Home/Catalog/VDSL-LINE-MIB

VDSL-LINE-MIB

The MIB module defining objects for the management of a pair of VDSL transceivers at each end of the VDSL line. Each such line has an entry in an ifTable which may include multiple transceiver lines. An agent may reside at either end of the VDSL line. However, the MIB is designed to require no management communication between them beyond that inherent in the low-level VDSL line protocol. The agent may monitor and control this protocol for its needs. VDSL lines may support optional Fast or Interleaved channels. If these are supported, additional entries corresponding to the supported channels must be created in the ifTable. Thus a VDSL line that supports both channels will have three entries in the ifTable, one for each physical, fast, and interleaved, whose ifType values are equal to vdsl(97), fast(125), and interleaved(124), respectively. The ifStackTable is used to represent the relationship between the entries. Naming Conventions: Vtuc -- (VTUC) transceiver at near (Central) end of line Vtur -- (VTUR) transceiver at Remote end of line Vtu -- One of either Vtuc or Vtur Curr -- Current Prev -- Previous Atn -- Attenuation ES -- Errored Second. SES -- Severely Errored Second UAS -- Unavailable Second LCS -- Line Code Specific Lof -- Loss of Frame Lol -- Loss of Link Los -- Loss of Signal Lpr -- Loss of Power xxxs -- Sum of Seconds in which xxx has occured (e.g., xxx = Lof, Los, Lpr, Lol) Max -- Maximum Mgn -- Margin Min -- Minimum Psd -- Power Spectral Density Snr -- Signal to Noise Ratio Tx -- Transmit Blks -- Blocks Copyright (C) The Internet Society (2004). This version of this MIB module is part of RFC 3728: see the RFC itself for full legal notices.
Main OID:
vdslMIB.1.3.6.1.2.1.10.97
187
Objects
Active
Status
7
Dependencies

Imported Objects

SNMPv2-SMI
HCNUM-TC
SNMPv2-TC
HC-PerfHist-TC-MIB
SNMPv2-CONF
IF-MIB
SNMP-FRAMEWORK-MIB

Objects

187 total
Object Name
vdslMIBThe MIB module defining objects for the management of a pair of VDSL transceivers at each end of the VDSL line. Each such line has an entry in an ifTable which may include multiple transceiver lines. An agent may reside at either end of the VDSL line. However, the MIB is designed to require no management communication between them beyond that inherent in the low-level VDSL line protocol. The agent may monitor and control this protocol for its needs. VDSL lines may support optional Fast or Interleaved channels. If these are supported, additional entries corresponding to the supported channels must be created in the ifTable. Thus a VDSL line that supports both channels will have three entries in the ifTable, one for each physical, fast, and interleaved, whose ifType values are equal to vdsl(97), fast(125), and interleaved(124), respectively. The ifStackTable is used to represent the relationship between the entries. Naming Conventions: Vtuc -- (VTUC) transceiver at near (Central) end of line Vtur -- (VTUR) transceiver at Remote end of line Vtu -- One of either Vtuc or Vtur Curr -- Current Prev -- Previous Atn -- Attenuation ES -- Errored Second. SES -- Severely Errored Second UAS -- Unavailable Second LCS -- Line Code Specific Lof -- Loss of Frame Lol -- Loss of Link Los -- Loss of Signal Lpr -- Loss of Power xxxs -- Sum of Seconds in which xxx has occured (e.g., xxx = Lof, Los, Lpr, Lol) Max -- Maximum Mgn -- Margin Min -- Minimum Psd -- Power Spectral Density Snr -- Signal to Noise Ratio Tx -- Transmit Blks -- Blocks Copyright (C) The Internet Society (2004). This version of this MIB module is part of RFC 3728: see the RFC itself for full legal notices.
MODULE-IDENTITY
.1.3.6.1.2.1.10.97
vdslLineMib
OBJECT IDENTIFIER
.1.3.6.1.2.1.10.97.1
vdslNotifications
OBJECT IDENTIFIER
.1.3.6.1.2.1.10.97.1.0
vdslPerfLofsThreshNotificationLoss of Framing 15-minute interval threshold (vdslLineAlarmConfThresh15MinLofs) reached.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.97.1.0.1
vdslPerfLossThreshNotificationLoss of Signal 15-minute interval threshold (vdslLineAlarmConfThresh15MinLoss) reached.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.97.1.0.2
vdslPerfLprsThreshNotificationLoss of Power 15-minute interval threshold (vdslLineAlarmConfThresh15MinLprs) reached.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.97.1.0.3
vdslPerfLolsThreshNotificationLoss of Link 15-minute interval threshold (vdslLineAlarmConfThresh15MinLols) reached.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.97.1.0.4
vdslPerfESsThreshNotificationErrored Seconds 15-minute interval threshold (vdslLineAlarmConfThresh15MinESs) reached.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.97.1.0.5
vdslPerfSESsThreshNotificationSeverely Errored Seconds 15-minute interval threshold (vdslLineAlarmConfThresh15MinSESs) reached.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.97.1.0.6
vdslPerfUASsThreshNotificationUnavailable Seconds 15-minute interval threshold (vdslLineAlarmConfThresh15MinUASs) reached.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.97.1.0.7
vdslDownMaxSnrMgnNotificationThe downstream Signal to Noise Margin exceeded vdslLineConfDownMaxSnrMgn. The object vdslPhysCurrSnrMgn will contain the Signal to Noise margin as measured by the VTU-R.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.97.1.0.8
vdslDownMinSnrMgnNotificationThe downstream Signal to Noise Margin fell below vdslLineConfDownMinSnrMgn. The object vdslPhysCurrSnrMgn will contain the Signal to Noise margin as measured by the VTU-R.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.97.1.0.9
vdslUpMaxSnrMgnNotificationThe upstream Signal to Noise Margin exceeded vdslLineConfUpMaxSnrMgn. The object vdslPhysCurrSnrMgn will contain the Signal to Noise margin as measured by the VTU-C.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.97.1.0.10
vdslUpMinSnrMgnNotificationThe upstream Signal to Noise Margin fell below vdslLineConfUpMinSnrMgn. The object vdslPhysCurrSnrMgn will contain the Signal to Noise margin as measured by the VTU-C.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.97.1.0.11
vdslInitFailureNotificationVtu initialization failed. See vdslPhysCurrStatus for potential reasons.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.97.1.0.12
vdslMibObjects
OBJECT IDENTIFIER
.1.3.6.1.2.1.10.97.1.1
vdslLineTableThis table includes common attributes describing both ends of the line. It is required for all VDSL physical interfaces. VDSL physical interfaces are those ifEntries where ifType is equal to vdsl(97).
