ADTRAN-DSUIQ-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for ADTRAN-DSUIQ-MIB.
189
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
189 total| Object Name |
|---|
adDSUIQ OBJECT IDENTIFIER .1.3.6.1.4.1.664.1.141 |
RFC1155-SMI Unknown .1.3.6.1.4.1.664.1.141 |
adDSUIQNetworkPhysUpThis trap indicates that the physical
layer of the network is now up. TRAP-TYPE .1.3.6.1.4.1.664.1.141.0.14101 |
adDSUIQNetworkPhysDownThis trap indicates that the physical
layer of the network is now down. TRAP-TYPE .1.3.6.1.4.1.664.1.141.0.14102 |
adDSUIQNetworkLMIUpThis trap indicates that the LMI state
of the network is now up. TRAP-TYPE .1.3.6.1.4.1.664.1.141.0.14103 |
adDSUIQNetworkLMIDownThis trap indicates that the LMI state
of the network is now down. TRAP-TYPE .1.3.6.1.4.1.664.1.141.0.14104 |
adDSUIQColdStartThis trap indicates that a cold start has occurred. TRAP-TYPE .1.3.6.1.4.1.664.1.141.0.14105 |
adDSUIQmg OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.141 |
adDSUIQSystemConfig OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.141.1 |
adDSUIQPasswordSets the Telnet and Vt100 Terminal Control Password (10 characters maximum).rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.141.1.1 |
adDSUIQTODSets the Time of Day with the format hh:mm.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.141.1.2 |
adDSUIQDateSets the Date with format MM-DD-YY.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.141.1.3 |
adDSUIQIpAddressSets the unit's IP Address.rw IpAddress .1.3.6.1.4.1.664.2.141.1.4 |
adDSUIQIpAddressMaskSets the unit's Subnet Mask.rw IpAddress .1.3.6.1.4.1.664.2.141.1.5 |
adDSUIQGatewayIpAddressSets the Network's Gateway IP Address.rw IpAddress .1.3.6.1.4.1.664.2.141.1.6 |
adDSUIQTrapManagerIpAddressSets the IP Address of the Trap Host Manager.rw IpAddress .1.3.6.1.4.1.664.2.141.1.7 |
adDSUIQTrapManagerDLCISets the DLCI of the Trap Host Manager. (Range 16 - 1007).rw INTEGER .1.3.6.1.4.1.664.2.141.1.8 |
adDSUIQTrapManagerPortSelects the Trap Manager Port.rw Enumeration .1.3.6.1.4.1.664.2.141.1.9 |
adDSUIQControPortBaudSelects the Control Port baud rate.rw Enumeration .1.3.6.1.4.1.664.2.141.1.10 |
adDSUIQControPortModeSelects the Control Port protocol.rw Enumeration .1.3.6.1.4.1.664.2.141.1.11 |
adDSUIQEnableTrapsOverall trap enable/disable.rw Enumeration .1.3.6.1.4.1.664.2.141.1.12 |
adDSUIQAlarmStateThis bit map variable indicates alarm conditions which
are currently set. When an alarm condition occurs, the
corresponding event bit is set in this variable. If
armed, setting the event will generate an Alarm Trap.
The various alarm event bit positions are:
1 = Network physical link up.
2 = Network physical link down.
4 = Network signal state up.
8 = Network signal state down.ro INTEGER .1.3.6.1.4.1.664.2.141.1.13 |
adDSUIQArmAlarmThis bit map variable arms or disarms an individual or
group of events identified in adFradAlarmState as a source
for generation of an Alarm Trap.
The various arm event bit positions are :
1 = Network physical link up.
2 = Network physical link down.
4 = Network signal state up.
8 = Network signal state down.rw INTEGER .1.3.6.1.4.1.664.2.141.1.14 |
adDSUIQAbortConfigA Set will cancel the current selections and revert to the last Saved configuration.rw Enumeration .1.3.6.1.4.1.664.2.141.1.15 |
adDSUIQSaveConfigA Set operation will reset the unit and save current selections.rw Enumeration .1.3.6.1.4.1.664.2.141.1.16 |
adDSUIQNetPortConfig OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.141.2 |
adDSUIQNetPortLoopRateSelects the Rate for the DDS interface.rw Enumeration .1.3.6.1.4.1.664.2.141.2.1 |
adDSUIQNetPortClockSourceSelects the Timing source for the DDS interface.rw Enumeration .1.3.6.1.4.1.664.2.141.2.2 |
adDSUIQNetPortSignalingSignaling type for the frame relay management interface.rw Enumeration .1.3.6.1.4.1.664.2.141.2.3 |
adDSUIQNetPortt391Sets the polling interval in seconds for the frame relay management interface.
