AT-SYSINFO-MIB
AI MIB Summary
The AT-SYSINFO-MIB provides a vendor-specific subtree for monitoring Atheros/AR934x-based hardware system health, exposing metrics for fan and power supply status, CPU utilization, system temperature, and environmental monitoring data. It also facilitates the retrieval of host identification, non-volatile storage details, and port information to support device management and fault isolation on embedded networking platforms.
Subtree beneath which system inforamtion ids are assigned. It contains generic system information, as follows: { sysinfo 1 } fanAndPs { sysinfo 2 } restartGroup { sysinfo 3 } cpu { sysinfo 4 } sysTemperature { sysinfo 5 } atrContactDetails { sysinfo 6 } bbrNvs { sysinfo 9 } hostId { sysinfo 10 } envMon { sysinfo 11 } xem { sysinfo 12 } awpEnvMon { sysinfo 13 } awpStack { sysinfo 14 } atPortInfo
Main OID:
sysinfo.1.3.6.1.4.1.207.8.4.4.3
98
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
98 total| Object Name |
|---|
sysinfoSubtree beneath which system inforamtion ids are assigned. It contains generic system information, as follows: { sysinfo 1 } fanAndPs { sysinfo 2 } restartGroup { sysinfo 3 } cpu { sysinfo 4 } sysTemperature { sysinfo 5 } atrContactDetails { sysinfo 6 } bbrNvs { sysinfo 9 } hostId { sysinfo 10 } envMon { sysinfo 11 } xem { sysinfo 12 } awpEnvMon { sysinfo 13 } awpStack { sysinfo 14 } atPortInfo MODULE-IDENTITY .1.3.6.1.4.1.207.8.4.4.3 |
fanAndPs OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.4.4.3.1 |
fanAndPsTrap OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.4.4.3.1.0 |
fanAndPsRpsConnectionTrapGenerated when the RPS connection status changes. NOTIFICATION-TYPE .1.3.6.1.4.1.207.8.4.4.3.1.0.1 |
fanAndPsMainPSUStatusTrapGenerated when the main power supply status changes. NOTIFICATION-TYPE .1.3.6.1.4.1.207.8.4.4.3.1.0.2 |
fanAndPsRedundantPSUStatusTrapGenerated when the RPS status changes. NOTIFICATION-TYPE .1.3.6.1.4.1.207.8.4.4.3.1.0.3 |
fanAndPsMainFanStatusTrapGenerated when the main fan changes status. NOTIFICATION-TYPE .1.3.6.1.4.1.207.8.4.4.3.1.0.4 |
fanAndPsRedundantFanStatusTrapGenerated when the redundant fan changes status. NOTIFICATION-TYPE .1.3.6.1.4.1.207.8.4.4.3.1.0.5 |
fanAndPsTemperatureStatusTrapGenerated when the temperature changes status. NOTIFICATION-TYPE .1.3.6.1.4.1.207.8.4.4.3.1.0.6 |
fanAndPsFanTrayPresentTrapGenerated when the fan tray presence status changes. NOTIFICATION-TYPE .1.3.6.1.4.1.207.8.4.4.3.1.0.7 |
fanAndPsFanTrayStatusTrapGenerated when the fan tray status changes. NOTIFICATION-TYPE .1.3.6.1.4.1.207.8.4.4.3.1.0.8 |
fanAndPsMainMonitoringStatusTrapGenerated when the main power supply monitoring status changes. NOTIFICATION-TYPE .1.3.6.1.4.1.207.8.4.4.3.1.0.9 |
fanAndPsAccelFanStatusTrapGenerated when the accelerator fans' status changes. NOTIFICATION-TYPE .1.3.6.1.4.1.207.8.4.4.3.1.0.10 |
fanAndPsRpsConnectionStatusThe status of the Redundant Power Supply (RPS) connection, ie, whether an RPS is actually connected or not, regardless of whether the RPS is on or not. notSupported means that an RPS is not supported in this hardware platform, connected means that the RPS is connected, notConnected means that the RPS is not connected, and notMonitoring means that the status of the RPS is not being monitored presently. RPS monitoring can be turned on via the variable fanAndPsRpsMonitoringStatus, or by the command SET SYSTEM RPSMONITOR=ON.ro Enumeration .1.3.6.1.4.1.207.8.4.4.3.1.1 |
fanAndPsMainPSUStatusThe status of the main Power Supply. on means that the power supply is present and fully operational. off means that the power supply is totally off (and obviously only applies to systems with a redundant power supply). faulty means that the main power supply is delivering power but that a component of the power supply is faulty. This applies to systems like SwitchBlade which have 3 power supplies but do not provide individual power supply monitoring. Also, in the case of SwitchBlade, power supply status includes the status of the fans in the power supply.ro Enumeration .1.3.6.1.4.1.207.8.4.4.3.1.2 |
