VERTICALT1-E1-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for VERTICALT1-E1-MIB.
64
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
64 total| Object Name |
|---|
vertical OBJECT IDENTIFIER .1.3.6.1.4.1.2338 |
RFC1213-MIB Unknown .1.3.6.1.4.1.2338 |
vdsx1TrunkRedClearThis notification is sent when the specific
trunk RED alarm condition clears. TRAP-TYPE .1.3.6.1.4.1.2338.0.1 |
vdsx1TrunkRedThis notification is sent when the specific
trunk goes into the RED alarm situation. Red
alarm condition signifies LOS (Loss of Signal)
failure, i.e. the receiver sees no positive or
negative pulses TRAP-TYPE .1.3.6.1.4.1.2338.0.2 |
vdsx1TrunkYellowClearThis notification is sent when the specific
trunk YELLOW alarm condition clears. TRAP-TYPE .1.3.6.1.4.1.2338.0.3 |
vdsx1TrunkYellowThis notification is sent when the specific
trunk goes into the YELLOW alarm situation.
Yellow alarm condition signifies a LOF (Loss
of Frame) condition, i.e. the receiver does not
see the expected framing pattern. TRAP-TYPE .1.3.6.1.4.1.2338.0.4 |
vdsx1TrunkBlueClearThis notification is sent when the specific
trunk BLUE alarm condition clears. TRAP-TYPE .1.3.6.1.4.1.2338.0.5 |
vdsx1TrunkBlueThis notification is sent when the specific
trunk goes into the BLUE alarm situation. Blue alarm
conditions occurs when the source goes into AIS (Alarm
indication Signal) state. This means that the source has
a problem that prevents it from sending its normal, framed
payload. Instead, it sends an unframed stream of 1's. TRAP-TYPE .1.3.6.1.4.1.2338.0.6 |
vdsx1TrunkReconfigCompleteThis notification is sent when the specific
trunk successfully reads and incorporates the
values from the registry. This is typically done
in response to a SET command on any of the Trunk's (or
its channel's) read-write parameters TRAP-TYPE .1.3.6.1.4.1.2338.0.7 |
vdsx1TrunkReconfigErrorThis notification is sent when the specific
trunk fails to incorporate the values read from
the registry. Typically, the trunk tries to re-read
the registry values in response to a SET command on
any of the Trunk's (or its channel's) read-write parameters TRAP-TYPE .1.3.6.1.4.1.2338.0.8 |
vdsx1TrunkLoopbackPayloadOnThis notification is sent when the specific
trunk enters a payload loopback state. Payload loopback means that
the received signal at this interface is looped through the
device. Typically the received signal is looped back for re-
transmission after it has passed through the device's framing function TRAP-TYPE .1.3.6.1.4.1.2338.0.43 |
vdsx1TrunkLoopbackPayloadOffThis notification is sent when the specific
trunk moves from a payload loopback state to a
non loopback state. TRAP-TYPE .1.3.6.1.4.1.2338.0.44 |
vdsx1TrunkLoopbackLineOnThis notification is sent when the specific
trunk enters a line loopback state. Under this state the received
signal at this interface does not go through the device
(minimum penetration) but is looped back out. TRAP-TYPE .1.3.6.1.4.1.2338.0.45 |
vdsx1TrunkLoopbackLineOffThis notification is sent when the specific
trunk goes out of a Line Looped state TRAP-TYPE .1.3.6.1.4.1.2338.0.46 |
vds1 OBJECT IDENTIFIER .1.3.6.1.4.1.2338.3 |
vdsx1CardTableThe Vertical DS1 Configuration table extension. SEQUENCE OF VDsx1CardEntry .1.3.6.1.4.1.2338.3.1 |
vdsx1CardEntryAn entry in the Vertical Card Configuration
table (an extension to the rfc1406 Configuration
table. VDsx1CardEntry .1.3.6.1.4.1.2338.3.1.1 |
vdsx1cardSlotNumberPhysical slot in the system in which the
card is installed.ro INTEGER .1.3.6.1.4.1.2338.3.1.1.1 |
vdsx1cardTypeThe Vertical's card Type. The following types are defined:
cardTYPE-DUAL-T1 = 1,
cardTYPE-8-CHANNEL-CO-POTS = 3,
cardTYPE-BRIDGE1 = 4,
cardTYPE-NOT-CONFIGURED = 100ro Enumeration .1.3.6.1.4.1.2338.3.1.1.2 |
vdsx1cardDescrVertical card identification number.ro INTEGER .1.3.6.1.4.1.2338.3.1.1.3 |
vdsx1cardRevisionVertical card revision level.ro INTEGER .1.3.6.1.4.1.2338.3.1.1.4 |
vdsx1cardDriverVersionVertical card driver version.ro INTEGER .1.3.6.1.4.1.2338.3.1.1.5 |
vdsx1cardIOPortAddressThe ISA bus base address for this Card.ro INTEGER (0..'7fffffff'h) .1.3.6.1.4.1.2338.3.1.1.6 |
vdsx1cardErrorLEDAll Vertical cards have an ERROR LED and
a READY LED. The combined values of these
LEDs are as follows -
ERRORLed READYLed VALUE OPERATIONAL DEFINITION
OFF OFF (0 0) Invalid state
ON OFF (1 0) Just after power up. This state
remains until card is
ready to service io.