(Range 5 - 30).rw INTEGER .1.3.6.1.4.1.664.2.141.2.4 |
adDSUIQNetPortn391Sets the interval between full status polls for the frame relay management
interface. (Range 1 - 255).rw INTEGER .1.3.6.1.4.1.664.2.141.2.5 |
adDSUIQNetPortn392Sets the error count for the frame relay management interface. (Range 1 - 10).rw INTEGER .1.3.6.1.4.1.664.2.141.2.6 |
adDSUIQNetPortn393Sets the error window (number of polling events)for the frame relay management
interface. (Range 1 - 10).rw INTEGER .1.3.6.1.4.1.664.2.141.2.7 |
adDSUIQNetPortMgmtDlci1ModeSets the mode for the managent DLCI 1. If set for shared, management DLCI 1 is used for customer data and
IQ management data. If set for dedicated, management DLCI 1 is used only for IQ management data and is
not passed to the attached frame relay DTE device.rw Enumeration .1.3.6.1.4.1.664.2.141.2.8 |
adDSUIQNetPortMgmtDlci2ModeSets the mode for the managent DLCI 2. If set for shared, management DLCI 2 is used for customer data and
IQ management data. If set for dedicated, management DLCI 2 is used only for IQ management data and is
not passed to the attached frame relay DTE device.rw Enumeration .1.3.6.1.4.1.664.2.141.2.9 |
adDSUIQNetMgmtDlci1Sets the DLCI for management PVC 1. (Range 16 - 1007).rw INTEGER .1.3.6.1.4.1.664.2.141.2.10 |
adDSUIQNetMgmtDlci2Sets the DLCI for management PVC 2. (Range 16 - 1007).rw INTEGER .1.3.6.1.4.1.664.2.141.2.11 |
adDSUIQNetPortMaxPVCsSets the maxium PVCs supported by the IQ unit. (Range 1 - 100).rw INTEGER .1.3.6.1.4.1.664.2.141.2.12 |
adDSUIQNetPortHistIntervalsSets the number of history intervals for storage.rw INTEGER .1.3.6.1.4.1.664.2.141.2.13 |
adDSUIQNetPortHistIntervalsAvailableReturns the number of history intervals allowed based on the maxium number of PVCs selected.ro INTEGER .1.3.6.1.4.1.664.2.141.2.14 |
adDSUIQDtePortConfig OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.141.3 |
adDSUIQDtePortInterfaceSelects the DTE Port Interface type.rw Enumeration .1.3.6.1.4.1.664.2.141.3.1 |
adDSUIQDtePortRateSelects the DTE Port Rate.rw Enumeration .1.3.6.1.4.1.664.2.141.3.2 |
adDSUIQDteCTSOptionSelects the Clear to Send (CTS) option.rw Enumeration .1.3.6.1.4.1.664.2.141.3.3 |
adDSUIQDteCDOptionSelects the Carrier Detect (CD) option.rw Enumeration .1.3.6.1.4.1.664.2.141.3.4 |
adDSUIQDteDSROptionSelects the Data Set Ready (DSR) option.rw Enumeration .1.3.6.1.4.1.664.2.141.3.5 |
adDSUIQDtePortMgmtDLCISets the DTE Port Management DLCI. (Range 16 - 1007).rw INTEGER .1.3.6.1.4.1.664.2.141.3.6 |
adDSUIQDtePortt392Sets the timeout in seconds between polling intervals. (Range 5 - 30).rw INTEGER .1.3.6.1.4.1.664.2.141.3.7 |
adDSUIQDtePortn392Sets the number of error events for the frame relay management.
