ZYXEL-IES5000-MIB
ZyXEL Private MIB
Main OID:
ies5000.1.3.6.1.4.1.890.1.5.13.5
3444
Objects
Active
Status
12
Dependencies
Imported Objects
Objects
3444 total| Object Name |
|---|
zyxel OBJECT IDENTIFIER .1.3.6.1.4.1.890 |
RFC1155-SMIForbidden(0) - Support for G998.4 is disabled.
Preferred(1) - If G998.4 is supported by the far-end, it is enabled.
Forced(2) - The line will only train if G998.4 can be enabled.
Test(3) - G998.4 is enabled in test mode (refer to G998.4, Clause 10.4). Enumeration .1.3.6.1.4.1.890 |
products OBJECT IDENTIFIER .1.3.6.1.4.1.890.1 |
accessSwitch OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5 |
iesSeries OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13 |
ies5000ZyXEL Private MIB MODULE-IDENTITY .1.3.6.1.4.1.890.1.5.13.5 |
acl OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.1 |
dhcp OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.1.1 |
dhcpRelayEnableEnable/disable DHCP relay Option82 function. Note that this object
is obsolete in R1.03 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.1.1 |
dhcpRelay82TableA table that contains DHCP Relay configuration. SEQUENCE OF DhcpRelay82Entry .1.3.6.1.4.1.890.1.5.13.5.1.1.2 |
dhcpRelay82EntryThe entry of DHCP Relay table. DhcpRelay82Entry .1.3.6.1.4.1.890.1.5.13.5.1.1.2.1 |
dhcpRelay82PrimaryServerThe IP address of the DHCP Relay primary server.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.1.1.2.1.1 |
dhcpRelay82SecondaryServerThe IP address of the DHCP Relay secondary server.
This object is supported by R1.02 and later versions.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.1.1.2.1.2 |
dhcpRelay82ActiveServerThe current active DHCP Relay server.
This object is supported by R1.02 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.1.2.1.3 |
dhcpRelay82EnableEnable/disable DHCP relay and Option82 function.
This object is supported by R1.03 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.1.2.1.4 |
dhcpRelay82InfoUser specific Option82 information.
This object is supported by R1.03 and later versions.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.1.1.2.1.5 |
dhcpRelay82RelayModeDHCP relay mode.
This object is supported by R1.03 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.1.2.1.6 |
dhcpRelay82RowStatusRow status of the table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.1.1.2.1.7 |
dhcpRelay82Suboption2EnableEnable/disable Option 82 sub-option 2.
This object is supported by R3.00 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.1.2.1.8 |
dhcpRelay82Suboption2InfoUser specified information for Option 82 sub-option 2.
This object is supported by R3.00 and later versions.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.1.1.2.1.9 |
dhcpRelay82Option82Moderw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.1.2.1.10 |
dhcpRelayInfoUser specific Option82 information. Note that this object
is obsolete in R1.03 and later versions.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.1.1.3 |
maxNumOfDhcpRelay82ConfThe maximum number of rows that can be created in dhcpRelay82Table.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.1.4 |
dhcpRelay82DelimiterTo configure the ASCII value of the delimiter character.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.1.5 |
dhcpRelayOption82CheckEnableEnable/disable system to check option82 in DHCP packets from DHCP server.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.1.6 |
dot1x OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.1.2 |
dot1xEnableEnable/disable the 802.1x function.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.2.1 |
radiusServerTableA table that contains Radius Server information. SEQUENCE OF RadiusServerEntry .1.3.6.1.4.1.890.1.5.13.5.1.2.2 |
radiusServerEntryThe entry of Radius Server table. RadiusServerEntry .1.3.6.1.4.1.890.1.5.13.5.1.2.2.1 |
radiusServerIndexThe identity of the RADIUS server.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.2.2.1.1 |
radiusServerIpThe IP address of the Radius Server.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.1.2.2.1.2 |
radiusServerPortThe UDP port of the Radius Server.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.2.2.1.3 |
radiusServerSecretThe shared secret of the Radius Server.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.1.2.2.1.4 |
dot1xPortTableThis table includes 802.1x port configuration. SEQUENCE OF Dot1xPortEntry .1.3.6.1.4.1.890.1.5.13.5.1.2.3 |
dot1xPortEntryAn entry in dot1xPortTable. Dot1xPortEntry .1.3.6.1.4.1.890.1.5.13.5.1.2.3.1 |
dot1xPortEnableEnable/disable 802.1x for the port.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.2.3.1.1 |
dot1xPortControlThe object defines the 802.1x control type for the port.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.2.3.1.2 |
dot1xPortReAuthEnableEnable/disable 802.1x re-authentication for the port.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.2.3.1.3 |
dot1xPortReAuthPeriodThe object defines the 802.1x re-authentication period for the port.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.2.3.1.4 |
dot1xBatchSet OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.1.2.4 |
dot1xTargetThis managed object is used for identify the target on which
the port configuration should be performed. The target is encoded as:
Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7
Byte 2~4: each octet specifies a set of eight slots, with the
first octet specifying slots 1 through 8, and the second
octet specifying slots 9 through 16, and so on.
Byte 5~: each octet specifies a set of eight ports, with the first
octet specifying ports 1 through 8, etc.rw OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.1.2.4.1 |
dot1xOpsThe corresponding bit is set to 1 to start the operation.
The various bit positions are:
BIT 1: enable dot1x
BIT 2: disable dot1x
BIT 3: set dot1x control to be auto
BIT 4: set dot1x control to be forceAuth
BIT 5: set dot1x control to be forceUnAuth
BIT 6: enable dot1x re-authentication
BIT 7: disable dot1x re-authentication
BIT 8: set dot1x re-authentication period.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.2.4.2 |
dot1xReAuthPeriodForBatchSetThe object defines the 802.1x re-authentication period for batch setting.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.2.4.3 |
macfilter OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.1.3 |
macFilterPortTableThis table includes the status of mac filtering for each port. SEQUENCE OF MacFilterPortEntry .1.3.6.1.4.1.890.1.5.13.5.1.3.1 |
macFilterPortEntryAn entry in macFilterPortTable. MacFilterPortEntry .1.3.6.1.4.1.890.1.5.13.5.1.3.1.1 |
macFilterPortEnableEnable/disable MAC filtering for the port.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.3.1.1.1 |
macFilterPortMacCountThe total number of MAC addresses allowed for the port.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.3.1.1.2 |
macFilterPortFilterModeThe mac filter mode (accept or deny) for the port.
This object is supported by R1.02 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.3.1.1.3 |
maxNumOfMacFiltersInSystemThe max number of mac filters supported in the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.3.2 |
maxNumOfMacFiltersPerPortThe max number of mac filters supported per port.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.3.3 |
currNumOfMacFiltersInSystemThe current number of mac filters in the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.3.4 |
macFilterTableA table that contains the mac filter addresses. SEQUENCE OF MacFilterEntry .1.3.6.1.4.1.890.1.5.13.5.1.3.5 |
macFilterEntryThe entry of macFilterTable. MacFilterEntry .1.3.6.1.4.1.890.1.5.13.5.1.3.5.1 |
macFilterAddrThe mac address which can pass through or be rejected from the port.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.1.3.5.1.1 |
macFilterRowStatusThe row status of the entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.1.3.5.1.2 |
macfilterBatchSet OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.1.3.6 |
macfilterTargetThis managed object is used for identify the target on which
the port configuration should be performed. The target is encoded as:
Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7
Byte 2~4: each octet specifies a set of eight slots, with the
first octet specifying slots 1 through 8, and the second
octet specifying slots 9 through 16, and so on.
Byte 5~: each octet specifies a set of eight ports, with the first
octet specifying ports 1 through 8, etc.rw OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.1.3.6.1 |
macfilterOpsThe corresponding bit is set to 1 to start the operation.
The various bit positions are:
BIT 1: enable mac filter
BIT 2: enable mac count filter
BIT 3: disable mac filter
BIT 4: set mac count.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.3.6.2 |
macFilterMacCountForBatchSetThe total number of MAC addresses allowed for a port.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.3.6.3 |
ouiFilterTableA table that contains the OUI filter addresses. SEQUENCE OF OuiFilterEntry .1.3.6.1.4.1.890.1.5.13.5.1.3.7 |
ouiFilterEntryThe entry of ouiFilterTable. OuiFilterEntry .1.3.6.1.4.1.890.1.5.13.5.1.3.7.1 |
ouiFilterAddrThe first three bytes of the mac address which can pass through or be rejected from the port.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.1.3.7.1.1 |
ouiFilterRowStatusThe row status of the entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.1.3.7.1.2 |
maxNumOfOuiFiltersPerPortThe max number of OUI filters supported per port.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.3.8 |
macFilterStatusTableA table that contains the mac filter addresses. SEQUENCE OF MacFilterStatusEntry .1.3.6.1.4.1.890.1.5.13.5.1.3.9 |
macFilterStatusEntryThe entry of macFilterStatusTable. MacFilterStatusEntry .1.3.6.1.4.1.890.1.5.13.5.1.3.9.1 |
macFilterStatusIdThe index of the entry.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.3.9.1.1 |
macFilterStatusAddrThe mac address which can pass through or be rejected from the port.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.1.3.9.1.2 |
macFilterPerPVCTableA table for per-PVC macfilter configuration. SEQUENCE OF MacFilterPerPVCEntry .1.3.6.1.4.1.890.1.5.13.5.1.3.10 |
macFilterPerPVCEntryThe entry of macFilterPerPVCTable. MacFilterPerPVCEntry .1.3.6.1.4.1.890.1.5.13.5.1.3.10.1 |
macFilterPerPVCVpiVPI of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.3.10.1.1 |
macFilterPerPVCVciVCI of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.3.10.1.2 |
macFilterPerPVCEnableEnable/disable MAC filtering for the port-vpi/vcirw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.3.10.1.3 |
macFilterPerPVCModeThe mac filter mode (accept or deny) for the port-vpi/vci.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.3.10.1.4 |
macFilterPerPVCMacCountThe total number of MAC addresses allowed for the port-vpi/vci.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.3.10.1.5 |
macFilterPerPVCMACTableA table for per-PVC macfilter configuration. SEQUENCE OF MacFilterPerPVCMACEntry .1.3.6.1.4.1.890.1.5.13.5.1.3.11 |
macFilterPerPVCMACEntryThe entry of macFilterPerPVCMACTable. MacFilterPerPVCMACEntry .1.3.6.1.4.1.890.1.5.13.5.1.3.11.1 |
macFilterPerPVCMACVpiVPI of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.3.11.1.1 |
macFilterPerPVCMACVciVCI of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.3.11.1.2 |
macFilterPerPVCMACAddrThe mac address which can pass through or be rejected from the port-vpi/vciro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.1.3.11.1.3 |
macFilterPerPVCMACRowStatusThe row status of the entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.1.3.11.1.4 |
pktfilter OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.1.4 |
pktFilterPortTableThis table includes packet filtering for each port. SEQUENCE OF PktFilterPortEntry .1.3.6.1.4.1.890.1.5.13.5.1.4.1 |
pktFilterPortEntryAn entry in pktFilterPortTable. PktFilterPortEntry .1.3.6.1.4.1.890.1.5.13.5.1.4.1.1 |
pktFilterThe packet filter. The semantic for each bit is:
BIT 1: accept all
BIT 2: accept PPPoE only
BIT 3: reject ARP
BIT 4: reject DHCP
BIT 5: reject EAPOL
BIT 6: reject PPPoE
BIT 7: reject NetBIOS
BIT 8: reject IGMP
BIT 9: reject IPrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.4.1.1.1 |
pktfilterBatchSet OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.1.4.2 |
pktfilterTargetThis managed object is used for identify the target on which
the port configuration should be performed. The target is encoded as:
Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7
Byte 2~4: each octet specifies a set of eight slots, with the
first octet specifying slots 1 through 8, and the second
octet specifying slots 9 through 16, and so on.
Byte 5~: each octet specifies a set of eight ports, with the first
octet specifying ports 1 through 8, etc.rw OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.1.4.2.1 |
pktfilterOpsThe corresponding bit is set to 1 to start the operation.
The various bit positions are:
BIT 1: set packet filter.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.4.2.2 |
pktfilterForBatchSetThe packet filter for batch setting. The semantic for each bit is identical to the object pktFilter.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.4.2.3 |
pktFilterPerPVCTableThis table includes per-PVC packet filter configuration. SEQUENCE OF PktFilterPerPVCEntry .1.3.6.1.4.1.890.1.5.13.5.1.4.3 |
pktFilterPerPVCEntryAn entry in pktFilterPerPVCTable. PktFilterPerPVCEntry .1.3.6.1.4.1.890.1.5.13.5.1.4.3.1 |
pktFilterPerPVCVpiVPI of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.4.3.1.1 |
pktFilterPerPVCVciVCI of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.4.3.1.2 |
pktFilterPerPVCpktFilterThe packet filter. The semantic for each bit is:
BIT 1: accept all
BIT 2: accept PPPoE only
BIT 3: reject ARP
BIT 4: reject DHCP
BIT 5: reject EAPOL
BIT 6: reject PPPoE
BIT 7: reject NetBIOS
BIT 8: reject IGMP
BIT 9: reject IPrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.4.3.1.3 |
dhcpSnoop OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.1.5 |
dhcpSnoopPortTableThis table includes DHCP snooping enable/disable for each port.
This table is supported by R1.02 and later versions. SEQUENCE OF DhcpSnoopPortEntry .1.3.6.1.4.1.890.1.5.13.5.1.5.1 |
dhcpSnoopPortEntryAn entry of dhcpSnoopPortTable. DhcpSnoopPortEntry .1.3.6.1.4.1.890.1.5.13.5.1.5.1.1 |
dhcpSnoopEnableEnable/disable DHCP snooping for a port.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.5.1.1.1 |
dhcpSnoopTargetThis managed object is used for identify the target on which
the operation should be performed. The target is encoded as:
Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7
Byte 2~4: each octet specifies a set of eight slots, with the
first octet specifying slots 1 through 8, and the second
octet specifying slots 9 through 16, and so on.
Byte 5~: each octet specifies a set of eight ports, with the first
octet specifying ports 1 through 8, etc.rw OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.1.5.2 |
dhcpSnoopOpsThe corresponding bit is set to 1 to start the operation.
The various bit positions are:
BIT 1: DHCP snooping table flush.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.5.3 |
dhcpStaticTableThis table defines DHCP static IP addresses.
This table is supported by R1.03 and later versions. SEQUENCE OF DhcpStaticEntry .1.3.6.1.4.1.890.1.5.13.5.1.5.4 |
dhcpStaticEntryAn entry of dhcpStaticTable. DhcpStaticEntry .1.3.6.1.4.1.890.1.5.13.5.1.5.4.1 |
dhcpStaticIpAddrThe IP address which can pass through the port.ro IpAddress .1.3.6.1.4.1.890.1.5.13.5.1.5.4.1.1 |
dhcpStaticRowStatusRow status of the table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.1.5.4.1.2 |
maxNumOfDhcpStaticIpThe maximum number of DHCP static IP addresses which can be created for a port.
This object is supported by R1.03 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.5.5 |
dhcpSnoopLan2lanTableSupport DHCP lan2lan to prevent DHCP service hack
if customer installed DHCP server in its subscriber network.
This table is supported by R5.05 and later versions. SEQUENCE OF DhcpSnoopLan2lanEntry .1.3.6.1.4.1.890.1.5.13.5.1.5.6 |
dhcpSnoopLan2lanEntryThe entry of dhcpSnoopLan2lanTable. DhcpSnoopLan2lanEntry .1.3.6.1.4.1.890.1.5.13.5.1.5.6.1 |
dhcpSnoopLan2lanEnableEnable/disable DHCP server on subscriber portrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.5.6.1.1 |
aclRule OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.1.6 |
aclSetTableThis table is supported by R1.03 and later versions. SEQUENCE OF AclSetEntry .1.3.6.1.4.1.890.1.5.13.5.1.6.1 |
aclSetEntryAn entry of aclSetTable. AclSetEntry .1.3.6.1.4.1.890.1.5.13.5.1.6.1.1 |
aclSetVpiVPI value.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.6.1.1.1 |
aclSetVciVCI value.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.6.1.1.2 |
aclSetProfileNameACL Profile name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.1.6.1.1.3 |
aclSetRowStatusRowStatus of aclSetEntry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.1.6.1.1.4 |
aclNoMatchTableThis table is supported by R5.02 and later versions. SEQUENCE OF AclNoMatchEntry .1.3.6.1.4.1.890.1.5.13.5.1.6.2 |
aclNoMatchEntryAn entry of aclNoMatchTable. AclNoMatchEntry .1.3.6.1.4.1.890.1.5.13.5.1.6.2.1 |
aclNoMatchActionPass or drop the packet.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.6.2.1.1 |
pppoeAgent OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.1.7 |
pppoeAgentTableA table that contains PPPoE DHCP Relay configuration.
This table is supported by R1.03 and later versions. SEQUENCE OF PppoeAgentEntry .1.3.6.1.4.1.890.1.5.13.5.1.7.1 |
pppoeAgentEntryAn entry of pppoeAgentTable. PppoeAgentEntry .1.3.6.1.4.1.890.1.5.13.5.1.7.1.1 |
pppoeAgentEnableEnable/disable DHCP relay and Option82 function.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.7.1.1.1 |
pppoeAgentInfoUser specific Option82 information.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.1.7.1.1.2 |
pppoeAgentRowStatusRow status of the table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.1.7.1.1.3 |
pppoeAgentOptionModerw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.7.1.1.4 |
maxNumOfPppoeDhcpRelay82ConfThe maximum number of rows that can be created in pppoeAgentTable.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.7.2 |
pppoeAgentDelimiterTo configure the ASCII value of the delimiter character.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.7.3 |
dsBcast OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.1.8 |
dsBcastTableA table that contains downstream broadcast forbidden configuration.
This table is supported by R3.00 and later versions. SEQUENCE OF DsBcastEntry .1.3.6.1.4.1.890.1.5.13.5.1.8.1 |
dsBcastEntryAn entry of dsBcastTable. DsBcastEntry .1.3.6.1.4.1.890.1.5.13.5.1.8.1.1 |
dsBcastRowStatusRow status of the table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.1.8.1.1.1 |
usBcast OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.1.9 |
usBcastCtrlEnableEnable/disable upstream broadcast control.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.9.1 |
usBcastCtrlRaterw INTEGER UNITS "Kbps" .1.3.6.1.4.1.890.1.5.13.5.1.9.2 |
dscpMapping OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.1.10 |
dscpMappingTableThe table contains DSCP mapping configuration. SEQUENCE OF DscpMappingEntry .1.3.6.1.4.1.890.1.5.13.5.1.10.1 |
dscpMappingEntryAn entry of dscpMappingTable. DscpMappingEntry .1.3.6.1.4.1.890.1.5.13.5.1.10.1.1 |
dscpMappingSrcCodePointThe DSCP source code point used for mapping.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.10.1.1.1 |
dscpMappingMapPriorityThe mapping p bits that will replace the source p bits in the incoming packet.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.10.1.1.2 |
dscpPortTableThe table contains DSCP port configuration. SEQUENCE OF DscpPortEntry .1.3.6.1.4.1.890.1.5.13.5.1.10.2 |
dscpPortEntryAn entry of dscpPortTable. DscpPortEntry .1.3.6.1.4.1.890.1.5.13.5.1.10.2.1 |
dscpPortEnableEnable/disable DSCP.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.10.2.1.1 |
macAntiSpoofEnableEnable/disable MAC anti-spoof.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.13 |
subnetvlan OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.1.14 |
subnetvlanStatusrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.14.1 |
subnetvlanTableA table that contains subnet vlan configuration. SEQUENCE OF SubnetvlanEntry .1.3.6.1.4.1.890.1.5.13.5.1.14.2 |
subnetvlanEntryThe entry of subnet vlan table. SubnetvlanEntry .1.3.6.1.4.1.890.1.5.13.5.1.14.2.1 |
subnetvlanIpro IpAddress .1.3.6.1.4.1.890.1.5.13.5.1.14.2.1.1 |
subnetvlanMaskro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.14.2.1.2 |
subnetvlanVidro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.14.2.1.3 |
subnetvlanPriorityro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.14.2.1.4 |
subnetvlanNamerw DisplayString .1.3.6.1.4.1.890.1.5.13.5.1.14.2.1.5 |
subnetvlanRowStatusRow status of the table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.1.14.2.1.6 |
subnetvlanInetTableA table that contains IPv4/IPv6 subnet vlan configuration. SEQUENCE OF SubnetvlanInetEntry .1.3.6.1.4.1.890.1.5.13.5.1.14.3 |
subnetvlanInetEntryThe entry of subnet vlan inet table. SubnetvlanInetEntry .1.3.6.1.4.1.890.1.5.13.5.1.14.3.1 |
subnetvlanInetAddrTypero InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.1.14.3.1.1 |
subnetvlanInetAddrro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.1.14.3.1.2 |
subnetvlanInetMaskro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.14.3.1.3 |
subnetvlanInetVidro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.14.3.1.4 |
subnetvlanInetPriorityro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.14.3.1.5 |
subnetvlanInetNamerw DisplayString .1.3.6.1.4.1.890.1.5.13.5.1.14.3.1.6 |
subnetvlanInetRowStatusRow status of the table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.1.14.3.1.7 |
loopguard OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.1.15 |
loopguardTableA table that contains Loopguard configuration. SEQUENCE OF LoopguardEntry .1.3.6.1.4.1.890.1.5.13.5.1.15.1 |
loopguardEntryThe entry of Loopguard table. LoopguardEntry .1.3.6.1.4.1.890.1.5.13.5.1.15.1.1 |
loopguardStatusrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.15.1.1.1 |
loopguardModerw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.15.1.1.2 |
loopguardRecoverTimesecondsrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.15.1.1.3 |
usStorm OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.1.16 |
usStormTableA table that contains UsStorm configuration. SEQUENCE OF UsStormEntry .1.3.6.1.4.1.890.1.5.13.5.1.16.1 |
usStormEntryThe entry of UsStorm table. UsStormEntry .1.3.6.1.4.1.890.1.5.13.5.1.16.1.1 |
usStormBcastThresh0~1488096 pkt/s, -1 means no limitrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.16.1.1.1 |
usStormMcastThresh0~1488096 pkt/s, -1 means no limitrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.16.1.1.2 |
usStormUcastThresh0~1488096 pkt/s, -1 means no limitrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.16.1.1.3 |
arpInspection OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.1.17 |
arpInspectionTableSupport ARP inspection to filter unauthorized ARP packets on the network.
This can prevent many kinds of man-in-the-middle attacks.
This table is supported by R5.05 and later versions. SEQUENCE OF ArpInspectionEntry .1.3.6.1.4.1.890.1.5.13.5.1.17.1 |
arpInspectionEntryThe entry of arpInspectionTable. ArpInspectionEntry .1.3.6.1.4.1.890.1.5.13.5.1.17.1.1 |
arpInspectionEnableEnable/disable arp inspection on the specified subscriber port.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.17.1.1.1 |
macFF OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.1.18 |
macFFStaticTable SEQUENCE OF MacFFStaticEntry .1.3.6.1.4.1.890.1.5.13.5.1.18.1 |
macFFStaticEntryThe entry of macFFStaticTable. MacFFStaticEntry .1.3.6.1.4.1.890.1.5.13.5.1.18.1.1 |
macFFStaticIndexThe macFF static entry index 1 ~ 24ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.18.1.1.1 |
macFFStaticSrcIPMatched range for static subscriber's IP in ARP requestrw IpAddress .1.3.6.1.4.1.890.1.5.13.5.1.18.1.1.2 |
macFFStaticMaskMatched range for static subscriber's IP in ARP requestrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.18.1.1.3 |
macFFStaticArasIPIP of static macFF Access Router/App Serverrw IpAddress .1.3.6.1.4.1.890.1.5.13.5.1.18.1.1.4 |
macFFStaticVidvlan ID of macFF Access Router/App Serverrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.18.1.1.5 |
macFFStaticRowStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.1.18.1.1.6 |
macFFDynamicTable SEQUENCE OF MacFFDynamicEntry .1.3.6.1.4.1.890.1.5.13.5.1.18.2 |
macFFDynamicEntryThe entry of macFFDynamicTable. MacFFDynamicEntry .1.3.6.1.4.1.890.1.5.13.5.1.18.2.1 |
macFFDynamicIndexThe macFF entry index 1 ~ 24ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.18.2.1.1 |
macFFDynamicSrcIPMatched range for dynamic subscriber's IP in ARP requestro IpAddress .1.3.6.1.4.1.890.1.5.13.5.1.18.2.1.2 |
macFFDynamicMaskMatched range for dynamic subscriber's IP in ARP requestro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.18.2.1.3 |
macFFDynamicArasIPIP of dynamic macFF Access Router/App Serverro IpAddress .1.3.6.1.4.1.890.1.5.13.5.1.18.2.1.4 |
macFFDynamicVidvlan ID of macFF Access Router/App Serverro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.18.2.1.5 |
macFFVlanTable SEQUENCE OF MacFFVlanEntry .1.3.6.1.4.1.890.1.5.13.5.1.18.3 |
macFFVlanEntryThe entry of macFFVlanTable. MacFFVlanEntry .1.3.6.1.4.1.890.1.5.13.5.1.18.3.1 |
macFFVlanVidVlan ID of macFF Access Router/App Serverro INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.18.3.1.1 |
macFFVlanRowStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.1.18.3.1.2 |
macFFFlushSet the object to n to flush the slot n's macff arp table(not include the MSC slot).
macFFArpStatusUplinkTable(1.3.6.1.4.1.890.1.5.13.5.13.23.1)
macFFArpStatusSlotTable(1.3.6.1.4.1.890.1.5.13.5.13.23.2)rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.1.18.4 |
dhcpv6 OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.1.19 |
dhcpv6RelayTable SEQUENCE OF Dhcpv6RelayEntry .1.3.6.1.4.1.890.1.5.13.5.1.19.1 |
dhcpv6RelayEntryThe entry of dhcpv6RelayTable. Dhcpv6RelayEntry .1.3.6.1.4.1.890.1.5.13.5.1.19.1.1 |
dhcpv6RelayLdraStateEnable/disable DHCPv6 LDRA functionrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.19.1.1.1 |
dhcpv6RelayRowStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.1.19.1.1.2 |
dhcpv6RelayOptionTable SEQUENCE OF Dhcpv6RelayOptionEntry .1.3.6.1.4.1.890.1.5.13.5.1.19.2 |
dhcpv6RelayOptionEntryThe entry of dhcpv6RelayOptionTable. Dhcpv6RelayOptionEntry .1.3.6.1.4.1.890.1.5.13.5.1.19.2.1 |
dhcpv6RelayOptionIdDHCPv6 option IDro Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.19.2.1.1 |
dhcpv6RelayOptionStateEnable/disable DHCPv6 optionrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.1.19.2.1.2 |
dhcpv6RelayOptionFormatUser specific Option format
'%' treated as a beginner of predefined runtime variable
the rule is below:
%%: equals character %
%0x00~0xFF: represents byte value
%pname: configured port name
%ptel: configured port tel
%pid: port index
%chvpi: channel vpi
%chvci: channel vci
%slotid: slot index of the logic port
%svlan: SVLAN ID which DHCP client runs on
%cvlan: CVLAN ID which DHCP client runs on
%hname: host device name
%cmac: MAC address of client, represents as Byte
%phtype: ATM: 'atm' Ethernet 'eth'
%blank: blank characterrw OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.1.19.2.1.3 |
alarmconf OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.2 |
alarmOpsThe manager sets the corresponding bit value to 1 to start the operation
and the agent clears the object to zero when the operation is successfully completed.
The various bit positions are:
BIT 1: clear
BIT 2: cutoff
BIT 3: clear alarm history tablerw INTEGER .1.3.6.1.4.1.890.1.5.13.5.2.1 |
alarmConfTableThis table includes alarm configuration. SEQUENCE OF AlarmConfEntry .1.3.6.1.4.1.890.1.5.13.5.2.2 |
alarmConfEntryAn entry in alarmConfTable. AlarmConfEntry .1.3.6.1.4.1.890.1.5.13.5.2.2.1 |
alarmConfId3: dslLineUp
4: dslLineDown
7: dslLineLdmStart
8: dslLineLdmDone
9: dslLinePowerDownL2
10:dslLinePowerDownL0
11:dslLineFailure
14:adslPerfLolThresh
17:adslPerfLofThresh
18:adslPerfLosThresh
19:adslPerfLprThresh
20:adslPerfESThresh
21:adslRateChange
22:adslPerfSESThresh
23:adslPerfUASThresh
24:shdslLoopAttenCrossing
25:shdslSNRMarginCrossing
26:shdslPerfESThresh
27:shdslPerfSESThresh
28:shdslPerfCRCAnomaliesThresh
29:shdslPerfLOSWSThresh
30:shdslPerfUASThresh
31:vdslPerfLolThresh
32:vdslPerfLofThresh
33:vdslPerfLosThresh
34:vdslPerfLprThresh
35:vdslPerfESThresh
36:vdslPerfSESThresh
37:vdslPerfUASThresh
38:dslMacAntiSpoofing
39:vdslPerfCodeViolationThresh
40:vdslVturInfoReady
41:vdslPerfRateChange
42:vdslTCACorrect
43:vdslTCAFailinit
44:vdslTCAFEC
45:vdslStatusChange
46:lineLoopGuard
1001:eqpt48VPowerFailure
1002:eqptVoltageError
1003:eqptTempError
1004:eqptFanError
1005:eqptTempLowFanStop
1009:eqptHWMonitorFailre
1011:eqptColdStart
1012:eqptWarmStart
1019:eqptMgmtPortUp
1020:eqptMgmtPortDown
1021:eqptExternalAlarmInput
1022:eqptTopologyChange
1023:eqptFWUploadOK
1024:eqptFWUploadFailure
1025:eqptLTPlugIn
1026:eqptLTPullOut
1028:eqptLTDslDeviceFailure
1029:eqptLTDslDeviceRedownload
1031:eqptLTActive
1032:eqptLTInactive
1038:eqptLTFWUploadOK
1039:eqptLTFWUploadFailure
1040:eqptLTEnable
1041:eqptLTDisable
1042:eqptLTReset
1043:eqptNTSwitchOK
1044:eqptCpuUtilizationHigh
1045:eqptVopBatteryFailure
1046:eqptVopClockFailure
1047:eqptVopRingerFault
1048:eqptPacketBufferUsageHigh
1049:eqptMemoryUsageHigh
1050:eqptStpNewRoot
1053:eqptStpPortStateChange
1054:eqptStpPortRoleChange
2001:sysReboot
2002:sysConfigChange
2003:sysConfigUploadOK
2004:sysConfigUploadFailure
2005:sysTimeSyncFailure
2006:sysAlarmCutoffEnable
2007:sysAlarmClearEnable
2008:sysLoginFailure
2009:sysLogin
2010:sysAccountAdded
2011:sysAccountDeleted
2012:sysAccountModified
2013:sysSvrSyncProfOk
2014:sysSvrSyncProfFail
2015:sysCliSyncProfOk
2016:sysCliSyncProfFail
2017:sysMacAntiSpoofing
2018:sysClusterMemberActive
2019:sysClusterMemberInactive
2020:sysClusterMemeberAdded
2021:sysClusterMemeberDeleted
2022:pingProbeFailed
2023:pingTestFailed
2024:pingTestCompleted
2025:traceRouteTestFailed
2026:traceRouteTestCompleted
3006:enetUp
3007:enetDown
3008:enetLoopGuard
3009:enetSFPError
3010:enetSFPTxEnable
3011:enetSFPTxDisable
4001:vopTempError
4002:vopDCPowerFailure
4003:vopACPowerFailure
4004:vopRingTimerFailure
4005:vopRingResourceFailure
4006:vopRingOhdFailure
4007:vopNoFreeDSPChannel
4008:vopMCMissing
4009:vopSCMissing
4010:vopTermNameDup
4011:vopNoProtection
4012:vopProtectionSwitch
4013:vopDropCall
4014:vopBatteryFail
4015:vopClockFail
4016:vopRingerFail
4017:vopMgcMissing
4018:vopMgEnable
4019:vopMgDisable
5001:cfmError
5003:lldpRemoteChange
6001: imaAlarmGroupStartupFe
6002: imaAlarmGroupCfgAbort
6003: imaAlarmGroupCfgAbortFe
6004: imaAlarmGroupInsuffLinks
6005: imaAlarmGroupInsuffLinksFe
6006: imaAlarmGroupBlockedFe
6007: imaAlarmGroupTimingSynch
6008: imaAlarmLinkLif
6009: imaAlarmLinkLods
6010: imaAlarmLinkRfi
6011: imaAlarmLinkTxMisConnect
6012: imaAlarmLinkRxMisConnect
6013: imaAlarmLinkTxFault
6014: imaAlarmLinkRxFault
6015: imaAlarmLinkTxUnusableFe
6016: imaAlarmLinkRxUnusableFe
7001: e1AlarmLinkLOS
7002: e1AlarmPathLOF
7003: e1AlarmPathAIS
7004: e1AlarmPathRDI
7005: e1AlarmPathOCASMF
7006: e1AlarmPathOCRCMF
7007: e1AlarmLinkSF
7008: e1AlarmLinkSD
7009: e1AlarmTCAQuarterES
7010: e1AlarmTCAQuarterSES
7011: e1AlarmTCAQuarterUAS
7012: e1AlarmTCADayES
7013: e1AlarmTCADaySES
7014: e1AlarmTCADayUASro INTEGER .1.3.6.1.4.1.890.1.5.13.5.2.2.1.1 |
alarmConfFacilityAlarm facility.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.2.2.1.2 |
alarmConfTargetThe destination which alarms are reported to. Set the bit to 1 to enable the target.
BIT 1: snmp trap
BIT 2: syslogrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.2.2.1.3 |
alarmConfSeverityAlarm severityrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.2.2.1.4 |
alarmConfClearableSetting the object to one indicates that the alarm is to be cleared when user submits alarm clear.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.2.2.1.5 |
alarmCurrTableThis table includes current alarm information. SEQUENCE OF AlarmCurrEntry .1.3.6.1.4.1.890.1.5.13.5.2.3 |
alarmCurrEntryAn entry in alarmCurrTable. AlarmCurrEntry .1.3.6.1.4.1.890.1.5.13.5.2.3.1 |
alarmCurrIndexIndex of the alarm.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.2.3.1.1 |
alarmCurrOccurTimeAlarm occurence time (in hundredths of a second) since the system was last re-initialized.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.890.1.5.13.5.2.3.1.2 |
alarmCurrTrapOidTrap OID of the alarm.ro OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.2.3.1.3 |
alarmCurrParam1The 1st parameter of the alarm.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.2.3.1.4 |
alarmCurrParam2The 2nd parameter of the alarm.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.2.3.1.5 |
alarmCurrParam3The 3rd parameter of the alarm.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.2.3.1.6 |
alarmCurrParam4The 4th parameter of the alarm.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.2.3.1.7 |
alarmCurrParam5The 5th parameter of the alarm.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.2.3.1.8 |
alarmCurrParam6The 6th parameter of the alarm.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.2.3.1.9 |
alarmCurrParam7The 7th parameter of the alarm.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.2.3.1.10 |
alarmCurrParam8The 8th parameter of the alarm.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.2.3.1.11 |
alarmCurrTimeDescrThe string representation of occurence time (YYYY/MM/DD HH:MM:SS).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.2.3.1.12 |
alarmCurrSeverityThe severity of the alarm.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.2.3.1.13 |
alarmCurrDescrThe description of the alarm.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.2.3.1.14 |
alarmSeverityPortTableThis table includes the configuration of alarm reporting severity threshold for each port. SEQUENCE OF AlarmSeverityPortEntry .1.3.6.1.4.1.890.1.5.13.5.2.4 |
alarmSeverityPortEntryAn entry in alarmSeverityPortTable. AlarmSeverityPortEntry .1.3.6.1.4.1.890.1.5.13.5.2.4.1 |
severityThreshThe minimum alarm severity that is reported.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.2.4.1.1 |
externalAlarmTableThis table includes the configuration of external alarms. SEQUENCE OF ExternalAlarmEntry .1.3.6.1.4.1.890.1.5.13.5.2.5 |
externalAlarmEntryAn entry in externalAlarmTable. ExternalAlarmEntry .1.3.6.1.4.1.890.1.5.13.5.2.5.1 |
externalAlarmIndexThe external alarm index.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.2.5.1.1 |
externalAlarmNameThe external alarm name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.2.5.1.2 |
alarmTargetThe manager sets the corresponding bit value to 1 to start the operation and
the agent clears the object to zero when the operation is successfully completed.
The various bit positions are:
BIT 1: clear
BIT 2: cutoffrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.2.6 |
alarmHisTableThis table that contains alarm history data.
This table is supported by R5.05 and later versions. SEQUENCE OF AlarmHisEntry .1.3.6.1.4.1.890.1.5.13.5.2.7 |
alarmHisEntryAn entry in alarmHisTable. AlarmHisEntry .1.3.6.1.4.1.890.1.5.13.5.2.7.1 |
alarmHisIndexIndex of the alarm.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.2.7.1.1 |
alarmHisOccurTimeAlarm occurence time (in hundredths of a second) since the system was last re-initialized.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.890.1.5.13.5.2.7.1.2 |
alarmHisTrapOidTrap OID of the alarm.ro OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.2.7.1.3 |
alarmHisParam1The 1st parameter of the alarm.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.2.7.1.4 |
alarmHisParam2The 2nd parameter of the alarm.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.2.7.1.5 |
alarmHisParam3The 3rd parameter of the alarm.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.2.7.1.6 |
alarmHisParam4The 4th parameter of the alarm.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.2.7.1.7 |
alarmHisParam5The 5th parameter of the alarm.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.2.7.1.8 |
alarmHisParam6The 6th parameter of the alarm.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.2.7.1.9 |
alarmHisParam7The 7th parameter of the alarm.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.2.7.1.10 |
alarmHisParam8The 8th parameter of the alarm.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.2.7.1.11 |
alarmHisTimeDescrThe string representation of occurence time (YYYY/MM/DD HH:MM:SS).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.2.7.1.12 |
alarmHisSeverityThe severity of the alarm.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.2.7.1.13 |
alarmHisDescrThe description of the alarm.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.2.7.1.14 |
alarmHisFilter OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.2.8 |
alarmHisFilterByIfIndexifIndex Filter for alarmHisTable.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.2.8.1 |
config OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.3 |
configOpsThe manager sets the corresponding bit value to 1 to start the operation
and the agent clears the object to zero when the operation is successfully completed.
The various bit positions are:
BIT 1: config save
BIT 2: factory defaultrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.3.1 |
diagnostic OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.4 |
loopback OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.4.1 |
loopbackTargetIfIndex of the port which would be performed loopback test.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.1.1 |
loopbackOpsThe manager sets the corresponding bit value to 1 to start the loopback test
and the agent clears the object to zero when loopback test is successfully completed.
The various bit positions are:
BIT 1: local loopback
BIT 2: remote F5 loopback.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.1.2 |
loopbackVpiVPI of the virtual channel which would be performed loopback test.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.1.3 |
loopbackVciVCI of the virtual channel which would be performed loopback test.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.1.4 |
loopbackStatusLoopback test status message.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.4.1.5 |
ldm OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.4.2 |
ldmTargetIfIndex of the port which would be performed ldm test.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.2.1 |
ldmOpsThe manager sets the object to 1 to start the ldm test
and the agent clears the object to zero when ldm test is successfully completed.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.2.2 |
ldmStatusStatus description of ldm test result.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.4.2.3 |
ldmAtucLoopAttenuationLoop Attenuation.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.2.4 |
ldmAtucSignalAttenuationSignal Attenuation.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.2.5 |
ldmAtucSignalMarginSignal Margin.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.2.6 |
ldmAtucAggregateTxPowerActual Aggregate Transmit Power.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.2.7 |
ldmAtucAttainableBitRateAttainable Bit Rate.ro Unsigned32 UNITS "bits per second" .1.3.6.1.4.1.890.1.5.13.5.4.2.8 |
ldmAturLoopAttenuationLoop Attenuation.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.2.9 |
ldmAturSignalAttenuationSignal Attenuation.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.2.10 |
ldmAturSignalMarginSignal Margin.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.2.11 |
ldmAturAggregateTxPowerActual Aggregate Transmit Power.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.2.12 |
ldmAturAttainableBitRateAttainable Bit Rate.ro Unsigned32 UNITS "bits per second" .1.3.6.1.4.1.890.1.5.13.5.4.2.13 |
ldmAtucNumOfSubcarriersPerPortThe number of subcarriers per port for ATU-C.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.2.14 |
ldmAturNumOfSubcarriersPerPortThe number of subcarriers per port for ATU-R.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.2.15 |
ldmAtucHlinScaleScale of Hlin.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.2.16 |
ldmAtucHlinReal1The object provides real part of Hlin for the first 256 subcarriers.
Each subcarrier takes two octets to store the value.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.4.2.17 |
ldmAtucHlinReal2The object provides real part of Hlin for the last 256 subcarriers.
Each subcarrier takes two octets to store the value.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.4.2.18 |
ldmAtucHlinImage1The object provides image part of Hlin for the first 256 subcarriers.
Each subcarrier takes two octets to store the value.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.4.2.19 |
ldmAtucHlinImage2The object provides image part of Hlin for the last 256 subcarriers.
Each subcarrier takes two octets to store the value.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.4.2.20 |
ldmAtucHlog1The object provides Hlog for the first 256 subcarriers.
Each subcarrier takes two octets to store the value.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.4.2.21 |
ldmAtucHlog2The object provides Hlog for the last 256 subcarriers.
Each subcarrier takes two octets to store the value.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.4.2.22 |
ldmAtucQln1The object provides QLN for the first 256 subcarriers.
Each subcarrier takes two octets to store the value.
A special value 0 indicates that no measurement could
be done for the sub-carrier group.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.4.2.23 |
ldmAtucQln2The object provides QLN for the last 256 subcarriers.
Each subcarrier takes two octets to store the value.
A special value 0 indicates that no measurement could
be done for the sub-carrier group.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.4.2.24 |
ldmAtucSnr1The object provides SNR for the first 256 subcarriers.
Each subcarrier takes two octets to store the value.
A special value -32768 indicates that no measurement
could be done for the sub-carrier group.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.4.2.25 |
ldmAtucSnr2The object provides SNR for the last 256 subcarriers.
Each subcarrier takes two octets to store the value.
A special value -32768 indicates that no measurement
could be done for the sub-carrier group.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.4.2.26 |
ldmAturHlinScaleScale of Hlin.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.2.27 |
ldmAturHlinRealReal part of Hlin. Each subcarrier takes two octets to store the value.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.4.2.28 |
ldmAturHlinImageImage part of Hlin. Each subcarrier takes two octets to store the value.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.4.2.29 |
ldmAturHlogHlog of subcarrier. Each subcarrier takes two octets to store the value.
A special value -32768 indicates that no measurement could be done for
the sub-carrier group.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.4.2.30 |
ldmAturQlnQLN of subcarrier. Each subcarrier takes two octets to store the value.
A special value 0 indicates that no measurement could be done for the
sub-carrier group.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.4.2.31 |
ldmAturSnrSNR of subcarrier. Each subcarrier takes two octets to store the value.
A special value -32768 indicates that no measurement could be done for
the sub-carrier group.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.4.2.32 |
selt OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.4.3 |
seltTargetIfIndex of the port which would be performed single end loopback test.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.3.1 |
seltOpsThe manager sets the object to 1 to start the selt
and the agent clears the object to zero when selt is successfully completed.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.3.2 |
seltStatusStatus description of the selt result.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.4.3.3 |
seltCableTypeThe cable type that selt result indicates.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.4.3.4 |
seltLoopEstimateLengthFtThe estimated loop length that selt result indicates.ro INTEGER UNITS "feet" .1.3.6.1.4.1.890.1.5.13.5.4.3.5 |
seltLoopEstimateLengthMeterThe estimated loop length that selt result indicates.ro INTEGER UNITS "meter" .1.3.6.1.4.1.890.1.5.13.5.4.3.6 |
mlt OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.4.4 |
mltTargetIfIndex of the port which would be performed Metallic Link Test.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.4.1 |
mltOpsThe manager sets the object to 1 to start the mlt
and the agent clears the object to zero when mlt is successfully completed.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.4.2 |
mltOptionall : test all items
vac: test AC voltage
vdc: test DC voltage
rload: test load resistance
riso: test isolation resistance
cap: test capacitor
ren: test REN value
ring: test ring voltage
metering: test metering voltage
dialtone: test dialtone
digit: test digit
roh: test rohrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.4.4.3 |
mltForceForce test even the port is in use.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.4.4.4 |
mltResult OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.4.4.5 |
mltVacTip[Special value]:
250000016 : No result.
250000032 : Test failed.
250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set.
250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook.
250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook.
250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service.
250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook.
250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc).
250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.ro INTEGER UNITS "0.1 rms" .1.3.6.1.4.1.890.1.5.13.5.4.4.5.1 |
mltVacRing[Special value]:
250000016 : No result.
250000032 : Test failed.
250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set.
250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook.
250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook.
250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service.
250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook.
250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc).
250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.ro INTEGER UNITS "0.1 rms" .1.3.6.1.4.1.890.1.5.13.5.4.4.5.2 |
mltVacDiff[Special value]:
250000016 : No result.
250000032 : Test failed.
250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set.
250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook.
250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook.
250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service.
250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook.
250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc).
250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.ro INTEGER UNITS "0.1 rms" .1.3.6.1.4.1.890.1.5.13.5.4.4.5.3 |
mltVdcTip[Special value]:
250000016 : No result.
250000032 : Test failed.
250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set.
250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook.
250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook.
250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service.
250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook.
250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc).
250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.ro INTEGER UNITS "0.1 volt" .1.3.6.1.4.1.890.1.5.13.5.4.4.5.4 |
mltVdcRing[Special value]:
250000016 : No result.
250000032 : Test failed.
250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set.
250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook.
250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook.
250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service.
250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook.
250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc).
250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.ro INTEGER UNITS "0.1 volt" .1.3.6.1.4.1.890.1.5.13.5.4.4.5.5 |
mltVdcDiff[Special value]:
250000016 : No result.
250000032 : Test failed.
250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set.
250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook.
250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook.
250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service.
250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook.
250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc).
250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.ro INTEGER UNITS "0.1 volt" .1.3.6.1.4.1.890.1.5.13.5.4.4.5.6 |
mltRLoop[Special value]:
250000016 : No result.
250000032 : Test failed.
250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set.
250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook.
250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook.
250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service.
250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook.
250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc).
250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.ro INTEGER UNITS "0.1 ohm" .1.3.6.1.4.1.890.1.5.13.5.4.4.5.7 |
mltRtg[Special value]:
250000016 : No result.
250000032 : Test failed.
250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set.
250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook.
250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook.
250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service.
250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook.
250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc).
250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.
2147483647 : Circuit open.
0 : Circuit short or fault.ro INTEGER UNITS "0.1 ohm" .1.3.6.1.4.1.890.1.5.13.5.4.4.5.8 |
mltRrg[Special value]:
250000016 : No result.
250000032 : Test failed.
250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set.
250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook.
250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook.
250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service.
250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook.
250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc).
250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item. 2147483647 : Circuit open.
0 : Circuit short or fault.ro INTEGER UNITS "0.1 ohm" .1.3.6.1.4.1.890.1.5.13.5.4.4.5.9 |
mltRtr[Special value]:
250000016 : No result.
250000032 : Test failed.
250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set.
250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook.
250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook.
250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service.
250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook.
250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc).
250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item. 2147483647 : Circuit open.
0 : Circuit short or fault.ro INTEGER UNITS "0.1 ohm" .1.3.6.1.4.1.890.1.5.13.5.4.4.5.10 |
mltCtg[Special value]:
250000016 : No result.
250000032 : Test failed.
250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set.
250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook.
250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook.
250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service.
250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook.
250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc).
250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.ro INTEGER UNITS "10^-10 F" .1.3.6.1.4.1.890.1.5.13.5.4.4.5.11 |
mltCrg[Special value]:
250000016 : No result.
250000032 : Test failed.
250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set.
250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook.
250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook.
250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service.
250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook.
250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc).
250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.ro INTEGER UNITS "10^-10 F" .1.3.6.1.4.1.890.1.5.13.5.4.4.5.12 |
mltCtr[Special value]:
250000016 : No result.
250000032 : Test failed.
250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set.
250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook.
250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook.
250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service.
250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook.
250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc).
250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.ro INTEGER UNITS "10^-10 F" .1.3.6.1.4.1.890.1.5.13.5.4.4.5.13 |
mltRen[Special value]:
250000016 : No result.
250000032 : Test failed.
250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set.
250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook.
250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook.
250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service.
250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook.
250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc).
250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.
2147483647 : Circuit open.ro INTEGER UNITS "0.1 ren" .1.3.6.1.4.1.890.1.5.13.5.4.4.5.14 |
mltVRing[Special value]:
250000016 : No result.
250000032 : Test failed.
250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set.
250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook.
250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook.
250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service.
250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook.
250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc).
250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.ro INTEGER UNITS "0.1 volt" .1.3.6.1.4.1.890.1.5.13.5.4.4.5.15 |
mltVMetering[Special value]:
250000016 : No result.
250000032 : Test failed.
250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set.
250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook.
250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook.
250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service.
250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook.
250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc).
250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.ro INTEGER UNITS "0.1 vpeak" .1.3.6.1.4.1.890.1.5.13.5.4.4.5.16 |
mltDialToneDetectedValue List:
1 : Yes.
2 : No.
3 : Test failed
4 : No result.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.4.4.5.17 |
mltDetectedDtmfCount[Special value]:
250000016 : No result.
250000032 : Test failed.
250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set.
250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook.
250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook.
250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service.
250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook.
250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc).
250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.4.5.18 |
mltDialToneDelay[Special value]:
250000016 : No result.
250000032 : Test failed.
250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set.
250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook.
250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook.
250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service.
250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook.
250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc).
250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.ro INTEGER UNITS "0.001 sec" .1.3.6.1.4.1.890.1.5.13.5.4.4.5.19 |
mltReceiverState[Normal Value]:
1 : On hook.
2 : Off hook.
3 : circuit short or fault.
4 : circuit open.
[Special value]:
250000016 : No result.
250000032 : Test failed.
250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set.
250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook.
250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook.
250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service.
250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook.
250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc).
250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.4.4.5.20 |
mltDetectedDtmfDigitThe DTMF digit string be detected in MLT test.ro DisplayString .1.3.6.1.4.1.890.1.5.13.5.4.4.5.21 |
mltErrorMsgThe error message when fail to start MLT test.ro DisplayString .1.3.6.1.4.1.890.1.5.13.5.4.4.5.22 |
mltRelayTablePerform specified MLT relay function, or turn off
MLT relay function in specified subscriber. SEQUENCE OF MltRelayEntry .1.3.6.1.4.1.890.1.5.13.5.4.4.6 |
mltRelayEntryAn entry of mltRelayTable. MltRelayEntry .1.3.6.1.4.1.890.1.5.13.5.4.4.6.1 |
mltRelaySetBy default, relay function is turned off.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.4.4.6.1.1 |
mltRelayTimeoutRelays will be turned off automatically while the specified timer is timeout.
This object is supported by R5.01 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.4.6.1.2 |
mltRelayForceSet to 1 to force to set relays even the port is in use.
This object is supported by R5.01 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.4.6.1.3 |
mltTypeoption(All) : all(0), test vac, vdc, riso, cap(1)
option(Ring) : normal(0), start to ring(1), stop to ring(2)
option(Digit) : normal(0), user input dtmf(1)rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.4.7 |
mltCountWhen test mltOption digit(11) and mltType set to user input dtmf(1),
set the number of digit for testing.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.4.8 |
mltAbortSet the slot id of a VoIP Card to terminate MLT test on it.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.4.9 |
oamloopback OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.4.5 |
oamloopbackTargetIfIndex of the port which would be performed oamloopback test.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.5.1 |
oamloopbackOpsThe manager sets the corresponding bit value to 1 to start the oamloopback test
and the agent clears the object to zero when oamloopback test is completed.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.5.2 |
oamloopbackPacketNumberNumber of packets to be sent. 1~100000rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.5.3 |
oamloopbackPacketSizeSize of each packet. 64~1518rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.5.4 |
oamloopbackResult OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.4.5.5 |
oamloopbackRecvCntNumber of packets received.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.5.5.1 |
oamloopbackElapseTimeoamloopback test elapsed time.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.5.5.2 |
oamloopbackErrorStatusoamloopback test status.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.4.5.5.3 |
vdslldm OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.4.6 |
vdslldmTargetIfIndex of the port which would be performed vdsl ldm test.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.6.1 |
vdslldmOpsThe manager sets the object to 1 to start the vdsl ldm test
and the agent clears the object to zero when ldm test is successfully completed.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.6.2 |
vdslldmStatusStatus description of vdsl ldm test result.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.4.6.3 |
ldmVtuNeLoopAttenuationUS0Loop Attenuation at US0 band.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.6.4 |
ldmVtuNeLoopAttenuationUS1Loop Attenuation at US1 band.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.6.5 |
ldmVtuNeLoopAttenuationUS2Loop Attenuation at US2 band.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.6.6 |
ldmVtuNeLoopAttenuationUS3Loop Attenuation at US3 band.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.6.7 |
ldmVtuNeSignalAttenuationUS0Signal Attenuation at US0 band.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.6.8 |
ldmVtuNeSignalAttenuationUS1Signal Attenuation at US1 band.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.6.9 |
ldmVtuNeSignalAttenuationUS2Signal Attenuation at US2 band.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.6.10 |
ldmVtuNeSignalAttenuationUS3Signal Attenuation at US3 band.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.6.11 |
ldmVtuNeSignalMarginUS0Signal Margin at US0 band.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.6.12 |
ldmVtuNeSignalMarginUS1Signal Margin at US1 band.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.6.13 |
ldmVtuNeSignalMarginUS2Signal Margin at US2 band.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.6.14 |
ldmVtuNeSignalMarginUS3Signal Margin at US3 band.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.6.15 |
ldmVtuNeAggregateTxPowerActual Aggregate Transmit Power.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.6.16 |
ldmVtuNeAttainableBitRateAttainable Bit Rate.ro Unsigned32 UNITS "bits per second" .1.3.6.1.4.1.890.1.5.13.5.4.6.17 |
ldmVtuFeLoopAttenuationDS1Loop Attenuation at DS1 band.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.6.18 |
ldmVtuFeLoopAttenuationDS2Loop Attenuation at DS2 band.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.6.19 |
ldmVtuFeLoopAttenuationDS3Loop Attenuation at DS3 band.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.6.20 |
ldmVtuFeSignalAttenuationDS1Signal Attenuation at DS1 band.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.6.21 |
ldmVtuFeSignalAttenuationDS2Signal Attenuation at DS2 band.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.6.22 |
ldmVtuFeSignalAttenuationDS3Signal Attenuation at DS3 band.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.6.23 |
ldmVtuFeSignalMarginDS1Signal Margin at DS1 band.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.6.24 |
ldmVtuFeSignalMarginDS2Signal Margin at DS2 band.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.6.25 |
ldmVtuFeSignalMarginDS3Signal Margin at DS3 band.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.6.26 |
ldmVtuFeAggregateTxPowerActual Aggregate Transmit Power.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro INTEGER UNITS "tenth dB" .1.3.6.1.4.1.890.1.5.13.5.4.6.27 |
ldmVtuFeAttainableBitRateAttainable Bit Rate.ro Unsigned32 UNITS "bits per second" .1.3.6.1.4.1.890.1.5.13.5.4.6.28 |
ldmVtuNeHlinScaleScale of Hlin.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.6.29 |
ldmVtuNeHlinRealThe object provides real part of Hlin for the subcarriers.
Each subcarrier takes two octets to store the value.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.4.6.30 |
ldmVtuNeHlinImageThe object provides image part of Hlin for the subcarriers.
Each subcarrier takes two octets to store the value.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.4.6.31 |
ldmVtuNeHlogThe object provides Hlog for the subcarriers.
Each subcarrier takes two octets to store the value.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.4.6.32 |
ldmVtuNeQlnThe object provides QLN for the subcarriers.
Each subcarrier takes two octets to store the value.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.4.6.33 |
ldmVtuNeSnrThe object provides SNR for the subcarriers.
Each subcarrier takes two octets to store the value.
A special value -32768 indicates that no measurement
could be done for the sub-carrier group.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.4.6.34 |
ldmVtuFeHlinScaleScale of Hlin.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.6.35 |
ldmVtuFeHlinRealReal part of Hlin. Each subcarrier takes two octets to store the value.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.4.6.36 |
ldmVtuFeHlinImageImage part of Hlin. Each subcarrier takes two octets to store the value.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.4.6.37 |
ldmVtuFeHlogHlog of subcarrier. Each subcarrier takes two octets to store the value.
A special value -32768 indicates that no measurement could be done for
the sub-carrier group.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.4.6.38 |
ldmVtuFeQlnQLN of subcarrier. Each subcarrier takes two octets to store the value.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.4.6.39 |
ldmVtuFeSnrSNR of subcarrier. Each subcarrier takes two octets to store the value.