SEQUENCE OF VdslLineEntry
.1.3.6.1.2.1.10.97.1.1.1
vdslLineEntryAn entry in the vdslLineTable.
VdslLineEntry
.1.3.6.1.2.1.10.97.1.1.1.1
vdslLineCodingSpecifies the VDSL coding type used on this line.ro
VdslLineCodingType
.1.3.6.1.2.1.10.97.1.1.1.1.1
vdslLineTypeDefines the type of VDSL physical line entity that exists, by defining whether and how the line is channelized. If the line is channelized, the value will be other than noChannel(1). This object defines which channel type(s) are supported. Defined values are: noChannel(1) -- no channels exist fastOnly(2) -- only fast channel exists interleavedOnly(3) -- only interleaved channel exists fastOrInterleaved(4) -- either fast or interleaved channel -- exist, but only one at a time fastAndInterleaved(5) -- both fast and interleaved channels -- exist Note that 'slow' and 'interleaved' refer to the same channel. In the case that the line is channelized, the manager can use the ifStackTable to determine the ifIndex for the associated channel(s).ro
Enumeration
.1.3.6.1.2.1.10.97.1.1.1.1.2
vdslLineConfProfileThe value of this object identifies the row in the VDSL Line Configuration Profile Table, vdslLineConfProfileTable, which applies for this VDSL line, and channels if applicable. This object MUST be maintained in a persistent manner.rw
SnmpAdminString
.1.3.6.1.2.1.10.97.1.1.1.1.3
vdslLineAlarmConfProfileThe value of this object identifies the row in the VDSL Line Alarm Configuration Profile Table, vdslLineAlarmConfProfileTable, which applies to this VDSL line, and channels if applicable. This object MUST be maintained in a persistent manner.rw
SnmpAdminString
.1.3.6.1.2.1.10.97.1.1.1.1.4
vdslPhysTableThis table provides one row for each Vtu. Each row contains the Physical Layer Parameters table for that Vtu. VDSL physical interfaces are those ifEntries where ifType is equal to vdsl(97).
SEQUENCE OF VdslPhysEntry
.1.3.6.1.2.1.10.97.1.1.2
vdslPhysEntryAn entry in the vdslPhysTable.
VdslPhysEntry
.1.3.6.1.2.1.10.97.1.1.2.1
vdslPhysSideIdentifies whether the transceiver is the Vtuc or Vtur.
VdslLineEntity
.1.3.6.1.2.1.10.97.1.1.2.1.1
vdslPhysInvSerialNumberThe vendor specific string that identifies the vendor equipment.ro
SnmpAdminString
.1.3.6.1.2.1.10.97.1.1.2.1.2
vdslPhysInvVendorIDThe vendor ID code is a copy of the binary vendor identification field expressed as readable characters in hexadecimal notation.ro
SnmpAdminString
.1.3.6.1.2.1.10.97.1.1.2.1.3
vdslPhysInvVersionNumberThe vendor specific version number sent by this Vtu as part of the initialization messages. It is a copy of the binary version number field expressed as readable characters in hexadecimal notation.ro
SnmpAdminString
.1.3.6.1.2.1.10.97.1.1.2.1.4
vdslPhysCurrSnrMgnNoise Margin as seen by this Vtu with respect to its received signal in 0.25dB. The effective range is -31.75 to +31.75 dB.ro
Integer32 (-127..127) UNITS "0.25dBm"
.1.3.6.1.2.1.10.97.1.1.2.1.5
vdslPhysCurrAtnMeasured difference in the total power transmitted by the peer Vtu and the total power received by this Vtu. The effective range is 0 to +63.75 dB.ro
Gauge32
.1.3.6.1.2.1.10.97.1.1.2.1.6
vdslPhysCurrStatusIndicates current state of the Vtu line. This is a bit-map of possible conditions. The various bit positions are: 0 noDefect There are no defects on the line. 1 lossOfFraming Vtu failure due to not receiving a valid frame. 2 lossOfSignal Vtu failure due to not receiving signal. 3 lossOfPower Vtu failure due to loss of power. 4 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. 5 lossOfLink Vtu failure due to inability to link with peer Vtu. Set whenever the transceiver is in the 'Warm Start' state. 6 dataInitFailure Vtu failure during initialization due to bit errors corrupting startup exchange data. 7 configInitFailure Vtu failure during initialization due to peer Vtu not able to support requested configuration. 8 protocolInitFailure Vtu failure during initialization due to incompatible protocol used by the peer Vtu. 9 noPeerVtuPresent Vtu failure during initialization due to no activation sequence detected from peer Vtu. This is intended to supplement ifOperStatus.ro
Bits
.1.3.6.1.2.1.10.97.1.1.2.1.7
vdslPhysCurrOutputPwrMeasured total output power transmitted by this VTU. This is the measurement that was reported during the last activation sequence.ro
Integer32
.1.3.6.1.2.1.10.97.1.1.2.1.8
vdslPhysCurrAttainableRateIndicates the maximum currently attainable data rate in steps of 1000 bits/second by the Vtu. This value will be equal to or greater than vdslPhysCurrLineRate. Note that for SCM, the minimum and maximum data rates are equal. Note: 1 kbps = 1000 bps.ro
Gauge32 UNITS "kbps"
.1.3.6.1.2.1.10.97.1.1.2.1.9
vdslPhysCurrLineRateIndicates the current data rate in steps of 1000 bits/second by the Vtu. This value will be less than or equal to vdslPhysCurrAttainableRate. Note: 1 kbps = 1000 bps.ro
Gauge32 UNITS "kbps"
.1.3.6.1.2.1.10.97.1.1.2.1.10
vdslChanTableThis table provides one row for each Vtu channel. VDSL channel interfaces are those ifEntries where ifType is equal to interleave(124) or fast(125).
