ZYXEL-ES3124PWR-MIB
Fault event table definitions
Main OID:
faultMIB.1.3.6.1.4.1.890.1.5.8.14.26
381
Objects
Active
Status
11
Dependencies
Imported Objects
Objects
381 total| Object Name |
|---|
zyxel OBJECT IDENTIFIER .1.3.6.1.4.1.890 |
RFC1155-SMI Unknown .1.3.6.1.4.1.890 |
SNMPv2-SMI NOTIFICATION-TYPE .1.3.6.1.4.1.890 |
products OBJECT IDENTIFIER .1.3.6.1.4.1.890.1 |
accessSwitch OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5 |
esSeries OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8 |
es3124pwr OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14 |
sysInfo OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.1 |
sysSwPlatformMajorVersSW platform major version, e.g. 3.ro INTEGER .1.3.6.1.4.1.890.1.5.8.14.1.1 |
sysSwPlatformMinorVersSW platform minor version, e.g. 50.ro INTEGER .1.3.6.1.4.1.890.1.5.8.14.1.2 |
sysSwModelStringModel letters, e.g. TJro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.1.3 |
sysSwVersionControlNbrVersion control number, e.g. 0.ro INTEGER .1.3.6.1.4.1.890.1.5.8.14.1.4 |
sysSwDaySW compilation day, e.g. 19.ro INTEGER .1.3.6.1.4.1.890.1.5.8.14.1.5 |
sysSwMonthSW compilation month, e.g. 8.ro INTEGER .1.3.6.1.4.1.890.1.5.8.14.1.6 |
sysSwYearSW compilation year, e.g. 2004.ro INTEGER .1.3.6.1.4.1.890.1.5.8.14.1.7 |
sysHwMajorVersHW major version number, e.g. 1.ro INTEGER .1.3.6.1.4.1.890.1.5.8.14.1.8 |
sysHwMinorVersHW minor version number, e.g. 0.ro INTEGER .1.3.6.1.4.1.890.1.5.8.14.1.9 |
sysSerialNumberSerial numberro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.1.10 |
rateLimitSetup OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.2 |
rateLimitStateIngress/egress rate limiting enabled/disabled for the switch.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.2.1 |
rateLimitPortTable SEQUENCE OF RateLimitPortEntry .1.3.6.1.4.1.890.1.5.8.14.2.2 |
rateLimitPortEntryAn entry in rateLimitPortTable. RateLimitPortEntry .1.3.6.1.4.1.890.1.5.8.14.2.2.1 |
rateLimitPortStateIngress/egress rate limiting enabled/disabled on the port.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.2.2.1.1 |
rateLimitPortIngRateIngress rate in Mbit/s. The granularity of FE port is between 1 and 100. For GE port, the granularity is between 1 and 1000.rw INTEGER .1.3.6.1.4.1.890.1.5.8.14.2.2.1.2 |
rateLimitPortEgrRateEgress rate in Mbit/s. The granularity of FE port is between 1 and 100. For GE port, the granularity is between 1 and 1000.rw INTEGER .1.3.6.1.4.1.890.1.5.8.14.2.2.1.3 |
brLimitSetup OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.3 |
brLimitStateBroadcast/multicast/DLF rate limiting enabled/disabled for the switch.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.3.1 |
brLimitPortTable SEQUENCE OF BrLimitPortEntry .1.3.6.1.4.1.890.1.5.8.14.3.2 |
brLimitPortEntryAn entry in brLimitPortTable. BrLimitPortEntry .1.3.6.1.4.1.890.1.5.8.14.3.2.1 |
brLimitPortBrStateBroadcast rate limiting enabled/disabled on the port.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.3.2.1.1 |
brLimitPortBrRateAllowed broadcast rate in pkts/s. For FE port,
the maximum value is 148800. For GE port, the maximum value is 262143.rw INTEGER .1.3.6.1.4.1.890.1.5.8.14.3.2.1.2 |
brLimitPortMcStateMulticast rate limiting enabled/disabled on the port.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.3.2.1.3 |
brLimitPortMcRateAAllowed mullticast rate in pkts/s. For FE port,
the maximum value is 148800. For GE port, the maximum value is 262143.rw INTEGER .1.3.6.1.4.1.890.1.5.8.14.3.2.1.4 |
brLimitPortDlfStateDestination lookup failure frames rate limiting enabled/disabled on the port.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.3.2.1.5 |
brLimitPortDlfRateAllowed destination lookup failure frames rate in pkts/s.
For FE port, the maximum value is 148800. For GE port, the maximum value is 262143.rw INTEGER .1.3.6.1.4.1.890.1.5.8.14.3.2.1.6 |
portSecuritySetup OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.4 |
portSecurityStaterw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.4.1 |
portSecurityPortTable SEQUENCE OF PortSecurityPortEntry .1.3.6.1.4.1.890.1.5.8.14.4.2 |
portSecurityPortEntryAn entry in portSecurityPortTable. PortSecurityPortEntry .1.3.6.1.4.1.890.1.5.8.14.4.2.1 |
portSecurityPortStatePort Security enabled/disabled on the port.
Active(1) means this port only accept frames from static MAC addresses that are configured for the port,
and dynamic MAC address frames up to the number specified by portSecurityPortCount object.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.4.2.1.1 |
portSecurityPortLearnStateMAC address learning enabled/disable on the port.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.4.2.1.2 |
portSecurityPortCountNumber of (dynamic) MAC addresses that may be learned on the port.rw INTEGER .1.3.6.1.4.1.890.1.5.8.14.4.2.1.3 |
portSecurityMacFreezeThis entry is used to execute MacFreeze action to port.
It's meaningless while reading this entry.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.4.3 |
vlanTrunkSetup OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.5 |
vlanTrunkPortTable SEQUENCE OF VlanTrunkPortEntry .1.3.6.1.4.1.890.1.5.8.14.5.1 |
vlanTrunkPortEntryAn entry in vlanTrunkPortTable. VlanTrunkPortEntry .1.3.6.1.4.1.890.1.5.8.14.5.1.1 |
vlanTrunkPortStateVlanTrunking enabled/disabled on the port.
Active(1) to allow frames belonging to unknown
VLAN groups to pass through the switch.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.5.1.1.1 |
ctlProtTransSetup OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.6 |
ctlProtTransStateBridge control protocol transparency enabled/disabled for the switchrw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.6.1 |
ctlProtTransTunnelPortTable SEQUENCE OF CtlProtTransTunnelPortEntry .1.3.6.1.4.1.890.1.5.8.14.6.2 |
ctlProtTransTunnelPortEntryAn entry in ctlProtTransTunnelPortTable. CtlProtTransTunnelPortEntry .1.3.6.1.4.1.890.1.5.8.14.6.2.1 |
ctlProtTransTunnelModeBridge control protocol transparency mode for the port.
Modes: Peer(0), Tunnel(1), Discard(2), Network(3)rw Enumeration .1.3.6.1.4.1.890.1.5.8.14.6.2.1.1 |
vlanStackSetup OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.7 |
vlanStackStateVLAN Stacking enabled/disabled for the switch.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.7.1 |
vlanStackTpidSP TPID in hex format, e.g. 8100.rw INTEGER .1.3.6.1.4.1.890.1.5.8.14.7.2 |
vlanStackPortTable SEQUENCE OF VlanStackPortEntry .1.3.6.1.4.1.890.1.5.8.14.7.3 |
vlanStackPortEntryAn entry in vlanStackPortTable. VlanStackPortEntry .1.3.6.1.4.1.890.1.5.8.14.7.3.1 |
vlanStackPortModeMode of the port. Set Normal to have the switch ignore frames received
(or transmitted) on this port with VLAN stacking tags.
Anything you configure in SPVID and Priority are ignored.
Set Access mode to have the switch add the SP TPID tag to all incoming
frames received on this port. Set Access mode for ingress ports at the
edge of the service provider's network. Set Tunnel mode (available for
Gigabit ports only) for egress ports at the edge of the service provider's
network. In order to support VLAN stacking on a port, the port must be able
to allow frames of 1526 Bytes (1522 Bytes + 4 Bytes for the second tag)
to pass through it. normal (1), Access (2), tunnel (3)rw Enumeration .1.3.6.1.4.1.890.1.5.8.14.7.3.1.1 |
vlanStackPortVidVLAN ID used in service provider tag.rw INTEGER .1.3.6.1.4.1.890.1.5.8.14.7.3.1.2 |
vlanStackPortPrioPriority value for service provider tag.
