ADTRAN-ACTDAXL3-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for ADTRAN-ACTDAXL3-MIB.
225
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
225 total| Object Name |
|---|
adtran OBJECT IDENTIFIER .1.3.6.1.4.1.664 |
RFC1155-SMI Unknown .1.3.6.1.4.1.664 |
adProducts OBJECT IDENTIFIER .1.3.6.1.4.1.664.1 |
adACTDAXL3 OBJECT IDENTIFIER .1.3.6.1.4.1.664.1.9 |
adACTDAXL3systemHdwFailureClearThis trap indicates that a system hardware failure
has cleared on the ACT DAX. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.906 |
adACTDAXL3systemHdwFailureThis trap indicates that a system hardware failure
has occured on the ACT DAX. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.907 |
adACTDAXL3systemSfwFailureClearThis trap indicates that a system software failure
has cleared on the ACT DAX. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.908 |
adACTDAXL3systemSfwFailureThis trap indicates that a system software failure
has occured on the ACT DAX. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.909 |
adACTDAXL3RxYellowClearThis trap indicates that a yellow alarm state has cleared
on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.910 |
adACTDAXL3RxYellowThis trap indicates that yellow alarm is being received
on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.911 |
adACTDAXL3TxYellowClearThis trap indicates that a yellow alarm signal is no
longer being transmitted on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.912 |
adACTDAXL3TxYellowThis trap indicates that a yellow alarm signal is being
transmitted on the specifed ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.913 |
adACTDAXL3RxAISclearThis trap indicates that an alarm indication signal (AIS)
state has cleared on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.914 |
adACTDAXL3RxAISThis trap indicates that an alarm indication signal (AIS)
state has occured on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.915 |
adACTDAXL3TxAISclearThis trap indicates that an alarm indication signal (AIS)
is no longer being transmitted on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.916 |
adACTDAXL3TxAISThis trap indicates that an alarm indication signal (AIS)
is being transmitted on the specifed ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.917 |
adACTDAXL3RedAlarmClearThis trap indicates that a red alarm has cleared on the
specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.918 |
adACTDAXL3RedAlarmThis trap indicates that a red alarm has occured on the
specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.919 |
adACTDAXL3LOSclearThis trap indicates that a loss of signal state has cleared
on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.920 |
adACTDAXL3LOSThis trap indicates that a loss of signal state has occured
on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.921 |
adACTDAXL3LocalLoopClearThis trap indicates that a local loopback has cleared on
the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.922 |
adACTDAXL3LocalLoopThis trap indicates that a local loopback has occured on
the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.923 |
adACTDAXL3LineLoopClearThis trap indicates that a line loopback has cleared on
the specified ds1 line. The line loopback was commanded
by the hardware switch or through an administrative port. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.924 |
adACTDAXL3LineLoopThis trap indicates that a line loopback has occured on
the specified ds1 line. The line loopback was commanded
by the hardware switch or through an administrative port. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.925 |
adACTDAXL3PayloadLoopClearThis trap indicates that a payload loopback has occured
on the specified ds1 line. The payload loopback was commanded
by the hardware switch or through an administrative port. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.926 |
adACTDAXL3PayloadLoopThis trap indicates that a payload loopback has occured
on the specified ds1 line. The payload loopback was commanded
by the hardware switch or through an administrative port. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.927 |
adACTDAXL3fdlLineLoopClearThis trap indicates that a line loopback has cleared on
the specified ds1 line. The line loopback was commanded
from the far end through the facility data link. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.928 |
adACTDAXL3fdlLineLoopThis trap indicates that a line loopback has occured on
the specified ds1 line. The line loopback was commanded
from the far end through the facility data link. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.929 |
adACTDAXL3fdlPayloadLoopClearThis trap indicates that a payload loopback has occured
on the specified ds1 line. The payload loopback was commanded
from the far end through the facility data link. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.930 |
adACTDAXL3fdlPayloadLoopThis trap indicates that a payload loopback has occured
on the specified ds1 line. The payload loopback was commanded
from the far end through the facility data link. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.931 |
adACTDAXL3farLineLoopClearThis trap indicates that the far end has cleared a line
loopback which was commanded from the near end through
the facility data link. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.932 |
adACTDAXL3farLineLoopThis trap indicates that the far end has been commanded
into a line loopback from the near end through the facility
data link. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.933 |
adACTDAXL3farPayloadLoopClearThis trap indicates that the far end has cleared a payload
loopback which was commanded from the near end through
the facility data link. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.934 |
adACTDAXL3farPayloadLoopThis trap indicates that the far end has been commanded
into a payload loopback from the near end through the facility
data link. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.935 |
adACTDAXL3bankAlarmClearThis trap indicates that a ACT 1241 bank has cleared. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.936 |
adACTDAXL3bankAlarmThis trap indicates that the ACT 1241 bank is in alarm. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.937 |
adACTDAXL3DailyESThis trap indicates that the daily (total) interval Errored
Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.960 |
adACTDAXL3DailySESThis trap indicates that the daily (total) interval Severely
Errored Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.961 |
adACTDAXL3DailySEFSThis trap indicates that the daily (total) interval Severely
Errored Framing Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.962 |
adACTDAXL3DailyUASThis trap indicates that the daily (total) interval Unavailable
Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.963 |
adACTDAXL3DailyCSSThis trap indicates that the daily (total) interval Controlled
Slip Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.964 |
adACTDAXL3DailyPCVThis trap indicates that the daily (total) interval Path Code
Violations threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.965 |
adACTDAXL3DailyLESThis trap indicates that the daily (total) interval Line Errored
Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.966 |
adACTDAXL3DailyBESThis trap indicates that the daily (total) interval Bursty Errored
Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.967 |
adACTDAXL3DailyLCVThis trap indicates that the daily (total) interval Line Code
Violations threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.969 |
adACTDAXL3CurrentESThis trap indicates that the current interval Errored
Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.970 |
adACTDAXL3CurrentSESThis trap indicates that the current interval Severely
Errored Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.971 |
adACTDAXL3CurrentSEFSThis trap indicates that the current interval Severely
Errored Framing Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.972 |
adACTDAXL3CurrentUASThis trap indicates that the current interval Unavailable
Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.973 |
adACTDAXL3CurrentCSSThis trap indicates that the current interval Controlled
Slip Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.974 |
adACTDAXL3CurrentPCVThis trap indicates that the current interval Path Code
Violations threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.975 |
adACTDAXL3CurrentLESThis trap indicates that the current interval Line Errored
Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.976 |
adACTDAXL3CurrentBESThis trap indicates that the current interval Bursty Errored
Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.977 |
adACTDAXL3CurrentLCVThis trap indicates that the current interval Line Code
Violations threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.979 |
adACTDAXL3FarDailyESThis trap indicates that the far end daily (total) interval Errored
Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.980 |
adACTDAXL3FarDailySESThis trap indicates that the far end daily (total) interval Severely
Errored Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.981 |
adACTDAXL3FarDailySEFSThis trap indicates that the far end daily (total) interval Severely
Errored Framing Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.982 |
adACTDAXL3FarDailyUASThis trap indicates that the far end daily (total) interval Unavailable
Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.983 |
adACTDAXL3FarDailyCSSThis trap indicates that the far end daily (total) interval Controlled
Slip Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.984 |
adACTDAXL3FarDailyPCVThis trap indicates that the far end daily (total) interval Path Code
Violations threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.985 |
adACTDAXL3FarDailyLESThis trap indicates that the far end daily (total) interval Line Errored
Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.986 |
adACTDAXL3FarDailyBESThis trap indicates that the far end daily (total) interval Bursty Errored
Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.987 |
adACTDAXL3FarCurrentESThis trap indicates that the far end current interval Errored
Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.990 |
adACTDAXL3FarCurrentSESThis trap indicates that the far end current interval Severely
Errored Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.991 |
adACTDAXL3FarCurrentSEFSThis trap indicates that the far end current interval Severely
Errored Framing Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.992 |
adACTDAXL3FarCurrentUASThis trap indicates that the far end current interval Unavailable
Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.993 |
adACTDAXL3FarCurrentCSSThis trap indicates that the far end current interval Controlled
Slip Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.994 |
adACTDAXL3FarCurrentPCVThis trap indicates that the far end current interval Path Code
Violations threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.995 |
adACTDAXL3FarCurrentLESThis trap indicates that the far end current interval Line Errored
Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.996 |
adACTDAXL3FarCurrentBESThis trap indicates that the far end current interval Bursty Errored
Seconds threshold has been exceeded on the specified ds1 line. TRAP-TYPE .1.3.6.1.4.1.664.1.9.0.997 |
adMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.664.2 |
adACTDAXL3mg OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.9 |
adDAX3config OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.9.2 |
adDAX3passwordThe password string used for authentication of SNMP
messages between Proxy Agent and ACTDAX. Maximum of
12 characters. The factory default is 'PASSWORD'.
