructs the CMTS MAC Domain to
enable dynamic RCC support for CM RCP's with multiple tuners.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.48 |
cadIfMacDomainTcsSizeLimitThis object is used to potentially limit the number of channels within
a CM's TCS. A value of 0 indicates the limit is determined by the CM's
capabilities, configuration and operational status. When a non-zero value
is specified and is smaller than the number of channels that are capable of
residing within the CM's TCS, the number of channels within the CM's TCS
will be restricted to the specified value.rw Integer32 .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.49 |
cadIfMacDomainDocsis31EnabledIf set to true, DOCSIS 3.1 is enabled for this MAC Domain.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.50 |
cadIfMacDomainEnergyMgt1x1EnabledThis attribute indicates whether the CMTS is configured
for 1x1 Energy Management Mode of operation on a per
MAC Domain basis. If this attribute is set to 'true',
the CMTS is configured for 1x1 Energy Management Mode
of operation on this MAC Domain. If this attribute is
set to 'false', the Energy Management 1x1 Mode of
operation is disabled in the CMTS on this MAC Domainrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.51 |
cadIfMacDomainDsOfdmProfileRecoveryGuardTimeThe amount of time that an impaired OFDM profile will remain impaired before
transitioning to good upon being notified that the CM can decode the profile. This provides
some hysteresis for a profile to become stable before using the newly decodable profile. If set
to a value of 0, then there is no hysteresis (no timer is started) and all profiles may transition
to good immediately upon being notified that the CM can decode the profile.rw Integer32 .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.52 |
cadIfMacDomainGracefulTcsReductionEnabledIf set to true, the CMTS will instruct the
modem to try incrementally lower numbers of bonded
channels instead of reverting immediately to single
US bonded channel while registering a modem and a
power shortfall or DRW violation is encountered.
If set to false, the CMTS will instruct the
modem to immediately revert to a single US bonded
channel while registering a modem and a power shortfall
or DRW violation is encountered.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.2.1.53 |
cadMacChlTableMAC channel table. SEQUENCE OF CadMacChlEntry .1.3.6.1.4.1.4998.1.1.20.1.4.3 |
cadMacChlEntry CadMacChlEntry .1.3.6.1.4.1.4998.1.1.20.1.4.3.1 |
cadMacChlMacDomainIfIndexifIndex of the MAC domain InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4998.1.1.20.1.4.3.1.1 |
cadMacChlChannelIfIndexifIndex of the upstream or downstream channel InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4998.1.1.20.1.4.3.1.2 |
cadMacChlCardNumbercard number of downstream or upstream channelro CardId (CADANT-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.3.1.3 |
cadMacChlPortIdport Id of downstream or upstream channelro PortId (CADANT-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.3.1.4 |
cadMacChlPortTypeport type of downstream or upstream channelro PortType (CADANT-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.3.1.5 |
cadMacChlCardSubTypecard subtype type of downstream or upstream channelro CerCardSubType (CADANT-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.3.1.6 |
cadMacChlChannelIddownstream or upstream channel ID. 0 is an invalid channel Id.rw Integer32 .1.3.6.1.4.1.4998.1.1.20.1.4.3.1.7 |
cadMacChlRowStatusControl object for row creation and deletionrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.3.1.8 |
cadMacChlIsPriCapableDsTrue if this is downstream channel and it is intended to be used
as a primary channel by one or more cable modems. False otherwise.
When a row's cadMacChlIsPrimaryCapableDs column is set to true(1)
then DOCSIS SYNC message generation is enabled on the downstream
channel.
The default value of this field is true(1) for all downstream
channels and false(2) for all upstream channels.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.3.1.9 |
cadMacChlSfProvAttrMaskProvisioned attributes of this channel for purposes of channel
assignment.rw AttributeMask (DOCS-IF3-MIB) .1.3.6.1.4.1.4998.1.1.20.1.4.3.1.10 |
cadMacChlDirectionDOCSIS downstream or upstream direction.ro IfDirection (DOCS-IF3-MIB) .1.3.6.1.4.1.4998.1.1.20.1.4.3.1.11 |
cadUpSupervisionCfgTableUpstream supervison configuration table. SEQUENCE OF CadUpSupervisionCfgEntry .1.3.6.1.4.1.4998.1.1.20.1.4.4 |
cadUpSupervisionCfgEntry CadUpSupervisionCfgEntry .1.3.6.1.4.1.4998.1.1.20.1.4.4.1 |
cadUpSupervisionCfgUpChannelIfIndexifIndex of the upstream logical channel. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4998.1.1.20.1.4.4.1.1 |
cadUpSupervisionCfgDownChannelIfIndexifIndex of the downstream channel. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4998.1.1.20.1.4.4.1.2 |
cadUpSupervisionCfgAssignIndicates whether supervisory information for the upstream channel
with cadIfUpChannelIfIndex is to be carried on the downstream channel
with cadIfDownChannelIfIndex.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.4.1.3 |
cadUpSupervisionCfgRowStatusControl object for row creation and deletion.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4998.1.1.20.1.4.4.1.4 |
cadUpSupervisionStatusTableUpstream supervision stataus table. SEQUENCE OF CadUpSupervisionStatusEntry .1.3.6.1.4.1.4998.1.1.20.1.4.5 |
cadUpSupervisionStatusEntry CadUpSupervisionStatusEntry .1.3.6.1.4.1.4998.1.1.20.1.4.5.1 |
cadUpSupervisionStatusUpChannelIfIndexifIndex of the upstream logical channel. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4998.1.1.20.1.4.5.1.1 |
cadUpSupervisionStatusDownChannelIfIndexifIndex of the downstream channel. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4998.1.1.20.1.4.5.1.2 |
cadUpSupervisionStatusAssignmentMethodOrigin of the supervisory relationship.ro Enumeration .1.3.6.1.4.1.4998.1.1.20.1.4.5.1.3 |
arrisCerIpGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4998.1.1.20.1.5 |
cerIpGratuitousArpPeriodConfigure the global time in seconds between gratuitous ARP transmission.rw Unsigned32 .1.3.6.1.4.1.4998.1.1.20.1.5.1 |