0 is the lowest priority level and 7 is the highest.rw Enumeration .1.3.6.1.4.1.890.1.5.8.14.7.3.1.3 |
radius8021xSetup OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.8 |
radiusLoginPrecedence1. Local Only
2. Local then RADIUS
3. RADIUS Onlyrw INTEGER .1.3.6.1.4.1.890.1.5.8.14.8.1 |
radiusAnd8021xServer OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.8.2 |
radiusIpAddrThe IP address of the RADIUS server.rw IpAddress .1.3.6.1.4.1.890.1.5.8.14.8.2.1 |
radiusUdpPortThe UDP port of the RADIUS server.rw INTEGER .1.3.6.1.4.1.890.1.5.8.14.8.2.2 |
radiusSharedSecretShared secret used for RADIUS and network eleemnt authentication.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.8.2.3 |
portAuthState802.1x port authentication enabled/disabled for the switch.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.8.3 |
portAuthTable SEQUENCE OF PortAuthEntry .1.3.6.1.4.1.890.1.5.8.14.8.4 |
portAuthEntryAn entry in portAuthTable. PortAuthEntry .1.3.6.1.4.1.890.1.5.8.14.8.4.1 |
portAuthEntryState802.1x port authentication enabled or disabled on the port.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.8.4.1.1 |
portReAuthEntryState802.1x port re-authentication enabled or disabled on the port.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.8.4.1.2 |
portReAuthEntryTimerRe-authentication timer in seconds.rw INTEGER .1.3.6.1.4.1.890.1.5.8.14.8.4.1.3 |
hwMonitorInfo OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.9 |
fanRpmTable SEQUENCE OF FanRpmEntry .1.3.6.1.4.1.890.1.5.8.14.9.1 |
fanRpmEntryAn entry in fanRpmTable. FanRpmEntry .1.3.6.1.4.1.890.1.5.8.14.9.1.1 |
fanRpmIndexIndex of FAN.ro INTEGER .1.3.6.1.4.1.890.1.5.8.14.9.1.1.1 |
fanRpmCurValueCurrent speed in Revolutions Per Minute (RPM) on the fan.ro INTEGER .1.3.6.1.4.1.890.1.5.8.14.9.1.1.2 |
fanRpmMaxValueMaximum speed measured in Revolutions Per Minute (RPM) on the fan.ro INTEGER .1.3.6.1.4.1.890.1.5.8.14.9.1.1.3 |
fanRpmMinValueMinimum speed measured in Revolutions Per Minute (RPM) on the fan.ro INTEGER .1.3.6.1.4.1.890.1.5.8.14.9.1.1.4 |
fanRpmLowThreshThe minimum speed at which a normal fan should work.ro INTEGER .1.3.6.1.4.1.890.1.5.8.14.9.1.1.5 |
fanRpmDescr'Normal' indicates that this fan is functioning above the minimum speed.
'Error' indicates that this fan is functioning below the minimum speed.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.9.1.1.6 |
tempTable SEQUENCE OF TempEntry .1.3.6.1.4.1.890.1.5.8.14.9.2 |
tempEntryAn entry in tempTable. TempEntry .1.3.6.1.4.1.890.1.5.8.14.9.2.1 |
tempIndexIndex of temperature unit. 1:MAC, 2:CPU, 3:PHYro Enumeration .1.3.6.1.4.1.890.1.5.8.14.9.2.1.1 |
tempCurValueThe current temperature measured at this sensor.ro INTEGER .1.3.6.1.4.1.890.1.5.8.14.9.2.1.2 |
tempMaxValueThe maximum temperature measured at this sensor.ro INTEGER .1.3.6.1.4.1.890.1.5.8.14.9.2.1.3 |
tempMinValueThe minimum temperature measured at this sensor.ro INTEGER .1.3.6.1.4.1.890.1.5.8.14.9.2.1.4 |
tempHighThreshThe upper temperature limit at this sensor.ro INTEGER .1.3.6.1.4.1.890.1.5.8.14.9.2.1.5 |
tempDescr'Normal' indicates temperatures below the threshold and 'Error' for those above.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.9.2.1.6 |
voltageTable SEQUENCE OF VoltageEntry .1.3.6.1.4.1.890.1.5.8.14.9.3 |
voltageEntryAn entry in voltageTable. VoltageEntry .1.3.6.1.4.1.890.1.5.8.14.9.3.1 |
voltageIndexIndex of voltage.ro INTEGER .1.3.6.1.4.1.890.1.5.8.14.9.3.1.1 |
voltageCurValueThe current voltage reading.ro INTEGER .1.3.6.1.4.1.890.1.5.8.14.9.3.1.2 |
voltageMaxValueThe maximum voltage measured at this point.ro INTEGER .1.3.6.1.4.1.890.1.5.8.14.9.3.1.3 |
voltageMinValueThe minimum voltage measured at this point.ro INTEGER .1.3.6.1.4.1.890.1.5.8.14.9.3.1.4 |
voltageNominalValueThe normal voltage at wchich the switch work.ro INTEGER .1.3.6.1.4.1.890.1.5.8.14.9.3.1.5 |
voltageLowThreshThe minimum voltage at which the switch should work.ro INTEGER .1.3.6.1.4.1.890.1.5.8.14.9.3.1.6 |
voltageDescr'Normal' indicates that the voltage is within an acceptable operating range
at this point; otherwise 'Error' is displayed.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.9.3.1.7 |
snmpSetup OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.10 |
snmpGetCommunityrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.10.1 |
snmpSetCommunityrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.10.2 |
snmpTrapCommunityrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.10.3 |
snmpTrapDestTable SEQUENCE OF SnmpTrapDestEntry .1.3.6.1.4.1.890.1.5.8.14.10.4 |
snmpTrapDestEntryAn entry in snmpTrapDestTable. SnmpTrapDestEntry .1.3.6.1.4.1.890.1.5.8.14.10.4.1 |
snmpTrapDestIPIP address of trap destination.rw IpAddress .1.3.6.1.4.1.890.1.5.8.14.10.4.1.1 |
snmpTrapDestRowStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.10.4.1.2 |
dateTimeServerSetup OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.11 |
dateTimeServerTypeThe time service protocol.rw Enumeration .1.3.6.1.4.1.890.1.5.8.14.11.1 |
dateTimeServerIPIP address of time server.rw IpAddress .1.3.6.1.4.1.890.1.5.8.14.11.2 |
dateTimeZoneThe time difference between UTC. Ex: +01rw INTEGER .1.3.6.1.4.1.890.1.5.8.14.11.3 |
dateTimeNewDateYearThe new date in year.rw INTEGER .1.3.6.1.4.1.890.1.5.8.14.11.4 |
dateTimeNewDateMonthThe new date in month.rw INTEGER .1.3.6.1.4.1.890.1.5.8.14.11.5 |
dateTimeNewDateDayThe new date in day.rw INTEGER .1.3.6.1.4.1.890.1.5.8.14.11.6 |
dateTimeNewTimeHourThe new time in hour.rw INTEGER .1.3.6.1.4.1.890.1.5.8.14.11.7 |
dateTimeNewTimeMinuteThe new time in minute.rw INTEGER .1.3.6.1.4.1.890.1.5.8.14.11.8 |
dateTimeNewTimeSecondThe new time in second.rw INTEGER .1.3.6.1.4.1.890.1.5.8.14.11.9 |
sysMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.12 |
sysMgmtConfigSaveIf setting value is given, the variable write index will be set and running-config will be written to the assigned configuration file.
If not, running-config will be written to the booting one.rw Enumeration .1.3.6.1.4.1.890.1.5.8.14.12.1 |
sysMgmtBootupConfigThe setting value (read index) will be written into non-volatile memory.
While rebooting, the variable write index is equal to read index initially.
You can change the value of write index by CLI / MIB.rw Enumeration .1.3.6.1.4.1.890.1.5.8.14.12.2 |
sysMgmtRebootReboot switch from SNMP. 1:Reboot, 0:Nothingrw Enumeration .1.3.6.1.4.1.890.1.5.8.14.12.3 |
sysMgmtDefaultConfigErase running config and reset to default.rw Enumeration .1.3.6.1.4.1.890.1.5.8.14.12.4 |
sysMgmtLastActionStatusDisplay status of last mgmt action.ro Enumeration .1.3.6.1.4.1.890.1.5.8.14.12.5 |
sysMgmtSystemStatusThis variable indicates the status of the system.
The sysMgmtAlarmStatus is a bit map represented
a sum, therefore, it can represent multiple defects
simultaneously. The sysNoDefect should be set if and only if
no other flag is set.