(Range 1 - 10).rw INTEGER .1.3.6.1.4.1.664.2.141.3.8 |
adDSUIQDtePortn393Sets the error window (polling events) for the frame relay management
(Range 1 - 10).rw INTEGER .1.3.6.1.4.1.664.2.141.3.9 |
adDSUIQDteManagementPvcOptionControls the presence of the DTE management PVC in a full status response to the DTE device.rw Enumeration .1.3.6.1.4.1.664.2.141.3.10 |
adDSUIQDteSignalingResponsesOptionDetermines how the IQ device will respond to polls from the DTE device during a network failure.
If set to always on, the IQ will respond to polls during a network failure. If set to follow network, the IQ
will not respond thus emulating a failure to the DTE device. If the IQ is responsible for
dial backup, this option should be set to always on.rw Enumeration .1.3.6.1.4.1.664.2.141.3.11 |
adDSUIQDteFlowControlOptionDetermines how the IQ device will respond to congestion during DBU operation.
If set for none, the IQ will drop frames during DBU operation when severe congestion occurs.
If set for hardware, the IQ will vary the DTE TC clock in order to control the amount of data
offered to the IQ when severe congestion occurs. FECN/BECN mode will set the FECN bit in outbound frames
and set BECN bit for inbound frames leaving flow control up to the DTE devices.rw Enumeration .1.3.6.1.4.1.664.2.141.3.12 |
adDSUIQPvcConfig OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.141.4 |
adDSUIQPvcConfigTablen/a. SEQUENCE OF AdDSUIQPvcConfigEntry .1.3.6.1.4.1.664.2.141.4.1 |
adDSUIQPvcConfigEntryn/a AdDSUIQPvcConfigEntry .1.3.6.1.4.1.664.2.141.4.1.1 |
adDSUIQPvcConfigIndexn/a.ro INTEGER .1.3.6.1.4.1.664.2.141.4.1.1.1 |
adDSUIQPvcDLCIAddress for this PVC entry. (Range 16 - 1007).rw INTEGER .1.3.6.1.4.1.664.2.141.4.1.1.2 |
adDSUIQPvcCIRCommited Information Rate for this PVC in Kbps.rw INTEGER .1.3.6.1.4.1.664.2.141.4.1.1.3 |
adDSUIQPvcSequenceOptionSequence number allows the IQ to detect lost frames across the frame relay
service. This option should be disabled for PVCs that do not have IQ
on both ends.rw Enumeration .1.3.6.1.4.1.664.2.141.4.1.1.4 |
adDSUIQPvcDelayPacketOptionDelay packet option for this PVC allows the IQ to sample round trip delay
across the frame relay service. This option should be disabled for PVCs that do not have IQ
on both ends.rw Enumeration .1.3.6.1.4.1.664.2.141.4.1.1.5 |
adDSUIQPvcDBUDLCIUsed when this PVC entry is used for dial backup. This value should contain the PVC address
as seen on the far end of the PVC.rw INTEGER .1.3.6.1.4.1.664.2.141.4.1.1.6 |
adDSUIQPvcStatsControlStats Control option determines how the IQ will track statistics for this PVC entry. Auto will
allow the IQ to track statistics for a PVC if enough memory is available.rw Enumeration .1.3.6.1.4.1.664.2.141.4.1.1.7 |
adDSUIQCurrentStatus OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.141.5 |
adDSUIQDDSStateCurrent status of the DDS interfacero Enumeration .1.3.6.1.4.1.664.2.141.5.1 |
adDSUIQDteControlLeadsThis bit map integer reflects the current state of the DTE control leads as follows:
bit meaning
0 CTS
1 RTS
2 DSR
3 DTR
4 DCD
A 1 means the lead is on.ro INTEGER .1.3.6.1.4.1.664.2.141.5.2 |
adDSUIQDBUPortTypeReturns the DBU card type installed.ro Enumeration .1.3.6.1.4.1.664.2.141.5.3 |
