SYMBOL-DSSS-ENTERPRISE-PRIVATE-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for SYMBOL-DSSS-ENTERPRISE-PRIVATE-MIB.
315
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
315 total| Object Name |
|---|
coldStartAccess Point cold boot.
- apMyMacAddr is the MAC address of the Access Point
sending this trap message. TRAP-TYPE .1.3.6.1.4.1.343.6.3.0.0 |
authenticationFailureInvalid SNMP Community string.
- apMyMacAddr is the MAC address of the Access Point
sending this trap message.
- apAPMacAddr is the MAC address of the remote host
sending SNMP packet with invalid community. TRAP-TYPE .1.3.6.1.4.1.343.6.3.0.4 |
symbol OBJECT IDENTIFIER .1.3.6.1.4.1.388 |
RFC1155-SMI Unknown .1.3.6.1.4.1.388 |
spectrum24 OBJECT IDENTIFIER .1.3.6.1.4.1.388.1 |
dsap OBJECT IDENTIFIER .1.3.6.1.4.1.388.1.5 |
apDSAPRFStartUpTrapRF Driver is up.
- apMyMacAddr is the MAC address of the Access Point
sending this trap message. TRAP-TYPE .1.3.6.1.4.1.388.1.5.0.101 |
apDSAPACLViolationTrapMobile Unit MAC address not in the Access control
Table.
- apMyMacAddr is the MAC address of the Access Point
sending this trap message.
- muMacAddr is the MAC address of the Mobile Unit
not in the Access Control Table. TRAP-TYPE .1.3.6.1.4.1.388.1.5.0.102 |
apDSAPMUAssocTrapIndicates that there is one Mobile Unit associating
with this Access Point.
- apMyMacAddr is the MAC address of the Access Point
sending this trap message.
- muMacAddr is the MAC address of the Mobile Unit.
Note : If two or more Mobile Units associate with the
Access Point at the same time, muMacAddr
belongs to the last Mobile Unit.
- apCurrentMUs is the number of Mobile Units currently
associating with this Access Point. TRAP-TYPE .1.3.6.1.4.1.388.1.5.0.111 |
apDSAPMUUnAssocTrapIndicates that there is one Mobile Unit no longer
associating with this Access Point anymore.
- apMyMacAddr is the MAC address of the Access Point
sending this trap message.
- muMacAddr is the MAC address of the Mobile Unit.
Note : If two or more Mobile Units un-associate with
the Access Point at the same time, muMacAddr
belongs to the last Mobile Unit.
- apCurrentMUs is the number of Mobile Units currently
associating with this Access Point. TRAP-TYPE .1.3.6.1.4.1.388.1.5.0.112 |
apDSAPMUMaxAssocTrapIndicates that the number of MUs associated with this
Access Point is at the threshold set by apMaxMUTrigger.
- apMyMacAddr is the MAC address of the Access Point
sending this trap message.
- apCurrentMUs is the number of Mobile Units currently
associating with this Access Point. TRAP-TYPE .1.3.6.1.4.1.388.1.5.0.116 |
apDSRootWLAPUpTrapIndicates that the Root AP connection is setup and
is ready to forward data.
- apMyMacAddr is the MAC address of the Access Point
sending this trap message.
- apAPMacAddr is the MAC address of the Root AP.
- apNbrOfWLAPItfs is the number of current WLAP
Interfaces established. TRAP-TYPE .1.3.6.1.4.1.388.1.5.0.121 |
apDSRootWLAPLostTrapIf the current wireless AP does not receive Beacon
packet from its Root AP within one second, it will
consider the Root AP is lost. The wireless AP will
eventually reset itself to re-establish the network
topology.
- apMyMacAddr is the MAC address of the Access Point
sending this trap message.
- apAPMacAddr is the MAC address of the Root AP.
- apNbrOfWLAPItfs is the number of current WLAP
Interfaces established. TRAP-TYPE .1.3.6.1.4.1.388.1.5.0.122 |
apDSDsgntedWLAPUpTrapIndicates that the Designated WLAP connection is setup
and is ready to forward data.
- apMyMacAddr is the MAC address of the Access Point
sending this trap message.
- apAPMacAddr is the MAC address of the Designated
WLAP.
- apNbrOfWLAPItfs is the number of current WLAP
Interfaces established. TRAP-TYPE .1.3.6.1.4.1.388.1.5.0.123 |
apDSDsgnatedWLAPLostTrapIf the current wireless AP does not receive Config BPDU
(Bridge Protocol Data Unit) packet from its Designated
WLAP for MAX AGE time, it will consider that the
Designated WLAP is lost.
- apMyMacAddr is the MAC address of the Access Point
sending this trap message.
- apAPMacAddr is the MAC address of the Designated
WLAP.
- apNbrOfWLAPItfs is the number of current WLAP
Interfaces established. TRAP-TYPE .1.3.6.1.4.1.388.1.5.0.124 |
apDSAPDHCPConfigChgTrapIf there are any DHCP network configuration
change, This trap will be issued.
- apMyMacAddr is the MAC address of the Access Point
sending this trap message. TRAP-TYPE .1.3.6.1.4.1.388.1.5.0.130 |
apDSAPDHCPLeaseUpTrapIf the Access point(Client) is unable to renew the DHCP
lease before the lease is expired, this trap is generated.
- apMyMacAddr is the MAC address of the Access Point
sending this trap message. TRAP-TYPE .1.3.6.1.4.1.388.1.5.0.131 |
apConfigMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.388.1.5.1 |
apManufactureInfo OBJECT IDENTIFIER .1.3.6.1.4.1.388.1.5.1.1 |
apModelnumberThe Model Number of the Access Point device.ro DisplayString .1.3.6.1.4.1.388.1.5.1.1.1 |
apSerialnumberThe Serial Number of the Access Point system.ro DisplayString .1.3.6.1.4.1.388.1.5.1.1.2 |
apHardwareRevThe current revision of the Access Point hardware.ro DisplayString .1.3.6.1.4.1.388.1.5.1.1.3 |
apMyMacAddrThe MAC address of the Access Point.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.388.1.5.1.1.4 |
apAPFirmwareRevThe current revision of the Access Point firmware.ro DisplayString .1.3.6.1.4.1.388.1.5.1.1.5 |
apRFFirmwareRevThe current revision of the Access Point radio
firmware.ro DisplayString .1.3.6.1.4.1.388.1.5.1.1.6 |
apMfgDateThe Date this Access Point was manufactured.ro DisplayString .1.3.6.1.4.1.388.1.5.1.1.7 |
apHTMLFileRevThe current revision of the Access Point HTML file.ro DisplayString .1.3.6.1.4.1.388.1.5.1.1.8 |
apVendorIDDisplays the Vendor ID of the vendor for which this AP
has been manufactured for. The current values are:
- Symbol (5)
- 3Com (6)
- Ericsson (8)
- Intel (9)ro Enumeration .1.3.6.1.4.1.388.1.5.1.1.9 |
apSystemConfig OBJECT IDENTIFIER .1.3.6.1.4.1.388.1.5.1.2 |
apUnitNameAn ASCII string to identify this Access Point (up to
31 characters).rw DisplayString .1.3.6.1.4.1.388.1.5.1.2.1 |
apMyIPAddrThe IP address for the AP.rw IpAddress .1.3.6.1.4.1.388.1.5.1.2.2 |
apSubnetMaskThe IP subnet mask for the AP.rw IpAddress .1.3.6.1.4.1.388.1.5.1.2.3 |
apGatewayIPAddrThe IP address for the default gateway.rw IpAddress .1.3.6.1.4.1.388.1.5.1.2.4 |
apDefaultInterfaceSpecifies the default interface (Ethernet, PPP
or WLAP) for the AP to forward an unknown packet.
Default is ethernet(1).rw Enumeration .1.3.6.1.4.1.388.1.5.1.2.5 |
apEnetPortStateSpecifies the state of the Ethernet interface.