A special value -32768 indicates that no measurement could be done for
the sub-carrier group.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.4.6.40 |
ldmVtuNeHlinGroupSizeNumber of sub-carriers per group used to report the H(f) linear representation values for the
respective transmission direction. The valid values are 1, 2, 4 and 8.
This object is supported by R5.02 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.6.41 |
ldmVtuFeHlinGroupSizeNumber of sub-carriers per group used to report the H(f) linear representation values for the
respective transmission direction. The valid values are 1, 2, 4 and 8.
This object is supported by R5.02 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.6.42 |
ldmVtuNeHlogGroupSizeNumber of sub-carriers per group used to report the H(f) linear representation values for the
respective transmission direction. The valid values are 1, 2, 4 and 8.
This object is supported by R5.02 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.6.43 |
ldmVtuFeHlogGroupSizeNumber of sub-carriers per group used to report the H(f) linear representation values for the
respective transmission direction. The valid values are 1, 2, 4 and 8.
This object is supported by R5.02 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.6.44 |
ldmVtuNeQlnGroupSizeNumber of sub-carriers per group used to report the Quiet Line Noise values for the
respective transmission direction. The valid values are 1, 2, 4 and 8.
This object is supported by R5.02 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.6.45 |
ldmVtuFeQlnGroupSizeNumber of sub-carriers per group used to report the Quiet Line Noise values for the
respective transmission direction. The valid values are 1, 2, 4 and 8.
This object is supported by R5.02 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.6.46 |
ldmVtuNeSnrGroupSizeNumber of sub-carriers per group used to report the SNR values on the
respective transmission direction. The valid values are 1, 2, 4 and 8.
This object is supported by R5.02 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.6.47 |
ldmVtuFeSnrGroupSizeNumber of sub-carriers per group used to report the SNR values on the
respective transmission direction. The valid values are 1, 2, 4 and 8.
This object is supported by R5.02 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.6.48 |
imaOamF5Loopback OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.4.7 |
imaOamF5LoopbackTargetGroupIndexrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.7.1 |
imaOamF5LoopbackTargetVpiVPI of the virtual channel which would be performed imaOamF5Loopback test.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.7.2 |
imaOamF5LoopbackTargetVciVCI of the virtual channel which would be performed imaOamF5Loopback test.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.7.3 |
imaOamF5LoopbackTyperw Enumeration .1.3.6.1.4.1.890.1.5.13.5.4.7.4 |
imaOamF5LoopbackOpsThe manager sets the corresponding bit value to 1 to start the imaOamF5Loopback test
and the agent clears the object to zero when loopback test is successfully completed.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.4.7.5 |
imaOamF5LoopbackSegmentId16 bytes segment id.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.4.7.6 |
imaOamF5LoopbackStatusStatus description of IMA OAM F5 Loopback test result.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.4.7.7 |
xdsl2ExtStatus OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.4.8 |
xdsl2ExtSCStatusTableThe table xdsl2ExtSCStatusTable extends xdsl2SCStatusTable for
ZyXEL product. SEQUENCE OF Xdsl2ExtSCStatusEntry .1.3.6.1.4.1.890.1.5.13.5.4.8.1 |
xdsl2ExtSCStatusEntryThe table xdsl2ExtSCStatusTable contains extra subcarrier
status parameters besides those in xdsl2LineSegmentTable. Xdsl2ExtSCStatusEntry .1.3.6.1.4.1.890.1.5.13.5.4.8.1.1 |
xdsl2SCStatusActAtpActual Aggregate Transmit Power Downstream.
The total amount of transmit power delivered by the xTU-C at
the U-C reference point, at the instant of measurement. It
ranges from -310 to 310 units of 0.1 dBm (Physical values are -31
to 31 dBm).
A value of 0x7FFFFFFF (2147483647) indicates the measurement is
out of range to be represented.
This object reflects the value of the parameter following the
most recent DELT performed on the associated line. Once the DELT
process is over, the parameter no longer changes until the row is
deleted or a new DELT process is initiated.ro Integer32 (-310..310 | 2147483647) UNITS "0.1 dBm" .1.3.6.1.4.1.890.1.5.13.5.4.8.1.1.1 |
xdsl2ExtSCStatusBandTableThe table xdsl2ExtSCStatusBandTable extends xdsl2SCStatusBandTable for
ZyXEL product. SEQUENCE OF Xdsl2ExtSCStatusBandEntry .1.3.6.1.4.1.890.1.5.13.5.4.8.2 |
xdsl2ExtSCStatusBandEntryThe table xdsl2ExtSCStatusBandTable contains extra subcarrier
status parameters that are grouped per-band besides those in
xdsl2SCStatusBandTable. Xdsl2ExtSCStatusBandEntry .1.3.6.1.4.1.890.1.5.13.5.4.8.2.1 |
xdsl2SCStatusBandSnrMarginSNR Margin is the maximum increase in dB of the noise power
received at the xTU (xTU-R for a band in the downstream direction
and xTU-C for a band in the upstream direction), such that the
BER requirements are met for all bearer channels received at the
xTU. Values range from -640 to 630 in units of 0.1 dB (Physical
values are -64 to 63 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the SNR
Margin is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the SNR
Margin measurement is currently unavailable.
This object reflects the value of the parameter following the
most recent DELT performed on the associated line. Once the DELT
process is over, the parameter no longer changes until the row is
deleted or a new DELT process is initiated.ro Integer32 (-640..630 | 2147483646 | 2147483647) UNITS "0.1 dB" .1.3.6.1.4.1.890.1.5.13.5.4.8.2.1.1 |
ipconf OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.5 |
staticRoute OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.5.1 |
maxNumOfStaticRoutesThe maximum number of static routes supported by the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.5.1.1 |
staticRouteTableA table that contains information about static routes. SEQUENCE OF StaticRouteEntry .1.3.6.1.4.1.890.1.5.13.5.5.1.2 |
staticRouteEntryA list of static route entry. StaticRouteEntry .1.3.6.1.4.1.890.1.5.13.5.5.1.2.1 |
staticRouteNameThe name of the static route.ro DisplayString .1.3.6.1.4.1.890.1.5.13.5.5.1.2.1.1 |
staticRouteDestThe destination IP address of the static route.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.5.1.2.1.2 |
staticRouteMaskThe subnet mask of the static route.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.5.1.2.1.3 |
staticRouteGatewayThe gateway IP address of the static route.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.5.1.2.1.4 |
staticRouteMetricThe routing metric of the static route.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.5.1.2.1.5 |
staticRouteRowStatusThis object is used to create a new row or modify or delete an existing row
in this table. A row is activated by setting this object to `active', , and is
deactivated by setting it to 'notInService'.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.5.1.2.1.6 |
staticIp OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.5.2 |
staticIpInbandIpInband IP Address. Not immediately apply. Use staticIpOps to apply the object setting on device.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.5.2.1 |
staticIpInbandMaskInband IP Mask. Not immediately apply. Use staticIpOps to apply the object setting on device.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.5.2.2 |
staticIpInbandVlanInband IP Vlan. Not immediately apply. Use staticIpOps to apply the object setting on device.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.5.2.3 |
staticIpOutbandIpOutband IP Address. Not immediately apply. Use staticIpOps to apply the object setting on device.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.5.2.4 |
staticIpOutbandMaskOutband IP Mask. Not immediately apply. Use staticIpOps to apply the object setting on device.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.5.2.5 |
staticIpGatewayIPGateway IP Address. Not immediately apply. Use staticIpOps to apply the object setting on device.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.5.2.6 |
staticIpOpsThe manager setting will temporary saved but not set into Device.
Set value of staticIpOps to 1 to apply the setting of IpTable on device.
Set value of staticIpOps to 2 to reload the real setting of IpTable on device now.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.5.2.7 |
lcm OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.6 |
numOfChassisThe number of chassis in the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.6.1 |
chassisTableThe table which contains the chassis information in the system. SEQUENCE OF ChassisEntry .1.3.6.1.4.1.890.1.5.13.5.6.2 |
chassisEntry ChassisEntry .1.3.6.1.4.1.890.1.5.13.5.6.2.1 |
chassisIdThe Chassis ID.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.6.2.1.1 |
chassisFrameNumberThe Frame ID.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.6.2.1.2 |
chassisSerialNumberThe Chassis Serial Number.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.6.2.1.3 |
chassisNumberThe Chassis Number which is defined by the system administrator
for management purpose.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.6.2.1.4 |
chassisStatusThe current status of the chassis.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.6.2.1.5 |
slotTableThe table which contains the slot information in a chassis. SEQUENCE OF SlotEntry .1.3.6.1.4.1.890.1.5.13.5.6.3 |
slotEntry SlotEntry .1.3.6.1.4.1.890.1.5.13.5.6.3.1 |
slotIdIdentity of the slot.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.6.3.1.1 |
slotModuleTypeCard type of the plug-in card.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.6.3.1.2 |
slotModuleDescrThe descriptions of the plug-in card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.6.3.1.3 |
slotModuleFWVersionThe firmware version of the plug-in card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.6.3.1.4 |
slotModuleDriverVersionThe DSL driver of the plug-in card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.6.3.1.5 |
slotModuleModemCodeVersionThe DSL modem code version of the plug-in card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.6.3.1.6 |
slotModuleStatusThe module state of the plug-in card.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.6.3.1.7 |
slotModuleAlarmStatusThis variable indicates the alarm status of the module.
It is a bit map represented a sum, therefore, it can represent
multiple defects simultaneously. The moduleNoDefect should be set
if and only if no other flag is set.
The various bit positions are:
1 moduleNoDefect
2 moduleOverHeat
3 moduleFanRpmLow
4 moduleVoltageLow
5 moduleThermalSensorFailure
6 modulePullOut
7 powerDC48VAFailure
8 powerDC48VBFailure
9 extAlarmInputTrigger
10 moduleDown
11 mscSwitchOverOK
12 networkTopologyChange
13 macSpoof
14 cpuHigh
15 memoryUsageHigh
16 packetBufferUsageHigh
17 loopguardOccurencero INTEGER .1.3.6.1.4.1.890.1.5.13.5.6.3.1.8 |
slotModuleSerialNumberThe serial number of the plug-in card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.6.3.1.9 |
slotModuleHWVersionThe hardware version of the plug-in card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.6.3.1.10 |
slotModuleUpTimeThe time (in seconds) since the plug-in card was last re-initialized.ro INTEGER UNITS "second" .1.3.6.1.4.1.890.1.5.13.5.6.3.1.11 |
slotModuleMacAddressThe MAC Address of the plug-in card.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.6.3.1.12 |
slotModuleMacAddress2The MAC Address of the plug-in card.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.6.3.1.13 |
mscPortTableThe table contains MSC port status. SEQUENCE OF MscPortEntry .1.3.6.1.4.1.890.1.5.13.5.6.4 |
mscPortEntry MscPortEntry .1.3.6.1.4.1.890.1.5.13.5.6.4.1 |
mscPortIdIdentity of the MSC port.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.6.4.1.1 |
mscPortTypeType of the MSC port.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.6.4.1.2 |
multicast OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.7 |
igmpEnableEnable/disable IGMP protocol.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.7.1 |
staticMulticast OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.7.2 |
maxNumberOfMcastGroupsThe max number of static multicast groups supported by the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.7.2.1 |
mcastGroupTableA table that contains static multicast group information. SEQUENCE OF McastGroupEntry .1.3.6.1.4.1.890.1.5.13.5.7.2.2 |
mcastGroupEntryThe entry of multicast group table. McastGroupEntry .1.3.6.1.4.1.890.1.5.13.5.7.2.2.1 |
mcastGroupIpThe multicast IP address of the group.ro IpAddress .1.3.6.1.4.1.890.1.5.13.5.7.2.2.1.1 |
mcastGroupFixedPortsThe port list which specify the ports joining the multicast group.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.7.2.2.1.2 |
mcastGroupForbiddenPortsThe port list which specify the ports prohibited by the multicast group.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.7.2.2.1.3 |
mcastGroupRowStatusThe row status of the multicast group entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.7.2.2.1.4 |
maxNumberOfMacMcastGroupsThe maximum number of row entries that user can create in macMcastGroupTable.
This object is supported by R5.02 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.7.2.3 |
macMcastGroupTableThis table specify the static multicast group with MAC address.
This table is supported by R5.02 and later versions. SEQUENCE OF MacMcastGroupEntry .1.3.6.1.4.1.890.1.5.13.5.7.2.4 |
macMcastGroupEntryAn entry of macMcastGroupTable. MacMcastGroupEntry .1.3.6.1.4.1.890.1.5.13.5.7.2.4.1 |
macMcastGroupMacThe multicast MAC address of the group.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.7.2.4.1.1 |
macMcastGroupFixedPortsThe port list which specify the ports joining the multicast group.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.7.2.4.1.2 |
macMcastGroupRowStatusThe row status of the MAC multicast group entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.7.2.4.1.3 |
mcastInetGroupTableA table that contains static multicast group information. SEQUENCE OF McastInetGroupEntry .1.3.6.1.4.1.890.1.5.13.5.7.2.5 |
mcastInetGroupEntryThe entry of multicast group table. McastInetGroupEntry .1.3.6.1.4.1.890.1.5.13.5.7.2.5.1 |
mcastGroupInetAddrTypeThe multicast IP address type of the group.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.7.2.5.1.1 |
mcastGroupInetAddrThe multicast IP address of the group.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.7.2.5.1.2 |
mcastGroupInetFixedPortsThe port list which specify the ports joining the multicast group.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.7.2.5.1.3 |
mcastGroupInetForbiddenPortsThe port list which specify the ports prohibited by the multicast group.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.7.2.5.1.4 |
mcastGroupInetRowStatusThe row status of the multicast group entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.7.2.5.1.5 |
igmpFilter OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.7.3 |
maxNumOfIgmpFiltersThe max number of IGMP filters supported by the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.7.3.1 |
igmpFilterTableA table that contains IGMP filters. SEQUENCE OF IgmpFilterEntry .1.3.6.1.4.1.890.1.5.13.5.7.3.2 |
igmpFilterEntryThe entry of IGMP filter table. IgmpFilterEntry .1.3.6.1.4.1.890.1.5.13.5.7.3.2.1 |
igmpFilterNameThe IGMP filter name.ro DisplayString .1.3.6.1.4.1.890.1.5.13.5.7.3.2.1.1 |
igmpFilterIndexThe index which specif the filter rule.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.7.3.2.1.2 |
igmpFilterStartIpThe start IP of the filter rule.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.7.3.2.1.3 |
igmpFilterEndIpThe end IP of the filter rule.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.7.3.2.1.4 |
igmpFilterRowStatusThe row status of the IGMP filter entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.7.3.2.1.5 |
igmpFilterInetAddrTypeThe IP Address type.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.7.3.2.1.6 |
igmpFilterInetAddrStartThe start IP of the filter rule.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.7.3.2.1.7 |
igmpFilterInetAddrEndThe end IP of the filter rule.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.7.3.2.1.8 |
igmpFilterPortTableThis table specif the IGMP filter of the port. SEQUENCE OF IgmpFilterPortEntry .1.3.6.1.4.1.890.1.5.13.5.7.3.3 |
igmpFilterPortEntryAn entry in igmpFilterPortTable. IgmpFilterPortEntry .1.3.6.1.4.1.890.1.5.13.5.7.3.3.1 |
igmpFilterPortFilterNameThe IGMP filter name of the port.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.7.3.3.1.1 |
igmpfilterBatchSet OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.7.3.4 |
igmpfilterTargetThis managed object is used for identify the target on which
the port configuration should be performed. The target is encoded as:
Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7
Byte 2~4: each octet specifies a set of eight slots, with the
first octet specifying slots 1 through 8, and the second
octet specifying slots 9 through 16, and so on.
Byte 5~: each octet specifies a set of eight ports, with the first
octet specifying ports 1 through 8, etc.rw OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.7.3.4.1 |
igmpfilterOpsThe corresponding bit is set to 1 to start the operation.
The various bit positions are:
BIT 1: set IGMP filter.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.7.3.4.2 |
igmpfilterForBatchSetThe IGMP filter name.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.7.3.4.3 |
mcastBandwidth OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.7.4 |
mcastDefaultBandwidthDefault bandwidth requirement for a multicast channel.
This object is supported by R1.02 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.7.4.1 |
maxNumOfMcastBwThe maximum number of row entries that user can create in mcastBwTable.
This object is supported by R1.02 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.7.4.2 |
mcastBwTableThis table defines bandwidth budget for a range of multicast IP channels.
This table is supported by R1.02 and later versions. SEQUENCE OF McastBwEntry .1.3.6.1.4.1.890.1.5.13.5.7.4.3 |
mcastBwEntryAn entry of mcastBwTable. McastBwEntry .1.3.6.1.4.1.890.1.5.13.5.7.4.3.1 |
mcastBwIndexThe index which specify the entry.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.7.4.3.1.1 |
mcastBwStartIpThe start multicast IP of the bandwidth control range.ro IpAddress .1.3.6.1.4.1.890.1.5.13.5.7.4.3.1.2 |
mcastBwEndIpThe end multicast IP of the bandwidth control range.ro IpAddress .1.3.6.1.4.1.890.1.5.13.5.7.4.3.1.3 |
mcastBwBandwidthThe bandwidth budget for the multicast IP channels.rw INTEGER UNITS "Kbps" .1.3.6.1.4.1.890.1.5.13.5.7.4.3.1.4 |
mcastBwRowStatusThe row status of the entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.7.4.3.1.5 |
mcastBwPortTableThis table specify the multicast bandwidth control of the port.
This table is supported by R1.02 and later versions. SEQUENCE OF McastBwPortEntry .1.3.6.1.4.1.890.1.5.13.5.7.4.4 |
mcastBwPortEntryAn entry of mcastBwPortTable. McastBwPortEntry .1.3.6.1.4.1.890.1.5.13.5.7.4.4.1 |
mcastBwPortEnableEnable/disable multicast bandwidth control for a port.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.7.4.4.1.1 |
mcastBwPortBandwidthSet bandwidth threshold for a port.rw INTEGER UNITS "Kbps" .1.3.6.1.4.1.890.1.5.13.5.7.4.4.1.2 |
mcastBwInetTableThis table defines bandwidth budget for a range of multicast IP channels for IPv6.
This table is supported by R5.06 and later versions. SEQUENCE OF McastBwInetEntry .1.3.6.1.4.1.890.1.5.13.5.7.4.5 |
mcastBwInetEntryAn entry of mcastBwInetTable. McastBwInetEntry .1.3.6.1.4.1.890.1.5.13.5.7.4.5.1 |
mcastBwInetIndexThe index which specify the entry.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.7.4.5.1.1 |
mcastBwInetAddrTypeThe ip address type of multicast IP.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.7.4.5.1.2 |
mcastBwInetAddrStartThe start multicast IP of the bandwidth control range.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.7.4.5.1.3 |
mcastBwInetAddrEndThe end multicast IP of the bandwidth control range.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.7.4.5.1.4 |
mcastBwInetBandwidthThe bandwidth budget for the multicast IP channels.rw INTEGER UNITS "Kbps" .1.3.6.1.4.1.890.1.5.13.5.7.4.5.1.5 |
mcastBwInetRowStatusThe row status of the entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.7.4.5.1.6 |
igmpCount OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.7.5 |
igmpCountPortTableThis table specify the IGMP count limiting of the port.
This table is supported by R1.02 and later versions. SEQUENCE OF IgmpCountPortEntry .1.3.6.1.4.1.890.1.5.13.5.7.5.1 |
igmpCountPortEntryAn entry of igmpCountPortTable. IgmpCountPortEntry .1.3.6.1.4.1.890.1.5.13.5.7.5.1.1 |
igmpCountPortEnableEnable/disable IGMP count limiting for a port.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.7.5.1.1.1 |
igmpCountPortLimitThe maximum allowed IGMP report count for a port.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.7.5.1.1.2 |
igmpMessageCountPortTableThis table specify the IGMP message count limiting of the port. SEQUENCE OF IgmpMessageCountPortEntry .1.3.6.1.4.1.890.1.5.13.5.7.5.2 |
igmpMessageCountPortEntryAn entry of igmpMessageCountPortTable. IgmpMessageCountPortEntry .1.3.6.1.4.1.890.1.5.13.5.7.5.2.1 |
igmpMessageCountPortEnableEnable/disable IGMP message count limiting for a port.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.7.5.2.1.1 |
igmpMessageCountPortLimitThe maximum allowed IGMP message count for a port.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.7.5.2.1.2 |
mvlan OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.7.6 |
maxNumOfMvlanThe maximum number of row entries that user can create in mvlanTable.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.7.6.1 |
mvlanTableA table containing static configuration information for
each multicast VLAN configured into the device. SEQUENCE OF MvlanEntry .1.3.6.1.4.1.890.1.5.13.5.7.6.2 |
mvlanEntryAn entry of mvlanTable. MvlanEntry .1.3.6.1.4.1.890.1.5.13.5.7.6.2.1 |
mvlanIndexThe VLAN-ID refering to this VLAN.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.7.6.2.1.1 |
mvlanNameAn administratively assigned string, which may be used to identify the VLAN.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.7.6.2.1.2 |
mvlanEgressPortsThe set of ports which are permanently assigned to the
egress list for this multicast VLAN.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.7.6.2.1.3 |
mvlanRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.7.6.2.1.4 |
mvlan8021pPriorityrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.7.6.2.1.5 |
mvlanTranslateTableA table that contains multicast to VLAN translation. SEQUENCE OF MvlanTranslateEntry .1.3.6.1.4.1.890.1.5.13.5.7.6.3 |
mvlanTranslateEntryAn entry of mvlanTranslateTable. MvlanTranslateEntry .1.3.6.1.4.1.890.1.5.13.5.7.6.3.1 |
mvlanTranslateIndexThe index which specif the entry.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.7.6.3.1.1 |
mvlanTranslateStartIpThe start IP of the multicast VLAN translation.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.7.6.3.1.2 |
mvlanTranslateEndIpThe end IP of the multicast VLAN translation.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.7.6.3.1.3 |
mvlanTranslateInetAddrTypeThe IP Address type.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.7.6.3.1.4 |
mvlanTranslateInetAddrStartThe start IP of the multicast VLAN translation.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.7.6.3.1.5 |
mvlanTranslateInetAddrEndThe end IP of the multicast VLAN translation.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.7.6.3.1.6 |
mvlanExtTableA table that contains MVLAN. SEQUENCE OF MvlanExtEntry .1.3.6.1.4.1.890.1.5.13.5.7.6.4 |
mvlanExtEntryAn entry of mvlanExtTable. MvlanExtEntry .1.3.6.1.4.1.890.1.5.13.5.7.6.4.1 |
mvlanExtRegEgress or forbid to the Multicast VLAN.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.7.6.4.1.1 |
mvlanExtCvidCustomer VLANrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.7.6.4.1.2 |
mvlanNonmemberPortset this object to 'discard' so that the system discards IGMP/MLD reports
if the subscriber port is not a member of the MVLAN which the group address belong to.
Set to 'pass' so that the system accepts such IGMP/MLD reports and process them with the original VLAN.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.7.6.5 |
queryVid OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.7.7 |
maxNumOfQryVidThe maximum number of row entries that user can create in qryVidConfTable.
This object is supported by R1.02 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.7.7.1 |
qryVidConfTableThis table defines statically set VLANs used for response IGMP report.
This table is supported by R1.02 and later versions. SEQUENCE OF QryVidConfEntry .1.3.6.1.4.1.890.1.5.13.5.7.7.2 |
qryVidConfEntryAn entry in qryVidConfTable. QryVidConfEntry .1.3.6.1.4.1.890.1.5.13.5.7.7.2.1 |
qryVidVLAN ID.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.7.7.2.1.1 |
qryVidRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.7.7.2.1.2 |
qryVidStatusTableThis table shows statically set or dynamically learned VLANs used for response IGMP report. SEQUENCE OF QryVidStatusEntry .1.3.6.1.4.1.890.1.5.13.5.7.7.3 |
qryVidStatusEntryAn entry in qryVidStatusTable. QryVidStatusEntry .1.3.6.1.4.1.890.1.5.13.5.7.7.3.1 |
qryVidTypeVLAN type.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.7.7.3.1.1 |
igmpModeSetting IGMP with aggresive mode will issue an IGMP report from new active port
when topology change occurs, while normal mode won't.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.7.8 |
igmpVersionSetting IGMP version. This object is supported by R3.00 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.7.9 |
igmpFastLeaveEnablerw Enumeration .1.3.6.1.4.1.890.1.5.13.5.7.10 |
igmpFastLeaveTimerrw INTEGER UNITS "second" .1.3.6.1.4.1.890.1.5.13.5.7.11 |
unknownMulticastrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.7.12 |
ipv6PassThroughSet IPv6 packet transparent passthrough.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.7.13 |
reservedGroupSet reserved packets transparent passthrougthrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.7.14 |
igmpHistoryTableThis table contains multicast IGMP/MLD history configuration. SEQUENCE OF IgmpHistoryEntry .1.3.6.1.4.1.890.1.5.13.5.7.15 |
igmpHistoryEntryThe entry of multicast igmp history table. IgmpHistoryEntry .1.3.6.1.4.1.890.1.5.13.5.7.15.1 |
igmphistoryenableEnable/disable IGMP/MLD multicast group join/leave history logging.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.7.15.1.1 |
port OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8 |
subrPortTableThis table includes subscriber attributes for the port. SEQUENCE OF SubrPortEntry .1.3.6.1.4.1.890.1.5.13.5.8.1 |
subrPortEntryAn entry in subrPortTable. SubrPortEntry .1.3.6.1.4.1.890.1.5.13.5.8.1.1 |
subrPortNameName of the subscriber.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.1.1.1 |
subrPortTelTelephone number of the subscriber.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.1.1.2 |
subrPortMdfMDF information of this subscriber portrw DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.1.1.3 |
adslPort OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.2 |
adslLineConfTableThis table includes common attributes describing the ADSL line. SEQUENCE OF AdslLineConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.2.1 |
adslLineConfEntryAn entry in adslLineConfTable. AdslLineConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.2.1.1 |
adslLineConfAdslModeG.lite and T1.413 are only applicable to annex A board.
ETSI is only applicable to annex B board.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.2.1.1.1 |
adslLineConfAnnexLEnable/disable annex L for the port.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.2.1.1.2 |
adslLineConfAnnexMEnable/disable annex M for the port.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.2.1.1.3 |
adslLineConfAnnexIEnable/disable annex I for the port.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.2.1.1.4 |
adslLineConfOptionMaskThe semantic for each bit is:
BIT 1 : Disable Trellis
BIT 2 : Disable Reed-Solomon
BIT 3 : Disable upstream bitswap
BIT 4 : Disable downstream bitswap
BIT 5 : Disable 1-bit constellation
BIT 6 : Disable transmit windowing
BIT 7 : Disable s=0.5 support (ADSL1 only)
BIT 8 : Disable G.lite rate limit (ADSL1 only)
BIT 9 : Disable Nitro moderw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.2.1.1.5 |
adslLineConfPowerMgmtEnable/disable power management for the port.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.2.1.1.6 |
adslLineConfPowerModeThe power mode of the ADSL line.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.2.1.1.7 |
adslLineConfAturMaxTxPowerThe maximum allowed transmit power of ATU-R.rw INTEGER (-130..200) UNITS "tenth dBm" .1.3.6.1.4.1.890.1.5.13.5.8.2.1.1.8 |
adslLineConfAtucMaxTxPowerThe maximum allowed transmit power of ATU-C.rw INTEGER (-50..200) UNITS "tenth dBm" .1.3.6.1.4.1.890.1.5.13.5.8.2.1.1.9 |
adslLineConfMaxRxPowerThe maximum aggregate received power.rw INTEGER (-255..255) UNITS "tenth dBm" .1.3.6.1.4.1.890.1.5.13.5.8.2.1.1.10 |
adslLineConfAturCarrierMaskThe upstream carrier mask from bin 0 to 63. Bit set to 1 indicates
the bin is masked off.rw OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.8.2.1.1.11 |
adslLineConfAtucCarrierMask0The downstream carrier mask from bin 32 to 255. Bit set to 1 indicates
the bin is masked off.rw OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.8.2.1.1.12 |
adslLineConfAtucCarrierMask1The downstream carrier mask from bin 256 to 511. Bit set to 1 indicates
the bin is masked off.rw OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.8.2.1.1.13 |
adslLineConfAturInpThe upstream Impulse Noise Protection minimum setting in unit of DMT symbol.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.2.1.1.14 |
adslLineConfAtucInpThe downstream Impulse Noise Protection minimum setting in unit of DMT symbol.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.2.1.1.15 |
bitLoad OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.2.2 |
bitLoadTableThis table provides the number of bits per carrier for each ADSL port. SEQUENCE OF BitLoadEntry .1.3.6.1.4.1.890.1.5.13.5.8.2.2.1 |
bitLoadEntryAn entry in bitLoadTable. BitLoadEntry .1.3.6.1.4.1.890.1.5.13.5.8.2.2.1.1 |
bitLoadBitsThis object provides the number of bits for all carriers in the port.
The first octet specify the number of bits for carrier 1, and the second
octet specify the number of bits for carrier 2, and so on.
The object provides the number of bits for carrier 1 to 512.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.8.2.2.1.1.1 |
bitLoadAtucNumOfCarriersThe number of carriers for ATU-C.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.2.2.1.1.2 |
bitLoadAturNumOfCarriersThe number of carriers for ATU-R.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.2.2.1.1.3 |
adslPortBatchSet OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.2.3 |
adslPortTargetThe managed object is used for identify the target on which
the port configuration should be performed. The target is encoded as:
Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7
Byte 2~4: each octet specifies a set of eight slots, with the
first octet specifying slots 1 through 8, and the second
octet specifying slots 9 through 16, and so on.
Byte 5~: each octet specifies a set of eight ports, with the first
octet specifying ports 1 through 8, etc.rw OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.8.2.3.1 |
adslPortOpsThe managed object is for ADSL line configuration. When the EMS
wants to issue the desired operation, the EMS shall send SNMP-SET message to set
the corresponding bit value to be 1. The various bit positions are:
BIT 1: enable port
BIT 2: disable port
BIT 3: set ADSL mode
BIT 4: set line profile
BIT 5: set alarm profile
BIT 6: enable Annex L to be narrow mode
BIT 7: enable Annex L to be wide mode
BIT 8: disable Annex L
BIT 9: enable Annex M
BIT 10: disable Annex M
BIT 11: enable Annex I
BIT 12: disable Annex I
BIT 13: set option mask
BIT 14: enable power management mode to be L2
BIT 15: enable power management mode to be L3
BIT 16: disable power management mode
BIT 17: set power mode to be fixed
BIT 18: set power mode to be priority to power
BIT 19: set power mode to be priority to rate
BIT 20: set ATU-R max Tx power
BIT 21: set ATU-C max Tx power
BIT 22: set max Rx power
BIT 23: set ATU-R carrier mask
BIT 24: set ATU-C carrier mask
BIT 25: set ATU-R INP minimum setting
BIT 26: set ATU-C INP minimum settingrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.2.3.2 |
adslModeForBatchSetG.lite and T1.413 are only applicable to annex A board.
ETSI is only applicable to annex B board.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.2.3.3 |
adslLineProfileForBatchSetThe ADSL line profile.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.2.3.4 |
adslAlarmProfileForBatchSetThe ADSL alarm profile.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.2.3.5 |
adslOptionMaskForBatchSetThe semantic for each bit is identical to the object adslLineConfOptionMask.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.2.3.6 |
adslAturMaxTxPowerForBatchSetThe maximum allowed transmit power of ATU-R.rw INTEGER (-130..200) UNITS "tenth dBm" .1.3.6.1.4.1.890.1.5.13.5.8.2.3.7 |
adslAtucMaxTxPowerForBatchSetThe maximum allowed transmit power of ATU-C.rw INTEGER (-50..200) UNITS "tenth dBm" .1.3.6.1.4.1.890.1.5.13.5.8.2.3.8 |
adslMaxRxPowerForBatchSetThe maximum aggregate received power.rw INTEGER (-255..255) UNITS "tenth dBm" .1.3.6.1.4.1.890.1.5.13.5.8.2.3.9 |
adslAturCarrierMaskForBatchSetThe upstream carrier mask from bin 0 to 63. Bit set to 1 indicates
the bin is masked off.rw OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.8.2.3.10 |
adslAtucCarrierMask0ForBatchSetThe downstream carrier mask from bin 32 to 255. Bit set to 1 indicates
the bin is masked off.rw OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.8.2.3.11 |
adslAtucCarrierMask1ForBatchSetThe downstream carrier mask from bin 256 to 511. Bit set to 1 indicates
the bin is masked off.rw OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.8.2.3.12 |
adslAturInpForBatchSetThe upstream Impulse Noise Protection minimum setting in unit of DMT symbol.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.2.3.13 |
adslAtucInpForBatchSetThe downstream Impulse Noise Protection minimum setting in unit of DMT symbol.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.2.3.14 |
adslLineStatusTableThis table includes the ADSL line status. SEQUENCE OF AdslLineStatusEntry .1.3.6.1.4.1.890.1.5.13.5.8.2.4 |
adslLineStatusEntryAn entry in adslLineStatusTable. AdslLineStatusEntry .1.3.6.1.4.1.890.1.5.13.5.8.2.4.1 |
adslLineStatusModeThe link up mode of the ADSL line.
The following items is added from R5.05
8: adsl2Annexi(8)
9: adsl2Annexl(9)
10: adsl2AnnexlNarrow(10)
11: adsl2Annexm(11)
12: adsl2PlusAnnexi(12)
13: adsl2PlusAnnexm(13)ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.2.4.1.1 |
adslLineStatusUpTimeThe time since the ADSL line link up.ro Unsigned32 UNITS "second" .1.3.6.1.4.1.890.1.5.13.5.8.2.4.1.2 |
adslLineStatusAturInpThe upstream Impulse Noise Protection in unit of 0.1 DMT symbol.ro INTEGER UNITS "0.1 DMT symbol" .1.3.6.1.4.1.890.1.5.13.5.8.2.4.1.3 |
adslLineStatusAtucInpThe downstream Impulse Noise Protection in unit of 0.1 DMT symbol.ro INTEGER UNITS "0.1 DMT symbol" .1.3.6.1.4.1.890.1.5.13.5.8.2.4.1.4 |
powerMgmtParamTableThis table defines L0 to L2 power transition parameters.
This table is supported by R1.02 and later versions. SEQUENCE OF PowerMgmtParamEntry .1.3.6.1.4.1.890.1.5.13.5.8.2.5 |
powerMgmtParamEntryAn entry in powerMgmtParamTable. PowerMgmtParamEntry .1.3.6.1.4.1.890.1.5.13.5.8.2.5.1 |
powerMgmtL0TimeThe object specifies the minimum time in L0 mode before L2 mode may be entered.rw INTEGER UNITS "second" .1.3.6.1.4.1.890.1.5.13.5.8.2.5.1.1 |
powerMgmtL2TimeThe object specifies the minimum time in L2 mode before trimming and in between power trims.rw INTEGER UNITS "second" .1.3.6.1.4.1.890.1.5.13.5.8.2.5.1.2 |
powerMgmtL2AtprThe maximum aggregate transmit power.rw INTEGER UNITS "dB" .1.3.6.1.4.1.890.1.5.13.5.8.2.5.1.3 |
powerMgmtL2AtprtThe maximum total aggregate transmit power.rw INTEGER UNITS "dB" .1.3.6.1.4.1.890.1.5.13.5.8.2.5.1.4 |
powerMgmtL2MinRateThe object specifies the minimum L2 rate.rw INTEGER UNITS "Kbps" .1.3.6.1.4.1.890.1.5.13.5.8.2.5.1.5 |
powerMgmtL2MaxRateThe object specifies the maximum L2 rate.rw INTEGER UNITS "Kbps" .1.3.6.1.4.1.890.1.5.13.5.8.2.5.1.6 |
powerMgmtL2ThreshRateThe object specifies the rate threshold that triggers the line entering L0 or L2 mode.rw INTEGER UNITS "percentage" .1.3.6.1.4.1.890.1.5.13.5.8.2.5.1.7 |
powerMgmtPSDTableThis table provides the PSD setting for both ATU-C and ATU-R.
This table is supported by R1.02 and later versions. SEQUENCE OF PowerMgmtPSDEntry .1.3.6.1.4.1.890.1.5.13.5.8.2.6 |
powerMgmtPSDEntryAn entry in powerMgmtPSDTable. PowerMgmtPSDEntry .1.3.6.1.4.1.890.1.5.13.5.8.2.6.1 |
powerMgmtAtucMaxPSDThe object specifies the maximum ATU-C PSD.rw INTEGER UNITS "0.1dBm/Hz" .1.3.6.1.4.1.890.1.5.13.5.8.2.6.1.1 |
powerMgmtAturMaxPSDThe object specifies the maximum ATU-R PSD.rw INTEGER UNITS "0.1dBm/Hz" .1.3.6.1.4.1.890.1.5.13.5.8.2.6.1.2 |
shdslPort OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.3 |
shdslLineConfTableThis table includes common attributes describing the SHDSL line. SEQUENCE OF ShdslLineConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.3.1 |
shdslLineConfEntryAn entry in shdslLineConfTable. ShdslLineConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.3.1.1 |
shdslLineConfShdslModeMode of the SHDSL port. This MIB object is not supported by R5.03 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.3.1.1.1 |
shdslLineConfPmmsNegotiated noise margin mode of the SHDSL port.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.3.1.1.2 |
shdslLineConfPboModePower backoff mode of the SHDSL port.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.3.1.1.3 |
shdslLineConfPboValuePower backoff value of the SHDSL port.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.3.1.1.4 |
shdslLineConfModulationModulation mode of the SHDSL port. This MIB object is supported by R5.03 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.3.1.1.5 |
shdslLineConfTCModeTransmission Convergence layer. This MIB object is supported by R5.05 and later versions.
1: atm
2: efmrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.3.1.1.6 |
shdslPortBatchSet OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.3.2 |
shdslPortTargetThe managed object is used for identify the target on which
the port configuration should be performed. The target is encoded as:
Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7
Byte 2~4: each octet specifies a set of eight slots, with the
first octet specifying slots 1 through 8, and the second
octet specifying slots 9 through 16, and so on.
Byte 5~: each octet specifies a set of eight ports, with the first
octet specifying ports 1 through 8, etc.rw OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.8.3.2.1 |
shdslPortOpsThe managed object is for SHDSL line configuration. When the EMS
wants to issue the desired operation, the EMS shall send SNMP-SET message to set
the corresponding bit value to be 1. The various bit positions are:
BIT 1: enable port
BIT 2: disable port
BIT 3: set SHDSL mode
BIT 4: set line profile
BIT 5: set alarm profile
BIT 6: set pmms mode to be normal
BIT 7: set pmms mode to be forced
BIT 8: set pbo mode to be normal-epl
BIT 9: set pbo mode to be forced-epl
BIT 10: set pbo mode to be forced-no-epl
BIT 11: set pbo valuerw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.3.2.2 |
shdslModeForBatchSetMode of the SHDSL port.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.3.2.3 |
shdslLineProfileForBatchSetThe SHDSL line profile.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.3.2.4 |
shdslAlarmProfileForBatchSetThe SHDSL alarm profile.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.3.2.5 |
shdslPboValueForBatchSetPower backoff value of the SHDSL port.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.3.2.6 |
shdslLineStatusTableThis table includes the SHDSL line status. SEQUENCE OF ShdslLineStatusEntry .1.3.6.1.4.1.890.1.5.13.5.8.3.3 |
shdslLineStatusEntryAn entry in shdslLineStatusTable. ShdslLineStatusEntry .1.3.6.1.4.1.890.1.5.13.5.8.3.3.1 |
shdslLineStatusWirePairThe link-up wire pair of the SHDSL line.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.3.3.1.1 |
pvc OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.4 |
maxNumOfPvcsThe maximum number of PVCs which could be created on a port.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.4.1 |
pvcTableThis table includes PVC configuration. SEQUENCE OF PvcEntry .1.3.6.1.4.1.890.1.5.13.5.8.4.2 |
pvcEntryAn entry in pvcTable. PvcEntry .1.3.6.1.4.1.890.1.5.13.5.8.4.2.1 |
pvcVpiVPI of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.4.2.1.1 |
pvcVciVCI of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.4.2.1.2 |
pvcPvidDefault VID of the pvc.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.8.4.2.1.3 |
pvcEncapEncapsulation of the pvc.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.4.2.1.4 |
pvcPriority802.1p default priority of the pvc.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.4.2.1.5 |
pvcProfileThe value of this object identifies the row in the atmProfileTable, which applies for this pvc.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.4.2.1.6 |
pvcRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.4.2.1.7 |
pvcMvlanEnableEnable/disable multicast VLAN function for the PVC.
This object is supported by R1.02 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.4.2.1.8 |
pvcAcNameAccess concentrator name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.4.2.1.9 |
pvcServiceNameService name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.4.2.1.10 |
pvcHelloTimeThe system will close the PVC if there are not any LCP echo messages passed through
during the LCP hello time.rw INTEGER UNITS "second" .1.3.6.1.4.1.890.1.5.13.5.8.4.2.1.11 |
pvcVlanTableThis table includes the VLAN configuration for each PVC. SEQUENCE OF PvcVlanEntry .1.3.6.1.4.1.890.1.5.13.5.8.4.3 |
pvcVlanEntryAn entry in pvcVlanTable. PvcVlanEntry .1.3.6.1.4.1.890.1.5.13.5.8.4.3.1 |
pvcVlanRegThe PVC is egress or forbidden for this VLAN.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.4.3.1.1 |
pvcVlanTagThe PVC should transmit egress packets for this VLAN as tagged or untagged.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.4.3.1.2 |
pvcVlanRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.4.3.1.3 |
pvcUsRateLimitTableThis table defines the upstream rate limit for each PVC.
This table is supported by R1.03 and later versions. SEQUENCE OF PvcUsRateLimitEntry .1.3.6.1.4.1.890.1.5.13.5.8.4.4 |
pvcUsRateLimitEntryAn entry in pvcUsRateLimitTable. PvcUsRateLimitEntry .1.3.6.1.4.1.890.1.5.13.5.8.4.4.1 |
pvcUsRateLimitEnableEnable/disable upstream rate limit for a PVC.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.4.4.1.1 |
pvcUsRateLimitUpstream rate limit in Kbps for a PVC.rw INTEGER UNITS "Kbps" .1.3.6.1.4.1.890.1.5.13.5.8.4.4.1.2 |
ppvc OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.5 |
maxNumOfPriorityPvcsThe maximum number of priority PVCs which could be created on a port.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.5.1 |
ppvcTableThis table includes priority PVC configuration. SEQUENCE OF PpvcEntry .1.3.6.1.4.1.890.1.5.13.5.8.5.2 |
ppvcEntryAn entry in ppvcTable. PpvcEntry .1.3.6.1.4.1.890.1.5.13.5.8.5.2.1 |
ppvcVpiVPI of the ppvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.5.2.1.1 |
ppvcVciVCI of the ppvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.5.2.1.2 |
ppvcPvidDefault VID of the ppvc.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.8.5.2.1.3 |
ppvcEncapEncapsulation of the ppvc.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.5.2.1.4 |
ppvcPriority802.1p default priority of the ppvc.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.5.2.1.5 |
ppvcRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.5.2.1.6 |
ppvcVlanTableThis table includes the VLAN configuration for each priority PVC. SEQUENCE OF PpvcVlanEntry .1.3.6.1.4.1.890.1.5.13.5.8.5.3 |
ppvcVlanEntryAn entry in ppvcVlanTable. PpvcVlanEntry .1.3.6.1.4.1.890.1.5.13.5.8.5.3.1 |
ppvcVlanRegThe PVC is egress or forbidden for this VLAN.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.5.3.1.1 |
ppvcVlanTagThe PVC should transmit egress packets for this VLAN as tagged or untagged.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.5.3.1.2 |
ppvcVlanRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.5.3.1.3 |
ppvcMemberTableThis table includes priority PVC member configuration. SEQUENCE OF PpvcMemberEntry .1.3.6.1.4.1.890.1.5.13.5.8.5.4 |
ppvcMemberEntryAn entry in ppvcMemberTable. PpvcMemberEntry .1.3.6.1.4.1.890.1.5.13.5.8.5.4.1 |
ppvcMemberVpiVPI of the member ppvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.5.4.1.1 |
ppvcMemberVciVCI of the member ppvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.5.4.1.2 |
ppvcMemberPriority802.1p default priority of the member ppvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.5.4.1.3 |
ppvcMemberProfileThe profile of the member ppvc.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.5.4.1.4 |
ppvcMemberRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.5.4.1.5 |
portOperation OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.6 |
portTargetThe managed object is used for identify the target on which
the port configuration should be performed. The target is encoded as:
Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7
Byte 2~4: each octet specifies a set of eight slots, with the
first octet specifying slots 1 through 8, and the second
octet specifying slots 9 through 16, and so on.
Byte 5~: each octet specifies a set of eight ports, with the first
octet specifying ports 1 through 8, etc.rw OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.8.6.1 |
portOpsThe managed object is for xDSL line configuration. When the EMS
wants to issue the desired operation, the EMS shall send SNMP-SET message to set
the corresponding bit value to be 1. The various bit positions are:
BIT 1: enable port
BIT 2: disable port
BIT 3: reserved
BIT 4: default port settingsrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.6.2 |
pvcStats OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.7 |
pvcStatsTableThis table includes PVC statistics. SEQUENCE OF PvcStatsEntry .1.3.6.1.4.1.890.1.5.13.5.8.7.1 |
pvcStatsEntryAn entry in pvcStatsTable. PvcStatsEntry .1.3.6.1.4.1.890.1.5.13.5.8.7.1.1 |
pvcStatsTxRateTransmission Rate (byte/sec) on the PVC.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.7.1.1.1 |
pvcStatsRxRateReceive rate (byte/sec) on the PVC.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.7.1.1.2 |
pvcStatsTxCellsThe number of transmitted cells on the PVC since last counter reset.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.8.7.1.1.3 |
pvcStatsRxCellsThe number of received packets on the PVC since last counter reset.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.8.7.1.1.4 |
pvcStatsCrcErrorsThe number of detected CRC errors on the PVC since last counter reset.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.8.7.1.1.5 |
pvcStatsTxPacketsThis object is supported by R1.02 and later versions.
The number of transmitted packets on the PVC since last counter reset.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.8.7.1.1.6 |
pvcStatsRxPacketsThis object is supported by R1.02 and later versions.
The number of received packets on the PVC since last counter reset.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.8.7.1.1.7 |
pvcStatsTxUnicastThis object is supported by R1.02 and later versions.
The number of transmitted unicast packets on the PVC since last counter reset.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.8.7.1.1.8 |
pvcStatsRxUnicastThis object is supported by R1.02 and later versions.
The number of received unicast packets on the PVC since last counter reset.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.8.7.1.1.9 |
pvcStatsTxMulticastThis object is supported by R1.02 and later versions.
The number of transmitted multicast packets on the PVC since last counter reset.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.8.7.1.1.10 |
pvcStatsRxMulticastThis object is supported by R1.02 and later versions.
The number of received multicast packets on the PVC since last counter reset.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.8.7.1.1.11 |
pvcStatsTxBroadcastThis object is supported by R1.02 and later versions.
The number of transmitted broadcast packets on the PVC since last counter reset.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.8.7.1.1.12 |
pvcStatsRxBroadcastThis object is supported by R1.02 and later versions.
The number of received broadcast packets on the PVC since last counter reset.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.8.7.1.1.13 |
pvcStatsTxDiscardThis object is supported by R1.02 and later versions.
The number of discarded packets when transmitted on the PVC since last counter reset.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.8.7.1.1.14 |
pvcStatsRxDiscardThis object is supported by R1.02 and later versions.
The number of discarded packets when received on the PVC since last counter reset.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.8.7.1.1.15 |
pvcCounterIfIndexIfIndex of the PVC whose counters would be reset.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.7.2 |
pvcCounterVpiVPI of the PVC whose counters would be reset.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.7.3 |
pvcCounterVciVCI of the PVC whose counters would be reset.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.7.4 |
pvcCounterResetSet the object to 1 to reset PVC counters for the PVC which is identified by
pvcCounterIfIndex, pvcCounterVpi, and pvcCounterVci.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.7.5 |
paepvc OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.8 |
paepvcTableThis table includes PPPoAoE PVC configuration.
This table is supported by R1.02 and later versions. SEQUENCE OF PaepvcEntry .1.3.6.1.4.1.890.1.5.13.5.8.8.1 |
paepvcEntryAn entry of paepvcTable. PaepvcEntry .1.3.6.1.4.1.890.1.5.13.5.8.8.1.1 |
paepvcVpiVPI of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.8.1.1.1 |
paepvcVciVCI of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.8.1.1.2 |
paepvcPvidDefault VID of the pvc.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.8.8.1.1.3 |
paepvcEncapEncapsulation of the pvc.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.8.1.1.4 |
paepvcPriority802.1p default priority of the pvc.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.8.1.1.5 |
paepvcProfileThe value of this object identifies the row in the atmProfileTable, which applies for this pvc.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.8.1.1.6 |
paepvcAcNameAccess concentrator name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.8.1.1.7 |
paepvcServiceNameService name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.8.1.1.8 |
paepvcHelloTimeThe system will close the PVC if there are not any LCP echo messages passed through
during the LCP hello time.rw INTEGER UNITS "second" .1.3.6.1.4.1.890.1.5.13.5.8.8.1.1.9 |
paepvcRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.8.1.1.10 |
tlspvc OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.9 |
tlspvcTableThis table includes Transparent LAN Service (TLS) PVC configuration.
This table is supported by R1.02 and later versions. SEQUENCE OF TlspvcEntry .1.3.6.1.4.1.890.1.5.13.5.8.9.1 |
tlspvcEntryAn entry of tlspvcTable. TlspvcEntry .1.3.6.1.4.1.890.1.5.13.5.8.9.1.1 |
tlspvcVpiVPI of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.9.1.1.1 |
tlspvcVciVCI of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.9.1.1.2 |
tlspvcSvids-tag VLAN ID of the pvc.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.8.9.1.1.3 |
tlspvcEncapEncapsulation of the pvc.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.9.1.1.4 |
tlspvcSprioritys-tag priority of the pvc.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.9.1.1.5 |
tlspvcProfileThe value of this object identifies the row in the atmProfileTable, which applies for this pvc.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.9.1.1.6 |
tlspvcRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.9.1.1.7 |
vdslPort OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.10 |
vdslLineConfTableThis table includes common attributes describing the VDSL line.
This table is supported by R2.00 and later versions. SEQUENCE OF VdslLineConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.10.1 |
vdslLineConfEntryAn entry in vdslLineConfTable. VdslLineConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1 |
vdslLineConfUpboEnable/disable upstream power backoff control.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.1 |
vdslLineConfVdslProfileSet VDSL profile.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.2 |
vdslLineConfFrequencyPlanSet VDSL frequency plan.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.3 |
vdslLineConfRfiBandSet VDSL customized RFI configuration.
disable: not apply RFI notch to port
ansi: use pre-defined ANSI RFI notch
etsi: use pre-defined ETSI notch
custom: user needs to define customized RFI notch band through vdslRfiCustomTablerw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.4 |
vdslLineConfIpqosProfilerw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.5 |
vdslLineConfVturInpThis object is supported by R5.01 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.6 |
vdslLineConfVtucInpThis object is supported by R5.01 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.7 |
vdslLineConfOptionMaskThis object is supported by R5.01 and later versions.
Bit1: disable Trellis coding in ADSL mode
Bit2: disable Reed-Solomon coding for ADSL
Bit3: disable upstream bitswaps
Bit4: disable downstream bitwaps
Bit5: disable upstream 1-bit constellation support
Bit6: disable the transmit windowing in ADSL2+ mode
Bit7: disable S=0.5 support in G.dmt
Bit8: reserved
Bit9: enable nitro
Bit12: enable US PTM optimization
Bit13: enable DS PTM optimization
Bit14: enable US PHYR
Bit15: enable DS PHYRrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.8 |
vdslLineConfUpboForceLength-1 means auto electric length. This object is supported by R5.01 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.9 |
vdslLineConfPsdShapeThis object is supported by R5.01 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.10 |
vdslLineConfDpboThis object is supported by R5.01 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.11 |
vdslLineConfDpboParamEselThis object is supported by R5.01 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.12 |
vdslLineConfDpboParamEscma-1~-1.5 in step of 1/256. This object is supported by R5.01 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.13 |
vdslLineConfDpboParamEscmb-1~-1.5 in step of 1/256. This object is supported by R5.01 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.14 |
vdslLineConfDpboParamEscmc-1~-1.5 in step of 1/256. This object is supported by R5.01 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.15 |
vdslLineConfDpboParamMusThis object is supported by R5.01 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.16 |
vdslLineConfDpboParamFminThis object is supported by R5.01 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.17 |
vdslLineConfDpboParamFmaxThis object is supported by R5.01 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.18 |
vdslLineConfDpboParamPsdIdAlways return 0 when read. This object is supported by R5.01 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.19 |
vdslLineConfCompatibleCompatible to spectrum usage of adsl2 or adsl2+ line. The object is supported by R5.02 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.20 |
vdslLineConfPowerModeThe power mode of the VDSL line. This MIB object is supported by R5.05 and later versions.
1: fix
2: priorityToPower
3: priorityToRaterw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.21 |
vdslLineConfVturMaxTxPowerThe maximum allowed transmit power of VTU-R.
-130~200rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.22 |
vdslLineConfVtucMaxTxPowerThe maximum allowed transmit power of VTU-C.
-50~200rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.23 |
vdslLineConfMaxRxPowerThe maximum aggregate received power.
-255~255rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.24 |
vdslLineConfPMaskTo configure a bit mask to select preferred protocols :
0x00000001~0xffffffff
0x00000001 G.992.1 A|B
0x00000002 G.992.2 A
0x00000004 G.992.3 A|B
0x00000010 G.992.5 A|B
0x00000020 ANSI T1.413
0x00000040 ETSI TS 101 388
0x00000080 G.993.2 8a
0x00000100 G.993.2 8b
0x00000200 G.993.2 8c
0x00000400 G.993.2 8d
0x00000800 G.993.2 12a
0x00001000 G.993.2 12b
0x00002000 G.993.2 17a
0x00004000 G.992.3 M
0x00008000 G.992.3 J
0x00010000 G.992.3 L
0x00020000 G.992.3 L Narrow PSD
0x00040000 G.992.5 M
0x00080000 G.992.5 Jrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.25 |
vdslLineConfAturCarrierMaskSub-carrier masking for ADSL2+ fallback,
Upstream sub-carrier mask.rw OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.26 |
vdslLineConfAtucCarrierMask0Sub-carrier masking for ADSL2+ fallback,
Downstream sub-carrier mask.rw OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.27 |
vdslLineConfAtucCarrierMask1Sub-carrier masking for ADSL2+ fallback,
Downstream sub-carrier mask.rw OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.28 |
vdslLineConfSnrModeDsTo enable the transmitter referred virtual noise in the downstream direction.
1: enable(1)
2: disable(2)rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.29 |
vdslLineConfSnrModeUsTo enable the transmitter referred virtual noise in the upstream direction.
1: enable(1)
2: disable(2)rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.30 |
vdslLineConfTxRefVnDsTo configure downstream transmitter referred virtual noise.rw OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.31 |
vdslLineConfTxRefVnUsTo configure upstream transmitter referred virtual noise.rw OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.32 |
vdslLineConfTpstcTypeAdslTPS-TC type for ADSL mode VLC.
1: atm(1)
2: ptm(2)rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.33 |
vdslLineConfTpstcTypeVdslTPS-TC type for VDSL mode VLC.
1: atm(1)
2: ptm(2)rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.34 |
vdslLineConfVturInmEqThe INM Inmpulse Noise Protection Equivalent Mode.
Configuration parameter INM-INPEQ-MODE defines the way of computation of
Equivalent INP, as defined in ITU-T G.993.2 Amd2 11.4.2.2.1. This takes a
value in the range from 0 to 3.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.35 |
vdslLineConfVtucInmEqThe INM Inmpulse Noise Protection Equivalent Mode.
