ADTRAN-ADUNIT-MIB
AI MIB Summary
The ADTRAN-ADUNIT-MIB facilitates the monitoring and configuration of general system parameters, including hardware status, operational state, and environmental metrics, on ADTRAN network units. It provides standardized SNMP access to device-level attributes such as interface states, power supply status, and system resource utilization for ADTRAN hardware platforms.
The MIB module for general unit configuration.
Main OID:
adtranUnitMib.1.3.6.1.4.1.664.5.30
169
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
169 total| Object Name |
|---|
adtranUnitMibThe MIB module for general unit configuration. MODULE-IDENTITY .1.3.6.1.4.1.664.5.30 |
adUnitInfo OBJECT IDENTIFIER .1.3.6.1.4.1.664.5.30.1 |
adUnitBootRevisionUnit boot PROM revision.ro DisplayString .1.3.6.1.4.1.664.5.30.1.1 |
adUnitConfig OBJECT IDENTIFIER .1.3.6.1.4.1.664.5.30.2 |
adUnitGenCfg OBJECT IDENTIFIER .1.3.6.1.4.1.664.5.30.2.1 |
adUnitDateTimeThe current unit date and time.rw DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.664.5.30.2.1.1 |
adUnitMaxTelnetAccessThe maximum number of active telnet sessions.rw Integer32 .1.3.6.1.4.1.664.5.30.2.1.2 |
adUnitEncryptPasswordsDetermines whether or not the locally stored user passwords are encrypted.rw Enumeration .1.3.6.1.4.1.664.5.30.2.1.3 |
adUnitEventLoggingEnable/Disable event logging on the unit.rw Enumeration .1.3.6.1.4.1.664.5.30.2.1.4 |
adUnitClearEventLogSet to 1 to clear all entries from unit's local event log.rw Integer32 (1) .1.3.6.1.4.1.664.5.30.2.1.5 |
adUserCfg OBJECT IDENTIFIER .1.3.6.1.4.1.664.5.30.2.2 |
adUnitUserTableA list of users who are allowed access to the unit. SEQUENCE OF AdUnitUserEntry .1.3.6.1.4.1.664.5.30.2.2.1 |
adUnitUserEntryEach entry in the list defines the user/pass, authen method, access level, and timeout. AdUnitUserEntry .1.3.6.1.4.1.664.5.30.2.2.1.1 |
adUnitUserIndexSequential index of the list of defined users. Integer32 .1.3.6.1.4.1.664.5.30.2.2.1.1.1 |
adUnitUserNameThe user name for access.rw DisplayString .1.3.6.1.4.1.664.5.30.2.2.1.1.2 |
adUnitUserAuthenMethodThe type of authentication to perform for this user.rw Enumeration .1.3.6.1.4.1.664.5.30.2.2.1.1.3 |
adUnitUserPasswdThe user passwordrw DisplayString .1.3.6.1.4.1.664.5.30.2.2.1.1.4 |
adUnitUserIdleTimeThe idle timeout value in minutes for a connection. If no operator activity is detected for this interval the connection is terminated. If the value is set to 0, the session will not be disconnected due to inactivity.rw Integer32 .1.3.6.1.4.1.664.5.30.2.2.1.1.5 |
adUnitUserLevelThis is the level of access this user has.rw Integer32 .1.3.6.1.4.1.664.5.30.2.2.1.1.6 |
adUnitUserIpAddrIf not null, the only IP address (or hostname) from which the specified user may initiate a telnet access.rw DisplayString .1.3.6.1.4.1.664.5.30.2.2.1.1.7 |
adUnitUserStateIndication of whether or not the user has an active session.ro Enumeration .1.3.6.1.4.1.664.5.30.2.2.1.1.8 |
adUnitUserStatusThe status of this conceptual row. Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the adUnitUserStatus column is 'notReady'.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.664.5.30.2.2.1.1.9 |
adSnmpCfg OBJECT IDENTIFIER .1.3.6.1.4.1.664.5.30.2.3 |