Default is up(1).rw Enumeration .1.3.6.1.4.1.388.1.5.1.2.6 |
apEthernetTimeOutIf the value is:
- 0: the Ethernet Time Out function is disabled.
- 1: detect Ethernet timeout by hardware circuitry.
- 30-255: Ethernet timeout is detected by software
algorithm.
When the Ethernet connection is broken and the WLAP
mode is either enabled or disabled, the AP will clear
the MU table and disable the RF interface until the
Etherent connection is up.
The following values are only valid when WLAP mode is
enabled and it does not matter whetehr WLAP associates
with the root AP or not.
- 2: send WLAP Alive BPDU on Ethernet interface to let
other WLAP on the same Ethernet segment to detect
it's existence.
- 3: keep track of WLAP Alive BPDU on Ethernet inter-
face. If the BPDU is missing for 'WLAP Hello Time'
seconds, the Ethernet Activity LEDs will flash and
the RF interface is disabled until the WLAP Alive
BPDU is received again, then the AP will reset itself.
The default value is 0.rw INTEGER .1.3.6.1.4.1.388.1.5.1.2.7 |
apTelnetEnableEnables/Disables Telnet access to the AP. Default is
enabled(1).rw Enumeration .1.3.6.1.4.1.388.1.5.1.2.8 |
apAccCtrlEnableEnables/Disables the Access Control function.
When it is enabled, a Mobile Unit can associate with
the Access Point only if its MAC address is in the
Access Control Table. Default is disabled(2).rw Enumeration .1.3.6.1.4.1.388.1.5.1.2.9 |
apTypeFilterEnableSpecifies the type of Access Point Type Filtering
operation, i.e. Disabled/Forward/Discard. Default is
disabled(1).rw Enumeration .1.3.6.1.4.1.388.1.5.1.2.10 |
apWNMPEnableEnables/Disables Use of the WNMP agent. Default is
enabled(1).rw Enumeration .1.3.6.1.4.1.388.1.5.1.2.13 |
apAPStateXchgEnableEnables/Disables exchanging Access Point to Access
Point state information by using WNMP protocol. Default
is enabled(1).rw Enumeration .1.3.6.1.4.1.388.1.5.1.2.14 |
apS24MobileIPEnableEnables/Disables Spectrum24 Mobile IP support, i.e. AP
will act as Mobility Agent. Default is disabled(2).rw Enumeration .1.3.6.1.4.1.388.1.5.1.2.15 |
apAgentAdIntervalInterval in second at which Mobility Agent Advertise-
ments are sent by the Third Party Mobility Agent(s).
AP will cache the Third Party Advertisement and pass
it to MU at association time. If AP does not receive
the Advertisement within the interval seconds, the
cached Advertisement will be deleted. If the interval
is 0 or apS24MobileIPEnable is enabled, caching of
the Advertisement will not occur. Range (0..1200) 3*Seconds .
Default is 0.rw INTEGER .1.3.6.1.4.1.388.1.5.1.2.16 |
apWebServerEnableEnables/Disables Access Point Web Server. When
enabled, the Access Point will serve Web clients.
Default is enabled(1)rw Enumeration .1.3.6.1.4.1.388.1.5.1.2.17 |
apMobileHomeMD5KeyThe MD5 key is a secret key shared between home agent
and the mobile unit. This is used to generate a MD5
checksum, which is used for packet authentication.
Length of this variable should not exceed 13 characters.rw DisplayString .1.3.6.1.4.1.388.1.5.1.2.18 |
apAdditionalGatewaysTableA table of information for additional Gateways.
The current number of entries is 7. SEQUENCE OF ApAdditionalGatewaysEntry .1.3.6.1.4.1.388.1.5.1.2.19 |
apAdditionalGatewaysEntryAn entry in the table of information for additional
gateways for this access point.
A row in this table cannot be created or deleted by
SNMP operations on columns of the table. ApAdditionalGatewaysEntry .1.3.6.1.4.1.388.1.5.1.2.19.1 |
additionalGatewaysIndexSpecific Gateway information Table index. Range (1..8).ro INTEGER .1.3.6.1.4.1.388.1.5.1.2.19.1.1 |
apAdditionalGatewaysIPAddrThe IP address of the Gateway used for this AP.rw IpAddress .1.3.6.1.4.1.388.1.5.1.2.19.1.2 |
apMUMUDisallowedControls inter-MU communication. When enabled(on),
it will disallow one MU to talk to another MU
through RF only.rw Enumeration .1.3.6.1.4.1.388.1.5.1.2.20 |
apEncryptAdminControls the administration of Encryption keys.
This variable could only be modified thru the
Serial Interface. Default is any(2).ro Enumeration .1.3.6.1.4.1.388.1.5.1.2.21 |
apSNMPInfo OBJECT IDENTIFIER .1.3.6.1.4.1.388.1.5.1.3 |
apSNMPModeSpecifies the mode of the SNMP Agent operation, i.e.
Disabled/Readonly/ReadWrite. Default is readwrite(3).rw Enumeration .1.3.6.1.4.1.388.1.5.1.3.1 |
apROCommunityNameThe Read-Only community name of the SNMP command for
management station accessing this Access Point (up to
31 characters).rw DisplayString .1.3.6.1.4.1.388.1.5.1.3.2 |
apRWCommunityNameThe Read-Write community name of the SNMP command for
management station accessing this Access Point (up to
13 characters). This community name is same as the
System Password or Telnet Password. For security
purpose, if the management station uses the READ-ONLY
community name to access this object, a string of
'xxxxx' will be returned.rw DisplayString .1.3.6.1.4.1.388.1.5.1.3.3 |
apTrapHost1IpAdrTrap receiver's (i.e. Network Manager's) IP address.rw IpAddress .1.3.6.1.4.1.388.1.5.1.3.4 |
apAllTrapsEnableEnables/Disables all SNMP traps. Default is disabled
(2).rw Enumeration .1.3.6.1.4.1.388.1.5.1.3.5 |
apColdBootTrapEnableEnables/Disables Access Point Cold Boot trap. Default
is disabled(1). This is a generic-trap and the trap
code is 0.
When not disabled the trap could be directed to TrapHost1,
TrapHost2 or all TrapHosts.
The apAllTrapsEnable flag should be enabled for this trap
to be issued.rw Enumeration .1.3.6.1.4.1.388.1.5.1.3.6 |
apAuthenFailureTrapEnableEnables/Disables authentication failure trap. Default
is disabled(2). This is a generic-trap and the trap
code is 4.
When not disabled the trap could be directed to TrapHost1,
TrapHost2 or all TrapHosts.
The apAllTrapsEnable flag should be enabled for this trap
to be issued.rw Enumeration .1.3.6.1.4.1.388.1.5.1.3.7 |
apRFTrapEnableEnables/Disables Access Point RF driver startup trap.
Default is disabled(2). This is an enterprise-specific
trap and the trap code is 101.
When not disabled the trap could be directed to TrapHost1,
TrapHost2 or all TrapHosts.
The apAllTrapsEnable flag should be enabled for this trap
to be issued.rw Enumeration .1.3.6.1.4.1.388.1.5.1.3.8 |
apACLTrapEnableEnables/Disables Access Control violation trap. Default
is disabled(2). This is an enterprise-specific trap
and the trap code is 102.
When not disabled the trap could be directed to TrapHost1,
TrapHost2 or all TrapHosts.
The apAllTrapsEnable flag should be enabled for this trap
to be issued.rw Enumeration .1.3.6.1.4.1.388.1.5.1.3.9 |
apMUStateChngTrapEnableEnables/Disables Mobile Unit State Change trap.
Default is disabled(1). When not disabled, the
following four (2) enterprise-specific traps will
be generated and directed to trapHost1,
TrapHost2 or all traphosts.:
- MU Association Trap, the trap code is 111.