Configuration parameter INM-INPEQ-MODE defines the way of computation of
Equivalent INP, as defined in ITU-T G.993.2 Amd2 11.4.2.2.1. This takes a
value in the range from 0 to 3.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.36 |
vdslLineConfInmVturCCThe INM Cluster Continuation. The valid values for INMCC range from 0 from
64 DMT symbols in steps of 1 DMT symbol. Up to and including INMCC nondegraded
symbols will be allowed before a cluster is deemed to be complete and the impulse
noise event over.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.37 |
vdslLineConfInmVtucCCThe INM Cluster Continuation. The valid values for INMCC range from 0 from
64 DMT symbols in steps of 1 DMT symbol. Up to and including INMCC nondegraded
symbols will be allowed before a cluster is deemed to be complete and the impulse
noise event over.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.38 |
vdslLineConfInmVturIATOThe INM Inter Arrival Time Offset for the IAT anomaly generation. The valid values
for INMIATO range from 3 from 511 DMT symbols in steps of 1 DMT symbol.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.39 |
vdslLineConfInmVtucIATOThe INM Inter Arrival Time Offset for the IAT anomaly generation. The valid values
for INMIATO range from 3 from 511 DMT symbols in steps of 1 DMT symbol.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.40 |
vdslLineConfInmVturIATSThe INM Inter Arrival Time Step for the IAT anomaly generation. The valid values for
INMIATS range from 0 from 7 in steps. The range of values of inter-arrival times recorded
in a single bin is 2^(INMIATS). All inter-arrival times greater than or equal to INMIATO+6*(2^INMIATS)
are recorded in the 7th bin of INMAIAT.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.41 |
vdslLineConfInmVtucIATSThe INM Inter Arrival Time Step for the IAT anomaly generation. The valid values for
INMIATS range from 0 from 7 in steps. The range of values of inter-arrival times recorded
in a single bin is 2^(INMIATS). All inter-arrival times greater than or equal to INMIATO+6*(2^INMIATS)
are recorded in the 7th bin of INMAIAT.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.42 |
vdslLineConfInmVtucISDBUSISDD sensitivity of VTU-C,-128~127 in unit of 0.1dB.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.43 |
vdslLineConfGinpRtxModeDsG.inp(G.998.4) support setting on downstream direction. The possible values are:
Forbidden(0) - Support for G998.4 is disabled. Preferred(1) - If G998.4 is supported by the far-end, it is enabled.
Forced(2) - The line will only train if G998.4 can be enabled.
Test(3) - G998.4 is enabled in test mode (refer to G998.4, Clause 10.4).rw Xdsl2ConfigRtxMode .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.44 |
vdslLineConfGinpRtxModeUsG.inp(G.998.4) support setting on upstream direction. The possible values are:
Forbidden(0) - Support for G998.4 is disabled. Preferred(1) - If G998.4 is supported by the far-end, it is enabled.
Forced(2) - The line will only train if G998.4 can be enabled.
Test(3) - G998.4 is enabled in test mode (refer to G998.4, Clause 10.4).rw Xdsl2ConfigRtxMode .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.45 |
vdslLineConfGinpEtrMaxDsDefines the maximum allowed value for the ETR (Effective Throughput Rate).rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.46 |
vdslLineConfGinpEtrMaxUsDefines the maximum allowed value for the ETR (Effective Throughput Rate).rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.47 |
vdslLineConfGinpEtrMinDsDefines the minimum value for the ETR (Effective Throughput Rate).rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.48 |
vdslLineConfGinpEtrMinUsDefines the minimum value for the ETR (Effective Throughput Rate).rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.49 |
vdslLineConfGinpNdrMaxDsOverrules the wanted maximum data rate provided in the SetLineTrafficConfigurationrw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.50 |
vdslLineConfGinpNdrMaxUsOverrules the wanted maximum data rate provided in the SetLineTrafficConfigurationrw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.51 |
vdslLineConfGinpShineRatioDsThe assumed fraction (0.001 to 0.255) of NDR necessary to correct SHINE noise.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.52 |
vdslLineConfGinpShineRatioUsThe assumed fraction (0.001 to 0.255) of NDR necessary to correct SHINE noise.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.53 |
vdslLineConfGinpLeftrThresholdDsThe rate threshold (fraction of NDR) below which the Low Error Free Rate (LEFTR) defect is declared.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.54 |
vdslLineConfGinpLeftrThresholdUsThe rate threshold (fraction of NDR) below which the Low Error Free Rate (LEFTR) defect is declared.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.55 |
vdslLineConfGinpMaxDelayDsG.inp-specific value that overrules the traffic configuration setting.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.56 |
vdslLineConfGinpMaxDelayUsG.inp-specific value that overrules the traffic configuration setting.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.57 |
vdslLineConfGinpMinDelayDsG.inp-specific value that overrules the traffic configuration setting.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.58 |
vdslLineConfGinpMinDelayUsG.inp-specific value that overrules the traffic configuration setting.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.59 |
vdslLineConfGinpInpMinDsG.inp-specific value that overrules the traffic configuration setting. Unit is symbol.
The possible values are: 0-31rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.60 |
vdslLineConfGinpInpMinUsG.inp-specific value that overrules the traffic configuration setting. Unit is symbol.
The possible values are: 0-31rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.61 |
vdslLineConfGinpReinCfgInpDsG.inp-specific value that overrules the traffic configuration setting. Unit is symbol.
The possible values are: 0-7rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.62 |
vdslLineConfGinpReinCfgInpUsG.inp-specific value that overrules the traffic configuration setting. Unit is symbol.
The possible values are: 0-7rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.63 |
vdslLineConfGinpReinCfgFreqDsG.inp-specific value that overrules the traffic configuration setting. Unit is Hz.
The possible values are:
100 - 100Hz
120 - 120Hzrw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.64 |
vdslLineConfGinpReinCfgFreqUsG.inp-specific value that overrules the traffic configuration setting. Unit is Hz.
The possible values are:
100 - 100Hz
120 - 120Hzrw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.65 |
vdslLineConfSosMinRateB0DsThis parameter specifies the minimum net data rate required for a valid SOS request
in the downstream direction. The value shall be coded as an unsigned integer representing
the data rate as a multiple of 8 kbit/s.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.66 |
vdslLineConfSosMinRateB0UsThis parameter specifies the minimum net data rate required for a valid SOS request
in the upstream direction. The value shall be coded as an unsigned integer representing
the data rate as a multiple of 8 kbit/s.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.67 |
vdslLineConfSosTimeDsThe parameter SOS-TIME-ds is used in the specification of the receiver initiated SOS (see 13.4.3/G.993.2).
If the value of this parameter is not zero, the standard SOS triggering criteria are enabled, and the value
corresponds with duration of the time window used in the standard SOS triggering criteria in the downstream
direction. See G.993.2 for detailed usage rules. The special value zero indicates that the standard SOS triggering
criteria are disabled, i.e., vendor-discretionary values may be used instead of the values configured in the
MIB for the following parameters: SOS-NTONES-ds, SOS-CRC-ds, SOS-TIME-ds. This parameter applies in the downstream
direction. The valid range of non-zero values is from 64 ms to 16320 ms in steps of 64 ms.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.68 |
vdslLineConfSosTimeUsThe parameter SOS-TIME-ds is used in the specification of the receiver initiated SOS (see 13.4.3/G.993.2).
If the value of this parameter is not zero, the standard SOS triggering criteria are enabled, and the value
corresponds with duration of the time window used in the standard SOS triggering criteria in the upstream
direction. See G.993.2 for detailed usage rules. The special value zero indicates that the standard SOS triggering
criteria are disabled, i.e., vendor-discretionary values may be used instead of the values configured in the
MIB for the following parameters: SOS-NTONES-ds, SOS-CRC-ds, SOS-TIME-ds. This parameter applies in the upstream
direction. The valid range of non-zero values is from 64 ms to 16320 ms in steps of 64 ms.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.69 |
vdslLineConfSosCrcDsThis parameter is defined as the minimum number of normalized CRC anomalies received in SOS-TIME-ds seconds
in order to arm the second sub condition of the standard SOS triggering criteria (see 13.4.3.2/G.993.2) in
the downstream direction. See G.993.2 for detailed usage rules. The valid range of SOS-CRC values is 0.02 to
((2^16)-1)*0.02, in steps of 0.02.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.70 |
vdslLineConfSosCrcUsThis parameter is defined as the minimum number of normalized CRC anomalies received in SOS-TIME-ds seconds
in order to arm the second sub condition of the standard SOS triggering criteria (see 13.4.3.2/G.993.2) in
the upstream direction. See G.993.2 for detailed usage rules. The valid range of SOS-CRC values is 0.02 to
((2^16)-1)*0.02, in steps of 0.02.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.71 |
vdslLineConfSosNToneDsThis parameter is defined as the minimum percentage of tones in the downstream MEDLEY SET that must be
degraded in order to arm the first sub-condition of the standard SOS triggering criteria (see 13.4.3.2/G.993.2)
in the downstream direction. The parameter SOS-NTONES-ds is defined as a percentage of tones. See G.993.2 for
detailed usage rules. The valid range of values is from 1 to 100 in steps of 1. Use of the special value 0 is
described in 13.4.3.2/G.993.2.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.72 |
vdslLineConfSosNToneUsThis parameter is defined as the minimum percentage of tones in the upstream MEDLEY SET that must be
degraded in order to arm the first sub-condition of the standard SOS triggering criteria (see 13.4.3.2/G.993.2)
in the upstream direction. The parameter SOS-NTONES-ds is defined as a percentage of tones. See G.993.2 for
detailed usage rules. The valid range of values is from 1 to 100 in steps of 1. Use of the special value 0 is
described in 13.4.3.2/G.993.2.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.73 |
vdslLineConfSosMaxDsThis parameter is used in G.993.2 de-activation (see 12.1.4/G.993.2). If the number of successful SOS procedures
in the downstream direction performed within a 120-second interval exceeds MAX-SOS-ds, the modem shall transition
to the L3 state. See G.993.2 for detailed usage rules (see 12.1.4/G.993.2). The valid range of values is 1 to 15.
Use of the special value 0 is described in 12.1/G.993.2.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.74 |
vdslLineConfSosMaxUsThis parameter is used in G.993.2 de-activation (see 12.1.4/G.993.2). If the number of successful SOS procedures
in the upstream direction performed within a 120-second interval exceeds MAX-SOS-ds, the modem shall transition
to the L3 state. See G.993.2 for detailed usage rules (see 12.1.4/G.993.2). The valid range of values is 1 to 15.
Use of the special value 0 is described in 12.1/G.993.2.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.75 |
vdslLineConfSosMultiStepDsIndicates the capabilities of the VTU-R to execute the SOS request in one step or in multiple steps in the downstream direction.
The field is formatted as [gggg 0000]. The first four MSBs [gggg] indicate the maximum number of tones (GSOS) that can be executed
in a single step (GSOS)in the downstream direction. The valid values are:
- [0000]: No limitation
- [0010]: GSOS = 256 tones
- [0011]: GSOS = 512 tones
- [0100]: GSOS = 1024 tonesrw BITS .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.76 |
vdslLineConfSosMultiStepUsIndicates the capabilities of the VTU-R to execute the SOS request in one step or in multiple steps in the upstream direction.
The field is formatted as [gggg 0000]. The first four MSBs [gggg] indicate the maximum number of tones (GSOS) that can be executed
in a single step (GSOS)in the upstream direction. The valid values are:
- [0000]: No limitation
- [0010]: GSOS = 256 tones
- [0011]: GSOS = 512 tones
- [0100]: GSOS = 1024 tonesrw BITS .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.77 |
vdslLineConfRocEnableDsEnable the robust overhead channel.
disable(1),
enable(2)rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.78 |
vdslLineConfRocEnableUsEnable the robust overhead channel.
disable(1),
enable(2)rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.79 |
vdslLineConfRocSnrmDsThe parameter is defined as the SNR margin offset for the ROC channel in
the downstream direction. The parameter is used in the specification of the
channel initialization policy (see 12.3.7.1/G.993.2). The valid range of SNR
margin offset values is from 0 to 31 dB with 0.1 dB steps.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.80 |
vdslLineConfRocSnrmUsThe parameter is defined as the SNR margin offset for the ROC channel in
the upstream direction. The parameter is used in the specification of the
channel initialization policy (see 12.3.7.1/G.993.2). The valid range of SNR
margin offset values is from 0 to 31 dB with 0.1 dB steps.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.81 |
vdslLineConfRocMinInpDsThis parameter contains the minimum impulse noise protection to apply on the ROC
in the downstream direction. The minimum impulse noise protection is an integer ranging from 0 to 16.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.82 |
vdslLineConfRocMinInpUsThis parameter contains the minimum impulse noise protection to apply on the ROC
in the upstream direction. The minimum impulse noise protection is an integer ranging from 0 to 16.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.83 |
vdslLineConfSosEnableDsEnable the emergency rate reduction.
disable(1),
enable(2)rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.84 |
vdslLineConfSosEnableUsEnable the emergency rate reduction.
disable(1),
enable(2)rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.85 |
vdslLineConfDynamicDepthDsEnable the dynamic change of interleave depth.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.86 |
vdslLineConfDynamicDepthUsEnable the dynamic change of interleave depth.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.87 |
vdslLineConfDpboParamTyperw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.88 |
vdslLineConfDpboParamEselMinrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.89 |
vdslLineConfHsTxA43Psdrw INTEGER (-128..-32) UNITS "dB/HzB" .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.90 |
vdslLineConfHsTxB43Psdrw INTEGER (-128..-32) UNITS "dB/HzB" .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.91 |
vdslLineConfHsTxA43cB43cPsdrw INTEGER (-128..-32) UNITS "dB/HzB" .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.92 |
vdslLineConfHsTxV43Carrier257Psdrw INTEGER (-128..-32) UNITS "dB/HzB" .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.93 |
vdslLineConfHsTxV43Carrier383Psdrw INTEGER (-128..-32) UNITS "dB/HzB" .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.94 |
vdslLineConfHsTxV43Carrier511Psdrw INTEGER (-128..-32) UNITS "dB/HzB" .1.3.6.1.4.1.890.1.5.13.5.8.10.1.1.95 |
vdslVlan OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.10.2 |
vdslPortConfTableThis table includes common attributes describing the VDSL port.
This table is supported by R2.00 and later versions. SEQUENCE OF VdslPortConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.10.2.1 |
vdslPortConfEntryAn entry in vdslPortConfTable. VdslPortConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.10.2.1.1 |
vdslPortConfPvidThe PVID, the VLAN ID assigned to untagged frames or
Priority-Tagged frames received on this port.rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.8.10.2.1.1.1 |
vdslPortConfPriorityThe default ingress User Priority for this port.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.2.1.1.2 |
vdslPortConfAcceptableFrameTypeWhen this is admitOnlyVlanTagged(2) the device will
discard untagged frames or Priority-Tagged frames
received on this port. When admitAll(1), untagged
frames or Priority-Tagged frames received on this port
will be accepted and assigned to the PVID for this portrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.2.1.1.3 |
vdslPortConfTlsEnableEnable/disable the transparent LAN service.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.2.1.1.4 |
vdslPortConfTlsVidThe transparent LAN service s-tag VID.rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.8.10.2.1.1.5 |
vdslPortConfTlsPriorityThe transparent LAN service s-tag priority.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.2.1.1.6 |
vdslPortConfDtEnableEnable/disable double tag service on the specified subscriber port.
This MIB object is supported by R5.05 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.2.1.1.7 |
vdslPortConfDtSvidThe service provider VLAN ID. This MIB object is supported by R5.05 and later versions.rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.8.10.2.1.1.8 |
vdslPortConfDtSpriorityThe service VLAN priority. This MIB object is supported by R5.05 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.2.1.1.9 |
vdslPortConfDtCvidThe system-side customer VID. This MIB object is supported by R5.05 and later versions.rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.8.10.2.1.1.10 |
vdslPortConfDtCpriorityThe customer VLAN priority. This MIB object is supported by R5.05 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.2.1.1.11 |
vdslPortConfTlsPrioCopyEnableEnable/disable the priority copy of TLS.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.2.1.1.12 |
vdslPortVlanTableThis table includes common attributes describing the VDSL port.
This table is supported by R2.00 and later versions. SEQUENCE OF VdslPortVlanEntry .1.3.6.1.4.1.890.1.5.13.5.8.10.2.2 |
vdslPortVlanEntryAn entry in vdslPortVlanTable. VdslPortVlanEntry .1.3.6.1.4.1.890.1.5.13.5.8.10.2.2.1 |
vdslPortVlanRegThe port is egress or forbidden for this VLAN.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.2.2.1.1 |
vdslPortVlanTagThe port should transmit egress packets for this VLAN as tagged or untagged.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.2.2.1.2 |
vdslPortVlanRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.10.2.2.1.3 |
vdslVlanStaticTableA table containing static configuration information for
each VLAN configured into the device by (local or
network) management. All entries are permanent and will
be restored after the device is reset.
This table is supported by R2.00 and later versions. SEQUENCE OF VdslVlanStaticEntry .1.3.6.1.4.1.890.1.5.13.5.8.10.2.3 |
vdslVlanStaticEntryAn entry in vdslVlanStaticTable. VdslVlanStaticEntry .1.3.6.1.4.1.890.1.5.13.5.8.10.2.3.1 |
vdslVlanStaticEgressPortsThe set of ports which are permanently assigned to the
egress list for this VLAN by management.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.8.10.2.3.1.1 |
vdslVlanStaticUntaggedPortsThe set of ports which should transmit egress packets for this VLAN as untagged.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.8.10.2.3.1.2 |
vdslVlanStaticRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.10.2.3.1.3 |
vdslPortPvlanTableThis table is supported by R5.01 and later versions. SEQUENCE OF VdslPortPvlanEntry .1.3.6.1.4.1.890.1.5.13.5.8.10.2.4 |
vdslPortPvlanEntryAn entry in vdslPortPvlanTable. VdslPortPvlanEntry .1.3.6.1.4.1.890.1.5.13.5.8.10.2.4.1 |
vdslPortPvlanEtype0~0xffff.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.10.2.4.1.1 |
vdslPortPvlanVidro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.8.10.2.4.1.2 |
vdslPortPvlanPriorityrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.2.4.1.3 |
vdslPortPvlanRowStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.10.2.4.1.4 |
vdslRfiCustomTableThis table includes VDSL customized RFI configuration.
This table is supported by R2.00 and later versions. SEQUENCE OF VdslRfiCustomEntry .1.3.6.1.4.1.890.1.5.13.5.8.10.3 |
vdslRfiCustomEntryAn entry in vdslRfiCustomTable. VdslRfiCustomEntry .1.3.6.1.4.1.890.1.5.13.5.8.10.3.1 |
vdslRfiCustomIndexIndex of the table.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.3.1.1 |
vdslRfiCustomStartFreqThe start value of the customized frequency range.rw INTEGER UNITS "KHz" .1.3.6.1.4.1.890.1.5.13.5.8.10.3.1.2 |
vdslRfiCustomEndFreqThe end value of the customized frequency range.rw INTEGER UNITS "KHz" .1.3.6.1.4.1.890.1.5.13.5.8.10.3.1.3 |
vdslRfiCustomEnableEnable or disable the customized frequency range setting.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.3.1.4 |
vdslRfiCustomModeNotch : sent at -80 dBm in the specified frequency bands.
Gap : cut the power completely in the specified frequency bands.
1: notch(1)
2: gap(2)rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.10.3.1.5 |
vdslLineConfUpboParamTableThis table includes VDSL UPBO configuration.
This table is supported by R5.01 and later versions. SEQUENCE OF VdslLineConfUpboParamEntry .1.3.6.1.4.1.890.1.5.13.5.8.10.4 |
vdslLineConfUpboParamEntryAn entry in vdslLineConfUpboParamTable. VdslLineConfUpboParamEntry .1.3.6.1.4.1.890.1.5.13.5.8.10.4.1 |
vdslLineConfUpboParamBandIndex of the table.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.4.1.1 |
vdslLineConfUpboParamArw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.4.1.2 |
vdslLineConfUpboParamBrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.4.1.3 |
vdslLineConfDpboTableThis table includes VDSL DPBO configuration.
This table is supported by R5.01 and later versions. SEQUENCE OF VdslLineConfDpboEntry .1.3.6.1.4.1.890.1.5.13.5.8.10.5 |
vdslLineConfDpboEntryAn entry in vdslLineConfDpboTable. VdslLineConfDpboEntry .1.3.6.1.4.1.890.1.5.13.5.8.10.5.1 |
vdslLineConfDpboIndexIndex of the table.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.5.1.1 |
vdslLineConfDpboTonerw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.5.1.2 |
vdslLineConfDpboPsdrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.10.5.1.3 |
ipbpvc OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.11 |
ipbpvcDomainTableThis table includes ipbpvc domain configuration.
This table is supported by R3.00 and later versions. SEQUENCE OF IpbpvcDomainEntry .1.3.6.1.4.1.890.1.5.13.5.8.11.1 |
ipbpvcDomainEntryAn entry of ipbpvcDomainTable. IpbpvcDomainEntry .1.3.6.1.4.1.890.1.5.13.5.8.11.1.1 |
ipbpvcDomainNameName of the domain.ro DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.11.1.1.1 |
ipbpvcDomainRowStatusRow status of the table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.11.1.1.2 |
ipbpvcDomainVlanTableThis table includes ipbpvc domain VLAN configuration.
This table is supported by R3.00 and later versions. SEQUENCE OF IpbpvcDomainVlanEntry .1.3.6.1.4.1.890.1.5.13.5.8.11.2 |
ipbpvcDomainVlanEntryAn entry of ipbpvcDomainVlanTable. IpbpvcDomainVlanEntry .1.3.6.1.4.1.890.1.5.13.5.8.11.2.1 |
ipbpvcDomainVlanIdSet VLAN to join or leave the specified domain.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.8.11.2.1.1 |
ipbpvcDomainDhcpVlanEnableEnable/disable DHCP VLAN in a domain.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.11.2.1.2 |
ipbpvcDomainVlanRowStatusRow status of the table used to create/delete an entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.11.2.1.3 |
ipbpvcEdgeRouterTableThis table includes ipbpvc edge router configuration.
This table is supported by R3.00 and later versions. SEQUENCE OF IpbpvcEdgeRouterEntry .1.3.6.1.4.1.890.1.5.13.5.8.11.3 |
ipbpvcEdgeRouterEntryAn entry of ipbpvcEdgeRouterTable. IpbpvcEdgeRouterEntry .1.3.6.1.4.1.890.1.5.13.5.8.11.3.1 |
ipbpvcEdgeRouterIpIP address of the edge router.ro IpAddress .1.3.6.1.4.1.890.1.5.13.5.8.11.3.1.1 |
ipbpvcEdgeRouterVidVLAN ID of the edge router.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.8.11.3.1.2 |
ipbpvcEdgeRouterMaskNetmask of the edge router.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.11.3.1.3 |
ipbpvcEdgeRouterRowStatusRow status of the table used to create/delete an entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.11.3.1.4 |
ipbpvcInterfaceTableThis table includes ipbpvc interface configuration.
This table is supported by R3.00 and later versions. SEQUENCE OF IpbpvcInterfaceEntry .1.3.6.1.4.1.890.1.5.13.5.8.11.4 |
ipbpvcInterfaceEntryAn entry of ipbpvcInterfaceTable. IpbpvcInterfaceEntry .1.3.6.1.4.1.890.1.5.13.5.8.11.4.1 |
ipbpvcInterfaceIpIP address of the interface.ro IpAddress .1.3.6.1.4.1.890.1.5.13.5.8.11.4.1.1 |
ipbpvcInterfaceMaskNetmask of the interface.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.11.4.1.2 |
ipbpvcInterfaceVidVLAN ID of the interface.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.8.11.4.1.3 |
ipbpvcInterfaceIfIndexIfIndex of the interface.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.11.4.1.4 |
ipbpvcInterfaceVpiVPI of the interface.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.11.4.1.5 |
ipbpvcInterfaceVciVCI of the interface.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.11.4.1.6 |
ipbpvcInterfaceRowStatusRow status of the table used to create/delete an entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.11.4.1.7 |
ipbpvcRouteTableThis table includes ipbpvc route configuration.
This table is supported by R3.00 and later versions. SEQUENCE OF IpbpvcRouteEntry .1.3.6.1.4.1.890.1.5.13.5.8.11.5 |
ipbpvcRouteEntryAn entry of ipbpvcRouteTable. IpbpvcRouteEntry .1.3.6.1.4.1.890.1.5.13.5.8.11.5.1 |
ipbpvcRouteIpIP address of the route.ro IpAddress .1.3.6.1.4.1.890.1.5.13.5.8.11.5.1.1 |
ipbpvcRouteMaskNetmask of the route.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.11.5.1.2 |
ipbpvcRouteNextHopNext hop IP address of the route.ro IpAddress .1.3.6.1.4.1.890.1.5.13.5.8.11.5.1.3 |
ipbpvcRouteMetricMetric of the route.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.11.5.1.4 |
ipbpvcRoutePriorityPriority of the route. Note that the default value of this object is 8, which means
we keep the original priority of the packet(frame).rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.11.5.1.5 |
ipbpvcRouteRowStatusRow status of the table used to create/delete an entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.11.5.1.6 |
ipbpvcTableThis table includes ipbpvc configuration.
This table is supported by R3.00 and later versions. SEQUENCE OF IpbpvcEntry .1.3.6.1.4.1.890.1.5.13.5.8.11.6 |
ipbpvcEntryAn entry of ipbpvcTable. IpbpvcEntry .1.3.6.1.4.1.890.1.5.13.5.8.11.6.1 |
ipbpvcVpiVPI of the PVC.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.11.6.1.1 |
ipbpvcVciVCI of the PVC.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.11.6.1.2 |
ipbpvcPvidPVID of the PVC.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.11.6.1.3 |
ipbpvcEncapType of the PVC.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.11.6.1.4 |
ipbpvcPriorityPriority of the PVC.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.11.6.1.5 |
ipbpvcProfileProfile of the PVC.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.11.6.1.6 |
ipbpvcRowStatusRow status of the table used to create/delete an entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.11.6.1.7 |
ipbpvcVlanTableThis table includes ipbpvc VLAN configuration.
This table is supported by R3.00 and later versions. SEQUENCE OF IpbpvcVlanEntry .1.3.6.1.4.1.890.1.5.13.5.8.11.7 |
ipbpvcVlanEntryAn entry of ipbpvcVlanTable. IpbpvcVlanEntry .1.3.6.1.4.1.890.1.5.13.5.8.11.7.1 |
ipbpvcVlanRegThe PVC is egress or forbidden for this VLAN.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.11.7.1.1 |
ipbpvcVlanTagThe PVC should transmit egress packets for this VLAN as tagged or untagged.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.11.7.1.2 |
ipbpvcVlanRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.11.7.1.3 |
arpproxy OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.11.8 |
arpproxyAgeAging time of the ARP proxy.
This object is supported by R3.00 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.11.8.1 |
arpproxyFlush OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.11.8.2 |
arpproxyFlushTargetThe target whose ARP table to be flushed.
This object is supported by R3.00 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.11.8.2.1 |
arpproxyFlushOpsSet the object to 1 to start flushing.
This object is supported by R3.00 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.11.8.2.2 |
arpproxyFlushEdgeRouterIpFlush ARP table for the specified edge router.
This object is supported by R3.00 and later versions.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.8.11.8.2.3 |
arpproxyFlushEdgeRouterVidFlush ARP table for the specified edge router.
This object is supported by R3.00 and later versions.rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.8.11.8.2.4 |
arpproxyFlushInterfaceIpFlush ARP table for the specified interface.
This object is supported by R3.00 and later versions.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.8.11.8.2.5 |
arpproxyFlushInterfaceMaskFlush ARP table for the specified interface.
This object is supported by R3.00 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.11.8.2.6 |
arpproxyFlushInterfaceVidFlush ARP table for the specified interface.
This object is supported by R3.00 and later versions.rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.8.11.8.2.7 |
voipPort OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.12 |
voipSipLineConfTableThis table includes common attributes describing the VoIP line. SEQUENCE OF VoipSipLineConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.12.1 |
voipSipLineConfEntryAn entry in voipSipLineConfTable. VoipSipLineConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.12.1.1 |
voipSipLineConfSipProfileSIP profile name.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.12.1.1.1 |
voipSipLineConfSipCallSvcProfileSIP call service profile name.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.12.1.1.2 |
voipSipLineConfDspProfileDSP profile name.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.12.1.1.3 |
voipSipLineConfAccountAccount for SIP registration.
This object is supported by R5.05 and later versions.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.12.1.1.4 |
voipSipLineConfPasswordPassword for SIP registration.
This object is supported by R5.05 and later versions.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.12.1.1.5 |
voipSipLineConfDataProfileDSP profile name of data mode, up to 31 characters.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.12.1.1.6 |
voipPortH248 OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.12.2 |
voipH248LineConfTableThis table includes common attributes describing the VoIP line.
This table is supported by R5.01 and later versions. SEQUENCE OF VoipH248LineConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.12.2.1 |
voipH248LineConfEntryAn entry in voipH248LineConfTable. VoipH248LineConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.12.2.1.1 |
voipH248LineConfMgNameMG name.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.12.2.1.1.1 |
voipH248LineConfDspProfileDSP profile.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.12.2.1.1.2 |
voipH248LineConfDataProfileDSP profile name of data mode, up to 31 characters.
This MIB object is supported by R5.06 and later versions.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.12.2.1.1.3 |
voipH248TerminationTableThis table is supported by R5.01 and later versions. SEQUENCE OF VoipH248TerminationEntry .1.3.6.1.4.1.890.1.5.13.5.8.12.2.2 |
voipH248TerminationEntryAn entry in voipH248TerminationTable. VoipH248TerminationEntry .1.3.6.1.4.1.890.1.5.13.5.8.12.2.2.1 |
voipH248TerminationNameTermination name.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.12.2.2.1.1 |
voipPotsImpedanceConfTableThis table is supported by R5.01 and later versions. SEQUENCE OF VoipPotsImpedanceConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.12.3 |
voipPotsImpedanceConfEntryAn entry in voipPotsImpedanceConfTable. VoipPotsImpedanceConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.12.3.1 |
voipPotsImpedanceDefault impedance is from impedance of country code.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.12.3.1.1 |
voipPotsGainConfTableThis table is supported by R5.01 and later versions. SEQUENCE OF VoipPotsGainConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.12.4 |
voipPotsGainConfEntryAn entry in voipPotsGainConfTable. VoipPotsGainConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.12.4.1 |
voipPotsTxGainrw INTEGER (-200..200) UNITS "0.1dB" .1.3.6.1.4.1.890.1.5.13.5.8.12.4.1.1 |
voipPotsRxGainrw INTEGER (-200..200) UNITS "0.1dB" .1.3.6.1.4.1.890.1.5.13.5.8.12.4.1.2 |
voipPotsDataTxGainThis MIB object is supported by R5.06 and later versions.rw INTEGER (-200..200) UNITS "0.1dB" .1.3.6.1.4.1.890.1.5.13.5.8.12.4.1.3 |
voipPotsDataRxGainThis MIB object is supported by R5.06 and later versions.rw INTEGER (-200..200) UNITS "0.1dB" .1.3.6.1.4.1.890.1.5.13.5.8.12.4.1.4 |
voipOpmodeConfTableThis table is supported by R5.01 and later versions. SEQUENCE OF VoipOpmodeConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.12.5 |
voipOpmodeConfEntryAn entry in voipOpmodeConfTable. VoipOpmodeConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.12.5.1 |
voipOpModeConfigure operation mode to specified subscribers. Default is normal SIP server
and v5sip is V5.2 access gateway.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.12.5.1.1 |
voipPolarityReverseConfTableThis table is supported by R5.05 and later versions. SEQUENCE OF VoipPolarityReverseConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.12.6 |
voipPolarityReverseConfEntryAn entry in voipPolarityReverseConfTable. VoipPolarityReverseConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.12.6.1 |
voipPolarityReverseEnable/disable polarity reverse function. Polarity reverse is feature to reversed tip and ring after call establish and terminate.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.12.6.1.1 |
voipPotsCidConfTable SEQUENCE OF VoipPotsCidConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.12.7 |
voipPotsCidConfEntryAn entry in voipPotsCidConfTable. VoipPotsCidConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.12.7.1 |
voipPotsCidASType0: DEFVAL (use the setting of country code)
1: CID during ring
2: DTAS CID before ring
3: RPAS CID before ring
4: LR DTAS CID before ring
5: LR CID before ring
6: CID before ringrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.12.7.1.1 |
voipPotsCidPayloadType0: DEFVAL (use the setting of country code)
1: MDMF
2: SDMF
3: ETSI MDMF
4: ETSI SDMF
5: DTMF
6: UK MDMF
7: UK SDMF
8: Japanese MDMFrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.12.7.1.2 |
voipPotsLineConfTableper-interface table for pots configuration SEQUENCE OF VoipPotsLineConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.12.8 |
voipPotsLineConfEntryAn entry in voipPotsLineConfTable. VoipPotsLineConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.12.8.1 |
voipPotsLineFlashDefaultset positive non-zero value to configure default flash timer settingsrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.12.8.1.1 |
voipPotsLineFlashMaxminimum flash period in msrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.12.8.1.2 |
voipPotsLineFlashMinmaximum flash period in msrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.12.8.1.3 |
voipPotsLineLoopmaximum loop resistance valuerw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.12.8.1.4 |
enetPort OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.13 |
enetLineConfTableThe table contains ethernet line configuration. SEQUENCE OF EnetLineConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.13.1 |
enetLineConfEntry EnetLineConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.13.1.1 |
enetLineConfBandWidthIngress0~99968Kbps in step of 64Kbps, 0 means no limit.rw INTEGER UNITS "Kbps" .1.3.6.1.4.1.890.1.5.13.5.8.13.1.1.1 |
enetLineConfBandWidthEgress0~99968Kbps in step of 64Kbps, 0 means no limit.rw INTEGER UNITS "Kbps" .1.3.6.1.4.1.890.1.5.13.5.8.13.1.1.2 |
enetLineConfFlowCtrlEnableEnable/disable flow control.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.13.1.1.3 |
enetLineConfSpeedPort spd/dplx configuration.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.13.1.1.4 |
enetPortConfTableThe table contains ethernet line configuration. SEQUENCE OF EnetPortConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.13.2 |
enetPortConfEntry EnetPortConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.13.2.1 |
enetPortConfPriorityThe default ingress User Priority for this port.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.13.2.1.1 |
enetPortConfPvidThe PVID, the VLAN ID assigned to untagged frames or Priority-Tagged frames received on this port.rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.8.13.2.1.2 |
enetPortConfAcceptableFrameTypeWhen this is admitOnlyVlanTagged(2) the device will discard untagged frames or
Priority-Tagged frames received on this port. When admitAll(1), untagged frames or
Priority-Tagged frames received on this port will be accepted and assigned to
the PVID for this port.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.13.2.1.3 |
enetPortConfTlsEnablerw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.13.2.1.4 |
enetPortConfTlsVidThe transparent LAN VID.rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.8.13.2.1.5 |
enetPortConfTlsPriorityThe transparent LAN priority.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.13.2.1.6 |
enetPortConfRateLimitProfileRate Limit Profile name. This object is supported by R5.02 and later versions.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.13.2.1.7 |
enetPortConfQueueRateLimitProfileSet queue rate limit profile.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.13.2.1.8 |
enetPortConfDtEnableEnable/disable double tag service on the specified subscriber port.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.13.2.1.9 |
enetPortConfDtSvidThe service provider VLAN ID.rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.8.13.2.1.10 |
enetPortConfDtSpriorityThe service VLAN priority.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.13.2.1.11 |
enetPortConfDtCvidThe system-side customer VID.rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.8.13.2.1.12 |
enetPortVlanTableThe table contains ethernet line vlan configuration. SEQUENCE OF EnetPortVlanEntry .1.3.6.1.4.1.890.1.5.13.5.8.13.3 |
enetPortVlanEntry EnetPortVlanEntry .1.3.6.1.4.1.890.1.5.13.5.8.13.3.1 |
enetPortVlanRegrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.13.3.1.1 |
enetPortVlanTagrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.13.3.1.2 |
enetPortVlanRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.13.3.1.3 |
elcDot3ad OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.13.4 |
elcDot3adTableThe table contains dot3ad configuration. This table is supported by R5.01 and later versions. SEQUENCE OF ElcDot3adEntry .1.3.6.1.4.1.890.1.5.13.5.8.13.4.1 |
elcDot3adEntry ElcDot3adEntry .1.3.6.1.4.1.890.1.5.13.5.8.13.4.1.1 |
elcDot3adSlotIdro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.13.4.1.1.1 |
elcDot3adGroupIdro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.13.4.1.1.2 |
elcDot3adEnablerw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.13.4.1.1.3 |
elcAggPortTableThe table contains port aggregation configuration. This table is supported by R5.01 and later versions. SEQUENCE OF ElcAggPortEntry .1.3.6.1.4.1.890.1.5.13.5.8.13.4.2 |
elcAggPortEntry ElcAggPortEntry .1.3.6.1.4.1.890.1.5.13.5.8.13.4.2.1 |
elcAggPortJoinrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.13.4.2.1.1 |
enetQoS OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.13.5 |
enetQScheduleTable SEQUENCE OF EnetQScheduleEntry .1.3.6.1.4.1.890.1.5.13.5.8.13.5.1 |
enetQScheduleEntry EnetQScheduleEntry .1.3.6.1.4.1.890.1.5.13.5.8.13.5.1.1 |
enetQScheduleTypeQueue scheduling type (strictly priority queue or weighted round robin).rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.13.5.1.1.1 |
enetQueueWeightTable SEQUENCE OF EnetQueueWeightEntry .1.3.6.1.4.1.890.1.5.13.5.8.13.5.2 |
enetQueueWeightEntry EnetQueueWeightEntry .1.3.6.1.4.1.890.1.5.13.5.8.13.5.2.1 |
enetQueueWeightWeight for the priority queue, 0 means strict priorityrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.13.5.2.1.1 |
enetPortPvlanTable SEQUENCE OF EnetPortPvlanEntry .1.3.6.1.4.1.890.1.5.13.5.8.13.6 |
enetPortPvlanEntryAn entry in enetPortPvlanTable. EnetPortPvlanEntry .1.3.6.1.4.1.890.1.5.13.5.8.13.6.1 |
enetPortPvlanEtypero Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.13.6.1.1 |
enetPortPvlanVidro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.8.13.6.1.2 |
enetPortPvlanPriorityrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.13.6.1.3 |
enetPortPvlanRowStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.13.6.1.4 |
enetPortXvlanTable SEQUENCE OF EnetPortXvlanEntry .1.3.6.1.4.1.890.1.5.13.5.8.13.7 |
enetPortXvlanEntry EnetPortXvlanEntry .1.3.6.1.4.1.890.1.5.13.5.8.13.7.1 |
enetPortXvlanCvidthe original vlan id in the 8021q tag, 1~4094ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.13.7.1.1 |
enetPortXvlanSvidthe result vlan id in the 8021q tag, or in the QinQ S-tag, 1~4094ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.13.7.1.2 |
enetPortXvlanRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.13.7.1.3 |
gbondGroupTableThe table contains bonding group configuration. This table is supported by R5.01 and later versions. SEQUENCE OF GbondGroupEntry .1.3.6.1.4.1.890.1.5.13.5.8.14 |
gbondGroupEntry GbondGroupEntry .1.3.6.1.4.1.890.1.5.13.5.8.14.1 |
gbondGroupNameAn administratively assigned string, which may be used to identify bonding group.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.14.1.1 |
gbondGroupPortsThe set of ports which are currently assigned to
the bonding group of specified group name. Each bit in the octet specifies
a port from MSB to LSB. For example: 32(hex) = 50(dec) = 00110010(bin) means
the port 3, 4 and 7.rw OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.8.14.1.2 |
gbondGroupRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.14.1.3 |
dtpvc OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.15 |
dtpvcTableThis table includes Double Tagging PVC configuration.
This table is supported by R5.02 and later versions. SEQUENCE OF DtpvcEntry .1.3.6.1.4.1.890.1.5.13.5.8.15.1 |
dtpvcEntryAn entry of dtpvcTable. DtpvcEntry .1.3.6.1.4.1.890.1.5.13.5.8.15.1.1 |
dtpvcVpiVPI of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.15.1.1.1 |
dtpvcVciVCI of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.15.1.1.2 |
dtpvcSvids-tag of the pvc.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.8.15.1.1.3 |
dtpvcCvidc-tag of the pvc.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.8.15.1.1.4 |
dtpvcEncapEncapsulation of the pvc.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.15.1.1.5 |
dtpvcSPrioritys-priority of the pvc.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.15.1.1.6 |
dtpvcCPriorityc-priority of the pvc.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.15.1.1.7 |
dtpvcProfileThe value of this object identifies the row in the atmProfileTable, which applies for this pvc.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.15.1.1.8 |
dtpvcRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.15.1.1.9 |
dtpvcMvlanEnableEnable/disable multicast VLAN function for the DTPVC.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.15.1.1.10 |
e1Port OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.16 |
e1PortConfTableThis table is supported by R5.03 and later versions.
The table contains E1 line configuration. SEQUENCE OF E1PortConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.16.1 |
e1PortConfEntry E1PortConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.16.1.1 |
e1PortConfAdminStatusrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.16.1.1.1 |
e1PortConfAlarmProfilerw DisplayString .1.3.6.1.4.1.890.1.5.13.5.8.16.1.1.2 |
e1PortConfImpedancerw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.16.1.1.3 |
e1PortConfTimingSrc0: local, 1~8 E1 port: the timing source port idrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.16.1.1.4 |
xvlan OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.17 |
xvlanTableThis table is supported by R5.04 and later versions. SEQUENCE OF XvlanEntry .1.3.6.1.4.1.890.1.5.13.5.8.17.1 |
xvlanEntry XvlanEntry .1.3.6.1.4.1.890.1.5.13.5.8.17.1.1 |
xvlanCvidthe original vlan id in the 8021q tag, 1~4094ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.17.1.1.1 |
xvlanSvidthe result vlan id in the 8021q tag, or in the QinQ S-tag, 1~4094ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.17.1.1.2 |
xvlanCvidsthe result vlan id in the QinQ C-tag, 0~4094, 0 means single tagro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.8.17.1.1.3 |
xvlanRowStatusThis object is used to create a new row or delete an existing row in this table.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.17.1.1.4 |
vdsl2Port OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.18 |
vdsl2LineConfTableThis table is supported by R5.06 and later versions. SEQUENCE OF Vdsl2LineConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.18.1 |
vdsl2LineConfEntry Vdsl2LineConfEntry .1.3.6.1.4.1.890.1.5.13.5.8.18.1.1 |
vdsl2LineConfRateLimitProfileSet rate limit profilerw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.18.1.1.1 |
vdsl2LineConfQueueRateLimitProfileSet queue rate limit profilerw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.18.1.1.2 |
vdsl2Pvc OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.18.2 |
vdsl2PvcTableThis table is supported by R5.06 and later versions. SEQUENCE OF Vdsl2PvcEntry .1.3.6.1.4.1.890.1.5.13.5.8.18.2.1 |
vdsl2PvcEntry Vdsl2PvcEntry .1.3.6.1.4.1.890.1.5.13.5.8.18.2.1.1 |
vdsl2PvcVpiVPI of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.18.2.1.1.1 |
vdsl2PvcVciVCI of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.18.2.1.1.2 |
vdsl2PvcPvidDefault VID of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.18.2.1.1.3 |
vdsl2PvcEncapEncapsulation of the pvc.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.18.2.1.1.4 |
vdsl2PvcPriority802.1p default priority of the pvc.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.18.2.1.1.5 |
vdsl2PvcSuperrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.18.2.1.1.6 |
vdsl2PvcRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.18.2.1.1.7 |
vdsl2QSchedule OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.18.3 |
vdsl2QScheduleTableThe table contains queue schedule configuration for the vdsl2 ports. SEQUENCE OF Vdsl2QSchedulePortEntry .1.3.6.1.4.1.890.1.5.13.5.8.18.3.1 |
vdsl2QScheduleEntry Vdsl2QSchedulePortEntry .1.3.6.1.4.1.890.1.5.13.5.8.18.3.1.1 |
vdsl2QScheduleTypeQueue scheduling type (strictly priority queue or weighted round robin).rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.18.3.1.1.1 |
vdsl2QueueWeightTableThe table contains weight configuration for the priority queues. SEQUENCE OF Vdsl2QueueWeightEntry .1.3.6.1.4.1.890.1.5.13.5.8.18.3.2 |
vdsl2QueueWeightEntry Vdsl2QueueWeightEntry .1.3.6.1.4.1.890.1.5.13.5.8.18.3.2.1 |
vdsl2QueueWeightWeight for the priority queue, 0 means strict priorityrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.18.3.2.1.1 |
vdsl2Paepvc OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.18.4 |
vdsl2PaepvcTableThis table includes PPPoAoE PVC configuration.
This table is supported by R1.02 and later versions. SEQUENCE OF Vdsl2PaepvcEntry .1.3.6.1.4.1.890.1.5.13.5.8.18.4.1 |
vdsl2PaepvcEntryAn entry of vdsl2PaepvcTable. Vdsl2PaepvcEntry .1.3.6.1.4.1.890.1.5.13.5.8.18.4.1.1 |
vdsl2PaepvcVpiVPI of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.18.4.1.1.1 |
vdsl2PaepvcVciVCI of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.18.4.1.1.2 |
vdsl2PaepvcPvidDefault VID of the pvc.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.8.18.4.1.1.3 |
vdsl2PaepvcEncapEncapsulation of the pvc.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.18.4.1.1.4 |
vdsl2PaepvcPriority802.1p default priority of the pvc.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.18.4.1.1.5 |
vdsl2PaepvcAcNameAccess concentrator name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.18.4.1.1.6 |
vdsl2PaepvcServiceNameService name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.18.4.1.1.7 |
vdsl2PaepvcHelloTimeThe system will close the PVC if there are not any LCP echo messages passed through
during the LCP hello time.rw INTEGER UNITS "second" .1.3.6.1.4.1.890.1.5.13.5.8.18.4.1.1.8 |
vdsl2PaepvcRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.8.18.4.1.1.9 |
pvcAll OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.8.19 |
pvcAllFilterIfindex to filter pvc, value 0 indicates to display all.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.19.1 |
pvcAllTable SEQUENCE OF PvcAllEntry .1.3.6.1.4.1.890.1.5.13.5.8.19.2 |
pvcAllEntry PvcAllEntry .1.3.6.1.4.1.890.1.5.13.5.8.19.2.1 |
pvcAllVpiVPI of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.19.2.1.1 |
pvcAllVciVCI of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.8.19.2.1.2 |
pvcAllEncapEncapsulation of the pvc.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.19.2.1.3 |
pvcAllTypeType of the pvc.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.8.19.2.1.4 |
profile OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.9 |
adslProfile OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.9.1 |
maxNumOfAdslLineProfilesThe maximum number of ADSL line profiles supported by the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.1.1 |
maxNumOfAdslAlarmProfilesThe maximum number of ADSL alarm profiles supported by the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.1.2 |
shdslProfile OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.9.2 |
maxNumOfShdslLineProfilesThe maximum number of SHDSL line profiles supported by the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.2.1 |
maxNumOfShdslAlarmProfilesThe maximum number of SHDSL alarm profiles supported by the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.2.2 |
atmProfile OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.9.3 |
maxNumOfAtmProfilesThe maximum number of ATM profiles supported by the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.3.1 |
atmProfileTableThis table contains information on the PVC configuration. One entry in this table
reflects a profile which can be used to configure the PVC. SEQUENCE OF AtmProfileEntry .1.3.6.1.4.1.890.1.5.13.5.9.3.2 |
atmProfileEntryAn entry in atmProfileTable. AtmProfileEntry .1.3.6.1.4.1.890.1.5.13.5.9.3.2.1 |
atmProfileNameThis object is used by the ATM profile table in order to identify a row of this table.ro DisplayString .1.3.6.1.4.1.890.1.5.13.5.9.3.2.1.1 |
atmProfileAALATM Adaptation Layer policy.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.3.2.1.2 |
atmProfileClassATM traffic class, including constant bit rate,
real-time variable bit rate, non real-time variable bit rate,
unspecified bit rate, and available bit rate.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.3.2.1.3 |
atmProfilePcrPeak Cell Rate.rw Unsigned32 UNITS "cells per second" .1.3.6.1.4.1.890.1.5.13.5.9.3.2.1.4 |
atmProfileCdvtCell Delay Variation Tolerance.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.3.2.1.5 |
atmProfileScrMcrSustain Cell Rate for vbr or Minimum Cell Rate for abr.rw Unsigned32 UNITS "cells per second" .1.3.6.1.4.1.890.1.5.13.5.9.3.2.1.6 |
atmProfileBtBurst Tolerance for vbr.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.3.2.1.7 |
atmProfileRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.3.2.1.8 |
profsvr OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.9.4 |
profileServerModeThe object indicates the system is running profile server with server mode or client mode.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.4.1 |
profileServerIpIP address of the profile server.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.9.4.2 |
profsvrClientTableThis table includes the clients to be provisioned. SEQUENCE OF ProfsvrClientEntry .1.3.6.1.4.1.890.1.5.13.5.9.4.3 |
profsvrClientEntryAn entry of profsvrClientTable. ProfsvrClientEntry .1.3.6.1.4.1.890.1.5.13.5.9.4.3.1 |
profsvrClientIpIP address of the client to be provisioned.ro IpAddress .1.3.6.1.4.1.890.1.5.13.5.9.4.3.1.1 |
profsvrClientTypeProvision type to decide whether deleting unmapped profiles in client or not.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.4.3.1.2 |
profsvrClientRowStatusThe row status is used to create or delete a client.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.4.3.1.3 |
profileServerSyncThe manager sets the object to be one to start profile synchronization.
The agent should clear the object to be zero when the operation is completed.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.4.4 |
aclProfile OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.9.5 |
aclProfileTableThis table is supported by R1.03 and later versions. SEQUENCE OF AclProfileEntry .1.3.6.1.4.1.890.1.5.13.5.9.5.1 |
aclProfileEntryAn entry of aclProfileTable. AclProfileEntry .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1 |
aclProfileRuleNameProfile rule namero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.1 |
aclProfileRuleNumberThe managed object is for acl profile rule configuration.
etype <etype> vlan <vid> (1),
etype <etype> smac <mac> (2),
etype <etype> dmac <mac> (3),
vlan <vid> smac <mac> (4),
vlan <vid> dmac <mac> (5),
smac <mac> dmac <mac> (6),
vlan <vid> priority <priority> (7),
etype <etype> (8),
vlan <vid> (9),
smac <mac> (10),
dmac <mac> (11),
priority <priority> (12),
protocol <protocol> (13),
{srcip <ip>/<mask>{|dstip <ip>/<mask>{|tos <stos> <etos>{|srcport <sport> <eport> {|dstport <sport> <eport>}}}}} (14),
vlan <vid> sip <ip> (15),
vlan <vid> dip <ip> (16),
vlan <vid> sport tcp|udp <port> (17),
vlan <vid> dport tcp|udp <port> (18),
vlan <vid> smac <mac> sip <ip> (19),
vlan <vid> dmac <mac> dip <ip> (20),
srcip <ip6>/<mask>|dstip <ip6/<mask>|tos <stos> <etos>|srcport <sport> <eport> |dstport <sport> <eport> (21),
vlan <vid> sip <ip6> (22),
vlan <vid> dip <ip6> (23)rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.2 |
aclProfileActionNumberProfile action number.
Bit 1: rate
Bit 2: rvlan
Bit 3: rpri
Bit 4: deny
Bit 1, Bit 2 & Bit 3 can multiple selection.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.3 |
aclProfileRuleParamMaskProfile rule parameter mask.
BIT 1: srcip <ip>/<mask>
BIT 2: dstip <ip>/<mask>
BIT 3: tos <stos> <etos>
BIT 4: srcport <sport> <eport>
BIT 5: dstport <sport> <eport>rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.4 |
aclProfileRuleEtypeProfile rule etype.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.5 |
aclProfileRuleVidProfile rule vid.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.6 |
aclProfileRuleSmacProfile rule source MAC.rw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.7 |
aclProfileRuleDmacProfile rule destination MAC.rw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.8 |
aclProfileRulePriorityProfile rule priority.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.9 |
aclProfileRuleProtocolProfile rule protocol.
icmp(1),igmp(2),ip(4),tcp(6),udp(17),gre(47),ospf(89), and other protocol types.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.10 |
aclProfileRuleSrcIPProfile rule source IPrw IpAddress .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.11 |
aclProfileRuleSrcIPMaskThe subnet mask of source IP mask.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.12 |
aclProfileRuleDestIPProfile rule source IP.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.13 |
aclProfileRuleDestIPMaskThe subnet mask of destination IP mask.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.14 |
aclProfileRuleStartTosProfile rule start type of service.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.15 |
aclProfileRuleEndTosProfile rule end type of service.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.16 |
aclProfileRuleSrcStartPortProfile rule source start port.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.17 |
aclProfileRuleSrcEndPortProfile rule source end port.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.18 |
aclProfileRuleDestStartPortProfile rule destination start port.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.19 |
aclProfileRuleDestEndPortProfile rule destination end port.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.20 |
aclProfileActionRateProfile action to replace to this rate.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.21 |
aclProfileActionrvlanProfile action to replace to this vlan.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.22 |
aclProfileActionrpriProfile action to replace to this priority.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.23 |
aclProfileRowStatusThe row status of the entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.24 |
aclProfileRuleSipSource IP.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.25 |
aclProfileRuleDipDestination IP.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.26 |
aclProfileRuleSportSource port.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.27 |
aclProfileRuleDportDestination port.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.28 |
aclProfileRuleSrcIp6srcip <ip6> for RuleNumber (21).rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.29 |
aclProfileRuleDstIp6dstip <ip6> for RuleNumber (21).rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.30 |
aclProfileRuleSip6sip <ip6> for RuleNumber (19), (22).rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.31 |
aclProfileRuleDip6dip <ip6> for RuleNumber (20), (23).rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.9.5.1.1.32 |
vdslProfile OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.9.6 |
maxNumOfVdslLineProfilesThe maximum number of VDSL line profiles supported by the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.6.1 |
maxNumOfVdslAlarmProfilesThe maximum number of VDSL alarm profiles supported by the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.6.2 |
vdslLineConfProfileExtendedTableThis table contains information on the VDSL line profile extension configuration.
This table is supported by R5.02 and later versions. SEQUENCE OF VdslLineConfProfileExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.9.6.3 |
vdslLineConfProfileExtendedEntryAn entry in vdslLineConfProfileExtendedTable. VdslLineConfProfileExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.9.6.3.1 |
vdsl2LConfProfRaModeDs(RA-MODEds).
The mode of operation of a rate-adaptive xTU-C in the transmit
direction. The parameter can take three values:
manual(1),
raInit(2),
dynamicRa(3).rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.6.3.1.1 |
vdsl2LConfProfRaModeUs(RA-MODEus).
The mode of operation of a rate-adaptive xTU-R in the transmit
direction. The parameter can take three values:
manual(1),
raInit(2),
dynamicRa(3).rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.6.3.1.2 |
vdsl2LConfProfRaUsNrmDs(RA-USNRMds).
The Downstream Up-Shift Noise Margin value, to be used when
xdsl2LConfProfRaModeDs is set to dynamicRa. If the downstream
noise margin is above this value and stays above it for
more than the time specified by the xdsl2LConfProfRaUsTimeDs,
the xTU-R shall attempt to increase the downstream net data
rate. The Downstream Up-shift Noise Margin ranges from 0 to
310 units of 0.1 dB (Physical values are 0 to 31 dB).rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.6.3.1.3 |
vdsl2LConfProfRaUsNrmUs(RA-USNRMus).
The Upstream Up-Shift Noise Margin value, to be used when
xdsl2LConfProfRaModeUs is set to dynamicRa. If the upstream
noise margin is above this value and stays above it for more
than the time specified by the xdsl2LConfProfRaUsTimeUs, the
xTU-C shall attempt to increase the upstream net data rate.
The Upstream Up-shift Noise Margin ranges from 0 to 310 units
of 0.1 dB (Physical values are 0 to 31 dB).rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.6.3.1.4 |
vdsl2LConfProfRaDsNrmDs(RA-DSNRMds).
The Downstream Down-Shift Noise Margin value, to be used when
xdsl2LConfProfRaModeDs is set to dynamicRa. If the downstream
noise margin is below this value and stays below that for more
than the time specified by the xdsl2LConfProfRaDsTimeDs, the
xTU-R shall attempt to decrease the downstream net data rate.
The Downstream Down-shift Noise Margin ranges from 0 to 310
units of 0.1 dB (Physical values are 0 to 31 dB).rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.6.3.1.5 |
vdsl2LConfProfRaDsNrmUs(RA-DSNRMus).
The Upstream Downshift Noise Margin value, to be used when
xdsl2LConfProfRaModeUs is set to dynamicRa. If the upstream
noise margin is below this value and stays below that for more
than the time specified by the xdsl2LConfProfRaDsTimeUs, the
xTU-C shall attempt to decrease the upstream net data rate.
The Upstream Down-shift Noise Margin ranges from 0 to 310
units of 0.1 dB (Physical values are 0 to 31 dB).rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.6.3.1.6 |
vdsl2LConfProfProfileNamero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.6.3.1.7 |
vdslLineAlarmConfProfileExtendedTableThis table contains information on the VDSL line alarm profile extension configuration.
This table is supported by R5.06 and later versions. SEQUENCE OF VdslLineAlarmConfProfileExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.9.6.4 |
vdslLineAlarmConfProfileExtendedEntryAn entry in vdslLineAlarmConfProfileExtendedTable. VdslLineAlarmConfProfileExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.9.6.4.1 |
vdslLAlarmConfProfProfileNamero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.6.4.1.1 |
voipProfile OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.9.7 |
sipProfile OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.9.7.1 |
maxNumOfSipProfilesThe maximum number of SIP profiles supported by the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.1.1 |
sipProfileTableThis table includes SIP protocol related configuration.
