ZYXEL-PORT-MIB
The subtree for port
Main OID:
zyxelPort.1.3.6.1.4.1.890.1.15.3.61
23
Objects
Active
Status
14
Dependencies
Imported Objects
Objects
23 total| Object Name |
|---|
zyxelPortThe subtree for port MODULE-IDENTITY .1.3.6.1.4.1.890.1.15.3.61 |
RFC1155-SMIThe subtree for port Unknown .1.3.6.1.4.1.890.1.15.3.61 |
IF-MIBThe subtree for port NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.15.3.61 |
zyxelPortSetup OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.15.3.61.1 |
zyxelPortTableThe table contains port configuration. SEQUENCE OF ZyxelPortEntry .1.3.6.1.4.1.890.1.15.3.61.1.1 |
zyxelPortEntryAn entry contains port configuration. ZyxelPortEntry .1.3.6.1.4.1.890.1.15.3.61.1.1.1 |
zyPortSpeedDuplexSelect The speed and the duplex mode of the Ethernet connection on this port. Selecting Auto
(auto-negotiation) allows one port to negotiate with a peer port automatically to obtain the
connection speed and duplex mode that both ends support. When auto-negotiation is turned on,
a port on the Switch negotiates with the peer automatically to determine the connection speed
and duplex mode. If the peer port does not support auto-negotiation or turns off this feature,
the Switch determines the connection speed by detecting the signal on the cable and using half
duplex mode. Thus requiring you to make sure that the settings of the peer port are the same in
order to connect.rw Enumeration .1.3.6.1.4.1.890.1.15.3.61.1.1.1.1 |
zyPortFlowControlStateEnable/Disable the flow control on this port. A concentration of traffic on a port decreases port
bandwidth and overflows buffer memory causing packet discards and frame losses. Flow control is used
to regulate transmission of signals to match the bandwidth of the receiving port.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.15.3.61.1.1.1.2 |
zyPortNameEnter a descriptive name that identifies this port.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.15.3.61.1.1.1.3 |
zyPortIntrusionLockStateEnable/Disable intrusion lock on the port(s) and the port cannot be connected again after you
disconnected the cable.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.15.3.61.1.1.1.4 |
zyPortCX4CableLengthSet the number of meters for the length of the 10GBASE-CX4 cable you use to connect between the swtich
and another switch for stacking.rw Enumeration .1.3.6.1.4.1.890.1.15.3.61.1.1.1.5 |
zyPort10GMediaTypeSet the 10GBase media type.rw Enumeration .1.3.6.1.4.1.890.1.15.3.61.1.1.1.6 |
zyxelPortStatus OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.15.3.61.2 |
zyxelPortInfoTableThe table contains port information. SEQUENCE OF ZyxelPortInfoEntry .1.3.6.1.4.1.890.1.15.3.61.2.1 |
zyxelPortInfoEntryAn entry contains port information. ZyxelPortInfoEntry .1.3.6.1.4.1.890.1.15.3.61.2.1.1 |
zyPortModuleTypeThis entry displays the speed type of modular.ro Enumeration .1.3.6.1.4.1.890.1.15.3.61.2.1.1.1 |
zyPortLinkUpTypeThe entry shows the linkUp cable type (copper, fiber, xfp or cx4) for the combo ports.ro Enumeration .1.3.6.1.4.1.890.1.15.3.61.2.1.1.2 |
zyPortTestStatusThis entry displays latest loopback test status of port while performing loopback test.ro Enumeration .1.3.6.1.4.1.890.1.15.3.61.2.1.1.3 |
zyPortCounterResetEnable this entry can reset port counter record.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.15.3.61.2.1.1.4 |
zyxelPortNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.15.3.61.3 |
zyPortAutonegotiationFailedLink speed and duplex mode autonegotiation has failed. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.15.3.61.3.1 |
zyPortIntrusionLockThe cable is disconnected and the port cannot be connected again. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.15.3.61.3.2 |
zyPortAutonegotiationFailedRecoveredLink speed and duplex mode autonegotiation has recovered from failed. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.15.3.61.3.3 |