Home/Catalog/CADANT-CMTS-EQUIPMENT-MIB

CADANT-CMTS-EQUIPMENT-MIB

AI MIB Summary

The CADANT-CMTS-EQUIPMENT-MIB facilitates the remote provisioning, diagnostic testing, and auditing configuration of Arris E6 Cable Modem Termination System (CMTS) hardware, specifically managing card and port states while handling equipment-related trap notifications.

This MIB is intended to describe all objects which are used to control and report on the state of an Arris E6 CMTS. These objects are used to perform the following functions on an Arris E6 CMTS: a) provision the cards, ports, and the CMTS itself b) run dianostic tests c) configure auditing parameters d) receive equipment-related traps
Main OID:
cadEquipmentMib.1.3.6.1.4.1.4998.1.1.10.1
246
Objects
Active
Status
8
Dependencies

Imported Objects

CADANT-PRODUCTS-MIB
CADANT-TC
DOCS-IF-MIB
IF-MIB
SNMP-FRAMEWORK-MIB
SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC

Objects

246 total
Object Name
cadEquipmentMibThis MIB is intended to describe all objects which are used to control and report on the state of an Arris E6 CMTS. These objects are used to perform the following functions on an Arris E6 CMTS: a) provision the cards, ports, and the CMTS itself b) run dianostic tests c) configure auditing parameters d) receive equipment-related traps
MODULE-IDENTITY
.1.3.6.1.4.1.4998.1.1.10.1
equipmentTraps
OBJECT IDENTIFIER
.1.3.6.1.4.1.4998.1.1.10.1.0
cmResetClearNotificationThis trap is sent when a CM is on-line from previous flap.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4998.1.1.10.1.0.15
cmResetNotificationThis trap is sent when a CM is reset.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4998.1.1.10.1.0.16
cardTempOutOfRangeNotificationThis trap is sent when the card temperature is out of range.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4998.1.1.10.1.0.19
cardTempNoReportNotificationThis trap is sent when there is no reporting on card temperature.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4998.1.1.10.1.0.20
cardTempOverHeatNotificationThis trap is sent when the card is overheat, card is being shut down.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4998.1.1.10.1.0.21
downstreamPowerLossThis trap is sent when c4 detects the loss of downstream power.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4998.1.1.10.1.0.22
cmRegistrationNotificationThis trap is sent when a CM is registered.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4998.1.1.10.1.0.23
noLicenseNotificationThis trap is sent when a channel cannot be activated due to insufficient license level.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4998.1.1.10.1.0.24
cerCardPrStateChangeThis trap is sent whenever the card's Primary state changes.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4998.1.1.10.1.0.25
cerCardSecStateChangeThis trap is sent whenever the card's Secondary state changes.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4998.1.1.10.1.0.26
cerCardDetectedChangeThis trap is sent whenever a new card is detected.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4998.1.1.10.1.0.27
cerCardDplxStatusChangeThis trap is sent whenever the card's Duplex status changes.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4998.1.1.10.1.0.28
cerPortPrStateChangeThis trap is sent whenever the port's Primary state changes.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4998.1.1.10.1.0.29
cerPortSecStateChangeThis trap is sent whenever the port's Secondary state changes.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4998.1.1.10.1.0.30
cerPortDplxStatusChangeThis trap is sent whenever the port's Duplex status changes.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4998.1.1.10.1.0.31
cardTestResultNotificationThis trap is sent when a test or diagnostic completed on a card.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4998.1.1.10.1.0.33
cerDiskVolumeUsageNotificationThis trap is sent when a disk volume usage level exceed a disk usage threshold.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4998.1.1.10.1.0.35