adUnitSNMPCommunitiesTableContains a list of users who have SNMP access to this unit. SEQUENCE OF AdUnitSNMPCommunitiesEntry .1.3.6.1.4.1.664.5.30.2.3.1 |
adUnitSNMPCommunitiesEntryEach entry in the list defines the community string, access privilege, and Manager IP address. AdUnitSNMPCommunitiesEntry .1.3.6.1.4.1.664.5.30.2.3.1.1 |
adUnitSNMPCommunitiesIndexIndex of the table. Integer32 .1.3.6.1.4.1.664.5.30.2.3.1.1.1 |
adUnitSNMPCommunitiesStringThe community string which has the specified SNMP access.rw DisplayString .1.3.6.1.4.1.664.5.30.2.3.1.1.2 |
adUnitSNMPCommunitiesPrivilegeSet the SNMP privileges of this user.rw Enumeration .1.3.6.1.4.1.664.5.30.2.3.1.1.3 |
adUnitSNMPCommunitiesMngmtIPThe IP address of the manager station. Set to '0.0.0.0' to enable the string for all addresses.rw IpAddress .1.3.6.1.4.1.664.5.30.2.3.1.1.4 |
adUnitSNMPCommunitiesStatusThe status of this conceptual row. Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the adUnitSNMPCommunitiesStatus column is 'notReady'.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.664.5.30.2.3.1.1.5 |
adUnitSNMPTrapsTableContains a list of users that will receive SNMP traps from this unit. SEQUENCE OF AdUnitSNMPTrapsEntry .1.3.6.1.4.1.664.5.30.2.3.2 |
adUnitSNMPTrapsEntryEach entry in the list defines the name, privilege, and Manager IP address. AdUnitSNMPTrapsEntry .1.3.6.1.4.1.664.5.30.2.3.2.1 |
adUnitSNMPTrapsIndexIndex of the table. Integer32 .1.3.6.1.4.1.664.5.30.2.3.2.1.1 |
adUnitSNMPTrapsStringThe community string included in the SNMP traps.rw DisplayString .1.3.6.1.4.1.664.5.30.2.3.2.1.2 |
adUnitSNMPTrapsMngmtAddrThe hostname (or IP address) that will receive SNMP traps.rw DisplayString .1.3.6.1.4.1.664.5.30.2.3.2.1.3 |
adUnitSNMPTrapsStatusThe status of this conceptual row. Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the adUnitSNMPTrapsStatus column is 'notReady'.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.664.5.30.2.3.2.1.4 |
adUnitSNMPEnableTrapsEnables or disables the transmission of all Traps.rw Enumeration .1.3.6.1.4.1.664.5.30.2.3.3 |
adUnitSNMPAuthenticationTrapsEnables or disables the transmission of Authentication Traps.rw Enumeration .1.3.6.1.4.1.664.5.30.2.3.4 |
adConsoleCfg OBJECT IDENTIFIER .1.3.6.1.4.1.664.5.30.2.4 |
adConsoleAccessModeSpecify operational mode of console. 0: No Authentication; no login required, CLI active automatically 1: Password Only 2: Username and password requiredrw Enumeration .1.3.6.1.4.1.664.5.30.2.4.1 |
adConsolePasswdThe password for the console.rw DisplayString .1.3.6.1.4.1.664.5.30.2.4.2 |
adConsoleLoginTimeoutSpecifies the amount of time the system will wait for user input for a username &/or password before timing out and resetting back to intial prompt state. The time is specified in seconds. If the value is set to 0, the session will not be disconnected due to inactivity. Some units may implement a maximum allowable which is less than that specified.rw Integer32 .1.3.6.1.4.1.664.5.30.2.4.3 |
adConsoleBaudRateThe baud rate for the console port.rw Enumeration .1.3.6.1.4.1.664.5.30.2.4.4 |
adConsoleDataBitsThe data bits for the console port.rw Enumeration .1.3.6.1.4.1.664.5.30.2.4.5 |
adConsoleParityThe parity scheme for the console port.rw Enumeration .1.3.6.1.4.1.664.5.30.2.4.6 |
adConsoleStopBitsThe number of stop bits for the console port.rw Enumeration .1.3.6.1.4.1.664.5.30.2.4.7 |