This table is supported by R4.01 and later versions. SEQUENCE OF SipProfileEntry .1.3.6.1.4.1.890.1.5.13.5.9.7.1.2 |
sipProfileEntryAn entry in sipProfileTable. SipProfileEntry .1.3.6.1.4.1.890.1.5.13.5.9.7.1.2.1 |
sipProfileNameThis object is used by the SIP profile table in order to identify a row of this table.ro DisplayString .1.3.6.1.4.1.890.1.5.13.5.9.7.1.2.1.1 |
sipProfileSipSvrIP used for SIP registration or SIP domain name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.7.1.2.1.2 |
sipProfileRegSvrRegistration server IP or registration server domain name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.7.1.2.1.3 |
sipProfileProxySvrProxy server IP or proxy server doamin name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.7.1.2.1.4 |
sipProfileSipPortSIP UA port number.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.1.2.1.5 |
sipProfileRegSvrPortRegistration server port number.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.1.2.1.6 |
sipProfileProxySvrPortProxy server port number.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.1.2.1.7 |
sipProfileUriTyperw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.1.2.1.8 |
sipProfilePbit802.1p bit for SIP and RTP packet.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.1.2.1.9 |
sipProfileDscpDSCP for SIP and RTP packet.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.1.2.1.10 |
sipProfileKeepAliverw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.1.2.1.11 |
sipProfileSeSession expiration time in seconds.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.1.2.1.12 |
sipProfilePrackrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.1.2.1.13 |
sipProfileRowStatusThis object is used to create a new row or delete an existing row in the table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.7.1.2.1.14 |
sipProfileReSendresend factor of session expiration time. This MIB object is supported by R5.05 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.1.2.1.15 |
sipProfileNonceCountKeepThis MIB object is supported by R5.05 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.1.2.1.16 |
sipProfileQopQuoteThis MIB object is supported by R5.05 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.1.2.1.17 |
sipProfileRefertobracketThis MIB object is supported by R5.05 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.1.2.1.18 |
sipProfileRefertodotThis MIB object is supported by R5.05 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.1.2.1.19 |
sipProfileRtpStartPortstart of RTP port number. This MIB object is supported by R5.05 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.1.2.1.20 |
sipProfileRtpEndPortend of RTP port number. This MIB object is supported by R5.05 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.1.2.1.21 |
maxNumOfSipCallSvcProfilesThe maximum number of SIP call service profiles supported by the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.1.3 |
sipCallSvcProfileTableThis table includes SIP call service related configuration.
This table is supported by R4.01 and later versions. SEQUENCE OF SipCallSvcProfileEntry .1.3.6.1.4.1.890.1.5.13.5.9.7.1.4 |
sipCallSvcProfileEntryAn entry in sipCallSvcProfileTable. SipCallSvcProfileEntry .1.3.6.1.4.1.890.1.5.13.5.9.7.1.4.1 |
sipCallSvcProfileNameThis object is used by the SIP call service profile table in order to identify a row of this table.ro DisplayString .1.3.6.1.4.1.890.1.5.13.5.9.7.1.4.1.1 |
sipCallSvcProfilePasswdOnPassword is necessary or not for SIP registration.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.1.4.1.2 |
sipCallSvcProfilePasswdSIP registration password.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.9.7.1.4.1.3 |
sipCallSvcProfileNumberPlanOnrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.1.4.1.4 |
sipCallSvcProfileNumberPlanCcCountry code, only digit 0..9 are allowed.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.9.7.1.4.1.5 |
sipCallSvcProfileNumberPlanNdcNational destination code, only digit 0..9 are allowed.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.9.7.1.4.1.6 |
sipCallSvcProfileNumberPlanTableNumbering plan table name.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.9.7.1.4.1.7 |
sipCallSvcProfileStateMaskBit 1 reserved : reserved
Bit 2 callhold : call hold
Bit 3 callwait : call waiting
Bit 4 callreturn : call return
Bit 5 calltransfer : call transfer
Bit 6 clip : caller line identification presentation (Caller ID)
Bit 7 clir : caller line identification restriction
Bit 8 dnd : do not disturb
Bit 9 registration
Bit 10 localcall
Bit 11 mwi : message waiting indicator
Bit 12 cidcw : caller identity with call waiting
Bit 13 conference
Bit 14 callsvcmode : europe(0) usa(1)
Bit 15 on hook transfer
Bit 16 conference transferrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.1.4.1.8 |
sipCallSvcProfileDtmfdtmf bypass : bypass DTMF tone
dtmf rfc2833 : DTMF tone relay according to RFC2833
dtmf rfc2833like : DTMF tone relay by SIP INFO message, but RFC2833 payload
dtmf sipinfo : DTMF tone relay by SIP INFO signal message
dtmf plaintext : DTMF tone relay by SIP INFO plain text messagerw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.1.4.1.9 |
sipCallSvcProfileFaxfax g711 : FAX service pass through by ITU-T G.711
fax t38 : FAX service by ITU-T T.38 UDP
fax t38rtp : FAX service by ITU-T T.38 RTPrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.1.4.1.10 |
sipCallSvcProfileRowStatusThis object is used to create a new row or delete an existing row in the table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.7.1.4.1.11 |
sipCallSvcProfileKeypatternKey pattern table name. This object is supported by R5.01 and later versions.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.9.7.1.4.1.12 |
sipCallSvcProfileRegTimeRegistration expiration time in seconds.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.1.4.1.13 |
sipCallSvcProfileFlashflash invite : send SIP INVITE message
flash rfc2833 : flash relay according to RFC2833
flash rfc2833like : flash relay by SIP INFO message, but RFC2833 payload
flash sipinfo1 : flash relay by SIP INFO signal=16 message
flash sipinfo2 : flash relay by SIP INFO signal=hf message
flash sipinfo3 : flash relay by SIP INFO signal=hook-flash message
flash sipinfo4 : flash relay by SIP INFO plain text message
flash sipinfo5 : flash relay by multiple SIP INFO signal messages and
signal content come from specified pattern string
flash sipinfo6 : flash relay by SIP INFO specified information messagerw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.1.4.1.14 |
sipCallSvcProfileFlashPatternrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.7.1.4.1.15 |
sipCallSvcProfileReanswerTimeReanswer time. The time period after user hangs up and before call is disconnected.rw INTEGER UNITS "seconds" .1.3.6.1.4.1.890.1.5.13.5.9.7.1.4.1.16 |
sipCallSvcProfileFirstDigitfirst digit timeout. This MIB object is supported by R5.05 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.1.4.1.17 |
sipCallSvcProfileInterdigitinter digit timeout. This MIB object is supported by R5.05 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.1.4.1.18 |
sipCallSvcProfileLocalHelpTableThis table is supported by R5.01 and later versions. SEQUENCE OF SipCallSvcProfileLocalHelpEntry .1.3.6.1.4.1.890.1.5.13.5.9.7.1.5 |
sipCallSvcProfileLocalHelpEntryAn entry in sipCallSvcProfileLocalHelpTable. SipCallSvcProfileLocalHelpEntry .1.3.6.1.4.1.890.1.5.13.5.9.7.1.5.1 |
sipCallSvcProfileLocalHelpIndexIndex number.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.1.5.1.1 |
sipCallSvcProfileLocalHelpTableNameLocal help table name.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.9.7.1.5.1.2 |
sipCallSvcProfileLocalHelpTableTelLocal help telephone number. Only digit characters are allowed.
Note that sipCallSvcProfileLocalHelpTableName and sipCallSvcProfileLocalHelpTableTel
must be set sequentially.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.9.7.1.5.1.3 |
maxNumOfSipDialPlanProfilesThe maximum number of SIP dial plan profiles supported by the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.1.6 |
sipDialPlanProfileTableConfigure dial plan related configuration of specified profile.
This table is supported by R5.01 and later versions. SEQUENCE OF SipDialPlanProfileEntry .1.3.6.1.4.1.890.1.5.13.5.9.7.1.7 |
sipDialPlanProfileEntryAn entry in sipDialPlanProfileTable. SipDialPlanProfileEntry .1.3.6.1.4.1.890.1.5.13.5.9.7.1.7.1 |
sipDialPlanProfileNameProfile name.ro DisplayString .1.3.6.1.4.1.890.1.5.13.5.9.7.1.7.1.1 |
sipDialPlanProfileIndexIndex number. 1-32 means dialplan pattern, 255 means default SIP server profile namero INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.1.7.1.2 |
sipDialPlanProfileDialPlanTableNameDial plan table name. 1-32 means dialplan pattern, 255 means default SIP server profile namerw DisplayString .1.3.6.1.4.1.890.1.5.13.5.9.7.1.7.1.3 |
sipDialPlanProfileRowStatusThis object is used to create a new row or delete an existing row in the table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.7.1.7.1.4 |
maxNumOfDspProfilesThe maximum number of DSP profiles supported by the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.2 |
dspProfileTableThis table includes DSP related configuration. This table is supported by R4.01 and later versions. SEQUENCE OF DspProfileEntry .1.3.6.1.4.1.890.1.5.13.5.9.7.3 |
dspProfileEntryAn entry in dspProfileTable. DspProfileEntry .1.3.6.1.4.1.890.1.5.13.5.9.7.3.1 |
dspProfileNameThis object is used by the DSP profile table in order to identify a row of this table.ro DisplayString .1.3.6.1.4.1.890.1.5.13.5.9.7.3.1.1 |
dspProfileCodecBit 1: g711a
Bit 2: g711mu
Bit 3: g723
Bit 4: g726-16
Bit 5: g726-24
Bit 6: g726-32
Bit 7: g726-40
Bit 8: g729abrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.3.1.2 |
dspProfilePlayBufferMinDelayPlay buffer minimum delay in milliseconds.
It should be less than or equal to dspProfilePlayBufferMaxDelay.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.3.1.3 |
dspProfilePlayBufferMaxDelayPlay buffer maximum delay in milliseconds.
It should be greater than or equal to dspProfilePlayBufferMinDelay.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.3.1.4 |
dspProfileEchoTailEcho cancellation echo tail period in milliseconds.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.3.1.5 |
dspProfileRowStatusThis object is used to create a new row or delete an existing row in the table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.7.3.1.6 |
dspProfileEchocancelOnEcho cancellation.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.3.1.7 |
dspProfileVadOnvoice activity detection.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.3.1.8 |
dspProfileg711vpiG.711 voice packet interval time in milliseconds.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.3.1.9 |
dspProfileg723vpiG.723 voice packet interval time in milliseconds.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.3.1.10 |
dspProfileg726vpiG.726 voice packet interval time in milliseconds.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.3.1.11 |
dspProfileg729vpiG.729 voice packet interval time in milliseconds.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.3.1.12 |
dspProfilePbitrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.3.1.13 |
dspProfileDscprw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.3.1.14 |
dspProfileCodecPriorityevery octet mean a codec, the order of octets means codec priority.
0x1: g711a
0x2: g711mu
0x3: g723
0x4: g726-16
0x5: g726-24
0x6: g726-32
0x7: g726-40
0x8: g729abrw DisplayString .1.3.6.1.4.1.890.1.5.13.5.9.7.3.1.15 |
h248Profile OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.9.7.4 |
maxNumOfH248ProfilesThe maximum number of H.248 profiles supported by the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.4.1 |
h248ProfileTableThis table includes H.248 protocol related configuration.
This table is supported by R5.01 and later versions. SEQUENCE OF H248ProfileEntry .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2 |
h248ProfileEntryAn entry in h248ProfileTable. H248ProfileEntry .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1 |
h248ProfileNameThis object is used by the H.248 profile table in order to identify a row of this table.ro DisplayString .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.1 |
h248ProfileMgcMGC IP or domain name.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.2 |
h248ProfileMgcPortMGC port number.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.3 |
h248ProfileMgc2OnSecondary MGC on/off.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.4 |
h248ProfileMgc2Secondary MGC IP or domain name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.5 |
h248ProfileMgc2PortSecondary MGC port.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.6 |
h248ProfileTransportTransport protocol.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.7 |
h248ProfileEncodeH.248 coding type.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.8 |
h248ProfilePbit802.1p bit for H.248 and RTP packet.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.9 |
h248ProfileDscpDSCP for H.248 and RTP packet.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.10 |
h248ProfileRowStatusThis object is used to create a new row or delete an existing row in the table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.11 |
h248ProfileSoftswitchThis MIB object is supported by R5.06 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.12 |
h248ProfileInactivityTimerThis MIB object is supported by R5.06 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.13 |
h248ProfilePrefixNameephemeral termination prefix, up to 31 characters.
This MIB object is supported by R5.06 and later versions.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.14 |
h248ProfileRtpPortStartstart port of RTP 4000 ~ 64000
This MIB object is supported by R5.06 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.15 |
h248ProfileRtpPortEndend port of RTP 5000 ~ 65000
This MIB object is supported by R5.06 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.16 |
h248ProfileInitRetranTimeinit retransmit time 100 ~ 20000 ms
This MIB object is supported by R5.06 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.17 |
h248ProfileMinRetranTimemin retransmit time 100 ~ 1000 ms
This MIB object is supported by R5.06 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.18 |
h248ProfileMaxRetranTimemax retransmit time 1000 ~ 20000 ms
This MIB object is supported by R5.06 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.19 |
h248ProfileRetranWindowretransmit window 1000 ~ 60000 ms
This MIB object is supported by R5.06 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.20 |
h248ProfileStartTimeoutstart timeout 0 ~ 99 seconds
This MIB object is supported by R5.06 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.21 |
h248ProfileShortTimeoutshort timeout 1 ~ 99 seconds
This MIB object is supported by R5.06 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.22 |
h248ProfileLongTimeoutlong timeout 1 ~ 99 seconds
This MIB object is supported by R5.06 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.23 |
h248ProfileVBDVBD mode support enable/disable
This MIB object is supported by R5.06 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.24 |
h248ProfileSuffixStartNumsuffix start number 1 ~ 15.
This MIB object is supported by R5.06 and later versions.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.25 |
h248ProfileSuffixSuffixLensuffix length 0 ~ 15
This MIB object is supported by R5.06 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.26 |
h248ProfileRFC2833rfc2833 mode support enable/disable
This MIB object is supported by R5.06 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.27 |
h248ProfileRFC2833PTrfc2833 payload type 96~127
This MIB object is supported by R5.06 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.28 |
h248ProfileT38fax t.38 mode support enable/disable
This MIB object is supported by R5.06 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.29 |
h248ProfileForceVersionforce using h.248 version 1
This MIB object is supported by R5.06 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.30 |
h248ProfileLocalcallTurn on the localcall utility
This MIB object is supported by R5.08 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.31 |
h248ProfileCallthroughTurn on the callthrough utility
This MIB object is supported by R5.08 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.7.4.2.1.32 |
ipqosProfile OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.9.8 |
maxNumOfIpqosProfilesThe maximum number of IPQOS profiles supported by the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.8.1 |
ipqosProfileTableThis table includes IPQOS related configuration. SEQUENCE OF IpqosProfileEntry .1.3.6.1.4.1.890.1.5.13.5.9.8.2 |
ipqosProfileEntryAn entry in ipqosProfileTable. IpqosProfileEntry .1.3.6.1.4.1.890.1.5.13.5.9.8.2.1 |
ipqosProfileNameThis object is used by the IPQOS profile table in order to identify a row of this table.ro DisplayString .1.3.6.1.4.1.890.1.5.13.5.9.8.2.1.1 |
ipqosProfileNumOfQueueThe number of IPQOS queues.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.8.2.1.2 |
ipqosProfileRowStatusThis object is used to create a new row or delete an existing row in the table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.8.2.1.3 |
ipqosProfileQueueTableThis table includes IPQOS queue related configuration. SEQUENCE OF IpqosProfileQueueEntry .1.3.6.1.4.1.890.1.5.13.5.9.8.3 |
ipqosProfileQueueEntryAn entry in ipqosProfileQueueTable. IpqosProfileQueueEntry .1.3.6.1.4.1.890.1.5.13.5.9.8.3.1 |
ipqosProfileQueueIndexIPQOS queue index.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.8.3.1.1 |
ipqosProfileQueuePIRPeak rate.rw INTEGER UNITS "Kbps" .1.3.6.1.4.1.890.1.5.13.5.9.8.3.1.2 |
ipqosProfileQueueCIRCommited rate.rw INTEGER UNITS "Kbps" .1.3.6.1.4.1.890.1.5.13.5.9.8.3.1.3 |
ipqosProfileQueuePBSPeak burst size.rw INTEGER UNITS "byte" .1.3.6.1.4.1.890.1.5.13.5.9.8.3.1.4 |
ipqosProfileQueueCBSCommited burst size.rw INTEGER UNITS "byts" .1.3.6.1.4.1.890.1.5.13.5.9.8.3.1.5 |
ipqosProfileQueueLevelQueue level.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.8.3.1.6 |
ipqosProfileQueueWeightQueue weight.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.8.3.1.7 |
rateLimitProfile OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.9.9 |
maxNumOfRateLimitProfilesThe maximum number of Rate Limit profiles supported by the system. This object is supported by R5.02 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.9.1 |
rateLimitProfileTableThis table includes Rate Limit related configuration. This table is supported by R5.02 and later versions. SEQUENCE OF RateLimitProfileEntry .1.3.6.1.4.1.890.1.5.13.5.9.9.2 |
rateLimitProfileEntryAn entry in rateLimitProfileTable. RateLimitProfileEntry .1.3.6.1.4.1.890.1.5.13.5.9.9.2.1 |
rateLimitProfileNameThis object is used by the Rate Limit profile table in order to identify a row of this table.ro DisplayString .1.3.6.1.4.1.890.1.5.13.5.9.9.2.1.1 |
rateLimitProfileIngressRateIngress rate between 0~100032 in kbps in step of 64, oo0oo means no limiting.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.9.2.1.2 |
rateLimitProfileEgressRateEgress rate between 0~100032 in kbps in step of 64, oo0oo means no limiting.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.9.2.1.3 |
rateLimitProfileRowStatusThis object is used to create a new row or delete an existing row in the table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.9.2.1.4 |
e1AlarmProfile OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.9.10 |
maxNumOfE1AlarmProfileThe maximum number of E1 Alarm profiles supported by the system. This object is supported by R5.03 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.10.1 |
e1AlarmProfileTableThis table includes Rate Limit related configuration. This table is supported by R5.03 and later versions. SEQUENCE OF E1AlarmProfileEntry .1.3.6.1.4.1.890.1.5.13.5.9.10.2 |
e1AlarmProfileEntryAn entry in e1AlarmProfileTable. E1AlarmProfileEntry .1.3.6.1.4.1.890.1.5.13.5.9.10.2.1 |
e1AlarmProfileNameThis object is used by the E1 Alarm profile table in order to identify a row of this table.ro DisplayString .1.3.6.1.4.1.890.1.5.13.5.9.10.2.1.1 |
e1AlarmProfileQEs15Min error secondrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.10.2.1.2 |
e1AlarmProfileQSes15Min severe error secondrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.10.2.1.3 |
e1AlarmProfileQUas15Min un-available secondrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.10.2.1.4 |
e1AlarmProfileDayEs1Day error secondrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.10.2.1.5 |
e1AlarmProfileDaySes1Day severe error secondrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.10.2.1.6 |
e1AlarmProfileDayUas1Day un-available secondrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.10.2.1.7 |
e1AlarmProfileRowStatusThis object is used to create a new row or delete an existing row in the table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.10.2.1.8 |
vdsl2Profile OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.9.11 |
maxNumOfVdsl2TemplateProfilesThe maximum number of VDSL2 template profiles supported by the system.
This MIB object is supported by R5.06 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.11.1 |
maxNumOfVdsl2LineProfilesThe maximum number of VDSL2 line profiles supported by the system.
This MIB object is supported by R5.06 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.11.2 |
maxNumOfVdsl2ChanProfilesThe maximum number of VDSL2 chan profiles supported by the system.
This MIB object is supported by R5.06 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.11.3 |
maxNumOfVdsl2AlarmTemplateProfilesThe maximum number of VDSL2 alarm template profiles supported by the system.
This MIB object is supported by R5.06 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.11.4 |
maxNumOfVdsl2AlarmLineProfilesThe maximum number of VDSL2 alarm line profiles supported by the system.
This MIB object is supported by R5.06 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.11.5 |
maxNumOfVdsl2AlarmChanProfilesThe maximum number of VDSL2 alarm chan profiles supported by the system.
This MIB object is supported by R5.06 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.11.6 |
vdsl2LineConfProfileExtendedTableThis table contains information on the VDSL2 line profile extension configuration.
This table is supported by R5.06 and later versions. SEQUENCE OF Vdsl2LineConfProfileExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.9.11.7 |
vdsl2LineConfProfileExtendedEntryAn entry in vdsl2LineProfileExtendedEntry. Vdsl2LineConfProfileExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1 |
vdsl2LineProfDpboEPsdIDstandard psd shape id for psd toolboxrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1.1 |
vdsl2LineProfBitSwapDsrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1.2 |
vdsl2LineProfBitSwapUsrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1.3 |
vdsl2LineProfProfileNamero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1.4 |
vdsl2LineProfDynamicDepthEnableDsEnable the dynamic change of interleave depth.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1.5 |
vdsl2LineProfDynamicDepthEnableUsEnable the dynamic change of interleave depth.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1.6 |
vdsl2LineProfSosTimeDsThe parameter SOS-TIME-ds is used in the specification of the receiver initiated SOS
(see 13.4.3/G.993.2). If the value of this parameter is not zero, the standard SOS
triggering criteria are enabled, and the value corresponds with duration of the time
window used in the standard SOS triggering criteria in the downstream direction.
See G.993.2 for detailed usage rules.
The special value zero indicates that the standard SOS triggering criteria are disabled,
i.e., vendor-discretionary values may be used instead of the values configured in the MIB
for the following parameters: SOS-NTONES-ds, SOS-CRC-ds, SOS-TIME-ds.
This parameter applies in the downstream direction. The valid range of non-zero values
is from 64 ms to 16320 ms in steps of 64 ms.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1.7 |
vdsl2LineProfSosTimeUsThe parameter SOS-TIME-u s is used in the specification of the receiver initiated SOS
(see 13.4.3/G.993.2). If the value of this parameter is not zero, the standard SOS
triggering criteria are enabled, and the value corresponds with duration of the time
window used in the standard SOS triggering criteria in the downstream direction.
See G.993.2 for detailed usage rules.
The special value zero indicates that the standard SOS triggering criteria are disabled,
i.e., vendor-discretionary values may be used instead of the values configured in the MIB
for the following parameters: SOS-NTONES-ds, SOS-CRC-ds, SOS-TIME-ds.
This parameter applies in the downstream direction. The valid range of non-zero values
is from 64 ms to 16320 ms in steps of 64 ms.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1.8 |
vdsl2LineProfSosCrcDsThis parameter is defined as the minimum number of normalized CRC anomalies received
in SOS-TIME-ds seconds in order to arm the second sub condition of the standard SOS
triggering criteria (see 13.4.3.2/G.993.2) in the downstream direction. See G.993.2
for detailed usage rules. The valid range of SOS-CRC values is 0.02 to ((2^16)-1)*0.02,
in steps of 0.02.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1.9 |
vdsl2LineProfSosCrcUsThis parameter is defined as the minimum number of normalized CRC anomalies received
in SOS-TIME-ds seconds in order to arm the second sub condition of the standard SOS
triggering criteria (see 13.4.3.2/G.993.2) in the downstream direction. See G.993.2
for detailed usage rules. The valid range of SOS-CRC values is 0.02 to ((2^16)-1)*0.02,
in steps of 0.02.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1.10 |
vdsl2LineProfSosNToneDsThis parameter is defined as the minimum percentage of tones in the downstream
MEDLEY SET that must be degraded in order to arm the first sub-condition of the
standard SOS triggering criteria (see 13.4.3.2/G.993.2) in the downstream direction.
The parameter SOS-NTONES-ds is defined as a percentage of tones. See G.993.2 for
detailed usage rules. The valid range of values is from 1 to 100 in steps of 1.
Use of the special value 0 is described in 13.4.3.2/G.993.2.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1.11 |
vdsl2LineProfSosNToneUsThis parameter is defined as the minimum percentage of tones in the downstream
MEDLEY SET that must be degraded in order to arm the first sub-condition of the
standard SOS triggering criteria (see 13.4.3.2/G.993.2) in the downstream direction.
The parameter SOS-NTONES-ds is defined as a percentage of tones. See G.993.2 for
detailed usage rules. The valid range of values is from 1 to 100 in steps of 1.
Use of the special value 0 is described in 13.4.3.2/G.993.2.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1.12 |
vdsl2LineProfSosMaxDsThis parameter is used in G.993.2 de-activation (see 12.1.4/G.993.2). If the number
of successful SOS procedures in the downstream direction performed within a 120-second
interval exceeds MAX-SOS-ds, the modem shall transition to the L3 state. See G.993.2
for detailed usage rules (see 12.1.4/G.993.2). The valid range of values is 1 to 15.
Use of the special value 0 is described in 12.1/G.993.2.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1.13 |
vdsl2LineProfSosMaxUsThis parameter is used in G.993.2 de-activation (see 12.1.4/G.993.2). If the number
of successful SOS procedures in the downstream direction performed within a 120-second
interval exceeds MAX-SOS-ds, the modem shall transition to the L3 state. See G.993.2
for detailed usage rules (see 12.1.4/G.993.2). The valid range of values is 1 to 15.
Use of the special value 0 is described in 12.1/G.993.2.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1.14 |
vdsl2LineProfSosMultiStepDsIndicates the capabilities of the VTU-R to execute the SOS request in one step or in
multiple steps in the downstream direction. The field is formatted as [gggg 0000].
The first four MSBs [gggg] indicate the maximum number of tones (GSOS) that can be
executed in a single step (GSOS)in the downstream direction. The valid values are:
- [0000]: No limitation
- [0010]: GSOS = 256 tones
- [0011]: GSOS = 512 tones
- [0100]: GSOS = 1024 tonesrw BITS .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1.15 |
vdsl2LineProfSosMultiStepUsIndicates the capabilities of the VTU-R to execute the SOS request in one step or in
multiple steps in the downstream direction. The field is formatted as [gggg 0000].
The first four MSBs [gggg] indicate the maximum number of tones (GSOS) that can be
executed in a single step (GSOS)in the downstream direction. The valid values are:
- [0000]: No limitation
- [0010]: GSOS = 256 tones
- [0011]: GSOS = 512 tones
- [0100]: GSOS = 1024 tonesrw BITS .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1.16 |
vdsl2LineProfRocEnableDsEnable the robust overhead channel.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1.17 |
vdsl2LineProfRocEnableUsEnable the robust overhead channel.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1.18 |
vdsl2LineProfRocSnrmDsThe parameter is defined as the SNR margin offset for the ROC channel in the downstream
direction. The parameter is used in the specification of the channel initialization
policy (see 12.3.7.1/G.993.2).
The valid range of SNR margin offset values is from 0 to 31 dB with 0.1 dB steps.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1.19 |
vdsl2LineProfRocSnrmUsThe parameter is defined as the SNR margin offset for the ROC channel in the downstream
direction. The parameter is used in the specification of the channel initialization
policy (see 12.3.7.1/G.993.2).
The valid range of SNR margin offset values is from 0 to 31 dB with 0.1 dB steps.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1.20 |
vdsl2LineProfRocMinInpDsThis parameter contains the minimum impulse noise protection to apply on the ROC in the
downstream direction. The minimum impulse noise protection is an integer ranging from
0 to 16.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1.21 |
vdsl2LineProfRocMinInpUsThis parameter contains the minimum impulse noise protection to apply on the ROC in the
downstream direction. The minimum impulse noise protection is an integer ranging from
0 to 16.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1.22 |
vdsl2LineProfDpboTyperw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1.23 |
vdsl2LineProfDpboEselMinrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1.24 |
vdsl2LineProfCompatibleCompatible to spectrum usage of adsl2 or adsl2+ line.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1.25 |
vdsl2LineProfTransmissionTypeConfigure the desired transmission types. They are:
vdsl2(0)
adsl2+(1)
adsl2(2)
gdmt(3)
t1413(4)
glite(5)
annex-m(6)
annex-l(7)rw BITS .1.3.6.1.4.1.890.1.5.13.5.9.11.7.1.26 |
vdsl2ChanConfProfileExtendedTableThis table contains information on the VDSL2 channel profile extension configuration.
This table is supported by R5.06 and later versions. SEQUENCE OF Vdsl2ChanConfProfileExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.9.11.8 |
vdsl2ChanConfProfileExtendedEntryAn entry in vdsl2ChanConfProfileExtendedEntry. Vdsl2ChanConfProfileExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1 |
vdsl2ChanConfProfphyRdsretransmission moderw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.1 |
vdsl2ChanConfProfphyRusretransmission moderw Enumeration .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.2 |
vdsl2ChanConfProfProfileNamero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.3 |
vdsl2ChanConfProfGinpRtxModeDsG.inp(G.998.4) support setting on downstream direction.
The possible values are:
Forbidden(0) - Support for G998.4 is disabled.
Preferred(1) - If G998.4 is supported by the far-end, it is enabled.
Forced(2) - The line will only train if G998.4 can be enabled.
Test(3) - G998.4 is enabled in test mode (refer to G998.4, Clause 10.4).rw Xdsl2ConfigRtxMode .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.4 |
vdsl2ChanConfProfGinpRtxModeUsG.inp(G.998.4) support setting on upstream direction.
The possible values are:
Forbidden(0) - Support for G998.4 is disabled.
Preferred(1) - If G998.4 is supported by the far-end, it is enabled.
Forced(2) - The line will only train if G998.4 can be enabled.
Test(3) - G998.4 is enabled in test mode (refer to G998.4, Clause 10.4).rw Xdsl2ConfigRtxMode .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.5 |
vdsl2ChanConfProfGinpEtrMaxDsDefines the maximum allowed value for the ETR (Effective Throughput Rate).rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.6 |
vdsl2ChanConfProfGinpEtrMaxUsDefines the maximum allowed value for the ETR (Effective Throughput Rate).rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.7 |
vdsl2ChanConfProfGinpEtrMinDsDefines the minimum value for the ETR (Effective Throughput Rate).rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.8 |
vdsl2ChanConfProfGinpEtrMinUsDefines the minimum value for the ETR (Effective Throughput Rate).rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.9 |
vdsl2ChanConfProfGinpNdrMaxDsOverrules the wanted maximum data rate provided in the SetLineTrafficConfigurationrw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.10 |
vdsl2ChanConfProfGinpNdrMaxUsOverrules the wanted maximum data rate provided in the SetLineTrafficConfigurationrw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.11 |
vdsl2ChanConfProfGinpShineRatioDsThe assumed fraction (0.001 to 0.255) of NDR necessary to correct SHINE noise.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.12 |
vdsl2ChanConfProfGinpShineRatioUsThe assumed fraction (0.001 to 0.255) of NDR necessary to correct SHINE noise.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.13 |
vdsl2ChanConfProfGinpLeftrThresholdDsThe rate threshold (fraction of NDR) below which the Low Error Free Rate (LEFTR) defect is declared.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.14 |
vdsl2ChanConfProfGinpLeftrThresholdUsThe rate threshold (fraction of NDR) below which the Low Error Free Rate (LEFTR) defect is declared.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.15 |
vdsl2ChanConfProfGinpMaxDelayDsG.inp-specific value that overrules the traffic configuration setting.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.16 |
vdsl2ChanConfProfGinpMaxDelayUsG.inp-specific value that overrules the traffic configuration setting.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.17 |
vdsl2ChanConfProfGinpMinDelayDsG.inp-specific value that overrules the traffic configuration setting.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.18 |
vdsl2ChanConfProfGinpMinDelayUsG.inp-specific value that overrules the traffic configuration setting.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.19 |
vdsl2ChanConfProfGinpInpMinDsG.inp-specific value that overrules the traffic configuration setting. Unit is symbol.
The possible values are: 0-31rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.20 |
vdsl2ChanConfProfGinpInpMinUsG.inp-specific value that overrules the traffic configuration setting. Unit is symbol.
The possible values are: 0-31rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.21 |
vdsl2ChanConfProfGinpReinCfgInpDsG.inp-specific value that overrules the traffic configuration setting. Unit is symbol.
The possible values are: 0-7rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.22 |
vdsl2ChanConfProfGinpReinCfgInpUsG.inp-specific value that overrules the traffic configuration setting. Unit is symbol.
The possible values are: 0-7rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.23 |
vdsl2ChanConfProfGinpReinCfgFreqDsG.inp-specific value that overrules the traffic configuration setting. Unit is Hz.
The possible values are:
100 - 100Hz
120 - 120Hzrw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.24 |
vdsl2ChanConfProfGinpReinCfgFreqUsG.inp-specific value that overrules the traffic configuration setting. Unit is Hz.
The possible values are:
100 - 100Hz
120 - 120Hzrw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.25 |
vdsl2ChanConfProfSosMinRateB0DsThis parameter specifies the minimum net data rate required for a valid SOS request
in the downstream direction. The value shall be coded as an unsigned integer representing
the data rate as a multiple of 8 kbit/s.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.26 |
vdsl2ChanConfProfSosMinRateB0UsThis parameter specifies the minimum net data rate required for a valid SOS request
in the downstream direction. The value shall be coded as an unsigned integer representing
the data rate as a multiple of 8 kbit/s.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.8.1.27 |
vdsl2LineAlarmConfProfileExtendedTableThis table contains information on the VDSL2 line alarm profile extension configuration.
This table is supported by R5.06 and later versions. SEQUENCE OF Vdsl2LineAlarmConfProfileExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.9.11.9 |
vdsl2LineAlarmConfProfileExtendedEntryAn entry in vdsl2LineAlarmConfProfileExtendedEntry. Vdsl2LineAlarmConfProfileExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.9.11.9.1 |
xdsl2LineAlarmConfProfileXtucThresh15MinLofsA threshold for the xdsl2PMLCurr15MLofs counter, when xdsl2PMLCurrUnit is xtuc 1.
The value 0 means that no threshold is specified for the associated counter.
Units:secondsrw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.9.1.1 |
xdsl2LineAlarmConfProfileXturThresh15MinLofsA threshold for the xdsl2PMLCurr15MLofs counter, when xdsl2PMLCurrUnit is xtur 2.
The value 0 means that no threshold is specified for the associated counter.
Units:secondsrw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.9.1.2 |
xdsl2LineAlarmConfProfileThresh15MinLprsA threshold for the xdsl2PMLCurr15MLprs counter.
The value 0 means that no threshold is specified for the associated counter.
Units:secondsrw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.9.1.3 |
xdsl2LineAlarmConfProfileProfileNamero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.11.9.1.4 |
xdsl2LineAlarmConfProfileXtucThresh15MinLolsA threshold for the xdsl2PMLCurr15MLols counter, when xdsl2PMLCurrUnit is xtuc.
The value 0 means that no threshold is specified for the associated counter.
Units:secondsrw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.9.1.5 |
vdsl2LineConfTempExtendedTableThis table contains information on the VDSL2 line template profile extension configuration.
This table is supported by R5.06 and later versions. SEQUENCE OF Vdsl2LineConfTempExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.9.11.10 |
vdsl2LineConfTempExtendedEntryAn entry in vdsl2LineConfTempExtendedTable. Vdsl2LineConfTempExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.9.11.10.1 |
vdsl2LineConfTempTemplateNamero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.11.10.1.1 |
vdsl2LineConfTempTemplatePortMapProfile mapping port listro PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.9.11.10.1.2 |
vdsl2LineConfTempInmProfilerw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.11.10.1.3 |
vdsl2AlarmConfTempExtendedTableThis table contains information on the VDSL2 line alarm template profile extension configuration.
This table is supported by R5.06 and later versions. SEQUENCE OF Vdsl2AlarmConfTempExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.9.11.11 |
vdsl2AlarmConfTempExtendedEntryAn entry in vdsl2AlarmConfTempExtendedTable. Vdsl2AlarmConfTempExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.9.11.11.1 |
vdsl2AlarmConfTempTemplateNamero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.11.11.1.1 |
vdsl2ChanAlarmConfProfileExtendedTableThis table contains information on the VDSL2 channel alarm profile extension configuration.
This table is supported by R5.06 and later versions. SEQUENCE OF Vdsl2ChanAlarmConfProfileExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.9.11.12 |
vdsl2ChanAlarmConfProfileExtendedEntryAn entry in vdsl2ChanAlarmConfProfileExtendedTable. Vdsl2ChanAlarmConfProfileExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.9.11.12.1 |
vdsl2ChanAlarmConfProfProfileNamero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.11.12.1.1 |
maxNumOfVdsl2InmProfilesThe maximum number of VDSL2 Inm profiles supported by the system.
This MIB object is supported by R5.06 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.11.13 |
vdsl2InmConfProfileExtendedTablevdsl2InmConfProfileExtendedTable. SEQUENCE OF Vdsl2InmConfProfileExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.9.11.14 |
vdsl2InmConfProfileExtendedEntryvdsl2InmConfProfileExtendedTable. Vdsl2InmConfProfileExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.9.11.14.1 |
xdsl2InmConfProfProfileNameThis object identifies a row in this table. DisplayString .1.3.6.1.4.1.890.1.5.13.5.9.11.14.1.1 |
xdsl2InmConfProfVtucInpEqThe INM Inmpulse Noise Protection Equivalent Mode.
Configuration parameter INM-INPEQ-MODE defines the way of
computation of Equivalent INP, as defined in ITU-T G.993.2 Amd2
11.4.2.2.1
This takes a value in the range from 0 to 3.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.14.1.2 |
xdsl2InmConfProfVturInpEqThe INM Inmpulse Noise Protection Equivalent Mode.
Configuration parameter INM-INPEQ-MODE defines the way of
computation of Equivalent INP, as defined in ITU-T G.993.2 Amd2
11.4.2.2.1
This takes a value in the range from 0 to 3.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.14.1.3 |
xdsl2InmConfProfVtucCCThe INM Cluster Continuation. The valid values for INMCC range
from 0 from 64 DMT symbols in steps of 1 DMT symbol.
Up to and including INMCC nondegraded symbols will be allowed before
a cluster is deemed to be complete and the impulse noise event over.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.14.1.4 |
xdsl2InmConfProfVturCCThe INM Cluster Continuation. The valid values for INMCC range
from 0 from 64 DMT symbols in steps of 1 DMT symbol.
Up to and including INMCC nondegraded symbols will be allowed before
a cluster is deemed to be complete and the impulse noise event over.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.14.1.5 |
xdsl2InmConfProfVtucIATOThe INM Inter Arrival Time Offset for the IAT anomaly generation.
The valid values for INMIATO range from 3 from 511 DMT symbols in steps
of 1 DMT symbol.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.14.1.6 |
xdsl2InmConfProfVturIATOThe INM Inter Arrival Time Offset for the IAT anomaly generation.
The valid values for INMIATO range from 3 from 511 DMT symbols in steps
of 1 DMT symbol.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.14.1.7 |
xdsl2InmConfProfVtucIATSThe INM Inter Arrival Time Step for the IAT anomaly generation.
The valid values for INMIATS range from 0 from 7 in steps. The range of
values of inter-arrival times recorded in a single bin is 2^(INMIATS).
All inter-arrival times greater than or equal to INMIATO+6*(2^INMIATS)
are recorded in the 7th bin of INMAIAT.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.14.1.8 |
xdsl2InmConfProfVturIATSThe INM Inter Arrival Time Step for the IAT anomaly generation.
The valid values for INMIATS range from 0 from 7 in steps. The range of
values of inter-arrival times recorded in a single bin is 2^(INMIATS).
All inter-arrival times greater than or equal to INMIATO+6*(2^INMIATS)
are recorded in the 7th bin of INMAIAT.rw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.9.11.14.1.9 |
xdsl2InmConfProfRowStatusThis object is used to create a new row or to modify or
delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.11.14.1.10 |
xdsl2InmConfProfVtucISDBUSISDD sensitivity of VTU-C, -128~127 in unit of 0.1dB.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.11.14.1.11 |
queueRateLimitProfile OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.9.12 |
maxNumOfQueueRateLimitProfilesThe maximum number of Queue Rate Limit profiles supported by the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.12.1 |
queueRateLimitProfileTableThis table includes Queue Rate Limit related configuration. SEQUENCE OF QueueRateLimitProfileEntry .1.3.6.1.4.1.890.1.5.13.5.9.12.2 |
queueRateLimitProfileEntryAn entry in queueRateLimitProfileTable. QueueRateLimitProfileEntry .1.3.6.1.4.1.890.1.5.13.5.9.12.2.1 |
queueRateLimitProfileNameThis object is used by the Queue Rate Limit profile table and Queue Rate Limit Profile Queue table in order to identify a row of these table.ro DisplayString .1.3.6.1.4.1.890.1.5.13.5.9.12.2.1.1 |
queueRateLimitProfileQueue0CIRCIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.12.2.1.2 |
queueRateLimitProfileQueue0PIRPIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.12.2.1.3 |
queueRateLimitProfileQueue1CIRCIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.12.2.1.4 |
queueRateLimitProfileQueue1PIRPIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.12.2.1.5 |
queueRateLimitProfileQueue2CIRCIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.12.2.1.6 |
queueRateLimitProfileQueue2PIRPIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.12.2.1.7 |
queueRateLimitProfileQueue3CIRCIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.12.2.1.8 |
queueRateLimitProfileQueue3PIRPIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.12.2.1.9 |
queueRateLimitProfileQueue4CIRCIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.12.2.1.10 |
queueRateLimitProfileQueue4PIRPIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.12.2.1.11 |
queueRateLimitProfileQueue5CIRCIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.12.2.1.12 |
queueRateLimitProfileQueue5PIRPIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.12.2.1.13 |
queueRateLimitProfileQueue6CIRCIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.12.2.1.14 |
queueRateLimitProfileQueue6PIRPIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.12.2.1.15 |
queueRateLimitProfileQueue7CIRCIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.12.2.1.16 |
queueRateLimitProfileQueue7PIRPIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.12.2.1.17 |
queueRateLimitProfileRowStatusThis object is used to create a new row or delete an existing row in the table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.12.2.1.18 |
ipqos2Profile OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.9.13 |
maxNumOfIpqos2ProfilesThe maximum number of IPQoS2 profiles supported by the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.1 |
ipqos2ProfileTableThis table includes IPQoS2 profiles. SEQUENCE OF Ipqos2ProfileEntry .1.3.6.1.4.1.890.1.5.13.5.9.13.2 |
ipqos2ProfileEntryAn entry in ipqos2ProfileTable. Ipqos2ProfileEntry .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1 |
ipqos2ProfileNameprofile name.ro DisplayString .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.1 |
ipqos2ProfileAlgorithm1:sp, 2:wfq, 3-sp+wfq, 4:shaping, 5:vc-shaping.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.2 |
ipqos2ProfileVcLevellevel of the PVC. For vc-shaping only. Displayed as -1 when ipqos2ProfileAlgorithm
is not vc-shaping.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.3 |
ipqos2ProfileVcMaxRatemax rate of the queues of PVCs. For vc-shaping only. Displayed as -1 when ipqos2ProfileAlgorithm
is not vc-shaping.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.4 |
ipqos2ProfileVcDepthdepth of queues of PVCs. For vc-shaping only. Displayed as -1 when ipqos2ProfileAlgorithm
is not vc-shaping.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.5 |
ipqos2ProfileQueue0Weightweight of queue 0 of PVCs. For wfq, sp+wfq only. Displayed as -1 when ipqos2ProfileAlgorithm
is not wfq, sp+wfq.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.6 |
ipqos2ProfileQueue0MaxRatemax rate of queue 0 of PVCs. For shaping only. Displayed as -1 when ipqos2ProfileAlgorithm
is not shaping.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.7 |
ipqos2ProfileQueue0Depthdepth of queue 0 of PVCs. For wfq, sp+wfq, shaping. Displayed as -1 when ipqos2ProfileAlgorithm
is not wfq, sp+wfq, shaping.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.8 |
ipqos2ProfileQueue1Weightweight of queue 1 of PVCs. For wfq, sp+wfq only. Displayed as -1 when ipqos2ProfileAlgorithm
is not wfq, sp+wfq.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.9 |
ipqos2ProfileQueue1MaxRatemax rate of queue 1 of PVCs. For shaping only. Displayed as -1 when ipqos2ProfileAlgorithm
is not shaping.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.10 |
ipqos2ProfileQueue1Depthdepth of queue 1 of PVCs. For wfq, sp+wfq, shaping. Displayed as -1 when ipqos2ProfileAlgorithm
is not wfq, sp+wfq, shaping.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.11 |
ipqos2ProfileQueue2Weightweight of queue 2 of PVCs. For wfq, sp+wfq only. Displayed as -1 when ipqos2ProfileAlgorithm
is not wfq, sp+wfq.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.12 |
ipqos2ProfileQueue2MaxRatemax rate of queue 2 of PVCs. For shaping only. Displayed as -1 when ipqos2ProfileAlgorithm
is not shaping.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.13 |
ipqos2ProfileQueue2Depthdepth of queue 2 of PVCs. For wfq, sp+wfq, shaping. Displayed as -1 when ipqos2ProfileAlgorithm
is not wfq, sp+wfq, shaping.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.14 |
ipqos2ProfileQueue3Weightweight of queue 3 of PVCs. For wfq, sp+wfq only. Displayed as -1 when ipqos2ProfileAlgorithm
is not wfq, sp+wfq.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.15 |
ipqos2ProfileQueue3MaxRatemax rate of queue 3 of PVCs. For shaping only. Displayed as -1 when ipqos2ProfileAlgorithm
is not shaping.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.16 |
ipqos2ProfileQueue3Depthdepth of queue 3 of PVCs. For wfq, sp+wfq, shaping. Displayed as -1 when ipqos2ProfileAlgorithm
is not wfq, sp+wfq, shaping.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.17 |
ipqos2ProfileQueue4Weightweight of queue 4 of PVCs. For wfq, sp+wfq only. Displayed as -1 when ipqos2ProfileAlgorithm
is not wfq, sp+wfq.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.18 |
ipqos2ProfileQueue4MaxRatemax rate of queue 4 of PVCs. For shaping only. Displayed as -1 when ipqos2ProfileAlgorithm
is not shaping.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.19 |
ipqos2ProfileQueue4Depthdepth of queue 4 of PVCs. For wfq, sp+wfq, shaping. Displayed as -1 when ipqos2ProfileAlgorithm
is not wfq, sp+wfq, shaping.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.20 |
ipqos2ProfileQueue5Weightweight of queue 5 of PVCs. For wfq, sp+wfq only. Displayed as -1 when ipqos2ProfileAlgorithm
is not wfq, sp+wfq, shaping.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.21 |
ipqos2ProfileQueue5MaxRatemax rate of queue 5 of PVCs. For shaping only. Displayed as -1 when ipqos2ProfileAlgorithm
is not shaping.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.22 |
ipqos2ProfileQueue5Depthdepth of queue 5 of PVCs. For wfq, sp+wfq, shaping. Displayed as -1 when ipqos2ProfileAlgorithm
is not wfq, sp+wfq, shaping.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.23 |
ipqos2ProfileQueue6Weightweight of queue 6 of PVCs. For wfq, sp+wfq only. Displayed as -1 when ipqos2ProfileAlgorithm
is not wfq, sp+wfq.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.24 |
ipqos2ProfileQueue6MaxRatemax rate of queue 6 of PVCs. For shaping only. Displayed as -1 when ipqos2ProfileAlgorithm
is not shaping.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.25 |
ipqos2ProfileQueue6Depthdepth of queue 6 of PVCs. For wfq, sp+wfq, shaping. Displayed as -1 when ipqos2ProfileAlgorithm
is not wfq, sp+wfq, shaping.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.26 |
ipqos2ProfileQueue7Weightweight of queue 7 of PVCs. For wfq, sp+wfq only. Displayed as -1 when ipqos2ProfileAlgorithm
is not wfq, sp+wfq.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.27 |
ipqos2ProfileQueue7MaxRatemax rate of queue 7 of PVCs. For shaping only. Displayed as -1 when ipqos2ProfileAlgorithm
is not shaping.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.28 |
ipqos2ProfileQueue7Depthdepth of queue 7 of PVCs. For wfq, sp+wfq, shaping. Displayed as -1 when ipqos2ProfileAlgorithm
is not wfq, sp+wfq, shaping.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.29 |
ipqos2ProfileRowStatusThis object is used to create a new row or delete an existing row in the table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.9.13.2.1.30 |
switch OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.10 |
managementVLANIdThe VLAN ID for management.rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.10.1 |
maxNumOfStaticVlansThe maximum number of VLANs supported by the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.2 |
enetport OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.10.3 |
enetPortTableThe table contains ethernet port information. SEQUENCE OF EnetPortEntry .1.3.6.1.4.1.890.1.5.13.5.10.3.1 |
enetPortEntry EnetPortEntry .1.3.6.1.4.1.890.1.5.13.5.10.3.1.1 |
enetPortSpeedSpeed configuration of the ethernet port.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.3.1.1.1 |
enetPortFlowControlEnable/disable flow control for the ethernet port.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.3.1.1.2 |
enetPortModeThe operational mode for uplink and subtending ports.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.3.1.1.3 |
enetPortVLANTrunkEnableEnable/disable VLAN trunking for the ethernet port.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.3.1.1.4 |
enetPortDscpEnableEnable/disable DSCP mapping for the ethernet port.
This object is supported by R1.02 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.3.1.1.5 |
enetPortTpidSet TPID value for the ethernet port,
0x0000 ~ 0xffff.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.3.1.1.6 |
enetPortSfpTableThe table contains ethernet SFP port information. SEQUENCE OF EnetPortSfpEntry .1.3.6.1.4.1.890.1.5.13.5.10.3.2 |
enetPortSfpEntry EnetPortSfpEntry .1.3.6.1.4.1.890.1.5.13.5.10.3.2.1 |
sfpTempLowtemperature low threshold in 0.001 degree.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.3.2.1.1 |
sfpTempHightemperature high threshold in 0.001 degree.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.3.2.1.2 |
sfpVccLowvoltage low threshold in mV.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.3.2.1.3 |
sfpVccHighvoltage high threshold in mV.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.3.2.1.4 |
sfpTxBiasLowbias current low threshold in uA.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.3.2.1.5 |
sfpTxBiasHighbias current high threshold in uA.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.3.2.1.6 |
sfpTxPowerLowtx power low threshold in 0.001 uW.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.3.2.1.7 |
sfpTxPowerHightx power high threshold in 0.001 uW.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.3.2.1.8 |
sfpRxPowerLowtx power low threshold in 0.001 uW.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.3.2.1.9 |
sfpRxPowerHightx power high threshold in 0.001 uW.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.3.2.1.10 |
bandwidth OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.10.4 |
bwPortTableThe table contains bandwidth configuration for the ethernet ports. SEQUENCE OF BwPortEntry .1.3.6.1.4.1.890.1.5.13.5.10.4.1 |
bwPortEntry BwPortEntry .1.3.6.1.4.1.890.1.5.13.5.10.4.1.1 |
bwPortEnableEnable/disable bandwidth control for the ethernet port.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.4.1.1.1 |
bwPortIngressRateThe ingress rate for the ethernet port.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.4.1.1.2 |
bwPortEgressRateThe egress rate for the ethernet port.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.4.1.1.3 |
qschedule OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.10.5 |
qschedulePortTableThe table contains queue schedule configuration for the ethernet ports. SEQUENCE OF QschedulePortEntry .1.3.6.1.4.1.890.1.5.13.5.10.5.1 |
qschedulePortEntry QschedulePortEntry .1.3.6.1.4.1.890.1.5.13.5.10.5.1.1 |
qschedulePortTypeQueue scheduling type (strictly priority queue or weighted round robin).rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.5.1.1.1 |
queueWeightTableThe table contains weight configuration for the priority queues. SEQUENCE OF QueueWeightEntry .1.3.6.1.4.1.890.1.5.13.5.10.5.2 |
queueWeightEntry QueueWeightEntry .1.3.6.1.4.1.890.1.5.13.5.10.5.2.1 |
queueWeightWeight for the priority queue.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.5.2.1.1 |
dot3ad OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.10.6 |
dot3adTableThe table contains 802.3ad configuration. SEQUENCE OF Dot3adEntry .1.3.6.1.4.1.890.1.5.13.5.10.6.1 |
dot3adEntry Dot3adEntry .1.3.6.1.4.1.890.1.5.13.5.10.6.1.1 |
dot3adGroupIdGroup ID 1 for subtending group and 2 for uplink group in IES-5000/5005.
Group ID 1~4 in IES-6000.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.6.1.1.1 |
dot3adEnableEnable/disable 802.3ad function.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.6.1.1.2 |
dot3adGroupNameThe trunking group name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.10.6.1.1.3 |
dot3adGroupPortListThe port list which joins the trunking group.ro PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.10.6.1.1.4 |
lacpPriorityLACP system priority.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.6.2 |
lacpTimeoutThe time interval to exchange LACP packets in order to check that the peer port
in the trunk group is still up.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.6.3 |
portTrunkingTableThe table contains current status of port trunking. SEQUENCE OF PortTrunkingEntry .1.3.6.1.4.1.890.1.5.13.5.10.6.4 |
portTrunkingEntryAn entry of portTrunkingTable. PortTrunkingEntry .1.3.6.1.4.1.890.1.5.13.5.10.6.4.1 |
portTrunkingGroupIdGroup ID 1 for subtending group and 2 for uplink group in IES-5000/5005.
Group ID 1~4 in IES-6000.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.6.4.1.1 |
portTrunkingStatusPort trunking status.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.6.4.1.2 |
portTrunkingPortListThe port list which actually joins the trunking group.ro PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.10.6.4.1.3 |
aggPortTableThe table specifies the setting of port trunking. SEQUENCE OF AggPortEntry .1.3.6.1.4.1.890.1.5.13.5.10.6.5 |
aggPortEntryAn entry of aggPortTable. AggPortEntry .1.3.6.1.4.1.890.1.5.13.5.10.6.5.1 |
aggPortJoinJoin/disjoin the trunking group.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.6.5.1.1 |
elcPortTrunkingTableThe table is supported by R5.01 and later versions. SEQUENCE OF ElcPortTrunkingEntry .1.3.6.1.4.1.890.1.5.13.5.10.6.6 |
elcPortTrunkingEntry ElcPortTrunkingEntry .1.3.6.1.4.1.890.1.5.13.5.10.6.6.1 |
elcPortTrunkingSlotro INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.6.6.1.1 |
elcPortTrunkingGroupIdro INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.6.6.1.2 |
elcPortTrunkingStatusro Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.6.6.1.3 |
elcPortTrunkingPortListro PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.10.6.6.1.4 |
stp OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.10.7 |
rstpEnableEnable/disable RSTP protocol.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.7.1 |
bcastCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.10.8 |
bctrlPortTableThe table contains broadcast storm control configuration for the ethernet ports. SEQUENCE OF BctrlPortEntry .1.3.6.1.4.1.890.1.5.13.5.10.8.1 |
bctrlPortEntry BctrlPortEntry .1.3.6.1.4.1.890.1.5.13.5.10.8.1.1 |
bctrlPortBcastEnableEnable/disable storm control for broadcast packets.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.8.1.1.1 |
bctrlPortMcastEnableEnable/disable storm control for multicast packets.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.8.1.1.2 |
bctrlPortUcastEnableEnable/disable storm control for unicast packets.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.8.1.1.3 |
bctrlPortBcastThreshThe threshold of broadcast storm control.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.8.1.1.4 |
bctrlPortMcastThreshThe threshold of multicast storm control.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.8.1.1.5 |
bctrlPortUcastThreshThe threshold of unicast storm control.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.8.1.1.6 |
portIsolation OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.10.9 |
portIsolationEnableEnable/disable port isolation.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.9.1 |
dscp OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.10.10 |
dscpMappingPortTableThe table contains DSCP mapping configuration for the ethernet ports.
This table is supported by R1.02 and later versions. SEQUENCE OF DscpMappingPortEntry .1.3.6.1.4.1.890.1.5.13.5.10.10.1 |
dscpMappingPortEntryAn entry of dscpMappingPortTable. DscpMappingPortEntry .1.3.6.1.4.1.890.1.5.13.5.10.10.1.1 |
dscpMappingPortSrcCodePointThe DSCP source code point used for mapping.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.10.1.1.1 |
dscpMappingPortMapCodePointThe mapping code point that will replace the source code point in the incoming packet.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.10.1.1.2 |
dscpMappingPortMapPriorityThe mapping p bits that will replace the source p bits in the incoming packet.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.10.1.1.3 |
mstp OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.10.11 |
mstpEnableEnable/disable MSTP protocol. This object is supported by R1.02 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.11.1 |
mstpProtocolVersionThe MSTP protocol version. This object is supported by R1.02 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.11.2 |
mstpBridgeMaxAgeThe value that all bridges use for MaxAge when this bridge is acting as the root.
This object is supported by R1.02 and later versions.rw Timeout .1.3.6.1.4.1.890.1.5.13.5.10.11.3 |
mstpBridgeHelloTimeThe value that all bridges use for HelloTime when this bridge is acting as the root.
This object is supported by R1.02 and later versions.rw Timeout .1.3.6.1.4.1.890.1.5.13.5.10.11.4 |
mstpBridgeForwardDelayThe value that all bridges use for ForwardDelay when this bridge is acting as the root.