adDSUIQLANPortStatusReturns the LAN card type installed.ro Enumeration .1.3.6.1.4.1.664.2.141.5.4 |
adDSUIQLEDstatusThis bit map integer reflects DSUIQ front panel LED state as follows:
bit meaning
0 TEST
1 ALARM
2 DCD
3 RD
4 TD
5 CTS
6 RTSro INTEGER .1.3.6.1.4.1.664.2.141.5.5 |
adDSUIQDTESignalingStateCurrent state of the PVC signaling between the DSUIQ and the attached frame relay dte.ro Enumeration .1.3.6.1.4.1.664.2.141.5.6 |
adDSUIQNETSignalingStateCurrent state of the PVC signaling between the DSUIQ and the frame relay service.ro Enumeration .1.3.6.1.4.1.664.2.141.5.7 |
adDSUIQNETPVCCountCurrent count of network pvcs.ro INTEGER .1.3.6.1.4.1.664.2.141.5.8 |
adDSUIQNETPVCConfigTableSizeCurrent count of rows in the PVC config table.ro INTEGER .1.3.6.1.4.1.664.2.141.5.9 |
adDSUIQDBUStateCurrent state of the DBU interface.ro Enumeration .1.3.6.1.4.1.664.2.141.5.10 |
adDSUIQIntDDSStatus OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.141.6 |
adDSUIQIntDDSStatusTablen/a. SEQUENCE OF AdDSUIQIntDDSStatusEntry .1.3.6.1.4.1.664.2.141.6.1 |
adDSUIQIntDDSStatusEntryn/a AdDSUIQIntDDSStatusEntry .1.3.6.1.4.1.664.2.141.6.1.1 |
adDSUIQIntDDSSlotIndexn/a.ro INTEGER .1.3.6.1.4.1.664.2.141.6.1.1.1 |
adDSUIQIntDDSUnavailableTimeAmount of time in seconds the DDS port is unavailable due to test
or in an inactive state.ro Counter .1.3.6.1.4.1.664.2.141.6.1.1.2 |
adDSUIQIntDDSStateChangeNumber of changes in the DDS port state. This includes all normal, inactive, and test
state transitions.ro Counter .1.3.6.1.4.1.664.2.141.6.1.1.3 |
adDSUIQIntDDSBPVFrameErrorNumber of BPVs received when the DDS is set for 56K mode or the number of
DDS framing errors when the DDS is set for 64K mode.ro Counter .1.3.6.1.4.1.664.2.141.6.1.1.4 |
adDSUIQDayDDSStatus OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.141.7 |
adDSUIQDayDDSStatusTablen/a. SEQUENCE OF AdDSUIQDayDDSStatusEntry .1.3.6.1.4.1.664.2.141.7.1 |
adDSUIQDayDDSStatusEntryn/a AdDSUIQDayDDSStatusEntry .1.3.6.1.4.1.664.2.141.7.1.1 |
adDSUIQDayDDSSlotIndexn/a.ro INTEGER .1.3.6.1.4.1.664.2.141.7.1.1.1 |
adDSUIQDayDDSUnavailableTimeAmount of time in seconds the DDS port is unavailable due to test
or in an inactive state.ro Counter .1.3.6.1.4.1.664.2.141.7.1.1.2 |
adDSUIQDayDDSStateChangeNumber of changes in the DDS port state. This includes all normal, inactive, and test
state transitions.ro Counter .1.3.6.1.4.1.664.2.141.7.1.1.3 |
adDSUIQDayDDSBPVFrameErrorNumber of BPVs received when the DDS is set for 56K mode or the number of
DDS framing errors when the DDS is set for 64K mode.ro Counter .1.3.6.1.4.1.664.2.141.7.1.1.4 |
adDSUIQDiagnostic OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.141.8 |
adDSUIQDiagnosticTablen/a. SEQUENCE OF AdDSUIQDiagnosticEntry .1.3.6.1.4.1.664.2.141.8.1 |
adDSUIQDiagnosticEntryn/a AdDSUIQDiagnosticEntry .1.3.6.1.4.1.664.2.141.8.1.1 |
adDSUIQDiagnosticIndexn/a.ro INTEGER .1.3.6.1.4.1.664.2.141.8.1.1.1 |
adDSUIQDiagnosticDlciSets the DLCI for PVC Loopback. (Range 16 - 1007).ro INTEGER .1.3.6.1.4.1.664.2.141.8.1.1.2 |
adDSUIQDiagnosticControlStarts or Stops PVC Loopback Test.rw Enumeration .1.3.6.1.4.1.664.2.141.8.1.1.3 |
adDSUIQDiagnosticDurationSets the Length of the PVC Loopback in minutes.rw INTEGER .1.3.6.1.4.1.664.2.141.8.1.1.4 |