fanAndPsRedundantPSUStatusThe status of the redundant Power Supply. notSupported means this device does not support redundant power supplies, on means that the redundant power supply is connected and able to supply system power if required, off means that the redundant power supply is either not connected or is connected and is not able to supply system power if required, and notMonitoring means that the status of the RPS is not being monitored presently. RPS monitoring can be turned on via the variable fanAndPsRpsMonitoringStatus, or by the command SET SYSTEM RPSMONITOR=ON.ro Enumeration .1.3.6.1.4.1.207.8.4.4.3.1.3 |
fanAndPsRpsMonitoringStatusThe current status of redundant power supply monitoring. The monitoring of the redundant power supply and its fan must be enabled by command or by setting this variable to on. The value notSupported means that this device does not support redundant power supplies. Only the values on or off may be written to this variable. If this variables reads as notSupported, an attempt to write to this variable will result in a bad value error.rw Enumeration .1.3.6.1.4.1.207.8.4.4.3.1.4 |
fanAndPsMainFanStatusThe status of the main Power Supply fan. notSupported means that this device does not support monitoring on the main power supply fan, or that there is no main power supply fan. The warning means the fan's speed is outside 30% of the expected speed.ro Enumeration .1.3.6.1.4.1.207.8.4.4.3.1.5 |
fanAndPsRedundantFanStatusThe status of the redundant Power Supply Fan. notSupported means this device does not support redundant power supplies, ok means that the redundant power supply fan is running, notOk means that the redundant power supply fan is not running, and notMonitoring means that the status of the RPS is not being monitored presently. RPS monitoring can be turned on via the variable fanAndPsRpsMonitoringStatus, or by the command SET SYSTEM RPSMONITOR=ON.ro Enumeration .1.3.6.1.4.1.207.8.4.4.3.1.6 |
fanAndPsTemperatureStatusThe status of temperature in this device. ok means that the device is not capable of monitoring temperature or that the temperature is OK, notOk means that the temperature is being monitored and is currently out of the range 0C - 45C.ro Enumeration .1.3.6.1.4.1.207.8.4.4.3.1.7 |
fanAndPsFanTrayPresentThe status of the presence of the fan tray in this system. Systems which do not support a fan tray return the value notSupported. Upon removal of the fan tray there is a short period (20s) before the value of this variable is changed to notPresent. This is to allow for scheduled replacement and/or cleaning of the fan tray.ro Enumeration .1.3.6.1.4.1.207.8.4.4.3.1.8 |
fanAndPsFanTrayStatusThe status of the fan tray in this system. Systems which do not support a fan tray return the value notSupported. The value ok is returned if all fans in the fan tray are running at full speed. The value notOk is returned if one of more of the fan tray fans is running slow or has stalled.ro Enumeration .1.3.6.1.4.1.207.8.4.4.3.1.9 |
fanAndPsMainMonitoringStatusThe current status of main power supply monitoring. The monitoring of the main power supply and its fan is always enabled by those systems that support it. Systems which do not support main power supply or fan monitoring report a value of notSupported. The value ok is returned for those systems that do support main power supply and fan monitoring, and where the monitoring operation is reporting valid information (refer to fanAndPsMainFanStatus for the current status of the system). When main power supply and fan monitoring is failing, the value notOk is returned.ro Enumeration .1.3.6.1.4.1.207.8.4.4.3.1.10 |
fanAndPsPsuStatusTableThe table of AT8948 fanAndPsPsuStatusTable. Each entry in the table represents the status of one of the power supplies in AT8948 system. Each power supply has its own board ID. SEQUENCE OF FanAndPsPsuStatusEntry .1.3.6.1.4.1.207.8.4.4.3.1.11 |
fanAndPsPsuStatusEntryA single entry of AT8948 fanAndPsPsuStatusTable, indexed by fanAndPsPsuNumber field. FanAndPsPsuStatusEntry .1.3.6.1.4.1.207.8.4.4.3.1.11.1 |
fanAndPsPsuNumberThe PSU board identity for which this entry holds. If the system consists only of a single PSU board, only one entry will appear in the table, whose index is 1.ro INTEGER .1.3.6.1.4.1.207.8.4.4.3.1.11.1.1 |