adConsoleFlowControlThe flow control mechanism for the console port. hardware control is via RTS/CTS and xOn/xOff is via transmission of the characters Control-S and Control-Q. Units may not support both control methods & hence may reject attempts to Set to ones not supported .rw Enumeration .1.3.6.1.4.1.664.5.30.2.4.8 |
adConsoleModemInitStringInitialization string to send to connected modem.rw DisplayString .1.3.6.1.4.1.664.5.30.2.4.9 |
adConsoleInitModemSet value to 1 to force unit to attempt to initialize a connected modem on the console port by sending the contents of adConsoleModemInitString.rw Integer32 (1) .1.3.6.1.4.1.664.5.30.2.4.10 |
adUnitSyslogCfg OBJECT IDENTIFIER .1.3.6.1.4.1.664.5.30.2.5 |
adUnitSyslogTransmissionEnables or disables the transmission of log events to the external Syslog server.rw Enumeration .1.3.6.1.4.1.664.5.30.2.5.1 |
adUnitSyslogSrvrNameThe Host IP Address specifies the hostname or IP address of the external server that is running the Syslog host daemon.rw DisplayString .1.3.6.1.4.1.664.5.30.2.5.2 |
adUnitSyslogHostFacilityThe Host Facility specifies the facility destination of log events. Facilities are located on the host and are managed by the Syslog host daemon running on either a UNIX machine or a PC.rw Enumeration .1.3.6.1.4.1.664.5.30.2.5.3 |
adUnitSyslogMinSeverityMinSeverity Level specifies the minimum level of severity that will cause messages to be logged to the Syslog server. The levels are listed in order of decreasing severity and any message at or above the selected severity level will be logged if transmission is enabled. 1. Emergency: system is unusable 2. Alert: action must be taken immediately 3. Critical: critical conditions 4. Error: error conditions 5. Warning: warning conditions 6. Notice: normal, but significant, conditions 7. Info: informational message 8. Debug: debug-level messagerw Enumeration .1.3.6.1.4.1.664.5.30.2.5.4 |
adUnitUtil OBJECT IDENTIFIER .1.3.6.1.4.1.664.5.30.3 |
adUnitGenUtil OBJECT IDENTIFIER .1.3.6.1.4.1.664.5.30.3.1 |
adUnitRebootSystemSet to 1 to initiate system reboot.rw Integer32 (1) .1.3.6.1.4.1.664.5.30.3.1.1 |
adUnitFactoryDefaultSystemSet to 1 to set factory defaults configuration values for the entire unit.rw Integer32 (1) .1.3.6.1.4.1.664.5.30.3.1.2 |
adUnitSchedResetTimeDate and Time of scheduled system reset.rw DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.664.5.30.3.1.3 |
adUpdtFirmware OBJECT IDENTIFIER .1.3.6.1.4.1.664.5.30.3.2 |
adUpdtFwXfrMethodMethod of downloading firmware to the unit.rw Enumeration .1.3.6.1.4.1.664.5.30.3.2.1 |
adUpdtFwTFTPSrvAddrThe hostname or IP address of the TFTP server.rw DisplayString .1.3.6.1.4.1.664.5.30.3.2.2 |
adUpdtFwTFTPSrvFileNameThe TFTP Server filename.rw DisplayString .1.3.6.1.4.1.664.5.30.3.2.3 |
adUpdtFwXfrStatusStatus of the current transfer.ro DisplayString .1.3.6.1.4.1.664.5.30.3.2.4 |
adUpdtFwXfrModuleThe module (slot) to update with the Firmware transfer.rw Integer32 .1.3.6.1.4.1.664.5.30.3.2.5 |
adUpdtFwXfrControlStart the current firmware transfer by setting value to 1 and stop a transfer in progress by setting value to 0.rw Enumeration .1.3.6.1.4.1.664.5.30.3.2.6 |
adXferConfig OBJECT IDENTIFIER .1.3.6.1.4.1.664.5.30.3.3 |