SEQUENCE OF VdslChanEntry
.1.3.6.1.2.1.10.97.1.1.3
vdslChanEntryAn entry in the vdslChanTable.
VdslChanEntry
.1.3.6.1.2.1.10.97.1.1.3.1
vdslChanInterleaveDelayInterleave Delay for this channel. Interleave delay applies only to the interleave (slow) channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency. In the case where the ifType is fast(125), return a value of zero.ro
Gauge32 UNITS "milliseconds"
.1.3.6.1.2.1.10.97.1.1.3.1.1
vdslChanCrcBlockLengthIndicates the length of the channel data-block on which the CRC operates.ro
Gauge32 UNITS "bytes"
.1.3.6.1.2.1.10.97.1.1.3.1.2
vdslChanCurrTxRateActual transmit data rate on this channel. Note: 1 kbps = 1000 bps.ro
Gauge32 UNITS "kbps"
.1.3.6.1.2.1.10.97.1.1.3.1.3
vdslChanCurrTxSlowBurstProtectActual level of impulse noise (burst) protection for an interleaved (slow) channel. This parameter is not applicable to fast channels. For fast channels, a value of zero shall be returned.ro
Gauge32
.1.3.6.1.2.1.10.97.1.1.3.1.4
vdslChanCurrTxFastFecActual Forward Error Correction (FEC) redundancy related overhead for a fast channel. This parameter is not applicable to an interleaved (slow) channel. For interleaved channels, a value of zero shall be returned.ro
Gauge32
.1.3.6.1.2.1.10.97.1.1.3.1.5
vdslPerfDataTableThis table provides one row for each VDSL physical interface. VDSL physical interfaces are those ifEntries where ifType is equal to vdsl(97).
SEQUENCE OF VdslPerfDataEntry
.1.3.6.1.2.1.10.97.1.1.4
vdslPerfDataEntryAn entry in the vdslPerfDataTable.
VdslPerfDataEntry
.1.3.6.1.2.1.10.97.1.1.4.1
vdslPerfDataValidIntervalsValid Intervals per definition found in HC-PerfHist-TC-MIB.ro
HCPerfValidIntervals UNITS "intervals"
.1.3.6.1.2.1.10.97.1.1.4.1.1
vdslPerfDataInvalidIntervalsInvalid Intervals per definition found in HC-PerfHist-TC-MIB.ro
HCPerfInvalidIntervals UNITS "intervals"
.1.3.6.1.2.1.10.97.1.1.4.1.2
vdslPerfDataLofsCount of seconds since the unit was last reset that there was Loss of Framing.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.4.1.3
vdslPerfDataLossCount of seconds since the unit was last reset that there was Loss of Signal.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.4.1.4
vdslPerfDataLprsCount of seconds since the unit was last reset that there was Loss of Power.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.4.1.5
vdslPerfDataLolsCount of seconds since the unit was last reset that there was Loss of Link.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.4.1.6
vdslPerfDataESsCount of Errored Seconds since the unit was last reset. An Errored Second is a one-second interval containing one or more CRC anomalies, or one or more LOS or LOF defects.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.4.1.7
vdslPerfDataSESsCount of Severely Errored Seconds since the unit was last reset.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.4.1.8
vdslPerfDataUASsCount of Unavailable Seconds since the unit was last reset.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.4.1.9
vdslPerfDataInitsCount of the line initialization attempts since the unit was last reset. This count includes both successful and failed attempts.ro
Unsigned32 UNITS "occurrences"
.1.3.6.1.2.1.10.97.1.1.4.1.10
vdslPerfDataCurr15MinTimeElapsedTotal elapsed seconds in this interval.ro
HCPerfTimeElapsed UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.4.1.11
vdslPerfDataCurr15MinLofsCount of seconds during this interval that there was Loss of Framing.ro
HCPerfCurrentCount UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.4.1.12
vdslPerfDataCurr15MinLossCount of seconds during this interval that there was Loss of Signal.ro
HCPerfCurrentCount UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.4.1.13
vdslPerfDataCurr15MinLprsCount of seconds during this interval that there was Loss of Power.ro
HCPerfCurrentCount UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.4.1.14
vdslPerfDataCurr15MinLolsCount of seconds during this interval that there was Loss of Link.ro
HCPerfCurrentCount UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.4.1.15
vdslPerfDataCurr15MinESsCount of Errored Seconds during this interval. An Errored Second is a one-second interval containing one or more CRC anomalies, or one or more LOS or LOF defects.ro
HCPerfCurrentCount UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.4.1.16
vdslPerfDataCurr15MinSESsCount of Severely Errored Seconds during this interval.ro
HCPerfCurrentCount UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.4.1.17
vdslPerfDataCurr15MinUASsCount of Unavailable Seconds during this interval.ro
HCPerfCurrentCount UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.4.1.18
vdslPerfDataCurr15MinInitsCount of the line initialization attempts during this interval. This count includes both successful and failed attempts.ro
HCPerfCurrentCount UNITS "occurrences"
.1.3.6.1.2.1.10.97.1.1.4.1.19
vdslPerfData1DayValidIntervalsValid Intervals per definition found in HC-PerfHist-TC-MIB.ro
HCPerfValidIntervals UNITS "intervals"
.1.3.6.1.2.1.10.97.1.1.4.1.20
vdslPerfData1DayInvalidIntervalsInvalid Intervals per definition found in HC-PerfHist-TC-MIB.ro
HCPerfInvalidIntervals UNITS "intervals"
.1.3.6.1.2.1.10.97.1.1.4.1.21
vdslPerfDataCurr1DayTimeElapsedNumber of seconds that have elapsed since the beginning of the current 1-day interval.ro
HCPerfTimeElapsed UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.4.1.22
vdslPerfDataCurr1DayLofsCount of Loss of Framing (LOF) Seconds since the beginning of the current 1-day interval.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.4.1.23
vdslPerfDataCurr1DayLossCount of Loss of Signal (LOS) Seconds since the beginning of the current 1-day interval.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.4.1.24
vdslPerfDataCurr1DayLprsCount of Loss of Power (LPR) Seconds since the beginning of the current 1-day interval.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.4.1.25
vdslPerfDataCurr1DayLolsCount of Loss of Link (LOL) Seconds since the beginning of the current 1-day interval.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.4.1.26
vdslPerfDataCurr1DayESsCount of Errored Seconds (ES) since the beginning of the current 1-day interval.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.4.1.27
vdslPerfDataCurr1DaySESsCount of Severely Errored Seconds (SES) since the beginning of the current 1-day interval.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.4.1.28
vdslPerfDataCurr1DayUASsCount of Unavailable Seconds (UAS) since the beginning of the current 1-day interval.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.4.1.29
vdslPerfDataCurr1DayInitsCount of the line initialization attempts since the beginning of the current 1-day interval. This count includes both successful and failed attempts.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.4.1.30
vdslPerfIntervalTableThis table provides one row for each Vtu performance data collection interval. VDSL physical interfaces are those ifEntries where ifType is equal to vdsl(97).