This object is supported by R1.02 and later versions.rw Timeout .1.3.6.1.4.1.890.1.5.13.5.10.11.5 |
mstpMaxHopsThe maximum hops that is allowed. This object is supported by R1.02 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.11.6 |
mstpCfgNameThe configuration name that identifies the MST region and is used as
one of the inputs in the computation of the MST Configuration Identifier.
This object is supported by R1.02 and later versions.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.10.11.7 |
mstpCfgRevLevelThis object identifies the MST revision that identifies the MST region and
is used as one of the inputs in the computation of the MST configuration Identifier.
This object is supported by R1.02 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.11.8 |
mstpCfgDigestConfiguration Digest. This object is supported by R1.02 and later versions.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.10.11.9 |
mstpMapTableThis table contains one entry for each instance of MSTP.
This table is supported by R1.02 and later versions. SEQUENCE OF MstpMapEntry .1.3.6.1.4.1.890.1.5.13.5.10.11.10 |
mstpMapEntryA conceptual row containing the status of the MSTP instance. MstpMapEntry .1.3.6.1.4.1.890.1.5.13.5.10.11.10.1 |
mstpMapIndexUniquely identifies an instance.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.11.10.1.1 |
mstpMapVlans1kA string of octets containing one bit per VLAN for VLANS with VlanIndex values
0 through 1023. The first octet corresponds to VLANs with VlanIndex values
0 through 7; the second octet to VLANs 8 through 15 etc. The most significant bit
of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN
that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'.rw OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.10.11.10.1.2 |
mstpMapVlans2kA string of octets containing one bit per VLAN for VLANS with VlanIndex values
1024 through 2047. The first octet corresponds to VLANs with VlanIndex values
1024 through 1031; the second octet to VLANs 1032 through 1039 etc. The most significant bit
of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN
that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'.rw OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.10.11.10.1.3 |
mstpMapVlans3kA string of octets containing one bit per VLAN for VLANS with VlanIndex values
2048 through 3071. The first octet corresponds to VLANs with VlanIndex values
2048 through 2055; the second octet to VLANs 2056 through 2063 etc. The most significant bit
of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN
that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'.rw OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.10.11.10.1.4 |
mstpMapVlans4kA string of octets containing one bit per VLAN for VLANS with VlanIndex values
3072 through 4095. The first octet corresponds to VLANs with VlanIndex values
3072 through 3079; the second octet to VLANs 3080 through 3087 etc. The most significant bit
of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN
that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'.rw OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.10.11.10.1.5 |
mstpVlanTableThis table contains one entry for each VlanId.
This table is supported by R1.02 and later versions. SEQUENCE OF MstpVlanEntry .1.3.6.1.4.1.890.1.5.13.5.10.11.11 |
mstpVlanEntryInformation regarding the instance to which each Vlan is mapped. MstpVlanEntry .1.3.6.1.4.1.890.1.5.13.5.10.11.11.1 |
mstpVlanIndexThe VlanId for which this entry contains the instance mapped.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.10.11.11.1.1 |
mstpVlanMstIndexAn integer with values ranging from 0 to 64 that identify a
the CIST/MSTI instance to which this VLAN is mappedro INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.11.11.1.2 |
mstpPortTableA table that contains port-specific MSTP information.
This table is supported by R1.02 and later versions. SEQUENCE OF MstpPortEntry .1.3.6.1.4.1.890.1.5.13.5.10.11.12 |
mstpPortEntryA list of MSTP information maintained by each port. MstpPortEntry .1.3.6.1.4.1.890.1.5.13.5.10.11.12.1 |
mstpPortAdminEdgePortThe administrative value of the Edge Port parameter. A value of true(1)
indicates that this port should be assumed as an edge-port and a value of
false(2) indicates that this port should be assumed as a non-edge-port.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.11.12.1.1 |
mstpPortAdminPointToPointThe administrative point-to-point status of the LAN segment
attached to this port. A value of forceTrue(0) indicates
that this port should always be treated as if it is connected
to a point-to-point link. A value of forceFalse(1) indicates
that this port should be treated as having a shared media
connection. A value of auto(2) indicates that this port is
considered to have a point-to-point link if it is an Aggregator
and all of its members are aggregatable, or if the MAC entity
is configured for full duplex operation, either through
auto-negotiation or by management means.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.11.12.1.2 |
mstpXstTableBridge priority configuration for multiple spanning trees.
This table is supported by R1.02 and later versions. SEQUENCE OF MstpXstEntry .1.3.6.1.4.1.890.1.5.13.5.10.11.13 |
mstpXstEntryAn entry of mstpXstTable. MstpXstEntry .1.3.6.1.4.1.890.1.5.13.5.10.11.13.1 |
mstpXstIdIdentifies a spanning tree.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.11.13.1.1 |
mstpXstBridgePriorityBridge priority, in steps of 4096.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.11.13.1.2 |
mstpXstPortTablePort configuration for multiple spanning trees.
This table is supported by R1.02 and later versions. SEQUENCE OF MstpXstPortEntry .1.3.6.1.4.1.890.1.5.13.5.10.11.14 |
mstpXstPortEntryAn entry of mstpXstPortTable. MstpXstPortEntry .1.3.6.1.4.1.890.1.5.13.5.10.11.14.1 |
mstpXstPortXstIdIdentifies a spanning tree.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.11.14.1.1 |
mstpXstPortIndexThe port number of the port for which this entry contains MSTP management information.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.11.14.1.2 |
mstpXstPortEnableThe enabled/disabled status of the port.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.11.14.1.3 |
mstpXstPortPriorityThe value of the priority field which is contained in the first
(in network byte order) octet of the (2 octet long) Port ID.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.11.14.1.4 |
mstpXstPortAdminPathCostThe contribution of this port to the path cost of paths towards the spanning tree
root which include this port. 0 menas it is determined by link speed.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.11.14.1.5 |
vlanIsolation OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.10.12 |
vlanIsolationTableA table contains configuration of isolated VLAN.
This table is supported by R3.00 and later versions. SEQUENCE OF VlanIsolationEntry .1.3.6.1.4.1.890.1.5.13.5.10.12.1 |
vlanIsolationEntryAn entry of vlanIsolationTable. VlanIsolationEntry .1.3.6.1.4.1.890.1.5.13.5.10.12.1.1 |
vlanIsolationRowStatusRow status of the table used to create/delete an entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.10.12.1.1.1 |
mac OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.10.13 |
macAgingTimeThe mac aging time in seconds.rw INTEGER UNITS "seconds" .1.3.6.1.4.1.890.1.5.13.5.10.13.1 |
cfm OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.10.14 |
cfmLoopbackPortTableA table that contains CFM information.
This table is supported by R5.02 and later versions. SEQUENCE OF CfmLoopbackPortEntry .1.3.6.1.4.1.890.1.5.13.5.10.14.1 |
cfmLoopbackPortEntryAn entry in cfmLoopbackPortTable. CfmLoopbackPortEntry .1.3.6.1.4.1.890.1.5.13.5.10.14.1.1 |
cfmLoopbackPortStateCFM loopback enable/disable on the port.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.14.1.1.1 |
cfmMIPTable SEQUENCE OF CfmMIPEntry .1.3.6.1.4.1.890.1.5.13.5.10.14.2 |
cfmMIPEntryAn entry in cfmMIPTable. CfmMIPEntry .1.3.6.1.4.1.890.1.5.13.5.10.14.2.1 |
cfmLevelro INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.14.2.1.1 |
cfmVlanIDro INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.14.2.1.2 |
cfmPortro INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.14.2.1.3 |
cfmMIPRowStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.10.14.2.1.4 |
cfmMIPMacAddressMAC address of maintenance domain intermediate pointrw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.10.14.2.1.5 |
cfmActionEnableStatusCFM Action enable status for the CO devicerw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.14.3 |
cfmModeThe compliant CFM standardrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.14.4 |
cfmMIPRespondMcastLbmThe status indicate whether a MIP respond to mulcast lbms or not.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.14.5 |
cfmLoopbackTimeoutCFM loopback timeout value.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.14.6 |
cfmLbrTableThis table contains a list of Loopback replies received by a specific MEP in response to a loopback message. SEQUENCE OF CfmLbrEntry .1.3.6.1.4.1.890.1.5.13.5.10.14.7 |
cfmLbrEntryThe Loopback Reply table entry. CfmLbrEntry .1.3.6.1.4.1.890.1.5.13.5.10.14.7.1 |
cfmLbrSeqNumberTransaction identifier/Sequence number returned by
a previous transmit loopback message command, indicating
which LBM's response is going to be returned. Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.10.14.7.1.1 |
cfmLbrReceiveOrderAn index to distinguish among multiple LBRs with the same
LBR Transaction Identifier field value. cfmLbrReceiveOrder
are assigned sequentially from 1, in the order that the
Loopback Initiator received the LBRs. Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.10.14.7.1.2 |
cfmLbrSrcMacSource MAC address returned in the LBR.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.10.14.7.1.3 |
oam OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.10.15 |
remoteLoopbackTableA table that contains OAM information.
This table is supported by R5.02 and later versions. SEQUENCE OF RemoteLoopbackEntry .1.3.6.1.4.1.890.1.5.13.5.10.15.1 |
remoteLoopbackEntryAn entry in remoteLoopbackTable. RemoteLoopbackEntry .1.3.6.1.4.1.890.1.5.13.5.10.15.1.1 |
remoteLoopbackEnableOAM remote loopback enable/disable on the port.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.15.1.1.1 |
vlanpriority OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.10.16 |
vlanpriorityEnablerw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.16.1 |
vlanpriorityTableA table that contains VLAN Priority information.
This table is supported by R5.04 and later versions. SEQUENCE OF VlanpriorityEntry .1.3.6.1.4.1.890.1.5.13.5.10.16.2 |
vlanpriorityEntryAn entry in vlanpriorityTable. VlanpriorityEntry .1.3.6.1.4.1.890.1.5.13.5.10.16.2.1 |
vlanpriorityVidrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.16.2.1.1 |
vlanpriorityPrirw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.16.2.1.2 |
vlanpriorityRowStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.10.16.2.1.3 |
mirror OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.10.17 |
mirrorEnableset to 'enable' to enable mirroringrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.17.1 |
mirrorMonitorPortmonitor portrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.10.17.2 |
mirrorPortTableThis table is supported by R5.06 and later versions. SEQUENCE OF MirrorPortEntry .1.3.6.1.4.1.890.1.5.13.5.10.17.3 |
mirrorPortEntryAn entry in mirrorPortTable. MirrorPortEntry .1.3.6.1.4.1.890.1.5.13.5.10.17.3.1 |
mirrorPortDirectionSet to 'ingress' to mirror ingress traffic,
'egress' to mirror egress traffic,
'both' to mirror bi-directional traffic,
'none' to disable mirroring in this portrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.17.3.1.1 |
lldp OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.10.18 |
lldpEnableset to 'enable' to enable lldprw Enumeration .1.3.6.1.4.1.890.1.5.13.5.10.18.1 |
sys OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11 |
sysState OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11.1 |
systemStatusThis variable indicates the alarm status of the module.
It is a bit map represented a sum, therefore, it can represent
multiple defects simultaneously. The moduleNoDefect should be set
if and only if no other flag is set.
The various bit positions are:
1 moduleNoDefect
2 moduleOverHeat
3 moduleFanRpmLow
4 moduleVoltageLow
5 moduleThermalSensorFailure
6 modulePullOut
7 powerDC48VAFailure
8 powerDC48VBFailure
9 extAlarmInputTrigger
10 moduleDown
11 mscSwitchOverOK
12 networkTopologyChange
13 macSpoof
14 cpuHigh
15 memoryUsageHigh
16 packetBufferUsageHigh
17 loopguardOccurencero INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.1.1 |
ledStatus OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11.1.2 |
ledAlarmStatusro Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.1.2.1 |
chassisStats OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11.1.3 |
dcPowerStatusThis variable indicates the status of DC Power Status.
The dcPowerStatus is a bit map represented
as a sum, therefore, it can represent multiple defects
simultaneously.
The various bit positions are:
BIT0: POWER Input A
BIT1: POWER Input Bro INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.1.3.1 |
extAlarmStatusThis variable indicates the status of the external alarm.
Every bit record one kind of external alarm, and there are totally 4 kind of them.
Every bit of the variable will be 0 or 1 only, indicate the alarm is clear or set now.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.1.4 |
sysOperation OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11.2 |
sysTargetIfIndex of the operation target.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.2.1 |
sysOpsThe manager sets the corresponding bit value to 1 to start the operation
and the agent clears the object to zero when the operation is successfully completed.
The various bit positions are:
BIT 1: resetrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.2.2 |
sysRebootTimeWrite a non-zero value to schedule a reboot. Write oo0oo to cancel it.
When read, it returns the remaining time to the schedule reboot.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.2.3 |
hwMonitor OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11.3 |
fanRpmTableA table that contains rpm information about the fans. SEQUENCE OF FanRpmEntry .1.3.6.1.4.1.890.1.5.13.5.11.3.1 |
fanRpmEntryA list of rpm information for each fan. FanRpmEntry .1.3.6.1.4.1.890.1.5.13.5.11.3.1.1 |
fanRpmIndexThe identity of the fan.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.3.1.1.1 |
fanRpmCurValueThe current rpm of the fan.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.3.1.1.2 |
fanRpmMaxValueThe maximum rpm ever performed by the fan.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.3.1.1.3 |
fanRpmMinValueThe minimum rpm ever performed by the fan.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.3.1.1.4 |
fanRpmLowThreshThe low threshold of the rpm of the fan.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.3.1.1.5 |
fanRpmDescrThe description of the fan (e.g. location, function, etc.).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.11.3.1.1.6 |
fanRpmHighThreshThe high threshold of the rpm of the fan.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.3.1.1.7 |
voltageTableA table that contains voltage information about the system. SEQUENCE OF VoltageEntry .1.3.6.1.4.1.890.1.5.13.5.11.3.2 |
voltageEntryA list of voltage information for each sensor. VoltageEntry .1.3.6.1.4.1.890.1.5.13.5.11.3.2.1 |
voltageIndexThe identity of the sensor.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.3.2.1.1 |
voltageCurValueThe current voltage detected by the sensor.ro INTEGER UNITS "milli-voltage" .1.3.6.1.4.1.890.1.5.13.5.11.3.2.1.2 |
voltageMaxValueThe maximum voltage ever detected by the sensor.ro INTEGER UNITS "milli-voltage" .1.3.6.1.4.1.890.1.5.13.5.11.3.2.1.3 |
voltageMinValueThe minimum voltage ever detected by the sensor.ro INTEGER UNITS "milli-voltage" .1.3.6.1.4.1.890.1.5.13.5.11.3.2.1.4 |
voltageNominalValueThe nominal voltage which the power should supply.ro INTEGER UNITS "milli-voltage" .1.3.6.1.4.1.890.1.5.13.5.11.3.2.1.5 |
voltageLowThreshThe low threshold of the voltage.rw INTEGER UNITS "milli-voltage" .1.3.6.1.4.1.890.1.5.13.5.11.3.2.1.6 |
voltageDescrThe description of the voltage (e.g. location, nominal value, etc.).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.11.3.2.1.7 |
voltageHighThreshThe high threshold of the voltage.rw INTEGER UNITS "milli-voltage" .1.3.6.1.4.1.890.1.5.13.5.11.3.2.1.8 |
temperatureTableA table that contains temperature information. SEQUENCE OF TemperatureEntry .1.3.6.1.4.1.890.1.5.13.5.11.3.3 |
temperatureEntryA list of temperature information for each sensor. TemperatureEntry .1.3.6.1.4.1.890.1.5.13.5.11.3.3.1 |
temperatureIndexThe identity of the sensor.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.3.3.1.1 |
temperatureCurValueThe current temperature detected by the sensor.ro INTEGER UNITS "Celsius" .1.3.6.1.4.1.890.1.5.13.5.11.3.3.1.2 |
temperatureMaxValueThe maximum temperature ever detected by the sensor.ro INTEGER UNITS "Celsius" .1.3.6.1.4.1.890.1.5.13.5.11.3.3.1.3 |
temperatureMinValueThe minimum temperature ever detected by the sensor.ro INTEGER UNITS "Celsius" .1.3.6.1.4.1.890.1.5.13.5.11.3.3.1.4 |
temperatureHighThreshThe high threshold of the temperature.rw INTEGER UNITS "Celsius" .1.3.6.1.4.1.890.1.5.13.5.11.3.3.1.5 |
temperatureDescrThe description of the temperature sensor (e.g. location, function, etc.).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.11.3.3.1.6 |
temperatureLowThreshThe low threshold of the temperature.rw INTEGER UNITS "Celsius" .1.3.6.1.4.1.890.1.5.13.5.11.3.3.1.7 |
cpuUtilizationTableA table that contains CPU utilization information.
This table is supported by R1.03 and later versions. SEQUENCE OF CpuUtilizationEntry .1.3.6.1.4.1.890.1.5.13.5.11.3.4 |
cpuUtilizationEntryAn entry of cpuUtilizationTable. CpuUtilizationEntry .1.3.6.1.4.1.890.1.5.13.5.11.3.4.1 |
cpuIndexThe identity of the CPU.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.3.4.1.1 |
cpuCurValueThe CPU utilization in the past 60 seconds.ro INTEGER UNITS "Percent" .1.3.6.1.4.1.890.1.5.13.5.11.3.4.1.2 |
cpuMaxValueThe maximum CPU utilization ever detected.ro INTEGER UNITS "Percent" .1.3.6.1.4.1.890.1.5.13.5.11.3.4.1.3 |
cpuHighThreshThe high threshold of CPU usage. If cpuCurValue
is larger than the threshold, the device will initiate the eqptCpuHigh trap.
This trap is supported by R1.03 and later versions.rw INTEGER UNITS "Percent" .1.3.6.1.4.1.890.1.5.13.5.11.3.4.1.4 |
cpuDescrThe description of the CPU. This trap is supported by R1.03 and later versions.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.11.3.4.1.5 |
packetBufferUsageTableA table that contains packet buffer usage information. SEQUENCE OF PacketBufferUsageEntry .1.3.6.1.4.1.890.1.5.13.5.11.3.5 |
packetBufferUsageEntryAn entry of packetBufferUsageTable. PacketBufferUsageEntry .1.3.6.1.4.1.890.1.5.13.5.11.3.5.1 |
packetBufferIndexThe identity of the packet buffer.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.3.5.1.1 |
packetBufferCurValueThe packet buffer usage in the past 60 seconds.ro INTEGER UNITS "Percent" .1.3.6.1.4.1.890.1.5.13.5.11.3.5.1.2 |
packetBufferMaxValueThe maximum packet buffer usage ever detected.ro INTEGER UNITS "Percent" .1.3.6.1.4.1.890.1.5.13.5.11.3.5.1.3 |
packetBufferHighThreshThe high threshold of packet buffer usage. If packetBufferCurValue
is larger than the threshold, the device will initiate the eqptPacketBufferUsageHigh trap.rw INTEGER UNITS "Percent" .1.3.6.1.4.1.890.1.5.13.5.11.3.5.1.4 |
packetBufferDescrThe description of the packet buffer.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.11.3.5.1.5 |
memoryUsageTableA table that contains memory usage information. SEQUENCE OF MemoryUsageEntry .1.3.6.1.4.1.890.1.5.13.5.11.3.6 |
memoryUsageEntryAn entry of memoryUsageTable. MemoryUsageEntry .1.3.6.1.4.1.890.1.5.13.5.11.3.6.1 |
memoryIndexThe identity of the memory.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.3.6.1.1 |
memoryCurValueThe memory usage in the past 60 seconds.ro INTEGER UNITS "Percent" .1.3.6.1.4.1.890.1.5.13.5.11.3.6.1.2 |
memoryMaxValueThe maximum memory usage ever detected.ro INTEGER UNITS "Percent" .1.3.6.1.4.1.890.1.5.13.5.11.3.6.1.3 |
memoryHighThreshThe high threshold of memory usage. If memoryCurValue
is larger than the threshold, the device will initiate the eqptMemoryUsageHigh trap.rw INTEGER UNITS "Percent" .1.3.6.1.4.1.890.1.5.13.5.11.3.6.1.4 |
memoryDescrThe description of the memory.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.11.3.6.1.5 |
timeSetup OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11.4 |
timeServerModeThe mechanism of Time Server when the system boots up.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.4.1 |
timeServerIPThe IP Address of Time Server.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.11.4.2 |
systemTimeThe system time in the format 'HH:MM:SS'.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.11.4.3 |
systemDateThe system date in the format 'YYYY-MM-DD'rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.11.4.4 |
systemTimeZoneThe system time zone.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.4.5 |
timeServerSyncSet the object to 1 to synchronize with the time server.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.4.6 |
dayLightSaving OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11.4.7 |
dayLightSavingAdminStatusrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.4.7.1 |
dayLightSavingStartTime OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11.4.7.2 |
dayLightSavingStartMonthrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.4.7.2.1 |
dayLightSavingStartWeekrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.4.7.2.2 |
dayLightSavingStartWdayrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.4.7.2.3 |
dayLightSavingStartHour1: 01:00,
2: 02:00
3: 03:00
4: 04:00
5: 05:00
6: 06:00
7: 07:00
8: 08:00
9: 09:00
10: 10:00
11: 11:00
12: 12:00
13: 13:00
14: 14:00
15: 15:00
16: 16:00
17: 17:00
18: 18:00
19: 19:00
20: 20:00
21: 21:00
22: 22:00
23: 23:00
24: 00:00rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.4.7.2.4 |
dayLightSavingEndTime OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11.4.7.3 |
dayLightSavingEndMonthrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.4.7.3.1 |
dayLightSavingEndWeekrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.4.7.3.2 |
dayLightSavingEndWdayrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.4.7.3.3 |
dayLightSavingEndHour1: 01:00,
2: 02:00
3: 03:00
4: 04:00
5: 05:00
6: 06:00
7: 07:00
8: 08:00
9: 09:00
10: 10:00
11: 11:00
12: 12:00
13: 13:00
14: 14:00
15: 15:00
16: 16:00
17: 17:00
18: 18:00
19: 19:00
20: 20:00
21: 21:00
22: 22:00
23: 23:00
24: 00:00rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.4.7.3.4 |
timeServerInetAddrTypeThe IP Address type.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.11.4.8 |
timeServerInetAddrThe IP Address of Time Server.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.11.4.9 |
accessCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11.5 |
accessCtrlTableA table that contains information about service access control. SEQUENCE OF AccessCtrlEntry .1.3.6.1.4.1.890.1.5.13.5.11.5.1 |
accessCtrlEntryA list of access control entry. AccessCtrlEntry .1.3.6.1.4.1.890.1.5.13.5.11.5.1.1 |
accessCtrlServiceThe service type of the access control entry.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.5.1.1.1 |
accessCtrlEnableEnable/disable the service.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.5.1.1.2 |
accessCtrlPortThe port number which the service uses.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.5.1.1.3 |
securedClientTableA table that contains information about secured clients. SEQUENCE OF SecuredClientEntry .1.3.6.1.4.1.890.1.5.13.5.11.5.2 |
securedClientEntryA list of secured client entry. SecuredClientEntry .1.3.6.1.4.1.890.1.5.13.5.11.5.2.1 |
securedClientIndexThe index of the entry.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.5.2.1.1 |
securedClientStartIpThe starting IP address of the secured client set.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.11.5.2.1.2 |
securedClientEndIpThe ending IP address of the secured client set.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.11.5.2.1.3 |
securedClientServiceEach bit corresponds to a service. The bit is set to 1 if the
service is enabled, and set to 0 if the service is disabled.
The various bit positions are:
BIT 1: telnet
BIT 2: ftp
BIT 3: web
BIT 4: icmp
BIT 5: ssh
BIT 6: snmp
BIT 7: https.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.5.2.1.4 |
securedClientEnableEnable/disable the entry.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.5.2.1.5 |
securedClientInetTableA table that contains information about secured clients. SEQUENCE OF SecuredClientInetEntry .1.3.6.1.4.1.890.1.5.13.5.11.5.3 |
securedClientInetEntryA list of secured client inet entry. SecuredClientInetEntry .1.3.6.1.4.1.890.1.5.13.5.11.5.3.1 |
securedClientInetIndexThe index of the entry.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.5.3.1.1 |
securedClientInetAddrTyperw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.11.5.3.1.2 |
securedClientInetAddrrw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.11.5.3.1.3 |
securedClientInetMaskrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.5.3.1.4 |
securedClientInetServiceEach bit corresponds to a service. The bit is set to 1 if the
service is enabled, and set to 0 if the service is disabled.
The various bit positions are:
BIT 1: telnet
BIT 2: ftp
BIT 3: web
BIT 4: icmp
BIT 5: ssh
BIT 6: snmp
BIT 7: https.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.5.3.1.5 |
securedClientInetEnableEnable/disable the entry.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.5.3.1.6 |
syslog OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11.6 |
syslogEnableEnable/disable syslog function.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.6.1 |
syslogTableA table that contains syslog configuration. SEQUENCE OF SyslogEntry .1.3.6.1.4.1.890.1.5.13.5.11.6.2 |
syslogEntryA list of syslog entry. SyslogEntry .1.3.6.1.4.1.890.1.5.13.5.11.6.2.1 |
syslogFacilityLog facility.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.6.2.1.1 |
syslogServerIP address of the syslog server.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.11.6.2.1.2 |
syslogServerInetAddrTypeThe IP Address type.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.11.6.2.1.3 |
syslogServerInetAddrIP address of the syslog server.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.11.6.2.1.4 |
snmp OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11.7 |
trapDestTableA table that contains SNMP trap destination information. SEQUENCE OF TrapDestEntry .1.3.6.1.4.1.890.1.5.13.5.11.7.1 |
trapDestEntryThe entry of SNMP trap destination table. TrapDestEntry .1.3.6.1.4.1.890.1.5.13.5.11.7.1.1 |
trapDestIndexThe index of the entry.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.7.1.1.1 |
trapDestIpThe IP address of the trap destination.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.11.7.1.1.2 |
trapDestPortThe UDP port of the trap destination.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.7.1.1.3 |
trapDestSnmpVersionThe SNMP protocol version to send traps.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.7.1.1.4 |
trapDestUserNameThe user name for sending SNMPv3 traps.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.11.7.1.1.5 |
trapDestInetAddrTypeThe IP Address type.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.11.7.1.1.6 |
trapDestInetAddrThe IP address of the trap destination.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.11.7.1.1.7 |
snmpGetCommunityThe SNMP get community.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.11.7.2 |
snmpSetCommunityThe SNMP set community.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.11.7.3 |
snmpTrapCommunityThe SNMP trap community.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.11.7.4 |
snmpUserTableA table that contains SNMPv3 user information. SEQUENCE OF SnmpUserEntry .1.3.6.1.4.1.890.1.5.13.5.11.7.5 |
snmpUserEntryAn entry of snmpUserTable. SnmpUserEntry .1.3.6.1.4.1.890.1.5.13.5.11.7.5.1 |
snmpUserNameThe user name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.11.7.5.1.1 |
snmpUserSecurityLevelThe level of security at which SNMP messages can be sent or
with which operations are being processed.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.7.5.1.2 |
snmpUserAuthProtocolThe type of authentication protocol to be used.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.7.5.1.3 |
snmpUserPrivProtocolThe type of privacy protocol to be used.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.7.5.1.4 |
snmpVersionThe SNMP version to be used. v3v2c means that the manager
can get/set by SNMPv3 and can get by SNMPv2c.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.7.6 |
user OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11.8 |
userTableA table that contains user information. SEQUENCE OF UserEntry .1.3.6.1.4.1.890.1.5.13.5.11.8.5 |
userEntryAn entry of userTable. UserEntry .1.3.6.1.4.1.890.1.5.13.5.11.8.5.1 |
userNameThe user name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.11.8.5.1.1 |
userPasswordThe user password.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.11.8.5.1.2 |
userPriviledgeThe user privilege to decide what operation the user can and cannot do.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.8.5.1.3 |
userRowStatusThe row status used to create or delete a user.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.11.8.5.1.4 |
aaa OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11.9 |
auth OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11.9.1 |
loginMethod1rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.9.1.1 |
loginMethod2rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.9.1.2 |
loginMethod3rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.9.1.3 |
enableMethod1The first method of enable authentication.
This MIB object is supported by R5.06 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.9.1.4 |
enableMethod2The second method of enable authentication.
This MIB object is supported by R5.06 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.9.1.5 |
loginTryContSet to '1' so that the system try next login method only when previous method is not available.
Set to '2' so that the system will try next login method when previous method does not authenticate the user.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.9.1.6 |
acct OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11.9.2 |
systemActiverw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.9.2.1 |
systemMethodrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.9.2.2 |
systemBroadcastrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.9.2.3 |
execActiverw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.9.2.4 |
execMethodrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.9.2.5 |
execModerw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.9.2.6 |
execBroadcastrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.9.2.7 |
commandsActiverw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.9.2.8 |
commandsPrivilege1~14rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.9.2.9 |
commandsBroadcastrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.9.2.10 |
updatePeriod1~2147483647 minutesrw Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.11.9.2.11 |
radius OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11.9.3 |
radiusAuth OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11.9.3.1 |
radiusAuthRedundantModerw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.9.3.1.1 |
radiusAuthTimeoutPeriod1~1000 secondsrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.9.3.1.2 |
radiusAuthServerTable SEQUENCE OF RadiusAuthServerEntry .1.3.6.1.4.1.890.1.5.13.5.11.9.3.1.3 |
radiusAuthServerEntryAn entry of radiusAuthServerTable. RadiusAuthServerEntry .1.3.6.1.4.1.890.1.5.13.5.11.9.3.1.3.1 |
radiusAuthServerIndexro INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.9.3.1.3.1.1 |
radiusAuthServerIPrw IpAddress .1.3.6.1.4.1.890.1.5.13.5.11.9.3.1.3.1.2 |
radiusAuthServerPortrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.9.3.1.3.1.3 |
radiusAuthServerSecretrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.11.9.3.1.3.1.4 |
radiusAcct OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11.9.3.2 |
radiusAcctTimeoutPeriod1~1000 secondsrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.9.3.2.1 |
radiusAcctServerTable SEQUENCE OF RadiusAcctServerEntry .1.3.6.1.4.1.890.1.5.13.5.11.9.3.2.2 |
radiusAcctServerEntryAn entry of radiusAcctServerTable. RadiusAcctServerEntry .1.3.6.1.4.1.890.1.5.13.5.11.9.3.2.2.1 |
radiusAcctServerIndexro INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.9.3.2.2.1.1 |
radiusAcctServerIPrw IpAddress .1.3.6.1.4.1.890.1.5.13.5.11.9.3.2.2.1.2 |
radiusAcctServerPortrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.9.3.2.2.1.3 |
radiusAcctServerSecretrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.11.9.3.2.2.1.4 |
radiusAcctRedundantModeRedundant mode of accounting via RADIUS.
This MIB object is supported by R5.06 and later versionsrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.9.3.2.3 |
tacacsplus OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11.9.4 |
tacacsplusAuth OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11.9.4.1 |
tacacsplusAuthRedundantModerw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.9.4.1.1 |
tacacsplusAuthTimeoutPeriod1~1000 secondsrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.9.4.1.2 |
tacacsplusAuthServerTable SEQUENCE OF TacacsplusAuthServerEntry .1.3.6.1.4.1.890.1.5.13.5.11.9.4.1.3 |
tacacsplusAuthServerEntryAn entry of tacacsplusAuthServerTable. TacacsplusAuthServerEntry .1.3.6.1.4.1.890.1.5.13.5.11.9.4.1.3.1 |
tacscsplusAuthServerIndexro INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.9.4.1.3.1.1 |
tacscsplusAuthServerIPrw IpAddress .1.3.6.1.4.1.890.1.5.13.5.11.9.4.1.3.1.2 |
tacscsplusAuthServerPortrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.9.4.1.3.1.3 |
tacscsplusAuthServerSecretrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.11.9.4.1.3.1.4 |
tacacsplusAcct OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11.9.4.2 |
tacacsplusAcctTimeoutPeriod1~1000 seconds.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.9.4.2.1 |
tacacsplusAcctServerTable SEQUENCE OF TacacsplusAcctServerEntry .1.3.6.1.4.1.890.1.5.13.5.11.9.4.2.2 |
tacacsplusAcctServerEntryAn entry of tacacsplusAcctServerTable. TacacsplusAcctServerEntry .1.3.6.1.4.1.890.1.5.13.5.11.9.4.2.2.1 |
tacacsplusAcctServerIndexro INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.9.4.2.2.1.1 |
tacacsplusAcctServerIPrw IpAddress .1.3.6.1.4.1.890.1.5.13.5.11.9.4.2.2.1.2 |
tacacsplusAcctServerPortrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.9.4.2.2.1.3 |
tacacsplusAcctServerSecretrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.11.9.4.2.2.1.4 |
tacacsplusAcctRedundantModeRedundant mode of accounting via TACACS+.
This MIB object is supported by R5.06 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.9.4.2.3 |
tacacsplusAuthor OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11.9.4.3 |
tacacsplusAuthorRedundantModeRedundant mode of command authorization via TACACS+
This MIB Object is supported by R5.06 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.9.4.3.1 |
tacacsplusAuthorTimeoutPeriodTimeout period (second) of command authorization via TACACS+. 1~1000 seconds
This MIB Object is supported by R5.06 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.9.4.3.2 |
tacacsplusAuthorServerTableThis table is supported by R5.06 and later versions. SEQUENCE OF TacacsplusAuthorServerEntry .1.3.6.1.4.1.890.1.5.13.5.11.9.4.3.3 |
tacacsplusAuthorServerEntryAn entry of tacacsplusAuthorServerEntry.
This table is supported by R5.06 and later versions. TacacsplusAuthorServerEntry .1.3.6.1.4.1.890.1.5.13.5.11.9.4.3.3.1 |
tacscsplusAuthorServerIndexro INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.9.4.3.3.1.1 |
tacscsplusAuthorServerIPTACACS+ server IP for command authorization.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.11.9.4.3.3.1.2 |
tacscsplusAuthorServerPortTACACS+ server port for command authorization.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.9.4.3.3.1.3 |
tacscsplusAuthorServerSecretTACACS+ server secret key for command authorization.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.11.9.4.3.3.1.4 |
author OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11.9.5 |
authorCmdMethodTableThis table is supported by R5.06 and later versions. SEQUENCE OF AuthorCmdMethodEntry .1.3.6.1.4.1.890.1.5.13.5.11.9.5.1 |
authorCmdMethodEntryAn entry of authorCmdMethodEntry. AuthorCmdMethodEntry .1.3.6.1.4.1.890.1.5.13.5.11.9.5.1.1 |
authorCmdMethodMethod mode of command authorization in each privilege level.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.9.5.1.1.1 |
authorExecenable:
1. User login via Web GUI:
1.1. Tacacs+ account with privilege 14, get the privilege as 14.
1.2. Tacacs+ account with privilege lower than 14, get the privilege as 1.
2. User login via SSH, telnet or console:
1.1. Whether Tacacs+ account privilege is (1-14), get the same privilege as Tacacs+ server.
disable:
1. Whether user login via SSH, telnet, web GUI or console, get the privilege as 1.
(no matter what the Tacacs+ account privilege is)rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.9.5.2 |
session OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11.10 |
sessionTimeOutConfigurable Web, telnet and SSH session timeout.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.11.10.1 |
sessionLoginMessageLogin message in 128 characters.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.11.10.2 |
bootimage OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.11.11 |
sysBootImageBoot from the first image or the second image.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.11.11.1 |
trap OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.12 |
object OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.12.1 |
eqpt48VPowerIndexThe index of DC 48V power supply.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.12.1.1 |
eqptAlarmInputIndexThe index of alarm input.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.12.1.2 |
eqptDslDeviceIndexThe index of DSL device.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.12.1.3 |
eqptShdslSubDeviceIndexThe sub-device index of SHDSL device.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.12.1.4 |
sysUserThe user capable of administering this NE with different priority level.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.12.1.5 |
sysAccessPointThe access point to this NE.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.12.1.6 |
sysAccessPointIndexThe access point index to this NE.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.12.1.7 |
sysUserLoginIpThe IP address from which the user login.ro IpAddress .1.3.6.1.4.1.890.1.5.13.5.12.1.8 |
eqptLTResetSourceThe source that triggers LT reset.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.12.1.9 |
sysProfSyncIpAddressThe server IP address to be synchronized or the client IP address to synchronize.ro IpAddress .1.3.6.1.4.1.890.1.5.13.5.12.1.10 |
sysMacAntiSpoofOrigThe original port of Mac-AntiSpoofing.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.12.1.11 |
sysMacAntiSpoofNewThe new port of Mac-AntiSpoofing.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.12.1.12 |
sysMacAntiSpoofMacThe mac address of Mac-AntiSpoofing.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.12.1.13 |
intfCfmCcmErrorCausero Enumeration .1.3.6.1.4.1.890.1.5.13.5.12.1.14 |
e1AlarmStatusro Enumeration .1.3.6.1.4.1.890.1.5.13.5.12.1.15 |
e1AlarmCurrentValuero INTEGER .1.3.6.1.4.1.890.1.5.13.5.12.1.16 |
e1AlarmThresholdro INTEGER .1.3.6.1.4.1.890.1.5.13.5.12.1.17 |
dslMacAntiSpoofOrigThe original port of xDSL Mac-AntiSpoofing.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.12.1.18 |
dslMacAntiSpoofMacThe mac address of xDSL Mac-AntiSpoofing.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.12.1.19 |
vopTermPhoneStatePhone Statusro Enumeration .1.3.6.1.4.1.890.1.5.13.5.12.1.20 |
vopRingTimerSegmentRing Timer Segment IDro INTEGER .1.3.6.1.4.1.890.1.5.13.5.12.1.21 |
vopRingTimerIdRing Timer IDro INTEGER .1.3.6.1.4.1.890.1.5.13.5.12.1.22 |
vopDscCodecTypeCodec Typero Enumeration .1.3.6.1.4.1.890.1.5.13.5.12.1.23 |
vopMcMediaIdMedia Card IDro INTEGER .1.3.6.1.4.1.890.1.5.13.5.12.1.24 |
vopMcPortport numberro INTEGER .1.3.6.1.4.1.890.1.5.13.5.12.1.25 |
vopDropCallTypero Enumeration .1.3.6.1.4.1.890.1.5.13.5.12.1.26 |
sysUserLoginInetAddrTypero InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.12.1.27 |
sysUserLoginInetAddrro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.12.1.28 |
vopDeviceIdro INTEGER .1.3.6.1.4.1.890.1.5.13.5.12.1.29 |
vopBatteryNumro INTEGER .1.3.6.1.4.1.890.1.5.13.5.12.1.30 |
vopRingerShortCountro INTEGER .1.3.6.1.4.1.890.1.5.13.5.12.1.31 |
vopMgcIPThe IP address of Mgc.ro IpAddress .1.3.6.1.4.1.890.1.5.13.5.12.1.32 |
eqptSptMstiInstanceIdspanning tree msti instance number.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.12.1.33 |
eqptSptPortStateOrigThe original port state of spanning tree .ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.12.1.34 |
eqptSptPortStateNewThe new port state of spanning tree.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.12.1.35 |
eqptSptPortRoleOrigThe original port role of spanning tree.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.12.1.36 |
eqptSptPortRoleNewThe new port role of spanning tree.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.12.1.37 |
dsl OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.12.2 |
dslLineEnableThe line is enabled by administrator. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.2.1 |
dslLineDisableThe line is disabled by administrator. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.2.2 |
dslLineBelowPlannedRateThe payload rate is below planned rate. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.2.3 |
dslLineLdmStartThe line enters loop diagnosis mode. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.2.4 |
dslLineLdmDoneThe line exits loop diagnosis mode. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.2.5 |
dslLinePowerDownL2The line enters power down L2 mode. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.2.6 |
dslLinePowerDownL0The line enters power down L0 mode. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.2.7 |
dslLineFailureThe line is failed. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.2.8 |
dslLineEnterTestThe line enters testing mode. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.2.9 |
dslLineExitTestThe line exits testing mode. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.2.10 |
dslLineVdslRateChangeThis notification indicates VDSL link rate change. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.2.12 |
dslLoopGuardLoop guard is traggered. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.2.13 |
dslMacAntiSpoofxDsl MAC spoofing is traggered. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.2.14 |
dslLineVturInfoReadyThe vtur info is ready. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.2.15 |
dslLineVturLprCPE is down. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.2.16 |
equipment OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.12.3 |
eqpt48VPowerFailureThe power supply of DC 48V is failed. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.1 |
eqpt48VPowerNormalThe power supply of DC 48V is normal. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.2 |
eqptVoltageErrorThe voltage is abnormal. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.3 |
eqptVoltageNormalThe voltage is normal. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.4 |
eqptTempErrorThe temperature is abnormal. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.5 |
eqptTempNormalThe temperature is normal. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.6 |
eqptFanErrorThe fan RPM is abnormal. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.7 |
eqptFanNormalThe fan RPM is normal. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.8 |
eqptTempLowFanStopThe fan is stopped due to low temperature. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.9 |
eqptHWMonitorFailureHardware monitor diagnosis is failed. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.10 |
eqptExternalAlarmInputExternal alarm input. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.11 |
eqptTopologyChangeThe change of spanning tree topology is detected. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.12 |
eqptFWUploadOKUploading firmware is completed. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.13 |
eqptFWUploadFailureUploading firmware is failed. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.14 |
eqptLTPlugInLT is plugged in. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.15 |
eqptLTPullOutLT is pulled out. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.16 |
eqptLTActiveLT is active. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.17 |
eqptLTInactiveLT is inactive. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.18 |
eqptLTFWUploadOKUploading firmware to LT is completed. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.19 |
eqptLTFWUploadFailureUploading firmware to LT is failed. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.20 |
eqptLTDslDeviceFailureLT DSL device is failed. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.21 |
eqptLTDslDeviceRedownloadThe firmware of LT DSL device is re-downloaded. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.22 |
eqptLTShdslDeviceRedownloadThe firmware of LT DSL device is re-downloaded. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.23 |
eqptLTEnableLT is enabled. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.24 |
eqptLTDisableLT is disabled. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.25 |
eqptLTResetLT is reset. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.26 |
eqptExternalAlarmInputReleaseExternal alarm input is released. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.27 |
eqptNTSwitchOKThe trap signifies that MSC card is switched over successfully. The value of
slotId is the slot ID of the current working MSC. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.28 |
eqptCpuUtilizationHighThe CPU utilization is over its high threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.29 |
eqptCpuUtilizationNormalThe CPU utilization is normal. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.30 |
eqptPacketBufferUsageHighThe packet buffer usage is over its high threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.31 |
eqptPacketBufferUsageNormalThe packet buffer usage is normal. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.32 |
eqptMemoryUsageHighThe memory usage is over its high threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.33 |
eqptMemoryUsageNormalThe memory usage is normal. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.34 |
eqptDbInactiveThe control card daughter board is inactive. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.35 |
eqptDbNormalThe control card daughter board is normal. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.36 |
eqptDbResetThe control card daughter board is reset. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.37 |
eqptSptPortStateChangeThe spanning tree msti port state change. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.38 |
eqptSptPortRoleChangeThe spanning tree msti port role change. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.3.39 |
systrap OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.12.4 |
sysRebootSystem reboot. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.4.1 |
sysConfigChangeSystem configuration is changed. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.4.2 |
sysConfigUploadOKUploading system configuration is completed. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.4.3 |
sysConfigUploadFailureUploading system configuration is failed. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.4.4 |
sysTimeSyncFailureSynchronizing time with the time server is failed. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.4.5 |
sysAlarmCutoffEnableAlarm cutoff is activated. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.4.6 |
sysAlarmClearEnableAlarm clear is activated. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.4.7 |
sysLoginFailureUser login is failed. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.4.8 |
sysLoginUser logins. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.4.9 |
sysUserAddedUser added. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.4.10 |
sysUserDeletedUser deleted. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.4.11 |
sysUserModifiedUser modified. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.4.12 |
sysSvrSyncProfOKServer synchronize profiles successfully. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.4.13 |
sysSvrSyncProfFailServer failed to synchronize profiles to a client. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.4.14 |
sysCliSyncProfOKClient synchronize profiles from server successfully. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.4.15 |
sysCliSyncProfFailClient failed to synchronize profiles from server. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.4.16 |
sysMacAntiSpoofingMAC Anti-spoofing. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.4.17 |
sysClusterMemberAddCluster member is added. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.4.18 |
sysClusterMemberDeleteCluster member is deleted. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.4.19 |
sysClusterMemberActiveCluster member is active. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.4.20 |
sysClusterMemberInactiveCluster member is inactive. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.4.21 |
sysLoginInetUser logins. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.4.22 |
sysLoginFailureInetUser login is failed. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.4.23 |
enet OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.12.5 |
enetEnableGigabit Ethernet interface is enabled. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.5.1 |
enetDisableGigabit Ethernet interface is disabled. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.5.2 |
enetLoopGuardLoop guard is traggered. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.5.3 |
enetSfpErrorSFP DDMI parameters out of range. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.5.4 |
enetSfpNormalSFP DDMI parameters back to range. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.5.5 |
enetSfpTxEnableSFP TX power is enabled. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.5.6 |
enetSfpTxDisableSFP TX power is disabled. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.5.7 |
interface OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.12.6 |
cfmCcmError NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.6.1 |
tdm OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.12.7 |
e1AlarmLinkLOS NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.7.1 |
e1AlarmPathLOF NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.7.2 |
e1AlarmPathAIS NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.7.3 |
e1AlarmPathRDI NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.7.4 |
e1AlarmPathOCASMF NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.7.5 |
e1AlarmPathOCRCMF NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.7.6 |
e1AlarmLinkSF NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.7.7 |
e1AlarmLinkSD NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.7.8 |
e1AlarmTCAQuarterES NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.7.9 |
e1AlarmTCAQuarterSES NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.7.10 |
e1AlarmTCAQuarterUAS NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.7.11 |
e1AlarmTCADayES NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.7.12 |
e1AlarmTCADaySES NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.7.13 |
e1AlarmTCADayUAS NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.7.14 |
voiptrap OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.12.8 |
vopTempErrortemperature out of low or high threshold NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.1 |
vopTempNormaltemperature normal NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.2 |
vopDCFailDC power feed got problem NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.3 |
vopDCNormalDC power feed normal NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.4 |
vopACFailAC power feed got problem NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.5 |
vopACNormalAC power feed normal NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.6 |
vopRingTimerRinger timer got problem NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.7 |
vopRingResourceRinger electrical load exceed REN (Ring Equivalent number) NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.8 |
vopRingOverHeadHigh load indication of RI (Ring Indicator, control signal from modem to computer, indicate phone line is ringing) NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.9 |
vopNoFreeDSPChannelDSP resource is not enough for voice processing NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.10 |
vopMCMissingSignal Card detects Media Card missing NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.11 |
vopSCMissingMedia Card detects Signaling Card missing NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.12 |
vopTermNameDupDuplicate termination name used NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.13 |
vopNoProtectionCan not find protection card on specified slot NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.14 |
vopProtectionSwitchSignal Card protection switch happened NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.15 |
vopDropCallPhone call exceed short / long term limit NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.16 |
vopBatteryFailCODEC/SLIC module report Battery power failed NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.17 |
vopBatteryNormalCODEC/SLIC module report Battery power normal NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.18 |
vopClockFailVCP chip CLOCK failed or missing NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.19 |
vopClockNormalVCP chip CLOCK normal NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.20 |
vopRingerFailCODEC/SLIC module external ringer does not work NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.21 |
vopRingerNormalCODEC/SLIC module external ringer work normal NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.22 |
vopMgcMissingIndicate the state of mgc. Missing trap will be issue when mg had registered to mgc,
and disconnected happened. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.23 |
vopMgcNormalIndicate the state of mgc. Normal trap will be issue when missing trap is not clear
and mg registered to mgc again. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.24 |
vopMgEnableIndicate the state of mg. Mg enable trap will be issued when user enable the mg in manual. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.25 |
vopMgDisableIndicate the state of mg. Mg disable trap will be issued when user disable the mg in manual. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.26 |
vopPortMissingnone. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.27 |
vopPortNormalnone. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.28 |
vopMcNormalMC is normal. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.29 |
vopScNormalSC is normal. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.30 |
vopScBulkSyncReadySC bulk sync completed. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.31 |
vopProtectionReadySC redundancy is ready. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.13.5.12.8.32 |
statistics OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13 |
dhcpStats OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.1 |
dhcpSnoopIpTableThis table shows the IP addresses and netmasks offered by the DHCP server.
This table is supported by R1.02 and later versions. SEQUENCE OF DhcpSnoopIpEntry .1.3.6.1.4.1.890.1.5.13.5.13.1.1 |
dhcpSnoopIpEntryAn entry of dhcpSnoopIpTable. DhcpSnoopIpEntry .1.3.6.1.4.1.890.1.5.13.5.13.1.1.1 |
dhcpSnoopIpThe snooped IP address.ro IpAddress .1.3.6.1.4.1.890.1.5.13.5.13.1.1.1.1 |
dhcpSnoopMacThe snooped MAC address.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.1.1.1.2 |
dhcpSnoopVidThe snooped VLAN ID.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.1.1.1.3 |
dhcpSnoopCounterTableThis table shows the DHCP statistics.
This table is supported by R1.02 and later versions. SEQUENCE OF DhcpSnoopCounterEntry .1.3.6.1.4.1.890.1.5.13.5.13.1.2 |
dhcpSnoopCounterEntryAn entry of dhcpSnoopCounterTable. DhcpSnoopCounterEntry .1.3.6.1.4.1.890.1.5.13.5.13.1.2.1 |
dhcpDiscoveryThe total number of received DHCP server discovery packets.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.1.2.1.1 |
dhcpOfferThe total number of received DHCP server offer packets.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.1.2.1.2 |
dhcpRequestThe total number of received DHCP IP request packets.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.1.2.1.3 |
dhcpAckThe total number of received DHCP IP acknowledge packets.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.1.2.1.4 |
dhcpAckBySnoopFullThe total number of received DHCP IP acknowledge packets that replace the oldest snooping
entry in snooping table due to table full.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.1.2.1.5 |
dhcpv6SolicitThe total number of received DHCPv6 solicit packets.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.1.2.1.6 |
dhcpv6AdvertiseThe total number of received DHCPv6 advertise packets.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.1.2.1.7 |
dhcpv6RequestThe total number of received DHCPv6 request packets.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.1.2.1.8 |
dhcpv6ReplyThe total number of received DHCPv6 reply packets.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.1.2.1.9 |
dhcpv6RenewThe total number of received DHCPv6 renew packets.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.1.2.1.10 |
dhcpv6RebindThe total number of received DHCPv6 rebind packets.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.1.2.1.11 |
dhcpv6ReleaseThe total number of received DHCPv6 release packets.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.1.2.1.12 |
dhcpv6RelayFwdThe total number of received DHCPv6 relay-forward packets.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.1.2.1.13 |
dhcpv6RelayReplyThe total number of received DHCPv6 relay-reply packets.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.1.2.1.14 |
dhcpv6SnoopIpTableThis table shows LDRA statistics. SEQUENCE OF Dhcpv6SnoopIpEntry .1.3.6.1.4.1.890.1.5.13.5.13.1.3 |
dhcpv6SnoopIpEntryAn entry of dhcpv6SnoopIpTable. Dhcpv6SnoopIpEntry .1.3.6.1.4.1.890.1.5.13.5.13.1.3.1 |
dhcpv6SnoopInetAddrTypeThe snooped IP address type.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.1.3.1.1 |
dhcpv6SnoopInetAddrThe snooped IP address.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.1.3.1.2 |
dhcpv6SnoopMacThe snooped MAC address.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.1.3.1.3 |
dhcpv6SnoopVidThe snooped VLAN ID.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.1.3.1.4 |
igmpStats OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.2 |
igmpQueryCntTotalThe total number of IGMP query messages received.
This object is supported by R1.02 and later versions.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.1 |
igmpReportCntTotalThe total number of IGMP report messages received.
This object is supported by R1.02 and later versions.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.2 |
igmpLeaveCntTotalThe total number of IGMP leave messages received.
This object is supported by R1.02 and later versions.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.3 |
igmpNumOfActiveGroupsThe total number of IGMP learned groups.
This object is supported by R1.02 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.2.4 |
igmpGroupTableA table that displays IGMP learned group member information.
This table is supported by R1.02 and later versions. SEQUENCE OF IgmpGroupEntry .1.3.6.1.4.1.890.1.5.13.5.13.2.5 |
igmpGroupEntryAn entry of igmpGroupTable. IgmpGroupEntry .1.3.6.1.4.1.890.1.5.13.5.13.2.5.1 |
igmpGroupVidThe IGMP group VLAN ID.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.2.5.1.1 |
igmpGroupIpThe multicast IP address.ro IpAddress .1.3.6.1.4.1.890.1.5.13.5.13.2.5.1.2 |
igmpGroupNumOfMembersThe number of member ports in the group.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.2.5.1.3 |
igmpGroupMemberPortsThe member port list of the group.ro PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.2.5.1.4 |
igmpGroupPortTableA table that displays IGMP joined groups in this port.
This table is supported by R1.02 and later versions. SEQUENCE OF IgmpGroupPortEntry .1.3.6.1.4.1.890.1.5.13.5.13.2.6 |
igmpGroupPortEntryAn entry of igmpGroupPortTable. IgmpGroupPortEntry .1.3.6.1.4.1.890.1.5.13.5.13.2.6.1 |
igmpGroupPortVidThe IGMP group VLAN ID.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.2.6.1.1 |
igmpGroupPortIpThe multicast IP address.ro IpAddress .1.3.6.1.4.1.890.1.5.13.5.13.2.6.1.2 |
igmpGroupPortSourceIpThe source IP address that joins the IGMP group.ro IpAddress .1.3.6.1.4.1.890.1.5.13.5.13.2.6.1.3 |
igmpPortCtrlPduTableA table that displays IGMP related counter values in this port.
This table is supported by R1.02 and later versions. SEQUENCE OF IgmpPortCtrlPduEntry .1.3.6.1.4.1.890.1.5.13.5.13.2.7 |
igmpPortCtrlPduEntryAn entry of igmpPortCtrlPduTable. IgmpPortCtrlPduEntry .1.3.6.1.4.1.890.1.5.13.5.13.2.7.1 |
igmpPortCtrlPduQueryCntThe total number of IGMP query messages received in this port.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.7.1.1 |
igmpPortCtrlPduReportCntThe total number of IGMP report messages received in this port.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.7.1.2 |
igmpPortCtrlPduLeaveCntThe total number of IGMP leave messages received in this port.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.7.1.3 |
igmpPortNumOfActiveGroupsThe total number of active IGMP groups in this port.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.2.7.1.4 |
igmpPortCtrlPduV2SuccessJoinCntThe total number of IGMP V2 success joins in this port.
This MIB object is supported by R5.05 and later versions.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.7.1.5 |
igmpPortCtrlPduV2UnsuccJoinCntThe total number of IGMP V2 unsuccess joins in this port.
This MIB object is supported by R5.05 and later versions.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.7.1.6 |
igmpPortCtrlPduGenQryCntThe total number of IGMP general queries in this port.
This MIB object is supported by R5.05 and later versions.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.7.1.7 |
igmpPortCtrlPduSpecQryCntThe total number of IGMP specific queries in this port.
This MIB object is supported by R5.05 and later versions.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.7.1.8 |
igmpPortCtrlPduV3SuccessReportCntThe total number of IGMP V3 success joins in this port.
This MIB object is supported by R5.05 and later versions.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.7.1.9 |
igmpPortCtrlPduV3UnsuccReportCntThe total number of IGMP V3 unsuccess joins in this port.
This MIB object is supported by R5.05 and later versions.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.7.1.10 |
igmpPortCtrlPduInvalidCntThe total number of IGMP invalid in this port.
This MIB object is supported by R5.05 and later versions.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.7.1.11 |
igmpVlanStatsTableA table that displays IGMP related counter values per VLAN. SEQUENCE OF IgmpVlanStatsEntry .1.3.6.1.4.1.890.1.5.13.5.13.2.8 |
igmpVlanStatsEntryAn entry of igmpVlanStatsTable. IgmpVlanStatsEntry .1.3.6.1.4.1.890.1.5.13.5.13.2.8.1 |
igmpVlanStatsVlanIndexVLAN ID.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.2.8.1.1 |
igmpVlanStatsQueryCntThe total number of IGMP query messages received in this VLAN.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.8.1.2 |
igmpVlanStatsReportCntThe total number of IGMP report messages received in this VLAN.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.8.1.3 |
igmpVlanStatsLeaveCntThe total number of IGMP leave messages received in this VLAN.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.8.1.4 |
igmpVlanStatsNumOfActiveGroupsThe total number of active IGMP groups in this VLAN.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.2.8.1.5 |
igmpVlanStatsQueryPortThe received Port of IGMP Routerro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.2.8.1.6 |
igmpVlanStatsQuerierIpThe IP address of IGMP Routerro IpAddress .1.3.6.1.4.1.890.1.5.13.5.13.2.8.1.7 |
igmpVlanStatsUnsuccessReportCntTotal number of successful joins from users.
This MIB object is supported by R5.05 and later versions.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.8.1.8 |
igmpVlanStatsSuccessReportCntTotal number of unsuccessful joins from users.