cerDiskVolumeAutoDeleteFileNotificationThis trap is sent when a file is automatically deleted by the system in respond to disk volume usage exceed critical thresholh.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4998.1.1.10.1.0.36
cerCamFaultInfo
OBJECT IDENTIFIER
.1.3.6.1.4.1.4998.1.1.10.1.0.40
cerCamFaultIdType of CAM fault trigging the trap.ro
CerCamFaultTrapType
.1.3.6.1.4.1.4998.1.1.10.1.0.40.1
cerCamFaultRecoveryTrue if recovery for this event is enabled.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.0.40.2
cerCamFaultAutoFailbackTrue if autofailback is enabled and the maximum failbacks have not occurred.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.0.40.3
cerCamFaultErrorStrExtra information about this error. Null string if no extra info.ro
DisplayString
.1.3.6.1.4.1.4998.1.1.10.1.0.40.4
cerCamFaultNotificationThis trap is sent when a CAM has a fault of the specified type, even if fault recovery is inhibited for that fault type.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4998.1.1.10.1.0.41
systemGeneral
OBJECT IDENTIFIER
.1.3.6.1.4.1.4998.1.1.10.1.1
systemClockCMTS local date and time displayed as yyyy-mm-dd,hh:mm:ss.d,+/-hh:mm, where the date is yyyy-mmmm-dd and time in deci-seconds is hh:mm:ss.d, adn teh current offset from GMT is +/-hh:mm. This object is adjusted by teh TZ and DST rules. E.g. 2002-5-26,13;30:15.0,-4:0ro
DateAndTime (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.1.1
trapCounterThis is the trap sequence number that increments each time a trap is sent. It is persistent across resets.ro
Counter32
.1.3.6.1.4.1.4998.1.1.10.1.1.2
trapSeveritySeverity level of a Cadant trap.ro
Enumeration
.1.3.6.1.4.1.4998.1.1.10.1.1.3
systemKeyThe systemKey is a unique string used for Candant's CMTS identification. The EMS uses this key string as well as the sysOid in the MIB-II system group MIB to identify Candant's CMTS's.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.1.4
cardNumberCard Id used in traps. A value 99 indicates an invalid cardNumber.ro
CardId (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.1.98
portNumberPort Id used in traps. A value of 99 indicates an invalid portNumber.ro
PortId (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.1.99
diskDriveNumberDisk drive ID use in a Cadant trap. A value of 99 indicates an invalid diskDriveNumberro
Integer32
.1.3.6.1.4.1.4998.1.1.10.1.1.100
diskVolumeNumberDisk volume ID use in a Cadant trap. A value of 99 indicates an invalid diskVolumeNumberro
Integer32
.1.3.6.1.4.1.4998.1.1.10.1.1.101
cerCardNumberCard Id used in traps. A value 0 indicates an invalid cardNumber.ro
CardId (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.1.200
cerPortNumberPort Id used in traps. A value of 0 indicates an invalid portNumber.ro
PortId (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.1.201
cerDiskDriveNumberDisk drive ID use in a Cadant trap. A value of 0 indicates an invalid diskDriveNumberro
Integer32
.1.3.6.1.4.1.4998.1.1.10.1.1.202
cerDiskVolumeNumberDisk volume ID use in a Cadant trap. A value of 0 indicates an invalid diskVolumeNumberro
Integer32
.1.3.6.1.4.1.4998.1.1.10.1.1.203
shelfObjects
OBJECT IDENTIFIER
.1.3.6.1.4.1.4998.1.1.10.1.2
shelfNameA string that represents the name of this machine and may uniquely identify it from other network devices.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.2.2
shelfSwVersionThe software version currently executing.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.2.3
equipmentState
OBJECT IDENTIFIER
.1.3.6.1.4.1.4998.1.1.10.1.3
cardLastChangeTimeThe value of sysUpTime at the time any of the objects in cardTable last changed.ro
TimeStamp (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.3.2
portLastChangeTimeThe value of sysUpTime at the time any of the objects in portTable last changed.ro
TimeStamp (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.3.3
equipmentTbl
OBJECT IDENTIFIER
.1.3.6.1.4.1.4998.1.1.10.1.4
cerCardTableA table of card or circuit pack information.
SEQUENCE OF CerCardEntry
.1.3.6.1.4.1.4998.1.1.10.1.4.12
cerCardEntryA conceptual row containing pertinent information about a card or a circuit pack.