This password is NOT the same as either the read-only
or read/write passwords for the EASYMENU terminal
interface.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.9.2.1 |
adDAX3deviceAddressThe device address for this ACTDAX. The device
address is used to access the device from the proxy
agent.ro INTEGER .1.3.6.1.4.1.664.2.9.2.2 |
adDAX3timeThe current ACTDAX time value. A sequence of
ASCII characters encoded as HH:MM:SS. For example,
1:15 pm is 13:15:00.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.9.2.3 |
adDAX3dateThe current ACTDAX date value. A sequence of
ASCII characters encoded as MM/DD/YY. For example,
April 28, 1994 is 04/28/94.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.9.2.4 |
adDAX3resetPMResets Performance Monitor DS1 statistic counters
in ACTDAX. Parameter value 1 resets all lines,
2 resets line 1 (DS1-A), 3 resets line 2 (DS1-B).rw Enumeration .1.3.6.1.4.1.664.2.9.2.5 |
adDAX3auditProgCodeA Get performs an audit of the units Program Code and
returns the result as PASS or FAIL.ro Enumeration .1.3.6.1.4.1.664.2.9.2.6 |
adDAX3selfTestAndRestartA Set restarts ACTDAX and performs unit self-test.
Results of last unit self-test are shown as PASS or FAIL.rw Enumeration .1.3.6.1.4.1.664.2.9.2.7 |
adDAX3resetFactoryConfigA Set resets ALL provisioning to the factory defaults.rw INTEGER .1.3.6.1.4.1.664.2.9.2.8 |
adDAX3primaryTimingThe Primary Facility Timing for the ACT 1241 and the
ACTDAX. The timing set on the ACT OIU must match the
timing set on the ACT DAX.
'localOrExternal' indicates that the ACTDAX is timed
either a local free-running oscillator or frequency
locked to an external clock signal.
'loopA' indicates that the ACTDAX is frequency locked
to the received DS1 A line signal.
'loopB' indicates that the ACTDAX is frequency locked
to the received DS1 B line signal.rw Enumeration .1.3.6.1.4.1.664.2.9.2.9 |
adDAX3backupTimingThe Backup Facility Timing for the ACT 1241 and the
ACTDAX. The backup timing is only used if the
adDAX3primaryTiming is either 'loopA' or 'loopB'.
'local' indicates that if the DS1 line fails, which is
the primary timing source, then the ACTDAX will time
to a local free-running oscillator.
'loop' indicates that if the DS1 line fails, which is
the primary timing source, then the ACTDAX will time to
the other DS1 line. If both DS1 lines fail then the
ACTDAX will time to a local free-running oscillator.rw Enumeration .1.3.6.1.4.1.664.2.9.2.10 |
adDAX3ds1AlineEqlzThe DS1 Line A transmit pre-equalizer circuitry
provisioning for conditioning the T1 output signal
for connection to a CSU, other customer premises
equipment, or the DSX-1 cross-connect through
various cable lengths between 0 and 655 feet.
'0-110' indicates 0-110 feet.
'110-220' indicates 110-220 feet.
'220-330' indicates 220-330 feet.
'330-440' indicates 330-440 feet.
'440-550' indicates 440-550 feet.
'550-655' indicates 550-655 feet.rw Enumeration .1.3.6.1.4.1.664.2.9.2.11 |
adDAX3ds1BlineEqlzThe DS1 Line B transmit pre-equalizer circuitry
provisioning for conditioning the T1 output signal
for connection to a CSU, other customer premises
equipment, or the DSX-1 cross-connect through
various cable lengths between 0 and 655 feet.
'0-110' indicates 0-110 feet.
'110-220' indicates 110-220 feet.
'220-330' indicates 220-330 feet.
'330-440' indicates 330-440 feet.
'440-550' indicates 440-550 feet.
'550-655' indicates 550-655 feet.rw Enumeration .1.3.6.1.4.1.664.2.9.2.12 |
adDAX3ds1AoperationThe DS1 Line A Operational Status.
'disabled' turns off the faceplate indicators for
DS1 A, disables EASY-MENU alarmsfor DS1 A, and stops
data transmission for DS1 A.
'enabled' reverses the effect of 'disabled'.rw Enumeration .1.3.6.1.4.1.664.2.9.2.13 |
adDAX3ds1BoperationThe DS1 Line B Operational Status.
'disabled' turns off the faceplate indicators for
DS1 B, disables EASY-MENU alarmsfor DS1 B, and stops
data transmission for DS1 B.
'enabled' reverses the effect of 'disabled'.rw Enumeration .1.3.6.1.4.1.664.2.9.2.14 |
adDAX3trunkProcessModeThis item indicates how trunk processing will be
initiated towards the channel units in the ACT bank
in response to a DS1 alarm. This item changes based
on the cross-connect matrix configuration.
'liuA' indicates that all connected digroup channels
connected to DS1 Line A and are configured as full
transparent connections. For an alarm on DS1 Line A
the normal bank facilities for trunk conditioning and
CGA code insertion will be used.