- MU Un-association Trap, the trap code is 112.
The enabled/disabled state of this trap depends on the
state of apAllTrapsEnable.rw Enumeration .1.3.6.1.4.1.388.1.5.1.3.10 |
apWLAPConnChngTrapEnableWhen Enabled, if there are any WLAP Connection Change,
one of four (4) following enterprise-specific traps
will be issued.
- Root AP Up Trap, the trap code is 121.
- Root AP Lost Trap, the trap code is 122.
- Designated WLAP Up Trap, the trap code is 123.
- Designated WLAP Lost Trap, the trap code is 124.
Default is disabled(2).
When not disabled the trap could be directed to TrapHost1,
TrapHost2 or all TrapHosts.
The apAllTrapsEnable flag should be enabled for this trap
to be issued.rw Enumeration .1.3.6.1.4.1.388.1.5.1.3.11 |
apDHCPChangeEnableWhen Enabled, if there are any DHCP network configuration
change, a trap will be issued. Default is disabled(2).
When not disabled the trap could be directed to TrapHost1,
TrapHost2 or all TrapHosts.
The apAllTrapsEnable flag should be enabled for this trap
to be issued.rw Enumeration .1.3.6.1.4.1.388.1.5.1.3.12 |
apSNMPRequestsIndicates the number of SNMP requests to
this SNMP Agent.ro Counter .1.3.6.1.4.1.388.1.5.1.3.13 |
apSNMPTrapsIndicates the number of Traps that were generated
by this SNMP Agent.ro Counter .1.3.6.1.4.1.388.1.5.1.3.14 |
apTrapHost2IpAdrTrap receiver's (i.e. Network Manager's) IP address.rw IpAddress .1.3.6.1.4.1.388.1.5.1.3.15 |
apRFConfig OBJECT IDENTIFIER .1.3.6.1.4.1.388.1.5.1.4 |
apRFPortStateSpecifies the state of the RF Interface. Default is
up(1).rw Enumeration .1.3.6.1.4.1.388.1.5.1.4.1 |
apNetIDThe current RF Network ID for the AP. The Network
name can have up to 32 alphanumerical characters.rw DisplayString .1.3.6.1.4.1.388.1.5.1.4.2 |
apCountryNameThe country for which the Access Point radio is
configured. It is set at the factory and may not be
altered.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.388.1.5.1.4.5 |
apAntennaSelectSelect either Primary antenna only (i.e. Disable
antenna diversity) or both Primary and Secondary
antennas (i.e. Enable antenna diversity-On). Default is
diversity-On(2).rw Enumeration .1.3.6.1.4.1.388.1.5.1.4.6 |
apBCMCQMaxThe maximum size of broadcast/multicast queue.
Range (0..32). Default is 10.rw INTEGER .1.3.6.1.4.1.388.1.5.1.4.8 |
apReassemblyTimeOutSets the time in 0.5 ms units before a timeout occurs
during a packet re-assembly. Packet re-assemblies
occur when a large Ethernet packet is fragmented into
smaller wireless network packets.
Range : 0...9999. Default is 9000.rw INTEGER .1.3.6.1.4.1.388.1.5.1.4.9 |
apMaxRetriesThe maximum number of allowed retries before aborting
a single transmission. Range (0..32). Default is 15.rw INTEGER .1.3.6.1.4.1.388.1.5.1.4.10 |
apMulticastMaskSupports broadcast download protocol for Point-of-Sale
terminals that load a new operating image over the
network instead of using a local non-volatile drive.
The multicast mask is the top 32 bits of the MAC
address and allows for a series of MAC addresses to
receive multicast messages. These messages are
transmitted by the AP immediately and not queued for
processing at DTIM intervals.rw OCTET STRING .1.3.6.1.4.1.388.1.5.1.4.11 |
apAcceptBCESSIDEnables/Disables the function to accept Broadcast ESS
ID. Enabling this feature is NOT recommended. See
manual for details. Default is disabled(2).rw Enumeration .1.3.6.1.4.1.388.1.5.1.4.14 |
apMUInactivityTimeOutAllowable Mobile Unit inactivity time in minutes. The
time out limit is from 3 to 600 minutes. Default is
60 minutes.rw INTEGER .1.3.6.1.4.1.388.1.5.1.4.15 |
apWLAPModeEnables/Disables Wireless AP capability and set link
required option to wireless AP.
Once in link-required mode, upon power-up, Root AP
requires connection to the Ethernet cable and WLAP
requires association with the Root AP and WLAP will
keep probing forever.
Default is disabled(2).rw Enumeration .1.3.6.1.4.1.388.1.5.1.4.16 |
apWLAPPriorityProvides a user with the influence to determine the
Root AP in wireless operation. The priority value is
added as the most significant portion of the MAC
address to form the WLAP ID. A WLAP with a lower
numerical value for priority is more likely to become
the Root AP.
Priority 0xFFFF is special. It grants the WLAP with
roaming capability.
Default is 8000 hex from the 0 - 0xFFFF
range. Reset AP for value to take effect.rw OCTET STRING .1.3.6.1.4.1.388.1.5.1.4.17 |
apWLAPManualBSSIDSpecifies the BSS-ID of a particular WLAP and forces
the current WLAP to associate only with that WLAP.
When WLAP Manaul BSS ID is set to the current WLAP MAC
address, the current WLAP jumps into Functional state
immediately and waits for an Association Request from
the other WLAP. Reset AP for value to take effect.rw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.388.1.5.1.4.18 |
apWLAPHelloTimeSets the time lapse, in seconds, between Configuration
BPDUs (Bridge Protocol Data Unit) sent to the Root AP
by a designated WLAP to indicate that it is still
alive. Default is 20 seconds. Reset AP for value
to take effect. Range: 0..9999.rw INTEGER .1.3.6.1.4.1.388.1.5.1.4.19 |
apWLAPMaxAgeSpecifies how long, in seconds, a Configuration BPDU
(Bridge Protocol Data Unit) is kept by the Root AP
before it is judged too old and discarded.
Consequently, the interface is considered to be
disconnected. Default is 100 seconds. Recommended
value is multiple of the WLAP Hello Time. Reset AP for
value to take effect. Range: 0..9999.rw INTEGER .1.3.6.1.4.1.388.1.5.1.4.20 |
apWLAPFwdDelaySpecifies how long, in seconds, an WLAP is prevented
from forwarding data packets to an interface.
This delay is to allow the spread of news of a topology
change to all parts of a network. Default is 5 seconds.
Reset AP for value to take effect. Range: 0..9999.rw INTEGER .1.3.6.1.4.1.388.1.5.1.4.21 |
apMaxMUTriggerIndicates the trigger point for sending
apMUMaxAssocTrap trap. Range (1..255).
The default value is 255.rw INTEGER .1.3.6.1.4.1.388.1.5.1.4.24 |
apMaxRetriesVoiceThe maximum number of allowed retries before aborting
a single transmission. Range (0..32). Default is 5.rw INTEGER .1.3.6.1.4.1.388.1.5.1.4.25 |
apMcastMaskVoiceThis is used for Spectrum 24 telephone for intercomm
function.
The multicast mask is the top 32 bits of the MAC
address and allows for a series of MAC addresses to
receive multicast messages. These messages are
transmitted by the AP immediately and not queued for
processing at DTIM intervals..rw OCTET STRING .1.3.6.1.4.1.388.1.5.1.4.26 |
apWEPAlgorithmThis attribute is a set of all the shared key WEP algorithms
supported by the STAs. The following are the default values
and the associated algorithm.
Value = 1: 128 bit Key
Value = 2: 40 bit Key.