This MIB object is supported by R5.05 and later versions.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.8.1.9 |
igmpVlanStatsGeneralQueryInCntTotal number of general queries sent to users.
This MIB object is supported by R5.05 and later versions.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.8.1.10 |
igmpVlanStatsGeneralQueryOutCntTotal number of general queries received from network.
This MIB object is supported by R5.05 and later versions.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.8.1.11 |
igmpVlanStatsSpecificQueryInCntTotal number of specific queries sent to users.
This MIB object is supported by R5.05 and later versions.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.8.1.12 |
igmpVlanStatsSpecificQueryOutCntTotal number of specific queries received from network.
This MIB object is supported by R5.05 and later versions.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.8.1.13 |
igmpQueryOutCntThe total number of IGMP query messages transmitted.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.9 |
igmpReportOutCntThe total number of IGMP report messages transmitted.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.10 |
igmpLeaveOutCntThe total number of IGMP leave messages transmitted.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.11 |
igmpQueryDropCntThe total number of IGMP query messages dropped.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.12 |
igmpReportDropCntThe total number of IGMP report messages dropped.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.13 |
igmpLeaveDropCntThe total number of IGMP leave messages dropped.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.2.14 |
macStats OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.3 |
macDisplayTargetThis managed object is a filter used for identify the target from which
the MAC addresses are learned in macTable. Ifindex is used to specify a specific
interface of which the MAC addresses are displayed. Some values are reserved for
special purpose, they are:
0: All interfaces
50: All uplink portsrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.3.1 |
macTableA table that contains information about unicast
entries for which the bridge has forwarding and/or
filtering information. This information is used
by the transparent bridging function in
determining how to propagate a received frame. SEQUENCE OF MacEntry .1.3.6.1.4.1.890.1.5.13.5.13.3.2 |
macEntryAn entry of macTable. MacEntry .1.3.6.1.4.1.890.1.5.13.5.13.3.2.1 |
macAddressA unicast MAC address for which the bridge has
forwarding and/or filtering information.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.3.2.1.1 |
macPortThe port from which the mac address has been learned.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.3.2.1.2 |
macStatusThe status of this entry.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.3.2.1.3 |
macFlushSet the object to 1 to flush mac table.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.3.3 |
adslStats OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.4 |
adslLineStatsAtucNumOfSubcarriersPerPortThe number of subcarriers per port for ATU-C.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.4.1 |
adslLineStatsAturNumOfSubcarriersPerPortThe number of subcarriers per port for ATU-R.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.4.2 |
adslLineStatsTableThe table displays ADSL line subcarrier status.
This table is supported by R1.02 and later versions. SEQUENCE OF AdslLineStatsEntry .1.3.6.1.4.1.890.1.5.13.5.13.4.3 |
adslLineStatsEntryAn entry of adslLineStatsTable. AdslLineStatsEntry .1.3.6.1.4.1.890.1.5.13.5.13.4.3.1 |
adslLineStatsAtucHlog1The object provides Hlog for the ATU-C first 256 subcarriers.
Each subcarrier takes two octets to store the value.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.4.3.1.1 |
adslLineStatsAtucHlog2The object provides Hlog for the ATU-C last 256 subcarriers.
Each subcarrier takes two octets to store the value.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.4.3.1.2 |
adslLineStatsAturHlogThe object provides Hlog for the ATU-R subcarriers.
Each subcarrier takes two octets to store the value.
A special value -32768 indicates that no measurement could
be done for the sub-carrier group.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.4.3.1.3 |
adslLineStatsAtucQln1The object provides QLN for the ATU-C first 256 subcarriers.
Each subcarrier takes two octets to store the value.
A special value 0 indicates that no measurement could be done
for the sub-carrier group.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.4.3.1.4 |
adslLineStatsAtucQln2The object provides QLN for the ATU-C last 256 subcarriers.
Each subcarrier takes two octets to store the value.
A special value 0 indicates that no measurement could be done
for the sub-carrier group.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.4.3.1.5 |
adslLineStatsAturQlnThe object provides QLN for the ATU-R subcarriers.
Each subcarrier takes two octets to store the value.
A special value 0 indicates that no measurement could be done
for the sub-carrier group.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.4.3.1.6 |
adslLineStatsAtucTssi1The object provides TSSI for the ATU-C first 256 subcarriers.
Each subcarrier takes two octets to store the value.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.4.3.1.7 |
adslLineStatsAtucTssi2The object provides TSSI for the ATU-C last 256 subcarriers.
Each subcarrier takes two octets to store the value.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.4.3.1.8 |
adslLineStatsAturTssiThe object provides TSSI for the ATU-R subcarriers.
Each subcarrier takes two octets to store the value.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.4.3.1.9 |
adslLineStatsAtucGain1The object provides GAIN for the ATU-C first 256 subcarriers.
Each subcarrier takes two octets to store the value.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.4.3.1.10 |
adslLineStatsAtucGain2The object provides GAIN for the ATU-C last 256 subcarriers.
Each subcarrier takes two octets to store the value.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.4.3.1.11 |
adslLineStatsAturGainThe object provides GAIN for the ATU-R subcarriers.
Each subcarrier takes two octets to store the value.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.4.3.1.12 |
adslLineStatsAtucBits1The object provides BITS for the ATU-C first 256 subcarriers.
Each subcarrier takes two octets to store the value.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.4.3.1.13 |
adslLineStatsAtucBits2The object provides BITS for the ATU-C last 256 subcarriers.
Each subcarrier takes two octets to store the value.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.4.3.1.14 |
adslLineStatsAturBitsThe object provides BITS for the ATU-R subcarriers.
Each subcarrier takes two octets to store the value.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.4.3.1.15 |
adslLinePerfTableThe table displays ADSL line performance. SEQUENCE OF AdslLinePerfEntry .1.3.6.1.4.1.890.1.5.13.5.13.4.4 |
adslLinePerfEntryAn entry of adslLinePerfTable. AdslLinePerfEntry .1.3.6.1.4.1.890.1.5.13.5.13.4.4.1 |
adslLinePerfAtucCrcFastThe total number of CRC errors in fast mode.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.4.4.1.1 |
adslLinePerfAturCrcFastThe total number of CRC errors in fast mode.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.4.4.1.2 |
adslLinePerfAtucFecFastThe total number of FEC errors in fast mode.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.4.4.1.3 |
adslLinePerfAturFecFastThe total number of FEC errors in fast mode.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.4.4.1.4 |
adslLinePerfAtucCrcInterleaveThe total number of CRC errors in interleave mode.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.4.4.1.5 |
adslLinePerfAturCrcInterleaveThe total number of CRC errors in interleave mode.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.4.4.1.6 |
adslLinePerfAtucFecInterleaveThe total number of FEC errors in interleave mode.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.4.4.1.7 |
adslLinePerfAturFecInterleaveThe total number of FEC errors in interleave mode.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.4.4.1.8 |
adslLinePerfAtucEsCount of the number of Errored Seconds since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.4.4.1.9 |
adslLinePerfAturEsCount of the number of Errored Seconds since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.4.4.1.10 |
adslLinePerfAtucSesCount of the number of Severely Errored Seconds since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.4.4.1.11 |
adslLinePerfAturSesCount of the number of Severely Errored Seconds since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.4.4.1.12 |
adslLinePerfAtucUasCount of the number of Unavailable Seconds since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.4.4.1.13 |
adslLinePerfAturUasCount of the number of Unavailable Seconds since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.4.4.1.14 |
adslLinePerfAtucLofsCount of the number of Loss of Framing failures since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.4.4.1.15 |
adslLinePerfAturLofsCount of the number of Loss of Framing failures since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.4.4.1.16 |
adslLinePerfAtucLossCount of the number of Loss of Signal failures since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.4.4.1.17 |
adslLinePerfAturLossCount of the number of Loss of Signal failures since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.4.4.1.18 |
adslLinePerfAtucLprsCount of the number of Loss of Power failures since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.4.4.1.19 |
adslLinePerfAturLprsCount of the number of Loss of Power failures since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.4.4.1.20 |
shdslStats OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.5 |
shdslLinePerfTableThe table displays SHDSL line performance. SEQUENCE OF ShdslLinePerfEntry .1.3.6.1.4.1.890.1.5.13.5.13.5.1 |
shdslLinePerfEntryAn entry of shdslLinePerfTable. ShdslLinePerfEntry .1.3.6.1.4.1.890.1.5.13.5.13.5.1.1 |
shdslLinePerfEsCount of Errored Seconds (ES) on this endpoint since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.5.1.1.1 |
shdslLinePerfSesCount of Severely Errored Seconds (SES) on this endpoint since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.5.1.1.2 |
shdslLinePerfCrcCount of CRC anomalies on this endpoint since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.5.1.1.3 |
shdslLinePerfLoswsCount of Loss of Sync Word (LOSW) Seconds on this endpoint since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.5.1.1.4 |
shdslLinePerfUasCount of Unavailable Seconds (UAS) on this endpoint since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.5.1.1.5 |
shdslLinePerfSegmentAnomaliesCount of Segment Anomalies on this endpoint since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.5.1.1.6 |
shdslLinePerfSegmentDefectCount of Segment Defects on this endpoint since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.5.1.1.7 |
shdslPerfCurrTableThe table displays SHDSL current performance. This table is supported by R5.05 and later versions. SEQUENCE OF ShdslPerfCurrEntry .1.3.6.1.4.1.890.1.5.13.5.13.5.2 |
shdslPerfCurrEntryAn entry of shdslPerfCurrTable. ShdslPerfCurrEntry .1.3.6.1.4.1.890.1.5.13.5.13.5.2.1 |
shdslPerfCurrSturLPRCount of the number of Loss of Power failures since agent reset.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.5.2.1.1 |
ipStats OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.6 |
ipInterfaceTableThe table displays IP interface statistics. SEQUENCE OF IpInterfaceEntry .1.3.6.1.4.1.890.1.5.13.5.13.6.1 |
ipInterfaceEntryAn entry of ipInterfaceTable. IpInterfaceEntry .1.3.6.1.4.1.890.1.5.13.5.13.6.1.1 |
ipInterfaceThe IP inband/outband interface.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.6.1.1.1 |
ipAddressIP address of the interface.ro IpAddress .1.3.6.1.4.1.890.1.5.13.5.13.6.1.1.2 |
ipNetmaskNetmask of the interface.ro IpAddress .1.3.6.1.4.1.890.1.5.13.5.13.6.1.1.3 |
ipBroadcastBroadcast address of the interface.ro IpAddress .1.3.6.1.4.1.890.1.5.13.5.13.6.1.1.4 |
ipMtuThe size of the largest datagram which can be sent/received on the interface,
specified in octets.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.6.1.1.5 |
ipVidManagement VLAN ID of the interface.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.6.1.1.6 |
ipInOctetThe total number of octets received on the interface.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.6.1.1.7 |
ipInUnicastThe number of subnetwork-unicast packets delivered to a higher-layer protocol.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.6.1.1.8 |
ipInMulticastThe number of subnetwork-multicast packets delivered to a higher-layer protocol.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.6.1.1.9 |
ipInDiscardThe number of inbound packets which were chosen to be discarded
even though no errors had been detected to prevent their being deliverable to a
higher-layer protocol.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.6.1.1.10 |
ipInErrorThe number of inbound packets that contained errors preventing them from
being deliverable to a higher-layer protocol.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.6.1.1.11 |
ipInUnknownThe number of packets received via the interface which were discarded
because of an unknown or unsupported protocol.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.6.1.1.12 |
ipOutOctetThe total number of octets transmitted out of the interface.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.6.1.1.13 |
ipOutUnicastThe total number of packets that higher-level protocols requested be
transmitted to a subnetwork-unicast address, including those that
were discarded or not sent.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.6.1.1.14 |
ipOutMulticastThe total number of packets that higher-level protocols requested be
transmitted to a subnetwork-multicast address, including those that
were discarded or not sent.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.6.1.1.15 |
ipOutDiscardThe number of outbound packets which were chosen to be discarded even though
no errors had been detected to prevent their being transmitted.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.6.1.1.16 |
ipOutErrorThe number of outbound packets that could not be transmitted because of errors.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.6.1.1.17 |
mstpStats OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.7 |
mstpExternalRootIdThe bridge identifier of the root of the spanning tree as determined by
the Spanning Tree Protocol as executed by this node. This value is used as
the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
This object is supported by R1.02 and later versions.ro BridgeId (BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.7.1 |
mstpExternalRootCostThe cost of the path to the root as seen from this bridge.
This object is supported by R1.02 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.7.2 |
mstpExternalRootPortIdThe port number of the port which offers the lowest cost path from
this bridge to the root bridge.
This object is supported by R1.02 and later versions.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.7.3 |
mstpExternalRootMaxAgeThe maximum age of Spanning Tree Protocol information learned from
the network on any port before it is discarded, in units of hundredths of
a second. This is the actual value that this bridge is currently using.
This object is supported by R1.02 and later versions.ro Timeout (BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.7.4 |
mstpExternalRootHelloTimeThe amount of time between the transmission of Configuration bridge PDUs
by this node on any port when it is the root of the spanning tree or trying
to become so, in units of hundredths of a second. This is the actual value that
this bridge is currently using.
This object is supported by R1.02 and later versions.ro Timeout (BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.7.5 |
mstpExternalRootForwardDelayThis time value, measured in units of hundredths of a second, controls
how fast a port changes its spanning state when moving towards the Forwarding
state. The value determines how long the port stays in each of the Listening
and Learning states, which precede the Forwarding state. This value is also used,
when a topology change has been detected and is underway, to age all dynamic
entries in the Forwarding Database.
This object is supported by R1.02 and later versions.ro Timeout (BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.7.6 |
mstpPortStatsTableA table that contains port-specific MSTP statistics.
This table is supported by R1.02 and later versions. SEQUENCE OF MstpPortStatsEntry .1.3.6.1.4.1.890.1.5.13.5.13.7.7 |
mstpPortStatsEntryA list of MSTP statistics maintained by each port. MstpPortStatsEntry .1.3.6.1.4.1.890.1.5.13.5.13.7.7.1 |
mstpPortStatsExternalRootIdThe unique Bridge Identifier of the Bridge recorded as the Root
in the Configuration BPDUs transmitted by the Designated Bridge for the
segment to which the port is attached.ro BridgeId (BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.7.7.1.1 |
mstpPortStatsExternalRootCostThe path cost of the Designated Port of the segment connected to this port.
This value is compared to the Root Path Cost field in received bridge PDUs.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.7.7.1.2 |
mstpPortStatsExternalPortCostro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.7.7.1.3 |
mstpPortStatsOperEdgePortThe operational value of the Edge Port parameter.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.7.7.1.4 |
mstpPortStatsOperPoint2PointThe operational point-to-point status of the LAN segment attached to this port.
It indicates whether a port is considered to have a point-to-point connection or not.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.7.7.1.5 |
mstpPortStatsMACOperationalro Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.7.7.1.6 |
mstpPortStatsRecvInternalro Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.7.7.1.7 |
mstpPortStatsRxStpCfgBPDUThe total number of received Configuration BPDUs.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.7.7.1.8 |
mstpPortStatsRxStpTcnBPDUThe total number of received Topology Change Notification (TCN) Messages.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.7.7.1.9 |
mstpPortStatsRxRstpBPDUThe total number of received RST BPDUs.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.7.7.1.10 |
mstpPortStatsRxMstpBPDUThe total number of received MST BPDUs.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.7.7.1.11 |
mstpXstStatsTableA table that contains MSTP statistics for multiple spanning trees.
This table is supported by R1.02 and later versions. SEQUENCE OF MstpXstStatsEntry .1.3.6.1.4.1.890.1.5.13.5.13.7.8 |
mstpXstStatsEntryAn entry of mstpXstStatsTable. MstpXstStatsEntry .1.3.6.1.4.1.890.1.5.13.5.13.7.8.1 |
mstpXstStatsBridgeIdro BridgeId (BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.7.8.1.1 |
mstpXstStatsTimeSinceTopologyChangero TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.890.1.5.13.5.13.7.8.1.2 |
mstpXstStatsTopologyChangesCountro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.7.8.1.3 |
mstpXstStatsInternalRootPortIdro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.7.8.1.4 |
mstpXstStatsInternalRootIdro BridgeId (BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.7.8.1.5 |
mstpXstStatsInternalRootCostro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.7.8.1.6 |
mstpXstPortStatsTableA table that contains MSTP port statistics for multiple spanning trees.
This table is supported by R1.02 and later versions. SEQUENCE OF MstpXstPortStatsEntry .1.3.6.1.4.1.890.1.5.13.5.13.7.9 |
mstpXstPortStatsEntryAn entry of mstpXstPortStatsTable. MstpXstPortStatsEntry .1.3.6.1.4.1.890.1.5.13.5.13.7.9.1 |
mstpXstPortStatsUptimero TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.890.1.5.13.5.13.7.9.1.1 |
mstpXstPortStatsPortIdro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.7.9.1.2 |
mstpXstPortStatsStateThe port's current state.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.7.9.1.3 |
mstpXstPortStatsDesignatedBridgeIdThe Bridge Identifier of the bridge which this port considers to be
the Designated Bridge for this port's segment.ro BridgeId (BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.7.9.1.4 |
mstpXstPortStatsDesignatedPortIdThe Port Identifier of the port on the Designated Bridge for this port's segment.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.7.9.1.5 |
mstpXstPortStatsInternalPortCostThe path cost of the Designated Port of the segment connected to this port.
This value is compared to the Root Path Cost field in received bridge PDUs.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.7.9.1.6 |
mstpXstPortStatsInternalRootIdro BridgeId (BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.7.9.1.7 |
vdslStats OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.8 |
vdslLinePerfTableThe table displays VDSL line performance. This table is supported by R2.00 and later versions. SEQUENCE OF VdslLinePerfEntry .1.3.6.1.4.1.890.1.5.13.5.13.8.1 |
vdslLinePerfEntryAn entry of vdslLinePerfTable. VdslLinePerfEntry .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1 |
vdslLinePerfVtucCrcThe number of CRC errors since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.1 |
vdslLinePerfVturCrcThe number of CRC errors since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.2 |
vdslLinePerfVtucFecThe number of FEC errors since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.3 |
vdslLinePerfVturFecThe number of FEC errors since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.4 |
vdslLinePerfVtucLofsCount of the number of Loss of Framing failures since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.5 |
vdslLinePerfVturLofsCount of the number of Loss of Framing failures since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.6 |
vdslLinePerfVtucLossCount of the number of Loss of Signal failures since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.7 |
vdslLinePerfVturLossCount of the number of Loss of Signal failures since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.8 |
vdslLinePerfVtucLprsCount of the number of Loss of Power failures since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.9 |
vdslLinePerfVturLprsCount of the number of Loss of Power failures since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.10 |
vdslLinePerfVtucLolsCount of the number of Loss of Link failures since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.11 |
vdslLinePerfVturLolsCount of the number of Loss of Link failures since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.12 |
vdslLinePerfVtucESsCount of the number of Errored Seconds since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.13 |
vdslLinePerfVturESsCount of the number of Errored Seconds since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.14 |
vdslLinePerfVtucSESsCount of the number of Severely Errored Seconds since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.15 |
vdslLinePerfVturSESsCount of the number of Severely Errored Seconds since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.16 |
vdslLinePerfVtucUASsCount of the number of Unavailable Seconds since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.17 |
vdslLinePerfVturUASsCount of the number of Unavailable Seconds since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.18 |
vdslLinePerfInmVtucEqInpThe INM Equivalent Inp histogram since last link up. An array of 68 octets
(each 4 octets means amount of a bin of histogram), designed for supporting
from 1 to 17 bins of the histogram. The particular index of the bin incremented
by an impulse noise event is equal to the computed value of equivalent INP,
except the 17th of anomaly INPEQ, which logs all equivalent INPs greater than 16.
Each bin has a value in the range 0x0 to 0xFFFFFFFFro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.19 |
vdslLinePerfInmVturEqInpThe INM Equivalent Inp histogram since last link up. An array of 68 octets
(each 4 octets means amount of a bin of histogram), designed for supporting
from 1 to 17 bins of the histogram. The particular index of the bin incremented
by an impulse noise event is equal to the computed value of equivalent INP,
except the 17th of anomaly INPEQ, which logs all equivalent INPs greater than 16.
Each bin has a value in the range 0x0 to 0xFFFFFFFFro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.20 |
vdslLinePerfInmVtucIATThe INM Inter Arrival Time histogram since last link up. An array of 32 octets
(each 4 octets means amount of a bin of histogram), designed for supporting
from 0 to 7 bins of the histogram. The index of the particular bin incremented
by an complete impulse noise event is determained from the following INMControl parameters.
Each bin has a value in the range 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.21 |
vdslLinePerfInmVturIATThe INM Inter Arrival Time histogram since last link up. An array of 32 octets
(each 4 octets means amount of a bin of histogram), designed for supporting
from 0 to 7 bins of the histogram. The index of the particular bin incremented
by an complete impulse noise event is determained from the following INMControl parameters.
Each bin has a value in the range 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.22 |
vdslLinePerfInmVtucMEThe INM total measurement since last link up. This indication occurs every time a data symbol
is processed by the Impulse Noise Sensor. The range of the value is from 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.23 |
vdslLinePerfInmVturMEThe INM total measurement since last link up. This indication occurs every time a data symbol
is processed by the Impulse Noise Sensor. The range of the value is from 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.24 |
vdslLinePerfVtucRxNumber of codewords retransmitted since last link up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.25 |
vdslLinePerfVturRxNumber of codewords retransmitted since last link up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.26 |
vdslLinePerfVtucRxCorrectedNumber of codewords corrected through retransmission since last link up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.27 |
vdslLinePerfVturRxCorrectedNumber of codewords corrected through retransmission since last link up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.28 |
vdslLinePerfVtucRxUncorrectedNumber of codewords left uncorrected after retransmission since last link up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.29 |
vdslLinePerfVturRxUncorrectedNumber of codewords left uncorrected after retransmission since last link up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.30 |
vdslLinePerfVtucLEFTRsLow Error-Free Throughput Rate Seconds since last link up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.31 |
vdslLinePerfVturLEFTRsLow Error-Free Throughput Rate Seconds since last link up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.32 |
vdslLinePerfVtucErrFreeBitsThe number of bits belonging to correct DTUs leaving the Rx PMS-TC x 2(-16) since last link up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.33 |
vdslLinePerfVturErrFreeBitsThe number of bits belonging to correct DTUs leaving the Rx PMS-TC x 2(-16) since last link up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.34 |
vdslLinePerfVtucMinEftrLowest EFTR of VTU-C observed since last link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.35 |
vdslLinePerfVturMinEftrLowest EFTR of VTU-R observed since last link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.1.1.36 |
vdslLineStatsTableThe table displays VDSL line statistics. This table is supported by R5.01 and later versions. SEQUENCE OF VdslLineStatsEntry .1.3.6.1.4.1.890.1.5.13.5.13.8.2 |
vdslLineStatsEntryAn entry of vdslLineStatsTable. VdslLineStatsEntry .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1 |
vdslLineStatsVtucBits1The object provides Bits for the VTU-C 1024 subcarriers.
Each subcarrier takes two octets to store the value.
The value is in the range 0 to 15.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.1 |
vdslLineStatsVtucBits2The object provides Bits for the VTU-C 1024 subcarriers.
Each subcarrier takes two octets to store the value.
The value is in the range 0 to 15.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.2 |
vdslLineStatsVtucBits3The object provides Bits for the VTU-C 1024 subcarriers.
Each subcarrier takes two octets to store the value.
The value is in the range 0 to 15.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.3 |
vdslLineStatsVtucBits4The object provides Bits for the VTU-C 1024 subcarriers.
Each subcarrier takes two octets to store the value.
The value is in the range 0 to 15.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.4 |
vdslLineStatsVturBits1The object provides Bits for the VTU-R 1024 subcarriers.
Each subcarrier takes two octets to store the value.
The value is in the range 0 to 15.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.5 |
vdslLineStatsVturBits2The object provides Bits for the VTU-R 1024 subcarriers.
Each subcarrier takes two octets to store the value.
The value is in the range 0 to 15.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.6 |
vdslLineStatsVturBits3The object provides Bits for the VTU-R 1024 subcarriers.
Each subcarrier takes two octets to store the value.
The value is in the range 0 to 15.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.7 |
vdslLineStatsVturBits4The object provides Bits for the VTU-R 1024 subcarriers.
Each subcarrier takes two octets to store the value.
The value is in the range 0 to 15.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.8 |
vdslLineStatsVtucGain1The object provides Gain for the VTU-C 512 subcarriers.
Each subcarrier takes two octets to store the value.
The value is in the range 0 to 4093. Each value in this array is 16 bits wide.
The gain value is represented as a multiple of 1/512 on linear scale.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.9 |
vdslLineStatsVtucGain2The object provides Gain for the VTU-C 512 subcarriers.
Each subcarrier takes two octets to store the value.
The value is in the range 0 to 4093. Each value in this array is 16 bits wide.
The gain value is represented as a multiple of 1/512 on linear scale.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.10 |
vdslLineStatsVtucGain3The object provides Gain for the VTU-C 512 subcarriers.
Each subcarrier takes two octets to store the value.
The value is in the range 0 to 4093. Each value in this array is 16 bits wide.
The gain value is represented as a multiple of 1/512 on linear scale.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.11 |
vdslLineStatsVtucGain4The object provides Gain for the VTU-C 512 subcarriers.
Each subcarrier takes two octets to store the value.
The value is in the range 0 to 4093. Each value in this array is 16 bits wide.
The gain value is represented as a multiple of 1/512 on linear scale.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.12 |
vdslLineStatsVtucGain5The object provides Gain for the VTU-C 512 subcarriers.
Each subcarrier takes two octets to store the value.
The value is in the range 0 to 4093. Each value in this array is 16 bits wide.
The gain value is represented as a multiple of 1/512 on linear scale.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.13 |
vdslLineStatsVtucGain6The object provides Gain for the VTU-C 512 subcarriers.
Each subcarrier takes two octets to store the value.
The value is in the range 0 to 4093. Each value in this array is 16 bits wide.
The gain value is represented as a multiple of 1/512 on linear scale.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.14 |
vdslLineStatsVtucGain7The object provides Gain for the VTU-C 512 subcarriers.
Each subcarrier takes two octets to store the value.
The value is in the range 0 to 4093. Each value in this array is 16 bits wide.
The gain value is represented as a multiple of 1/512 on linear scale.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.15 |
vdslLineStatsVtucGain8The object provides Gain for the VTU-C 512 subcarriers.
Each subcarrier takes two octets to store the value.
The value is in the range 0 to 4093. Each value in this array is 16 bits wide.
The gain value is represented as a multiple of 1/512 on linear scale.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.16 |
vdslLineStatsVturGain1The object provides Gain for the VTU-R 512 subcarriers.
Each subcarrier takes two octets to store the value.
The value is in the range 0 to 4093. Each value in this array is 16 bits wide.
The gain value is represented as a multiple of 1/512 on linear scale.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.17 |
vdslLineStatsVturGain2The object provides Gain for the VTU-R 512 subcarriers.
Each subcarrier takes two octets to store the value.
The value is in the range 0 to 4093. Each value in this array is 16 bits wide.
The gain value is represented as a multiple of 1/512 on linear scale.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.18 |
vdslLineStatsVturGain3The object provides Gain for the VTU-R 512 subcarriers.
Each subcarrier takes two octets to store the value.
The value is in the range 0 to 4093. Each value in this array is 16 bits wide.
The gain value is represented as a multiple of 1/512 on linear scale.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.19 |
vdslLineStatsVturGain4The object provides Gain for the VTU-R 512 subcarriers.
Each subcarrier takes two octets to store the value.
The value is in the range 0 to 4093. Each value in this array is 16 bits wide.
The gain value is represented as a multiple of 1/512 on linear scale.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.20 |
vdslLineStatsVturGain5The object provides Gain for the VTU-R 512 subcarriers.
Each subcarrier takes two octets to store the value.
The value is in the range 0 to 4093. Each value in this array is 16 bits wide.
The gain value is represented as a multiple of 1/512 on linear scale.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.21 |
vdslLineStatsVturGain6The object provides Gain for the VTU-R 512 subcarriers.
Each subcarrier takes two octets to store the value.
The value is in the range 0 to 4093. Each value in this array is 16 bits wide.
The gain value is represented as a multiple of 1/512 on linear scale.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.22 |
vdslLineStatsVturGain7The object provides Gain for the VTU-R 512 subcarriers.
Each subcarrier takes two octets to store the value.
The value is in the range 0 to 4093. Each value in this array is 16 bits wide.
The gain value is represented as a multiple of 1/512 on linear scale.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.23 |
vdslLineStatsVturGain8The object provides Gain for the VTU-R 512 subcarriers.
Each subcarrier takes two octets to store the value.
The value is in the range 0 to 4093. Each value in this array is 16 bits wide.
The gain value is represented as a multiple of 1/512 on linear scale.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.24 |
vdslLineStatsVtucHlogThe object provides Hlog for the VTU-C 512 subcarriers.
Each subcarrier takes two octets to store the value.
The real Hlog(f) value is represented as (6-m(i)/10), with m(i) in the range 0 to 1022.
A special value m=1023 indicates that no measurement could be done for the
sub-carrier group becauseit is out of the passband or that the attenuation
is out of range to be represented. Each value in this array is 16 bits wide.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.25 |
vdslLineStatsVturHlogThe object provides Hlog for the VTU-R 512 subcarriers.
Each subcarrier takes two octets to store the value.
The real Hlog(f) value is represented as (6-m(i)/10), with m(i) in the range 0 to 1022.
A special value m=1023 indicates that no measurement could be done for the
sub-carrier group because it is out of the passband or that the attenuation
is out ofrange to be represented. Each value in this array is 16 bits wide.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.26 |
vdslLineStatsVtucQlnThe object provides Qln for the VTU-C 512 subcarriers.
Each subcarrier takes two octets to store the value.
The QLN(f) is represented as ( -23-n(i)/2), with n(i) in the range 0 to 254.
A special value n(i)=255 indicates that no measurement could be done for the
sub-carrier group. Each value in this array is 8 bits wide.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.27 |
vdslLineStatsVturQlnThe object provides Qln for the VTU-R 512 subcarriers.
Each subcarrier takes two octets to store the value.
The QLN(f) is represented as ( -23-n(i)/2), with n(i) in the range 0 to 254.
A special value n(i)=255 indicates that no measurement could be done for the
sub-carrier group. Each value in this array is 8 bits wide.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.28 |
vdslLineStatsVtucSnrThe object provides Snr for the VTU-C 512 subcarriers.
Each subcarrier takes one octets to store the value.
Octet i is set to a value in the range 0 to 254 (-32 + vdslLineStatsVtucSnr (i)/2) in dB
(i.e., -32 to 95dB). Each value in this array is 8 bits wide.
A special value 255 indicates that no measurement could be done for the
sub-carrier group.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.29 |
vdslLineStatsVturSnrThe object provides Snr for the VTU-R 512 subcarriers.
Each subcarrier takes one octets to store the value.
Octet i is set to a value in the range 0 to 254 (-32 + vdslLineStatsVturSnr (i)/2) in dB
(i.e., -32 to 95dB). Each value in this array is 8 bits wide.
A special value 255 indicates that no measurement could be done for the
sub-carrier group.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.30 |
vdslLineStatsVtucTssiThe object provides Tssi for the VTU-C 512 subcarriers.
Each subcarrier takes two octets to store the value.
Each value in this array is 16 bits wide.
The tssi value is represented as a multiple of 1/32768 on linear scale.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.31 |
vdslLineStatsVturTssiThe object provides Tssi for the VTU-R 512 subcarriers.
Each subcarrier takes two octets to store the value.
Each value in this array is 16 bits wide.
The tssi value is represented as a multiple of 1/32768 on linear scale.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.32 |
vdslLineStatsProtocolThe actual line protocol.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.33 |
vdslLineStatsUsCodingModeThe upstream coding mode of the line. This object is supported by R5.02 and later versions.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.34 |
vdslLineStatsDsCodingModeThe downstream coding mode of the line. This object is supported by R5.02 and later versions.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.35 |
vdslLineStatsVtucHlogGroupSizeNumber of sub-carriers per group used to report the H(f) linear representation values for the
respective transmission direction. The valid values are 1, 2, 4 and 8.
This object is supported by R5.02 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.36 |
vdslLineStatsVturHlogGroupSizeNumber of sub-carriers per group used to report the H(f) linear representation values for the
respective transmission direction. The valid values are 1, 2, 4 and 8.
This object is supported by R5.02 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.37 |
vdslLineStatsVtucQlnGroupSizeNumber of sub-carriers per group used to report the Quiet Line Noise values for the
respective transmission direction. The valid values are 1, 2, 4 and 8.
This object is supported by R5.02 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.38 |
vdslLineStatsVturQlnGroupSizeNumber of sub-carriers per group used to report the Quiet Line Noise values for the
respective transmission direction. The valid values are 1, 2, 4 and 8.
This object is supported by R5.02 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.39 |
vdslLineStatsVtucSnrGroupSizeNumber of sub-carriers per group used to report the SNR values on the
respective transmission direction. The valid values are 1, 2, 4 and 8.
This object is supported by R5.02 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.40 |
vdslLineStatsVturSnrGroupSizeNumber of sub-carriers per group used to report the SNR values on the
respective transmission direction. The valid values are 1, 2, 4 and 8.
This object is supported by R5.02 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.41 |
vdslLineStatsVtucRxPowerReceive power of vtuc (in unit of 0.1 dBm).ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.42 |
vdslLineStatsVturRxPowerReceive power of vtur (in unit of 0.1 dBm).ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.43 |
vdslLineStatsVtucSnrMarginro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.44 |
vdslLineStatsVturSnrMarginro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.45 |
vdslLineStatsVtucSigAttenro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.46 |
vdslLineStatsVturSigAttenro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.47 |
vdslLineStatsVtucLineAttenro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.48 |
vdslLineStatsVturLineAttenro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.8.2.1.49 |
vdslLineUsBandPlanTableThe table displays VDSL line actual band plan. This table is supported by R5.01 and later versions. SEQUENCE OF VdslLineUsBandPlanEntry .1.3.6.1.4.1.890.1.5.13.5.13.8.3 |
vdslLineUsBandPlanEntryAn entry of vdslLineUsBandPlanTable. VdslLineUsBandPlanEntry .1.3.6.1.4.1.890.1.5.13.5.13.8.3.1 |
vdslLineUsBandIdIhe id of the upstream pass band, starting from 1.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.8.3.1.1 |
vdslLineUsBandStartToneIdThe starting tone of the band.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.8.3.1.2 |
vdslLineUsBandStopToneIdThe stopping tone of the band.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.8.3.1.3 |
vdslLineDsBandPlanTableThe table displays VDSL line actual band plan. This table is supported by R5.01 and later versions. SEQUENCE OF VdslLineDsBandPlanEntry .1.3.6.1.4.1.890.1.5.13.5.13.8.4 |
vdslLineDsBandPlanEntryAn entry of vdslLineDsBandPlanTable. VdslLineDsBandPlanEntry .1.3.6.1.4.1.890.1.5.13.5.13.8.4.1 |
vdslLineDsBandIdIhe id of the downstream pass band, starting from 1.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.8.4.1.1 |
vdslLineDsBandStartToneIdThe starting tone of the band.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.8.4.1.2 |
vdslLineDsBandStopToneIdThe stopping tone of the band.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.8.4.1.3 |
vdslLineUsResultMaskTableThe table displays VDSL line actual PSD mask. This table is supported by R5.01 and later versions. SEQUENCE OF VdslLineUsResultMaskEntry .1.3.6.1.4.1.890.1.5.13.5.13.8.5 |
vdslLineUsResultMaskEntryAn entry of vdslLineUsResultMaskTable. VdslLineUsResultMaskEntry .1.3.6.1.4.1.890.1.5.13.5.13.8.5.1 |
vdslLineUsMaskIdThe id of the turning point of the mask, starting from 1.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.8.5.1.1 |
vdslLineUsMaskToneThe tone id.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.8.5.1.2 |
vdslLineUsMaskPsdThe psd, in 0.1 dBm/Hz.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.8.5.1.3 |
vdslLineDsResultMaskTableThe table displays VDSL line actual PSD mask. This table is supported by R5.01 and later versions. SEQUENCE OF VdslLineDsResultMaskEntry .1.3.6.1.4.1.890.1.5.13.5.13.8.6 |
vdslLineDsResultMaskEntryAn entry of vdslLineDsResultMaskTable. VdslLineDsResultMaskEntry .1.3.6.1.4.1.890.1.5.13.5.13.8.6.1 |
vdslLineDsMaskIdThe id of the turning point of the mask, starting from 1.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.8.6.1.1 |
vdslLineDsMaskToneThe tone id.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.8.6.1.2 |
vdslLineDsMaskPsdThe psd, in 0.1 dBm/Hz.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.8.6.1.3 |
vdslLinePerfCurrTableThe table displays VDSL line current GINP/SOS/INM performance statistics. SEQUENCE OF VdslLinePerfCurrEntry .1.3.6.1.4.1.890.1.5.13.5.13.8.7 |
vdslLinePerfCurrEntryAn entry of vdslLinePerfCurrTable. VdslLinePerfCurrEntry .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1 |
vdslLinePerfCurrInmVtucEqInpThe INM Equivalent Inp histogram since system boot up. An array of 68 octets
(each 4 octets means amount of a bin of histogram), designed for supporting
from 1 to 17 bins of the histogram. The particular index of the bin incremented
by an impulse noise event is equal to the computed value of equivalent INP,
except the 17th of anomaly INPEQ, which logs all equivalent INPs greater than 16.
Each bin has a value in the range 0x0 to 0xFFFFFFFFro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.1 |
vdslLinePerfCurrInmVturEqInpThe INM Equivalent Inp histogram since system boot up. An array of 68 octets
(each 4 octets means amount of a bin of histogram), designed for supporting
from 1 to 17 bins of the histogram. The particular index of the bin incremented
by an impulse noise event is equal to the computed value of equivalent INP,
except the 17th of anomaly INPEQ, which logs all equivalent INPs greater than 16.
Each bin has a value in the range 0x0 to 0xFFFFFFFFro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.2 |
vdslLinePerfCurr15MInmVtucEqInpThe INM Equivalent Inp histogram during this 15 minutes interval. An array of 68 octets
(each 4 octets means amount of a bin of histogram), designed for supporting from 1 to 17
bins of the histogram. The particular index of the bin incremented by an impulse noise event
is equal to the computed value of equivalent INP, except the 17th of anomaly INPEQ, which logs
all equivalent INPs greater than 16. Each bin has a value in the range 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.3 |
vdslLinePerfCurr15MInmVturEqInpThe INM Equivalent Inp histogram during this 15 minutes interval. An array of 68 octets
(each 4 octets means amount of a bin of histogram), designed for supporting from 1 to 17
bins of the histogram. The particular index of the bin incremented by an impulse noise event
is equal to the computed value of equivalent INP, except the 17th of anomaly INPEQ, which logs
all equivalent INPs greater than 16. Each bin has a value in the range 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.4 |
vdslLinePerfCurr1DayInmVtucEqInpThe INM Equivalent Inp histogram during this 1 day interval. An array of 68 octets
(each 4 octets means amount of a bin of histogram), designed for supporting from 1 to 17
bins of the histogram. The particular index of the bin incremented by an impulse noise event
is equal to the computed value of equivalent INP, except the 17th of anomaly INPEQ, which logs
all equivalent INPs greater than 16. Each bin has a value in the range 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.5 |
vdslLinePerfCurr1DayInmVturEqInpThe INM Equivalent Inp histogram during this 1 day interval. An array of 68 octets
(each 4 octets means amount of a bin of histogram), designed for supporting from 1 to 17
bins of the histogram. The particular index of the bin incremented by an impulse noise event
is equal to the computed value of equivalent INP, except the 17th of anomaly INPEQ, which logs
all equivalent INPs greater than 16. Each bin has a value in the range 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.6 |
vdslLinePerfCurrInmVtucIATThe INM Inter Arrival Time histogram since system boot up. An array of 32 octets
(each 4 octets means amount of a bin of histogram), designed for supporting from 0 to 7
bins of the histogram. The index of the particular bin incremented by an complete impulse noise event
is determained from the following INMControl parameters. Each bin has a value in the range 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.7 |
vdslLinePerfCurrInmVturIATThe INM Inter Arrival Time histogram since system boot up. An array of 32 octets
(each 4 octets means amount of a bin of histogram), designed for supporting from 0 to 7
bins of the histogram. The index of the particular bin incremented by an complete impulse noise event
is determained from the following INMControl parameters. Each bin has a value in the range 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.8 |
vdslLinePerfCurr15MInmVtucIATThe INM Inter Arrival Time histogram during this 15 minutes interval. An array of 32 octets
(each 4 octets means amount of a bin of histogram), designed for supporting from 0 to 7 bins of the histogram.
The index of the particular bin incremented by an complete impulse noise event is determained from the following
INMControl parameters. Each bin has a value in the range 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.9 |
vdslLinePerfCurr15MInmVturIATThe INM Inter Arrival Time histogram during this 15 minutes interval. An array of 32 octets
(each 4 octets means amount of a bin of histogram), designed for supporting from 0 to 7 bins of the histogram.
The index of the particular bin incremented by an complete impulse noise event is determained from the following
INMControl parameters. Each bin has a value in the range 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.10 |
vdslLinePerfCurr1DayInmVtucIATThe INM Inter Arrival Time histogram during this 1 day interval. An array of 32 octets
(each 4 octets means amount of a bin of histogram), designed for supporting from 0 to 7 bins of the histogram.
The index of the particular bin incremented by an complete impulse noise event is determained from the following
INMControl parameters. Each bin has a value in the range 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.11 |
vdslLinePerfCurr1DayInmVturIATThe INM Inter Arrival Time histogram during this 1 day interval. An array of 32 octets
(each 4 octets means amount of a bin of histogram), designed for supporting from 0 to 7 bins of the histogram.
The index of the particular bin incremented by an complete impulse noise event is determained from the following
INMControl parameters. Each bin has a value in the range 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.12 |
vdslLinePerfCurrInmVtucMEThe INM total measurement since system boot up. This indication occurs every time
a data symbol is processed by the Impulse Noise Sensor. The range of the value is from 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.13 |
vdslLinePerfCurrInmVturMEThe INM total measurement since system boot up. This indication occurs every time
a data symbol is processed by the Impulse Noise Sensor. The range of the value is from 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.14 |
vdslLinePerfCurr15MInmVtucMEThe INM total measurement during this 15 minutes interval. This indication occurs every time
a data symbol is processed by the Impulse Noise Sensor. The range of the value is from 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.15 |
vdslLinePerfCurr15MInmVturMEThe INM total measurement during this 15 minutes interval. This indication occurs every time
a data symbol is processed by the Impulse Noise Sensor. The range of the value is from 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.16 |
vdslLinePerfCurr1DayInmVtucMEThe INM total measurement during this 1 day interval. This indication occurs every time
a data symbol is processed by the Impulse Noise Sensor. The range of the value is from 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.17 |
vdslLinePerfCurr1DayInmVturMEThe INM total measurement during this 1 day interval. This indication occurs every time
a data symbol is processed by the Impulse Noise Sensor. The range of the value is from 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.18 |
vdslLinePerfCurrVtucRxNumber of codewords retransmitted since system boot up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.19 |
vdslLinePerfCurrVturRxNumber of codewords retransmitted since system boot up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.20 |
vdslLinePerfCurr15MVtucRxNumber of codewords retransmitted during this 15 minutes interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.21 |
vdslLinePerfCurr15MVturRxNumber of codewords retransmitted during this 15 minutes interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.22 |
vdslLinePerfCurr1DayVtucRxNumber of codewords retransmitted during this 1 day interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.23 |
vdslLinePerfCurr1DayVturRxNumber of codewords retransmitted during this 1 day interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.24 |
vdslLinePerfCurrVtucRxCorrectedNumber of codewords corrected through retransmission since system boot up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.25 |
vdslLinePerfCurrVturRxCorrectedNumber of codewords corrected through retransmission since system boot up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.26 |
vdslLinePerfCurr15MVtucRxCorrectedNumber of codewords corrected through retransmission during this 15 minutes interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.27 |
vdslLinePerfCurr15MVturRxCorrectedNumber of codewords corrected through retransmission during this 15 minutes interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.28 |
vdslLinePerfCurr1DayVtucRxCorrectedNumber of codewords corrected through retransmission during this 1 day interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.29 |
vdslLinePerfCurr1DayVturRxCorrectedNumber of codewords corrected through retransmission during this 1 day interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.30 |
vdslLinePerfCurrVtucRxUncorrectedNumber of codewords left uncorrected after retransmission since system boot up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.31 |
vdslLinePerfCurrVturRxUncorrectedNumber of codewords left uncorrected after retransmission since system boot up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.32 |
vdslLinePerfCurr15MVtucRxUncorrectedNumber of codewords left uncorrected after retransmission during this 15 minutes interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.33 |
vdslLinePerfCurr15MVturRxUncorrectedNumber of codewords left uncorrected after retransmission during this 15 minutes interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.34 |
vdslLinePerfCurr1DayVtucRxUncorrectedNumber of codewords left uncorrected after retransmission during this 1 day interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.35 |
vdslLinePerfCurr1DayVturRxUncorrectedNumber of codewords left uncorrected after retransmission during this 1 day interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.36 |
vdslLinePerfCurrVtucLEFTRsLow Error-Free Throughput Rate Seconds since system boot up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.37 |
vdslLinePerfCurrVturLEFTRsLow Error-Free Throughput Rate Seconds since system boot up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.38 |
vdslLinePerfCurr15MVtucLEFTRsLow Error-Free Throughput Rate Seconds during this 15 minutes interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.39 |
vdslLinePerfCurr15MVturLEFTRsLow Error-Free Throughput Rate Seconds during this 15 minutes interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.40 |
vdslLinePerfCurr1DayVtucLEFTRsLow Error-Free Throughput Rate Seconds during this 1 day interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.41 |
vdslLinePerfCurr1DayVturLEFTRsLow Error-Free Throughput Rate Seconds during this 1 day interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.42 |
vdslLinePerfCurrVtucErrFreeBitsThe number of bits belonging to correct DTUs leaving the Rx PMS-TC x 2(-16) since system boot up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.43 |
vdslLinePerfCurrVturErrFreeBitsThe number of bits belonging to correct DTUs leaving the Rx PMS-TC x 2(-16) since system boot up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.44 |
vdslLinePerfCurr15MVtucErrFreeBitsThe number of bits belonging to correct DTUs leaving the Rx PMS-TC x 2(-16) during this 15 minutes interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.45 |
vdslLinePerfCurr15MVturErrFreeBitsThe number of bits belonging to correct DTUs leaving the Rx PMS-TC x 2(-16) during this 15 minutes interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.46 |
vdslLinePerfCurr1DayVtucErrFreeBitsThe number of bits belonging to correct DTUs leaving the Rx PMS-TC x 2(-16) this 1 day interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.47 |
vdslLinePerfCurr1DayVturErrFreeBitsThe number of bits belonging to correct DTUs leaving the Rx PMS-TC x 2(-16) this 1 day interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.48 |
vdslLinePerfCurrVtucMinEftrLowest EFTR of VTU-C observed in the current interval.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.49 |
vdslLinePerfCurrVturMinEftrLowest EFTR of VTU-R observed in the current interval.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.50 |
vdslLinePerfCurr15MinVtucMinEftrLowest EFTR of VTU-C observed in the current 15 minutes interval.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.51 |
vdslLinePerfCurr15MinVturMinEftrLowest EFTR of VTU-R observed in the current 15 minutes interval.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.52 |
vdslLinePerfCurr1DayVtucMinEftrLowest EFTR of VTU-C observed in the current 1 day interval.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.53 |
vdslLinePerfCurr1DayVturMinEftrLowest EFTR of VTU-R observed in the current 1 day interval.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.7.1.54 |
vdslLinePerfHist15MinTableThe table displays VDSL line 15-Min SOS/GINP/INM performance stats. SEQUENCE OF VdslLinePerfHist15MinEntry .1.3.6.1.4.1.890.1.5.13.5.13.8.8 |
vdslLinePerfHist15MinEntryAn entry of vdslLinePerfCurrTable. VdslLinePerfHist15MinEntry .1.3.6.1.4.1.890.1.5.13.5.13.8.8.1 |
vdslLinePerfHist15MInmVtucEqInpThe INM Equivalent Inp histogram during 15min interval. An array of 68 octets
(each 4 octets means amount of a bin of histogram), designed for supporting from
1 to 17 bins of the histogram. The particular index of the bin incremented by an
impulse noise event is equal to the computed value of equivalent INP, except the
17th of anomaly INPEQ, which logs all equivalent INPs greater than 16. Each bin
has a value in the range 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.8.1.1 |
vdslLinePerfHist15MInmVturEqInpThe INM Equivalent Inp histogram during 15min interval. An array of 68 octets
(each 4 octets means amount of a bin of histogram), designed for supporting from
1 to 17 bins of the histogram. The particular index of the bin incremented by an
impulse noise event is equal to the computed value of equivalent INP, except the
17th of anomaly INPEQ, which logs all equivalent INPs greater than 16. Each bin
has a value in the range 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.8.1.2 |
vdslLinePerfHist15MInmVtucIATThe INM Inter Arrival Time histogram during 15min interval. An array of 32 octets
(each 4 octets means amount of a bin of histogram), designed for supporting from 0
to 7 bins of the histogram. The index of the particular bin incremented by an complete
impulse noise event is determained from the following INMControl parameters. Each bin
has a value in the range 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.8.1.3 |
vdslLinePerfHist15MInmVturIATThe INM Inter Arrival Time histogram during 15min interval. An array of 32 octets
(each 4 octets means amount of a bin of histogram), designed for supporting from 0
to 7 bins of the histogram. The index of the particular bin incremented by an complete
impulse noise event is determained from the following INMControl parameters. Each bin
has a value in the range 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.8.1.4 |
vdslLinePerfHist15MInmVtucMEThe INM total measurement during 15min interval.This indication occurs every time
a data symbol is processed by the Impulse Noise Sensor. The range of the value is
from 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.8.1.5 |
vdslLinePerfHist15MInmVturMEThe INM total measurement during 15min interval.This indication occurs every time
a data symbol is processed by the Impulse Noise Sensor. The range of the value is
from 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.8.1.6 |
vdslLinePerfHist15MVtucRtxNumber of codewords retransmitted during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.8.1.7 |
vdslLinePerfHist15MVturRtxNumber of codewords retransmitted during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.8.1.8 |
vdslLinePerfHist15MVtucRtxCorrectedNumber of codewords corrected through retransmission during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.8.1.9 |
vdslLinePerfHist15MVturRtxCorrectedNumber of codewords corrected through retransmission during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.8.1.10 |
vdslLinePerfHist15MVtucRtxUncorrectedNumber of codewords left uncorrected after retransmission during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.8.1.11 |
vdslLinePerfHist15MVturRtxUncorrectedNumber of codewords left uncorrected after retransmission during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.8.1.12 |
vdslLinePerfHist15MVtucLEFTRsLow Error-Free Throughput Rate Seconds during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.8.1.13 |
vdslLinePerfHist15MVturLEFTRsLow Error-Free Throughput Rate Seconds during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.8.1.14 |
vdslLinePerfHist15MVtucErrFreeBitsThe number of bits belonging to correct DTUs leaving the Rx PMS-TC x 2(-16) during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.8.1.15 |
vdslLinePerfHist15MVturErrFreeBitsThe number of bits belonging to correct DTUs leaving the Rx PMS-TC x 2(-16) during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.8.1.16 |
vdslLinePerfHist15MVtucMinEftrLowest EFTR of VTU-C observed during this interval.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.8.1.17 |
vdslLinePerfHist15MVturMinEftrLowest EFTR of VTU-R observed during this interval.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.8.1.18 |
vdslLinePerfHist1DayTableThe table displays VDSL line 1-Day SOS/GINP/INM performance stats. SEQUENCE OF VdslLinePerfHist1DayEntry .1.3.6.1.4.1.890.1.5.13.5.13.8.9 |
vdslLinePerfHist1DayEntryAn entry of vdslLinePerfHist1DayTable. VdslLinePerfHist1DayEntry .1.3.6.1.4.1.890.1.5.13.5.13.8.9.1 |
vdslLinePerfHist1DayInmVtucEqInpThe INM Equivalent Inp histogram during 1 day interval. An array of 68 octets
(each 4 octets means amount of a bin of histogram), designed for supporting from
1 to 17 bins of the histogram. The particular index of the bin incremented by an
impulse noise event is equal to the computed value of equivalent INP, except the
17th of anomaly INPEQ, which logs all equivalent INPs greater than 16. Each bin
has a value in the range 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.9.1.1 |
vdslLinePerfHist1DayInmVturEqInpThe INM Equivalent Inp histogram during 1 day interval. An array of 68 octets
(each 4 octets means amount of a bin of histogram), designed for supporting from
1 to 17 bins of the histogram. The particular index of the bin incremented by an
impulse noise event is equal to the computed value of equivalent INP, except the
17th of anomaly INPEQ, which logs all equivalent INPs greater than 16. Each bin
has a value in the range 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.9.1.2 |
vdslLinePerfHist1DayInmVtucIATThe INM Inter Arrival Time histogram during 1 day interval. An array of 32 octets
(each 4 octets means amount of a bin of histogram), designed for supporting from 0
to 7 bins of the histogram. The index of the particular bin incremented by an complete
impulse noise event is determained from the following INMControl parameters. Each bin
has a value in the range 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.9.1.3 |
vdslLinePerfHist1DayInmVturIATThe INM Inter Arrival Time histogram during 1 day interval. An array of 32 octets
(each 4 octets means amount of a bin of histogram), designed for supporting from 0
to 7 bins of the histogram. The index of the particular bin incremented by an complete
impulse noise event is determained from the following INMControl parameters. Each bin
has a value in the range 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.9.1.4 |
vdslLinePerfHist1DayInmVtucMEThe INM total measurement during 1 day interval.This indication occurs every time
a data symbol is processed by the Impulse Noise Sensor. The range of the value is
from 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.9.1.5 |
vdslLinePerfHist1DayInmVturMEThe INM total measurement during 1 day interval.This indication occurs every time
a data symbol is processed by the Impulse Noise Sensor. The range of the value is
from 0x0 to 0xFFFFFFFF.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.9.1.6 |
vdslLinePerfHist1DayVtucRtxNumber of codewords retransmitted during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.9.1.7 |
vdslLinePerfHist1DayVturRtxNumber of codewords retransmitted during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.9.1.8 |
vdslLinePerfHist1DayVtucRtxCorrectedNumber of codewords corrected through retransmission during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.9.1.9 |
vdslLinePerfHist1DayVturRtxCorrectedNumber of codewords corrected through retransmission during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.9.1.10 |
vdslLinePerfHist1DayVtucRtxUncorrectedNumber of codewords left uncorrected after retransmission during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.9.1.11 |
vdslLinePerfHist1DayVturRtxUncorrectedNumber of codewords left uncorrected after retransmission during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.9.1.12 |
vdslLinePerfHist1DayVtucLEFTRsLow Error-Free Throughput Rate Seconds during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.9.1.13 |
vdslLinePerfHist1DayVturLEFTRsLow Error-Free Throughput Rate Seconds during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.9.1.14 |
vdslLinePerfHist1DayVtucErrFreeBitsThe number of bits belonging to correct DTUs leaving the Rx PMS-TC x 2(-16) during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.9.1.15 |
vdslLinePerfHist1DayVturErrFreeBitsThe number of bits belonging to correct DTUs leaving the Rx PMS-TC x 2(-16) during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.8.9.1.16 |
vdslLinePerfHist1DayVtucMinEftrLowest EFTR of VTU-C observed during this interval.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.9.1.17 |
vdslLinePerfHist1DayVturMinEftrLowest EFTR of VTU-R observed during this interval.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.8.9.1.18 |
vdslChanStatsTableThe table displays VDSL channel Status. SEQUENCE OF VdslChanStatsEntry .1.3.6.1.4.1.890.1.5.13.5.13.8.10 |
vdslChanStatsEntryAn entry of vdslChanStatsTable. VdslChanStatsEntry .1.3.6.1.4.1.890.1.5.13.5.13.8.10.1 |
paepvcStats OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.9 |
paepvcSessionTableThis table shows the paepvc session statistics.
This table is supported by R1.03 and later versions. SEQUENCE OF PaepvcSessionEntry .1.3.6.1.4.1.890.1.5.13.5.13.9.1 |
paepvcSessionEntryAn entry of paepvcSessionTable. PaepvcSessionEntry .1.3.6.1.4.1.890.1.5.13.5.13.9.1.1 |
paepvcSessionVpiThe PAEPVC VPI.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.9.1.1.1 |
paepvcSessionVciThe PAEPVC VCI.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.9.1.1.2 |
paepvcSessionStateThe PAEPVC status.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.9.1.1.3 |
paepvcSessionIdThe PAEPVC session ID.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.9.1.1.4 |
paepvcSessionUpTimeThe PAEPVC session uptime.ro Unsigned32 UNITS "second" .1.3.6.1.4.1.890.1.5.13.5.13.9.1.1.5 |
paepvcSessionAcNameAccess concentrator name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.9.1.1.6 |
paepvcSessionSrvcNameService name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.9.1.1.7 |
paepvcCountTableThis table shows the paepvc counters.