ON ON (1 1) Statue during software initialization
OFF ON (0 1) The normal operational state
of the card.ro INTEGER .1.3.6.1.4.1.2338.3.1.1.7 |
vdsx1cardReadyLEDAll Vertical cards have a READY LED and
an ERROR LED. The combined values of these
LEDs are as follows -
ERRORLed READYLed OPERATIONAL DEFINITION
OFF OFF invalid state
ON OFF Just after power up. This
state remains until card is
ready to service io.
ON ON Statue during software initialization
OFF ON The normal operational state of the card.ro INTEGER .1.3.6.1.4.1.2338.3.1.1.8 |
vdsx1TrunkTableThe DS1 Trunk table extensions for
Vertical Networks Instant Office. SEQUENCE OF VDsx1TrunkEntry .1.3.6.1.4.1.2338.3.2 |
vdsx1TrunkEntryAn entry in the Vertical DS1 Trunk table VDsx1TrunkEntry .1.3.6.1.4.1.2338.3.2.1 |
vdsx1TrunkIfIndexThe interface Index for this trunk. The value for this object
is equal to the value of dsx1IfIndex from the Interfaces
table of DS1/E1 (RFC 1406). Which also correlates to the
IfIndex found in MIB-II.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.2338.3.2.1.1 |
vdsx1TrunkIndexThis object is the index into the number
of trunks associated with the card defined
in the card group.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.2338.3.2.1.2 |
vdsx1TrunkIdentifierThis value for this object is equal to the
value of dsx1CircuitIdentifier
from the Configuration table of
DS1/E1 (RFC 1406). This is a vendor specific
field used to help identify each specific
interface for diagnostic purposes.ro DisplayString .1.3.6.1.4.1.2338.3.2.1.3 |
vdsx1TrunkSlotNumberThe value for this object is the
logical number of the slot in which the
card containing this trunk is located, (vdsx1cardSlotNumber).ro INTEGER .1.3.6.1.4.1.2338.3.2.1.4 |
vdsx1TrunkDeviceNumberThe value for this object is the logical device number of
this trunk within its slot. This number may be used to
identify this device in the registry.ro INTEGER .1.3.6.1.4.1.2338.3.2.1.5 |
vdsx1TrunkInterruptInterrupt Request level for this card/trunk.
Note: all trunks in the same card have the same IRQ.ro INTEGER .1.3.6.1.4.1.2338.3.2.1.6 |
vdsx1TrunkEnabledSetting this variable to Deactivated will
disable this particular trunk.rw Enumeration .1.3.6.1.4.1.2338.3.2.1.7 |
vdsx1TrunkMasterPriorityDesignates the priority for selecting
which trunk is to drive the MVIP SEC8K
clock, i.e. which trunk drives the master
timing system. This value must be diffrent
for each Trunk in the system.Valid values
mean:
notUsed (100)=> never choose this trunk as clock master
primary (1)=> choose this trunk as first choice
firstAlternate (2)=> choose this trunk as second choice
secondAlternate (3)=> choose this trunk as third choicerw Enumeration .1.3.6.1.4.1.2338.3.2.1.8 |
vdsx1TrunkStreamThe MVIP Stream assigned to the Trunk.ro INTEGER .1.3.6.1.4.1.2338.3.2.1.9 |
vdsx1TrunkStartingChannelThe starting MVIP channel within the MVIP Stream.
If CardType is DTM or WAN1, this value is 0; if
CardType is CO-POTS, this value is 16 or 24.ro INTEGER .1.3.6.1.4.1.2338.3.2.1.10 |
vdsx1TrunkTypeSpecifies the TrunkType for this trunk.