fanAndPsPsuPresentThe PSU present state, displayed as 'yes' if present, or 'no' if absent.ro Enumeration .1.3.6.1.4.1.207.8.4.4.3.1.11.1.2 |
fanAndPsPsuTypeThe PSU type, displayed as AC, or DC, or FAN, or NOT PRESENT.ro Enumeration .1.3.6.1.4.1.207.8.4.4.3.1.11.1.3 |
fanAndPsPsuFanThe PSU fan status, displayed as OK, or FAIL, or NOT PRESENT.ro Enumeration .1.3.6.1.4.1.207.8.4.4.3.1.11.1.4 |
fanAndPsPsuTemperatureThe PSU temperature, displayed as GOOD, or HIGH, or NOT PRESENT, or NOT SUPPORTED.ro Enumeration .1.3.6.1.4.1.207.8.4.4.3.1.11.1.5 |
fanAndPsPsuPowerThe PSU power status, displayed as GOOD, or BAD, or NOT PRESENT or NOT SUPPORTED.ro Enumeration .1.3.6.1.4.1.207.8.4.4.3.1.11.1.6 |
fanAndPsAccelFanStatusThe status of the accelerator card fans. Non-supported means this device does not support monitoring of the accelerator card fans.ro Enumeration .1.3.6.1.4.1.207.8.4.4.3.1.12 |
restartGroup OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.4.4.3.2 |
restartA router/switch restart request. A management station can remotely instruct an ATI router/switch to action a warm or cold restart. Once all the appropriate internal checks have been made, the router/switch will acknowledge the request via normal SNMP channels. The restart instruction will be actioned after waiting for a period of 5 seconds, this is because the SNMP acknowledgement packet needs time to reach the management station. Once the request has been actioned, it can not be cancelled and communication with the router/switch will be lost during system initialisation.rw Enumeration .1.3.6.1.4.1.207.8.4.4.3.2.1 |
restartCauseThe reason for last time restart.ro Enumeration .1.3.6.1.4.1.207.8.4.4.3.2.2 |
restartLogThe restart logging details.ro DisplayStringUnsized .1.3.6.1.4.1.207.8.4.4.3.2.3 |
restartNotificationA restart notification is a trap sent to tell snmp managers the reason of restarting NOTIFICATION-TYPE .1.3.6.1.4.1.207.8.4.4.3.2.11 |
cpu OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.4.4.3.3 |
cpuUtilisationMaxMaximum CPU utilisation since the router was last restarted. Expressed as a percentage.ro INTEGER .1.3.6.1.4.1.207.8.4.4.3.3.1 |
cpuUtilisationAvgAverage CPU utilisation since the router was last restarted. Expressed as a percentage.ro INTEGER .1.3.6.1.4.1.207.8.4.4.3.3.2 |
cpuUtilisationAvgLastMinuteAverage CPU utilisation over the past minute. Expressed as a percentage.ro INTEGER .1.3.6.1.4.1.207.8.4.4.3.3.3 |
cpuUtilisationAvgLast10SecondsAverage CPU utilisation over the past ten seconds. Expressed as a percentage.ro INTEGER .1.3.6.1.4.1.207.8.4.4.3.3.4 |
cpuUtilisationAvgLastSecondAverage CPU utilisation over the past second. Expressed as a percentage.ro INTEGER .1.3.6.1.4.1.207.8.4.4.3.3.5 |
cpuUtilisationMaxLast5MinutesMaximum CPU utilisation over the last 5 minutes. Expressed as a percentage.ro INTEGER .1.3.6.1.4.1.207.8.4.4.3.3.6 |
cpuUtilisationAvgLast5MinutesAverage CPU utilisation over the past 5 minutes. Expressed as a percentage.ro INTEGER .1.3.6.1.4.1.207.8.4.4.3.3.7 |
cpuUtilisationStackTableA list of stack members. For a chassis switch, this is a list of cards. SEQUENCE OF CpuUtilisationStackEntry .1.3.6.1.4.1.207.8.4.4.3.3.8 |
cpuUtilisationStackEntryA set of parameters that describe the CPU utilisation of a stack member. For a chassis switch, it corresponds to the CPU utilisation of a card. CpuUtilisationStackEntry .1.3.6.1.4.1.207.8.4.4.3.3.8.1 |
cpuUtilisationStackIdStack member ID. For a chassis switch, it corresponds to the card ID.ro Unsigned32 .1.3.6.1.4.1.207.8.4.4.3.3.8.1.1 |
cpuUtilisationStackMaxMaximum CPU utilisation since the router was last restarted. Expressed as a percentage.ro INTEGER .1.3.6.1.4.1.207.8.4.4.3.3.8.1.2 |
cpuUtilisationStackAvgAverage CPU utilisation since the router was last restarted. Expressed as a percentage.ro INTEGER .1.3.6.1.4.1.207.8.4.4.3.3.8.1.3 |
cpuUtilisationStackAvgLastMinuteAverage CPU utilisation over the past minute. Expressed as a percentage.ro INTEGER .1.3.6.1.4.1.207.8.4.4.3.3.8.1.4 |
cpuUtilisationStackAvgLast10SecondsAverage CPU utilisation over the past ten seconds. Expressed as a percentage.ro INTEGER .1.3.6.1.4.1.207.8.4.4.3.3.8.1.5 |