CerCardEntry
.1.3.6.1.4.1.4998.1.1.10.1.4.12.1
cerCardIdThe unique id of this card within the shelf. The convention of cardId is as follows: - Indices from 1 to 50 [1 - 50] are reserved for Circuit Packs. In this case, the cardId is 1 plus the 0-based slot number. - Indices from 51 to 98 [51 - 98] are reserved for Auxilliary Devices in within a shelf. Auxilliary Devices or Modules could be Fan Module, Power Module. In this case, the cerCardName and cerCardType indentify the Auxilliary Devices. Not all of row attributes are applicable for Auxilliary Devices.ro
CardId (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.2
cerCardNameThis is the name of the card, if it has one.rw
DisplayString
.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.3
cerCardTypeThe type of card, if any. For example Ecard, Fcard, Dcard or Ucard If the slot is empty, the value would be 'empty'.ro
CerCardType (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.4
cerCardSubTypeThe cardType alone may not be specific enough to fully describe the type of card that is in this slot. For example, a card type of Dcard might have a more specific type of 1D8U with integrated upconverter. If the card needs no further specificication that the cardType, then the value of cardSubType is 'none'. Not yet implemented.rw
CerCardSubType (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.5
cerCardAdminStateThis is the administrative state of this card.rw
AdminState (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.12
cerCardPrStateThis is the primary state of this card.ro
PrimaryState (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.13
cerCardSecStateThis is the secondary state of this card.ro
SecondaryState (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.14
cerCardDplxStatusThis is the duplexing status of this card.ro
DuplexStatus (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.15
cerCardActionWrite-only action performed on this card.rw
EqActionType (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.17
cerCardTrapInhIf a bit is set, the corresponding state change trap will not be sent.rw
Bits
.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.18
cerCardNumPortsNumber of ports this card contains.ro
Integer32
.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.19
cerCardDetectedCardType dectected automatically by the CMTS.ro
CerCardType (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.20
cerCardSubDetectedCardSubType dectected automatically by the CMTS.ro
CerCardSubType (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.21
cerCardFwUpdateStatusSet to TRUE if a firmware update is in progress or has been done, else set to FALSE.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.23
cerCardSpareGroupIdThe cardId of the spare group leader for this sparing group. This value will be set to the invalid card id for all cards not associated with a sparing group.rw
CardId (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.24
cerCardSpareGroupModeThe admin mode of the spare group leader for this sparing group. This value will be set to the invalid card id for all cards not associated with a sparing group.rw
Enumeration
.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.25
cerCardUpTimeThe value of sysUpTime when the primary state for this card made a transition from OOS to IS.ro
TimeTicks (SNMPv2-SMI)
.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.26
cerCardTemperatureThe current relative temperature of the card. (1=coolest, 10=hottest)ro
Integer32 (1..10|999)
.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.29
cerCardPicDetectedThe type of PIC detected in this slot.ro
CerPicType (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.40
cerCardLastResetReasonThe reason for the latest card recovery.ro
DisplayString
.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.43
cerCardTemperatureHighWarnThe relative temperature of the card at which warnings are generated.rw
Integer32
.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.44
cerCardTemperatureHighErrorThe relative temperature of the card at which recoveries are initiated.rw
Integer32
.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.45
cerCardAnnexThe annex of the downstream channels associated with the card.ro
Enumeration
.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.46
cerCardNumRfConnectorsNumber of RF ports this card contains.ro
Integer32
.1.3.6.1.4.1.4998.1.1.10.1.4.12.1.47
cerPortTableA table of Port information.
SEQUENCE OF CerPortEntry
.1.3.6.1.4.1.4998.1.1.10.1.4.13
cerPortEntryA conceptual row containing pertinent information about a cerPort owned by a card.
CerPortEntry
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1
cerPortCardIdThe unique id of the card this cerPort belongs to.
CardId (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.2
cerPortIdThe unique id of this cerPort within a card. the the cardId and cerPortId uniquely identify a port
PortId (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.3
cerPortTypeType of this cerPort.rw
CerPortType (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.4
cerPortAdminStateThe Admin state of this cerPortrw
AdminState (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.6
cerPortPrStateThe primary state of this cerPortro
PrimaryState (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.7
cerPortSecStateThe secondary state of this cerPortro
SecondaryState (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.8
cerPortDplxStatusThe port Duplexing status.ro
DuplexStatus (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.9
cerPortActionWrite-only action performed on a Port.rw
EqActionType (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.11
cerPortTrapInhIf a bit is set, the corresponding state change trap will not be sent.rw
Bits
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.12
cerPortNumChansNumber of channels this cerPort contains.ro