The various bit positions are:
0 sysAlarmDetected
1 sysTemperatureError
2 sysFanRPMError
3 sysVoltageRangeErrorro Bits .1.3.6.1.4.1.890.1.5.8.14.12.6 |
layer2Setup OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.13 |
vlanTypeSetuprw Enumeration .1.3.6.1.4.1.890.1.5.8.14.13.1 |
igmpSnoopingStateSetuprw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.13.2 |
tagVlanPortIsolationStaterw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.13.3 |
stpStaterw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.13.4 |
ipSetup OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.14 |
dnsIpAddressrw IpAddress .1.3.6.1.4.1.890.1.5.8.14.14.1 |
defaultMgmtrw Enumeration .1.3.6.1.4.1.890.1.5.8.14.14.2 |
inbandIpSetup OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.14.3 |
inbandIpTyperw Enumeration .1.3.6.1.4.1.890.1.5.8.14.14.3.1 |
inbandVidrw INTEGER .1.3.6.1.4.1.890.1.5.8.14.14.3.2 |
inbandStaticIprw IpAddress .1.3.6.1.4.1.890.1.5.8.14.14.3.3 |
inbandStaticSubnetMaskrw IpAddress .1.3.6.1.4.1.890.1.5.8.14.14.3.4 |
inbandStaticGatewayrw IpAddress .1.3.6.1.4.1.890.1.5.8.14.14.3.5 |
outOfBandIpSetup OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.14.4 |
outOfBandIprw IpAddress .1.3.6.1.4.1.890.1.5.8.14.14.4.1 |
outOfBandSubnetMaskrw IpAddress .1.3.6.1.4.1.890.1.5.8.14.14.4.2 |
outOfBandGatewayrw IpAddress .1.3.6.1.4.1.890.1.5.8.14.14.4.3 |
maxNumOfInbandIpro INTEGER .1.3.6.1.4.1.890.1.5.8.14.14.5 |
inbandIpTable SEQUENCE OF InbandIpEntry .1.3.6.1.4.1.890.1.5.8.14.14.6 |
inbandIpEntryAn entry in inbandIpTable. InbandIpEntry .1.3.6.1.4.1.890.1.5.8.14.14.6.1 |
inbandEntryIprw IpAddress .1.3.6.1.4.1.890.1.5.8.14.14.6.1.1 |
inbandEntrySubnetMaskrw IpAddress .1.3.6.1.4.1.890.1.5.8.14.14.6.1.2 |
inbandEntryGatewayrw IpAddress .1.3.6.1.4.1.890.1.5.8.14.14.6.1.3 |
inbandEntryVidrw INTEGER .1.3.6.1.4.1.890.1.5.8.14.14.6.1.4 |
inbandEntryManageablerw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.14.6.1.5 |
inbandEntryRowStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.14.6.1.6 |
filterSetup OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.15 |
filterTable SEQUENCE OF FilterEntry .1.3.6.1.4.1.890.1.5.8.14.15.1 |
filterEntryAn entry in filterTable. FilterEntry .1.3.6.1.4.1.890.1.5.8.14.15.1.1 |
filterNamerw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.15.1.1.1 |
filterActionStaterw Enumeration .1.3.6.1.4.1.890.1.5.8.14.15.1.1.2 |
filterMacAddr PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.15.1.1.3 |
filterVid INTEGER .1.3.6.1.4.1.890.1.5.8.14.15.1.1.4 |
filterRowStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.15.1.1.5 |
mirrorSetup OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.16 |
mirrorStaterw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.16.1 |
mirrorMonitorPortrw INTEGER .1.3.6.1.4.1.890.1.5.8.14.16.2 |
mirrorTable SEQUENCE OF MirrorEntry .1.3.6.1.4.1.890.1.5.8.14.16.3 |
mirrorEntryAn entry in mirrorTable. MirrorEntry .1.3.6.1.4.1.890.1.5.8.14.16.3.1 |
mirrorMirroredStaterw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.16.3.1.1 |
mirrorDirectionrw Enumeration .1.3.6.1.4.1.890.1.5.8.14.16.3.1.2 |
aggrSetup OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.17 |
aggrStaterw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.17.1 |
aggrSystemPriorityrw INTEGER .1.3.6.1.4.1.890.1.5.8.14.17.2 |
aggrGroupTable SEQUENCE OF AggrGroupEntry .1.3.6.1.4.1.890.1.5.8.14.17.3 |
aggrGroupEntryAn entry in aggrGroupTable. AggrGroupEntry .1.3.6.1.4.1.890.1.5.8.14.17.3.1 |
aggrGroupIndexro INTEGER .1.3.6.1.4.1.890.1.5.8.14.17.3.1.1 |
aggrGroupStaterw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.17.3.1.2 |
aggrGroupDynamicStaterw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.17.3.1.3 |
aggrPortTable SEQUENCE OF AggrPortEntry .1.3.6.1.4.1.890.1.5.8.14.17.4 |
aggrPortEntryAn entry in aggrPortTable. AggrPortEntry .1.3.6.1.4.1.890.1.5.8.14.17.4.1 |
aggrPortGrouprw Enumeration .1.3.6.1.4.1.890.1.5.8.14.17.4.1.1 |
aggrPortDynamicStateTimeoutrw INTEGER .1.3.6.1.4.1.890.1.5.8.14.17.4.1.2 |
accessCtlSetup OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.18 |
accessCtlTable SEQUENCE OF AccessCtlEntry .1.3.6.1.4.1.890.1.5.8.14.18.1 |
accessCtlEntryAn entry in accessCtlTable. AccessCtlEntry .1.3.6.1.4.1.890.1.5.8.14.18.1.1 |
accessCtlServicero Enumeration .1.3.6.1.4.1.890.1.5.8.14.18.1.1.1 |
accessCtlEnablerw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.18.1.1.2 |
accessCtlServicePortrw INTEGER .1.3.6.1.4.1.890.1.5.8.14.18.1.1.3 |
accessCtlTimeoutrw INTEGER .1.3.6.1.4.1.890.1.5.8.14.18.1.1.4 |
securedClientTable SEQUENCE OF SecuredClientEntry .1.3.6.1.4.1.890.1.5.8.14.18.2 |
securedClientEntryAn entry in securedClientTable. SecuredClientEntry .1.3.6.1.4.1.890.1.5.8.14.18.2.1 |
securedClientIndexro INTEGER .1.3.6.1.4.1.890.1.5.8.14.18.2.1.1 |
securedClientEnablerw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.18.2.1.2 |
securedClientStartIprw IpAddress .1.3.6.1.4.1.890.1.5.8.14.18.2.1.3 |
securedClientEndIprw IpAddress .1.3.6.1.4.1.890.1.5.8.14.18.2.1.4 |
securedClientServicerw Bits .1.3.6.1.4.1.890.1.5.8.14.18.2.1.5 |
queuingMethodSetup OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.19 |
queuingMethodTyperw Enumeration .1.3.6.1.4.1.890.1.5.8.14.19.1 |
portQueuingMethodTable SEQUENCE OF PortQueuingMethodEntry .1.3.6.1.4.1.890.1.5.8.14.19.2 |
portQueuingMethodEntryAn entry in portQueuingMethodTable. PortQueuingMethodEntry .1.3.6.1.4.1.890.1.5.8.14.19.2.1 |
portQueuingMethodQueue0...7ro INTEGER .1.3.6.1.4.1.890.1.5.8.14.19.2.1.1 |
portQueuingMethodWeight0...100rw INTEGER .1.3.6.1.4.1.890.1.5.8.14.19.2.1.2 |
dhcpSetup OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.20 |
dhcpRelay OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.20.1 |
dhcpRelayEnablerw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.20.1.1 |
dhcpRelayOption82Enablerw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.20.1.2 |
dhcpRelayInfoEnablerw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.20.1.3 |
dhcpRelayInfoDatarw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.20.1.4 |
maxNumberOfDhcpRemoteServerro INTEGER .1.3.6.1.4.1.890.1.5.8.14.20.1.5 |
dhcpRemoteServerTable SEQUENCE OF DhcpRemoteServerEntry .1.3.6.1.4.1.890.1.5.8.14.20.1.6 |
dhcpRemoteServerEntryAn entry in dhcpRemoteServerTable. DhcpRemoteServerEntry .1.3.6.1.4.1.890.1.5.8.14.20.1.6.1 |
dhcpRemoteServerIp IpAddress .1.3.6.1.4.1.890.1.5.8.14.20.1.6.1.1 |
dhcpRemoteServerRowStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.20.1.6.1.2 |
staticRouteSetup OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.21 |
maxNumberOfStaticRoutesro INTEGER .1.3.6.1.4.1.890.1.5.8.14.21.1 |
staticRouteTable SEQUENCE OF StaticRouteEntry .1.3.6.1.4.1.890.1.5.8.14.21.2 |
staticRouteEntryAn entry in staticRouteTable. StaticRouteEntry .1.3.6.1.4.1.890.1.5.8.14.21.2.1 |
staticRouteNamerw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.21.2.1.1 |
staticRouteIp IpAddress .1.3.6.1.4.1.890.1.5.8.14.21.2.1.2 |
staticRouteMask IpAddress .1.3.6.1.4.1.890.1.5.8.14.21.2.1.3 |
staticRouteGatewayrw IpAddress .1.3.6.1.4.1.890.1.5.8.14.21.2.1.4 |
staticRouteMetricrw INTEGER .1.3.6.1.4.1.890.1.5.8.14.21.2.1.5 |
staticRouteRowStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.21.2.1.6 |
arpInfo OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.22 |
arpTable SEQUENCE OF ArpEntry .1.3.6.1.4.1.890.1.5.8.14.22.1 |
arpEntryAn entry in arpTable. ArpEntry .1.3.6.1.4.1.890.1.5.8.14.22.1.1 |
arpIndexro INTEGER .1.3.6.1.4.1.890.1.5.8.14.22.1.1.1 |
arpIpAddrro IpAddress .1.3.6.1.4.1.890.1.5.8.14.22.1.1.2 |
arpMacAddrro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.22.1.1.3 |
arpMacVidro INTEGER .1.3.6.1.4.1.890.1.5.8.14.22.1.1.4 |
arpTypero INTEGER .1.3.6.1.4.1.890.1.5.8.14.22.1.1.5 |
pltMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.23 |
pltCtlTable SEQUENCE OF PltCtlEntry .1.3.6.1.4.1.890.1.5.8.14.23.1 |
pltCtlEntryAn entry in pltCtlTable. PltCtlEntry .1.3.6.1.4.1.890.1.5.8.14.23.1.1 |
pltCtlInstTypeThe type of the service instance that is tested.
1: VLAN Enumeration .1.3.6.1.4.1.890.1.5.8.14.23.1.1.1 |
pltCtlInstIdThe ID of the service instance that is tested. INTEGER .1.3.6.1.4.1.890.1.5.8.14.23.1.1.2 |
pltCtlIpAddrIP address of this PLT stack instance.rw IpAddress .1.3.6.1.4.1.890.1.5.8.14.23.1.1.3 |
pltCtlMaskIP subnet mask of this PLT stack instance.rw IpAddress .1.3.6.1.4.1.890.1.5.8.14.23.1.1.4 |
pltCtlGwDefault gateway IP address of this PLT stack instance.rw IpAddress .1.3.6.1.4.1.890.1.5.8.14.23.1.1.5 |
pltCtlRowStatusThis object allows entries to be created and deleted in the pltCtlTable.