adDSUIQDiagnosticStatusPVC Loopback Test Status. (Active/Inactive).rw Enumeration .1.3.6.1.4.1.664.2.141.8.1.1.5 |
adDSUIQDiagnosticSecondsRemainingPVC Loopback Test time remaining in seconds.ro INTEGER .1.3.6.1.4.1.664.2.141.8.1.1.6 |
adDSUIQDiagnosticFramesTxDiagnostic Frames transmitted.ro Counter .1.3.6.1.4.1.664.2.141.8.1.1.7 |
adDSUIQDiagnosticFramesRxDiagnostic Frames received.ro Counter .1.3.6.1.4.1.664.2.141.8.1.1.8 |
adDSUIQDiagnosticLostFramesDiagnostic Frames Lost.ro Counter .1.3.6.1.4.1.664.2.141.8.1.1.9 |
adDSUIQDiagnosticMaxDelayDiagnostic Maximum Delay measurement.ro Gauge .1.3.6.1.4.1.664.2.141.8.1.1.10 |
adDSUIQDiagnosticMinDelayDiagnostic Minimum Delay measurement.ro Gauge .1.3.6.1.4.1.664.2.141.8.1.1.11 |
adDSUIQDiagnosticAvgDelayDiagnostic Average Delay measurement.ro Gauge .1.3.6.1.4.1.664.2.141.8.1.1.12 |
adDSUIQDBUConfig OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.141.9 |
adDSUIQDBUOptionThis option specifies whether the unit automatically
enters dial backup mode or waits for manual setup.rw Enumeration .1.3.6.1.4.1.664.2.141.9.1 |
adDSUIQDBUStartLockoutThis option selects the hour to begin disabling
dial backup operation when daily or weekend
lockout mode is active.rw INTEGER .1.3.6.1.4.1.664.2.141.9.2 |
adDSUIQDBUEndLockoutThis option selects the hour to end dial backup lockout
when daily or weekend lockout mode is active.rw INTEGER .1.3.6.1.4.1.664.2.141.9.3 |
adDSUIQDBUModeThis option specifies the dial backup operating mode for the
unit as orginate or answer. One end must be set to originate
and the other end to answer.rw Enumeration .1.3.6.1.4.1.664.2.141.9.4 |
adDSUIQDBUOOSThis option enables the unit to enter backup mode if an
out-of-service condition is detected from the network.rw Enumeration .1.3.6.1.4.1.664.2.141.9.5 |
adDSUIQDBUNoRxThis option enables the unit to enter backup mode when
a loss of receive signal is detected from the network.rw Enumeration .1.3.6.1.4.1.664.2.141.9.6 |
adDSUIQDBUNoSealCurrThis option enables the unit to enter backup mode when
a loss of sealing current is detected from the network.rw Enumeration .1.3.6.1.4.1.664.2.141.9.7 |
adDSUIQDBUNoLMIThis option enables the unit to enter backup mode when
network PVC signaling state goes down.rw Enumeration .1.3.6.1.4.1.664.2.141.9.8 |
adDSUIQAutoRestoreTimerThis option selects the amount of time that the DSUIQ
circuit must be active before the unit switches from
backup to normal mode of operation. The timer value is
in minutes from 0 to 60. A zero value disables automatic
restore, DSUIQ operation must be restored manually.rw INTEGER .1.3.6.1.4.1.664.2.141.9.9 |
adDSUIQRedialCountThis option allows the selection of the number of times the
unit will redial the Far End unit when attempting to go to
backup and a busy or reorder condition occurs. Redial count
can be set for a maximum of 60.rw INTEGER .1.3.6.1.4.1.664.2.141.9.10 |
adDSUIQDBUFailTimeoutThis option allows the selection of the amount of time that
the dedicated circuit failure condition is active before
attempting to enter dial backup mode. The Fail Timeout
value is in increments of 10 seconds up to a maximum of 600 seconds.rw INTEGER .1.3.6.1.4.1.664.2.141.9.11 |
adDSUIQDBURedialTimerThis option works in conjunction with the Redial Counter option.