Integer32
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.13
cerPortDocsIfIndexThis object indicates the location of an interface in the cerPort table that represents this port. A value of 0 indicates that this cerPort does not have an association in the Iftable.ro
InterfaceIndexOrZero (IF-MIB)
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.14
cerPortMacAddressThe physical address value for this card. This value is used to populate the ifPhysAddress field in the IfTable and other Tables in docsis RFC MIBs.ro
MacAddress (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.15
cerPortModeThe desired operating mode of an ethernet cerPort. Not yet implemented.rw
PortMode (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.16
cerPortDetectedModeThe current operating mode of an ethernet cerPort.ro
PortDetectedMode (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.17
cerPortBgpIdThe bridge group cerPort id for this port.ro
Integer32 (-2147483647..2147483647)
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.19
cerPortConnectorIdFor a DOCSIS or EQAM type port, this is the rear PIC connector. Otherwise, the value of this object is invalid.rw
PortId (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.20
cerPortCardSubTypeThe CardSubType of the card this cerPort belongs to.ro
CerCardSubType (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.21
cerPortDescriptionA persistent copy of ifAlias for this interface.rw
DisplayString
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.27
cerPortCurrDsPowerThe latest downstream power level reported by the port. This is valid on for ports of type dport.ro
TenthdBmV
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.28
cerPortMinDsPowerThe latest downstream power level recerPorted by the port. This is valid only for downstream ports.ro
TenthdBmV
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.29
cerPortMaxDsPowerThe latest downstream power level recerPorted by the port. This is valid only for downstream ports.ro
TenthdBmV
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.30
cerPortTxFlowControlModeThe transmit flow control settings for this port (network ports only).rw
FlowControlMode (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.31
cerPortRxFlowControlModeThe receive flow control settings for this port (network ports only).rw
FlowControlMode (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.32
cerPortTxFlowControlDetectedThe recerPorted transmit flow control settings for this port (network ports only).ro
FlowControlMode (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.33
cerPortRxFlowControlDetectedThe recerPorted receive flow control settings for this port (network ports only).ro
FlowControlMode (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.34
cerPortMacIfIndexThe MAC IfIndex currently associcated with the upstream or downstream port.ro
InterfaceIndexOrZero (IF-MIB)
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.35
cerPortGroupIdThe unique id of port group associated with this port.ro
PortId (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.36
cerPortGroupPortIdThe unique id of this port in the port group.ro
PortId (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.13.1.37
cerDiskVolumeTableA table of disk volume information.
SEQUENCE OF CerDiskVolumeEntry
.1.3.6.1.4.1.4998.1.1.10.1.4.14
cerDiskVolumeEntryA conceptual row containing pertinent information about a disk volume
CerDiskVolumeEntry
.1.3.6.1.4.1.4998.1.1.10.1.4.14.1
cerDiskVolumeCardIdThe unique id of the card this disk volume belongs to.
CardId (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.14.1.2
cerDiskVolumeDriveIdThe unique id of the disk drive this disk volume belongs to. A value of 99 indicates an invalid disk drive
Integer32
.1.3.6.1.4.1.4998.1.1.10.1.4.14.1.3
cerDiskVolumeIdThe unique id of this disk volume. the cerDiskVolumeCardId, the diskVolumeDiskId, and the. A value of 99 indicate an invalid volume
Integer32
.1.3.6.1.4.1.4998.1.1.10.1.4.14.1.4
cerDiskVolumeNameThe name of the disk volume.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.14.1.5
cerDiskVolumeSizeThe disk volume size in units of 2048 bytes.ro
Integer32 UNITS "bytes"
.1.3.6.1.4.1.4998.1.1.10.1.4.14.1.6
cerDiskVolumeUsageLevelThe disk volume usage level.ro
DiskVolumeUsageLevel (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.14.1.7
cerDiskVolumeUsagePercentageThe disk volume usage percentage.ro
Integer32
.1.3.6.1.4.1.4998.1.1.10.1.4.14.1.8
cerDiskVolumeUsageCriticalThresholdUsage percentage level when exceed will cause a cerDiskVolumeUsageNotification trap to be sent with cerDiskVolumeUsageLevel of diskVolumeUsageCritical.rw
Integer32
.1.3.6.1.4.1.4998.1.1.10.1.4.14.1.9
cerDiskVolumeUsageMajorThresholdUsage percentage level when exceed will cause a cerDiskVolumeUsageNotification trap to be sent with cerDiskVolumeUsageLevel of diskVolumeUsageMajor.rw
Integer32
.1.3.6.1.4.1.4998.1.1.10.1.4.14.1.10
cerDiskVolumeUsageMinorThresholdUsage percentage level when exceed will cause a cerDiskVolumeUsageNotification trap to be sent with cerDiskVolumeUsageLevel of diskVolumeUsageMinor.rw
Integer32
.1.3.6.1.4.1.4998.1.1.10.1.4.14.1.11
cerDiskVolumeAutoDeleteUnusedFileWhen set to TRUE to the system will automatically delete unused files when cerDiskVolumeUsage exceed the cerDiskVolumeUsageCriticalThreshold value.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.14.1.12
cerDiskVolumeTrapInhIf a bit is set, the corresponding trap will not be sent.rw
Bits
.1.3.6.1.4.1.4998.1.1.10.1.4.14.1.13
cerDiskVolumeDiskSizeTotal physical disk capacity in bytes.ro
Integer32 UNITS "bytes"
.1.3.6.1.4.1.4998.1.1.10.1.4.14.1.14
cerDiskVolumeFileNameThe name of a file on the disk volume use for trap notification.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.15
cerCardDataTableThis table shows the contains version information for the modules installed.