All value MUST be specified prior to a transition to active(1) state being accepted.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.23.1.1.6 |
pingCtlTableDefines the ping Control Table for providing, via SNMP,
the capability of performing ping operations at
a remote host. The results of these operations are
stored in the pingResultsTable and the
pingProbeHistoryTable. SEQUENCE OF PingCtlEntry .1.3.6.1.4.1.890.1.5.8.14.23.2 |
pingCtlEntryDefines an entry in the pingCtlTable. The first index
element, pingCtlOwnerIndex, is of type SnmpAdminString,
a textual convention that allows for use of the SNMPv3
View-Based Access Control Model (RFC 2575 [11], VACM)
and allows an management application to identify its
entries. The second index, pingCtlTestName (also an
SnmpAdminString), enables the same management
application to have multiple outstanding requests. PingCtlEntry .1.3.6.1.4.1.890.1.5.8.14.23.2.1 |
pingCtlServInstTypeThe type of the service instance that this ping entry belong to.
1: VLAN.
This item would be used as an index Enumeration .1.3.6.1.4.1.890.1.5.8.14.23.2.1.1 |
pingCtlServInstIdThe ID of the service instance that this ping entry belong to.
This item would be used as an index INTEGER .1.3.6.1.4.1.890.1.5.8.14.23.2.1.2 |
pingCtlOwnerIndexTo facilitate the provisioning of access control by a
security administrator using the View-Based Access
Control Model (RFC 2575, VACM) for tables in which
multiple users may need to independently create or
modify entries, the initial index is used as an 'owner
index'. Such an initial index has a syntax of
SnmpAdminString, and can thus be trivially mapped to a
securityName or groupName as defined in VACM, in
accordance with a security policy.
When used in conjunction with such a security policy all
entries in the table belonging to a particular user (or
group) will have the same value for this initial index.
For a given user's entries in a particular table, the
object identifiers for the information in these entries
will have the same subidentifiers (except for the 'column'
subidentifier) up to the end of the encoded owner index.
To configure VACM to permit access to this portion of the
table, one would create vacmViewTreeFamilyTable entries
with the value of vacmViewTreeFamilySubtree including
the owner index portion, and vacmViewTreeFamilyMask
'wildcarding' the column subidentifier. More elaborate
configurations are possible. SnmpAdminString .1.3.6.1.4.1.890.1.5.8.14.23.2.1.3 |
pingCtlTestNameThe name of the ping test. This is locally unique, within
the scope of an pingCtlOwnerIndex. SnmpAdminString .1.3.6.1.4.1.890.1.5.8.14.23.2.1.4 |
pingCtlTargetAddressTypeSpecifies the type of host address to be used at a remote
host for performing a ping operation.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.8.14.23.2.1.5 |
pingCtlTargetAddressSpecifies the host address to be used at a remote host for
performing a ping operation. The host address type is
determined by the object value of corresponding
pingCtlTargetAddressType.
A value for this object MUST be set prior to transitioning
its corresponding pingCtlEntry to active(1) via
pingCtlRowStatus.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.8.14.23.2.1.6 |
pingCtlDataSizeSpecifies the size of the data portion to be
transmitted in a ping operation in octets. A ping
request is usually an ICMP message encoded
into an IP packet. An IP packet has a maximum size
of 65535 octets. Subtracting the size of the ICMP
or UDP header (both 8 octets) and the size of the IP
header (20 octets) yields a maximum size of 65507
octets.rw Unsigned32 .1.3.6.1.4.1.890.1.5.8.14.23.2.1.7 |
pingCtlTimeOutSpecifies the time-out value, in seconds, for a
remote ping operation.rw Unsigned32 .1.3.6.1.4.1.890.1.5.8.14.23.2.1.8 |
pingCtlProbeCountSpecifies the number of times to perform a ping
operation at a remote host.rw Unsigned32 .1.3.6.1.4.1.890.1.5.8.14.23.2.1.9 |
pingCtlAdminStatusReflects the desired state that a pingCtlEntry should be
in:
enabled(1) - Attempt to activate the test as defined by
this pingCtlEntry.
disabled(2) - Deactivate the test as defined by this
pingCtlEntry.
Refer to the corresponding pingResultsOperStatus to
determine the operational state of the test defined by
this entry.rw Enumeration .1.3.6.1.4.1.890.1.5.8.14.23.2.1.10 |
pingCtlDataFillThe content of this object is used together with the
corresponding pingCtlDataSize value to determine how to
fill the data portion of a probe packet. The option of
selecting a data fill pattern can be useful when links
are compressed or have data pattern sensitivities. The
contents of pingCtlDataFill should be repeated in a ping
packet when the size of the data portion of the ping
packet is greater than the size of pingCtlDataFill.rw OCTET STRING .1.3.6.1.4.1.890.1.5.8.14.23.2.1.11 |
pingCtlFrequencyThe number of seconds to wait before repeating a ping test
as defined by the value of the various objects in the
corresponding row.
A single ping test consists of a series of ping probes.
The number of probes is determined by the value of the
corresponding pingCtlProbeCount object. After a single
test completes the number of seconds as defined by the
value of pingCtlFrequency MUST elapse before the
next ping test is started.
A value of 0 for this object implies that the test
as defined by the corresponding entry will not be
repeated.rw Unsigned32 UNITS "seconds" .1.3.6.1.4.1.890.1.5.8.14.23.2.1.12 |
pingCtlMaxRowsThe maximum number of entries allowed in the
pingProbeHistoryTable. An implementation of this
MIB will remove the oldest entry in the
pingProbeHistoryTable to allow the addition of an
new entry once the number of rows in the
pingProbeHistoryTable reaches this value.
Old entries are not removed when a new test is
started. Entries are added to the pingProbeHistoryTable
until pingCtlMaxRows is reached before entries begin to
be removed.
A value of 0 for this object disables creation of
pingProbeHistoryTable entries.rw Unsigned32 UNITS "rows" .1.3.6.1.4.1.890.1.5.8.14.23.2.1.13 |
pingCtlStorageTypeThe storage type for this conceptual row.
Conceptual rows having the value 'permanent' need not
allow write-access to any columnar objects in the row.rw StorageType (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.23.2.1.14 |
pingCtlTrapGenerationThe value of this object determines when and if
to generate a notification for this entry:
probeFailure(0) - Generate a pingProbeFailed
notification subject to the value of
pingCtlTrapProbeFailureFilter. The object
pingCtlTrapProbeFailureFilter can be used
to specify the number of successive probe failures
that are required before a pingProbeFailed
notification can be generated.
testFailure(1) - Generate a pingTestFailed
notification. In this instance the object
pingCtlTrapTestFailureFilter can be used to
determine the number of probe failures that
signal when a test fails.
testCompletion(2) - Generate a pingTestCompleted
notification.
The value of this object defaults to zero, indicating
that none of the above options have been selected.rw Bits .1.3.6.1.4.1.890.1.5.8.14.23.2.1.15 |
pingCtlTrapProbeFailureFilterThe value of this object is used to determine when
to generate a pingProbeFailed NOTIFICATION.
Setting pingCtlTrapGeneration
to probeFailure(0) implies that a pingProbeFailed
NOTIFICATION is generated only when the number of
successive probe failures as indicated by the
value of pingCtlTrapPrbefailureFilter fail within
a given ping test.rw Unsigned32 .1.3.6.1.4.1.890.1.5.8.14.23.2.1.16 |
pingCtlTrapTestFailureFilterThe value of this object is used to determine when
to generate a pingTestFailed NOTIFICATION.
Setting pingCtlTrapGeneration to testFailure(1)
implies that a pingTestFailed NOTIFICATION is
generated only when the number of ping failures
within a test exceed the value of
pingCtlTrapTestFailureFilter.rw Unsigned32 .1.3.6.1.4.1.890.1.5.8.14.23.2.1.17 |
pingCtlTypeThe value of this object is used to either report or
select the implementation method to be used for
calculating a ping response time. The value of this
object MAY be selected from pingImplementationTypeDomains.
Additional implementation types SHOULD be allocated as
required by implementers of the DISMAN-PING-MIB under
their enterprise specific registration point and not
beneath pingImplementationTypeDomains.rw OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.23.2.1.18 |
pingCtlDescrThe purpose of this object is to provide a
descriptive name of the remote ping test.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.890.1.5.8.14.23.2.1.19 |
pingCtlSourceAddressTypeSpecifies the type of the source address,
pingCtlSourceAddress, to be used at a remote host
when performing a ping operation.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.8.14.23.2.1.20 |
pingCtlSourceAddressUse the specified IP address (which must be given
in numeric form, not as a hostname) as the source
address in outgoing probe packets. On hosts with
more than one IP address, this option can be used
to force the source address to be something other
than the primary IP address of the interface the
probe packet is sent on. If the IP address is not
one of this machine's interface addresses, an error
is returned and nothing is sent. A zero length
octet string value for this object disables source
address specification.