This table is supported by R1.03 and later versions. SEQUENCE OF PaepvcCountEntry .1.3.6.1.4.1.890.1.5.13.5.13.9.2 |
paepvcCountEntryAn entry of paepvcCountTable. PaepvcCountEntry .1.3.6.1.4.1.890.1.5.13.5.13.9.2.1 |
paepvcCountVpiThe PAEPVC VPI.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.9.2.1.1 |
paepvcCountVciThe PAEPVC VCI.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.9.2.1.2 |
paepvcCountPppLcpCfgReqRxThe number of ppp lcp config-request received.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.9.2.1.3 |
paepvcCountPppLcpEchoReqRxThe number of ppp lcp echo-request received.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.9.2.1.4 |
paepvcCountPppLcpEchoReplyRxThe number of ppp lcp echo-reply received.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.9.2.1.5 |
paepvcCountPadiTxThe number of pppoe padi transfered.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.9.2.1.6 |
paepvcCountPadoRxThe number of pppoe pado received.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.9.2.1.7 |
paepvcCountPadrTxThe number of pppoe padr received.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.9.2.1.8 |
paepvcCountPadsRxThe number of pppoe pads received.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.9.2.1.9 |
paepvcCountPadtTxThe number of pppoe padt transfered.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.9.2.1.10 |
paepvcCountPadtRxThe number of pppoe padt received.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.9.2.1.11 |
paepvcCountSrvcnameErrRxThe number of pppoe service name error received.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.9.2.1.12 |
paepvcCountAcnameErrRxThe number of pppoe access concentrator name error received.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.9.2.1.13 |
paepvcCountGenericErrTxThe number of pppoe generic error transfered.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.9.2.1.14 |
paepvcCountGenericErrRxThe number of pppoe generic error received.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.9.2.1.15 |
vlanMacStats OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.10 |
vlanMacDisplayTargetThis managed object is a filter used for identify the target from which
the MAC addresses are learned in macTable. Ifindex is used to specify a specific
interface of which the MAC addresses are displayed. Some values are reserved for
special purpose, they are:
0: All interfaces
50: All uplink portsrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.10.1 |
vlanMacDisplayVidThis object is supported by R1.03 and later versions.
This managed object is a filter used for identifying the target
from which the MAC addresses are learned in vlanMacTable. The value of zero
means no filtering.rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.10.2 |
vlanMacTableThis table is supported by R1.03 and later versions.
A table that contains information about unicast
entries for which the bridge has forwarding and/or
filtering information. This information is used
by the transparent bridging function in
determining how to propagate a received frame. SEQUENCE OF VlanMacEntry .1.3.6.1.4.1.890.1.5.13.5.13.10.3 |
vlanMacEntryAn entry of vlanMacTable. VlanMacEntry .1.3.6.1.4.1.890.1.5.13.5.13.10.3.1 |
vlanMacAddressA unicast MAC address for which the bridge has
forwarding and/or filtering information.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.10.3.1.1 |
vlanMacPortThe port from which the mac address has been learned.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.10.3.1.2 |
vlanMacStatusThe status of this entry.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.10.3.1.3 |
ipbpvcStats OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.11 |
arpproxyTableDisplay ARP table. This table is supported by R3.00 and later versions. SEQUENCE OF ArpproxyEntry .1.3.6.1.4.1.890.1.5.13.5.13.11.1 |
arpproxyEntryAn entry of arpproxyTable. ArpproxyEntry .1.3.6.1.4.1.890.1.5.13.5.13.11.1.1 |
arpproxyIpro IpAddress .1.3.6.1.4.1.890.1.5.13.5.13.11.1.1.1 |
arpproxyMacro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.11.1.1.2 |
arpproxyIfIndexro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.11.1.1.3 |
arpproxyVpiro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.11.1.1.4 |
arpproxyVciro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.11.1.1.5 |
arpproxyInterfaceIpro IpAddress .1.3.6.1.4.1.890.1.5.13.5.13.11.1.1.6 |
arpproxyInterfaceMaskro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.11.1.1.7 |
arpproxyInterfaceVidro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.11.1.1.8 |
arpproxyDhcpIpro Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.11.1.1.9 |
arpproxyTypero Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.11.1.1.10 |
ipbpvcIfDynamicTableDisplay runtime interfaces. This table is supported by R3.00 and later versions. SEQUENCE OF IpbpvcIfDynamicEntry .1.3.6.1.4.1.890.1.5.13.5.13.11.2 |
ipbpvcIfDynamicEntryAn entry of ipbpvcIfDynamicTable. IpbpvcIfDynamicEntry .1.3.6.1.4.1.890.1.5.13.5.13.11.2.1 |
ipbpvcIfDynamicIpro IpAddress .1.3.6.1.4.1.890.1.5.13.5.13.11.2.1.1 |
ipbpvcIfDynamicMaskro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.11.2.1.2 |
ipbpvcIfDynamicIfIndexro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.11.2.1.3 |
ipbpvcIfDynamicVpiro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.11.2.1.4 |
ipbpvcIfDynamicVciro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.11.2.1.5 |
ipbpvcRouteDynamicTableDisplay runtime routing table. This table is supported by R3.00 and later versions. SEQUENCE OF IpbpvcRouteDynamicEntry .1.3.6.1.4.1.890.1.5.13.5.13.11.3 |
ipbpvcRouteDynamicEntryAn entry of ipbpvcRouteDynamicTable. IpbpvcRouteDynamicEntry .1.3.6.1.4.1.890.1.5.13.5.13.11.3.1 |
ipbpvcRouteDynamicTypero Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.11.3.1.1 |
ipbpvcRouteDynamicIpro IpAddress .1.3.6.1.4.1.890.1.5.13.5.13.11.3.1.2 |
ipbpvcRouteDynamicMaskro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.11.3.1.3 |
ipbpvcRouteDynamicNextHopro IpAddress .1.3.6.1.4.1.890.1.5.13.5.13.11.3.1.4 |
ipbpvcRouteDynamicMetricro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.11.3.1.5 |
ipbpvcRouteDynamicPriorityro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.11.3.1.6 |
voipStats OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.12 |
voipLineStatusTableThe table displays VoIP line status. This table is supported by R4.01 and later versions. SEQUENCE OF VoipLineStatusEntry .1.3.6.1.4.1.890.1.5.13.5.13.12.1 |
voipLineStatusEntryAn entry of voipLineStatusTable. VoipLineStatusEntry .1.3.6.1.4.1.890.1.5.13.5.13.12.1.1 |
voipLineStatusFxsStatusFXS status of the line.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.12.1.1.1 |
voipLineStatusServiceStatusService status of the line.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.12.1.1.2 |
voipLineInfoTableThe table displays VoIP line information. This table is supported by R4.01 and later versions. SEQUENCE OF VoipLineInfoEntry .1.3.6.1.4.1.890.1.5.13.5.13.12.2 |
voipLineInfoEntryAn entry of voipLineInfoTable. VoipLineInfoEntry .1.3.6.1.4.1.890.1.5.13.5.13.12.2.1 |
voipLineInfoSipLocalUriro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.12.2.1.1 |
voipLineInfoSipRemoteUriro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.12.2.1.2 |
voipLineInfoRtpTxCodecTypero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.12.2.1.3 |
voipLineInfoRtpRxCodecTypero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.12.2.1.4 |
voipLineInfoRtpTxPt1: g711mu(0)
2: g711a(8)
3: g723(4)
4: g729(18)
5: g726-16(96)
6: g726-24(97)
7: g728-32(98)
8: g728-40(99)ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.2.1.5 |
voipLineInfoRtpRxPt1: g711mu(0)
2: g711a(8)
3: g723(4)
4: g729(18)
5: g726-16(96)
6: g726-24(97)
7: g728-32(98)
8: g728-40(99)ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.2.1.6 |
voipLineInfoRtpLocalIpro IpAddress .1.3.6.1.4.1.890.1.5.13.5.13.12.2.1.7 |
voipLineInfoRtpRemoteIpro IpAddress .1.3.6.1.4.1.890.1.5.13.5.13.12.2.1.8 |
voipLineInfoRtpLocalPortro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.2.1.9 |
voipLineInfoRtpRemotePortro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.2.1.10 |
voipLineInfoLastCidModero Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.12.2.1.11 |
voipLineInfoPlaySignalTelro Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.12.2.1.12 |
voipLineInfoPlaySignalNetro Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.12.2.1.13 |
voipH248StatTableThe table displays registration status of media gateway.
This table is supported by R5.01 and later versions. SEQUENCE OF VoipH248StatEntry .1.3.6.1.4.1.890.1.5.13.5.13.12.3 |
voipH248StatEntryAn entry of voipH248StatTable. VoipH248StatEntry .1.3.6.1.4.1.890.1.5.13.5.13.12.3.1 |
voipH248StatSlotLine card slot number.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.3.1.1 |
voipH248StatMgNameMG name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.12.3.1.2 |
voipH248StatMgStateMG state.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.12.3.1.3 |
voipSipStatTableThe table displays the status of SIP proxy server while oolocal calloo feature is enabled.
This table is supported by R5.01 and later versions. SEQUENCE OF VoipSipStatEntry .1.3.6.1.4.1.890.1.5.13.5.13.12.4 |
voipSipStatEntryAn entry of voipSipStatTable. VoipSipStatEntry .1.3.6.1.4.1.890.1.5.13.5.13.12.4.1 |
voipSipStatSlotLine card slot number.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.4.1.1 |
voipSipStatProxyIndexro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.4.1.2 |
voipSipStatProxySvrProxy server IP or proxy server doamin name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.12.4.1.3 |
voipSipStatProxyPortProxy server port.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.4.1.4 |
voipSipStatStatero Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.12.4.1.5 |
voipH248InterfaceStatTable SEQUENCE OF VoipH248InterfaceStatEntry .1.3.6.1.4.1.890.1.5.13.5.13.12.5 |
voipH248InterfaceStatEntryAn entry of voipH248InterfaceStatTable. VoipH248InterfaceStatEntry .1.3.6.1.4.1.890.1.5.13.5.13.12.5.1 |
voipH248InterfaceStatIdLine card slot number.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.5.1.1 |
voipH248InterfaceStatMgStateMg Statero Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.12.5.1.2 |
voipH248InterfaceStatPrimarySlotPrimary Slotro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.5.1.3 |
voipH248InterfaceStatSecondarySlotSecondary Slotro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.5.1.4 |
voipH248InterfaceStatPrimaryProtectionStatePrimary Protection Statero Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.12.5.1.5 |
voipH248InterfaceStatSecondaryProtectionStateSecondary Protection Statero Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.12.5.1.6 |
voipH248InterfaceStatRedundantStateRedundant Statero Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.12.5.1.7 |
voipH248MediaStatTable SEQUENCE OF VoipH248MediaStatEntry .1.3.6.1.4.1.890.1.5.13.5.13.12.6 |
voipH248MediaStatEntryAn entry of voipH248MediaStatTable. VoipH248MediaStatEntry .1.3.6.1.4.1.890.1.5.13.5.13.12.6.1 |
voipH248MediaStatInterfaceIdInterface ID.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.6.1.1 |
voipH248MediaStatSlaveIdMedia IDro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.6.1.2 |
voipH248MediaStatSlaveIpMedia Ipro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.6.1.3 |
voipH248MediaStatMgmtInbandIpManagement Inband Ipro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.6.1.4 |
voipH248MediaStatMgmtOutbandIpManagement Onband Ipro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.6.1.5 |
voipH248MediaStatSlotIdslot idro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.6.1.6 |
voipH248MediaStatPortCountport countro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.6.1.7 |
voipH248MediaStatStatestatero Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.12.6.1.8 |
voipH248TerminationStatTable SEQUENCE OF VoipH248TerminationStatEntry .1.3.6.1.4.1.890.1.5.13.5.13.12.7 |
voipH248TerminationStatEntryAn entry of voipH248TerminationStatStateTable. VoipH248TerminationStatEntry .1.3.6.1.4.1.890.1.5.13.5.13.12.7.1 |
voipH248TerminationStatStateIdInterface Id of the termination.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.7.1.1 |
voipH248TerminationStatStateMediaIdMedia Card Id of the termination.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.7.1.2 |
voipH248TerminationStatStatePortNumberPort number the termination.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.7.1.3 |
voipH248TerminationStatNameTermination Name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.12.7.1.4 |
voipH248TerminationStatPhoneStatePhone Statero Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.12.7.1.5 |
voipH248TerminationStatCallServiceStateCall Service Statero Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.12.7.1.6 |
voipH248TerminationStatQuery OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.12.8 |
voipH248TerminationStatQueryInterfaceIdInterface Idrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.8.1 |
voipH248TerminationStatQueryTerminationNameTermination Namerw DisplayString .1.3.6.1.4.1.890.1.5.13.5.13.12.8.2 |
voipH248TerminationStatQuerySlaveIdSlave Idro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.8.3 |
voipH248TerminationStatQuerySlaveIpSlave Ipro IpAddress .1.3.6.1.4.1.890.1.5.13.5.13.12.8.4 |
voipH248TerminationStatQueryMgmtInbandIpManagement Inband Ipro IpAddress .1.3.6.1.4.1.890.1.5.13.5.13.12.8.5 |
voipH248TerminationStatQueryMgmtOutbandIpManagement Outband Ipro IpAddress .1.3.6.1.4.1.890.1.5.13.5.13.12.8.6 |
voipH248TerminationStatQuerySlotIdSlot Idro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.8.7 |
voipH248TerminationStatQueryPortCountPort Countro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.8.8 |
voipH248TerminationStatQueryStateStatero Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.12.8.9 |
voipH248TerminationStatQueryPortNumberPort Numberro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.8.10 |
voipH248TerminationStatQueryPhoneStatePhone Statero Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.12.8.11 |
voipH248TerminationStatQueryCallServiceStateCallService Statero Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.12.8.12 |
voipRtpStatTable SEQUENCE OF VoipRtpStatEntry .1.3.6.1.4.1.890.1.5.13.5.13.12.9 |
voipRtpStatEntryAn entry of voipRtpStatTable. VoipRtpStatEntry .1.3.6.1.4.1.890.1.5.13.5.13.12.9.1 |
voipRtpStatTxRatereal-time RTP tx packet rate in bps.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.9.1.1 |
voipRtpStatRxRatereal-time RTP rx packet rate in bps.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.9.1.2 |
voipRtpStatTxPktCnttotal RTP tx packet counter for current/last call.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.12.9.1.3 |
voipRtpStatRxPktCnttotal RTP rx packet counter for current/last call.ro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.12.9.1.4 |
voipRtpStatTxFracLostRTP Tx packet lost in percentagero INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.9.1.5 |
voipRtpStatRxFracLostRTP Rx packet lost in percentagero INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.9.1.6 |
voipRtpStatTxJitterTX jitter in micro-secondro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.12.9.1.7 |
voipRtpStatRxJitterRx jitter in micro-secondro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.12.9.1.8 |
voipRtpStatTxAvgDelayAverage Tx delay in msro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.12.9.1.9 |
voipRtpStatRxAvgDelayAverage Rx delay in msro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.12.9.1.10 |
voipCdrStat OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.12.10 |
voipCdrStatFilter OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.1 |
voipCdrStatFilterInterfaceInterface id.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.1.1 |
voipCdrStatFilterIndexEnableSet 0 to clear voipCdrStatFilterIndex.
It will show 1 if voipCdrStatFilterIndex had been set before.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.1.2 |
voipCdrStatFilterIndexIndex filter.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.1.3 |
voipCdrStatFilterSlotPortEnableSet 0 to clear voipCdrStatFilterSlot and voipCdrStatFilterPort.
It will show 1 if voipCdrStatFilterSlot and voipCdrStatFilterPort had been set before.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.1.4 |
voipCdrStatFilterSlotSlot filter.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.1.5 |
voipCdrStatFilterPortPort filter, 0 mean select all portrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.1.6 |
voipCdrStatFilterRtpElpasedTimeEnableSet 0 to clear voipCdrStatFilterRtpElpasedTimeMin and voipCdrStatFilterRtpElpasedTimeMax. It will show 1 if any of them had been set before.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.1.7 |
voipCdrStatFilterRtpElpasedTimeMinin unit of secondrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.1.8 |
voipCdrStatFilterRtpElpasedTimeMaxin unit of secondrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.1.9 |
voipCdrStatFilterTelEnableSet 0 to clear voipCdrStatFilterTel. It will show 1 if voipCdrStatFilterTel had been set before.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.1.10 |
voipCdrStatFilterTelTelephone number filter, max length is 24.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.12.10.1.11 |
voipCdrStatFilterOffhookEnableSet 0 to clear voipCdrStatFilterOffhookDateMin, voipCdrStatFilterOffhookTimeMin, voipCdrStatFilterOffhookDateMax,
and voipCdrStatFilterOffhookDateMax . It will show 1 if any of them had been set before.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.1.12 |
voipCdrStatFilterOffhookDateMinMinimum offhook date filter, format example:20120101rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.1.13 |
voipCdrStatFilterOffhookTimeMinMinimum offhook time filter, format example:235959rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.1.14 |
voipCdrStatFilterOffhookDateMaxMaximum offhook date filter, format example:20120101rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.1.15 |
voipCdrStatFilterOffhookTimeMaxMaximum offhook time filter, format example:235959rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.1.16 |
voipCdrStatFilterCodeEnableSet 0 to clear voipCdrStatFilterCode. It will show 1 if voipCdrStatFilterCode had been set before.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.1.17 |
voipCdrStatFilterCodeCode filter. It is a bit map of the call state record.
bit 6(0x20): offhook
bit 5(0x10): remote ringback tone
bit 4(0x08): local ringback tone
bit 3(0x04): dial tone
bit 2(0x02): ring
bit 1(0x01): rtprw INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.1.18 |
voipCdrStatFilterErrCodeEnableSet 1 to ebable H.248 errcode filter. Set 0 to disable it.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.1.19 |
voipCdrStatResultTable SEQUENCE OF VoipCdrStatResultEntry .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2 |
voipCdrStatResultEntryAn entry of voipCdrStatResultTable. VoipCdrStatResultEntry .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1 |
voipCdrStatResultIndexIndex of record. Index of the newest record will show first.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.1 |
voipCdrStatResultSlotRecord Slotro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.2 |
voipCdrStatResultPortRecord portro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.3 |
voipCdrStatResultTermNameThe termination name used for this record.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.4 |
voipCdrStatResultLineDirection1: Call in
2: Dial outro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.5 |
voipCdrStatResultLocalNumberThe local phone number set by manager and use for localcallro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.6 |
voipCdrStatResultRemoteNumberThe remote phone number which assigned by mgcro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.7 |
voipCdrStatResultOffHookDatetimeIn format YYYYMMDDhhmmssro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.8 |
voipCdrStatResultOnHookDatetimeIn format YYYYMMDDhhmmssro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.9 |
voipCdrStatResultRingStartDatetimeIn format YYYYMMDDhhmmssro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.10 |
voipCdrStatResultRingStopDatetimeIn format YYYYMMDDhhmmssro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.11 |
voipCdrStatResultRtpStartDatetimeIn format YYYYMMDDhhmmssro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.12 |
voipCdrStatResultRtpStopDatetimeIn format YYYYMMDDhhmmssro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.13 |
voipCdrStatResultRtpElapsedTimeIn unit of secondro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.14 |
voipCdrStatResultTxRatereal-time RTP tx packet rate in bpsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.15 |
voipCdrStatResultRxRatereal-time RTP rx packet rate in bpsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.16 |
voipCdrStatResultTxPktCnttotal RTP tx packet counterro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.17 |
voipCdrStatResultRxPktCnttotal RTP rx packet counterro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.18 |
voipCdrStatResultTxFracLostRTP tx packet lost in percentagero INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.19 |
voipCdrStatResultRxFracLostRTP rx packet lost in percentagero INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.20 |
voipCdrStatResultTxJitterTx Jitter in micro-secondro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.21 |
voipCdrStatResultRxJitterRx Jitter in micro-secondro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.22 |
voipCdrStatResultTxAvgDelayAverage tx delay in msro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.23 |
voipCdrStatResultRxAvgDelayAverage rx delay in msro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.24 |
voipCdrStatResultCodeBit map of the call state record.
bit 6(0x20): offhook
bit 5(0x10): remote ringback tone
bit 4(0x08): local ringback tone
bit 3(0x04): dial tone
bit 2(0x02): ring
bit 1(0x01): rtpro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.25 |
voipCdrStatResultErrCodeErrcode of H.248 protocol. 0 mean no error.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.26 |
voipCdrStatResultTerminationCauseTermination Causero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.12.10.2.1.27 |
voipH248Statistics OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.12.11 |
voipH248StatisticsInterfaceInterface id.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.12.11.1 |
voipH248StatisticsMsgSentNumber of sent protocol message, include reset and error.ro Unsigned64 .1.3.6.1.4.1.890.1.5.13.5.13.12.11.2 |
voipH248StatisticsMsgRecvNumber of received message.ro Unsigned64 .1.3.6.1.4.1.890.1.5.13.5.13.12.11.3 |
voipH248StatisticsMsgLostNumber of message without reply.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.12.11.4 |
voipH248StatisticsMsgResentNumber of resent message.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.12.11.5 |
voipH248StatisticsErrorMsgNumber of error message sent.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.12.11.6 |
voipH248StatisticsUnIdentifiedMsgNumber of parse fail message.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.12.11.7 |
enetStats OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.13 |
enetPortStatusTableThe table displays ethernet port status. SEQUENCE OF EnetPortStatusEntry .1.3.6.1.4.1.890.1.5.13.5.13.13.1 |
enetPortStatusEntryAn entry of enetPortStatusTable. EnetPortStatusEntry .1.3.6.1.4.1.890.1.5.13.5.13.13.1.1 |
enetPortStatusLinkUpTypero Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.13.1.1.1 |
enetPortStatusLinkUpTimeThe time since the enet port up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.13.1.1.2 |
enetPortStatusLinkSpeedLink speed in Mbps.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.13.1.1.3 |
enetPortStatusLinkDuplexLink full/half duplex.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.13.1.1.4 |
enetPortStatusDataRateTxTX data rate in kbps.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.13.1.1.5 |
enetPortStatusDataRateRxRX data rate in kbps.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.13.1.1.6 |
enetPortStatusDataUtilTxTX throughput utilization in percentage.ro INTEGER ( 0.. 100 ) .1.3.6.1.4.1.890.1.5.13.5.13.13.1.1.7 |
enetPortStatusDataUtilRxRX throughput utilization in percentage.ro INTEGER ( 0.. 100 ) .1.3.6.1.4.1.890.1.5.13.5.13.13.1.1.8 |
sfpPortStatusTableThe table displays SFP ethernet port status. This table is supported by R5.02 and later versions. SEQUENCE OF SfpPortStatusEntry .1.3.6.1.4.1.890.1.5.13.5.13.13.2 |
sfpPortStatusEntryAn entry of sfpPortStatusTable. SfpPortStatusEntry .1.3.6.1.4.1.890.1.5.13.5.13.13.2.1 |
sfpIdro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.13.2.1.1 |
sfpConnectorro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.13.2.1.2 |
sfpTransceiverro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.13.2.1.3 |
sfpEncodingro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.13.2.1.4 |
sfpNamero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.13.2.1.5 |
sfpPartNumberro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.13.2.1.6 |
sfpRevisionro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.13.2.1.7 |
sfpSerialNumberro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.13.2.1.8 |
sfpTemperaturero Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.13.2.1.9 |
sfpSupplyVoltagero Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.13.2.1.10 |
sfpTxBiasCurrentro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.13.2.1.11 |
sfpTxPowerro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.13.2.1.12 |
sfpRxPowerro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.13.2.1.13 |
ifStats OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.14 |
ifStatusTableThe table displays port interface status. This table is supported by R5.02 and later versions. SEQUENCE OF IfStatusEntry .1.3.6.1.4.1.890.1.5.13.5.13.14.1 |
ifStatusEntryAn entry of ifStatusTable. IfStatusEntry .1.3.6.1.4.1.890.1.5.13.5.13.14.1.1 |
ifInRatero Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.14.1.1.1 |
ifOutRatero Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.14.1.1.2 |
ifCurrentStatusCurrent status of an interfacero Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.14.1.1.3 |
ifUpTimeThe time since the line link up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.14.1.1.4 |
imaStats OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.15 |
imaPvcStatsTableThe table displays IMA Group PVC status. This table is supported by R5.03 and later versions. SEQUENCE OF ImaPvcStatsEntry .1.3.6.1.4.1.890.1.5.13.5.13.15.1 |
imaPvcStatsEntryAn entry of imaPvcStatsTable. ImaPvcStatsEntry .1.3.6.1.4.1.890.1.5.13.5.13.15.1.1 |
imaPvcStatsGroupIndexro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.1.1.1 |
imaPvcStatsVpiro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.1.1.2 |
imaPvcStatsVciro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.1.1.3 |
imaPvcStatsTxPacketsro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.15.1.1.4 |
imaPvcStatsRxPacketsro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.15.1.1.5 |
imaPvcStatsTxUnicastro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.15.1.1.6 |
imaPvcStatsRxUnicastro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.15.1.1.7 |
imaPvcStatsTxMulticastro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.15.1.1.8 |
imaPvcStatsRxMulticastro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.15.1.1.9 |
imaPvcStatsTxBroadcastro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.15.1.1.10 |
imaPvcStatsRxBroadcastro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.15.1.1.11 |
imaPvcStatsTxDiscardro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.15.1.1.12 |
imaPvcStatsRxDiscardro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.15.1.1.13 |
imaGroupStatsTableThe table displays IMA Group status. This table is supported by R5.03 and later versions. SEQUENCE OF ImaGroupStatsEntry .1.3.6.1.4.1.890.1.5.13.5.13.15.2 |
imaGroupStatsEntryAn entry of imaGroupStatsTable. ImaGroupStatsEntry .1.3.6.1.4.1.890.1.5.13.5.13.15.2.1 |
imaGroupStatsGroupIndexro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.2.1.1 |
imaGroupStatsTxCellsTx Cells since resetro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.15.2.1.2 |
imaGroupStatsRxCellsRx Cells since resetro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.15.2.1.3 |
imaGroupStatsTxRateTx data rate in Bytes/sro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.2.1.4 |
imaGroupStatsRxRateRx data rate in Bytes/sro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.2.1.5 |
imaGroupStatsCrcErrCRC errors since resetro Counter64 .1.3.6.1.4.1.890.1.5.13.5.13.15.2.1.6 |
imaGroupCurrDayTableThe table displays IMA Group Current Day Counters. This table is supported by R5.03 and later versions. SEQUENCE OF ImaGroupCurrDayEntry .1.3.6.1.4.1.890.1.5.13.5.13.15.3 |
imaGroupCurrDayEntryAn entry of imaGroupCurrDayTable. ImaGroupCurrDayEntry .1.3.6.1.4.1.890.1.5.13.5.13.15.3.1 |
imaGroupCurrDayGroupIndexro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.3.1.1 |
imaGroupCurrDayUnavailSecsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.3.1.2 |
imaGroupCurrDayNeNumFailuresro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.3.1.3 |
imaGroupCurrDayFeNumFailuresro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.3.1.4 |
imaLinkCurrDayTableThe table displays IMA Link Current Day Counters. This table is supported by R5.03 and later versions. SEQUENCE OF ImaLinkCurrDayEntry .1.3.6.1.4.1.890.1.5.13.5.13.15.4 |
imaLinkCurrDayEntryAn entry of imaLinkCurrDayTable. ImaLinkCurrDayEntry .1.3.6.1.4.1.890.1.5.13.5.13.15.4.1 |
imaLinkCurrDayIfindexro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.4.1.1 |
imaLinkCurrDayImaViolationsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.4.1.2 |
imaLinkCurrDayOifAnomaliesro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.4.1.3 |
imaLinkCurrDayNeSevErroredSecsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.4.1.4 |
imaLinkCurrDayFeSevErroredSecsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.4.1.5 |
imaLinkCurrDayNeUnavailSecsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.4.1.6 |
imaLinkCurrDayFeUnavailSecsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.4.1.7 |
imaLinkCurrDayNeTxUnusableSecsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.4.1.8 |
imaLinkCurrDayNeRxUnusableSecsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.4.1.9 |
imaLinkCurrDayFeTxUnusableSecsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.4.1.10 |
imaLinkCurrDayFeRxUnusableSecsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.4.1.11 |
imaLinkCurrDayNeTxNumFailuresro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.4.1.12 |
imaLinkCurrDayNeRxNumFailuresro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.4.1.13 |
imaLinkCurrDayFeTxNumFailuresro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.4.1.14 |
imaLinkCurrDayFeRxNumFailuresro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.4.1.15 |
imaLinkCurrDayTxStuffsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.4.1.16 |
imaLinkCurrDayRxStuffsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.4.1.17 |
imaGroupConfReadyTableThe table displays IMA Group Configuration Ready status. This table is supported by R5.03 and later versions. SEQUENCE OF ImaGroupConfReadyEntry .1.3.6.1.4.1.890.1.5.13.5.13.15.5 |
imaGroupConfReadyEntryAn entry of imaGroupConfReadyTable. ImaGroupConfReadyEntry .1.3.6.1.4.1.890.1.5.13.5.13.15.5.1 |
imaGroupConfReadyIndexro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.5.1.1 |
imaGroupConfReadyStatero Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.15.5.1.2 |
imaGroupStatusTableThe table displays IMA Group status. This table is supported by R5.03 and later versions. SEQUENCE OF ImaGroupStatusEntry .1.3.6.1.4.1.890.1.5.13.5.13.15.6 |
imaGroupStatusEntryAn entry of imaGroupConfReadyTable. ImaGroupStatusEntry .1.3.6.1.4.1.890.1.5.13.5.13.15.6.1 |
imaGroupStatusGroupIndexro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.6.1.1 |
imaGroupStatusTxPayloadRateMaximum tx data rate in kbpsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.6.1.2 |
imaGroupStatusRxPayloadRateMaximum rx data rate in kbpsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.15.6.1.3 |
e1Stats OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.16 |
e1CurrDayTableThe table displays E1 Port Current Day Counters. This table is supported by R5.03 and later versions. SEQUENCE OF E1CurrDayEntry .1.3.6.1.4.1.890.1.5.13.5.13.16.1 |
e1CurrDayEntryAn entry of e1CurrDayTable. E1CurrDayEntry .1.3.6.1.4.1.890.1.5.13.5.13.16.1.1 |
e1CurrDayIfindexro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.16.1.1.1 |
e1CurrDayLCVsLine Coding Violationro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.16.1.1.2 |
e1CurrDayPCVsPath Coding Violation, a.k.a. Error Blocksro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.16.1.1.3 |
e1CurrDayESsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.16.1.1.4 |
e1CurrDaySESsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.16.1.1.5 |
e1CurrDayUASsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.16.1.1.6 |
e1StatusTableThe table displays E1 Port Status. This table is supported by R5.03 and later versions. SEQUENCE OF E1StatusEntry .1.3.6.1.4.1.890.1.5.13.5.13.16.2 |
e1StatusEntryAn entry of e1StatusTable. E1StatusEntry .1.3.6.1.4.1.890.1.5.13.5.13.16.2.1 |
e1StatusIfindexro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.16.2.1.1 |
e1StatusTxPayloadRateMaximum tx data rate in kbpsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.16.2.1.2 |
e1StatusRxPayloadRateMaximum rx data rate in kbpsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.16.2.1.3 |
e1StatusUpTimeThe uplink time.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.16.2.1.4 |
loopguardStats OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.18 |
loopguardStatsTable SEQUENCE OF LoopguardStatsEntry .1.3.6.1.4.1.890.1.5.13.5.13.18.1 |
loopguardStatsEntryAn entry of loopguardStatsTable. LoopguardStatsEntry .1.3.6.1.4.1.890.1.5.13.5.13.18.1.1 |
loopguardStatsPortro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.18.1.1.1 |
loopguardStatsPortStatusro Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.18.1.1.2 |
loopguardStatsLoopguardStatusro Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.18.1.1.3 |
loopguardStatsTotalTxPacketsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.18.1.1.4 |
loopguardStatsTotalRxPacketsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.18.1.1.5 |
loopguardStatsBadPacketsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.18.1.1.6 |
loopguardStatsShutdownTimesecondsro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.18.1.1.7 |
stpStats OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.19 |
stpPortStatsTableThe table displays STP Port Status. This table is supported by R5.03 and later versions. SEQUENCE OF StpPortStatsEntry .1.3.6.1.4.1.890.1.5.13.5.13.19.1 |
stpPortStatsEntryAn entry of stpPortStatsTable. StpPortStatsEntry .1.3.6.1.4.1.890.1.5.13.5.13.19.1.1 |
stpPortStatusro Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.19.1.1.1 |
stpStatsPortNum OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.19.2 |
stpStatsPortNumForwardingthe number of forwarding ports.
This MIB object is supported by R5.05 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.19.2.1 |
stpStatsPortNumLearningthe number of learning ports.
This MIB object is supported by R5.05 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.19.2.2 |
stpStatsPortNumDiscardingthe number of discarding ports.
This MIB object is supported by R5.05 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.19.2.3 |
stpStatsPortNumDownthe number of link-down ports.
This MIB object is supported by R5.05 and later versions.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.19.2.4 |
gbondStats OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.20 |
gbondStatsTableThe table displays G.Bond Status. This table is supported by R5.05 and later versions. SEQUENCE OF GbondStatsEntry .1.3.6.1.4.1.890.1.5.13.5.13.20.1 |
gbondStatsEntryAn entry of gbondStatsTable. GbondStatsEntry .1.3.6.1.4.1.890.1.5.13.5.13.20.1.1 |
gbondStatsNameAn administratively assigned string, which identifies the bonding group.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.20.1.1.1 |
gbondStatsUpRateThe current up stream rate.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.20.1.1.2 |
gbondStatsDownRateThe current down stream rate.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.20.1.1.3 |
gbondStatsMemberIndicate if the port is a member port of the bonding group. Each bit in the octet specifies a port from MSB to LSB.
for example: 32(hex) = 50(dec) = 00110010(bin) means the port 3, 4 and 7.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.20.1.1.4 |
gbondStatslinkupIndicate if the link status of port is bidirectional. Each bit in the octet specifies a port from MSB to LSB.
for example: 32(hex) = 50(dec) = 00110010(bin) means the port 3, 4 and 7.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.20.1.1.5 |
gbondStatsTxIndicate if the link status of port is Tx only. Each bit in the octet specifies a port from MSB to LSB.
for example: 32(hex) = 50(dec) = 00110010(bin) means the port 3, 4 and 7.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.20.1.1.6 |
gbondStatsRxIndicate if the link status of port is Rx only. Each bit in the octet specifies a port from MSB to LSB.
for example: 32(hex) = 50(dec) = 00110010(bin) means the port 3, 4 and 7.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.20.1.1.7 |
gbondStatslinkdownIndicate if the link status of the port is down. Each bit in the octet specifies a port from MSB to LSB.
for example: 32(hex) = 50(dec) = 00110010(bin) means the port 3, 4 and 7.ro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.20.1.1.8 |
gbondStatsTCModeTransmission Convergence layer.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.13.20.1.1.9 |
gbondStatsTxRateThe tx packet rate.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.20.1.1.10 |
gbondStatsRxRateThe rx packet rate.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.20.1.1.11 |
vdsl2Stats OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.21 |
vdslChanExtendedTableThe table displays VDSL2 channel Status. This table is supported by R5.06 and later versions. SEQUENCE OF VdslChanExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.13.21.1 |
vdslChanExtendedEntryAn entry of vdslChanExtendedTable. VdslChanExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.13.21.1.1 |
vdslChanPrevTxRateUnits: kbpsro Gauge32 .1.3.6.1.4.1.890.1.5.13.5.13.21.1.1.1 |
vdslChanActualRaModeThe actual RA mode.
The possible values are:
fixedRateMode(1) - Fixed rate mode
raInit(2) - Adaptive rate mode at initialization
dynamicRa(3) - Dynamic rate adaptation
sosEnabled(4) - SOS enabledro Xdsl2StatusActualRaMode UNITS "" .1.3.6.1.4.1.890.1.5.13.5.13.21.1.1.2 |
vdslChanRetransmissionModeRTX-USED operational data parameter.
The possible values are:
rtxInUse(1) - RTX in use.
rtxForbidden(2) - RTX not in use because RTX-MODE = FORBIDDEN.
rtxNotSupportedXtuC(3) - RTX not in use because it is not supported by the XTU-C.
rtxNotSupportedXtuR(4) - RTX not in use because it is not supported by the XTU-R.
rtxNotSupportedBoth(5) - RTX not in use because it is not supported by the XTU-C and XTU-R.ro Xdsl2StatusRtxMode UNITS "" .1.3.6.1.4.1.890.1.5.13.5.13.21.1.1.3 |
vdslChanRetransmissionOverheadExpected retransmission overhead in G.inp due to REIN and SHINE noise. Unit is kbps.ro Unsigned32 UNITS "kbps" .1.3.6.1.4.1.890.1.5.13.5.13.21.1.1.4 |
vdslChanGinpFramingTypeThis parameter is equal to zero if G.inp is
not enabled. If G.inp is enabled, it reports
the framing type in use (1, 2, 3, or 4).ro Unsigned32 UNITS "" .1.3.6.1.4.1.890.1.5.13.5.13.21.1.1.5 |
vdslChanActualInpAgainstREINThis parameter reports the actual INP against REIN noise. Unit is 1/2 symbol.ro Unsigned32 UNITS "1/2 symbol" .1.3.6.1.4.1.890.1.5.13.5.13.21.1.1.6 |
vdslChanReedSolomonCodeWordPerDtuThis parameter reports the number of RS codewords per DTU.
It is equal to D when PhyR is enabled.ro Unsigned32 UNITS "" .1.3.6.1.4.1.890.1.5.13.5.13.21.1.1.7 |
vdslPerfDataExtendedTableThe table displays VDSL2 Performance Data. This table is supported by R5.06 and later versions. SEQUENCE OF VdslPerfDataExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.13.21.2 |
vdslPerfDataExtendedEntryAn entry of vdslPerfDataExtendedTable. VdslPerfDataExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.13.21.2.1 |
vdslPerfDataFECsUnits: kbpsro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.2.1.1 |
vdslChanPerfDataExtendedTableThe table displays VDSL2 Channel Performance Data. This table is supported by R5.06 and later versions. SEQUENCE OF VdslChanPerfDataExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.13.21.3 |
vdslChanPerfDataExtendedEntryAn entry of vdslPerfDataExtendedTable. VdslChanPerfDataExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.13.21.3.1 |
vdslChanPerfDataCorrectedBlksCount of all blocks received with errors that were corrected since agent reset.
These blocks are passed on as good data.
Units: blocksro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.3.1.1 |
vdslChanPerfDataUncorrectBlksCount of all blocks received with uncorrectable errors since agent reset.
Units: blocksro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.3.1.2 |
vdslChanPerfDataCodeViolationsCount of CRC-8 (FEBE for xTU-R) anomalies occurring in the
channel during the interval. This parameter is inhibited during
UAS or SES. If the CRC is applied over multiple channels, then
each related CRC-8 (or FEBE) anomaly SHOULD increment each of the
counters related to the individual channels.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.3.1.3 |
xdsl2PMEx OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.21.4 |
xdsl2PMLineEx OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1 |
xdsl2PMLineCurrExtendedTableThe table displays VDSL2 Line Current Performance Data. This table is supported by R5.06 and later versions. SEQUENCE OF Xdsl2PMLineCurrExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1 |
xdsl2PMLineCurrExtendedEntryAn entry of xdsl2PMLineCurrExtendedEntry. Xdsl2PMLineCurrExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1 |
xdsl2PMLCurr15MMonitoredTimeUnits: secondsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.1 |
xdsl2PMLCurr15MLofsCount of the number of Loss of Framing failures since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.2 |
xdsl2PMLCurr15MLolsCount of the number of Loss of Link failures since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.3 |
xdsl2PMLCurr15MLolCount of the number of Loss of Link failures.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.4 |
xdsl2PMLCurr15MLprsCount of the number of Loss of Power failures since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.5 |
xdsl2PMLCurr15MLprCount of the number of Loss of Power failures.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.6 |
xdsl2PMLCurr15MInitsCount of the line initialization attempts since link up. Includes both successful and failed attempts.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.7 |
xdsl2PMLCurr1DayMonitoredTimeUnits: secondsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.8 |
xdsl2PMLCurr1DayLofsCount of the number of Loss of Framing failures since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.9 |
xdsl2PMLCurr1DayLolsCount of the number of Loss of Link failures since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.10 |
xdsl2PMLCurr1DayLolCount of the number of Loss of Link failures.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.11 |
xdsl2PMLCurr1DayLprsCount of the number of Loss of Power failures since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.12 |
xdsl2PMLCurr1DayLprCount of the number of Loss of Power failures.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.13 |
xdsl2PMLCurr1DayInitsCount of the line initialization attempts since link up. Includes both successful and failed attempts.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.14 |
xdsl2PMLSinceLinkInmEqInpThe INM Equivalent Inp histogram since last link up. An
array of 68 octets (each 4 octets means amount of a bin of
histogram), designed for supporting from 1 to 17 bins of
the histogram.
The particular index of the bin incremented by an impulse
noise event is equal to the computed value of equivalent INP,
except the 17th of anomaly INPEQ, which logs all equivalent
INPs greater than 16.
Each bin has a value in the range 0x0 to 0xFFFFFFFFro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.15 |
xdsl2PMLSinceLinkInmIATThe INM Inter Arrival Time histogram since last link up.
An array of 32 octets (each 4 octets means amount of a bin
of histogram), designed for supporting from 0 to 7 bins of
the histogram.
The index of the particular bin incremented by an complete
impulse noise event is determained from the following
INMControl parameters.
Each bin has a value in the range 0x0 to 0xFFFFFFFFro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.16 |
xdsl2PMLSinceLinkInmMEThe INM total measurement since last link up. This
indication occurs every time a data symbol is processed by
the Impulse Noise Sensor.
The range of the value is from 0x0 to 0xFFFFFFFFro Counter32 UNITS "symbols" .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.17 |
xdsl2PMLCurr15MInmEqInpThe INM Equivalent Inp histogram during this 15min
interval. An array of 68 octets (each 4 octets means amount of
a bin of histogram), designed for supporting from 1 to 17 bins
of the histogram.
The particular index of the bin incremented by an impulse
noise event is equal to the computed value of equivalent INP,
except the 17th of anomaly INPEQ, which logs all equivalent
INPs greater than 16.
Each bin has a value in the range 0x0 to 0xFFFFFFFFro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.18 |
xdsl2PMLCurr15MInmIATThe INM Inter Arrival Time histogram during this 15min
interval. An array of 32 octets (each 4 octets means amount of
a bin of histogram), designed for supporting from 0 to 7 bins
of the histogram.
The index of the particular bin incremented by an complete
impulse noise event is determained from the following
INMControl parameters.
Each bin has a value in the range 0x0 to 0xFFFFFFFFro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.19 |
xdsl2PMLCurr15MInmMEThe INM total measurement during this 15min interval.
This indication occurs every time a data symbol is processed
by the Impulse Noise Sensor.
The range of the value is from 0x0 to 0xFFFFFFFFro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.20 |
xdsl2PMLCurr1DayInmEqInpThe INM Equivalent Inp histogram during this 1Day interval.
An array of 68 octets (each 4 octets means amount of a bin of
histogram), designed for supporting from 1 to 17 bins of the
histogram.
The particular index of the bin incremented by an impulse
noise event is equal to the computed value of equivalent INP,
except the 17th of anomaly INPEQ, which logs all equivalent
INPs greater than 16.
Each bin has a value in the range 0x0 to 0xFFFFFFFFro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.21 |
xdsl2PMLCurr1DayInmIATThe INM Inter Arrival Time histogram during this 1Day
interval. An array of 32 octets (each 4 octets means amount of
a bin of histogram), designed for supporting from 0 to 7 bins
of the histogram.
The index of the particular bin incremented by an complete
impulse noise event is determained from the following
INMControl parameters.
Each bin has a value in the range 0x0 to 0xFFFFFFFFro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.22 |
xdsl2PMLCurr1DayInmMEThe INM total measurement during this 1Day interval.
This indication occurs every time a data symbol is processed
by the Impulse Noise Sensor.
The range of the value is from 0x0 to 0xFFFFFFFFro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.23 |
xdsl2PMLSinceInitLofsCount of seconds of Loss of Framing failures since initialized.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.24 |
xdsl2PMLSinceInitLolsCount of seconds of Loss of Link failures since initialized.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.25 |
xdsl2PMLSinceInitLolCount of the number of Loss of Link failures since initialized.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.26 |
xdsl2PMLSinceInitLprsCount of seconds of Loss of Power failures since initialized.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.27 |
xdsl2PMLSinceInitLprCount of the number of Loss of Power failures since initialized.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.28 |
xdsl2PMLSinceInitInitsCount of the line initialization attempts since initialized.
Includes both successful and failed attempts.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.1.1.29 |
xdsl2PMLineHist15MinExtendedTableThe table displays VDSL2 Line History 15 minute Performance Data. This table is supported by R5.06 and later versions. SEQUENCE OF Xdsl2PMLineHist15MinExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.2 |
xdsl2PMLineHist15MinExtendedEntryAn entry of xdsl2PMLineHist15MinExtendedEntry. Xdsl2PMLineHist15MinExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.2.1 |
xdsl2PMLHist15MLofsCount of the number of Loss of Framing failures since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.2.1.1 |
xdsl2PMLHist15MLolsCount of the number of Loss of Link failures since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.2.1.2 |
xdsl2PMLHist15MLolCount of the number of Loss of Link failures.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.2.1.3 |
xdsl2PMLHist15MLprsCount of the number of Loss of Power failures since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.2.1.4 |
xdsl2PMLHist15MLprCount of the number of Loss of Power failures.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.2.1.5 |
xdsl2PMLHist15MInitsCount of the line initialization attempts since link up. Includes both successful and failed attempts.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.2.1.6 |
xdsl2PMLHist15MInmEqInpThe INM Equivalent Inp histogram during 15min interval.
An array of 68 octets (each 4 octets means amount of a bin of
histogram), designed for supporting from 1 to 17 bins of the
histogram.
The particular index of the bin incremented by an impulse
noise event is equal to the computed value of equivalent INP,
except the 17th of anomaly INPEQ, which logs all equivalent
INPs greater than 16.
Each bin has a value in the range 0x0 to 0xFFFFFFFFro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.2.1.7 |
xdsl2PMLHist15MInmIATThe INM Inter Arrival Time histogram during 15min
interval. An array of 32 octets (each 4 octets means amount of
a bin of histogram), designed for supporting from 0 to 7 bins
of the histogram.
The index of the particular bin incremented by an complete
impulse noise event is determained from the following
INMControl parameters.
Each bin has a value in the range 0x0 to 0xFFFFFFFFro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.2.1.8 |
xdsl2PMLHist15MInmMEThe INM total measurement during 15min interval.
This indication occurs every time a data symbol is processed
by the Impulse Noise Sensor.
The range of the value is from 0x0 to 0xFFFFFFFFro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.2.1.9 |
xdsl2PMLineHist1DayExtendedTableThe table displays VDSL2 Line History 1 day Performance Data. This table is supported by R5.06 and later versions. SEQUENCE OF Xdsl2PMLineHist1DayExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.3 |
xdsl2PMLineHist1DayExtendedEntryAn entry of xdsl2PMLineHist1DayExtendedTable. Xdsl2PMLineHist1DayExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.3.1 |
xdsl2PMLHist1DLofsCount of the number of Loss of Framing failures since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.3.1.1 |
xdsl2PMLHist1DLolsCount of the number of Loss of Link failures since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.3.1.2 |
xdsl2PMLHist1DLolCount of the number of Loss of Link failures.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.3.1.3 |
xdsl2PMLHist1DLprsCount of the number of Loss of Power failures since link up.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.3.1.4 |
xdsl2PMLHist1DLprCount of the number of Loss of Power failures.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.3.1.5 |
xdsl2PMLHist1DInitsCount of the line initialization attempts since link up. Includes both successful and failed attempts.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.3.1.6 |
xdsl2PMLHist1DInmEqInpThe INM Equivalent Inp histogram during 1Day interval.
An array of 68 octets (each 4 octets means amount of a bin of
histogram), designed for supporting from 1 to 17 bins of the
histogram.
The particular index of the bin incremented by an impulse
noise event is equal to the computed value of equivalent INP,
except the 17th of anomaly INPEQ, which logs all equivalent
INPs greater than 16.
Each bin has a value in the range 0x0 to 0xFFFFFFFFro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.3.1.7 |
xdsl2PMLHist1DInmIATThe INM Inter Arrival Time histogram during 1Day
interval. An array of 32 octets (each 4 octets means amount of
a bin of histogram), designed for supporting from 0 to 7 bins
of the histogram.
The index of the particular bin incremented by an complete
impulse noise event is determained from the following
INMControl parameters.
Each bin has a value in the range 0x0 to 0xFFFFFFFFro OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.3.1.8 |
xdsl2PMLHist1DInmMEThe INM total measurement during this 1Day interval.
This indication occurs every time a data symbol is processed
by the Impulse Noise Sensor.
The range of the value is from 0x0 to 0xFFFFFFFFro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.1.3.1.9 |
xdsl2PMLineChannelEx OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.21.4.2 |
xdsl2PMChCurrExtendedTableThe table displays VDSL2 Channel Current Performance Data. This table is supported by R5.06 and later versions. SEQUENCE OF Xdsl2PMChCurrExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.13.21.4.2.1 |
xdsl2PMChCurrExtendedEntryAn entry of xdsl2PMChHist15MinExtendedTable. Xdsl2PMChCurrExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.13.21.4.2.1.1 |
xdsl2PMChCurr15MUncorrectBlksCount of all blocks received with uncorrectable errors on this channel within the current 15 minute interval.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.2.1.1.1 |
xdsl2PMChCurr1DayUncorrectBlksCount of all blocks received with uncorrectable errors on this channel within the current 7 day interval.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.2.1.1.2 |
xdsl2PMChSinceLinkRtxNumber of codewords retransmitted since last link up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.2.1.1.3 |
xdsl2PMChCurr15MRtxNumber of codewords retransmitted during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.2.1.1.4 |
xdsl2PMChCurr1DayRtxNumber of codewords retransmitted during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.2.1.1.5 |
xdsl2PMChSinceLinkRtxCorrectedNumber of codewords corrected through retransmission since last link up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.2.1.1.6 |
xdsl2PMChCurr15MRtxCorrectedNumber of codewords corrected through retransmission during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.2.1.1.7 |
xdsl2PMChCurr1DayRtxCorrectedNumber of codewords corrected through retransmission during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.2.1.1.8 |
xdsl2PMChSinceLinkRtxUncorrectedNumber of codewords left uncorrected after retransmission since last link up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.2.1.1.9 |
xdsl2PMChCurr15MRtxUncorrectedNumber of codewords left uncorrected after retransmission during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.2.1.1.10 |
xdsl2PMChCurr1DayRtxUncorrectedNumber of codewords left uncorrected after retransmission during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.2.1.1.11 |
xdsl2PMChSinceLinkLEFTRsLow Error-Free Throughput Rate Seconds since last link up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.2.1.1.12 |
xdsl2PMChCurr15MLEFTRsLow Error-Free Throughput Rate Seconds during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.2.1.1.13 |
xdsl2PMChCurr1DayLEFTRsLow Error-Free Throughput Rate Seconds during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.2.1.1.14 |
xdsl2PMChSinceLinkMinEFTRLowest EFTR observed since last link up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.2.1.1.15 |
xdsl2PMChCurr15MMinEFTRLowest EFTR observed in the current interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.2.1.1.16 |
xdsl2PMChCurr1DayMinEFTRLowest EFTR observed in the current interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.2.1.1.17 |
xdsl2PMChSinceLinkErrFreeBitsThe number of bits belonging to correct DTUs leaving the Rx PMS-TC oo 2(oV16) since last link up.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.2.1.1.18 |
xdsl2PMChCurr15MErrFreeBitsThe number of bits belonging to correct DTUs leaving the Rx PMS-TC oo 2(oV16) during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.2.1.1.19 |
xdsl2PMChCurr1DayErrFreeBitsThe number of bits belonging to correct DTUs leaving the Rx PMS-TC oo 2(oV16) during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.2.1.1.20 |
xdsl2PMChannelEx OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.21.4.3 |
xdsl2PMChHist15MinExtendedTableThe table displays VDSL2 Channel History 15 minute Performance Data. This table is supported by R5.06 and later versions. SEQUENCE OF Xdsl2PMChHist15MinExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.13.21.4.3.1 |
xdsl2PMChHist15MinExtendedEntryAn entry of xdsl2PMChHist15MinExtendedTable. Xdsl2PMChHist15MinExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.13.21.4.3.1.1 |
xdsl2PMChHist15MUncorrectBlksCount of all blocks received with uncorrectable errors on this channel within the history 15 minute interval.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.3.1.1.1 |
xdsl2PMChHist15MRtxNumber of codewords retransmitted during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.3.1.1.2 |
xdsl2PMChHist15MRtxCorrectedNumber of codewords corrected through retransmission during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.3.1.1.3 |
xdsl2PMChHist15MRtxUncorrectedNumber of codewords left uncorrected after retransmission during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.3.1.1.4 |
xdsl2PMChHist15MLEFTRsLow Error-Free Throughput Rate Seconds during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.3.1.1.5 |
xdsl2PMChHist15MMinEFTRLowest EFTR observed in the current interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.3.1.1.6 |
xdsl2PMChHist15MErrFreeBitsThe number of bits belonging to correct DTUs leaving the Rx PMS-TC oo 2(oV16) during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.3.1.1.7 |
xdsl2PMChHist1DExtendedTableThe table displays VDSL2 Channel History 1 day Performance Data. This table is supported by R5.06 and later versions. SEQUENCE OF Xdsl2PMChHist1DExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.13.21.4.3.2 |
xdsl2PMChHist1DExtendedEntryAn entry of xdsl2PMChHist1DExtendedTable. Xdsl2PMChHist1DExtendedEntry .1.3.6.1.4.1.890.1.5.13.5.13.21.4.3.2.1 |
xdsl2PMChHist1DUncorrectBlksCount of all blocks received with uncorrectable errors on this channel within the history 1 day interval.ro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.3.2.1.1 |
xdsl2PMChHist1DayRtxNumber of codewords retransmitted during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.3.2.1.2 |
xdsl2PMChHist1DayRtxCorrectedNumber of codewords corrected through retransmission during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.3.2.1.3 |
xdsl2PMChHist1DayRtxUncorrectedNumber of codewords left uncorrected after retransmission during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.3.2.1.4 |
xdsl2PMChHist1DayLEFTRsLow Error-Free Throughput Rate Seconds during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.3.2.1.5 |
xdsl2PMChHist1DayMinEFTRLowest EFTR observed in the current interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.3.2.1.6 |
xdsl2PMChHist1DayErrFreeBitsThe number of bits belonging to correct DTUs leaving the Rx PMS-TC oo 2(oV16) during this interval.ro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.21.4.3.2.1.7 |
xdsl2LineBandExtTableThis table is supported by R5.06 and later versions. SEQUENCE OF Xdsl2LineBandExtEntry .1.3.6.1.4.1.890.1.5.13.5.13.21.5 |
xdsl2LineBandExtEntryAn entry of xdsl2LineBandExtTable. Xdsl2LineBandExtEntry .1.3.6.1.4.1.890.1.5.13.5.13.21.5.1 |
xdsl2LineBandTxPowerXdsl line band Tx power (in unit of 0.1 Dbm, -1280 indicates that power is empty)ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.21.5.1.1 |
xdsl2LineBandRxPowerXdsl line band Rx power (in unit of 0.1 Dbm, -1280 indicates that power is empty)ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.21.5.1.2 |
mldStats OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.22 |
mldStatsV1QueryInCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.1 |
mldStatsV1ReportInCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.2 |
mldStatsV1DoneInCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.3 |
mldStatsV1QueryInDropCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.4 |
mldStatsV1ReportInDropCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.5 |
mldStatsV1DoneInDropCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.6 |
mldStatsV1QueryOutCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.7 |
mldStatsV1ReportOutCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.8 |
mldStatsV1DoneOutCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.9 |
mldStatsV2QueryInCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.10 |
mldStatsV2ReportInCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.11 |
mldStatsV2QueryInDropCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.12 |
mldStatsV2ReportInDropCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.13 |
mldStatsV2QueryOutCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.14 |
mldStatsV2ReportOutCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.15 |
mldNumOfActiveGroupsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.22.16 |
mldGroupTableThis table is supported by R5.06 and later versions. SEQUENCE OF MldGroupEntry .1.3.6.1.4.1.890.1.5.13.5.13.22.17 |
mldGroupEntryAn entry of mldGroupTable. MldGroupEntry .1.3.6.1.4.1.890.1.5.13.5.13.22.17.1 |
mldGroupVidro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.22.17.1.1 |
mldGroupIpro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.22.17.1.2 |
mldGroupNumOfMembersro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.22.17.1.3 |
mldGroupMemberPortsro PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.22.17.1.4 |
mldGroupNumOfActiveUsersNumber of active users.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.22.17.1.5 |
mldGroupPortTableThis table is supported by R5.06 and later versions. SEQUENCE OF MldGroupPortEntry .1.3.6.1.4.1.890.1.5.13.5.13.22.18 |
mldGroupPortEntryAn entry of mldGroupPortTable. MldGroupPortEntry .1.3.6.1.4.1.890.1.5.13.5.13.22.18.1 |
mldGroupPortVidro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.22.18.1.1 |
mldGroupPortIpro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.22.18.1.2 |
mldGroupPortSourceIpro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.22.18.1.3 |
mldPortCtrlPduTableThis table is supported by R5.06 and later versions. SEQUENCE OF MldPortCtrlPduEntry .1.3.6.1.4.1.890.1.5.13.5.13.22.19 |
mldPortCtrlPduEntryAn entry of mldPortCtrlPduTable. MldPortCtrlPduEntry .1.3.6.1.4.1.890.1.5.13.5.13.22.19.1 |
mldPortCtrlPduQueryCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.19.1.1 |
mldPortCtrlPduReportCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.19.1.2 |
mldPortCtrlPduLeaveCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.19.1.3 |
mldPortNumOfActiveGroupsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.22.19.1.4 |
mldPortCtrlPduV1SuccessJoinCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.19.1.5 |
mldPortCtrlPduV1UnsuccJoinCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.19.1.6 |
mldPortCtrlPduGenQryCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.19.1.7 |
mldPortCtrlPduSpecQryCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.19.1.8 |
mldPortCtrlPduV2SuccessReportCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.19.1.9 |
mldPortCtrlPduV2UnsuccReportCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.19.1.10 |
mldPortCtrlPduInvalidCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.19.1.11 |
mldVlanStatsTableThis table is supported by R5.06 and later versions. SEQUENCE OF MldVlanStatsuEntry .1.3.6.1.4.1.890.1.5.13.5.13.22.20 |
mldVlanStatsuEntryAn entry of mldVlanStatsTable. MldVlanStatsuEntry .1.3.6.1.4.1.890.1.5.13.5.13.22.20.1 |
mldVlanStatsVlanIndexro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.22.20.1.1 |
mldVlanStatsNumOfActiveGroupsro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.22.20.1.2 |
mldVlanStatsQueryPortro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.22.20.1.3 |
mldVlanStatsQuerierIpro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.13.5.13.22.20.1.4 |
mldVlanStatsV1QueryInCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.20.1.5 |
mldVlanStatsV1ReportInCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.20.1.6 |
mldVlanStatsV1DoneInCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.20.1.7 |
mldVlanStatsV1QueryInDropCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.20.1.8 |
mldVlanStatsV1ReportInDropCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.20.1.9 |
mldVlanStatsV1DoneInDropCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.20.1.10 |
mldVlanStatsV1QueryOutCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.20.1.11 |
mldVlanStatsV1ReportOutCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.20.1.12 |
mldVlanStatsV1DoneOutCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.20.1.13 |
mldVlanStatsV2QueryInCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.20.1.14 |
mldVlanStatsV2ReportInCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.20.1.15 |
mldVlanStatsV2QueryInDropCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.20.1.16 |
mldVlanStatsV2ReportInDropCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.20.1.17 |
mldVlanStatsV2QueryOutCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.20.1.18 |
mldVlanStatsV2ReportOutCntro Counter32 .1.3.6.1.4.1.890.1.5.13.5.13.22.20.1.19 |
macFFStats OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.23 |
macFFArpStatusUplinkTable SEQUENCE OF MacFFArpStatusUplinkEntry .1.3.6.1.4.1.890.1.5.13.5.13.23.1 |
macFFArpStatusUplinkEntryThe entry of macFFArpStatusUplinkTable. MacFFArpStatusUplinkEntry .1.3.6.1.4.1.890.1.5.13.5.13.23.1.1 |
macFFArpStatusUplinkIpAddrmacFF arp ip address from uplinkro IpAddress .1.3.6.1.4.1.890.1.5.13.5.13.23.1.1.1 |
macFFArpStatusUplinkMacAddrmacFF arp mac address from uplinkro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.23.1.1.2 |
macFFArpStatusUplinkMacVidmacFF arp vid from uplinkro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.23.1.1.3 |
macFFArpStatusSlotTable SEQUENCE OF MacFFArpStatusSlotEntry .1.3.6.1.4.1.890.1.5.13.5.13.23.2 |
macFFArpStatusSlotEntryThe entry of macFFArpStatusSlotTable. MacFFArpStatusSlotEntry .1.3.6.1.4.1.890.1.5.13.5.13.23.2.1 |
macFFArpStatusSlotIpAddrmacFF arp ip address from subscrib portro IpAddress .1.3.6.1.4.1.890.1.5.13.5.13.23.2.1.1 |
macFFArpStatusSlotMacAddrmacFF arp mac address from subscrib portro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.23.2.1.2 |
macFFArpStatusSlotMacVidmacFF arp vid from subscrib portro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.23.2.1.3 |
macFFArpStatusSlotPortmacFF arp learnt subscrib portro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.23.2.1.4 |
macFFArpCntUplinkTable SEQUENCE OF MacFFArpCntUplinkEntry .1.3.6.1.4.1.890.1.5.13.5.13.23.3 |
macFFArpCntUplinkEntryThe entry of macFFArpCntUplinkTable. MacFFArpCntUplinkEntry .1.3.6.1.4.1.890.1.5.13.5.13.23.3.1 |
macFFArpCntUplinkReqRxmacFF arp request rx counter from uplinkro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.23.3.1.1 |
macFFArpCntUplinkReqTxmacFF arp request tx counter from uplinkro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.23.3.1.2 |
macFFArpCntUplinkReqRxDropmacFF arp request rx drop counter from uplinkro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.23.3.1.3 |
macFFArpCntUplinkRpyRxmacFF arp reply rx counter from uplinkro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.23.3.1.4 |
macFFArpCntUplinkRpyTxmacFF arp reply tx counter from uplinkro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.23.3.1.5 |
macFFArpCntUplinkRpyRxDropmacFF arp reply rx drop counter from uplinkro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.23.3.1.6 |
macFFArpCntPortTable SEQUENCE OF MacFFArpCntPortEntry .1.3.6.1.4.1.890.1.5.13.5.13.23.4 |
macFFArpCntPortEntryThe entry of macFFArpCntPortTable. MacFFArpCntPortEntry .1.3.6.1.4.1.890.1.5.13.5.13.23.4.1 |
macFFArpCntPortReqRxmacFF arp request rx counter from subscrib portro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.23.4.1.1 |
macFFArpCntPortReqTxmacFF arp request tx counter from subscrib portro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.23.4.1.2 |
macFFArpCntPortReqRxDropmacFF arp request rx drop counter from subscrib portro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.23.4.1.3 |
macFFArpCntPortRpyRxmacFF arp reply rx counter from subscrib portro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.23.4.1.4 |
macFFArpCntPortRpyTxmacFF arp reply tx counter from subscrib portro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.23.4.1.5 |
macFFArpCntPortRpyRxDropmacFF reply rx drop counter from subscrib portro Unsigned32 .1.3.6.1.4.1.890.1.5.13.5.13.23.4.1.6 |
imageStats OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.13.24 |
sysBootUpFwIndexro INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.24.1 |
sysBootUpFwVersionro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.24.2 |
sysFlashFwInfoTable SEQUENCE OF SysFlashFwInfoEntry .1.3.6.1.4.1.890.1.5.13.5.13.24.3 |
sysFlashFwInfoEntry SysFlashFwInfoEntry .1.3.6.1.4.1.890.1.5.13.5.13.24.3.1 |
sysFlashFwIndex INTEGER .1.3.6.1.4.1.890.1.5.13.5.13.24.3.1.1 |
sysFlashFwVersionro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.13.24.3.1.2 |
clear OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.14 |
counterClearTargetThis object is supported by R1.02 and later versions.