SEQUENCE OF CardDataEntry
.1.3.6.1.4.1.4998.1.1.10.1.4.16
cerCardDataEntryA conceptual row containing pertinent information about a card or a circuit pack.
CardDataEntry
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1
cerCardDataSerialNumThis is the serial number of the card.ro
SnmpAdminString
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.1
cerCardDataFwVersionThis is the firmware or FPGA version number of the card.ro
SnmpAdminString
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.2
cerCardDataHwVersionThis is the hardware version of the card.ro
SnmpAdminString
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.3
cerCardDataHwDeviationsThis is the set of hardware deviations for the card.ro
SnmpAdminString
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.4
cerCardDataSwVersionThis is the software version of the card.ro
SnmpAdminString
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.5
cerCardDataCpuTypeThe current CPU type of the card.ro
SnmpAdminString
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.6
cerCardDataCpuSpeedThe current CPU speed of the card.ro
Unsigned32 UNITS "MHz"
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.7
cerCardDataBusSpeedThe current bus speed of the card.ro
Unsigned32 UNITS "hertz"
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.8
cerCardDataRamSizeThe current size of installed RAM of the card.ro
Unsigned32 UNITS "megabytes"
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.9
cerCardDataNorFlashSizeThe current size of installed FLASH of the card.ro
Unsigned32 UNITS "bytes"
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.10
cerCardDataNandFlashSizeThe current size of installed FLASH of the card.ro
Unsigned32 UNITS "bytes"
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.11
cerCardDataFpgaSourceThe source of the running version of the FPGAs on the card.ro
FirmwareSource (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.12
cerCardDataBootVersionThe current versions of the boot loaders installed on the card.ro
SnmpAdminString
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.13
cerCardDataLastBootVersionThe last version of the boot loader used on the card.ro
SnmpAdminString
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.14
cerCardDataLastBootSourceThe source of the version of the bootloader last used on the card.ro
FirmwareSource (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.15
cerCardDataPicSerialNumThis is the serial number of the PIC.ro
SnmpAdminString
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.16
cerCardDataPicHwVersionThis is the hardware version of the PIC.ro
SnmpAdminString
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.17
cerCardDataPicHwDeviationsThis is the set of hardware deviations for the PIC.ro
SnmpAdminString
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.18
cerCardDataPicModelNumThis is the model number of the PIC.ro
SnmpAdminString
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.19
cerCardDataMfgDateTimeDate of the module's manufacture (FRU).ro
DateAndTime (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.20
cerCardDataMfgName of the manufacturer (FRU).ro
SnmpAdminString
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.21
cerCardDataProductNameName of the product (FRU).ro
SnmpAdminString
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.22
cerCardDataPartModelNumName of the model of this product (FRU).ro
SnmpAdminString
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.23
cerCardDataProductVersionVersion of the model of this product (FRU).ro
SnmpAdminString
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.24
cerCardDataAssetTagAsset tag of this part (FRU).ro
SnmpAdminString
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.25
cerCardDataCommittedSwVersionThis is the software version of the card.ro
SnmpAdminString
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.26
cerCardDataFeedAPresentThis object indicates whether power feed A is present or not.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.27
cerCardDataFeedBPresentThis object indicates whether power feed B is present or not.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.28
cerCardDataAllowedPortsThis object indicates the allowed number of licensed ports.ro
Unsigned32
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.29
cerCardDataLicenseAnnexThis object shows the annex associated with the license.ro
Enumeration
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.30
cerCardDataLicensePortsThis object indicates the number of ports associated with the license.ro
Unsigned32
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.31
cerCardDataLicenseDateThis object indicates the date associated with the license.ro
DateAndTime (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.32
cerCardDataPatchVersionsThis is the patch version(s) running on the card.ro
SnmpAdminString
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.33
cerCardDataPicModelNameThis is the model name of the PIC.ro
SnmpAdminString
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.34
cerCardDataPicMfgRevisionThis is the manufacture revision of the PIC.ro
SnmpAdminString
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.35
cerCardDataPicMfgThis is the manufacturer of the PIC.ro
SnmpAdminString
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.36
cerCardDataPicMfgDateTimeThis object indicates the date associated with the PIC.ro
DateAndTime (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.16.1.37
cerFanStatusTableStatus information for the E6 fans.
SEQUENCE OF CerFanStatusEntry
.1.3.6.1.4.1.4998.1.1.10.1.4.17
cerFanStatusEntryA conceptual row containing information about one of the fans.