SEQUENCE OF VdslPerfIntervalEntry
.1.3.6.1.2.1.10.97.1.1.5
vdslPerfIntervalEntryAn entry in the vdslPerfIntervalTable.
VdslPerfIntervalEntry
.1.3.6.1.2.1.10.97.1.1.5.1
vdslPerfIntervalNumberPerformance Data Interval number 1 is the most recent previous interval; interval 96 is 24 hours ago. Intervals 2 to 96 are optional.
Unsigned32
.1.3.6.1.2.1.10.97.1.1.5.1.1
vdslPerfIntervalLofsCount of seconds in the interval when there was Loss of Framing.ro
HCPerfIntervalCount UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.5.1.2
vdslPerfIntervalLossCount of seconds in the interval when there was Loss of Signal.ro
HCPerfIntervalCount UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.5.1.3
vdslPerfIntervalLprsCount of seconds in the interval when there was Loss of Power.ro
HCPerfIntervalCount UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.5.1.4
vdslPerfIntervalLolsCount of seconds in the interval when there was Loss of Link.ro
HCPerfIntervalCount UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.5.1.5
vdslPerfIntervalESsCount of Errored Seconds (ES) in the interval. An Errored Second is a one-second interval containing one or more CRC anomalies, one or more LOS or LOF defects.ro
HCPerfIntervalCount UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.5.1.6
vdslPerfIntervalSESsCount of Severely Errored Seconds in the interval.ro
HCPerfIntervalCount UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.5.1.7
vdslPerfIntervalUASsCount of Unavailable Seconds in the interval.ro
HCPerfIntervalCount UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.5.1.8
vdslPerfIntervalInitsCount of the line initialization attempts during this interval. This count includes both successful and failed attempts.ro
HCPerfIntervalCount (HC-PerfHist-TC-MIB)
.1.3.6.1.2.1.10.97.1.1.5.1.9
vdslPerf1DayIntervalTableThis table provides one row for each VDSL performance data collection interval. This table contains live data from equipment. As such, it is NOT persistent.
SEQUENCE OF VdslPerf1DayIntervalEntry
.1.3.6.1.2.1.10.97.1.1.6
vdslPerf1DayIntervalEntryAn entry in the vdslPerf1DayIntervalTable.
VdslPerf1DayIntervalEntry
.1.3.6.1.2.1.10.97.1.1.6.1
vdslPerf1DayIntervalNumberHistory Data Interval number. Interval 1 is the most recent previous day; interval 30 is 30 days ago. Intervals 2 to 30 are optional.
Unsigned32
.1.3.6.1.2.1.10.97.1.1.6.1.1
vdslPerf1DayIntervalMoniSecsThe amount of time in the 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason.ro
HCPerfTimeElapsed UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.6.1.2
vdslPerf1DayIntervalLofsCount of Loss of Frame (LOF) Seconds during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.6.1.3
vdslPerf1DayIntervalLossCount of Loss of Signal (LOS) Seconds during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.6.1.4
vdslPerf1DayIntervalLprsCount of Loss of Power (LPR) Seconds during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.6.1.5
vdslPerf1DayIntervalLolsCount of Loss of Link (LOL) Seconds during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.6.1.6
vdslPerf1DayIntervalESsCount of Errored Seconds (ES) during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.6.1.7
vdslPerf1DayIntervalSESsCount of Severely Errored Seconds (SES) during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.6.1.8
vdslPerf1DayIntervalUASsCount of Unavailable Seconds (UAS) during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.6.1.9
vdslPerf1DayIntervalInitsCount of the line initialization attempts during the 1-day interval as measured by vdslPerf1DayIntervalMoniSecs. This count includes both successful and failed attempts.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.6.1.10
vdslChanPerfDataTableThis table provides one row for each Vtu channel. VDSL channel interfaces are those ifEntries where ifType is equal to interleave(124) or fast(125).
SEQUENCE OF VdslChanPerfDataEntry
.1.3.6.1.2.1.10.97.1.1.7
vdslChanPerfDataEntryAn entry in the vdslChanPerfDataTable.