This managed object is used for identify the target on which
the counter would be cleared. The target is encoded as:
Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7
Byte 2~4: each octet specifies a set of eight slots, with the
first octet specifying slots 1 through 8, and the second
octet specifying slots 9 through 16, and so on.
Byte 5~: each octet specifies a set of eight ports, with the first
octet specifying ports 1 through 8, etc.rw OCTET STRING .1.3.6.1.4.1.890.1.5.13.5.14.1 |
counterClearOpsThis object is supported by R1.02 and later versions.
The corresponding bit is set to 1 to start the operation.
The various bit positions are:
BIT 1: clear interface counters
BIT 2: clear pvc packet counters
BIT 3: clear port ATM counters
BIT 4: clear pvc ATM counters
BIT 5: clear DHCP counters
BIT 6: clear IGMP counters
BIT 7: clear IGMP port counters
BIT 8: clear inband IP interface counters
BIT 9: clear outband IP interface counters
BIT10: clear line performance counters
BIT11: clear performance current counters
BIT12: clear performance current 15min counters
BIT13: clear performance current 1day counters
BIT14: clear macFF arp countersrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.14.2 |
counterClearVpiThis object is supported by R1.02 and later versions.
VPI of the pvc whose counters would be cleared.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.14.3 |
counterClearVciThis object is supported by R1.02 and later versions.
VCI of the pvc whose counters would be cleared.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.14.4 |
imaClear OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.14.5 |
imaClearOpsThis object is supported by R5.03 and later versions.
The corresponding bit is set to 1 to start the operation.
The various bit positions are:
BIT 0: clear pvc pkt counters
BIT 1: clear group cell counters
BIT 2: clear ima group performance current 15min counters
BIT 3: clear ima group performance current 1day counters
BIT 4: clear ima link performance current 15min counters
BIT 5: clear ima link performance current 1day counters
BIT 6: clear e1 performance current 15min counters
BIT 7: clear e1 performance current 1day countersrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.14.5.1 |
imaClearTargetGroupIndexrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.14.5.2 |
imaClearTargetLinkIndex1~8, link index in the grouprw INTEGER .1.3.6.1.4.1.890.1.5.13.5.14.5.3 |
imaClearTargetVpiThis object is supported by R5.03 and later versions.
VPI of the pvc whose counters would be cleared.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.14.5.4 |
imaClearTargetVciThis object is supported by R5.03 and later versions.
VCI of the pvc whose counters would be cleared.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.14.5.5 |
imaClearTargetIfindexThis object is supported by R5.03 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.14.5.6 |
voipClear OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.14.6 |
voipClearOpsThe corresponding bit is set to 1 to start the operation.
The various bit positions are:
BIT 0: clear call detail records
BIT 1: clear H248 statisticsrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.14.6.1 |
voipClearH248TargetInterfaceInterface Idrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.14.6.2 |
cluster OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.15 |
clusterEnableEnable/disable clustering. This object is supported by R3.00 and later versions.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.15.1 |
clusterNameName of the cluster. This object is supported by R3.00 and later versions.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.15.2 |
clusterMemberPasswordPassword of the member. This object is supported by R3.00 and later versions.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.15.3 |
clusterVlanSetting cluster VLAN ID. This object is supported by R3.00 and later versions.rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.15.4 |
clusterCandidate OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.15.5 |
clusterCandidateFlushSetting the object to be 1 to flush the candidate table and re-discover candidates.
This object is supported by R3.00 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.15.5.1 |
clusterCandidateTableA table that contains information about cluster candidates.
This table is supported by R3.00 and later versions. SEQUENCE OF ClusterCandidateEntry .1.3.6.1.4.1.890.1.5.13.5.15.5.2 |
clusterCandidateEntryAn entry of clusterCandidateTable. ClusterCandidateEntry .1.3.6.1.4.1.890.1.5.13.5.15.5.2.1 |
clusterCandidateMacAddrThe MAC address of the candidate.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.15.5.2.1.1 |
clusterCandidateHostNameThe host name of the candidate.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.15.5.2.1.2 |
clusterCandidateModelNameThe model name of the candidate.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.15.5.2.1.3 |
clusterCandidateDeviceTypeThe device type of the candidate.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.15.5.2.1.4 |
clusterMemberConfTableA table that contains configuration about cluster members.
This table is supported by R3.00 and later versions. SEQUENCE OF ClusterMemberConfEntry .1.3.6.1.4.1.890.1.5.13.5.15.6 |
clusterMemberConfEntryAn entry of clusterMemberConfTable. ClusterMemberConfEntry .1.3.6.1.4.1.890.1.5.13.5.15.6.1 |
clusterMemberConfIdThe identity of the entry.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.15.6.1.1 |
clusterMemberConfMacAddrThe MAC address of the member which will join the cluster.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.15.6.1.2 |
clusterMemberConfPasswdThe password of the member which will join the cluster.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.15.6.1.3 |
clusterMemberStatusTableA table that contains information about cluster members.
This table is supported by R3.00 and later versions. SEQUENCE OF ClusterMemberStatusEntry .1.3.6.1.4.1.890.1.5.13.5.15.7 |
clusterMemberStatusEntryAn entry of clusterMemberStatusTable. ClusterMemberStatusEntry .1.3.6.1.4.1.890.1.5.13.5.15.7.1 |
clusterMemberStatusStateThe state of the member.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.15.7.1.1 |
clusterMemberStatusMacAddrThe MAC address of the member.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.15.7.1.2 |
clusterMemberStatusHostNameThe host name of the member.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.15.7.1.3 |
clusterMemberStatusModelNameThe model name of the member.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.15.7.1.4 |
clusterMemberStatusDeviceTypeThe device type of the member.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.15.7.1.5 |
clusterMemberStatusFWVersionThe F/W version of the member.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.15.7.1.6 |
clusterMemberStatusUpTimeThe time since the member joined the cluster.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.890.1.5.13.5.15.7.1.7 |
voip OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.16 |
voipArp OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.16.1 |
voipArpFlushTargetFlush arp entries in the specified slot.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.1.1 |
voipArpFlushOpsSet the object to 1 to start flushing.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.1.2 |
voipArpShowTableDisplay ARP entries learnt in specified slot. SEQUENCE OF VoipArpShowEntry .1.3.6.1.4.1.890.1.5.13.5.16.1.3 |
voipArpShowEntryAn entry of voipArpShowTable. VoipArpShowEntry .1.3.6.1.4.1.890.1.5.13.5.16.1.3.1 |
voipArpShowIpro IpAddress .1.3.6.1.4.1.890.1.5.13.5.16.1.3.1.1 |
voipArpShowMacro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.1.3.1.2 |
voipArpShowTimerro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.1.3.1.3 |
voipSip OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.16.2 |
maxNumOfVoipNumberPlanThe maximum number of VoIP number plan supported by the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.2.1 |
voipNumberPlanTableConfigure numbering plan entry of specified index in specified payphone charging table. SEQUENCE OF VoipNumberPlanEntry .1.3.6.1.4.1.890.1.5.13.5.16.2.2 |
voipNumberPlanEntryAn entry of voipNumberPlanTable. VoipNumberPlanEntry .1.3.6.1.4.1.890.1.5.13.5.16.2.2.1 |
voipNumberPlanNameNumbering plan table name.ro DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.2.2.1.1 |
voipNumberPlanIndexro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.2.2.1.2 |
voipNumberPlanPatternup to 47 characters, allow digit, '*', and '#' characters and
meaning characters that include 'x', '.', '|' and range format
characters that include '~', ',' and parenthesis '(', ')'
and brackets '[', ']' and at most one parenthesis pair and
'T' for terminate are allowed and two quotation marks
means a null pattern for hot dial,
examples: '002(x.)', '0(x.)', and '(x.)'rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.2.2.1.3 |
voipNumberPlanRuleAllowed characters are 0~9, and '\c' stand for country code,
'\d' stand for national destination code,
'\1' stand for matched string enclosed by the parenthesis pair,
and 'deny' stand for the pattern specified is not allowed and
<tel> accept 1-15 digits includes '+', '*' and '#' for hot or
speed dial application.
Examples: '\1', '\c\1', and '\c\d\1'.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.2.2.1.4 |
voipNumberPlanRowStatusThis object is used to create a new entry or delete an existing entry in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.2.2.1.5 |
maxNumOfVoipDialPlanThe maximum number of VoIP dial plan supported by the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.2.3 |
voipDialPlanTableConfigure dial plan related configuration.
This table is supported by R5.01 and later versions. SEQUENCE OF VoipDialPlanEntry .1.3.6.1.4.1.890.1.5.13.5.16.2.4 |
voipDialPlanEntryAn entry of voipDialPlanTable. VoipDialPlanEntry .1.3.6.1.4.1.890.1.5.13.5.16.2.4.1 |
voipDialPlanNameDial plan table name.ro DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.2.4.1.1 |
voipDialPlanPatternonly 63 DTMF characters that include digits, '*', '#' and meaning characters that
include 'x', '.', '|' and characters of range format that include '~', ',' and
brackets ('[', ']') are allowed.
Note:
'x' represents any digit character
'.' represents one or more repetitions of character or range that precedes it,
can't use in brackets
'!' represents the user-dialed number can be rejected by placing '!' at the end of the pattern
'|' to connect next sub-pattern
'[' and ']' must pair and nest brackets is illegal
'~' and ',' only show in brackets
'~' connected characters must be digit
User should make sure to create unique pattern for each SIP proxy server.
The VOP1248G-61 is not able to distinguish between dial plan tables if they
have the same pattern.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.2.4.1.2 |
voipDialPlanNumOfPrefixCutThe number of digits at the beginning of the dialed number that will be removed.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.2.4.1.3 |
voipDialPlanSipServerSIP profile name.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.2.4.1.4 |
voipDialPlanPrefixAddDigitsOnly digit characters are allowed or use two quotation mark to
indicate no prefix added digits.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.2.4.1.5 |
voipDialPlanNumberOfInterdigitThe number of dialing digits.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.2.4.1.6 |
voipDialPlanInterdigitTimeoutInter-digit timeout in seconds.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.2.4.1.7 |
voipDialPlanRowStatusThis object is used to create a new entry or delete an existing entry in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.2.4.1.8 |
maxNumOfVoipKeyPatternThe maximum number of VoIP key patterns supported by the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.2.5 |
voipKeyPatternTableConfigure key pattern related configuration.
This table is supported by R5.01 and later versions. SEQUENCE OF VoipKeyPatternEntry .1.3.6.1.4.1.890.1.5.13.5.16.2.6 |
voipKeyPatternEntryAn entry of voipKeyPatternTable. VoipKeyPatternEntry .1.3.6.1.4.1.890.1.5.13.5.16.2.6.1 |
voipKeyPatternNameKey pattern table name.ro DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.2.6.1.1 |
voipKeyPatternServiceTypero Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.2.6.1.2 |
voipKeyPatternPatternAllowed characters are 0~9, *, and #.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.2.6.1.3 |
voipKeyPatternRowStatusThis object is used to create a new entry or delete an existing entry in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.2.6.1.4 |
voipLocalCall OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.16.2.7 |
voipLocalCallSyncSet the object to 1 to synchronize msc local call file with SIP linecard.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.2.7.1 |
voipLocalCallEnterTimerw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.2.7.2 |
voipLocalCallExitTimerw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.2.7.3 |
maxNumOfVoipLocalHelpThe maximum number of VoIP local help entries supported by the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.2.8 |
voipLocalHelpTableConfigure telephone number of specified index in specified local help table.
This table is supported by R5.01 and later versions. SEQUENCE OF VoipLocalHelpEntry .1.3.6.1.4.1.890.1.5.13.5.16.2.9 |
voipLocalHelpEntryAn entry of voipLocalHelpTable. VoipLocalHelpEntry .1.3.6.1.4.1.890.1.5.13.5.16.2.9.1 |
voipLocalHelpNameLocal help table name.ro DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.2.9.1.1 |
voipLocalHelpIndexIndex number.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.2.9.1.2 |
voipLocalHelpTelNumberOnly digits are allowed.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.2.9.1.3 |
voipLocalHelpRowStatusThis object is used to create a new entry or delete an existing entry in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.2.9.1.4 |
voipIpSetTableConfigure IP address and VLAN ID of specified slot. SEQUENCE OF VoipIpSetEntry .1.3.6.1.4.1.890.1.5.13.5.16.3 |
voipIpSetEntryAn entry of voipIpSetTable. VoipIpSetEntry .1.3.6.1.4.1.890.1.5.13.5.16.3.1 |
voipIpSetIpIP address.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.16.3.1.1 |
voipIpSetVidrw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.16.3.1.2 |
voipIpSetMaskNetwork mask.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.3.1.3 |
voipDnsTableConfigure DNS server IP of specified slot. SEQUENCE OF VoipDnsEntry .1.3.6.1.4.1.890.1.5.13.5.16.4 |
voipDnsEntryAn entry of voipDnsTable. VoipDnsEntry .1.3.6.1.4.1.890.1.5.13.5.16.4.1 |
voipDnsIpIP address.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.16.4.1.1 |
maxNumOfVoipRouteThe maximum number of VoIP routing entries in a slot.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.7 |
voipRouteTable SEQUENCE OF VoipRouteEntry .1.3.6.1.4.1.890.1.5.13.5.16.8 |
voipRouteEntryAn entry of voipRouteTable. VoipRouteEntry .1.3.6.1.4.1.890.1.5.13.5.16.8.1 |
voipRouteSlotSpecified slot number.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.8.1.1 |
voipRouteIpIP address.ro IpAddress .1.3.6.1.4.1.890.1.5.13.5.16.8.1.2 |
voipRouteGatewayGateway IP.ro IpAddress .1.3.6.1.4.1.890.1.5.13.5.16.8.1.3 |
voipRouteMaskNetwork mask.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.8.1.4 |
voipRouteMetricMetric number of the route.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.8.1.5 |
voipRouteRowStatusThis object is used to create a new entry or delete an existing entry in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.8.1.6 |
voipCountryCodeConfigure country code (information) for VoIP services.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.9 |
voipH248 OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.16.10 |
voipH248MgConfTableThis table is used to create MG instance at specified slot with specified MGC profile.
This table is supported by R5.01 and later versions. SEQUENCE OF VoipH248MgConfEntry .1.3.6.1.4.1.890.1.5.13.5.16.10.1 |
voipH248MgConfEntryAn entry in voipH248MgConfTable. VoipH248MgConfEntry .1.3.6.1.4.1.890.1.5.13.5.16.10.1.1 |
voipH248MgConfSlotLine card slot number.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.10.1.1.1 |
voipH248MgConfNameMG name.ro DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.10.1.1.2 |
voipH248MgConfEnableEnable/disable MG.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.10.1.1.3 |
voipH248MgConfH248ProfileH.248 profile name.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.10.1.1.4 |
voipH248MgConfPortMG port number.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.10.1.1.5 |
voipH248MgConfRowStatusThis object is used to create a new row or delete an existing row in this table..rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.10.1.1.6 |
voipH248InterfaceConfTable SEQUENCE OF VoipH248InterfaceConfEntry .1.3.6.1.4.1.890.1.5.13.5.16.10.2 |
voipH248InterfaceConfEntryAn entry in voipH248InterfaceConfTable. VoipH248InterfaceConfEntry .1.3.6.1.4.1.890.1.5.13.5.16.10.2.1 |
voipH248InterfaceConfIdLine card slot number.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.10.2.1.1 |
voipH248InterfaceConfMgNameMG name.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.10.2.1.2 |
voipH248InterfaceConfMgEnableEnable/disable MG.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.10.2.1.3 |
voipH248InterfaceConfH248ProfileH.248 profile name.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.10.2.1.4 |
voipH248InterfaceConfPortMG port number.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.10.2.1.5 |
voipH248InterfaceConfIpInterface Iprw IpAddress .1.3.6.1.4.1.890.1.5.13.5.16.10.2.1.6 |
voipH248InterfaceConfMasklennetwork mask, 0~32rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.10.2.1.7 |
voipH248InterfaceConfVid1~4094rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.16.10.2.1.8 |
voipH248InterfaceConfPrimaryslot idrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.10.2.1.9 |
voipH248InterfaceConfSecondaryslot idrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.10.2.1.10 |
voipH248InterfaceConfBhcaPeakpeak call attempt allowance in one second , 0~30rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.10.2.1.11 |
voipH248InterfaceConfBhcaAverageaverage call attempt allowance in one hour, 0~60000rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.10.2.1.12 |
voipH248SlotConfTable SEQUENCE OF VoipH248SlotConfEntry .1.3.6.1.4.1.890.1.5.13.5.16.10.3 |
voipH248SlotConfEntryAn entry in voipH248ConfSlotTable. VoipH248SlotConfEntry .1.3.6.1.4.1.890.1.5.13.5.16.10.3.1 |
voipH248SlotConfIdLine card slot number.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.10.3.1.1 |
voipH248SlotConfMasterIp1Master Iprw IpAddress .1.3.6.1.4.1.890.1.5.13.5.16.10.3.1.2 |
voipH248SlotConfMasterIp2Master Iprw IpAddress .1.3.6.1.4.1.890.1.5.13.5.16.10.3.1.3 |
voipH248SlotConfOpmodeOpmoderw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.10.3.1.4 |
voipH248SlotConf8021pPrio802.1p bit for H.248 internal message packet, 0 ~ 7rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.10.3.1.5 |
voipH248SlotConfPriorityDscpDSCP for H.248 internal message packet, 0 ~ 63rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.10.3.1.6 |
voipH248SlaveConfTable SEQUENCE OF VoipH248SlaveConfEntry .1.3.6.1.4.1.890.1.5.13.5.16.10.4 |
voipH248SlaveConfEntryAn entry in voipH248InterfaceSlaveTable. VoipH248SlaveConfEntry .1.3.6.1.4.1.890.1.5.13.5.16.10.4.1 |
voipH248SlaveConfInterfaceIdLine card slot number.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.10.4.1.1 |
voipH248SlaveConfSlaveIdSlave Memberrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.10.4.1.2 |
voipH248SlaveConfSlaveIpSlave Iprw IpAddress .1.3.6.1.4.1.890.1.5.13.5.16.10.4.1.3 |
voipH248Localcall OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.16.10.5 |
voipH248LocalcallEnterTimeThe time to enter localcall utility after MGC missing.
1~60, in unit of minutesrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.10.5.1 |
voipH248LocalcallExistTimeThe time to exist localcall utility after MGC reconnected.
1~60, in unit of minutesrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.10.5.2 |
voipCountryCodeParam OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.16.11 |
lawro Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.11.1 |
impedancero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.11.2 |
loopCurrentro INTEGER UNITS "mA" .1.3.6.1.4.1.890.1.5.13.5.16.11.3 |
taxTypero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.11.4 |
ringFrequencyro INTEGER UNITS "Hz" .1.3.6.1.4.1.890.1.5.13.5.16.11.5 |
ringAmplitudero INTEGER UNITS "Vrms" .1.3.6.1.4.1.890.1.5.13.5.16.11.6 |
ringOnTime1ro INTEGER UNITS "miniseconds" .1.3.6.1.4.1.890.1.5.13.5.16.11.7 |
ringOffTime1ro INTEGER UNITS "miniseconds" .1.3.6.1.4.1.890.1.5.13.5.16.11.8 |
ringOnTime2ro INTEGER UNITS "miniseconds" .1.3.6.1.4.1.890.1.5.13.5.16.11.9 |
ringOffTime2ro INTEGER UNITS "miniseconds" .1.3.6.1.4.1.890.1.5.13.5.16.11.10 |
flashMinro INTEGER UNITS "miniseconds" .1.3.6.1.4.1.890.1.5.13.5.16.11.11 |
flashMaxro INTEGER UNITS "miniseconds" .1.3.6.1.4.1.890.1.5.13.5.16.11.12 |
breakMinro INTEGER UNITS "miniseconds" .1.3.6.1.4.1.890.1.5.13.5.16.11.13 |
breakMaxro INTEGER UNITS "miniseconds" .1.3.6.1.4.1.890.1.5.13.5.16.11.14 |
makeMinro INTEGER UNITS "miniseconds" .1.3.6.1.4.1.890.1.5.13.5.16.11.15 |
makeMaxro INTEGER UNITS "miniseconds" .1.3.6.1.4.1.890.1.5.13.5.16.11.16 |
interDigitMinro INTEGER UNITS "miniseconds" .1.3.6.1.4.1.890.1.5.13.5.16.11.17 |
meterFrequencyro INTEGER UNITS "kHz" .1.3.6.1.4.1.890.1.5.13.5.16.11.18 |
meterOnTimero INTEGER UNITS "miniseconds" .1.3.6.1.4.1.890.1.5.13.5.16.11.19 |
meterOffTimero INTEGER UNITS "miniseconds" .1.3.6.1.4.1.890.1.5.13.5.16.11.20 |
cidTypero Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.11.21 |
payloadTypero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.11.22 |
firstTASTypero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.11.23 |
secondTASTypero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.11.24 |
firstTASIntervalro INTEGER UNITS "miniseconds" .1.3.6.1.4.1.890.1.5.13.5.16.11.25 |
secondTASIntervalro INTEGER UNITS "miniseconds" .1.3.6.1.4.1.890.1.5.13.5.16.11.26 |
startToRingro INTEGER UNITS "miniseconds" .1.3.6.1.4.1.890.1.5.13.5.16.11.27 |
dialTonero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.11.28 |
ringBackTonero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.11.29 |
busyTonero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.11.30 |
congestionTonero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.11.31 |
callWaitingTone1ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.11.32 |
callWaitingTone2ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.11.33 |
specialDialTonero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.11.34 |
howlerTonero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.11.35 |
warningTonero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.11.36 |
confirmationTonero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.11.37 |
holdingTonero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.11.38 |
numberUnobtainableToneThis object is supported by R5.05 and later versions.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.11.39 |
recallDialTonero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.11.40 |
specialInformationTonero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.11.41 |
voipPots OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.16.12 |
voipPotsRingTableThis table is supported by R5.05 and later versions. SEQUENCE OF VoipPotsRingEntry .1.3.6.1.4.1.890.1.5.13.5.16.12.1 |
voipPotsRingEntryAn entry in voipPotsRingEntry. VoipPotsRingEntry .1.3.6.1.4.1.890.1.5.13.5.16.12.1.1 |
voipPotsRingConfIdindexro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.12.1.1.1 |
voipPotsRingConfNameDefvalConfigure pots ring name to use default value.
1 : enable
2 : disablerw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.12.1.1.2 |
voipPotsRingConfNamenamerw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.12.1.1.3 |
voipPotsRingConfPatternDefvalConfigure pots ring pattern to use default value.
1 : enable
2 : disablerw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.12.1.1.4 |
voipPotsRingConfPatternOn1first on timerw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.12.1.1.5 |
voipPotsRingConfPatternOff1first off timerw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.12.1.1.6 |
voipPotsRingConfPatternOn2second on timerw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.12.1.1.7 |
voipPotsRingConfPatternOff2second off timerw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.12.1.1.8 |
voipPotsRingConfPatternOn3third on timerw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.12.1.1.9 |
voipPotsRingConfPatternOff3third off timerw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.12.1.1.10 |
voipPotsFlash OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.16.12.2 |
voipPotsFlashDefvalConfigure pots flash to use default setting.
1 : enable
2 : disablerw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.12.2.1 |
voipPotsFlashMinTimeMinimum time of hook-flash detection period.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.12.2.2 |
voipPotsFlashMaxTimeMaximum time of hook-flash detection period.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.12.2.3 |
voipPotsRingVoltageThe ring output voltage of pots
25~90, in unit of Vrms.
0 means set to default value.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.12.3 |
voipIfindexMap OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.16.13 |
voipInterfaceMapTableA list of interface entries map voip interface indexes to interface indexes. SEQUENCE OF VoipInterfaceMapEntry .1.3.6.1.4.1.890.1.5.13.5.16.13.1 |
voipInterfaceMapEntryAn entry in voipInterfaceMapTable. VoipInterfaceMapEntry .1.3.6.1.4.1.890.1.5.13.5.16.13.1.1 |
voipIfIndexvoip index interface InterfaceIndex (IF-MIB) .1.3.6.1.4.1.890.1.5.13.5.16.13.1.1.1 |
ifIndexValueMapped interface index value for a voip interface index.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.890.1.5.13.5.16.13.1.1.2 |
voipIfTableA list of interface entries map interface indexes to voip interface indexes. SEQUENCE OF VoipIfEntry .1.3.6.1.4.1.890.1.5.13.5.16.13.2 |
voipIfEntryAn entry in voipData2PotsIndexMapEntry. VoipIfEntry .1.3.6.1.4.1.890.1.5.13.5.16.13.2.1 |
voipIfIndexValueMapped voip interface index value for a interface index.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.890.1.5.13.5.16.13.2.1.1 |
voipSingleIp OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.16.14 |
voipExtH248 OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.16.14.1 |
voipExtH248InterfaceConf OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.16.14.1.1 |
voipExtH248InterfaceConfMgNameMG name.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.14.1.1.1 |
voipExtH248InterfaceConfMgEnableEnable/disable MG.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.1.1.2 |
voipExtH248InterfaceConfH248ProfileH.248 profile name.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.14.1.1.3 |
voipExtH248InterfaceConfPortMG port number.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.1.1.4 |
voipExtH248InterfaceConfSignalIpSignaling Iprw IpAddress .1.3.6.1.4.1.890.1.5.13.5.16.14.1.1.5 |
voipExtH248InterfaceConfSignalMasklenSignaling network mask, 0~32rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.1.1.6 |
voipExtH248InterfaceConfSignalVid1~4094rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.16.14.1.1.7 |
voipExtH248InterfaceConfMediaIpMedia Iprw IpAddress .1.3.6.1.4.1.890.1.5.13.5.16.14.1.1.8 |
voipExtH248InterfaceConfMediaMasklenMedia network mask, 0~32rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.1.1.9 |
voipExtH248InterfaceConfMediaVid1~4094rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.16.14.1.1.10 |
voipExtH248InterfaceConfDnsIpDNS Iprw IpAddress .1.3.6.1.4.1.890.1.5.13.5.16.14.1.1.11 |
voipExtH248InterfaceConfRegisterRetryRegister retry time interval, in unit of minute. range is 1 to 1440.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.1.1.12 |
voipExtH248InterfaceMaxNumOfVoipRoutero INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.1.2 |
voipExtH248InterfaceRouteTable SEQUENCE OF VoipExtH248InterfaceRouteEntry .1.3.6.1.4.1.890.1.5.13.5.16.14.1.3 |
voipExtH248InterfaceRouteEntryAn entry of voipExtH248InterfaceRouteTable. VoipExtH248InterfaceRouteEntry .1.3.6.1.4.1.890.1.5.13.5.16.14.1.3.1 |
voipExtH248InterfaceRouteIpIP address.ro IpAddress .1.3.6.1.4.1.890.1.5.13.5.16.14.1.3.1.1 |
voipExtH248InterfaceRouteGatewayGateway IP.ro IpAddress .1.3.6.1.4.1.890.1.5.13.5.16.14.1.3.1.2 |
voipExtH248InterfaceRouteMaskNetwork mask.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.1.3.1.3 |
voipExtH248InterfaceRouteMetricMetric number of the route.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.1.3.1.4 |
voipExtH248InterfaceRouteRowStatusThis object is used to create a new entry or delete an existing entry in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.14.1.3.1.5 |
voipExtStats OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.16.14.2 |
voipExtH248InterfaceStat OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.16.14.2.1 |
voipExtH248InterfaceStatMgStateMg Statero Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.2.1.1 |
voipExtH248InterfaceStatPrimaryProtectionStatePrimary Protection Statero Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.2.1.2 |
voipExtH248InterfaceStatSecondaryProtectionStateSecondary Protection Statero Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.2.1.3 |
voipExtH248InterfaceStatRedundantStateRedundant Statero Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.2.1.4 |
voipExtH248InterfaceStatMgcIpMGC IP address.ro IpAddress .1.3.6.1.4.1.890.1.5.13.5.16.14.2.1.5 |
voipExtH248InterfaceStatMgH248MacThe MAC used by megaco packets.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.14.2.1.6 |
voipExtH248InterfaceStatLocalcallStatLocal call state.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.2.1.7 |
voipExtH248MediaStatTable SEQUENCE OF VoipExtH248MediaStatEntry .1.3.6.1.4.1.890.1.5.13.5.16.14.2.2 |
voipExtH248MediaStatEntryAn entry of voipExtH248MediaStatTable. VoipExtH248MediaStatEntry .1.3.6.1.4.1.890.1.5.13.5.16.14.2.2.1 |
voipExtH248MediaStatSlotIdSlot IDro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.2.2.1.1 |
voipExtH248MediaStatPortCountport countro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.2.2.1.2 |
voipExtH248MediaStatStatestatero Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.2.2.1.3 |
voipExtH248TerminationStatTable SEQUENCE OF VoipExtH248TerminationStatEntry .1.3.6.1.4.1.890.1.5.13.5.16.14.2.3 |
voipExtH248TerminationStatEntryAn entry of voipExtH248TerminationStatStateTable. VoipExtH248TerminationStatEntry .1.3.6.1.4.1.890.1.5.13.5.16.14.2.3.1 |
voipExtH248TerminationStatStateSlotIdMedia Card Id of the termination.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.2.3.1.1 |
voipExtH248TerminationStatStatePortNumberPort number the termination.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.2.3.1.2 |
voipExtH248TerminationStatNameTermination Name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.14.2.3.1.3 |
voipExtH248TerminationStatPhoneStatePhone Statero Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.2.3.1.4 |
voipExtH248TerminationStatCallServiceStateCall Service Statero Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.2.3.1.5 |
voipExtH248TerminationStatQuery OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.16.14.2.4 |
voipExtH248TerminationStatQueryTerminationNameTermination Namerw DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.14.2.4.1 |
voipExtH248TerminationStatQuerySlotIdSlot Idro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.2.4.2 |
voipExtH248TerminationStatQueryPortNumberPort Numberro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.2.4.3 |
voipExtH248TerminationStatQueryPhoneStatePhone Statero Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.2.4.4 |
voipExtH248TerminationStatQueryCallServiceStateCallService Statero Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.2.4.5 |
voipExtSipProfile OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.16.14.3 |
voipExtMaxNumOfSipProfilesThe maximum number of SIP profiles supported by the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.3.1 |
voipExtSipProfileTableThis table includes SIP protocol related configuration.
This table is supported by R4.01 and later versions. SEQUENCE OF VoipExtSipProfileEntry .1.3.6.1.4.1.890.1.5.13.5.16.14.3.2 |
voipExtSipProfileEntryAn entry in voipExtSipProfileTable. VoipExtSipProfileEntry .1.3.6.1.4.1.890.1.5.13.5.16.14.3.2.1 |
voipExtSipProfileNameThis object is used by the SIP profile table in order to identify a row of this table.ro DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.14.3.2.1.1 |
voipExtSipProfileSipSvrIP used for SIP registration or SIP domain name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.14.3.2.1.2 |
voipExtSipProfileRegSvrRegistration server IP or registration server domain name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.14.3.2.1.3 |
voipExtSipProfileProxySvrProxy server IP or proxy server doamin name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.14.3.2.1.4 |
voipExtSipProfileSipPortSIP UA port number.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.3.2.1.5 |
voipExtSipProfileRegSvrPortRegistration server port number.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.3.2.1.6 |
voipExtSipProfileProxySvrPortProxy server port number.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.3.2.1.7 |
voipExtSipProfilePbit802.1p bit for SIP and RTP packet.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.3.2.1.8 |
voipExtSipProfileDscpDSCP for SIP and RTP packet.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.3.2.1.9 |
voipExtSipProfileKeepAliverw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.3.2.1.10 |
voipExtSipProfilePrackrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.3.2.1.11 |
voipExtSipProfileSeSession expiration time in seconds.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.3.2.1.12 |
voipExtSipProfileSwitchTypeSwitch typerw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.3.2.1.13 |
voipExtSipProfileRtpStartPortstart of RTP port number. This MIB object is supported by R5.05 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.3.2.1.14 |
voipExtSipProfileRtpEndPortend of RTP port number. This MIB object is supported by R5.05 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.3.2.1.15 |
voipExtSipProfileRegistrationExpirerw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.3.2.1.16 |
voipExtSipProfileRegistrationExpireTimeregistration expiration time under registered state, 120~65535 secondsrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.3.2.1.17 |
voipExtSipProfileRegistrationRetryTimeregistration retry time under un-registered state, 120~900 secondsrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.3.2.1.18 |
voipExtSipProfileRowStatusThis object is used to create a new row or delete an existing row in the table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.14.3.2.1.19 |
voipExtSipProfilePrefixAddDigitsThe prefix digits add before tel numberro DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.14.3.2.1.20 |
voipExtMaxNumOfSipCallSvcProfilesThe maximum number of SIP call service profiles supported by the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.3.3 |
voipExtSipCallSvcProfileTableThis table includes SIP call service related configuration.
This table is supported by R4.01 and later versions. SEQUENCE OF VoipExtSipCallSvcProfileEntry .1.3.6.1.4.1.890.1.5.13.5.16.14.3.4 |
voipExtSipCallSvcProfileEntryAn entry in sipCallSvcProfileTable. VoipExtSipCallSvcProfileEntry .1.3.6.1.4.1.890.1.5.13.5.16.14.3.4.1 |
voipExtSipCallSvcProfileNameThis object is used by the SIP call service profile table in order to identify a row of this table.ro DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.14.3.4.1.1 |
voipExtSipCallSvcProfileKeypatternKey pattern table name. This object is supported by R5.01 and later versions.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.14.3.4.1.2 |
voipExtSipCallSvcProfileDialPlanOnPlease set CC, NDC, and dialplan table first.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.3.4.1.3 |
voipExtSipCallSvcProfileDialPlanCcCountry code, only digit 0..9 are allowed.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.14.3.4.1.4 |
voipExtSipCallSvcProfileDialPlanNdcNational destination code, only digit 0..9 are allowed.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.14.3.4.1.5 |
voipExtSipCallSvcProfileDialPlanTableNumbering plan table name.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.14.3.4.1.6 |
voipExtSipCallSvcProfileDndOnDo not Distrurb.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.3.4.1.7 |
voipExtSipCallSvcProfileDtmfdtmf bypass : bypass DTMF tone
dtmf rfc2833 : DTMF tone relay according to RFC2833
dtmf rfc2833like : DTMF tone relay by SIP INFO message, but RFC2833 payload
dtmf sipinfo : DTMF tone relay by SIP INFO signal message
dtmf plaintext : DTMF tone relay by SIP INFO plain text messagerw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.3.4.1.8 |
voipExtSipCallSvcProfileDtmfRfc2833Payloaddtmf rfc2833 payload type, 96~100rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.3.4.1.9 |
voipExtSipCallSvcProfileCallWaitOnrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.3.4.1.11 |
voipExtSipCallSvcProfileClipOnrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.3.4.1.12 |
voipExtSipCallSvcProfileClirOnrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.3.4.1.13 |
voipExtSipCallSvcProfileCallTransferOnrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.3.4.1.14 |
voipExtSipCallSvcProfileCallConferenceOnrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.3.4.1.15 |
voipExtSipCallSvcProfileFaxfax g711 : FAX service pass through by ITU-T G.711
fax t38 : FAX service by ITU-T T.38 UDPrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.3.4.1.16 |
voipExtSipCallSvcProfileFirstDigitfirst digit timeout. This MIB object is supported by R5.05 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.3.4.1.17 |
voipExtSipCallSvcProfileInterdigitinter digit timeout. This MIB object is supported by R5.05 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.3.4.1.18 |
voipExtSipCallSvcProfileMatchdigitmatch digit timeout. This MIB object is supported by R5.05 and later versions.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.3.4.1.19 |
voipExtSipCallSvcProfileFlashflash invite : send SIP INVITE message
flash rfc2833 : flash relay according to RFC2833
flash rfc2833like : flash relay by SIP INFO message, but RFC2833 payload
flash sipinfo1 : flash relay by SIP INFO signal=16 message
flash sipinfo2 : flash relay by SIP INFO signal=hf message
flash sipinfo3 : flash relay by SIP INFO signal=hook-flash message
flash sipinfo4 : flash relay by SIP INFO plain text message
flash sipinfo5 : flash relay by multiple SIP INFO signal messages and
signal content come from specified pattern string
flash sipinfo6 : flash relay by SIP INFO specified information message
skip : no flash event, only onhook and offhookrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.3.4.1.20 |
voipExtSipCallSvcProfileFlashPatternrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.14.3.4.1.21 |
voipExtSipCallSvcProfileLocalCallOnrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.3.4.1.22 |
voipExtSipCallSvcProfileMWIOnrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.3.4.1.23 |
voipExtSipCallSvcProfileCentrexOnrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.3.4.1.24 |
voipExtSipCallSvcProfileRowStatusThis object is used to create a new row or delete an existing row in the table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.14.3.4.1.25 |
voipExtSipCallSvcProfileLocalHelpTableThis table is supported by R5.01 and later versions. SEQUENCE OF VoipExtSipCallSvcProfileLocalHelpEntry .1.3.6.1.4.1.890.1.5.13.5.16.14.3.5 |
voipExtSipCallSvcProfileLocalHelpEntryAn entry in sipCallSvcProfileLocalHelpTable. VoipExtSipCallSvcProfileLocalHelpEntry .1.3.6.1.4.1.890.1.5.13.5.16.14.3.5.1 |
voipExtSipCallSvcProfileLocalHelpIndexIndex number.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.3.5.1.1 |
voipExtSipCallSvcProfileLocalHelpTableNameLocal help table name.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.14.3.5.1.2 |
voipExtSipCallSvcProfileLocalHelpTableTelLocal help telephone number. Only digit characters are allowed.
Note that sipCallSvcProfileLocalHelpTableName and sipCallSvcProfileLocalHelpTableTel
must be set sequentially.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.14.3.5.1.3 |
voipExtMaxNumOfVoipDialPlanThe maximum number of VoIP dial plan supported by the system.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.4 |
voipExtDialPlanTableConfigure dialing plan entry of specified index in specified payphone charging table. SEQUENCE OF VoipExtDialPlanEntry .1.3.6.1.4.1.890.1.5.13.5.16.14.5 |
voipExtDialPlanEntryAn entry of voipExtDialPlanTable. VoipExtDialPlanEntry .1.3.6.1.4.1.890.1.5.13.5.16.14.5.1 |
voipExtDialPlanNameDialing plan table name.ro DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.14.5.1.1 |
voipExtDialPlanIndexro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.5.1.2 |
voipExtDialPlanPatternup to 47 characters, allow digit, '*', and '#' characters and
meaning characters that include 'x', '.', '|' and range format
characters that include '~', ',' and parenthesis '(', ')'
and brackets '[', ']' and at most one parenthesis pair,
examples: '002(x.)', '0(x.)', and '(x.)'rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.14.5.1.3 |
voipExtDialPlanRuleAllowed characters are 0~9, and '\c' stand for country code,
'\d' stand for national destination code,
'\1' stand for matched string enclosed by the parenthesis pair,
and 'deny' stand for the pattern specified is not allowed.
Examples: '\1', '\c\1', and '\c\d\1'.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.14.5.1.4 |
voipExtDialPlanRowStatusThis object is used to create a new entry or delete an existing entry in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.14.5.1.5 |
voipExtSip OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.16.14.6 |
voipExtSipIp OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.16.14.6.1 |
voipExtSipSignalIpSignaling Iprw IpAddress .1.3.6.1.4.1.890.1.5.13.5.16.14.6.1.1 |
voipExtSipSignalMaskSignaling network mask, 0~32rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.6.1.2 |
voipExtSipSignalVid1~4094rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.16.14.6.1.3 |
voipExtSipMediaIpRTP IPrw IpAddress .1.3.6.1.4.1.890.1.5.13.5.16.14.6.1.4 |
voipExtSipMediaMaskRTP network mask, 0~32rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.6.1.5 |
voipExtSipMediaVid1~4094rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.16.14.6.1.6 |
voipExtSipDnsIpPrimary DNS IP. Set to '0.0.0.0' will clear both voipExtSipDnsIp and voipExtSipDnsIp2rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.16.14.6.1.7 |
voipExtSipDnsIp2Secondary DNS IP. could not be set when voipExtSipDnsIp is '0.0.0.0',
set voipExtSipDnsIp or voipExtSipDnsIp2 with '0.0.0.0' to clear.rw IpAddress .1.3.6.1.4.1.890.1.5.13.5.16.14.6.1.8 |
voipExtSipMaxNumOfVoipRoutero INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.6.2 |
voipExtSipRouteTable SEQUENCE OF VoipExtSipRouteEntry .1.3.6.1.4.1.890.1.5.13.5.16.14.6.3 |
voipExtSipRouteEntryAn entry of voipExtSipRouteTable. VoipExtSipRouteEntry .1.3.6.1.4.1.890.1.5.13.5.16.14.6.3.1 |
voipExtSipRouteIpIP address.ro IpAddress .1.3.6.1.4.1.890.1.5.13.5.16.14.6.3.1.1 |
voipExtSipRouteGatewayGateway IP.ro IpAddress .1.3.6.1.4.1.890.1.5.13.5.16.14.6.3.1.2 |
voipExtSipRouteMaskNetwork mask.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.6.3.1.3 |
voipExtSipRouteMetricMetric number of the route.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.6.3.1.4 |
voipExtSipRouteRowStatusThis object is used to create a new entry or delete an existing entry in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.16.14.6.3.1.5 |
voipExtSipRegcountregister times per second, 1~255. 0 means off.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.6.4 |
voipExtSipCptReorderTimeout of re-order tone, 5~300rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.6.5 |
voipExtSipCptHowlerTimeout of re-order tone, 5~300rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.6.6 |
voipExtSipCptAlertingTimeout of re-order tone, 60~1200rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.6.7 |
voipExtSipPktLogSIP packet log on/offrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.6.8 |
voipExtSipPktLogClearSet 1 to clear SIP packet logrw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.6.9 |
voipExtSipLineConfTableThis table includes common attributes describing the VoIP line. SEQUENCE OF VoipExtSipLineConfEntry .1.3.6.1.4.1.890.1.5.13.5.16.14.7 |
voipExtSipLineConfEntryAn entry in voipExtSipLineConfTable. VoipExtSipLineConfEntry .1.3.6.1.4.1.890.1.5.13.5.16.14.7.1 |
voipExtSipLineConfHotlineOnrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.7.1.1 |
voipExtSipLineConfHotlineNoonly alphanumeric characters and '+' are allowed,
or use two quotation marks () to clear the field.
Note: '+' only is allowed at the first characterrw DisplayString .1.3.6.1.4.1.890.1.5.13.5.16.14.7.1.2 |
voipExtSipLineConfHotlineTimeout0~255 seconds, 0 means dialling immediately.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.16.14.7.1.3 |
voipExtSipLineConfTaxmetering moderw Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.7.1.4 |
voipExtSipLineStatusTableThe table displays VoIP line status. This table is supported by R4.01 and later versions. SEQUENCE OF VoipExtSipLineStatusEntry .1.3.6.1.4.1.890.1.5.13.5.16.14.8 |
voipExtSipLineStatusEntryAn entry of voipExtSipLineStatTable. VoipExtSipLineStatusEntry .1.3.6.1.4.1.890.1.5.13.5.16.14.8.1 |
voipExtSipLineStatusFxsStatusFXS status of the line.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.8.1.1 |
voipExtSipLineStatusServiceStatusService status of the line.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.8.1.2 |
voipExtSipLineStatusLocalcallStatusLocalcall status of the line.ro Enumeration .1.3.6.1.4.1.890.1.5.13.5.16.14.8.1.3 |
ima OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.17 |
imaGroupTableThis table is supported by R5.03 and later versions. SEQUENCE OF ImaGroupEntry .1.3.6.1.4.1.890.1.5.13.5.17.1 |
imaGroupEntryAn entry of imaGroupTable. ImaGroupEntry .1.3.6.1.4.1.890.1.5.13.5.17.1.1 |
imaGroupIndexro INTEGER .1.3.6.1.4.1.890.1.5.13.5.17.1.1.1 |
imaGroupClkModerw Enumeration .1.3.6.1.4.1.890.1.5.13.5.17.1.1.2 |
imaGroupVersionrw Enumeration .1.3.6.1.4.1.890.1.5.13.5.17.1.1.3 |
imaGroupChan OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.5.17.2 |
imaGroupChanNumTableThis table is supported by R5.03 and later versions. SEQUENCE OF ImaGroupChanNumEntry .1.3.6.1.4.1.890.1.5.13.5.17.2.1 |
imaGroupChanNumEntryAn entry of ImaGroupChanNumTable. ImaGroupChanNumEntry .1.3.6.1.4.1.890.1.5.13.5.17.2.1.1 |
imaGroupChanNumSlotro INTEGER .1.3.6.1.4.1.890.1.5.13.5.17.2.1.1.1 |
imaGroupChanNumMaximumro INTEGER .1.3.6.1.4.1.890.1.5.13.5.17.2.1.1.2 |
imaGroupChanNumCurrentTotalro INTEGER .1.3.6.1.4.1.890.1.5.13.5.17.2.1.1.3 |
imaGroupChanNumCurrentPvcro INTEGER .1.3.6.1.4.1.890.1.5.13.5.17.2.1.1.4 |
imaGroupChanNumCurrentDtpvcro INTEGER .1.3.6.1.4.1.890.1.5.13.5.17.2.1.1.5 |
imaGroupPvcTableThis table includes IMA Group PVC configuration.
This table is supported by R5.03 and later versions. SEQUENCE OF ImaGroupPvcEntry .1.3.6.1.4.1.890.1.5.13.5.17.2.2 |
imaGroupPvcEntryAn entry of imaGroupPvcTable. ImaGroupPvcEntry .1.3.6.1.4.1.890.1.5.13.5.17.2.2.1 |
imaGroupPvcGroupIndexro INTEGER .1.3.6.1.4.1.890.1.5.13.5.17.2.2.1.1 |
imaGroupPvcVpiVPI of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.17.2.2.1.2 |
imaGroupPvcVciVCI of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.17.2.2.1.3 |
imaGroupPvcPvidPVID of the pvc.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.17.2.2.1.4 |
imaGroupPvcEncapEncapsulation of the pvc.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.17.2.2.1.5 |
imaGroupPvcPrioritypriority of the pvc.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.17.2.2.1.6 |
imaGruopPvcProfileThe value of this object identifies the row in the atmProfileTable, which applies for this pvc.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.17.2.2.1.7 |
imaGroupPvcRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.17.2.2.1.8 |
imaGroupPvcEgressTagEncapsulation of the pvc.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.17.2.2.1.9 |
imaGroupDtPvcTableThis table includes IMA Group Double Tagging PVC configuration.
This table is supported by R5.03 and later versions. SEQUENCE OF ImaGroupDtPvcEntry .1.3.6.1.4.1.890.1.5.13.5.17.2.3 |
imaGroupDtPvcEntryAn entry of imaGroupDtPvcTable. ImaGroupDtPvcEntry .1.3.6.1.4.1.890.1.5.13.5.17.2.3.1 |
imaGroupDTPvcGroupIndexro INTEGER .1.3.6.1.4.1.890.1.5.13.5.17.2.3.1.1 |
imaGroupDtPvcVpiVPI of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.17.2.3.1.2 |
imaGroupDtPvcVciVCI of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.17.2.3.1.3 |
imaGroupDtPvcSvids-tag of the pvc.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.17.2.3.1.4 |
imaGroupDtPvcCvidc-tag of the pvc.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.17.2.3.1.5 |
imaGroupDtPvcEncapEncapsulation of the pvc.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.17.2.3.1.6 |
imaGroupDtPvcSPrioritys-priority of the pvc.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.17.2.3.1.7 |
imaGroupDtPvcCPriorityc-priority of the pvc.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.17.2.3.1.8 |
imaGroupDtPvcProfileThe value of this object identifies the row in the atmProfileTable, which applies for this pvc.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.17.2.3.1.9 |
imaGroupDtPvcRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.17.2.3.1.10 |
imaMgmtPvcTableThis table includes IMA Management PVC configuration.
This table is supported by R5.03 and later versions. SEQUENCE OF ImaMgmtPvcEntry .1.3.6.1.4.1.890.1.5.13.5.17.3 |
imaMgmtPvcEntryAn entry of imaMgmtPvcTable. ImaMgmtPvcEntry .1.3.6.1.4.1.890.1.5.13.5.17.3.1 |
imaMgmtPvcGroupIndexro INTEGER .1.3.6.1.4.1.890.1.5.13.5.17.3.1.1 |
imaMgmtPvcVpiVPI of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.17.3.1.2 |
imaMgmtPvcVciVCI of the pvc.ro INTEGER .1.3.6.1.4.1.890.1.5.13.5.17.3.1.3 |
imaMgmtPvcPvidPVID of the pvc.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.13.5.17.3.1.4 |
imaMgmtPvcEncapEncapsulation of the pvc.rw Enumeration .1.3.6.1.4.1.890.1.5.13.5.17.3.1.5 |
imaMgmtPvcPrioritypriority of the pvc.rw INTEGER .1.3.6.1.4.1.890.1.5.13.5.17.3.1.6 |
imaMgmtPvcProfileThe value of this object identifies the row in the atmProfileTable, which applies for this pvc.rw DisplayString .1.3.6.1.4.1.890.1.5.13.5.17.3.1.7 |
imaMgmtPvcRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.13.5.17.3.1.8 |
imaMgmtPvcManagedIpro IpAddress .1.3.6.1.4.1.890.1.5.13.5.17.3.1.9 |
imaMgmtPvcGatewayIpro IpAddress .1.3.6.1.4.1.890.1.5.13.5.17.3.1.10 |
ies5005 OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.7 |
ies6000 OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.13.8 |