CerFanStatusEntry
.1.3.6.1.4.1.4998.1.1.10.1.4.17.1
cerFan1SpeedThe last measured speed of fan1.ro
Integer32
.1.3.6.1.4.1.4998.1.1.10.1.4.17.1.1
cerFan2SpeedThe last measured speed of fan2.ro
Integer32
.1.3.6.1.4.1.4998.1.1.10.1.4.17.1.2
cerFan3SpeedThe last measured speed of fan3.ro
Integer32
.1.3.6.1.4.1.4998.1.1.10.1.4.17.1.3
cerFanLevelThe last measured speed level of fans.ro
Integer32
.1.3.6.1.4.1.4998.1.1.10.1.4.17.1.4
cerFanAmbientTemperatureThe last measured ambient temperature of fans.ro
Integer32 UNITS "degrees C"
.1.3.6.1.4.1.4998.1.1.10.1.4.17.1.5
cerPemStatusTablePEM Status information for the E6 power modules.
SEQUENCE OF CerPemStatusEntry
.1.3.6.1.4.1.4998.1.1.10.1.4.18
cerPemStatusEntryA conceptual row containing information about one of the power modules.
CerPemStatusEntry
.1.3.6.1.4.1.4998.1.1.10.1.4.18.1
cerPemLedStatusLED status of the PEMro
Enumeration
.1.3.6.1.4.1.4998.1.1.10.1.4.18.1.1
cerPemFeed1VoltageFeed 1 voltagero
Integer32 UNITS "decivolt"
.1.3.6.1.4.1.4998.1.1.10.1.4.18.1.2
cerPemFeed1CurrentFeed 1 currentro
Integer32 UNITS "deciiamp"
.1.3.6.1.4.1.4998.1.1.10.1.4.18.1.3
cerPemFeed2VoltageFeed 2 voltagero
Integer32 UNITS "decivolt"
.1.3.6.1.4.1.4998.1.1.10.1.4.18.1.4
cerPemFeed2CurrentFeed 2 currentro
Integer32 UNITS "deciamp"
.1.3.6.1.4.1.4998.1.1.10.1.4.18.1.5
cerPemFeed1PresentFeed 1 presencero
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.18.1.6
cerPemFeed2PresentFeed 2 presencero
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.18.1.7
cerPemCircuitBreaker1Enablecircuit breaker 1 presencero
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.18.1.8
cerPemCircuitBreaker2Enablecircuit breaker 2 presencero
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.4.18.1.9
cerPemBranchPresentbrach A through I presencero
Bits
.1.3.6.1.4.1.4998.1.1.10.1.4.18.1.10
equipmentDiag
OBJECT IDENTIFIER
.1.3.6.1.4.1.4998.1.1.10.1.5
eqDiagConfig
OBJECT IDENTIFIER
.1.3.6.1.4.1.4998.1.1.10.1.5.1
remainInDiagModeWhen set to TRUE, the device being diagnosed will remain in diagnostic state when the diagnostic test is completed. When set to FALSE, the device will revert to its original state when the diagnostic test is completed.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.5.1.1
consoleOutputIf true then the diagnostic result will be displayed on the system console.obsolete
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.5.1.2
verboseLevelVerbose output level for diagnostic console output display. Higher number indicate more detailed output.rw
Integer32
.1.3.6.1.4.1.4998.1.1.10.1.5.1.3
diagTestIdTest Identification Number. Used in cardTestResultNotification variable-bindingro
TestId
.1.3.6.1.4.1.4998.1.1.10.1.5.2
cardTestTableA table of test available for a card.
SEQUENCE OF CardTestEntry
.1.3.6.1.4.1.4998.1.1.10.1.5.3
cardTestEntryA conceptual row containing information about tests or dignostics available for a card.
CardTestEntry
.1.3.6.1.4.1.4998.1.1.10.1.5.3.1
cardTestIndexCard Identification Number taken from the CardTable. Used as index.