adUnitXferConfigMethodMethod to download/upload the unit's configuration.rw Enumeration .1.3.6.1.4.1.664.5.30.3.3.1 |
adUnitXferConfigTypeFormat of the configuration file.rw Enumeration .1.3.6.1.4.1.664.5.30.3.3.2 |
adUnitConfigTFTPSrvAddrHostname or IP address of the TFTP server.rw DisplayString .1.3.6.1.4.1.664.5.30.3.3.3 |
adUnitConfigTFTPSrvFileNameThe filename to download/upload from the TFTP server.rw DisplayString .1.3.6.1.4.1.664.5.30.3.3.4 |
adUnitConfigCurrXfrStatusThe status of the current configuration file transfer.ro AdTftpConfigXferStatus .1.3.6.1.4.1.664.5.30.3.3.5 |
adUnitConfigPrevXfrStatusThe status of the previous the configuration file transfer.ro AdTftpConfigXferStatus .1.3.6.1.4.1.664.5.30.3.3.6 |
adUpdtConfigXfrModuleIf 0 through 35 is selected, the source or destination module (slot) for the configuration transfer. If -1 is selected the entire configuration is transfered.rw Integer32 (-1..35) -- MAX?? .1.3.6.1.4.1.664.5.30.3.3.7 |
adUnitXferConfigSet value to 1 to transfer the configuration file from the tftp server and switch to the configuration. Set value to 2 to transfer the configuration file to the tftp server.rw Enumeration .1.3.6.1.4.1.664.5.30.3.3.8 |
adUnitCpuUtil OBJECT IDENTIFIER .1.3.6.1.4.1.664.5.30.3.4 |
adUnitCurrentCpuUtilAverage CPU utilization over the last second.ro Gauge32 .1.3.6.1.4.1.664.5.30.3.4.1 |
adUnitTotalCpuUtilAverage CPU utilization since last system reboot or statistics reset.ro Gauge32 .1.3.6.1.4.1.664.5.30.3.4.2 |
adUnitClearUtilizationStatsSet value to 1 to clear CPU utilization statistics.rw Integer32 (1) .1.3.6.1.4.1.664.5.30.3.4.3 |
adUnitPing OBJECT IDENTIFIER .1.3.6.1.4.1.664.5.30.3.5 |
adUnitPingStatusSet value to 1 to Stop ping sequence and 2 to start ping sequence.rw Enumeration .1.3.6.1.4.1.664.5.30.3.5.1 |
adUnitPingModeSet the 'sweep' BIT to cause the ping process to send consecutively increasing buffer sizes starting at adUnitPingPktMinSize and continueing to adUnitPingPktMaxSize. If 'sweep' is not set, a single packet size of adUnitPingPktMinSize is used. The default is for sweep to not be set. Set the 'verbose' bit for responses to be reported via entries in the adUnitPingRespTbl. If 'verbose' is not set, results are reported via adUnitPingResult. The default is for verbose to not be set.rw Bits .1.3.6.1.4.1.664.5.30.3.5.2 |
adUnitPingTargetHost name or IP Address of the unit to ping.rw DisplayString .1.3.6.1.4.1.664.5.30.3.5.3 |
adUnitPingPktMinSizeIf in normal mode specifies the size of the ping request buffer. In Sweep mode the mininum initial size.rw Integer32 .1.3.6.1.4.1.664.5.30.3.5.4 |
adUnitPingPktMaxSizeNot used in normal mode. In Sweep mode, the maximum buffer size used for the sweep. If the value is not greater than adUnitPingPktMinSize the sweep will terminate after the first buffer size completes.rw Integer32 .1.3.6.1.4.1.664.5.30.3.5.5 |
adUnitPingFillBufferSpecify the characters to replicate within the outgoing request buffer.rw OCTET STRING .1.3.6.1.4.1.664.5.30.3.5.6 |
adUnitPingSourceThe IP Address to be inserted into source field of transmitted message. If set to the default of 0.0.0.0, the address of the source network interface ( determined from the route table) is used.rw IpAddress .1.3.6.1.4.1.664.5.30.3.5.7 |
adUnitPingTimeoutSpecify the Timeout for each ping request, specified in seconds.rw Integer32 .1.3.6.1.4.1.664.5.30.3.5.8 |
