ZYXEL-ERR-DISABLE-MIB
AI MIB Summary
The ZYXEL-ERR-DISABLE-MIB provides management access to the errdisable state and recovery status of ports on ZyXEL network devices, enabling monitoring of interface shutdowns triggered by security violations or link faults.
The subtree for errdisable
Main OID:
zyxelErrdisable.1.3.6.1.4.1.890.1.15.3.24
30
Objects
Active
Status
14
Dependencies
Imported Objects
Objects
30 total| Object Name |
|---|
zyxelErrdisableThe subtree for errdisable MODULE-IDENTITY .1.3.6.1.4.1.890.1.15.3.24 |
RFC1155-SMIThe subtree for errdisable Unknown .1.3.6.1.4.1.890.1.15.3.24 |
IF-MIBThe subtree for errdisable NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.15.3.24 |
zyxelErrdisableSetup OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.15.3.24.1 |
zyxelErrdisableRecovery OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.15.3.24.1.1 |
zyErrdisableRecoveryStateEnable/Disable error disabled port recovery feature on the switch. Some features,
such as loop guard, allow the switch to shut down a port when an error is detected on the port.
For example, if the switch detects that packets sent out the port(s) loop back to the switch,
the switch can shut down the port(s) automatically. After that, you need to enable the port(s) manually.
With disabled port recovery, you can set the disabled port(s) to become active again after the time interval you specify.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.15.3.24.1.1.1 |
zyxelErrdisableRecoveryReasonTableThe table contains errdisable recovery reason configuration. SEQUENCE OF ZyxelErrdisableRecoveryReasonEntry .1.3.6.1.4.1.890.1.15.3.24.1.1.2 |
zyxelErrdisableRecoveryReasonEntryAn entry contains errdisable recovery reason configuration. ZyxelErrdisableRecoveryReasonEntry .1.3.6.1.4.1.890.1.15.3.24.1.1.2.1 |
zyErrdisableRecoveryReasonTypeThis entry displays the supported features that allow the switch to shut down
a port or discard packets on a port according to the feature requirements and
what action you configure. Enumeration .1.3.6.1.4.1.890.1.15.3.24.1.1.2.1.1 |
zyErrdisableRecoveryReasonStateEnable/Disable this entry to allow/prohibit the switch to activate a port
after the specified time interval, which is shut down by the supported feature.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.15.3.24.1.1.2.1.2 |
zyErrdisableRecoveryReasonIntervalEnter the number of seconds (from 30 to 2592000) for the switch to wait before
enabling the port which was shut down.rw INTEGER .1.3.6.1.4.1.890.1.15.3.24.1.1.2.1.3 |
zyxelErrdisableDetect OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.15.3.24.1.2 |
zyxelErrdisableDetectReasonTableThe table contains errdisable detect reason configuration. SEQUENCE OF ZyxelErrdisableDetectReasonEntry .1.3.6.1.4.1.890.1.15.3.24.1.2.1 |
zyxelErrdisableDetectReasonEntryAn entry contains errdisable detect reason configuration. ZyxelErrdisableDetectReasonEntry .1.3.6.1.4.1.890.1.15.3.24.1.2.1.1 |
zyErrdisableDetectReasonTypeThis field displays the type of control packets that may cause CPU overload. Enumeration .1.3.6.1.4.1.890.1.15.3.24.1.2.1.1.1 |
zyErrdisableDetectReasonStateEnable/Disable the detection on switch to monitor if the configured rate limit for a specific
control packet is exceeded and take the mode selected below.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.890.1.15.3.24.1.2.1.1.2 |
zyErrdisableDetectReasonModeSelect the mode that the switch takes when the number of control packets exceeds the rate limit on a port, set in the CPU protection.
inactive-port - The switch disables the port on which the control packets are received.
inactive-reason - The switch bypasses the processing of the specified control packets (such as ARP or IGMP packets), or drops all the specified control packets (such as BPDU) on the port.
rate-limitation - The switch drops the additional control packets the port has to handle in every one second.rw Enumeration .1.3.6.1.4.1.890.1.15.3.24.1.2.1.1.3 |
zyxelErrdisableStatus OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.15.3.24.2 |
zyxelErrdisableRecoveryTableThe table contains errdisable recovery information. SEQUENCE OF ZyxelErrdisableRecoveryEntry .1.3.6.1.4.1.890.1.15.3.24.2.1 |
zyxelErrdisableRecoveryEntryAn entry contains errdisable recovery information. ZyxelErrdisableRecoveryEntry .1.3.6.1.4.1.890.1.15.3.24.2.1.1 |
zyErrdisableRecoveryTypeThis field displays the supported features that allow the switch to shut down a port or
discard packets on a port according to the feature requirements and what action you configure. Enumeration .1.3.6.1.4.1.890.1.15.3.24.2.1.1.1 |
zyErrdisableRecoveryPortThis field displays which port(s) are shut down or discard packets by above reason. INTEGER .1.3.6.1.4.1.890.1.15.3.24.2.1.1.2 |
zyErrdisableRecoveryTimeToRecoverThis field displays how long (seconds) those ports will be re-activated.ro INTEGER .1.3.6.1.4.1.890.1.15.3.24.2.1.1.3 |
zyxelErrdisableTrapInfoObject OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.15.3.24.3 |
zyErrdisableTrapPortThis trap displays error disable detect on which port(s) by reason below.ro INTEGER .1.3.6.1.4.1.890.1.15.3.24.3.1 |
zyErrdisableTrapReasonTypeThis trap displays which port(s) are shut down or discard packets by mode below.ro Enumeration .1.3.6.1.4.1.890.1.15.3.24.3.2 |
zyErrdisableTrapModeThis trap displays which error disable mode on this port.ro Enumeration .1.3.6.1.4.1.890.1.15.3.24.3.3 |
zyxelErrdisableNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.890.1.15.3.24.4 |
zyErrdisableDetectThe trap is sent when an error is detected on a port, such as a loop occurs or the rate limit for
specific control packets is exceeded. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.15.3.24.4.1 |
zyErrdisableRecoveryThis trap is sent when the switch ceases the action taken on a port, such as shutting down
the port or discarding packets on the port, after the specified recovery interval. NOTIFICATION-TYPE .1.3.6.1.4.1.890.1.15.3.24.4.2 |