VdslChanPerfDataEntry
.1.3.6.1.2.1.10.97.1.1.7.1
vdslChanValidIntervalsValid Intervals per definition found in HC-PerfHist-TC-MIB.ro
HCPerfValidIntervals UNITS "intervals"
.1.3.6.1.2.1.10.97.1.1.7.1.1
vdslChanInvalidIntervalsInvalid Intervals per definition found in HC-PerfHist-TC-MIB.ro
HCPerfInvalidIntervals UNITS "intervals"
.1.3.6.1.2.1.10.97.1.1.7.1.2
vdslChanFixedOctetsCount of corrected octets since the unit was last reset.ro
ZeroBasedCounter64 UNITS "octets"
.1.3.6.1.2.1.10.97.1.1.7.1.3
vdslChanBadBlksCount of uncorrectable blocks since the unit was last reset.ro
ZeroBasedCounter64 UNITS "blocks"
.1.3.6.1.2.1.10.97.1.1.7.1.4
vdslChanCurr15MinTimeElapsedTotal elapsed seconds in this interval.ro
HCPerfTimeElapsed UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.7.1.5
vdslChanCurr15MinFixedOctetsCount of corrected octets in this interval.ro
HCPerfCurrentCount UNITS "octets"
.1.3.6.1.2.1.10.97.1.1.7.1.6
vdslChanCurr15MinBadBlksCount of uncorrectable blocks in this interval.ro
HCPerfCurrentCount UNITS "blocks"
.1.3.6.1.2.1.10.97.1.1.7.1.7
vdslChan1DayValidIntervalsValid Intervals per definition found in HC-PerfHist-TC-MIB.ro
HCPerfValidIntervals (HC-PerfHist-TC-MIB)
.1.3.6.1.2.1.10.97.1.1.7.1.8
vdslChan1DayInvalidIntervalsInvalid Intervals per definition found in HC-PerfHist-TC-MIB.ro
HCPerfInvalidIntervals (HC-PerfHist-TC-MIB)
.1.3.6.1.2.1.10.97.1.1.7.1.9
vdslChanCurr1DayTimeElapsedNumber of seconds that have elapsed since the beginning of the current 1-day interval.ro
HCPerfTimeElapsed UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.7.1.10
vdslChanCurr1DayFixedOctetsCount of corrected octets since the beginning of the current 1-day interval.ro
HCPerfCurrentCount UNITS "octets"
.1.3.6.1.2.1.10.97.1.1.7.1.11
vdslChanCurr1DayBadBlksCount of uncorrectable blocks since the beginning of the current 1-day interval.ro
HCPerfCurrentCount UNITS "blocks"
.1.3.6.1.2.1.10.97.1.1.7.1.12
vdslChanIntervalTableThis table provides one row for each Vtu channel data collection interval. VDSL channel interfaces are those ifEntries where ifType is equal to interleave(124) or fast(125).
SEQUENCE OF VdslChanIntervalEntry
.1.3.6.1.2.1.10.97.1.1.8
vdslChanIntervalEntryAn entry in the vdslChanIntervalTable.
VdslChanIntervalEntry
.1.3.6.1.2.1.10.97.1.1.8.1
vdslChanIntervalNumberPerformance Data Interval number 1 is the most recent previous interval; interval 96 is 24 hours ago. Intervals 2 to 96 are optional.
Unsigned32
.1.3.6.1.2.1.10.97.1.1.8.1.1
vdslChanIntervalFixedOctetsCount of corrected octets in this interval.ro
HCPerfIntervalCount UNITS "octets"
.1.3.6.1.2.1.10.97.1.1.8.1.2
vdslChanIntervalBadBlksCount of uncorrectable blocks in this interval.ro
HCPerfIntervalCount UNITS "blocks"
.1.3.6.1.2.1.10.97.1.1.8.1.3
vdslChan1DayIntervalTableThis table provides one row for each VDSL performance data collection interval. This table contains live data from equipment. As such, it is NOT persistent.
SEQUENCE OF VdslChan1DayIntervalEntry
.1.3.6.1.2.1.10.97.1.1.9
vdslChan1DayIntervalEntryAn entry in the vdslChan1DayIntervalTable.
VdslChan1DayIntervalEntry
.1.3.6.1.2.1.10.97.1.1.9.1
vdslChan1DayIntervalNumberHistory Data Interval number. Interval 1 is the most recent previous day; interval 30 is 30 days ago. Intervals 2 to 30 are optional.
Unsigned32
.1.3.6.1.2.1.10.97.1.1.9.1.1
vdslChan1DayIntervalMoniSecsThe amount of time in the 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason.ro
HCPerfTimeElapsed UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.9.1.2
vdslChan1DayIntervalFixedOctetsCount of corrected octets in this interval.ro
HCPerfCurrentCount UNITS "octets"
.1.3.6.1.2.1.10.97.1.1.9.1.3
vdslChan1DayIntervalBadBlksCount of uncorrectable blocks in this interval.ro
HCPerfCurrentCount UNITS "blocks"
.1.3.6.1.2.1.10.97.1.1.9.1.4
vdslLineConfProfileTableThis table contains information on the VDSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the VDSL line. Entries in this table MUST be maintained in a persistent manner.
SEQUENCE OF VdslLineConfProfileEntry
.1.3.6.1.2.1.10.97.1.1.11
vdslLineConfProfileEntryEach entry consists of a list of parameters that represents the configuration of a VDSL line. A default profile with an index of 'DEFVAL', will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document.
VdslLineConfProfileEntry
.1.3.6.1.2.1.10.97.1.1.11.1
vdslLineConfProfileNameThis object identifies a row in this table. A default profile with an index of 'DEFVAL', will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document.