The address type (InetAddressType) that relates to
this object is specified by the corresponding value
of pingCtlSourceAddressType.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.8.14.23.2.1.21 |
pingCtlIfIndexSetting this object to an interface's ifIndex prior
to starting a remote ping operation directs
the ping probes to be transmitted over the
specified interface. A value of zero for this object
means that this option is not enabled.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.890.1.5.8.14.23.2.1.22 |
pingCtlByPassRouteTableThe purpose of this object is to optionally enable
bypassing the route table. If enabled, the remote
host will bypass the normal routing tables and send
directly to a host on an attached network. If the
host is not on a directly-attached network, an
error is returned. This option can be used to perform
the ping operation to a local host through an
interface that has no route defined (e.g., after the
interface was dropped by routed).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.23.2.1.23 |
pingCtlDSFieldSpecifies the value to store in the Differentiated
Services (DS) Field in the IP packet used to
encapsulate the ping probe. The DS Field is defined
as the Type of Service (TOS) octet in a IPv4 header
or as the Traffic Class octet in a IPv6 header.
The value of this object must be a decimal integer
in the range from 0 to 255. This option can be used
to determine what effect an explicit DS Field setting
has on a ping response. Not all values are legal or
meaningful. A value of 0 means that the function
represented by this option is not supported. DS Field
usage is often not supported by IP implementations and
not all values are supported. Refer to RFC 2474 for
guidance on usage of this field.rw Unsigned32 .1.3.6.1.4.1.890.1.5.8.14.23.2.1.24 |
pingCtlRowStatusThis object allows entries to be created and deleted
in the pingCtlTable. Deletion of an entry in this
table results in all corresponding (same
pingCtlOwnerIndex and pingCtlTestName index values)
pingResultsTable and pingProbeHistoryTable entries
being deleted.
A value MUST be specified for pingCtlTargetAddress
prior to a transition to active(1) state being
accepted.
Activation of a remote ping operation is controlled
via pingCtlAdminStatus and not by changing
this object's value to active(1).
Transitions in and out of active(1) state are not
allowed while an entry's pingResultsOperStatus is
active(1) with the exception that deletion of
an entry in this table by setting its RowStatus
object to destroy(6) will stop an active
ping operation.
The operational state of a ping operation
can be determined by examination of its
pingResultsOperStatus object.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.23.2.1.25 |
pingResultsTableDefines the Ping Results Table for providing
the capability of performing ping operations at
a remote host. The results of these operations are
stored in the pingResultsTable and the pingPastProbeTable.
An entry is added to the pingResultsTable when an
pingCtlEntry is started by successful transition
of its pingCtlAdminStatus object to enabled(1).
An entry is removed from the pingResultsTable when
its corresponding pingCtlEntry is deleted. SEQUENCE OF PingResultsEntry .1.3.6.1.4.1.890.1.5.8.14.23.3 |
pingResultsEntryDefines an entry in the pingResultsTable. The
pingResultsTable has the same indexing as the
pingCtlTable in order for a pingResultsEntry to
correspond to the pingCtlEntry that caused it to
be created. PingResultsEntry .1.3.6.1.4.1.890.1.5.8.14.23.3.1 |
pingResultsOperStatusReflects the operational state of a pingCtlEntry:
enabled(1) - Test is active.
disabled(2) - Test has stopped.ro Enumeration .1.3.6.1.4.1.890.1.5.8.14.23.3.1.1 |
pingResultsIpTargetAddressTypeThis objects indicates the type of address stored
in the corresponding pingResultsIpTargetAddress
object.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.8.14.23.3.1.2 |
pingResultsIpTargetAddressThis objects reports the IP address associated
with a pingCtlTargetAddress value when the destination
address is specified as a DNS name. The value of
this object should be a zero length octet string
when a DNS name is not specified or when a
specified DNS name fails to resolve.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.8.14.23.3.1.3 |
pingResultsMinRttThe minimum ping round-trip-time (RTT) received. A value
of 0 for this object implies that no RTT has been received.ro Unsigned32 UNITS "milliseconds" .1.3.6.1.4.1.890.1.5.8.14.23.3.1.4 |
pingResultsMaxRttThe maximum ping round-trip-time (RTT) received. A value
of 0 for this object implies that no RTT has been received.ro Unsigned32 UNITS "milliseconds" .1.3.6.1.4.1.890.1.5.8.14.23.3.1.5 |
pingResultsAverageRttThe current average ping round-trip-time (RTT).ro Unsigned32 UNITS "milliseconds" .1.3.6.1.4.1.890.1.5.8.14.23.3.1.6 |
pingResultsProbeResponsesNumber of responses received for the corresponding
pingCtlEntry and pingResultsEntry. The value of this object
MUST be reported as 0 when no probe responses have been
received.ro Unsigned32 UNITS "responses" .1.3.6.1.4.1.890.1.5.8.14.23.3.1.7 |
pingResultsSentProbesThe value of this object reflects the number of probes sent
for the corresponding pingCtlEntry and pingResultsEntry.
The value of this object MUST be reported as 0 when no probes
have been sent.ro Unsigned32 UNITS "probes" .1.3.6.1.4.1.890.1.5.8.14.23.3.1.8 |
pingResultsRttSumOfSquaresThis object contains the sum of the squares for all ping
responses received. Its purpose is to enable standard
deviation calculation. The value of this object MUST
be reported as 0 when no ping responses have been
received.ro Unsigned32 UNITS "milliseconds" .1.3.6.1.4.1.890.1.5.8.14.23.3.1.9 |
pingResultsLastGoodProbeDate and time when the last response was received for
a probe.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.23.3.1.10 |
pingProbeHistoryTableDefines a table for storing the results of a ping
operation. Entries in this table are limited by
the value of the corresponding pingCtlMaxRows
object.
An entry in this table is created when the result of
a ping probe is determined. The initial 2 instance
identifier index values identify the pingCtlEntry
that a probe result (pingProbeHistoryEntry) belongs
to. An entry is removed from this table when
its corresponding pingCtlEntry is deleted.
An implementation of this MIB will remove the oldest
entry in the pingProbeHistoryTable to allow the
addition of an new entry once the number of rows in
the pingProbeHistoryTable reaches the value specified
by pingCtlMaxRows. SEQUENCE OF PingProbeHistoryEntry .1.3.6.1.4.1.890.1.5.8.14.23.4 |
pingProbeHistoryEntryDefines an entry in the pingProbeHistoryTable.
The first two index elements identify the
pingCtlEntry that a pingProbeHistoryEntry belongs
to. The third index element selects a single
probe result. PingProbeHistoryEntry .1.3.6.1.4.1.890.1.5.8.14.23.4.1 |
pingProbeHistoryIndexAn entry in this table is created when the result of
a ping probe is determined. The initial 2 instance
identifier index values identify the pingCtlEntry
that a probe result (pingProbeHistoryEntry) belongs
to.
An implementation MUST start assigning
pingProbeHistoryIndex values at 1 and wrap after
exceeding the maximum possible value as defined by
the limit of this object ('ffffffff'h). Unsigned32 (1..'ffffffff'h) .1.3.6.1.4.1.890.1.5.8.14.23.4.1.1 |
pingProbeHistoryResponseThe amount of time measured in milliseconds from when
a probe was sent to when its response was received or
when it timed out. The value of this object is reported
as 0 when it is not possible to transmit a probe.ro Unsigned32 UNITS "milliseconds" .1.3.6.1.4.1.890.1.5.8.14.23.4.1.2 |
pingProbeHistoryStatusThe result of a particular probe done by a remote host.ro OperationResponseStatus (DISMAN-PING-MIB) .1.3.6.1.4.1.890.1.5.8.14.23.4.1.3 |
pingProbeHistoryLastRCThe last implementation method specific reply code received.
If the ICMP Echo capability is being used then a successful
probe ends when an ICMP response is received that contains
the code ICMP-ECHOREPLY(0). The ICMP responses are defined
normally in the ip-icmp include file.ro Integer32 .1.3.6.1.4.1.890.1.5.8.14.23.4.1.4 |
pingProbeHistoryTimeTimestamp for when this probe result was determined.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.23.4.1.5 |
traceRouteCtlTableDefines the Remote Operations Traceroute Control Table for
providing the capability of invoking traceroute from a remote
host. The results of traceroute operations can be stored in
the traceRouteResultsTable, traceRouteProbeHistoryTable, and
the traceRouteHopsTable. SEQUENCE OF TraceRouteCtlEntry .1.3.6.1.4.1.890.1.5.8.14.23.5 |
traceRouteCtlEntryDefines an entry in the traceRouteCtlTable. The first
index element, traceRouteCtlOwnerIndex, is of type
SnmpAdminString, a textual convention that allows for
use of the SNMPv3 View-Based Access Control Model
(RFC 2575 [11], VACM) and allows an management
application to identify its entries. The second index,
traceRouteCtlTestName (also an SnmpAdminString),
enables the same management application to have
multiple requests outstanding. TraceRouteCtlEntry .1.3.6.1.4.1.890.1.5.8.14.23.5.1 |
traceRouteCtlServInstTypeThe type of the service instance that this traceRoute entry belong to.
1: VLAN.
This item would be used as an index Enumeration .1.3.6.1.4.1.890.1.5.8.14.23.5.1.1 |
traceRouteCtlServInstIdThe ID of the service instance that this traceRoute entry belong to.
This item would be used as an index INTEGER .1.3.6.1.4.1.890.1.5.8.14.23.5.1.2 |
traceRouteCtlOwnerIndexTo facilitate the provisioning of access control by a
security administrator using the View-Based Access
Control Model (RFC 2575, VACM) for tables in which
multiple users may need to independently create or
modify entries, the initial index is used as an 'owner
index'. Such an initial index has a syntax of
SnmpAdminString, and can thus be trivially mapped to a
securityName or groupName as defined in VACM, in
accordance with a security policy.