cpuUtilisationStackAvgLastSecondAverage CPU utilisation over the past second. Expressed as a percentage.ro INTEGER .1.3.6.1.4.1.207.8.4.4.3.3.8.1.6 |
cpuUtilisationStackMaxLast5MinutesMaximum CPU utilisation over the last 5 minutes. Expressed as a percentage.ro INTEGER .1.3.6.1.4.1.207.8.4.4.3.3.8.1.7 |
cpuUtilisationStackAvgLast5MinutesAverage CPU utilisation over the past 5 minutes. Expressed as a percentage.ro INTEGER .1.3.6.1.4.1.207.8.4.4.3.3.8.1.8 |
sysTemperature OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.4.4.3.4 |
generalTemperature OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.4.4.3.4.1 |
generalTemperatureTrap OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.4.4.3.4.1.0 |
generalTemperatureStatusTrapGenerated when the temperature status of the device changes. NOTIFICATION-TYPE .1.3.6.1.4.1.207.8.4.4.3.4.1.0.1 |
generalTemperatureSupportedThe value supported indicates general temperature is displayed by the device. The value notSupported indicates the device displays specific temperature information or none at all.ro Enumeration .1.3.6.1.4.1.207.8.4.4.3.4.1.1 |
generalTemperatureActualTempThe current temperature of product's base board, in degrees Celsius. A device which doesn't support this group will return the value 0 for this variable.ro INTEGER .1.3.6.1.4.1.207.8.4.4.3.4.1.2 |
generalTemperatureStatusThe status of temperature in this device. ok indicates the temperature is below the threshold temperature or the device is not capable of monitoring temperature. notOk indicates the temperature is being monitored and is currently above the threshold temperature (displayed in generalTemperatureThreshold).ro Enumeration .1.3.6.1.4.1.207.8.4.4.3.4.1.3 |
generalTemperatureThresholdThe temperature threshold for the device. If the temperature of the device rises above this threshold generalTemeratureStatus will indicate a notOk status.rw INTEGER .1.3.6.1.4.1.207.8.4.4.3.4.1.4 |
sbTemperature OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.4.4.3.4.2 |
sbTemperatureTrap OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.4.4.3.4.2.0 |
sbTempFixedThresholdTrapTrap occurs when fixed threshold status changes. The actual temperature and the fixed threshold are also given. NOTIFICATION-TYPE .1.3.6.1.4.1.207.8.4.4.3.4.2.0.1 |
sbTempSettableThresholdTrapTrap occurs when settable threshold status changes. The actual temperature and the settable threshold are also given. NOTIFICATION-TYPE .1.3.6.1.4.1.207.8.4.4.3.4.2.0.2 |
sbTempTableThe table of SwitchBlade sysTemperature. Each entry in the table represents temperature monitoring from one of the CPU cards which may be present in the SwitchBlade system. SEQUENCE OF SbTempEntry .1.3.6.1.4.1.207.8.4.4.3.4.2.1 |
sbTempEntryA single entry of SwitchBlade sysTemperature SbTempEntry .1.3.6.1.4.1.207.8.4.4.3.4.2.1.1 |
sbTempIndexThe board for which this temperature entry holds. If the system consists only of a single CPU board, only one entry will appear in the table, whose index is master(1).ro Enumeration .1.3.6.1.4.1.207.8.4.4.3.4.2.1.1.1 |
sbTempActualTemperatureThe actual SwitchBlade temperature. This temperature is measured within the SwitchBlade CPU, and is sampled at 1 second intervals.ro INTEGER .1.3.6.1.4.1.207.8.4.4.3.4.2.1.1.2 |
sbTempFixedThresholdStatusThe temperature status with regard to the fixed temperature threshold. The value of the fixed temperature threshold is set at 90 degrees C. This variable represents whether the actual temperature is above the threshold (value is crossover(2)) or below the threshold (value is normal(1)). If the temperature is exactly the same as the fixed temperature threshold, the value of this variable reads as normal(1).ro Enumeration .1.3.6.1.4.1.207.8.4.4.3.4.2.1.1.3 |
sbTempSettableThresholdStatusThe temperature status with regard to the settable temperature threshold. The value of the settable temperature threshold is set by management intervention. This variable represents whether the actual temperature is above the threshold (value is crossover(2)) or below the threshold (value is normal(1)). When the value of this variable is undefined(3), no settable threshold has been specified and the value of sbTempSettableThreshold is not used.ro Enumeration .1.3.6.1.4.1.207.8.4.4.3.4.2.1.1.4 |