CardId (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.5.3.1.2
cardTestIdTest Identification Number. Used as index to test table
TestId
.1.3.6.1.4.1.4998.1.1.10.1.5.3.1.3
cardTestNameA unique name for this test.ro
DisplayString
.1.3.6.1.4.1.4998.1.1.10.1.5.3.1.4
cardTestTypeTest Type.ro
TestType
.1.3.6.1.4.1.4998.1.1.10.1.5.3.1.5
cardTestDescriptionA short description of the test.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.5.3.1.6
cardTestCommandCommand to be execute this test on this shelfrw
TestCommand
.1.3.6.1.4.1.4998.1.1.10.1.5.3.1.7
cardTestScheduleCommandSchedule Command to be execute this test on this shelfrw
TestScheduleCommand
.1.3.6.1.4.1.4998.1.1.10.1.5.3.1.8
cardTestScheduleTest Scheduling.rw
TestSchedule
.1.3.6.1.4.1.4998.1.1.10.1.5.3.1.9
cardTestTimeTest start time.rw
DateAndTime (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.5.3.1.10
cardTestResultResult of the test.ro
TestResult
.1.3.6.1.4.1.4998.1.1.10.1.5.3.1.11
cardTestResultDescAdditional information of the test result.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.5.3.1.12
cardTestTransIdTest transaction Id.rw
TestTransactionId
.1.3.6.1.4.1.4998.1.1.10.1.5.3.1.13
equipmentAudit
OBJECT IDENTIFIER
.1.3.6.1.4.1.4998.1.1.10.1.6
auditAutoSchedulingEnable or disable automatic audit execution.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.6.1
auditLogOutputEnable or disable logging of error entries to system log.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.6.2
auditLogThrottleEnable or disable audit log output throttling to prevent audit errors from flooding the log.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.6.3
auditTableA table of test available for a card.
SEQUENCE OF AuditEntry
.1.3.6.1.4.1.4998.1.1.10.1.6.4
auditEntryA conceptual row contains information about Audits.
AuditEntry
.1.3.6.1.4.1.4998.1.1.10.1.6.4.1
auditCardIdCard Identification Number taken from the CardTable. Used as index.
CardId (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.6.4.1.2
auditIdUnique ID of the internal Audit
Unsigned32
.1.3.6.1.4.1.4998.1.1.10.1.6.4.1.3
auditNameName of the internal Auditro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.6.4.1.4
auditDescriptionDescription of the Auditro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.6.4.1.5
auditTimeStart time of the audit.ro
DateAndTime (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.6.4.1.6
auditCommandAudit Commands. The runnow command will stop the currently running audit sequence and start executing requested audit immediated. If enabled, automatic audit schedule will be restarted.rw
Enumeration
.1.3.6.1.4.1.4998.1.1.10.1.6.4.1.7
auditStatusAudit status.ro
Enumeration
.1.3.6.1.4.1.4998.1.1.10.1.6.4.1.8
auditResultAudit Result.ro
Enumeration
.1.3.6.1.4.1.4998.1.1.10.1.6.4.1.9
auditPassedCountNumber of passed entry during previous audit run.ro
Unsigned32
.1.3.6.1.4.1.4998.1.1.10.1.6.4.1.10
auditFailedCountNumber of failed entry during previous audit run.ro
Unsigned32
.1.3.6.1.4.1.4998.1.1.10.1.6.4.1.11
auditCycleCountNumber of audit run completed.ro
Unsigned32
.1.3.6.1.4.1.4998.1.1.10.1.6.4.1.12
auditTotalPassedCountNumber of cumulative passed entry of all audit runs.ro
Unsigned32
.1.3.6.1.4.1.4998.1.1.10.1.6.4.1.13
auditTotalFailedCountNumber of cumulative failed entry of all audit runs.ro
Unsigned32
.1.3.6.1.4.1.4998.1.1.10.1.6.4.1.14
cmDevice
OBJECT IDENTIFIER
.1.3.6.1.4.1.4998.1.1.10.1.8
cmMacAddressThe MAC address for the cable modemro
MacAddress (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.8.1
cmVendorThe vendor name of the cable modemro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.8.2
cmResetReasonThe reason for the cable modem to resetro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.8.3
cmUChannelIDThe CMTS upstream channel ID which is connected to the cable modemro
Integer32
.1.3.6.1.4.1.4998.1.1.10.1.8.4
cmPrimarySIDThe primary Service Identifier (SID) assigned by the CMTS associated with the cable modemro
Unsigned32
.1.3.6.1.4.1.4998.1.1.10.1.8.5
cmResetStatusThe cable modem status before it resetsro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.8.6
cmResetUpTimeThis value indicates how long in hundreds of seconds the cable modem is up since it is initial rangedro
TimeTicks (SNMPv2-SMI)
.1.3.6.1.4.1.4998.1.1.10.1.8.7
cmResetInfoThe additional information for the cable modem to resetro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.8.8
cmIpAddressThe IP Address of the cable modemro
OCTET STRING
.1.3.6.1.4.1.4998.1.1.10.1.8.9
equipmentError
OBJECT IDENTIFIER
.1.3.6.1.4.1.4998.1.1.10.1.9
fpgaErrorEventTableOverrides default handling of FPGA error events.