When used in conjunction with such a security policy
all entries in the table belonging to a particular user
(or group) will have the same value for this initial
index. For a given user's entries in a particular
table, the object identifiers for the information in
these entries will have the same subidentifiers (except
for the 'column' subidentifier) up to the end of the
encoded owner index. To configure VACM to permit access
to this portion of the table, one would create
vacmViewTreeFamilyTable entries with the value of
vacmViewTreeFamilySubtree including the owner index
portion, and vacmViewTreeFamilyMask 'wildcarding' the
column subidentifier. More elaborate configurations
are possible. SnmpAdminString .1.3.6.1.4.1.890.1.5.8.14.23.5.1.3 |
traceRouteCtlTestNameThe name of a traceroute test. This is locally unique,
within the scope of an traceRouteCtlOwnerIndex. SnmpAdminString .1.3.6.1.4.1.890.1.5.8.14.23.5.1.4 |
traceRouteCtlTargetAddressTypeSpecifies the type of host address to be used on the
traceroute request at the remote host.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.8.14.23.5.1.5 |
traceRouteCtlTargetAddressSpecifies the host address used on the
traceroute request at the remote host. The
host address type can be determined by the
examining the value of the corresponding
traceRouteCtlTargetAddressType index element.
A value for this object MUST be set prior to
transitioning its corresponding traceRouteCtlEntry to
active(1) via traceRouteCtlRowStatus.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.8.14.23.5.1.6 |
traceRouteCtlByPassRouteTableThe purpose of this object is to optionally enable
bypassing the route table. If enabled, the remote
host will bypass the normal routing tables and send
directly to a host on an attached network. If the
host is not on a directly-attached network, an
error is returned. This option can be used to perform
the traceroute operation to a local host through an
interface that has no route defined (e.g., after the
interface was dropped by routed).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.23.5.1.7 |
traceRouteCtlDataSizeSpecifies the size of the data portion of a traceroute
request in octets. A traceroute request is essentially
transmitted by encoding a UDP datagram into a
IP packet. So subtracting the size of a UDP header
(8 octets) and the size of a IP header (20 octets)
yields a maximum of 65507 octets.rw Unsigned32 .1.3.6.1.4.1.890.1.5.8.14.23.5.1.8 |
traceRouteCtlTimeOutSpecifies the time-out value, in seconds, for
a traceroute request.rw Unsigned32 .1.3.6.1.4.1.890.1.5.8.14.23.5.1.9 |
traceRouteCtlProbesPerHopSpecifies the number of times to reissue a traceroute
request with the same time-to-live (TTL) value.rw Unsigned32 .1.3.6.1.4.1.890.1.5.8.14.23.5.1.10 |
traceRouteCtlPortSpecifies the UDP port to send the traceroute
request to. Need to specify a port that is not in
use at the destination (target) host. The default
value for this object is the IANA assigned port,
33434, for the traceroute function.rw Unsigned32 .1.3.6.1.4.1.890.1.5.8.14.23.5.1.11 |
traceRouteCtlMaxTtlSpecifies the maximum time-to-live value.rw Unsigned32 .1.3.6.1.4.1.890.1.5.8.14.23.5.1.12 |
traceRouteCtlDSFieldSpecifies the value to store in the Differentiated
Services (DS) Field in the IP packet used to
encapsulate the traceroute probe. The DS Field is
defined as the Type of Service (TOS) octet in a IPv4
header or as the Traffic Class octet in a IPv6 header.
The value of this object must be a decimal integer
in the range from 0 to 255. This option can be used
to determine what effect an explicit DS Field setting
has on a traceroute response. Not all values are legal
or meaningful. DS Field usage is often not supported
by IP implementations. A value of 0 means that the
function represented by this option is not supported.
Useful TOS octet values are probably '16' (low delay)
and '8' ( high throughput).rw Unsigned32 .1.3.6.1.4.1.890.1.5.8.14.23.5.1.13 |
traceRouteCtlSourceAddressTypeSpecifies the type of the source address,
traceRouteCtlSourceAddress, to be used at a remote host
when performing a traceroute operation.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.8.14.23.5.1.14 |
traceRouteCtlSourceAddressUse the specified IP address (which must be given
as an IP number, not a hostname) as the source
address in outgoing probe packets. On hosts with
more than one IP address, this option can be used
to force the source address to be something other
than the primary IP address of the interface the
probe packet is sent on. If the IP address is not
one of this machine's interface addresses, an error
is returned and nothing is sent. A zero length
octet string value for this object disables source
address specification.
The address type (InetAddressType) that relates to
this object is specified by the corresponding value
of traceRouteCtlSourceAddressType.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.8.14.23.5.1.15 |
traceRouteCtlIfIndexSetting this object to an interface's ifIndex prior
to starting a remote traceroute operation directs
the traceroute probes to be transmitted over the
specified interface. A value of zero for this object
implies that this option is not enabled.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.890.1.5.8.14.23.5.1.16 |
traceRouteCtlMiscOptionsEnables an application to specify implementation
dependent options.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.890.1.5.8.14.23.5.1.17 |
traceRouteCtlMaxFailuresThe value of this object indicates the maximum number
of consecutive timeouts allowed before terminating
a remote traceroute request. A value of either 255 (maximum
hop count/possible TTL value) or a 0 indicates that the
function of terminating a remote traceroute request when a
specific number of successive timeouts are detected is
disabled.rw Unsigned32 .1.3.6.1.4.1.890.1.5.8.14.23.5.1.18 |
traceRouteCtlDontFragmentThis object enables setting of the don't fragment flag (DF)
in the IP header for a probe. Use of this object enables
performing a manual PATH MTU test.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.23.5.1.19 |
traceRouteCtlInitialTtlThe value of this object specifies the initial TTL value to
use. This enables bypassing the initial (often well known)
portion of a path.rw Unsigned32 .1.3.6.1.4.1.890.1.5.8.14.23.5.1.20 |
traceRouteCtlFrequencyThe number of seconds to wait before repeating a
traceroute test as defined by the value of the
various objects in the corresponding row.
The number of hops in a single traceroute test
is determined by the value of the corresponding
traceRouteCtlProbesPerHop object. After a
single test completes the number of seconds as defined
by the value of traceRouteCtlFrequency MUST elapse
before the next traceroute test is started.
A value of 0 for this object implies that the test
as defined by the corresponding entry will not be
repeated.rw Unsigned32 UNITS "seconds" .1.3.6.1.4.1.890.1.5.8.14.23.5.1.21 |
traceRouteCtlStorageTypeThe storage type for this conceptual row.
Conceptual rows having the value 'permanent' need not
allow write-access to any columnar objects in the row.rw StorageType (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.23.5.1.22 |
traceRouteCtlAdminStatusReflects the desired state that an traceRouteCtlEntry
should be in:
enabled(1) - Attempt to activate the test as defined by
this traceRouteCtlEntry.
disabled(2) - Deactivate the test as defined by this
traceRouteCtlEntry.
Refer to the corresponding traceRouteResultsOperStatus to
determine the operational state of the test defined by
this entry.rw Enumeration .1.3.6.1.4.1.890.1.5.8.14.23.5.1.23 |
traceRouteCtlDescrThe purpose of this object is to provide a
descriptive name of the remote traceroute
test.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.890.1.5.8.14.23.5.1.24 |
traceRouteCtlMaxRowsThe maximum number of entries allowed in the
traceRouteProbeHistoryTable. An implementation of
this MIB will remove the oldest entry in the
traceRouteProbeHistoryTable to allow the addition
of an new entry once the number of rows in the
traceRouteProbeHistoryTable reaches this value.
Old entries are not removed when a new test is
started. Entries are added to the
traceRouteProbeHistoryTable until traceRouteCtlMaxRows
is reached before entries begin to be removed.
A value of 0 for this object disables creation of
traceRouteProbeHistoryTable entries.rw Unsigned32 UNITS "rows" .1.3.6.1.4.1.890.1.5.8.14.23.5.1.25 |
traceRouteCtlTrapGenerationThe value of this object determines when and if to
to generate a notification for this entry:
pathChange(0) - Generate a traceRoutePathChange
notification when the current path varies from a
previously determined path.
testFailure(1) - Generate a traceRouteTestFailed
notification when the full path to a target
can't be determined.
testCompletion(2) - Generate a traceRouteTestCompleted
notification when the path to a target has been
determined.
The value of this object defaults to zero, indicating
that none of the above options have been selected.rw Bits .1.3.6.1.4.1.890.1.5.8.14.23.5.1.26 |
traceRouteCtlCreateHopsEntriesThe current path for a traceroute test is kept in the
traceRouteHopsTable on a per hop basis when the value of
this object is true(1).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.23.5.1.27 |
traceRouteCtlTypeThe value of this object is used either to report or
select the implementation method to be used for
performing a traceroute operation. The value of this
object may be selected from
traceRouteImplementationTypeDomains.
Additional implementation types should be allocated as
required by implementers of the DISMAN-TRACEROUTE-MIB
under their enterprise specific registration point and
not beneath traceRouteImplementationTypeDomains.rw OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.23.5.1.28 |
traceRouteCtlRowStatusThis object allows entries to be created and deleted
in the traceRouteCtlTable. Deletion of an entry in
this table results in all corresponding (same
traceRouteCtlOwnerIndex and traceRouteCtlTestName
index values) traceRouteResultsTable,
traceRouteProbeHistoryTable, and traceRouteHopsTable
entries being deleted.