IMPORTANT NOTE: The 128 bit WEP key ENcryption is currently
restricted by U.S. laws. In order to activate the 128 bit
Encryption, an authentic License key has to be obtained and
entered through one of the interfaces such as Telnet, SNMP
or Web. Upon authentication of the key the AP will enable
the 128 bit ENcryption. See Access Point manual for details.rw Enumeration .1.3.6.1.4.1.388.1.5.1.4.30 |
apRFRate11MbSpecifies the Current state of the RF data rate. There
are three options:
- optional(1)
- not-used(2)
- required(3)
Default is optional for 11 Mb/s data rate.rw Enumeration .1.3.6.1.4.1.388.1.5.1.4.31 |
apRFRate5-5MbSpecifies the Current state of the RF data rate. There
are three options:
- optional(1)
- not-used(2)
- required(3)
Default is optional for 5.5 Mb/S data rate.rw Enumeration .1.3.6.1.4.1.388.1.5.1.4.32 |
apRFRate2MbSpecifies the Current state of the RF data rate. There
are three options:
- optional(1)
- not-used(2)
- required(3)
Default is optional for 2 Mb/s data rate.rw Enumeration .1.3.6.1.4.1.388.1.5.1.4.33 |
apRFRate1MbSpecifies the Current state of the RF data rate. There
are three options:
- optional(1)
- not-used(2)
- required(3)
Default is required for 1 Mb/s data rate.rw Enumeration .1.3.6.1.4.1.388.1.5.1.4.34 |
apRFPreambleThis attribute is set to disabled for compatibility
within the 802.11 community. Setting it to enabled shall
result in performance enhancement. Default is enabled.
NOTE: Only radios with version 2 hardware support RF
Preamble, hence configurable to enabled state.rw Enumeration .1.3.6.1.4.1.388.1.5.1.4.35 |
apRadioTypeThis attribute displays the type of radio installed in
the Access Point.
ds11-v1 Ver.1 Hardware short RF Preamble not supported.
ds11-V2 Ver.2 Hardware Short RF Preamble supported.ro Enumeration .1.3.6.1.4.1.388.1.5.1.4.36 |
apSerialPortConfig OBJECT IDENTIFIER .1.3.6.1.4.1.388.1.5.1.5 |
apPPPStateIndicates the current state of the PPP connection
machine. Default is down(2).rw Enumeration .1.3.6.1.4.1.388.1.5.1.5.1 |
apSerialPortUseSpecifies whether the Serial Interface is to be used
as User Interface(UI) or PPP. Default is ui(2).rw Enumeration .1.3.6.1.4.1.388.1.5.1.5.2 |
apModemConnectedSpecifies whether the Serial Interface has a modem
attached to it. Default is no(2).rw Enumeration .1.3.6.1.4.1.388.1.5.1.5.3 |
apConnectModeSpecifies the Modem connection mode:
- originate(1): AP sends dial-out information.
- answer(2): AP waits for dial-in information.
Default is answer(2).rw Enumeration .1.3.6.1.4.1.388.1.5.1.5.4 |
apDialOutNumberSpecifies the number to be dialed by the modem.rw DisplayString .1.3.6.1.4.1.388.1.5.1.5.5 |
apDialOutModeSpecifies the dialout mode:
- auto(1): Modem dial out during startup time.
- manual(2): Modem dial out by manned intervention
Default is auto(1).rw Enumeration .1.3.6.1.4.1.388.1.5.1.5.6 |
apAnswerWaitTimeSpecifies the period (in seconds) the AP will wait for
the remote unit to answer the call. Default is 60
seconds.rw INTEGER .1.3.6.1.4.1.388.1.5.1.5.7 |
apModemSpeakerSpecifies if modem speaker is turned on(1) or off(2).
Default is on(1).rw Enumeration .1.3.6.1.4.1.388.1.5.1.5.8 |
apInactivityTimeoutSpecifies the User Interface inactivity timeout in
minutes. 0 means no timeout. Default is 5 minutes.rw INTEGER .1.3.6.1.4.1.388.1.5.1.5.9 |
apPPPTimeoutSpecifies the PPP event timeout in seconds. Default is
3 seconds.rw INTEGER .1.3.6.1.4.1.388.1.5.1.5.10 |
apPPPTerminatesSpecifies the maximum number of PPP terminate requests.
Default is 10.rw Counter .1.3.6.1.4.1.388.1.5.1.5.11 |
apAddrFilterTableA table of MAC addresses not allowed to associate with
the Access Point.
The maximum number of entries in the table is 512. SEQUENCE OF ApAddrFilterEntry .1.3.6.1.4.1.388.1.5.1.6 |
apAddrFilterEntryAn entry in the table of Address Filter.
A row in this table is created by setting the value of
disallowedMU to the MAC address of the MU not allowed
to associate with the Access Point.
A row in this table is deleted by setting the value of
disallowedMU to '000000000000'. ApAddrFilterEntry .1.3.6.1.4.1.388.1.5.1.6.1 |
disallowedIndexAddress Filter Table index. Range (1..512).ro INTEGER .1.3.6.1.4.1.388.1.5.1.6.1.1 |
disallowedMUMU MAC address which is not allowed to be associated
with this Access Point.rw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.388.1.5.1.6.1.2 |
apTypeFilterTableA table of Ethernet types (i.e. 16-bit DIX Ethernet
type), which are entered by the user and supported for
the type filtering function.
The maximum number of entries in the table is 16. SEQUENCE OF ApTypeFilterEntry .1.3.6.1.4.1.388.1.5.1.7 |
apTypeFilterEntryAn entry in the table of Type Filter.
A row in this table is created by setting the value of
etherType to Ethernet packet type in hexadecimal.
A row in this table is deleted by setting the value of
etherType to 00 ApTypeFilterEntry .1.3.6.1.4.1.388.1.5.1.7.1 |
typeIndexFilter Type Table index. Range (1..16).ro INTEGER .1.3.6.1.4.1.388.1.5.1.7.1.1 |
etherTypeA 16-bit Ethernet Protocol Type in hexadecimal.
Range of valid Entries: 0X05DD .. 0XFFFErw OCTET STRING .1.3.6.1.4.1.388.1.5.1.7.1.2 |
ap128bWEPKeyTableA table of default WEP Keys
The maximum number of entries in the table is 4. SEQUENCE OF ApWEPKeyEntry .1.3.6.1.4.1.388.1.5.1.8 |
apWEPKeyEntryAn entry in the table of Default WEP Keys. ApWEPKeyEntry .1.3.6.1.4.1.388.1.5.1.8.1 |
ap128bWepkeyIndexWEP Key Table index. Range (1..4).ro INTEGER .1.3.6.1.4.1.388.1.5.1.8.1.1 |
ap128bWepKeyValueA Default WEP Key Value. This value should be
26 character long.
IMPORTANT NOTE: The 128 bit WEP key Encryption is currently
restricted by U.S. laws. Its use is restricted to AP's
manufactured for U.S. only. In order to activate the 128 bit
Encryption for all other countries, an access code has to be
obtained and entered through one of the interfaces such as
Serial, Telnet, SNMP or Web. Upon authentication of the key
the AP will enable the 128 bit Encryption.
See Access Point manual for details.rw WEPKeytype128b .1.3.6.1.4.1.388.1.5.1.8.1.2 |
apPerformMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.388.1.5.2 |
apTrafficMatrixTableA table of Access Point Traffic Matrix which provides
information on packets transmitted from one interface
to another (Ethernet, PPP, radio, AP). The table also
displays the number of broadcast packets transmitted
from the Access Point.
The current number of entries is 5. SEQUENCE OF ApTrafficMatrixEntry .1.3.6.1.4.1.388.1.5.2.1 |
apTrafficMatrixEntryAn entry in the table of Access Point Traffic Matrix.
A row in this table cannot be created or deleted by
SNMP operations on columns of the table. ApTrafficMatrixEntry .1.3.6.1.4.1.388.1.5.2.1.1 |
apTMTableIndexAccess Point Traffic Matrix Table index. Range (1..5).ro INTEGER .1.3.6.1.4.1.388.1.5.2.1.1.1 |
apProtoItfNameAccess Point Protocol Interface Name (i.e. Ethernet, PPP,
Radio, AP).ro DisplayString .1.3.6.1.4.1.388.1.5.2.1.1.2 |
apNPktsToEnetsIndicates the number of packets sent from the Access
Point Protocol Interface to the Ethernet Interface.