SnmpAdminString
.1.3.6.1.2.1.10.97.1.1.11.1.1
vdslLineConfDownRateModeSpecifies the rate selection behavior for the line in the downstream direction. manual(1) forces the rate to the configured rate adaptAtInit(2) adapts the line based upon line quality.rw
Enumeration
.1.3.6.1.2.1.10.97.1.1.11.1.2
vdslLineConfUpRateModeSpecifies the rate selection behavior for the line in the upstream direction. manual(1) forces the rate to the configured rate adaptAtInit(2) adapts the line based upon line quality.rw
Enumeration
.1.3.6.1.2.1.10.97.1.1.11.1.3
vdslLineConfDownMaxPwrSpecifies the maximum aggregate downstream power level in the range 0 to 14.5 dBm.rw
Unsigned32
.1.3.6.1.2.1.10.97.1.1.11.1.4
vdslLineConfUpMaxPwrSpecifies the maximum aggregate upstream power level in the range 0 to 14.5 dBm.rw
Unsigned32
.1.3.6.1.2.1.10.97.1.1.11.1.5
vdslLineConfDownMaxSnrMgnSpecifies the maximum downstream Signal/Noise Margin in units of 0.25 dB, for a range of 0 to 31.75 dB.rw
Unsigned32
.1.3.6.1.2.1.10.97.1.1.11.1.6
vdslLineConfDownMinSnrMgnSpecifies the minimum downstream Signal/Noise Margin in units of 0.25 dB, for a range of 0 to 31.75 dB.rw
Unsigned32
.1.3.6.1.2.1.10.97.1.1.11.1.7
vdslLineConfDownTargetSnrMgnSpecifies the target downstream Signal/Noise Margin in units of 0.25 dB, for a range of 0 to 31.75 dB. This is the Noise Margin the transceivers must achieve with a BER of 10^-7 or better to successfully complete initialization.rw
Unsigned32
.1.3.6.1.2.1.10.97.1.1.11.1.8
vdslLineConfUpMaxSnrMgnSpecifies the maximum upstream Signal/Noise Margin in units of 0.25 dB, for a range of 0 to 31.75 dB.rw
Unsigned32
.1.3.6.1.2.1.10.97.1.1.11.1.9
vdslLineConfUpMinSnrMgnSpecifies the minimum upstream Signal/Noise Margin in units of 0.25 dB, for a range of 0 to 31.75 dB.rw
Unsigned32
.1.3.6.1.2.1.10.97.1.1.11.1.10
vdslLineConfUpTargetSnrMgnSpecifies the target upstream Signal/Noise Margin in units of 0.25 dB, for a range of 0 to 31.75 dB. This is the Noise Margin the transceivers must achieve with a BER of 10^-7 or better to successfully complete initialization.rw
Unsigned32
.1.3.6.1.2.1.10.97.1.1.11.1.11
vdslLineConfDownFastMaxDataRateSpecifies the maximum downstream fast channel data rate in steps of 1000 bits/second.rw
Unsigned32 UNITS "kbps"
.1.3.6.1.2.1.10.97.1.1.11.1.12
vdslLineConfDownFastMinDataRateSpecifies the minimum downstream fast channel data rate in steps of 1000 bits/second.rw
Unsigned32 UNITS "kbps"
.1.3.6.1.2.1.10.97.1.1.11.1.13
vdslLineConfDownSlowMaxDataRateSpecifies the maximum downstream slow channel data rate in steps of 1000 bits/second. The maximum aggregate downstream transmit speed of the line can be derived from the sum of maximum downstream fast and slow channel data rates.rw
Unsigned32 UNITS "kbps"
.1.3.6.1.2.1.10.97.1.1.11.1.14
vdslLineConfDownSlowMinDataRateSpecifies the minimum downstream slow channel data rate in steps of 1000 bits/second. The minimum aggregate downstream transmit speed of the line can be derived from the sum of minimum downstream fast and slow channel data rates.rw
Unsigned32 UNITS "kbps"
.1.3.6.1.2.1.10.97.1.1.11.1.15
vdslLineConfUpFastMaxDataRateSpecifies the maximum upstream fast channel data rate in steps of 1000 bits/second. The maximum aggregate upstream transmit speed of the line can be derived from the sum of maximum upstream fast and slow channel data rates.rw
Unsigned32 UNITS "kbps"
.1.3.6.1.2.1.10.97.1.1.11.1.16
vdslLineConfUpFastMinDataRateSpecifies the minimum upstream fast channel data rate in steps of 1000 bits/second. The minimum aggregate upstream transmit speed of the line can be derived from the sum of minimum upstream fast and slow channel data rates.rw
Unsigned32 UNITS "kbps"
.1.3.6.1.2.1.10.97.1.1.11.1.17
vdslLineConfUpSlowMaxDataRateSpecifies the maximum upstream slow channel data rate in steps of 1000 bits/second.rw
Unsigned32 UNITS "kbps"
.1.3.6.1.2.1.10.97.1.1.11.1.18
vdslLineConfUpSlowMinDataRateSpecifies the minimum upstream slow channel data rate in steps of 1000 bits/second.rw
Unsigned32 UNITS "kbps"
.1.3.6.1.2.1.10.97.1.1.11.1.19
vdslLineConfDownRateRatioFor dynamic rate adaptation at startup, the allocation of data rate in excess of the minimum data rate for each channel is controlled by the object. This object specifies the ratio of the allocation of the excess data rate between the fast and the slow channels. This allocation represents downstream Fast Channel Allocation / Slow Channel Allocation.rw
Unsigned32
.1.3.6.1.2.1.10.97.1.1.11.1.20
vdslLineConfUpRateRatioFor dynamic rate adaptation at startup, the allocation of data rate in excess of the minimum data rate for each channel is controlled by the object. This object specifies the ratio of the allocation of the excess data rate between the fast and the slow channels. This allocation represents upstream Fast Channel Allocation/Slow Channel Allocation.rw
Unsigned32
.1.3.6.1.2.1.10.97.1.1.11.1.21
vdslLineConfDownMaxInterDelaySpecifies the maximum interleave delay for the downstream slow channel.rw
Unsigned32
.1.3.6.1.2.1.10.97.1.1.11.1.22
vdslLineConfUpMaxInterDelaySpecifies the maximum interleave delay for the upstream slow channel.rw
Unsigned32
.1.3.6.1.2.1.10.97.1.1.11.1.23
vdslLineConfDownPboControlDownstream power backoff (PBO) control for this line. For transceivers which do not support downstream PBO control, this object MUST be fixed at disabled(1). If auto(2) is selected, the transceiver will automatically adjust the power backoff. If manual(3) is selected, then the transceiver will use the value from vdslLineConfDownPboLevel.rw
Enumeration
.1.3.6.1.2.1.10.97.1.1.11.1.24
vdslLineConfUpPboControlUpstream power backoff (PBO) control for this line. For transceivers which do not support upstream PBO control, this object MUST be fixed at disabled(1). If auto(2) is selected, the transceiver will automatically adjust the power backoff. If manual(3) is selected, then the transceiver will use the value from vdslLineConfUpPboLevel.rw
Enumeration
.1.3.6.1.2.1.10.97.1.1.11.1.25
vdslLineConfDownPboLevelSpecifies the downstream backoff level to be used when vdslLineConfDownPboControl = manual(3).rw
Unsigned32
.1.3.6.1.2.1.10.97.1.1.11.1.26
vdslLineConfUpPboLevelSpecifies the upstream backoff level to be used when vdslLineConfUpPboControl = manual(3).rw
Unsigned32
.1.3.6.1.2.1.10.97.1.1.11.1.27
vdslLineConfDeploymentScenarioThe VDSL line deployment scenario. When using fttCab(1), the VTU-C is located in a street cabinet. When using fttEx(2), the VTU-C is located at the central office. Changes to this value will have no effect on the transceiver.rw
Enumeration
.1.3.6.1.2.1.10.97.1.1.11.1.28