A value MUST be specified for traceRouteCtlTargetAddress
prior to a transition to active(1) state being
accepted.
Activation of a remote traceroute operation is
controlled via traceRouteCtlAdminStatus and not
by transitioning of this object's value to active(1).
Transitions in and out of active(1) state are not
allowed while an entry's traceRouteResultsOperStatus
is active(1) with the exception that deletion of
an entry in this table by setting its RowStatus
object to destroy(6) will stop an active
traceroute operation.
The operational state of an traceroute operation
can be determined by examination of the corresponding
traceRouteResultsOperStatus object.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.23.5.1.29 |
traceRouteResultsTableDefines the Remote Operations Traceroute Results Table for
keeping track of the status of a traceRouteCtlEntry.
An entry is added to the traceRouteResultsTable when an
traceRouteCtlEntry is started by successful transition
of its traceRouteCtlAdminStatus object to enabled(1).
An entry is removed from the traceRouteResultsTable when
its corresponding traceRouteCtlEntry is deleted. SEQUENCE OF TraceRouteResultsEntry .1.3.6.1.4.1.890.1.5.8.14.23.6 |
traceRouteResultsEntryDefines an entry in the traceRouteResultsTable. The
traceRouteResultsTable has the same indexing as the
traceRouteCtlTable in order for a traceRouteResultsEntry
to correspond to the traceRouteCtlEntry that caused it to
be created. TraceRouteResultsEntry .1.3.6.1.4.1.890.1.5.8.14.23.6.1 |
traceRouteResultsOperStatusReflects the operational state of an traceRouteCtlEntry:
enabled(1) - Test is active.
disabled(2) - Test has stopped.ro Enumeration .1.3.6.1.4.1.890.1.5.8.14.23.6.1.1 |
traceRouteResultsCurHopCountReflects the current TTL value (range from 1 to
255) for a remote traceroute operation.
Maximum TTL value is determined by
traceRouteCtlMaxTtl.ro Gauge32 UNITS "hops" .1.3.6.1.4.1.890.1.5.8.14.23.6.1.2 |
traceRouteResultsCurProbeCountReflects the current probe count (1..10) for
a remote traceroute operation. The maximum
probe count is determined by
traceRouteCtlProbesPerHop.ro Gauge32 UNITS "probes" .1.3.6.1.4.1.890.1.5.8.14.23.6.1.3 |
traceRouteResultsIpTgtAddrTypeThis objects indicates the type of address stored
in the corresponding traceRouteResultsIpTgtAddr
object.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.8.14.23.6.1.4 |
traceRouteResultsIpTgtAddrThis objects reports the IP address associated
with a traceRouteCtlTargetAddress value when the
destination address is specified as a DNS name.
The value of this object should be a zero length
octet string when a DNS name is not specified or
when a specified DNS name fails to resolve.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.8.14.23.6.1.5 |
traceRouteResultsTestAttemptsThe current number of attempts to determine a path
to a target. The value of this object MUST be started
at 0.ro Unsigned32 UNITS "tests" .1.3.6.1.4.1.890.1.5.8.14.23.6.1.6 |
traceRouteResultsTestSuccessesThe current number of attempts to determine a path
to a target that have succeeded. The value of this
object MUST be reported as 0 when no attempts have
succeeded.ro Unsigned32 UNITS "tests" .1.3.6.1.4.1.890.1.5.8.14.23.6.1.7 |
traceRouteResultsLastGoodPathThe date and time when the last complete path
was determined.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.23.6.1.8 |
traceRouteProbeHistoryTableDefines the Remote Operations Traceroute Results Table for
storing the results of a traceroute operation.
An implementation of this MIB will remove the oldest
entry in the traceRouteProbeHistoryTable to allow the
addition of an new entry once the number of rows in
the traceRouteProbeHistoryTable reaches the value specified
by traceRouteCtlMaxRows. SEQUENCE OF TraceRouteProbeHistoryEntry .1.3.6.1.4.1.890.1.5.8.14.23.7 |
traceRouteProbeHistoryEntryDefines a table for storing the results of a traceroute
operation. Entries in this table are limited by
the value of the corresponding traceRouteCtlMaxRows
object.
The first two index elements identify the
traceRouteCtlEntry that a traceRouteProbeHistoryEntry
belongs to. The third index element selects a single
traceroute operation result. The fourth and fifth indexes
select the hop and the probe for a particular
traceroute operation. TraceRouteProbeHistoryEntry .1.3.6.1.4.1.890.1.5.8.14.23.7.1 |
traceRouteProbeHistoryIndexAn entry in this table is created when the result of
a traceroute probe is determined. The initial 2 instance
identifier index values identify the traceRouteCtlEntry
that a probe result (traceRouteProbeHistoryEntry) belongs
to. An entry is removed from this table when
its corresponding traceRouteCtlEntry is deleted.
An implementation MUST start assigning
traceRouteProbeHistoryIndex values at 1 and wrap after
exceeding the maximum possible value as defined by the
limit of this object ('ffffffff'h). Unsigned32 (1..'ffffffff'h) .1.3.6.1.4.1.890.1.5.8.14.23.7.1.1 |
traceRouteProbeHistoryHopIndexIndicates which hop in a traceroute path that the probe's
results are for. The value of this object is initially
determined by the value of traceRouteCtlInitialTtl. Unsigned32 .1.3.6.1.4.1.890.1.5.8.14.23.7.1.2 |
traceRouteProbeHistoryProbeIndexIndicates the index of a probe for a particular
hop in a traceroute path. The number of probes per
hop is determined by the value of the corresponding
traceRouteCtlProbesPerHop object. Unsigned32 .1.3.6.1.4.1.890.1.5.8.14.23.7.1.3 |
traceRouteProbeHistoryHAddrTypeThis objects indicates the type of address stored
in the corresponding traceRouteProbeHistoryHAddr
object.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.8.14.23.7.1.4 |
traceRouteProbeHistoryHAddrThe address of a hop in a traceroute path. This object
is not allowed to be a DNS name. The value of the
corresponding object, traceRouteProbeHistoryHAddrType,
indicates this object's IP address type.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.8.14.23.7.1.5 |
traceRouteProbeHistoryResponseThe amount of time measured in milliseconds from when
a probe was sent to when its response was received or
when it timed out. The value of this object is reported
as 0 when it is not possible to transmit a probe.ro Unsigned32 UNITS "milliseconds" .1.3.6.1.4.1.890.1.5.8.14.23.7.1.6 |
traceRouteProbeHistoryStatusThe result of a traceroute operation made by a remote
host for a particular probe.ro OperationResponseStatus (DISMAN-PING-MIB) .1.3.6.1.4.1.890.1.5.8.14.23.7.1.7 |
traceRouteProbeHistoryLastRCThe last implementation method specific reply code received.
Traceroute is usually implemented by transmitting a series of
probe packets with increasing time-to-live values. A probe
packet is a UDP datagram encapsulated into an IP packet.
Each hop in a path to the target (destination) host rejects
the probe packets (probe's TTL too small, ICMP reply) until
either the maximum TTL is exceeded or the target host is
received.ro Integer32 .1.3.6.1.4.1.890.1.5.8.14.23.7.1.8 |
traceRouteProbeHistoryTimeTimestamp for when this probe results were determined.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.23.7.1.9 |
traceRouteHopsTableDefines the Remote Operations Traceroute Hop Table for
keeping track of the results of traceroute tests on a
per hop basis. SEQUENCE OF TraceRouteHopsEntry .1.3.6.1.4.1.890.1.5.8.14.23.8 |
traceRouteHopsEntryDefines an entry in the traceRouteHopsTable.
The first two index elements identify the
traceRouteCtlEntry that a traceRouteHopsEntry
belongs to. The third index element,
traceRouteHopsHopIndex, selects a
hop in a traceroute path. TraceRouteHopsEntry .1.3.6.1.4.1.890.1.5.8.14.23.8.1 |
traceRouteHopsHopIndexSpecifies the hop index for a traceroute hop. Values
for this object with respect to the same
traceRouteCtlOwnerIndex and traceRouteCtlTestName
MUST start at 1 and increase monotonically.
The traceRouteHopsTable keeps the current traceroute
path per traceRouteCtlEntry if enabled by
setting the corresponding traceRouteCtlCreateHopsEntries
to true(1).