The Redial Timer specifies the amount of time between redial
attempts. The Redial Timer value is seconds, up to a maximum
of 60 seconds.rw INTEGER .1.3.6.1.4.1.664.2.141.9.12 |
adDSUIQDBUPassCheckThis option allows the unit to send and verify a dial backup
passcode for an additional level of security. When enabled, the
originate unit sends the passcode and the answer unit checks the
passcode before the backup connection is considered valid.rw Enumeration .1.3.6.1.4.1.664.2.141.9.13 |
adDSUIQDBUPassCodeThis option sets the dial backup passcode used to provide an
additional level of security. A passcode of one to ten digit
characters can be set. If enabled, the originate unit sends
the passcode and the answer unit checks the passcode to verify
the connection.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.141.9.14 |
adDSUIQWeekendLockoutThis option enables or disables Weekend Lockout for Dial
Backup operation. If enabled, no backup will occur from
midnight Friday to midnight Sunday.rw Enumeration .1.3.6.1.4.1.664.2.141.9.15 |
adDSUIQDailyLockoutThis option enables or disables Daily Lockout for Dial
Backup operation. If enabled, no backup will occur between
Lockout Start hour and Lockout End hour.rw Enumeration .1.3.6.1.4.1.664.2.141.9.16 |
adDSUIQAnswerAlwaysThis option enables or disables Answer Always for Dial
Backup operation. If enabled, the answer unit answers
any incoming call regardless of failed conditions.rw Enumeration .1.3.6.1.4.1.664.2.141.9.17 |
adDSUIQBeeperOptionThis option enables or disables the audible alarm
when the IQ unit goes into dial backup mode.rw Enumeration .1.3.6.1.4.1.664.2.141.9.18 |
adDSUIQDBUPhoneNumber1This option is used to set a phone number to place a DBU call.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.141.9.19 |
adDSUIQDBUPhoneNumber2This option is used to set a phone number to place a DBU call.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.141.9.20 |
adDSUIQDBUPhoneNumber3This option is used to set a phone number to place a DBU call.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.141.9.21 |
adDSUIQDBUPhoneNumber4This option is used to set a phone number to place a DBU call.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.141.9.22 |
adDSUIQDBUPhoneNumber5This option is used to set a phone number to place a DBU call.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.141.9.23 |
adDSUIQDBUISDNSwitchThis option is used to select the ISDN switch type.rw Enumeration .1.3.6.1.4.1.664.2.141.9.24 |
adDSUIQDBUISDNBChannelRateThis option is used to select the ISDN channel rate.rw Enumeration .1.3.6.1.4.1.664.2.141.9.25 |
adDSUIQDBUISDNSPIDThis option is used to set the SPID for the ISDN interface.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.141.9.26 |
adDSUIQDBUISDNLDNThis option is used to set LDN for the ISDN interface.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.141.9.27 |
adDSUIQV34LineTypeThis option selects the type of analog phone line.rw Enumeration .1.3.6.1.4.1.664.2.141.9.28 |
adDSUIQDCEInterfaceTypeThis option enables or disables Answer Always for Dial
Backup operation. If enabled, the answer unit answers
any incoming call regardless of failed conditions.rw Enumeration .1.3.6.1.4.1.664.2.141.9.29 |
adDSUIQDCEBitRateThis option is uses for utilization measurement of the DBU port when