This field should always be zero if the Access Point
Protocol Interface is Ethernet.ro Counter .1.3.6.1.4.1.388.1.5.2.1.1.3 |
apNPktsToPppsIndicates the number of packets sent from the Access
Point Protocol Interface to the PPP Interface.
This field is meaningful only if the PPP interface is
enabled.ro Counter .1.3.6.1.4.1.388.1.5.2.1.1.4 |
apNPktsToRfsIndicates the number of packets sent from the Access
Point Protocol Interface to the RF Interface. If the
Access Point Protocol Interface is RF, these are
frames from one MU to another.ro Counter .1.3.6.1.4.1.388.1.5.2.1.1.5 |
apNPktsToAPStksIndicates the number of packets sent from the Access
Point Protocol Interface to the internal Access Point
stack. This field should always be zero if the Access
Point Protocol Interface is Access Point Stack.ro Counter .1.3.6.1.4.1.388.1.5.2.1.1.6 |
apItfStatTableA table of Access Point Interfaces Statistics, which
provides packets forwarding statistics for each inter-
face (Ethernet, PPP, RF, AP stack).
Interface statistics also provide performance informa-
tion for each interface in Packets-per-second (PPS) and
Bytes- per-second (BPS).
The AP interface indicates packets sent to the AP stack
(e.g. configuration requests, SNMP, Telnet etc.).
The current number of entries is 4. SEQUENCE OF ApItfStatEntry .1.3.6.1.4.1.388.1.5.2.2 |
apItfStatEntryAn entry in the table of Access Point Interface
Statistics.
A row in this table cannot be created or deleted by
SNMP operations on columns of the table. ApItfStatEntry .1.3.6.1.4.1.388.1.5.2.2.1 |
apItfStatIndexAccess Point Interface Statistics Table index.
Range (1..4).ro INTEGER .1.3.6.1.4.1.388.1.5.2.2.1.1 |
apInterfaceNameAccess Point Interface Name (Ethernet, PPP, RF,
AP).ro DisplayString .1.3.6.1.4.1.388.1.5.2.2.1.2 |
apPacketsInsIndicates the number of good packets received on the
specified interface.ro Counter .1.3.6.1.4.1.388.1.5.2.2.1.3 |
apPacketsOutsIndicates the number of packets successfully
transmitted on the specified interface.ro Counter .1.3.6.1.4.1.388.1.5.2.2.1.4 |
apOctetsInsIndicates the number of good bytes received on the
specified interface.ro Counter .1.3.6.1.4.1.388.1.5.2.2.1.5 |
apOctetsOutsIndicates the number of bytes successfully transmitted
on the specified interface.ro Counter .1.3.6.1.4.1.388.1.5.2.2.1.6 |
apPktsInPerSecIndicates the number of good packets per second
received on the specified Interface.ro Gauge .1.3.6.1.4.1.388.1.5.2.2.1.7 |
apPktsOutPerSecIndicates the number of packets per second successfully
transmitted on the specified interface.ro Gauge .1.3.6.1.4.1.388.1.5.2.2.1.8 |
apOctInPerSecIndicates the number of good bytes per second
received on the specified Interface.ro Gauge .1.3.6.1.4.1.388.1.5.2.2.1.9 |
apOctOutPerSecIndicates the number of bytes per second successfully
transmitted on the specified interface.ro Gauge .1.3.6.1.4.1.388.1.5.2.2.1.10 |
apEthernetStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.388.1.5.2.3 |
apEPktsSeensIndicates the number of packets that have been seen on
the Ethernet interface. Most of these packets are for
stations other than those associated with this AP.ro Counter .1.3.6.1.4.1.388.1.5.2.3.1 |
apEPktsForwardedsIndicates the number of Ethernet packets forwarded
from the Ethernet interface to other interfaces.ro Counter .1.3.6.1.4.1.388.1.5.2.3.2 |
apEPktsDiscNoMatchsIndicates the number of packets discarded due to
unknown destination (i.e. no database entry).ro Counter .1.3.6.1.4.1.388.1.5.2.3.3 |
apEPktsDiscForcedsIndicates the number of packets discarded due to Type
or Address filters applied.ro Counter .1.3.6.1.4.1.388.1.5.2.3.4 |
apEPktsDiscBuffersIndicates the number of packets discarded due to lack
of available buffers in AP.ro Counter .1.3.6.1.4.1.388.1.5.2.3.5 |
apEPktsDiscCRCsIndicates the number of packets discarded due to CRC
errors.ro Counter .1.3.6.1.4.1.388.1.5.2.3.6 |
apEPktsSentsIndicates the number of packets sent by this Ethernet
Port.ro Counter .1.3.6.1.4.1.388.1.5.2.3.7 |
apEAnyCollisionsIndicates the number of packets that suffer at least
one collision.ro Counter .1.3.6.1.4.1.388.1.5.2.3.8 |
apE1orMoreCollsIndicates the number of packets that suffer more than
one collision.ro Counter .1.3.6.1.4.1.388.1.5.2.3.9 |
apEMaxCollisionsIndicates the number of packets that suffer more than
the maximum number of collisions.ro Counter .1.3.6.1.4.1.388.1.5.2.3.10 |
apELateCollisionsIndicates the number of packets that suffer late
collisions.ro Counter .1.3.6.1.4.1.388.1.5.2.3.11 |
apEPktsDefersIndicates the times AP had to defer transmit requests
on Ethernet due to busy medium.ro Counter .1.3.6.1.4.1.388.1.5.2.3.12 |
apEBcMcPktsIndicates the number of broadcast/multicast packets
that have been transmitted.ro Counter .1.3.6.1.4.1.388.1.5.2.3.13 |
apEIndividualAddrsIndicates the number of individual address (unicast)
packets that have been received.ro Counter .1.3.6.1.4.1.388.1.5.2.3.14 |
apRFStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.388.1.5.2.4 |
rfBcMcPktsSentsIndicates the number of broadcast/multicast packets
that have been successfully transmitted.ro Counter .1.3.6.1.4.1.388.1.5.2.4.1 |
rfBcMcPktsRcvdsIndicates the number of broadcast/multicast packets
that have been successfully received.ro Counter .1.3.6.1.4.1.388.1.5.2.4.2 |
rfBcMcOctSentsIndicates the number of broadcast/multicast bytes that
have been successfully transmitted.ro Counter .1.3.6.1.4.1.388.1.5.2.4.3 |
rfBcMcOctRcvdsIndicates the number of broadcast/multicast bytes that
have been successfully received.ro Counter .1.3.6.1.4.1.388.1.5.2.4.4 |
rfSysPktsSentsIndicates the number of system packets (includes probe
operations packets) that have been successfully
transmitted.ro Counter .1.3.6.1.4.1.388.1.5.2.4.5 |
rfSysPktsRcvdsIndicates the number of system packets (includes probes
/associate packets) that have been successfully
received.ro Counter .1.3.6.1.4.1.388.1.5.2.4.6 |
rfSBcMcPktsSentsIndicates the number of system broadcast/multicast
packets (includes beacons) that have been successfully
transmitted.ro Counter .1.3.6.1.4.1.388.1.5.2.4.7 |
rfSBcMcPktsRcvdsIndicates the number of system broadcast/multicast
(includes beacons) packets that have been successfully
received.ro Counter .1.3.6.1.4.1.388.1.5.2.4.8 |
rfSuccFragPktsIndicates the number of packets that were fragmented
and for which all fragments were acked.ro Counter .1.3.6.1.4.1.388.1.5.2.4.9 |
rfUnsuccFragPktsIndicates the number of packets that were fragmented
but for which one or more fragments were not acked.ro Counter .1.3.6.1.4.1.388.1.5.2.4.10 |