Defines E1 vs T1 as well as Common
Channel Signalling (CCS) vs. Channel
Associated Signalling (CAS). Valid values
are :
dev-undef, // 100 : undefined
dev-t1CAS, // 1 : T1 Channel Associated Signaling
dev-t1CCS, // 2 : T1 Common Channel Signaling : with D channel
dev-coPots, // 7 : CO Pots (analog)ro Enumeration .1.3.6.1.4.1.2338.3.2.1.11 |
vdsx1TrunkIsdnSignalingProtocolDefines the switch type for the Isdn
protocol stack. The following are all the
possible types:
other(1), none of the following
ess4(5), U.S.A. / AT&T 4ESS
ess5(6), U.S.A. / AT&T 5ESS
dms100(7), U.S.A. / Northern Telecom DMS100
ni2(10), U.S.A. / National ISDN 2 (BRI, PRI)
dms100s100 (263) NT DMS-100 switch / S-100rw Enumeration .1.3.6.1.4.1.2338.3.2.1.12 |
vdsx1TrunkLineCodingLine Coding, i.e. the zero code suppression
used for this Trunk. Valid values are:
b8ZS (2) -> use of a specified pattern of
normal bits and bipolar violations
which are used to replace a sequence
of eight zero bits.
aMI (5) -> a mode wherein no zero code suppression
is present
other (6) -> none of the codes described above, or Not
Applicable, whichever is appropriate
Presently, T1 trunk can be either
b8zs (2) or ami (5).
E1 trunk must be hdb3 (3).rw Enumeration .1.3.6.1.4.1.2338.3.2.1.13 |
vdsx1TrunkFramingDefines framing for Trunk. T1 trunk can be either esf (2)
or d4 (3). E1 trunk can be either e1-crc (5) or e1-mf (6).
In cases where Framing is not applicable, value 1 (other) would
be displayed.rw Enumeration .1.3.6.1.4.1.2338.3.2.1.14 |
vdsx1TrunkDChannelSlotSlot number of trunk whose DChannel controls the B channels
of this trunk.rw INTEGER .1.3.6.1.4.1.2338.3.2.1.15 |
vdsx1TrunkDChannelDeviceSpecifies the device number of the trunk
whose D channel controls the B channels
of this trunk.rw INTEGER .1.3.6.1.4.1.2338.3.2.1.16 |
vdsx1TrunkNumberOfChannelsMaximum number of channels to be
initialized for this trunk -
0..24 for T1,
0..31 for E1,
0..8 for COPots.ro INTEGER .1.3.6.1.4.1.2338.3.2.1.17 |
vdsx1TrunkLineBuildOutDefines the line build out option. The following are applicable
values :
buildOut-minus15dB , i.e. -15 dB (1),
buildOut-0dB , i.e. 0 dB (2),
buildOut-minus7point5dB , i.e. -7.5 db (3) .rw INTEGER .1.3.6.1.4.1.2338.3.2.1.18 |
vdsx1TrunkLoopbackThis variable represents the loopback confi-
guration of the DS1 interface. Agents support-
ing read/write access should return badValue in
response to a requested loopback state that the
interface does not support. The values mean:
vdsx1NoLoop
Not in the loopback state. A device that
is not capable of performing a loopback on
the interface shall always return this as
it's value.
vdsx1PayloadLoop
The received signal at this interface is
looped through the device. Typically the
received signal is looped back for re-
transmission after it has passed through
the device's framing function.
vdsx1LineLoop
The received signal at this interface does
not go through the device (minimum pene-
tration) but is looped back out.
vdsx1OtherLoop
Loopbacks that are not defined here.rw Enumeration .1.3.6.1.4.1.2338.3.2.1.19 |
vdsx1TrunkRedLEDSpecifies the RED LED status of the trunk
OFF = 0,
ON = 1.ro INTEGER .1.3.6.1.4.1.2338.3.2.1.20 |
vdsx1TrunkYellowLEDSpecifies the YELLOW LED status of the trunk
OFF = 0,
ON = 1.ro INTEGER .1.3.6.1.4.1.2338.3.2.1.21 |
vdsx1TrunkChangePendingIndicates that a change to the device
values have been made to the registry.