an external DCE device is used. Set this parameter in KBPS close to the
connection rate.rw INTEGER .1.3.6.1.4.1.664.2.141.9.30 |
adDSUIQIntDBUStatus OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.141.10 |
adDSUIQIntDBUStatusTablen/a. SEQUENCE OF AdDSUIQIntDBUStatusEntry .1.3.6.1.4.1.664.2.141.10.1 |
adDSUIQIntDBUStatusEntryn/a AdDSUIQIntDBUStatusEntry .1.3.6.1.4.1.664.2.141.10.1.1 |
adDSUIQIntDBUSlotIndexn/a.ro INTEGER .1.3.6.1.4.1.664.2.141.10.1.1.1 |
adDSUIQIntDBUFramesRxThe number of Frames the Port received for the interval.ro Counter .1.3.6.1.4.1.664.2.141.10.1.1.2 |
adDSUIQIntDBUFramesTxThe number of Frames the Port transmitted for the interval.ro Counter .1.3.6.1.4.1.664.2.141.10.1.1.3 |
adDSUIQIntDBUBytesRxThe number of Bytes the Port received for the interval.ro Counter .1.3.6.1.4.1.664.2.141.10.1.1.4 |
adDSUIQIntDBUBytesTxThe number of Bytes the Port transmitted for the interval.ro Counter .1.3.6.1.4.1.664.2.141.10.1.1.5 |
adDSUIQIntDBUAvgThruputTxThe Average Throughput the Port transmitted for the interval.ro Gauge .1.3.6.1.4.1.664.2.141.10.1.1.6 |
adDSUIQIntDBUAvgThruputRxThe Average Throughput the Port received for the interval.ro Gauge .1.3.6.1.4.1.664.2.141.10.1.1.7 |
adDSUIQIntDBUMaxThruputTxThe Maximum Throughput the Port transmitted for the interval.ro Counter .1.3.6.1.4.1.664.2.141.10.1.1.8 |
adDSUIQIntDBUMaxThruputRxThe Maximum Throughput the Port received for the interval.ro Counter .1.3.6.1.4.1.664.2.141.10.1.1.9 |
adDSUIQIntDBUAvgUtilizationTxThe Average Utilization the Port transmitted for the interval.ro Gauge .1.3.6.1.4.1.664.2.141.10.1.1.10 |
adDSUIQIntDBUAvgUtilizationRxThe Average Utilization the Port received for the interval.ro Gauge .1.3.6.1.4.1.664.2.141.10.1.1.11 |
adDSUIQIntDBUMaxUtilizationTxThe Maximum Utilization the Port transmitted for the interval.ro Counter .1.3.6.1.4.1.664.2.141.10.1.1.12 |
adDSUIQIntDBUMaxUtilizationRxThe Maximum Utilization the Port received for the interval.ro Counter .1.3.6.1.4.1.664.2.141.10.1.1.13 |
adDSUIQIntTimeInDBUTime in seconds the DBU port was active.ro Counter .1.3.6.1.4.1.664.2.141.10.1.1.14 |
adDSUIQIntDBUCrcErrorsNumber of frames received with CRC errors.ro Counter .1.3.6.1.4.1.664.2.141.10.1.1.15 |
adDSUIQIntDBUAbortFramesNumber of frames received without proper flag termination.ro Counter .1.3.6.1.4.1.664.2.141.10.1.1.16 |
adDSUIQIntDBUOctectViolationsNumber of frames received with a bit count not divisible by eigth.ro Counter .1.3.6.1.4.1.664.2.141.10.1.1.17 |
adDSUIQIntDBUDiscardFramesNumber of frames discarded by the IQ unitro Counter .1.3.6.1.4.1.664.2.141.10.1.1.18 |
adDSUIQIntDBULengthErrorsNumber of frames received that is less than 5 bytes or greater than 4500 bytes.ro Counter .1.3.6.1.4.1.664.2.141.10.1.1.19 |
adDSUIQIntDBUEncapsulationErrorsNumber of frames destined for the IQ IP stack with that does not meet
the FRF.3 IA.ro Counter .1.3.6.1.4.1.664.2.141.10.1.1.20 |
adDSUIQIntDBUUnroutableNumber of frames received on a management DLCI destined for the IQ unit
and have the wrong IP address.ro Counter .1.3.6.1.4.1.664.2.141.10.1.1.21 |
adDSUIQDayDBUStatus OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.141.11 |
adDSUIQDayDBUStatusTablen/a. SEQUENCE OF AdDSUIQDayDBUStatusEntry .1.3.6.1.4.1.664.2.141.11.1 |
adDSUIQDayDBUStatusEntryn/a AdDSUIQDayDBUStatusEntry .1.3.6.1.4.1.664.2.141.11.1.1 |