'liuB' indicates that all connected digroup channels
connected to DS1 Line B and are configured as full
transparent connections. For an alarm on DS1 Line B
the normal bank facilities for trunk conditioning and
CGA code insertion will be used.
'dax' indicates a cross connect matrix configuration
other than that for 'liuA' or 'liuB'. The ACT DAX will
initiate trunk processing toward all the DS0 channels
in the digroup on a channel by channel basis.ro Enumeration .1.3.6.1.4.1.664.2.9.2.15 |
adDAX3remPortBaudRateThe ACTDAX Remote Port Baud Rate. Changing the
remote port buad rate WILL TERMINATE communications
to this device at the current baud rate.rw Enumeration .1.3.6.1.4.1.664.2.9.2.16 |
adDAX3remPortProtocolThe ACTDAX Remote Port Protocol.ro Enumeration .1.3.6.1.4.1.664.2.9.2.17 |
adDAX3remPortConnectThe ACTDAX Remote Port Connection Type. Changing
the connection type may disrupt communication
to this device.
'direct' indicates a direct connection to the
proxy agent.
'dialUp' indicates a dial-Up connection to the
proxy agent. The adDAX3phone should be set.rw Enumeration .1.3.6.1.4.1.664.2.9.2.18 |
adDAX3phoneThe dialing sequence (phone number) to reach the
network manager. Maximum of 35 characters.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.9.2.19 |
adDAX3mdmInitCmdThe modem initialization command string. The
initialization string will be sent to the modem on
unit power-up, before a call is made, and on user
command. Maximum of 40 characters. Any control
character should be entered as '^' plus the character.
The factory default is 'ATE0Q0V1X4&C1&D2S0=1^M'.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.9.2.20 |
adDAX3mdmDialCmdThe modem dialing command string. The dialing
command will be sent to the modem before the phone
number. Maximum of 15 characters.
The factory default is 'ATDT'.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.9.2.21 |
adDAX3mdmDialCmdSfxThe modem dialing command suffix. The dialing
command suffix will be sent to the modem after the
phone number. Maximum of 5 characters. Any control
character should be entered as '^' plus the character.
The factory default is '^M'.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.9.2.22 |
adDAX3mdmHangUpCmdThe modem hang-up command. The hang-up command will
be sent to the modem to hang-up the line. Maximum of
15 characters. Any control character should be
entered as '^' plus the character. The first three
characters should be the escape code sequence for
the modem.
The factory default is '+++ATH^M'.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.9.2.23 |
adDAX3mdmInitA Set will send the modem initialization string to
the modem connected to the remote port.
This WILL DISRUPT communications to this device.rw INTEGER .1.3.6.1.4.1.664.2.9.2.24 |
adDAX3daisyChainDisable/Enable the Local Rear Panel Port of the
ACTDAX for Daisy Chain operation.
'off' indicates that the Local Rear Panel Port
will run the EASYMENU terminal interface.
'on' indicates that the Local Rear Panel Port
can be connected to the remote port of the next
unit downstream from the proxy agent.rw Enumeration .1.3.6.1.4.1.664.2.9.2.25 |
adDAX3unitMapThe ACT DAX channel configuration table which shows
what intelligent devices are active in each channel. SEQUENCE OF AdDAX3unit .1.3.6.1.4.1.664.2.9.3 |
adDAX3unit AdDAX3unit .1.3.6.1.4.1.664.2.9.3.1 |
adDAX3chanNumberThe channel number of this table entryro INTEGER .1.3.6.1.4.1.664.2.9.3.1.1 |
adDAX3chanUnitThe unit name plugged into this channel slot,
for example, DSUDPro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.9.3.1.2 |
adDAX3device-2The device name of the PM loop unit connected
to the channel unit, for example, LR-IVro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.9.3.1.3 |
adDAX3device-3The device name of the PM loop unit connected
to a secondary loop, for example, DDST-IVro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.9.3.1.4 |
adDAX3device-4The device name of the PM loop unit connected
to a secondary loop, for example, DDST-IVro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.9.3.1.5 |
adDAX3device-5The device name of the PM loop unit connected
to a secondary loop, for example, DDST-IVro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.9.3.1.6 |
adDAX3connTableThe ACTDAX cross-connect matrix table. SEQUENCE OF AdDAX3connEntry .1.3.6.1.4.1.664.2.9.4 |
adDAX3connEntryAn entry in the ACTDAX cross-connect matrix table. AdDAX3connEntry .1.3.6.1.4.1.664.2.9.4.1 |
adDAXFromPortThis object is the identifier of one of the three ports.
The ACTDAX serves a a cross-point matrix switch between 72
total DS0 channels distributed in three ports of 24 channels
each, and can be configured to cross-connect any of the 72
DS0 channels to any other DS0 channel. The three ports
are the DS1 Line A port (a1), the DS1 Line B port (b1),
and the channel bank (a0). This object in combination
with adDAXFromChannel defines one of the 72 DS0 channels
which can be connected.ro Enumeration .1.3.6.1.4.1.664.2.9.4.1.1 |
adDAXFromChannelThis object is the identifier of one of the 24 channels
in the DS1 port identified by adDAXFromPort. For 'a1' or
'b1' this object identifies a time slot in the DS1 stream.
For 'a0' this object identifies a physical channel slot
in the channel bank.ro INTEGER .1.3.6.1.4.1.664.2.9.4.1.2 |
adDAXConnStatusThe Connection Status for the channel.
'unmapped' indicates that the channel is not connected.
'connected' indicates that the channel is connected to
the channel indicated by adDAXToPort and adDAXToChannel
with the attributes defined by the other objects in
adDAX3connTable.
All connections are two-way connections, therefore any
set operation performed will also change the corresponding
table entry for which the To channel is the From channel.
In short, any connection can be identified by either side
of the connection. The From and To designations have no
true directional significance but are used to differentiate
between the two sides of the circuit for assigning circuit
parameters. To channels and circuit parameters can be
assigned but will not take affect until this object is
set to 'connected'.rw Enumeration .1.3.6.1.4.1.664.2.9.4.1.3 |
adDAXToPortThe port of the DS0 channel connected to the channel
indicated by adDAXFromPort and adDAXFromChannel. The
three possible ports are the DS1 Line A port (a1),
the DS1 Line B port (b1), and the channel bank (a0).rw Enumeration .1.3.6.1.4.1.664.2.9.4.1.4 |
adDAXToChannelThe channel in adDAXToPort that is connected to the
channel indicated by adDAXFromPort and adDAXFromChannel.rw INTEGER .1.3.6.1.4.1.664.2.9.4.1.5 |
adDAXCircuitTypeThe ciruit type for the connection. The ciruit type will
determine the settings for adDAXSgnlState, adDAXTroubleInsert,
adDAXTroubleCode, adDAXFromTC, and adDAXToTC. For voice
circuit types such as 'fxo-fxs', 'fxo' represents the from
channel and 'fxs' represents the to channel.