rfTotalFragSentsIndicates the number of packets fragments that have
been sent.ro Counter .1.3.6.1.4.1.388.1.5.2.4.11 |
rfTotalFragRcvdsIndicates the number of packets fragments that have
been received.ro Counter .1.3.6.1.4.1.388.1.5.2.4.12 |
rfSuccReassPktsIndicates the number of packets that were reassigned
and successfully reassembled.ro Counter .1.3.6.1.4.1.388.1.5.2.4.13 |
rfUnsuccReassPktsIndicates the number of packets that were
unsuccessfully reassembled.ro Counter .1.3.6.1.4.1.388.1.5.2.4.14 |
rfAssocMUsIndicates the number of MUs currently associated with
this AP.ro Counter .1.3.6.1.4.1.388.1.5.2.4.15 |
rfRcvdCRCErrorsIndicates the number of packets that were received but
had the CRC errors.ro Counter .1.3.6.1.4.1.388.1.5.2.4.16 |
rfRcvdDupPktsIndicates the number of packets that were received but
were duplicates of previously received. This is usually
an indication that an ACK was not received by the
sending unit.ro Counter .1.3.6.1.4.1.388.1.5.2.4.17 |
rfTotalCollisionsIndicates the number of collisions that have occured on
the interface. A collision on the RF interface means
that an ack was not received or that a RTS was not
answered by a CTS.ro Counter .1.3.6.1.4.1.388.1.5.2.4.18 |
rfPktsWithoutCollsIndicates the number of packets without any collision.ro Counter .1.3.6.1.4.1.388.1.5.2.4.19 |
rfPktsWithMaxCollsIndicates the number of packets that suffered the
maximum number of collisions.ro Counter .1.3.6.1.4.1.388.1.5.2.4.20 |
rfPktsWithCollsIndicates the number of packets that suffered at least
one collision.ro Counter .1.3.6.1.4.1.388.1.5.2.4.21 |
rfDataPktsSentsIndicates the number of packets transmitted.ro Counter .1.3.6.1.4.1.388.1.5.2.4.22 |
rfDataPktsRcvdsIndicates the number of packets that were successfully
received.ro Counter .1.3.6.1.4.1.388.1.5.2.4.23 |
rfDataOctetsSentsIndicates the number of octets transmitted.ro Counter .1.3.6.1.4.1.388.1.5.2.4.24 |
rfDataOctetsRcvdsIndicates the number of octets that were successfully
received.ro Counter .1.3.6.1.4.1.388.1.5.2.4.25 |
rfEncrypPktsSentsIndicates the number of Encrypted packets transmitted.ro Counter .1.3.6.1.4.1.388.1.5.2.4.26 |
rfEncrypPktsRcvdsIndicates the number of Encrypted packets that were successfully
received.ro Counter .1.3.6.1.4.1.388.1.5.2.4.27 |
apSerialPortStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.388.1.5.2.6 |
apNbrOfDialoutsIndicates the number of dialout attempts by the AP.ro Counter .1.3.6.1.4.1.388.1.5.2.6.1 |
apDialoutFailuresIndicates the number of dialout failures by the AP.ro Counter .1.3.6.1.4.1.388.1.5.2.6.2 |
apNbrOfAnswersIndicates the number of answer attempts by the AP.ro Counter .1.3.6.1.4.1.388.1.5.2.6.3 |
apCurrCallTimeIndicates the length in seconds of current connection
session. Note: the time is relative to the boot time
of this AP.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.388.1.5.2.6.4 |
apLastCallTimeIndicates the length in seconds of last connection
session. Note: the time is relative to the boot time
of this AP.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.388.1.5.2.6.5 |
apWNMPStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.388.1.5.2.7 |
apWNMPCfgPktsIndicates the number of WNMP configuration requests
received from NetVision.ro Counter .1.3.6.1.4.1.388.1.5.2.7.1 |
wEchoRequestsIndicates the number of WNMP Echo Requests received
by this AP.ro Counter .1.3.6.1.4.1.388.1.5.2.7.2 |
wPingRequestsIndicates the number of WNMP ping requests received by
this AP.ro Counter .1.3.6.1.4.1.388.1.5.2.7.3 |
wPktsFromNVsIndicates the number of WNMP packets that were received
from NetVision via this AP.ro Counter .1.3.6.1.4.1.388.1.5.2.7.4 |
wPPktsToNVsIndicates the number of WNMP packets that were sent to
the NetVision via this AP.ro Counter .1.3.6.1.4.1.388.1.5.2.7.5 |
wPassThruEchoesIndicates the number of WNMP packets for other stations
that passed through this AP.ro Counter .1.3.6.1.4.1.388.1.5.2.7.6 |
apMUInfo OBJECT IDENTIFIER .1.3.6.1.4.1.388.1.5.2.8 |
apCurrentMUsIndicates the number of MUs currently associated with
this AP.ro Counter .1.3.6.1.4.1.388.1.5.2.8.1 |
apMaxMUsIndicates the highest number of MUs ever associated
with this AP.ro Counter .1.3.6.1.4.1.388.1.5.2.8.2 |
apTotalAssocsIndicates the total number of associations by all MUs
with this AP.ro Counter .1.3.6.1.4.1.388.1.5.2.8.3 |
apMUTableA table of information for a specific MU associated
with this Access Point.
The current number of entries is 127. SEQUENCE OF ApMUEntry .1.3.6.1.4.1.388.1.5.2.8.4 |
apMUEntryAn entry in the table of information for a specific MU
associated with this Access Point.
A row in this table cannot be created or deleted by
SNMP operations on columns of the table. ApMUEntry .1.3.6.1.4.1.388.1.5.2.8.4.1 |
muIndexSpecific MU information Table index. Range (1..127).ro INTEGER .1.3.6.1.4.1.388.1.5.2.8.4.1.1 |
muMacAddrThe MAC address of the MU associated with this AP.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.388.1.5.2.8.4.1.2 |
muInterfaceIndicates the interface on which this MU is located.
Note: The AP may learn of an MU via the RF network
or from the wired networks such as Ethernet or PPP.
In this release, the AP does not keep track of those
MUs reachable via the Ethernet, but that will change
in future releases.ro Enumeration .1.3.6.1.4.1.388.1.5.2.8.4.1.3 |
muStateIndicates the state of this MU.ro Enumeration .1.3.6.1.4.1.388.1.5.2.8.4.1.4 |
muPowerModeIndicates the MU power mode (Power Save Protocol mode
or Continue Active Mode.)ro Enumeration .1.3.6.1.4.1.388.1.5.2.8.4.1.5 |
muStationIDIndicates the MU station ID.ro INTEGER .1.3.6.1.4.1.388.1.5.2.8.4.1.6 |
muLastAPAddrIndicates the MAC address of the last AP with which
this MU had an association.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.388.1.5.2.8.4.1.7 |
muTotalAssocIndicates the total associations for this MU.ro INTEGER .1.3.6.1.4.1.388.1.5.2.8.4.1.8 |
muAssocStartIndicates when the MU began its current association
with this AP.
Note: Time is represented in seconds and the time
is relative to the boot time of this AP.
This is also true for all the association objects
listed below.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.388.1.5.2.8.4.1.9 |
muLstAssStrtIndicates when the MU began its prior association
with this AP.
If this is the first association with this AP, this
value is zero.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.388.1.5.2.8.4.1.10 |
muLastAssEndIndicates when the MU ended its previous association
with this AP.