adDSUIQDayDBUSlotIndexn/a.ro INTEGER .1.3.6.1.4.1.664.2.141.11.1.1.1 |
adDSUIQDayDBUFramesRxThe number of Frames the Port received for the interval.ro Counter .1.3.6.1.4.1.664.2.141.11.1.1.2 |
adDSUIQDayDBUFramesTxThe number of Frames the Port transmitted for the interval.ro Counter .1.3.6.1.4.1.664.2.141.11.1.1.3 |
adDSUIQDayDBUBytesRxThe number of Bytes the Port received for the interval.ro Counter .1.3.6.1.4.1.664.2.141.11.1.1.4 |
adDSUIQDayDBUBytesTxThe number of Bytes the Port transmitted for the interval.ro Counter .1.3.6.1.4.1.664.2.141.11.1.1.5 |
adDSUIQDayDBUAvgThruputTxThe Average Throughput the Port transmitted for the interval.ro Gauge .1.3.6.1.4.1.664.2.141.11.1.1.6 |
adDSUIQDayDBUAvgThruputRxThe Average Throughput the Port received for the interval.ro Gauge .1.3.6.1.4.1.664.2.141.11.1.1.7 |
adDSUIQDayDBUMaxThruputTxThe Maximum Throughput the Port transmitted for the interval.ro Counter .1.3.6.1.4.1.664.2.141.11.1.1.8 |
adDSUIQDayDBUMaxThruputRxThe Maximum Throughput the Port received for the interval.ro Counter .1.3.6.1.4.1.664.2.141.11.1.1.9 |
adDSUIQDayDBUAvgUtilizationTxThe Average Utilization the Port transmitted for the interval.ro Gauge .1.3.6.1.4.1.664.2.141.11.1.1.10 |
adDSUIQDayDBUAvgUtilizationRxThe Average Utilization the Port received for the interval.ro Gauge .1.3.6.1.4.1.664.2.141.11.1.1.11 |
adDSUIQDayDBUMaxUtilizationTxThe Maximum Utilization the Port transmitted for the interval.ro Counter .1.3.6.1.4.1.664.2.141.11.1.1.12 |
adDSUIQDayDBUMaxUtilizationRxThe Maximum Utilization the Port received for the interval.ro Counter .1.3.6.1.4.1.664.2.141.11.1.1.13 |
adDSUIQDayTimeInDBUTime in seconds the DBU port was active.ro Counter .1.3.6.1.4.1.664.2.141.11.1.1.14 |
adDSUIQDayDBUCrcErrorsNumber of frames received with CRC errors.ro Counter .1.3.6.1.4.1.664.2.141.11.1.1.15 |
adDSUIQDayDBUAbortFramesNumber of frames received without proper flag termination.ro Counter .1.3.6.1.4.1.664.2.141.11.1.1.16 |
adDSUIQDayDBUOctectViolationsNumber of frames received with a bit count not divisible by eigth.ro Counter .1.3.6.1.4.1.664.2.141.11.1.1.17 |
adDSUIQDayDBUDiscardFramesNumber of frames discarded by the IQ unitro Counter .1.3.6.1.4.1.664.2.141.11.1.1.18 |
adDSUIQDayDBULengthErrorsNumber of frames received that is less than 5 bytes or greater than 4500 bytes.ro Counter .1.3.6.1.4.1.664.2.141.11.1.1.19 |
adDSUIQDayDBUEncapsulationErrorsNumber of frames destined for the IQ IP stack with that does not meet
the FRF.3 IA.ro Counter .1.3.6.1.4.1.664.2.141.11.1.1.20 |
adDSUIQDayDBUUnroutableNumber of frames received on a management DLCI destined for the IQ unit
and have the wrong IP address.ro Counter .1.3.6.1.4.1.664.2.141.11.1.1.21 |
adDSUIQTrapManager OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.141.12 |
adDSUIQTrapManagerTableThe trap manger route table. SEQUENCE OF AdDSUIQTrapManagerEntry .1.3.6.1.4.1.664.2.141.12.1 |
adDSUIQTrapManagerEntryn/a AdDSUIQTrapManagerEntry .1.3.6.1.4.1.664.2.141.12.1.1 |
adDSUIQTrapManagerRouteIndexn/a.ro INTEGER .1.3.6.1.4.1.664.2.141.12.1.1.1 |
adDSUIQTrapManagerRouteIPAddressSets the Trap Manager IP Address.rw IpAddress .1.3.6.1.4.1.664.2.141.12.1.1.2 |
adDSUIQTrapManagerRouteDLCISets the Trap Manager DLCI. (Range 16 - 1007).rw INTEGER .1.3.6.1.4.1.664.2.141.12.1.1.3 |
adDSUIQTrapManagerRoutePortSelects the Trap Manager Port.rw Enumeration .1.3.6.1.4.1.664.2.141.12.1.1.4 |