'fullTransparent' indicates SgnlState=transparent,
TroubleInsert=no, FromTC=none, and ToTC=none.
'dataTransparent' indicates SgnlState=transparent,
TroubleCode=9Ah, FromTC=none, and ToTC=none.
'dataSW56' indicates SgnlState=2state, TroubleCode=9Ah,
FromTC=0000, ToTC=0000.
'voiceTransparent' indicates SgnlState=transparent,
TroubleCode=7Fh, FromTC=none, and ToTC=none.
'dpt-dpo' indicates SgnlState=2state, TroubleCode=7Fh,
FromTC=0000, ToTC=0011.
'dpo-dpt' indicates SgnlState=2state, TroubleCode=7Fh,
FromTC=0011, ToTC=0000.
'fxo-fxs' indicates SgnlState=4state, TroubleCode=7Fh,
FromTC=0100, ToTC=1101.
'fxs-fxo' indicates SgnlState=4state, TroubleCode=7Fh,
FromTC=1101, ToTC=0100.
'em' indicates SgnlState=2state, TroubleCode=7Fh,
FromTC=0011, ToTC=0011.
'plar-d3' indicates SgnlState=2state, TroubleCode=7Fh,
FromTC=0000, ToTC=0000.
'plar-d4' indicates SgnlState=2state, TroubleCode=7Fh,
FromTC=1111, ToTC=1111.rw Enumeration .1.3.6.1.4.1.664.2.9.4.1.6 |
adDAXTerminationThe termination status of the circuit. Terminating the
circuit in one direction is equivalent to not connecting
the circuit in that direction. The Unassigned Channel
Code will be transmitted in that direction of the circuit
instead of circuit data. In addition, if the Trunk
Conditioning signaling bit states are defined, then the
post 2.5 second trunk conditioning signaling bits will be
inserted in that direction.rw Enumeration .1.3.6.1.4.1.664.2.9.4.1.7 |
adDAXSgnlStateThe signaling state of the circuit.
'transparent' indicates that no signal bit robbing is
performed.
'state2' indicates that the A-bit is robbed and inserted
in both the A-bit and B-bit positions in the outgoing
data stream.
'state4' indicates that both the A-bit and B-bit are
robbed and inserted in the outgoing data stream.
'state16' indicates that the A-bit, B-bit, C-bit, and D-bit
are robbed and inserted in the outgoing data stream. The
16-state signaling can only be set for connections between
the DS1 lines and then only if the DS1 lines are configured
for ESF framing.rw Enumeration .1.3.6.1.4.1.664.2.9.4.1.8 |
adDAXTroubleInsertIf the source channel's port is in an alarm state, the
the Trouble Insertion Code will be inserted toward the
DS0 channel in place of the outgoing data. The available
options include two common trouble codes, TRB (7f hex) and
MOS (9a hex). The Trouble Insertion Code can be set to
None to have no Trouble Code inserted and to allow the
outgoing data to pass through in alarm conditions. The
Trouble Code may also be set to a custom hex value
with adACTDAXTroubleCode when this object is set to
'userDefined'.rw Enumeration .1.3.6.1.4.1.664.2.9.4.1.9 |
adDAXTroubleCodeThe Trouble Insertion Code that will be inserted toward
a DS0 channel instead of outgoing data when the source
channels's port is in an alarm state. The TroubleCode
will be the same for both the From and To channels. If
adDAXTroubleInsert is set to 'none', then the Trouble Code
will show 'N/A'. The Trouble Code should be entered as
a two digit hex value, i.e. '9A' for a hex value of 9Ah.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.9.4.1.10 |
adDAXFromTCThe trunk conditioning bits that will be inserted in
the From channel in place of received signaling bits
during an alarm state on the To channel port. The first
two bits will be inserted for the A-bit and B-bit,
respectively, during the first 2.5 seconds of the alarm.
The second two bits will be inserted for the A-bit and
B-bit, respectively, after the first 2.5 seconds of the
alarm until the alarm clears. For example, if '0110'
is chosen, then during the first 2.5 seconds of the alarm
the A-bit will be '0' and the B-bit will be '1'. After
the first 2.5 seconds the A-bit will be '1' and the B-bit
will be '0'.rw Enumeration .1.3.6.1.4.1.664.2.9.4.1.11 |
adDAXToTCThe trunk conditioning bits that will be inserted in
the To channel in place of received signaling bits during
an alarm state on the From channel port. The first
two bits will be inserted for the A-bit and B-bit,
respectively, during the first 2.5 seconds of the alarm.
The second two bits will be inserted for the A-bit and
B-bit, respectively, after the first 2.5 seconds of the
alarm until the alarm clears. For example, if '0110'
is chosen, then during the first 2.5 seconds of the alarm
the A-bit will be '0' and the B-bit will be '1'. After
the first 2.5 seconds the A-bit will be '1' and the B-bit
will be '0'.rw Enumeration .1.3.6.1.4.1.664.2.9.4.1.12 |
adDAXUACThe Unassigned Channel Code (UAC) is transmitted towards
the From channel when the channel is not not assigned to
a connection, or the channel is terminated in a connection.
The factory default is Command Mode Idle (FEh). The
Unassigned Channel Code should be entered as a two digit
hex value, i.e. 'FE' for a hex value of FEh.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.9.4.1.13 |
adDAXZeroCodeSuppressThis object indicates if Zero Code Suppression is enabled
or disabled for the from channel. If Zero Code Suppression
is enabled, zero bytes transmitted from the DS1 interface
for this channel will be replaced with the code '00000010'.
Zero Code Suppression does not apply to DS0 channels in the
'a0' port.rw Enumeration .1.3.6.1.4.1.664.2.9.4.1.14 |
adDAXlastSetResponseThe response to the last set operation performed on
an object in this table. The repsonse indicates either
SUCCESS or an explanation of failure.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.9.4.1.15 |
adDAX3connMapTableThe ACTDAX cross-connect map table. SEQUENCE OF AdDAX3connMapEntry .1.3.6.1.4.1.664.2.9.5 |
adDAX3connMapEntryAn entry in the ACTDAX cross-connect map table. AdDAX3connMapEntry .1.3.6.1.4.1.664.2.9.5.1 |
adDAXPortThis object is the identifier of one of the three ports.