If this is the first association with this AP, this
value is zero.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.388.1.5.2.8.4.1.11 |
muNPktsSentsIndicates the number of packets successfully
transmitted to this MU.ro Counter .1.3.6.1.4.1.388.1.5.2.8.4.1.12 |
muNPktsRcvdsIndicates the number of Good Packets received from this
MU.ro Counter .1.3.6.1.4.1.388.1.5.2.8.4.1.13 |
muNBytesSentsIndicates the number of bytes successfully transmitted
to this MU.ro Counter .1.3.6.1.4.1.388.1.5.2.8.4.1.14 |
muNBytesRcvdsIndicates the number of Good Bytes received from this
MU.ro Counter .1.3.6.1.4.1.388.1.5.2.8.4.1.15 |
muNDiscdPktsIndicates the number of received packets discarded
because no buffers.ro Counter .1.3.6.1.4.1.388.1.5.2.8.4.1.16 |
muTmLastDataIndicates the time when the last good packet was
received from this MU.
The packet may be either an ACK, Data, or Poll.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.388.1.5.2.8.4.1.17 |
muPriorityIndicates the Voice/Data priority mode for this MU.ro Enumeration .1.3.6.1.4.1.388.1.5.2.8.4.1.18 |
muSupportedRatesIndicates the supported data rates for this MU.
The unit is MB/second.ro Enumeration .1.3.6.1.4.1.388.1.5.2.8.4.1.19 |
muCurrentXmtRateIndicates the current transmit data rate for this MU.
The unit is MB/second.ro Enumeration .1.3.6.1.4.1.388.1.5.2.8.4.1.20 |
muLastActivityIndicates the time for the last activity for this MU.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.388.1.5.2.8.4.1.21 |
apMUHmAgTableA table of information on Mobile IP Home agent.
The current number of entries is 127. SEQUENCE OF ApMUHATEntry .1.3.6.1.4.1.388.1.5.2.8.5 |
apMUHATEntryAn entry in the table of information on on Mobile IP Home agent.
A row in this table cannot be created or deleted by
SNMP operations on columns of the table. ApMUHATEntry .1.3.6.1.4.1.388.1.5.2.8.5.1 |
muHATMUIpAddrThis is the IP Address of the MU visiting in the foreign network.ro IpAddress .1.3.6.1.4.1.388.1.5.2.8.5.1.1 |
muHATFrAgIpAddrThis is the IP Address of the Foreign agent for the visiting MU.ro IpAddress .1.3.6.1.4.1.388.1.5.2.8.5.1.2 |
apMUFrAgTableA table of information on Mobile IP Foreign agent.
The current number of entries is 127. SEQUENCE OF ApMUFATEntry .1.3.6.1.4.1.388.1.5.2.8.6 |
apMUFATEntryAn entry in the table of information on Mobile IP Foreign agent.
A row in this table cannot be created or deleted by
SNMP operations on columns of the table. ApMUFATEntry .1.3.6.1.4.1.388.1.5.2.8.6.1 |
muFATMUIpAddrThis is the IP Address of the MU visiting in the foreign network.ro IpAddress .1.3.6.1.4.1.388.1.5.2.8.6.1.1 |
muFATHmAgIpAddrThis is the IP Address of the home agent for the visiting MU.ro IpAddress .1.3.6.1.4.1.388.1.5.2.8.6.1.2 |
apKnownAPsTableA table of information on other Access Points known by
this Access Point.
The current number of entries is 32. SEQUENCE OF ApKnownAPsEntry .1.3.6.1.4.1.388.1.5.2.9 |
apKnownAPsEntryAn entry in the table of information on the Known
Access Points.
A row in this table cannot be created or deleted by
SNMP operations on columns of the table. ApKnownAPsEntry .1.3.6.1.4.1.388.1.5.2.9.1 |
apAPMacAddrMac Address of this Known AP.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.388.1.5.2.9.1.1 |
apAPIpAddrIP Address of this Known AP.ro IpAddress .1.3.6.1.4.1.388.1.5.2.9.1.2 |
apHoppingSetHopping Set of this Known AP.ro INTEGER .1.3.6.1.4.1.388.1.5.2.9.1.3 |
apHoppingSeqHopping Sequence of this Known AP.ro INTEGER .1.3.6.1.4.1.388.1.5.2.9.1.4 |
apNbrOfMUsIndicates the number of MUs currently associated with
this known AP.ro INTEGER .1.3.6.1.4.1.388.1.5.2.9.1.5 |
apKBIOSKilobytes sent and received per second by this known
AP on the radio interface.ro INTEGER .1.3.6.1.4.1.388.1.5.2.9.1.6 |
apAwayIndicate that whether this known AP is still alive or
not. If the current AP does not receive WNMP packet
from this known AP within 36 seconds, this known AP is
considered 'AWAY'.ro Enumeration .1.3.6.1.4.1.388.1.5.2.9.1.7 |
ap802dot11ProtocolIndicate that whether this known AP is 802.11
compliant.ro Enumeration .1.3.6.1.4.1.388.1.5.2.9.1.8 |
apFwVerIndicates The firmware revision for this known Access Point.ro DisplayString .1.3.6.1.4.1.388.1.5.2.9.1.9 |
apDSchannelThe current operating frequency channel of the DSSS
PHY. Valid channel numbers are as defined in IEEE
802.11 specification section 15.4.6.2.ro INTEGER .1.3.6.1.4.1.388.1.5.2.9.1.10 |
apFilterStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.388.1.5.2.10 |
apAdrViolationsIndicates the number of Mobile Unit MAC address
violations counted.ro Counter .1.3.6.1.4.1.388.1.5.2.10.1 |
apTypeViolationsIndicates the number of Ethernet packet type violations
counted.ro Counter .1.3.6.1.4.1.388.1.5.2.10.2 |
apWLAPInfo OBJECT IDENTIFIER .1.3.6.1.4.1.388.1.5.2.11 |
apNbrOfWLAPItfsIndicates number of WLAP interfaces established.ro Counter .1.3.6.1.4.1.388.1.5.2.11.1 |
apWLAPStateIndicates the current WLAP state. The state values and
meanings are as follows:
- During power-up initialization:
Initializing(1)
- During WLAP association process:
send-probe(2)
send-assoc-req(3)
send-cfg-bpdu(4)
wait-for-probe(5)
send-probe-rsp(6)
send-assoc-rsp(7)
send-cfg-rsp(8)
receive-root-rsp(10)
- During WLAP operation:
root-ap-lost(12)
disabled(14)
functional(15)
wlap-lost-on-ethernet(16)ro Enumeration .1.3.6.1.4.1.388.1.5.2.11.2 |
apWLAPHopSequenceIndicates the hop sequence of the Root AP followed by
this WLAP.ro INTEGER .1.3.6.1.4.1.388.1.5.2.11.3 |
apRootInterfaceIndicates the WLAP interface leading to the Root AP.ro INTEGER .1.3.6.1.4.1.388.1.5.2.11.4 |
apRootWLAPIDIndicates the WLAP ID of the Root AP. It consists of
2 bytes of priority (Default is 0x8000) and 6 bytes of
MAC address of the Root APro OCTET STRING .1.3.6.1.4.1.388.1.5.2.11.5 |
apRootPathCostIndicates how many hops away the current WLAP is from
the Root AP.ro INTEGER .1.3.6.1.4.1.388.1.5.2.11.6 |
apWLAPIDIndicates the WLAP ID of the current WLAP. It consists
of 2 bytes of priority (Default is 0x8000) and 6 bytes
MAC address of the current WLAPro OCTET STRING .1.3.6.1.4.1.388.1.5.2.11.7 |
apWLAPItfTableA table of wireless AP interfaces information, which
contains four (4) AP-to-AP interfaces. SEQUENCE OF ApWLAPItfEntry .1.3.6.1.4.1.388.1.5.2.11.8 |
apWLAPItfEntryAn entry in the table of wireless AP interfaces
information. ApWLAPItfEntry .1.3.6.1.4.1.388.1.5.2.11.8.1 |
apWLAPItfIDWLAP interface ID. It consists of 1 byte of priority
(Default is 0x80) and 1 byte of interface ID.ro OCTET STRING .1.3.6.1.4.1.388.1.5.2.11.8.1.1 |
apWLAPItfAddrThe MAC address of the associated WLAP on this
interface.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.388.1.5.2.11.8.1.2 |
apWLAPItfStateThe current state of the Wireless AP interface, ie :
Disabled(1), Listening(2), Learning(3), Forwarding(4), or
Blocking(5).ro Enumeration .1.3.6.1.4.1.388.1.5.2.11.8.1.3 |
apWLAPPathCostThe cost to be added to the root path cost field in the
config BPDU (Bridge Protocol Data Unit) received on this
interface in order to determine the cost of the path to
the root WLAP.ro INTEGER .1.3.6.1.4.1.388.1.5.2.11.8.1.4 |
apDsgnatedRootThe unique Root AP ID designated by the Root AP.ro OCTET STRING .1.3.6.1.4.1.388.1.5.2.11.8.1.5 |
apDsgnatedCostThe cost of the path to the Root AP designated by the
Root AP.ro INTEGER .1.3.6.1.4.1.388.1.5.2.11.8.1.6 |
apDsgnatedWLAPThe unique WLAP ID designated by the Root AP.ro OCTET STRING .1.3.6.1.4.1.388.1.5.2.11.8.1.7 |
apDsgnatedItfThe WLAP interface ID designated by the Root AP.ro OCTET STRING .1.3.6.1.4.1.388.1.5.2.11.8.1.8 |
apRetryHistogramTableA table of Retry statistics, which is based on
number of packets with various retries over time.
