AT-FIBER-MONITORING-MIB
The AT-FIBER-MONITORING-MIB enables SNMP-based monitoring of optical fiber link parameters, including signal attenuation, optical power levels, and link status, on Alcatel-Lucent (now Nokia) AT (Access Transport) hardware platforms. It facilitates the collection of physical layer performance metrics and the generation of alarms for fiber degradation or failure events to ensure transport network reliability.
Imported Objects
Objects
24 total| Object Name |
|---|
atFiberMonThis MIB contains managed objects definition and notification definitions for AT Fiber Monitoring feature. MODULE-IDENTITY .1.3.6.1.4.1.207.8.4.4.3.27 |
atFiberMonNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.4.4.3.27.0 |
atFiberMonAlarmSetNotifyA notification generated when the monitored received optical power of an SFP goes outside its alarm threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.207.8.4.4.3.27.0.1 |
atFiberMonAlarmClearedNotifyA notification generated when the monitored received optical power of an SFP returns to an acceptable value. This can occur because the power has returned to its previous level or the comparison baseline has adjusted to the new level. NOTIFICATION-TYPE .1.3.6.1.4.1.207.8.4.4.3.27.0.2 |
atFiberMonTrapVariable OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.4.4.3.27.1 |
atFiberMonReadingThe current received optical power reading for the port specified in the trap (x0.0001mW)ro Integer32 .1.3.6.1.4.1.207.8.4.4.3.27.1.1 |
atFiberMonConfigTableIt contains the objects used to configure the operation of fiber monitoring. SEQUENCE OF AtFiberMonConfigEntry .1.3.6.1.4.1.207.8.4.4.3.27.2 |
atFiberMonConfigEntryEntry for the table. It contains the configurables of fiber monitering for an interface. AtFiberMonConfigEntry .1.3.6.1.4.1.207.8.4.4.3.27.2.1 |
atFiberMonIfnameThe name of the interface where the pluggable is in.rw OCTET STRING .1.3.6.1.4.1.207.8.4.4.3.27.2.1.1 |
atFiberMonEnableEnable or disable fiber monitoring.rw Enumeration .1.3.6.1.4.1.207.8.4.4.3.27.2.1.2 |
atFiberMonIntervalFiber monitoring polling interval in seconds.rw Integer32 .1.3.6.1.4.1.207.8.4.4.3.27.2.1.3 |
atFiberMonSensitivityThe sensitivity for fiber monitoring. Acceptable mode strings and value ranges are as below: low - 2dB medium - 1dB high - 0.5dB highest - 0.0025mW fixed <25 - 65535> - units of 0.0001mW relative <0.00 - 10.00> - units of dB For example, if you want to set the sensitivity to medium level, then you enter word medium Or if you want to set it to a fixed value, then you enter string fixed 1000 Or if you want to set to a relative value, then you enter string relative 1.20rw OCTET STRING .1.3.6.1.4.1.207.8.4.4.3.27.2.1.4 |
atFiberMonBaselineThe baseline value for firber mornitoring. Acceptable mode string and value ranges are as below: average <12-150> - number of readings used to calculate moving average. fixed <1-65535> - fixed baseline value in units of 0.0001mW. For example, if you want to use a moving average of 12 readings as the baseline, you enter average 12 Or if you want to use a fixed value, though it is not recommended, you enter fixed 500rw OCTET STRING .1.3.6.1.4.1.207.8.4.4.3.27.2.1.5 |
atFiberMonAlarmActionActions to take when an alarm occurs. Acceptable values are: 1. Log a message only. 2. Send snmp trap and log. 3. Shut down the interface and log. 4. Send trap, shutdown and log.rw Enumeration .1.3.6.1.4.1.207.8.4.4.3.27.2.1.6 |
atFiberMonStateTableThis table contains the information of fiber monitoring state for SFPs. SEQUENCE OF AtFiberMonStateEntry .1.3.6.1.4.1.207.8.4.4.3.27.3 |
atFiberMonStateEntryEntry for fiber monitoring state table. It contains state values for a fiber channel. AtFiberMonStateEntry .1.3.6.1.4.1.207.8.4.4.3.27.3.1 |
atFiberMonIfindexThe index of the interface where the pluggable is in.ro Integer32 .1.3.6.1.4.1.207.8.4.4.3.27.3.1.1 |
atFiberMonChannelThe channel number of the pluggable.ro INTEGER .1.3.6.1.4.1.207.8.4.4.3.27.3.1.2 |
atFiberMonlIfDescriptionInterface description. Normally it would be the name of the interface.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.207.8.4.4.3.27.3.1.3 |
atFiberMonActualBaselineThe calculated baseline value for the link, in units of 0.0001mW.ro Integer32 .1.3.6.1.4.1.207.8.4.4.3.27.3.1.4 |
atFiberMonThresholdThreshold value for alarm to occur, in units of 0.0001mW.ro Integer32 .1.3.6.1.4.1.207.8.4.4.3.27.3.1.5 |
atFiberMonReadingHistoryThe reading history. It is a string containing last 12 readings.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.207.8.4.4.3.27.3.1.6 |
atFiberMonMinReadingThe minimum reading of rx power, in units of 0.0001mW.ro Integer32 .1.3.6.1.4.1.207.8.4.4.3.27.3.1.7 |
atFiberMonMaxReadingThe maximum reading of rx power, in units of 0.0001mW.ro Integer32 .1.3.6.1.4.1.207.8.4.4.3.27.3.1.8 |
More MIBs from Allied Telesis
Browse all Allied TelesisMIBs →The AT-UWC-WLAN-SWITCH-MIB provides vendor-specific SNMP management for Allied Telesis Universal Wireless Controller (UWC) hardware, enabling monitoring of WLAN switch operational states, interface statistics, and wireless client association metrics.
The AtiEdgeSwitch-MIB provides vendor-specific SNMP extensions for monitoring and managing Layer 2 stackable switch operations, including interface status, port statistics, and stack topology, on ATI hardware platforms within Windows and UNIX network management environments.
Standard SNMP MIB module defining data structures for ALLIEDTELESYN-MIB.
The AT-BOARDS-MIB module provides a structured OID hierarchy for monitoring and managing specific hardware components on Allied Telesis devices, including board identifiers, firmware release versions, interface type definitions, and integrated chip IDs. This MIB enables granular inventory tracking and hardware status verification by mapping logical identifiers to physical subsystems within the network equipment chassis.
SWITCH-ATM-MIB monitors and manages Asynchronous Transfer Mode (ATM) interfaces and virtual circuit states on network switches, specifically tracking VPI/VCI pairings and traffic counters under the constraint that the Virtual Path Identifier is fixed by the implementation and excluded from table indexing.
Standard SNMP MIB module defining data structures for AtiL2-MIB.