The ACTDAX serves a a cross-point matrix switch between 72
total DS0 channels distributed in three ports of 24 channels
each, and can be configured to cross-connect any of the 72
DS0 channels to any other DS0 channel. The three ports
are the DS1 Line A port (a1), the DS1 Line B port (b1),
and the channel bank (a0).ro Enumeration .1.3.6.1.4.1.664.2.9.5.1.1 |
adDAXChnl1The DSO channel connected to channel 1 of adDAXPort.ro Enumeration .1.3.6.1.4.1.664.2.9.5.1.2 |
adDAXChnl2The DSO channel connected to channel 2 of adDAXPort.ro Enumeration .1.3.6.1.4.1.664.2.9.5.1.3 |
adDAXChnl3The DSO channel connected to channel 3 of adDAXPort.ro Enumeration .1.3.6.1.4.1.664.2.9.5.1.4 |
adDAXChnl4The DSO channel connected to channel 4 of adDAXPort.ro Enumeration .1.3.6.1.4.1.664.2.9.5.1.5 |
adDAXChnl5The DSO channel connected to channel 5 of adDAXPort.ro Enumeration .1.3.6.1.4.1.664.2.9.5.1.6 |
adDAXChnl6The DSO channel connected to channel 6 of adDAXPort.ro Enumeration .1.3.6.1.4.1.664.2.9.5.1.7 |
adDAXChnl7The DSO channel connected to channel 7 of adDAXPort.ro Enumeration .1.3.6.1.4.1.664.2.9.5.1.8 |
adDAXChnl8The DSO channel connected to channel 8 of adDAXPort.ro Enumeration .1.3.6.1.4.1.664.2.9.5.1.9 |
adDAXChnl9The DSO channel connected to channel 9 of adDAXPort.ro Enumeration .1.3.6.1.4.1.664.2.9.5.1.10 |
adDAXChnl10The DSO channel connected to channel 10 of adDAXPort.ro Enumeration .1.3.6.1.4.1.664.2.9.5.1.11 |
adDAXChnl11The DSO channel connected to channel 11 of adDAXPort.ro Enumeration .1.3.6.1.4.1.664.2.9.5.1.12 |
adDAXChnl12The DSO channel connected to channel 12 of adDAXPort.ro Enumeration .1.3.6.1.4.1.664.2.9.5.1.13 |
adDAXChnl13The DSO channel connected to channel 13 of adDAXPort.ro Enumeration .1.3.6.1.4.1.664.2.9.5.1.14 |
adDAXChnl14The DSO channel connected to channel 14 of adDAXPort.ro Enumeration .1.3.6.1.4.1.664.2.9.5.1.15 |
adDAXChnl15The DSO channel connected to channel 15 of adDAXPort.ro Enumeration .1.3.6.1.4.1.664.2.9.5.1.16 |
adDAXChnl16The DSO channel connected to channel 16 of adDAXPort.ro Enumeration .1.3.6.1.4.1.664.2.9.5.1.17 |
adDAXChnl17The DSO channel connected to channel 17 of adDAXPort.ro Enumeration .1.3.6.1.4.1.664.2.9.5.1.18 |
adDAXChnl18The DSO channel connected to channel 18 of adDAXPort.ro Enumeration .1.3.6.1.4.1.664.2.9.5.1.19 |
adDAXChnl19The DSO channel connected to channel 19 of adDAXPort.ro Enumeration .1.3.6.1.4.1.664.2.9.5.1.20 |
adDAXChnl20The DSO channel connected to channel 20 of adDAXPort.ro Enumeration .1.3.6.1.4.1.664.2.9.5.1.21 |
adDAXChnl21The DSO channel connected to channel 21 of adDAXPort.ro Enumeration .1.3.6.1.4.1.664.2.9.5.1.22 |
adDAXChnl22The DSO channel connected to channel 22 of adDAXPort.ro Enumeration .1.3.6.1.4.1.664.2.9.5.1.23 |
adDAXChnl23The DSO channel connected to channel 23 of adDAXPort.ro Enumeration .1.3.6.1.4.1.664.2.9.5.1.24 |
adDAXChnl24The DSO channel connected to channel 24 of adDAXPort.ro Enumeration .1.3.6.1.4.1.664.2.9.5.1.25 |
adDAX3systemEvent OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.9.6 |
adDAX3AlarmStatusThis bit map variable indicates alarm status for the
ACTDAX and the ACT 1241 channel bank. This item does
not include DS1 line status.
The various alarm event bit positions are:
1 System Hardware Failure
2 System Software Failure
4 Channel Bank Out Of Servicero INTEGER .1.3.6.1.4.1.664.2.9.6.1 |
adDAX3AlarmEnableThis bit map variable arms or disarms an individual or
group of events identified in adDAX3AlarmStatus as a source
for generation of System Alarm Trap.
The various arm event bit positions are:
1 System Hardware Failure
2 System Software Failure
4 Channel Bank Out Of Servicerw INTEGER .1.3.6.1.4.1.664.2.9.6.2 |
adDAX3sysAlarmThis item can be polled to determine if there are any
active alarms on the ACTDAX or its corresponding
intelligent units.ro Enumeration .1.3.6.1.4.1.664.2.9.6.3 |
adDAX3sysAlarmEnableThis is a global enable/disable for all enterprise traps
from this node controller.rw Enumeration .1.3.6.1.4.1.664.2.9.6.4 |
adDAX3LedStatusThis variable contains bit encoded values for the
ACTDAX LED status:
1 RLBK-A (1=off, 0=yellow)
2 ESF-A (1=off, 0=green)
4 B8ZS-A (1=off, 0=green)
8 RLBK-B (1=off, 0=yellow)
16 ESF-B (1=off, 0=green)
32 B8ZS-B (1=off, 0=green)
64 TEST (1=off, 0=yellow)
128 unused
256 DS1-A combine with next bit
512 (00=off, 01=red, 10=green, 11=yellow)
1024 DS1-B combine with next bit
2048 (00=off, 01=red, 10=green, 11=yellow)
4096 STAT combine with next bit
8192 (00=off, 01=red, 10=green)
16384 DS0-PM combine with next bit
32768 (00=off, 01=red, 10=green).ro INTEGER .1.3.6.1.4.1.664.2.9.6.5 |
adDAX3ds1EventTableThe DS1 Alarm/Alert Event Table. SEQUENCE OF AdDAX3ds1EventEntry .1.3.6.1.4.1.664.2.9.7 |
adDAX3ds1EventEntryAn entry in the DS1 Alarm/Alert Event Table. AdDAX3ds1EventEntry .1.3.6.1.4.1.664.2.9.7.1 |
adDAX3ds1EventIndexThe index value which uniquely identifies the DS1
interface. The interface identified by a particular
value of this index is the same interface as identified
by dsx1LineIndex in DS1 MIB.ro INTEGER(1..'7fffffff'h) .1.3.6.1.4.1.664.2.9.7.1.1 |
adDAX3LineStatusThis bit map variable indicates both alarm and loopback
status for the DS1 Line.
The various alarm event bit positions are:
1 Far end LOF ( a.k.a., Yellow Alarm )
2 Near end sending LOF Indication
4 Far end sending AIS ( Blue Alarm )
8 Near end sending AIS
16 Near end LOF ( a.k.a., Red Alarm )
32 Near end Loss Of Signal
64 Near end Local Loopback
128 Near end Line Loopback
256 Near end Payload Loopback
512 Far end Requested Line Loopback
1024 Far end Requested Payload Loopback
2048 Far end in Line Loopback (commanded from near end)
4096 Far end in Payload Loopback (commanded from near end)ro INTEGER .1.3.6.1.4.1.664.2.9.7.1.2 |
adDAX3LineArmThis bit map variable arms or disarms an individual or
group of events identified in adDAX3LineStatus as a source
for generation of DS1 Alarm Trap.