adUnitPingRepeatCntSpecify the number of times to repeat the ping request. For verbose mode maximum allowed is 50, for normal mode, the maximum is 255.rw Integer32 .1.3.6.1.4.1.664.5.30.3.5.9 |
adUnitPingXmtNumThe actual number of ping requests transmitted.ro Integer32 .1.3.6.1.4.1.664.5.30.3.5.10 |
adUnitPingRcvNumThe number of respsones receivedro Integer32 .1.3.6.1.4.1.664.5.30.3.5.11 |
adUnitPingResultOutput string to show results of ping when in normal mode. If more than 255 transmissions are generated during the ping execution only the results of the first 255 are reported. The following characters indicate the specified results: ! OK . Timeout, no response U Destination Unreachable Q Source Quench (destination too busy) M Could not fragment ? Unknown Packet type & Packet lifetime exceededrw DisplayString .1.3.6.1.4.1.664.5.30.3.5.12 |
adUnitPingMinRndTrpThe minimum round-trip time in milliseconds.ro Integer32 .1.3.6.1.4.1.664.5.30.3.5.13 |
adUnitPingMaxRndTrpThe maximum round-trip time in milliseconds.ro Integer32 .1.3.6.1.4.1.664.5.30.3.5.14 |
adUnitPingAvgRndTrpThe average round-trip time in milliseconds.ro Integer32 .1.3.6.1.4.1.664.5.30.3.5.15 |
adUnitPingVerboseTableA table reporting the verbose output of the last ping test initiated via SNMP. SEQUENCE OF AdUnitPingVerboseEntry .1.3.6.1.4.1.664.5.30.3.5.16 |
adUnitPingVerboseEntryEach entry in the list is the result of a single ping request. Each request is identified by its sequence number, adPingRespIndex. AdUnitPingVerboseEntry .1.3.6.1.4.1.664.5.30.3.5.16.1 |
adPingRespIndexThe ping response sequence number. Integer32 .1.3.6.1.4.1.664.5.30.3.5.16.1.1 |
adPingRespStatusThe compeletion status of the ping response: 1 - OK 2 - Target address is unknown 3 - Invalid Source address 4 - No response received before timeout expired 5 - Unreachable destination (adPingRespAddr contains reporting address) 6 - TTL expired in transit (adPingRespAddr contains reporting address)ro Enumeration .1.3.6.1.4.1.664.5.30.3.5.16.1.2 |
adPingRespAddrThe reply from address.ro IpAddress .1.3.6.1.4.1.664.5.30.3.5.16.1.3 |
adPingRespSizeBuffer Size of the response.ro Integer32 .1.3.6.1.4.1.664.5.30.3.5.16.1.4 |
adPingRespTimeTime in milliseconds to receive response.ro Integer32 UNITS "milliseconds" .1.3.6.1.4.1.664.5.30.3.5.16.1.5 |
adPingRespTTLTTL value of the response. For TTL to be reported, the buffer size of the request (adUnitPingPktSize) must be at least 4 bytes.ro Integer32 .1.3.6.1.4.1.664.5.30.3.5.16.1.6 |
adUnitTraceRt OBJECT IDENTIFIER .1.3.6.1.4.1.664.5.30.3.6 |
adUnitTraceRtStatusSet value to 0 to interrupt and stop a TraceRoute sequence and 1 to start a TraceRoute sequence. When TraceRoute completes value with change from 'active' to 'inActive'.rw Enumeration .1.3.6.1.4.1.664.5.30.3.6.1 |
adUnitTraceRtTargetHost name or IP Address of the unit to probe.rw DisplayString .1.3.6.1.4.1.664.5.30.3.6.2 |
adUnitTraceRtSourceThe IP Address to be inserted into source field of transmitted message. If set to the default of 0.0.0.0, the unit address is used.rw IpAddress .1.3.6.1.4.1.664.5.30.3.6.3 |
adUnitTraceRtTimeoutThe response timeout for all traceroute probes.rw Integer32 .1.3.6.1.4.1.664.5.30.3.6.4 |
adUnitTraceRtProbeCntThe number of probes to initiate for each TTL.rw Integer32 .1.3.6.1.4.1.664.5.30.3.6.5 |