vdslLineConfAdslPresenceIndicates presence of ADSL service in the associated cable bundle/binder. none(1) indicates no ADSL service in the bundle adslOverPots(2) indicates ADSL service over POTS is present in the bundle adslOverISDN(3) indicates ADSL service over ISDN is present in the bundlerw
Enumeration
.1.3.6.1.2.1.10.97.1.1.11.1.29
vdslLineConfApplicableStandardThe VDSL standard to be used for the line. ansi(1) indicates ANSI standard etsi(2) indicates ETSI standard itu(3) indicates ITU standard other(4) indicates a standard other than the above.rw
Enumeration
.1.3.6.1.2.1.10.97.1.1.11.1.30
vdslLineConfBandPlanThe VDSL band plan to be used for the line. bandPlan997(1) is to be used for ITU-T G.993.1 Bandplan-B ETSI Bandplan ANSI Plan 997 bandPlan998(2) is to be used for ITU-T G.993.1 Bandplan-A ANSI Plan 998 bandPlanFx(3) is to be used for ITU-T G.993.1 Bandplan-C. other(4) is to be used for non-standard bandplans. If this object is set to bandPlanFx(3), then the object vdslLineConfBandPlanFx MUST also be set.rw
Enumeration
.1.3.6.1.2.1.10.97.1.1.11.1.31
vdslLineConfBandPlanFxThe frequency limit between bands D2 and U2 when vdslLineConfBandPlan is set to bandPlanFx(3).rw
Unsigned32
.1.3.6.1.2.1.10.97.1.1.11.1.32
vdslLineConfBandOptUsageDefines the VDSL link use of the optional frequency range [25kHz - 138kHz] (Opt). unused(1) indicates Opt is unused upstream(2) indicates Opt usage is for upstream downstream(3) indicates Opt usage is for downstream.rw
Enumeration
.1.3.6.1.2.1.10.97.1.1.11.1.33
vdslLineConfUpPsdTemplateThe upstream PSD template to be used for the line. Here, templateMask1(1) refers to a notched mask that limits the transmitted PSD within the internationally standardized HAM (Handheld Amateur Radio) radio bands, while templateMask2(2) refers to an unnotched mask. The masks themselves depend upon the applicable standard being used (vdslLineConfApplicableStandard).rw
Enumeration
.1.3.6.1.2.1.10.97.1.1.11.1.34
vdslLineConfDownPsdTemplateThe downstream PSD template to be used for the line. Here, templateMask1(1) refers to a notched mask that limits the transmitted PSD within the internationally standardized HAM (Handheld Amateur Radio) radio bands, while templateMask2(2) refers to an unnotched mask. The masks themselves depend upon the applicable standard being used (vdslLineConfApplicableStandard).rw
Enumeration
.1.3.6.1.2.1.10.97.1.1.11.1.35
vdslLineConfHamBandMaskThe transmit power spectral density mask code, used to avoid interference with HAM (Handheld Amateur Radio) radio bands by introducing power control (notching) in one or more of these bands. Amateur radio band notching is defined in the VDSL spectrum as follows: Band Start Frequency Stop Frequency ---- ------------------ -------------------------------- 30m 1810 kHz 2000 kHz 40m 3500 kHz 3800 kHz (ETSI); 4000 kHz (ANSI) 80m 7000 kHz 7100 kHz (ETSI); 7300 kHz (ANSI) 160m 10100 kHz 10150 kHz Notching for each standard band can be enabled or disabled via the bit mask. Two custom notches may be specified. If either of these are enabled via the bit mask, then the following objects MUST be specified: If customNotch1 is enabled, then both vdslLineConfCustomNotch1Start vdslLineConfCustomNotch1Stop MUST be specified. If customNotch2 is enabled, then both vdslLineConfCustomNotch2Start vdslLineConfCustomNotch2Stop MUST be specified.rw
Bits
.1.3.6.1.2.1.10.97.1.1.11.1.36
vdslLineConfCustomNotch1StartSpecifies the start frequency of custom HAM (Handheld Amateur Radio) notch 1. vdslLineConfCustomNotch1Start MUST be less than or equal to vdslLineConfCustomNotch1Stop.rw
Unsigned32 UNITS "kHz"
.1.3.6.1.2.1.10.97.1.1.11.1.37
vdslLineConfCustomNotch1StopSpecifies the stop frequency of custom HAM (Handheld Amateur Radio) notch 1. vdslLineConfCustomNotch1Stop MUST be greater than or equal to vdslLineConfCustomNotch1Start.rw
Unsigned32 UNITS "kHz"
.1.3.6.1.2.1.10.97.1.1.11.1.38
vdslLineConfCustomNotch2StartSpecifies the start frequency of custom HAM (Handheld Amateur Radio) notch 2. vdslLineConfCustomNotch2Start MUST be less than or equal to vdslLineConfCustomNotch2Stop.rw
Unsigned32 UNITS "kHz"
.1.3.6.1.2.1.10.97.1.1.11.1.39
vdslLineConfCustomNotch2StopSpecifies the stop frequency of custom HAM (Handheld Amateur Radio) notch 2. vdslLineConfCustomNotch2Stop MUST be greater than or equal to vdslLineConfCustomNotch2Start.rw
Unsigned32 UNITS "kHz"
.1.3.6.1.2.1.10.97.1.1.11.1.40
vdslLineConfDownTargetSlowBurstSpecifies the target level of impulse noise (burst) protection for an interleaved (slow) channel.rw
Unsigned32
.1.3.6.1.2.1.10.97.1.1.11.1.41
vdslLineConfUpTargetSlowBurstSpecifies the target level of impulse noise (burst) protection for an interleaved (slow) channel.rw
Unsigned32
.1.3.6.1.2.1.10.97.1.1.11.1.42
vdslLineConfDownMaxFastFecThis parameter provisions the maximum level of Forward Error Correction (FEC) redundancy related overhead to be maintained for a fast channel.rw
Unsigned32
.1.3.6.1.2.1.10.97.1.1.11.1.43
vdslLineConfUpMaxFastFecThis parameter provisions the maximum level of Forward Error Correction (FEC) redundancy related overhead to be maintained for a fast channel.rw
Unsigned32
.1.3.6.1.2.1.10.97.1.1.11.1.44
vdslLineConfLineTypeThis parameter provisions the VDSL physical entity at start-up by defining whether and how the line will be channelized, i.e., which channel type(s) are supported. If the line is to be channelized, the value will be other than noChannel(1). This configuration can be activated only during start-up. Afterwards, the value of vdslLineType coincides with the value of vdslLineConfLineType. Depending on this value, the corresponding entries in the ifTable for the interleaved and the fast channels are enabled or disabled according to the value of their ifOperStatus. Defined values are: noChannel(1) -- no channels exist fastOnly(2) -- only fast channel exists interleavedOnly(3) -- only interleaved channel exists fastOrInterleaved(4) -- either fast or interleaved channel -- exists, but only one at a time fastAndInterleaved(5) -- both fast and interleaved channels -- exist Note that 'slow' and 'interleaved' refer to the same channel.rw
Enumeration
.1.3.6.1.2.1.10.97.1.1.11.1.45
vdslLineConfProfRowStatusThis object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be first unreferenced from all associated lines. An 'active' profile may be modified at any time. Note that some changes may require that any referenced lines be restarted (e.g., vdslLineConfLineType).rw
RowStatus (SNMPv2-TC)
.1.3.6.1.2.1.10.97.1.1.11.1.46
vdslLineAlarmConfProfileTableThis table contains information on the VDSL line alarm configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the VDSL line alarm thresholds. Entries in this table MUST be maintained in a persistent manner.