The various arm event bit positions are:
1 Far end LOF ( a.k.a., Yellow Alarm )
2 Near end sending LOF Indication
4 Far end sending AIS ( Blue Alarm )
8 Near end sending AIS
16 Near end LOF ( a.k.a., Red Alarm )
32 Near end Loss Of Signal
64 Near end Local Loopback
128 Near end Line Loopback
256 Near end Payload Loopback
512 Far end Requested Line Loopback
1024 Far end Requested Payload Loopback
2048 Far end in Line Loopback (commanded from near end)
4096 Far end in Payload Loopback (commanded from near end)rw INTEGER .1.3.6.1.4.1.664.2.9.7.1.3 |
adDAX3CurrentAlertThis DS1 performance status variable indicates Threshold
Crossing Alerts for Near End Current 15 minute interval.
An alert bit is set in this variable when the value of
the dsx1CurrentTable object exceeds the Threshold Value.
This variable contains the sum of alert values.
Threshold Crossing Alert bit position values:
1 ES - Errored Seconds
2 SES - Severely Errored Seconds
4 SEFS - Severely Errored Framing Seconds
8 UAS - Unavailable Seconds
16 CSS - Controlled Slip Seconds
32 PCV - Path Coding Violations
64 LES - Line Errored Seconds
128 BES - Bursty Errored Seconds
256 DM - Degraded Minutes
512 LCV - Line Code Violationsro INTEGER .1.3.6.1.4.1.664.2.9.7.1.4 |
adDAX3TotalAlertThis DS1 performance status variable indicates Threshold
Crossing Alerts for Near End Total performance variables.
An alert bit is set in this variable when the value of
the dsx1TotalTable object exceeds the Threshold Value.
This variable contains the sum of alert values.
Threshold Crossing Alert bit position values:
1 ES - Errored Seconds
2 SES - Severely Errored Seconds
4 SEFS - Severely Errored Framing Seconds
8 UAS - Unavailable Seconds
16 CSS - Controlled Slip Seconds
32 PCV - Path Coding Violations
64 LES - Line Errored Seconds
128 BES - Bursty Errored Seconds
256 DM - Degraded Minutes
512 LCV - Line Code Violationsro INTEGER .1.3.6.1.4.1.664.2.9.7.1.5 |
adDAX3FarCurrentAlertThis DS1 performance status variable indicates Threshold
Crossing Alerts for Far End Current 15 minute interval.
An alert bit is set in this variable when the value of
the dsx1FarEndCurrentTable object exceeds the Threshold
Value. This variable contains the sum of alert values.
Threshold Crossing Alert bit position values:
1 ES - Errored Seconds
2 SES - Severely Errored Seconds
4 SEFS - Severely Errored Framing Seconds
8 UAS - Unavailable Seconds
16 CSS - Controlled Slip Seconds
32 PCV - Path Coding Violations
64 LES - Line Errored Seconds
128 BES - Bursty Errored Seconds
256 DM - Degraded Minutesro INTEGER .1.3.6.1.4.1.664.2.9.7.1.6 |
adDAX3FarTotalAlertThis DS1 performance status variable indicates Threshold
Crossing Alerts for Far End Total performance variables.
An alert bit is set in this variable when the value of
the dsx1FarEndTotalTable object exceeds the Threshold
Value. This variable contains the sum of alert values.
Threshold Crossing Alert bit position values:
1 ES - Errored Seconds
2 SES - Severely Errored Seconds
4 SEFS - Severely Errored Framing Seconds
8 UAS - Unavailable Seconds
16 CSS - Controlled Slip Seconds
32 PCV - Path Coding Violations
64 LES - Line Errored Seconds
128 BES - Bursty Errored Seconds
256 DM - Degraded Minutesro INTEGER .1.3.6.1.4.1.664.2.9.7.1.7 |
adDAX3CurrentArmThis variable arms and disarms an individual or group
of alerts identified in adDAX3CurrentAlert as a source
for the generation of Threshold Crossing Alert Trap.
This variable contains the sum of Arm values.
Threshold Crossing Arm bit position values:
1 ES - Errored Seconds
2 SES - Severely Errored Seconds
4 SEFS - Severely Errored Framing Seconds
8 UAS - Unavailable Seconds
16 CSS - Controlled Slip Seconds
32 PCV - Path Coding Violations
64 LES - Line Errored Seconds
128 BES - Bursty Errored Seconds
256 DM - Degraded Minutes
512 LCV - Line Code Violationsrw INTEGER .1.3.6.1.4.1.664.2.9.7.1.8 |
adDAX3TotalArmThis variable arms and disarms an individual or group
of alerts identified in adDAX3TotalAlert as a source
for the generation of Threshold Crossing Alert Trap.
This variable contains the sum of Arm values.
Threshold Crossing Arm bit position values:
1 ES - Errored Seconds
2 SES - Severely Errored Seconds
4 SEFS - Severely Errored Framing Seconds
8 UAS - Unavailable Seconds
16 CSS - Controlled Slip Seconds
32 PCV - Path Coding Violations
64 LES - Line Errored Seconds
128 BES - Bursty Errored Seconds
256 DM - Degraded Minutes
512 LCV - Line Code Violationsrw INTEGER .1.3.6.1.4.1.664.2.9.7.1.9 |
adDAX3FarCurrentArmThis variable arms and disarms an individual or group
of alerts identified in adDAX3FarCurrentAlert as a source
for the generation of Threshold Crossing Alert Trap.
This variable contains the sum of Arm values.
Threshold Crossing Arm bit position values:
1 ES - Errored Seconds
2 SES - Severely Errored Seconds
4 SEFS - Severely Errored Framing Seconds
8 UAS - Unavailable Seconds
16 CSS - Controlled Slip Seconds
32 PCV - Path Coding Violations
64 LES - Line Errored Seconds
128 BES - Bursty Errored Seconds
256 DM - Degraded Minutesrw INTEGER .1.3.6.1.4.1.664.2.9.7.1.10 |
adDAX3FarTotalArmThis variable arms and disarms an individual or group
of alerts identified in adDAX3FarTotalAlert as a source
for the generation of Threshold Crossing Alert Trap.
This variable contains the sum of Arm values.