adUnitTraceRtMinTTLThe Minimum Time To Live value (hops) of the traceroute probes.rw Integer32 .1.3.6.1.4.1.664.5.30.3.6.6 |
adUnitTraceRtMaxTTLSpecify the Maximum Time To Live value (hops) of the traceroute probes.rw Integer32 .1.3.6.1.4.1.664.5.30.3.6.7 |
adUnitTraceRtPortNumSet the base UDP port number used in probes. Traceroute operation is based on the fact that nothing is listening on UDP ports base to base + nhops - 1 at the destination host (so an ICMP PORT_UNREACHABLE message will be returned to terminate the route tracing). If something is listening on a port in the default range, this option can be used to pick an unused port range.rw Integer32 .1.3.6.1.4.1.664.5.30.3.6.8 |
adUnitTraceRtRespTableA table reporting the output of each traceroute probe initiated via SNMP. Upon initiation of a traceroute any existing entries in the table are automatically deleted by the agent & new records are inserted to reflect the results of the most recent traceroute test. SEQUENCE OF AdUnitTraceRtRespEntry .1.3.6.1.4.1.664.5.30.3.6.9 |
adUnitTraceRtRespEntryEach entry in the list is the result of a single probe request intiated by traceroute. Each request is identified by its TTL number, adTraceRtRespIndex. When a trace route is started all entries are deleted from the table and then inserted as the result of each attempt is determined AdUnitTraceRtRespEntry .1.3.6.1.4.1.664.5.30.3.6.9.1 |
adTraceRtRespIndexThe traceroute response sequence number (TTL). Integer32 .1.3.6.1.4.1.664.5.30.3.6.9.1.1 |
adTraceRtRespStringThe response output from the traceroute process for each probe.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.5.30.3.6.9.1.2 |
adUnitStatus OBJECT IDENTIFIER .1.3.6.1.4.1.664.5.30.4 |
adUnitFaceplateA bit encoded string representing the status of all faceplate indicators, LEDs, & switches for GUI visualization of the unit. Each product defines this as a bitmap of booleans, or a byte for each indicator if not binary. The strings from all the slots are concatenated into this one object, after prefixing each card indicator string with two bytes. The first byte contains the slot number as an integer, and the second byte contains the remaining string length for that slot. The Textual Convention AdDualLEDstatus should be used for non-binary states.ro OCTET STRING .1.3.6.1.4.1.664.5.30.4.1 |
adUnitAlarmStatusA bit encoded string representing a summary of the alarm state of the chassis. Refer to individual unit documentation for the specification of the bimaskro OCTET STRING .1.3.6.1.4.1.664.5.30.4.2 |
adUnitSlots OBJECT IDENTIFIER .1.3.6.1.4.1.664.5.30.5 |
adUnitSlotInfoTableTable of slots available for boards. SEQUENCE OF AdUnitSlotInfoEntry .1.3.6.1.4.1.664.5.30.5.1 |
adUnitSlotInfoEntryGeneral information descibing the contents of each card slot. AdUnitSlotInfoEntry .1.3.6.1.4.1.664.5.30.5.1.1 |
adUnitSlotInfoIndexA unique value for each slot. Its value may exceed the value of adUnitSlotNumber if pseudo slot numbers are used for some bank commons or multiplexers. Integer32 .1.3.6.1.4.1.664.5.30.5.1.1.1 |
adUnitSlotProdNameThe Adtran Product Name.ro DisplayString .1.3.6.1.4.1.664.5.30.5.1.1.2 |
adUnitSlotProdPartNumberThe Adtran Product Part Number.ro DisplayString .1.3.6.1.4.1.664.5.30.5.1.1.3 |