SEQUENCE OF FpgaErrorEventEntry
.1.3.6.1.4.1.4998.1.1.10.1.9.1
fpgaErrorEventEntryA conceptual row containing information about FPGA error event handling.
FpgaErrorEventEntry
.1.3.6.1.4.1.4998.1.1.10.1.9.1.1
errEventIdEvent ID associated with the FPGA error. A row in this table defines behavior for a specific FPGA error that overrides the default behavior of the system.
Unsigned32
.1.3.6.1.4.1.4998.1.1.10.1.9.1.1.1
errEvRecoveryEnabledIf true, the card can be recovered when this FPGA error is detected. When the card is recovered depends on the setting of errEvRecoveryThreshold. If this value is false, the card will not be recovered when this error is detected.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.9.1.1.2
errEvLoggingEnabledIf true, the card will provide notification of the occurance of the this error. When the notification occurs is dependent on the setting of errEvLogThrottleThreshold. The severity of the notification is determined by the setting of errEvLogLevel.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.9.1.1.3
errEvLogLevelIf errEvLoggingEnabled is true, this setting sets the severity level of the generated notification. In general, higher values indicate lower severity.rw
Integer32
.1.3.6.1.4.1.4998.1.1.10.1.9.1.1.4
errEvRowStatusThe only set actions supported on this table are createAndGo(4) and destroy(6).rw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.9.1.1.5
errEvCardIdThe unique id of this card within the shelf.
CardId (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.9.1.1.6
cadEquipmentMibConformance
OBJECT IDENTIFIER
.1.3.6.1.4.1.4998.1.1.10.1.10
cadEquipmentMibCompliances
OBJECT IDENTIFIER
.1.3.6.1.4.1.4998.1.1.10.1.10.1
cadEquipmentMibGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.4998.1.1.10.1.10.2
cerSpareModeExt
OBJECT IDENTIFIER
.1.3.6.1.4.1.4998.1.1.10.1.11
cerSpareModeExtTableAllows overriding the configured sparing mode for a spare group based on the fault type that caused the sparing event.
SEQUENCE OF CerSpareModeExtEntry
.1.3.6.1.4.1.4998.1.1.10.1.11.1
cerSpareModeExtEntryA conceptual row containing information about sparing overrides for a spare group.
CerSpareModeExtEntry
.1.3.6.1.4.1.4998.1.1.10.1.11.1.1
cerSpareModeCardIdThe cardId of the spare group leader for this override.
CardId (CADANT-TC)
.1.3.6.1.4.1.4998.1.1.10.1.11.1.1.1
cerSpareModeFaultIdThe fault group associated with the override behavior. When an event occurs that would normally trigger a card reset and a sparing event and that event is in the configured fault group, the mode configured in the cerCard table is overriden. pingFault - Communications failure with active controller initTimeout - Timeout during card initialization ersmFault - Card ERSM failure swException - Software exception failure bcm3142Err - Upstream CAM PHY device fatal fault condition dulFailure - Upstream CAM periodic packet loop detected uncorrectable fault dataplaneFailrue - Fatal errors originating in dataplane processor dsUnderPower - Downstream CAM detected power on a connector is below operational threshold dsOverPower - Downstream CAM detected power on a connector is above operational threshold sbecOverflow - Excessive number of single bit ECC errors deviceFatal - General device fatal error. For example in internal datapaths or pci controller. fpgaFatalError - Fatal CRC errors detected in FPGA device clockLost - Loss of clock or loss of clock lock pwrSensorHighFault - Detected voltage is above operational threshold pwrSensorLowFault - Detected voltage is below operational threshold fpgaBufferPoolFault - Number of available buffers in MAC fpga is below threshold dataplaneLinkFault - Card has lost dataplane connectivity monitoredTaskFailure - Monitored software task has failed
Enumeration
.1.3.6.1.4.1.4998.1.1.10.1.11.1.1.2
cerSpareModeModeThe sparing mode that should be enforced when an error in the configured catagory occurs that results in a sparing event.rw
Enumeration
.1.3.6.1.4.1.4998.1.1.10.1.11.1.1.3
cerSpareModeRowStatusThe only set actions supported on this table are createAndGo(4) and destroy(6).rw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.4998.1.1.10.1.11.1.1.4
licenseError
OBJECT IDENTIFIER
.1.3.6.1.4.1.4998.1.1.10.1.12
cerLicenseTypeStrThe license type that caused the notification.ro
DisplayString
.1.3.6.1.4.1.4998.1.1.10.1.12.1
CADANT-CMTS-EQUIPMENT-MIB - SNMP MIB Reference | MIBs Explorer