Threshold Crossing Arm bit position values:
1 ES - Errored Seconds
2 SES - Severely Errored Seconds
4 SEFS - Severely Errored Framing Seconds
8 UAS - Unavailable Seconds
16 CSS - Controlled Slip Seconds
32 PCV - Path Coding Violations
64 LES - Line Errored Seconds
128 BES - Bursty Errored Seconds
256 DM - Degraded Minutesrw INTEGER .1.3.6.1.4.1.664.2.9.7.1.11 |
adDAX3CurrentThrsTableThe DS1 Current Threshold Table. SEQUENCE OF AdDAX3CurrentThrsEntry .1.3.6.1.4.1.664.2.9.8 |
adDAX3CurrentThrsEntryAn entry in the DS1 Current Threshold Table. AdDAX3CurrentThrsEntry .1.3.6.1.4.1.664.2.9.8.1 |
adDAX3CurrentThrsIndexThe index value which uniquely identifies the DS1
interface. The interface identified by a particular
value of this index is the same interface as identified
by dsx1LineIndex in DS1 MIB.ro INTEGER(1..'7fffffff'h) .1.3.6.1.4.1.664.2.9.8.1.1 |
adDAX3CurrentThrsESThe DS1 performance monitor Threshold Value for the
Current 15 minute Errored Seconds parameter. The
default value is 65 for an approximate BER level of
(10** -5).rw INTEGER .1.3.6.1.4.1.664.2.9.8.1.2 |
adDAX3CurrentThrsSESThe DS1 performance monitor Threshold Value for the
Current 15 minute Severely Errored Seconds parameter.
The default value is 10 for an approximate BER level of
(10** -5).rw INTEGER .1.3.6.1.4.1.664.2.9.8.1.3 |
adDAX3CurrentThrsSEFSThe DS1 performance monitor Threshold Value for the
Current 15 minute Severely Errored Framing Seconds
parameter. The default value is 2 for an approximate
BER level of (10** -5).rw INTEGER .1.3.6.1.4.1.664.2.9.8.1.4 |
adDAX3CurrentThrsUASThe DS1 performance monitor Threshold Value for the
Current 15 minute Unavailable Seconds parameter. The
default value is 10 for an approximate BER level of
(10** -5).rw INTEGER .1.3.6.1.4.1.664.2.9.8.1.5 |
adDAX3CurrentThrsCSSThe DS1 performance monitor Threshold Value for the
Current 15 minute Controlled Slip Seconds parameter.
The default value is 1 for an approximate BER level of
(10** -5).rw INTEGER .1.3.6.1.4.1.664.2.9.8.1.6 |
adDAX3CurrentThrsPCVsfThe DS1 performance monitor Threshold Value for the
Current 15 minute Path Coding Violations parameter,
when the Line Type is Super Frame (AT&T D4 format) DS1.
Default value for an approximate BER level of (10**-5)
is 72 Framing errors.rw INTEGER .1.3.6.1.4.1.664.2.9.8.1.7 |
adDAX3CurrentThrsPCVesfThe DS1 performance monitor Threshold Value for the
Current 15 minute Path Coding Violations parameter,
when the Line Type is Extended Super Frame (ESF) DS1.
Default value for an approximate BER level of (10**-5)
is 13,296 CRC errors.rw INTEGER .1.3.6.1.4.1.664.2.9.8.1.8 |
adDAX3CurrentThrsLESThe DS1 performance monitor Threshold Value for the
Current 15 minute Line Errored Seconds parameter.
The default value is 65 for an approximate BER level of
(10** -5).rw INTEGER .1.3.6.1.4.1.664.2.9.8.1.9 |
adDAX3CurrentThrsBESThe DS1 performance monitor Threshold Value for the
Current 15 minute Bursty Errored Seconds parameter.
The default value is ?? for an approximate BER level of
(10** -5).rw INTEGER .1.3.6.1.4.1.664.2.9.8.1.10 |
adDAX3CurrentThrsLCVThe DS1 performance monitor Threshold Value for the
Current 15 minute Line Code Violations parameter. The
default value is 13,340 for an approximate BER level of
(10** -5).rw INTEGER .1.3.6.1.4.1.664.2.9.8.1.11 |
adDAX3TotalThrsTableThe DS1 Total Threshold Table. SEQUENCE OF AdDAX3TotalThrsEntry .1.3.6.1.4.1.664.2.9.9 |
adDAX3TotalThrsEntryAn entry in the DS1 Total Threshold Table. AdDAX3TotalThrsEntry .1.3.6.1.4.1.664.2.9.9.1 |
adDAX3TotalThrsIndexThe index value which uniquely identifies the DS1
interface. The interface identified by a particular
value of this index is the same interface as identified
by dsx1LineIndex in DS1 MIB.ro INTEGER(1..'7fffffff'h) .1.3.6.1.4.1.664.2.9.9.1.1 |
adDAX3TotalThrsESThe DS1 performance monitor Threshold Value for the
Total Errored Seconds parameter. The default value
is 648 for an approximate BER level of (10** -5).rw INTEGER .1.3.6.1.4.1.664.2.9.9.1.2 |
adDAX3TotalThrsSESThe DS1 performance monitor Threshold Value for the
Total Severely Errored Seconds parameter. The default
value is 100 for an approximate BER level of (10** -5).rw INTEGER .1.3.6.1.4.1.664.2.9.9.1.3 |
adDAX3TotalThrsSEFSThe DS1 performance monitor Threshold Value for the
Total Severely Errored Framing Seconds parameter. The
default value is 17 for an approximate BER level of
(10** -5).rw INTEGER .1.3.6.1.4.1.664.2.9.9.1.4 |
adDAX3TotalThrsUASThe DS1 performance monitor Threshold Value for the
Total Unavailable Seconds parameter. The default value
is 10 for an approximate BER level of (10** -5).rw INTEGER .1.3.6.1.4.1.664.2.9.9.1.5 |
adDAX3TotalThrsCSSThe DS1 performance monitor Threshold Value for the
Total Controlled Slip Seconds parameter. The default
value is 4 for an approximate BER level of(10** -5).rw INTEGER .1.3.6.1.4.1.664.2.9.9.1.6 |
adDAX3TotalThrsPCVsfThe DS1 performance monitor Threshold Value for the
Total Path Coding Violations parameter, when the Line
Type is Super Frame (AT&T D4 format) DS1. The default
value for an approximate BER level of (10**-5) is 691
framing errors.rw INTEGER .1.3.6.1.4.1.664.2.9.9.1.7 |
adDAX3TotalThrsPCVesfThe DS1 performance monitor Threshold Value for the
Total Path Coding Violations parameter, when the Line
Type is Extended Super Frame (ESF) DS1. The default
value for an approximate BER level of (10**-5) is
132,960 CRC errors.rw INTEGER .1.3.6.1.4.1.664.2.9.9.1.8 |
adDAX3TotalThrsLESThe DS1 performance monitor Threshold Value for the
Total Line Errored Seconds parameter. The default value
is 648 for an approximate BER level of (10** -5).rw INTEGER .1.3.6.1.4.1.664.2.9.9.1.9 |
adDAX3TotalThrsBESThe DS1 performance monitor Threshold Value for the
Total Bursty Errored Seconds parameter. The default value
is ??? for an approximate BER level of (10** -5).rw INTEGER .1.3.6.1.4.1.664.2.9.9.1.10 |
adDAX3TotalThrsLCVThe DS1 performance monitor Threshold Value for the
Total Line Code Violations parameter. The default value
is 133,400 for an approximate BER level of (10** -5).rw INTEGER .1.3.6.1.4.1.664.2.9.9.1.11 |
adDS1DailyIntervalTableThe DS1 Daily Interval Table. SEQUENCE OF AdDS1DailyIntervalEntry .1.3.6.1.4.1.664.2.9.10 |
adDS1DailyIntervalEntryAn entry in the DS1 Daily Interval Table. AdDS1DailyIntervalEntry .1.3.6.1.4.1.664.2.9.10.1 |
adDS1DailyIntervalIndexThe index value which uniquely identifies the
DS1 interface to which this entry is applicable.