adUnitSlotProdCLEIcodeThe Adtran Product CLEI Code.ro DisplayString .1.3.6.1.4.1.664.5.30.5.1.1.4 |
adUnitSlotProdSerialNumberThe Adtran Product Serial Number.ro DisplayString .1.3.6.1.4.1.664.5.30.5.1.1.5 |
adUnitSlotProdRevisionThe Adtran Product Revision Number.ro DisplayString .1.3.6.1.4.1.664.5.30.5.1.1.6 |
adUnitSlotProdSwVersionThe Adtran Product Software Version Number.ro DisplayString .1.3.6.1.4.1.664.5.30.5.1.1.7 |
adUnitSlotProdPhysAddressThis octet string variable contains the Adtran Physical Address assigned to this product. For example the octet sequence, 16 02 03 01, specifies channel bank number 16, digroup number 2, DS0 channel slot number 3, position 1. This object value is commonly reported in SNMP Traps to identify the product's location.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.664.5.30.5.1.1.8 |
adUnitSlotInfoStateThe state of the card slot. Initially it is empty. When a card is inserted, it becomes occupied, and the Slot Type is determined by the card Product Code. When a card is removed, it changes to virtual, and retains the SlotType characteristics until a different kind of card is inserted, or a different preconfiguration is established.ro AdPresence .1.3.6.1.4.1.664.5.30.5.1.1.9 |
adUnitSlotProductThe ADTRAN Product code, 0 if empty. Agent will report real product code when installed or pre-provisioned.ro AdProductIdentifier .1.3.6.1.4.1.664.5.30.5.1.1.10 |
adUnitSlotTrapEnableEnables/Disables traps initiated from this slot.rw Enumeration .1.3.6.1.4.1.664.5.30.5.1.1.11 |
adUnitSlotAlarmStatusA bit encoded string representing the alarm state of the slot. The LSB should be 1 for No Alarm, else 0 and the higher order bits will indicate which alarms are present. The specific alarm conditions may be found in more specific generic MIBs or in the device MIB.ro OCTET STRING .1.3.6.1.4.1.664.5.30.5.1.1.12 |
adUnitSlotFaceplateA bit encoded string representing the status of faceplate indicators, LEDs, & switches for GUI visualization associated with the card in the respective slot. Each product defines this as a bitmap of booleans, or a byte for each indicator if not binary. The Textual Convention AdDualLEDstatus should be used for non-binary states.ro OCTET STRING .1.3.6.1.4.1.664.5.30.5.1.1.13 |
adUnitSlotServiceStateModule service state. The full enumeration is supported by CND products. END products may support only the following subset with the END equivalent state following '/': is -- InService / Online oosUas -- Out of Service, Unasssigned / Unavailable oosMA -- Out of Sevice, Maint. / Offlinerw Enumeration .1.3.6.1.4.1.664.5.30.5.1.1.14 |
adUnitPort OBJECT IDENTIFIER .1.3.6.1.4.1.664.5.30.6 |
adUnitPortInfoTableA table of hardware oriented port information on each card. This only includes actual card ports, and not layered logical interfaces. SEQUENCE OF AdUnitPortInfoEntry .1.3.6.1.4.1.664.5.30.6.3 |
adUnitPortInfoEntryA row table entry exists for each card/port pair. AdUnitPortInfoEntry .1.3.6.1.4.1.664.5.30.6.3.1 |
adUnitPortInfoIndexA unique value for each physical port on a card. Integer32 .1.3.6.1.4.1.664.5.30.6.3.1.1 |
adUnitPortInfoStateThe state of the card port. Initially it is empty.ro AdPresence .1.3.6.1.4.1.664.5.30.6.3.1.2 |