sbTempSettableThresholdThe value of the settable temperature threshold. This can be set independently for each temperature entry. The value of this threshold is only valid when sbTempSettableThresholdStatus is not set to undefined(3).rw INTEGER .1.3.6.1.4.1.207.8.4.4.3.4.2.1.1.5 |
sbTempFixedThresholdThe value of the fixed temperature threshold. This value is fixed for both CPU cards, and cannot be set.ro INTEGER .1.3.6.1.4.1.207.8.4.4.3.4.2.2 |
acceleratorTemperature OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.4.4.3.4.3 |
acceleratorTemperatureTrap OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.4.4.3.4.3.0 |
acceleratorTemperatureStatusTrapGenerated when the temperature status of the device changes. NOTIFICATION-TYPE .1.3.6.1.4.1.207.8.4.4.3.4.3.0.1 |
acceleratorTemperatureSupportedThe value supported indicates whether accelerator card temperature is displayed by the device. The value notSupported indicates the device does not display specific accelerator card temperature information.ro Enumeration .1.3.6.1.4.1.207.8.4.4.3.4.3.1 |
acceleratorTemperatureActualTempThe current temperature of product's base board, in degrees Celsius. A device which doesn't support this group will return the value 0 for this variable.ro INTEGER .1.3.6.1.4.1.207.8.4.4.3.4.3.2 |
acceleratorTemperatureStatusThe status of temperature in this device. ok indicates the temperature is below the threshold temperature or the device is not capable of monitoring temperature. notOk indicates the temperature is being monitored and is currently above the threshold temperature (displayed in generalTemperatureThreshold).ro Enumeration .1.3.6.1.4.1.207.8.4.4.3.4.3.3 |
acceleratorTemperatureThresholdThe temperature threshold for the device. If the temperature of the device rises above this threshold generalTemeratureStatus will indicate a notOk status.ro INTEGER .1.3.6.1.4.1.207.8.4.4.3.4.3.4 |
atContactDetailsThe contact details for Allied Telesis inc.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.207.8.4.4.3.5 |
bbrNvs OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.4.4.3.6 |
bbrNvsTrap OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.4.4.3.6.0 |
bbrNvsReinitialiseTrapGenerated at boot when the device detects that the BBR has been corrupted and reinitialised. This can happen if the device's BBR battery has run down, and the device has been powered off, then on. NOTIFICATION-TYPE .1.3.6.1.4.1.207.8.4.4.3.6.0.1 |
memory OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.4.4.3.7 |
freeMemoryPercentage of free memory still available on devicero INTEGER .1.3.6.1.4.1.207.8.4.4.3.7.1 |
totalBuffersTotal number of buffers available on devicero INTEGER .1.3.6.1.4.1.207.8.4.4.3.7.2 |
lowMemoryTrapA low memory trap is generated when a router's memory has gone below a certain level. NOTIFICATION-TYPE .1.3.6.1.4.1.207.8.4.4.3.7.11 |
realTimeClockStatusShows the status of the real time clockro Enumeration .1.3.6.1.4.1.207.8.4.4.3.8 |
hostIdHost Identifier of this devicerw INTEGER .1.3.6.1.4.1.207.8.4.4.3.9 |
atPortInfo OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.4.4.3.14 |
atPortInfoTransceiverTableA table of information about the transceiver of a interface. SEQUENCE OF AtPortInfoTransceiverEntry .1.3.6.1.4.1.207.8.4.4.3.14.1 |
atPortInfoTransceiverEntryThe description, the transceiver type of a interface. AtPortInfoTransceiverEntry .1.3.6.1.4.1.207.8.4.4.3.14.1.1 |
atPortInfoTransceiverifIndexThe ifIndex for the interface represented by this entry of the interfaces table.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.207.8.4.4.3.14.1.1.1 |
atPortInfoTransceiverTypeThis object indicates the type of transceiver on a interface.ro Enumeration .1.3.6.1.4.1.207.8.4.4.3.14.1.1.2 |
atPortRenumberEventsThe number of times that port number values (represented by the dot1dBasePort object in BRIDGE-MIB), have been re-assigned due to stack member leave/join events or XEM hot-swap events, since the system was initialised.ro INTEGER .1.3.6.1.4.1.207.8.4.4.3.14.2 |