The interface identified by a particular value
of this index is the same interface as identified
by the same value as a dsx1LineIndex object
instance.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.664.2.9.10.1.1 |
adDS1DailyIntervalNumberA number between 1 and 6, where 1 is the most
recently completed 15 minute interval and 6 is
the least recently completed daily interval
(assuming that all 6 intervals are valid).ro INTEGER .1.3.6.1.4.1.664.2.9.10.1.2 |
adDS1DailyIntervalValidIndicates if this daily interval contains valid data.ro Enumeration .1.3.6.1.4.1.664.2.9.10.1.3 |
adDS1DailyIntervalESsThe number of Errored Seconds encountered by a
DS1 interface in one of the prevoius daily intervals.ro Gauge .1.3.6.1.4.1.664.2.9.10.1.4 |
adDS1DailyIntervalSESsThe number of Severely Errored Seconds encountered
by a DS1 interface in one of the previous daily
intervals.ro Gauge .1.3.6.1.4.1.664.2.9.10.1.5 |
adDS1DailyIntervalSEFSsThe number of Severely Errored Framing Seconds
encountered by a DS1 interface in one of the
previous daily intervals.ro Gauge .1.3.6.1.4.1.664.2.9.10.1.6 |
adDS1DailyIntervalUASsThe number of Unavailable Seconds encountered
by a DS1 interface in one of the previous daily
intervals.ro Gauge .1.3.6.1.4.1.664.2.9.10.1.7 |
adDS1DailyIntervalCSSsThe number of Controlled Slip Seconds encountered
by a DS1 interface in one of the previous daily
intervals.ro Gauge .1.3.6.1.4.1.664.2.9.10.1.8 |
adDS1DailyIntervalPCVsThe number of Path Coding Violations encountered
by a DS1 interface in one of the previous daily
intervals.ro Gauge .1.3.6.1.4.1.664.2.9.10.1.9 |
adDS1DailyIntervalLESsThe number of Line Errored Seconds encountered
by a DS1 interface in one of the previous daily
intervals.ro Gauge .1.3.6.1.4.1.664.2.9.10.1.10 |
adDS1DailyIntervalBESsThe number of Bursty Errored Seconds encountered
by a DS1 interface in one of the previous daily
intervals.ro Gauge .1.3.6.1.4.1.664.2.9.10.1.11 |
adDS1DailyIntervalDMsThe number of Degraded Minutes encountered by
a DS1 interface in one of the previous daily
intervals.ro Gauge .1.3.6.1.4.1.664.2.9.10.1.12 |
adDS1DailyIntervalLCVsThe number of Line Code Violations encountered
by a DS1 interface in one of the previous daily
intervals.ro Gauge .1.3.6.1.4.1.664.2.9.10.1.13 |
adDS1FarEndDailyIntervalTableThe DS1 Daily Interval Table. SEQUENCE OF AdDS1FarEndDailyIntervalEntry .1.3.6.1.4.1.664.2.9.11 |
adDS1FarEndDailyIntervalEntryAn entry in the DS1 Daily Interval Table. AdDS1FarEndDailyIntervalEntry .1.3.6.1.4.1.664.2.9.11.1 |
adDS1FarEndDailyIntervalIndexThe index value which uniquely identifies the
DS1 interface to which this entry is applicable.
The interface identified by a particular value
of this index is the same interface as identified
by the same value as a dsx1LineIndex object
instance.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.664.2.9.11.1.1 |
adDS1FarEndDailyIntervalNumberA number between 1 and 6, where 1 is the most
recently completed 15 minute interval and 6 is
the least recently completed daily interval
(assuming that all 6 intervals are valid).ro INTEGER .1.3.6.1.4.1.664.2.9.11.1.2 |
adDS1FarEndDailyIntervalValidIndicates if this far end daily interval
contains valid data.ro Enumeration .1.3.6.1.4.1.664.2.9.11.1.3 |
adDS1FarEndDailyIntervalESsThe number of Far End Errored Seconds encountered
by a DS1 interface in one of the prevoius daily
intervals.ro Gauge .1.3.6.1.4.1.664.2.9.11.1.4 |
adDS1FarEndDailyIntervalSESsThe number of Far End Severely Errored Seconds
encountered by a DS1 interface in one of the
previous daily intervals.ro Gauge .1.3.6.1.4.1.664.2.9.11.1.5 |
adDS1FarEndDailyIntervalSEFSsThe number of Far End Severely Errored Framing
Seconds encountered by a DS1 interface in one
of the previous daily intervals.ro Gauge .1.3.6.1.4.1.664.2.9.11.1.6 |
adDS1FarEndDailyIntervalUASsThe number of Far End Unavailable Seconds
encountered by a DS1 interface in one of the
previous daily intervals.ro Gauge .1.3.6.1.4.1.664.2.9.11.1.7 |
adDS1FarEndDailyIntervalCSSsThe number of Far End Controlled Slip Seconds
encountered by a DS1 interface in one of the
previous daily intervals.ro Gauge .1.3.6.1.4.1.664.2.9.11.1.8 |
adDS1FarEndDailyIntervalPCVsThe number of Far End Path Coding Violations
encountered by a DS1 interface in one of the
previous daily intervals.ro Gauge .1.3.6.1.4.1.664.2.9.11.1.9 |
adDS1FarEndDailyIntervalLESsThe number of Far End Line Errored Seconds
encountered by a DS1 interface in one of the
previous daily intervals.ro Gauge .1.3.6.1.4.1.664.2.9.11.1.10 |
adDS1FarEndDailyIntervalBESsThe number of Far End Bursty Errored Seconds
encountered by a DS1 interface in one of the
previous daily intervals.ro Gauge .1.3.6.1.4.1.664.2.9.11.1.11 |
adDS1FarEndDailyIntervalDMsThe number of Far End Degraded Minutes
encountered by a DS1 interface in one of
the previous daily intervals.ro Gauge .1.3.6.1.4.1.664.2.9.11.1.12 |
adDS1FarEndDailyIntervalLCVsThe number of Far End Line Code Violations
encountered by a DS1 interface in one of the
previous daily intervals.ro Gauge .1.3.6.1.4.1.664.2.9.11.1.13 |