adUnitPortIfIndexThe interface number identified as ifIndex from the MIB-II interfaces table as defined by the slot and port numbers in this device.ro Integer32 .1.3.6.1.4.1.664.5.30.6.3.1.3 |
adUnitPortAlarmStatusA bit encoded string representing the alarm state of the port.ro OCTET STRING .1.3.6.1.4.1.664.5.30.6.3.1.4 |
adUnitPortDescriptionA character string to identify the name of a port. Used for trap varbind in last trap sent. Should default to port number string. Can be overridden by customer as desired.rw DisplayString .1.3.6.1.4.1.664.5.30.6.3.1.5 |
adUnitPortSlotMapTableTable to map ifIndex to slot, port & type. SEQUENCE OF AdUnitPortSlotMapEntry .1.3.6.1.4.1.664.5.30.6.4 |
adUnitPortSlotMapEntryAn entry exists for each interface which is mapped to a physical slot/port pair. AdUnitPortSlotMapEntry .1.3.6.1.4.1.664.5.30.6.4.1 |
adUnitSlotAddressThe slot in which this port is contained. Slot 0 is reported for the unit controller and all logical interfaces.ro Integer32 .1.3.6.1.4.1.664.5.30.6.4.1.1 |
adUnitPortAddressThe port number within the slot. Logical interfaces should indicate port 0.ro Integer32 .1.3.6.1.4.1.664.5.30.6.4.1.2 |
adUnitConformance OBJECT IDENTIFIER .1.3.6.1.4.1.664.5.30.7 |
adUnitCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.664.5.30.7.1 |
adUnitComplianceThe compliance statement for SNMPv2 entities which implement the adUnit MIB. Unknown .1.3.6.1.4.1.664.5.30.7.1.1 |
adUnitMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.664.5.30.7.2 |
adUnitBaseGroupThe Unit Base Group. Unknown .1.3.6.1.4.1.664.5.30.7.2.1 |
adUnitUserGroupThe Unit Telnet Group. Unknown .1.3.6.1.4.1.664.5.30.7.2.2 |
adUnitSNMPConfigGroupThe Unit SNMP Config Group. Unknown .1.3.6.1.4.1.664.5.30.7.2.3 |
adUnitMaintConsoleGroupThe Unit Maintenance Console Group. Unknown .1.3.6.1.4.1.664.5.30.7.2.4 |
adUnitSyslogGroupThe Unit Syslog Client Group. Unknown .1.3.6.1.4.1.664.5.30.7.2.5 |
adUnitTFTPGroupThe Unit TFTP Group. Unknown .1.3.6.1.4.1.664.5.30.7.2.6 |
adUnitCpuUtilGroupThe Unit CPU Utilization Group. Unknown .1.3.6.1.4.1.664.5.30.7.2.7 |
adUnitPingGroupThe Unit Ping Group. Unknown .1.3.6.1.4.1.664.5.30.7.2.8 |
adUnitTraceRtGroupThe Traceroute Group. Unknown .1.3.6.1.4.1.664.5.30.7.2.9 |
adUnitSlotGroupThe Unit Slot Group. Unknown .1.3.6.1.4.1.664.5.30.7.2.10 |
adUnitPortGroupThe Unit Slot Group. Unknown .1.3.6.1.4.1.664.5.30.7.2.11 |
adUnitsCndGroupThe CND Management Group. Support for this group is only required when the unit is to be managed in a CND environment. For instance, IADs which are remotely provisioned by a service provider via Total Access EMS. Unknown .1.3.6.1.4.1.664.5.30.7.2.12 |
adUnitsExtendedBaseGroupThe Extended Base Group containing functions not supported by all units. Unknown .1.3.6.1.4.1.664.5.30.7.2.13 |
adUnitsExtendedSNMPGroupThe Extended SNMP Group containing functions not supported by all units. Unknown .1.3.6.1.4.1.664.5.30.7.2.14 |
adConsoleModemGroupThe Console Modem Group containing functions not supported by all units. Unknown .1.3.6.1.4.1.664.5.30.7.2.15 |
adUnitsExtendedSyslogGroupThe Extended Syslog Group containing functions not supported by all units. Unknown .1.3.6.1.4.1.664.5.30.7.2.16 |
adUnitExtendedPingGroupThe Unit Ping Group supporting extended Ping operations (for instance, sweep & verbose modes). Unknown .1.3.6.1.4.1.664.5.30.7.2.17 |