The intepretation of the values are :
1 => change made to the registry, but
not incorporated in the device yet
0 => the device changes the value to 0
from 1, after it incorporates the
value from registry.ro INTEGER .1.3.6.1.4.1.2338.3.2.1.22 |
vdsx1ChannelTableChannel entries for each of the
channels associated with each trunk
defined in the trunk table. SEQUENCE OF VDsx1ChannelEntry .1.3.6.1.4.1.2338.3.9 |
vdsx1ChannelEntryEach entry is one channel in a T1/E1 trunk. VDsx1ChannelEntry .1.3.6.1.4.1.2338.3.9.1 |
vdsx1channelIndexThis is the logical channel number of the
channel within its trunk. For T1 it is between 1 and 24
for E1 it is between 1 and 32.ro INTEGER .1.3.6.1.4.1.2338.3.9.1.1 |
vdsx1channelTrunkIndexThis is the index of the trunk (relative to
its card) to which this channel belongs.ro INTEGER .1.3.6.1.4.1.2338.3.9.1.2 |
vdsx1channelSlotNumberThe value for this object is the
logical number of the slot in which the
card (and trunk) containing is located (vdsx1cardSlotNumber)..ro INTEGER .1.3.6.1.4.1.2338.3.9.1.3 |
vdsx1channelTrunkDeviceNumberThe value for this object is the logical device number of
the trunk containing this channel within its slot,
ie vdsx1TrunkDeviceNumberro INTEGER .1.3.6.1.4.1.2338.3.9.1.4 |
vdsx1channelEnabledSetting this variable to Deactivated will disable
this particular channel. Valid values are :
vdsx1channelDeactivated (100)
vdsx1channelActivated (1)
vdsx1channelNotConfigured (2)rw Enumeration .1.3.6.1.4.1.2338.3.9.1.5 |
vdsx1channelTypeChannel type,
vdsx1channelTypeUnknown : Unknown type
vdsx1channelTypeWink : E&M (Ear and Mouth) start
vdsx1channelTypeGS : Ground Start Digital trunk.
vdsx1channelTypeClear : Nailed up clear channel, for data
vdsx1channelTypeAnalogImm: Analog Trunk, Immediate start
vdsx1channelTypeBChan: PRI B channel on T1 or E1
vdsx1channelTypeDChan: PRI D channel on T1 or E1
vdsx1channelTypeAnalogDt: Analog channel, dialtone start
vdsx1channelTypeAnalogGs: Analog channel, ground start
vdsx1channelTypeDDS: DDS channel (56K or 64K)
vdsx1channelTypeAnalogDID: Analog channel, DID winkro Enumeration .1.3.6.1.4.1.2338.3.9.1.6 |
vdsx1channelStateThe Call State of this particular channel.
Valid values are :
Out of Service (channelStateOOS - 1),
Idle (channelStateIdle - 2),
InBound Call (channelStateInCall - 3),
OutBound Call (channelStateOutCall - 4),
Off line (channelStateOffline - 5),
Other state (channelStateOther - 6),
Data (channelStateData - 7),
Error (channelStateError - 8),
Ringing Far End (channelStateFeRinging - 9),
Incoming Ringing (channelStateNeRinging - 10),
Sending Digits (channelStateDigitSend - 11),
Receiving Digits (channelStateDigitRcv - 12),
Incall Established (channelStateIncallEst - 13),
Outcall Established (channelStateOutcallEst - 14),
Incall Clearing (channelStateIncallClear - 15),
Outcall Clearing (channelStateOutcallClear - 16).rw Enumeration .1.3.6.1.4.1.2338.3.9.1.7 |
vdsx1channelCallerIDThe callerID of an incoming caller, if available. If the callerID is
not available, then it will have a length of zerorw DisplayString .1.3.6.1.4.1.2338.3.9.1.8 |
vdsx1channelExternalAddressThe far end number of a connected call on this channel.If the number is
not available, then it will have a length of zero.rw DisplayString .1.3.6.1.4.1.2338.3.9.1.9 |
vdsx1channelExternalSubAddressThe far end sub address of a connected call on this channel.If this is
not available, then it will have a length of zerorw DisplayString .1.3.6.1.4.1.2338.3.9.1.10 |
vdsx1channelLocalAddressThe local number of a connected call on this channel.If the number is
not available, then it will have a length of zerorw DisplayString .1.3.6.1.4.1.2338.3.9.1.11 |
vdsx1channelLocalSubAddressThe local sub address of a connected call on this channel.If the number is
not available, then it will have a length of zerorw DisplayString .1.3.6.1.4.1.2338.3.9.1.12 |
vdsx1channelChangePendingIndicates that a change to the channel
values have been made to the registry.
The intepretation of the values are :
1 => change made to the registry, but
not incorporated in the device yet
0 => the device changes the value to 0
from 1, after it incorporates the
value from registry.ro INTEGER .1.3.6.1.4.1.2338.3.9.1.13 |