All hops (traceRouteHopsTable entries) in a traceroute
path MUST be updated at the same time when a traceroute
operation completes. Care needs to be applied when either
a path changes or can't be determined. The initial portion
of the path, up to the first hop change, MUST retain the
same traceRouteHopsHopIndex values. The remaining portion
of the path SHOULD be assigned new traceRouteHopsHopIndex
values. Unsigned32 .1.3.6.1.4.1.890.1.5.8.14.23.8.1.1 |
traceRouteHopsIpTgtAddressTypeThis objects indicates the type of address stored
in the corresponding traceRouteHopsIpTargetAddress
object.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.8.14.23.8.1.2 |
traceRouteHopsIpTgtAddressThis object reports the IP address associated with
the hop. A value for this object should be reported
as a numeric IP address and not as a DNS name.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.890.1.5.8.14.23.8.1.3 |
traceRouteHopsMinRttThe minimum traceroute round-trip-time (RTT) received for
this hop. A value of 0 for this object implies that no
RTT has been received.ro Unsigned32 .1.3.6.1.4.1.890.1.5.8.14.23.8.1.4 |
traceRouteHopsMaxRttThe maximum traceroute round-trip-time (RTT) received for
this hop. A value of 0 for this object implies that no
RTT has been received.ro Unsigned32 .1.3.6.1.4.1.890.1.5.8.14.23.8.1.5 |
traceRouteHopsAverageRttThe current average traceroute round-trip-time (RTT) for
this hop.ro Unsigned32 .1.3.6.1.4.1.890.1.5.8.14.23.8.1.6 |
traceRouteHopsRttSumOfSquaresThis object contains the sum of all traceroute responses
received for this hop. Its purpose is to enable standard
deviation calculation.ro Unsigned32 .1.3.6.1.4.1.890.1.5.8.14.23.8.1.7 |
traceRouteHopsSentProbesThe value of this object reflects the number of probes sent
for this hop during this traceroute test. The value of this
object should start at 0.ro Unsigned32 .1.3.6.1.4.1.890.1.5.8.14.23.8.1.8 |
traceRouteHopsProbeResponsesNumber of responses received for this hop during this
traceroute test. This value of this object should start
at 0.ro Unsigned32 .1.3.6.1.4.1.890.1.5.8.14.23.8.1.9 |
traceRouteHopsLastGoodProbeDate and time was the last response was received for a probe
for this hop during this traceroute test.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.23.8.1.10 |
portOpModeSetup OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.24 |
portOpModePortTable SEQUENCE OF PortOpModePortEntry .1.3.6.1.4.1.890.1.5.8.14.24.1 |
portOpModePortEntryAn entry in portOpModePortTable. PortOpModePortEntry .1.3.6.1.4.1.890.1.5.8.14.24.1.1 |
portOpModePortSpeedDuplexrw Enumeration .1.3.6.1.4.1.890.1.5.8.14.24.1.1.1 |
portOpModePortFlowCntlrw Enumeration .1.3.6.1.4.1.890.1.5.8.14.24.1.1.2 |
portOpModePortNamerw OCTET STRING .1.3.6.1.4.1.890.1.5.8.14.24.1.1.3 |
portOpModePortModuleTypero Enumeration .1.3.6.1.4.1.890.1.5.8.14.24.1.1.4 |
portOpModePortLinkUpTypero Enumeration .1.3.6.1.4.1.890.1.5.8.14.24.1.1.5 |
portOpModePortIntrusionLockrw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.24.1.1.6 |
portOpModePortLBTestStatusThis entry display latest loopback test status of port while performing loopback test.ro Enumeration .1.3.6.1.4.1.890.1.5.8.14.24.1.1.7 |
portBasedVlanSetup OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.25 |
portBasedVlanPortListTable SEQUENCE OF PortBasedVlanPortListEntry .1.3.6.1.4.1.890.1.5.8.14.25.1 |
portBasedVlanPortListEntryAn entry in portBasedVlanPortListTable. PortBasedVlanPortListEntry .1.3.6.1.4.1.890.1.5.8.14.25.1.1 |
portBasedVlanPortListMembersrw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.890.1.5.8.14.25.1.1.1 |
faultMIBFault event table definitions MODULE-IDENTITY .1.3.6.1.4.1.890.1.5.8.14.26 |
eventObjects OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.26.1 |
eventTableA list of currently active fault events. All faults
of normal type regardless of their severity level
are recorded in the event table. When a normal
type fault is cleared it is deleted from the event
table. SEQUENCE OF EventEntry .1.3.6.1.4.1.890.1.5.8.14.26.1.1 |
eventEntryAn entry containing information about an
event in the event table. EventEntry .1.3.6.1.4.1.890.1.5.8.14.26.1.1.1 |
eventSeqNumThis variable represents the sequence number of an event.
Sequence number is incremented monotonically starting
from 0 until it reaches its maximum and wraps around back
to 0.
Sequence number is incremented when
- the state of a normal type fault is set on (the same sequence
number is present in the events table as well as in the trap
that is sent to notify about the fault on event)
- delta event occurs (sequence number present in trap message)
- the state of a normal type fault is set off (sequence number
present in trap that is sent to notify for clearing).ro Integer32 .1.3.6.1.4.1.890.1.5.8.14.26.1.1.1.1 |
eventEventIdThis variable represents the event ID which uniquely
identifies the event in the entire system.ro EventIdNumber .1.3.6.1.4.1.890.1.5.8.14.26.1.1.1.2 |
eventNameThis variable represents the name of the event, for
example 'Ethernet Link Down'ro DisplayString .1.3.6.1.4.1.890.1.5.8.14.26.1.1.1.3 |
eventInstanceTypeThis variable represents the type of InstanceId of a
particular event in the event table. In brief
the instanceType refers to the type of sub-component
generating this event in the system, for example
switch (5). For more details see the textual
conventions section.
AFFECTS: eventInstanceId,
eventInstanceNamero InstanceType .1.3.6.1.4.1.890.1.5.8.14.26.1.1.1.4 |
eventInstanceIdThis variable represents the InstanceId of a particular
event in the event current table. In brief the instanceId
refers to the sub-component generating this event in the
system, for example '1' for port 1. For more details see
the textual conventions section.
DEPENDS ON: eventInstanceTypero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.26.1.1.1.5 |
eventInstanceNameThis variable is mainly used to store additional information
about the sub-component that is generating an event. For
example this field may specify what cooling fan is faulty.
DEPENDS ON: eventInstanceTypero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.890.1.5.8.14.26.1.1.1.6 |
eventSeverityThis variable dictates the urgency of action when a event
occurs. There are four severity levels - Critical, Major,
Minor, and Informational. Critical events are those, which
require immediate operator intervention to prevent/reduce
system down time. Major events require quick attention and
Minor events possibly require some attention. Informational
events indicate the occurrence of events that may need to be
investigated.ro EventSeverity .1.3.6.1.4.1.890.1.5.8.14.26.1.1.1.7 |
eventSetTimeThis table contains only normal events and this variable
represents the time when the event become active, i.e. the
number of seconds since Jan 1, 1970 12:00AM.ro UtcTimeStamp .1.3.6.1.4.1.890.1.5.8.14.26.1.1.1.8 |
eventDescriptionThis variable contains a description of the event and reasons
behind the event. This is a free format alpha-numeric string
that is set by the entity generating this event. This variable
may be empty if there is no usefull information to report.
The maximum length of this string is 255 characters.ro DisplayString .1.3.6.1.4.1.890.1.5.8.14.26.1.1.1.9 |
eventServAffectiveThis variable indicates whether the event is service affective or notro EventServiceAffective .1.3.6.1.4.1.890.1.5.8.14.26.1.1.1.10 |
faultTrapsMIBFault event trap definitions MODULE-IDENTITY .1.3.6.1.4.1.890.1.5.8.14.27 |
trapInfoObjects OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.27.1 |
trapRefSeqNumIndicates the former sequence number of a cleared event
in the event table. Not intended to read but only used in
trap notifications.ro Integer32 .1.3.6.1.4.1.890.1.5.8.14.27.1.1 |
trapPersistenceIndicates whether the event is delta (automatically and
immediately cleared) or normal (not automatically cleared).
Not intended to read but only used in trap notifications.ro EventPersistence .1.3.6.1.4.1.890.1.5.8.14.27.1.2 |
trapSenderNodeIdRepresents the node ID of the sending network element. If not
supported should be set to 0. Not intended to read but only
used in trap notifications.ro Integer32 .1.3.6.1.4.1.890.1.5.8.14.27.1.3 |
trapNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.5.8.14.27.2 |
eventOnTrapThis trap is used to inform network management system that a delta
fault event (events that are automatically cleared) has occured
or a normal fault event (not automatically cleared) state has
been set on.
Objects are used as follows:
- eventSeqNum is the sequence number of the event. For normal
type of events must equal to the sequence number of the event
in the events table.
- eventEventId specifies what fault event has occured.
- eventName specifies the name of the fault event.
- eventSetTime indicates when fault event has occured
(delta events) or when fault has been set on (normal events).
- eventSeverity reports the severity level of the event.
- eventInstanceType indicates what kind of object is faulty.
- eventInstanceId specifies what instance is faulty.
- eventInstanceName may contain textual description for
the faulty object.
- eventServAffective specifies whether the event is
immediately service affcetive.
- eventDescription reports possible additional information about the event.
- trapPersistence tells whether this event is a delta or normal event.
- trapSenderNodeId specifies the node ID of the sending network element if
configuring it is supported for the network element, otherwise 0.
- sysObjectID specifies what kind of equipment reports the fault event.
For more information see the eventTable specification NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.8.14.27.2.1 |
eventClearedTrapThis trap is used to inform network management system that a normal
type fault event has been cleared (state set off).
Objects are used as follows:
- eventSeqNum is the sequence number of the this clearing event. Note that
the sequence number of the cleared event is reported in the trapRefSeqNum
object.
- eventEventId specifies what event has been cleared.
- eventSetTime indicates when fault event has been cleared.
- eventInstanceType indicates what kind of object has been
faulty.
- eventInstanceId specifies what instance has been faulty.
- trapRefSeqNum specifies the sequence number of the cleared event (i.e.
the sequence number was assigned for the event in the events table).
- trapSenderNodeId specifies the node ID of the sending network element if
configuring it is supported for the network element, otherwise 0.
- sysObjectID specifies what kind of equipment reports the clearing event.
For more information see the eventTable specification NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.5.8.14.27.2.2 |