SEQUENCE OF VdslLineAlarmConfProfileEntry
.1.3.6.1.2.1.10.97.1.1.20
vdslLineAlarmConfProfileEntryEach entry consists of a list of parameters that represents the configuration of a VDSL line alarm profile. A default profile with an index of 'DEFVAL', will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document.
VdslLineAlarmConfProfileEntry
.1.3.6.1.2.1.10.97.1.1.20.1
vdslLineAlarmConfProfileNameThe name for this profile as specified by an administrator.
SnmpAdminString
.1.3.6.1.2.1.10.97.1.1.20.1.1
vdslLineAlarmConfThresh15MinLofsThis object configures the threshold for the number of loss of frame seconds (lofs) within any given 15-minute performance data collection interval. If the value of loss of frame seconds in a particular 15-minute collection interval reaches/exceeds this value, a vdslPerfLofsThreshNotification notification will be generated. No more than one notification will be sent per interval.rw
HCPerfIntervalThreshold UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.20.1.2
vdslLineAlarmConfThresh15MinLossThis object configures the threshold for the number of loss of signal seconds (loss) within any given 15-minute performance data collection interval. If the value of loss of signal seconds in a particular 15-minute collection interval reaches/exceeds this value, a vdslPerfLossThreshNotification notification will be generated. One notification will be sent per interval per endpoint.rw
HCPerfIntervalThreshold UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.20.1.3
vdslLineAlarmConfThresh15MinLprsThis object configures the threshold for the number of loss of power seconds (lprs) within any given 15-minute performance data collection interval. If the value of loss of power seconds in a particular 15-minute collection interval reaches/exceeds this value, a vdslPerfLprsThreshNotification notification will be generated. No more than one notification will be sent per interval.rw
HCPerfIntervalThreshold UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.20.1.4
vdslLineAlarmConfThresh15MinLolsThis object configures the threshold for the number of loss of link seconds (lols) within any given 15-minute performance data collection interval. If the value of loss of power seconds in a particular 15-minute collection interval reaches/exceeds this value, a vdslPerfLolsThreshNotification notification will be generated. No more than one notification will be sent per interval.rw
HCPerfIntervalThreshold UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.20.1.5
vdslLineAlarmConfThresh15MinESsThis object configures the threshold for the number of errored seconds (ESs) within any given 15-minute performance data collection interval. If the value of errored seconds in a particular 15-minute collection interval reaches/exceeds this value, a vdslPerfESsThreshNotification notification will be generated. No more than one notification will be sent per interval.rw
HCPerfIntervalThreshold UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.20.1.6
vdslLineAlarmConfThresh15MinSESsThis object configures the threshold for the number of severely errored seconds (SESs) within any given 15-minute performance data collection interval. If the value of severely errored seconds in a particular 15-minute collection interval reaches/exceeds this value, a vdslPerfSESsThreshNotification notification will be generated. No more than one notification will be sent per interval.rw
HCPerfIntervalThreshold UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.20.1.7
vdslLineAlarmConfThresh15MinUASsThis object configures the threshold for the number of unavailable seconds (UASs) within any given 15-minute performance data collection interval. If the value of unavailable seconds in a particular 15-minute collection interval reaches/exceeds this value, a vdslPerfUASsThreshNotification notification will be generated. No more than one notification will be sent per interval.rw
HCPerfIntervalThreshold UNITS "seconds"
.1.3.6.1.2.1.10.97.1.1.20.1.8
vdslLineAlarmConfInitFailureThis object specifies if a vdslInitFailureNotification notification will be generated if an initialization failure occurs.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.2.1.10.97.1.1.20.1.9
vdslLineAlarmConfProfRowStatusThis object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service, (by setting this object to 'destroy' or 'outOfService') it must be first unreferenced from all associated lines. An 'active' profile may be modified at any time.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.2.1.10.97.1.1.20.1.10
vdslConformance
OBJECT IDENTIFIER
.1.3.6.1.2.1.10.97.1.3
vdslGroups
OBJECT IDENTIFIER
.1.3.6.1.2.1.10.97.1.3.1
vdslGroupA collection of objects providing information about a VDSL Line.
Unknown
.1.3.6.1.2.1.10.97.1.3.1.1
vdslNotificationGroupThis group supports notifications of significant conditions associated with VDSL Lines.
Unknown
.1.3.6.1.2.1.10.97.1.3.1.2
vdslCompliances
OBJECT IDENTIFIER
.1.3.6.1.2.1.10.97.1.3.2
vdslLineMibComplianceThe compliance statement for SNMP entities which manage VDSL interfaces.
Unknown
.1.3.6.1.2.1.10.97.1.3.2.1
VDSL-LINE-MIB - SNMP MIB Reference | MIBs Explorer