The current number of entries is 16. SEQUENCE OF ApRetryHistogramEntry .1.3.6.1.4.1.388.1.5.2.12 |
apRetryHistogramEntryAn entry in the table of Retry Histogram, which
is based on number of packets with various
retries over time.
A row in this table cannot be created or deleted by
SNMP operations on columns of the table. ApRetryHistogramEntry .1.3.6.1.4.1.388.1.5.2.12.1 |
apRetryHistogramIndexNumber of retries index. Range (1..16).ro INTEGER .1.3.6.1.4.1.388.1.5.2.12.1.1 |
apNumberOfRetriesPackets with this Number of retries. Range (0..15).ro INTEGER .1.3.6.1.4.1.388.1.5.2.12.1.2 |
apPacketsHistogramCountsCounter for the packets per number of retries.ro Counter .1.3.6.1.4.1.388.1.5.2.12.1.3 |
apDSPerFreqStatTableA table of Radio Per Frequency statistics, which is
based on the historical frequency records used by this
Access Point.
The current number of entries is 78. SEQUENCE OF ApDSPerFreqStatEntry .1.3.6.1.4.1.388.1.5.2.13 |
apDSPerFreqStatEntryAn entry in the table of Radio per frequency
statistics.
A row in this table cannot be created or deleted by
SNMP operations on columns of the table. ApDSPerFreqStatEntry .1.3.6.1.4.1.388.1.5.2.13.1 |
rfDSFrequencyRadio Frequency channel number.ro INTEGER .1.3.6.1.4.1.388.1.5.2.13.1.1 |
rfDSPerFqPktsSentsCounter for the packets sent per frequency.ro Counter .1.3.6.1.4.1.388.1.5.2.13.1.2 |
rfDSPerFqPktsRcvdsCounter for the packets received per frequency.ro Counter .1.3.6.1.4.1.388.1.5.2.13.1.3 |
rfDSPerFqRetriesCounter for the retries per frequency.ro Counter .1.3.6.1.4.1.388.1.5.2.13.1.4 |
apMobileIPStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.388.1.5.2.14 |
apAgentAdSentsCounter for the number agent advertisement sent.ro Counter .1.3.6.1.4.1.388.1.5.2.14.1 |
apRegRequestRcvdsCounter for the number registration request received.ro Counter .1.3.6.1.4.1.388.1.5.2.14.2 |
apRegReplySentsCounter for the number registration reply sent.ro Counter .1.3.6.1.4.1.388.1.5.2.14.3 |
apFaultMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.388.1.5.3 |
apClrAllStatisticsClear all the interface statistics (yes = 1, no = 2).rw Enumeration .1.3.6.1.4.1.388.1.5.3.1 |
apClrMUTableClear the MU Table (yes = 1, no = 2).rw Enumeration .1.3.6.1.4.1.388.1.5.3.2 |
apClrACLClear the Access Control Table (yes = 1, no = 2).rw Enumeration .1.3.6.1.4.1.388.1.5.3.3 |
apClrACLRangeTableClear the Access Control Range Table (yes = 1, no = 2).rw Enumeration .1.3.6.1.4.1.388.1.5.3.4 |
apClrAddrFilterTblClear the Address Filtering Table (yes = 1, no = 2).rw Enumeration .1.3.6.1.4.1.388.1.5.3.5 |
apLdACLFrMUListLoad the Access Control Table from MU Table (yes = 1,
no = 2).rw Enumeration .1.3.6.1.4.1.388.1.5.3.6 |
apModemDialOutCommands the modem to dialout (yes = 1, no = 2).rw Enumeration .1.3.6.1.4.1.388.1.5.3.7 |
apModemHangUpForces the AP to issue a 'hangup' string to the modem
attached to the serial port (yes = 1, no = 2).
This command is meaning-ful only if the AP is
configured for a modem connection on the serial port.
If there is no modem or there is no connection, the
command will be ignored.rw Enumeration .1.3.6.1.4.1.388.1.5.3.8 |
apUpdateFirmwareUpdate the AP firmware through TFTP server. The AP
firmware will be saved in NVRAM (yes = 1, no = 2).
Before issuing this command, set 'apDnLdFileName',
and 'apTFTPServer' to the proper values.rw Enumeration .1.3.6.1.4.1.388.1.5.3.9 |
apDnLdFileNameThe name of the file to be downloaded to the AP.
(Including path name and total up to 49 characters.)
Note: IF DHCP is responded to, that name will take
precedence and overwrite this name.rw DisplayString .1.3.6.1.4.1.388.1.5.3.10 |
apTFTPServerThe IP address for the TFTP Server.
Note: IF DHCP is responded to, that IP address will
take precedence and overwrite this setting.rw IpAddress .1.3.6.1.4.1.388.1.5.3.11 |
apResetAPForces a reset of the AP (yes = 1, no = 2).
Upon reset, the AP clears all the statistics and
restores the last saved configuration information. If
changes are made without being saved, the AP clears
those changes upon reset.rw Enumeration .1.3.6.1.4.1.388.1.5.3.12 |
apHTMLFileNameThe name of the HTML file to be downloaded to
the AP. (Including path name and total up to 49
characters.)
Note: IF DHCP is responded to, that name will
take precedence and overwrite this name.rw DisplayString .1.3.6.1.4.1.388.1.5.3.13 |
apUpdateHTMLFileUpdate the AP HTML file through TFTP server.
The AP HTML file will be saved in NVRAM
(yes = 1, no = 2). Before issuing this command,
set 'apHTMLFileName', and 'apTFTPServer' to the
proper values.rw Enumeration .1.3.6.1.4.1.388.1.5.3.14 |
apDHCPEnableEnables/Disables DHCP mode for the AP. Default is
disabled(2).rw Enumeration .1.3.6.1.4.1.388.1.5.3.15 |
apUpdAllAPsFirmwareUpdate all APs firmware on this network which share
the same NetID through TFTP server. The AP
firmware will be saved in NVRAM (yes = 1, no = 2).
Before issuing this command, set 'apDnLdFileName',
and 'apTFTPServer' to the proper values.rw Enumeration .1.3.6.1.4.1.388.1.5.3.16 |
apUpdAllAPsHTMLFileUpdate all APs HTML file on this network which share
the same NetID through TFTP server.
The AP HTML file will be saved in NVRAM
(yes = 1, no = 2). Before issuing this command,
set 'apHTMLFileName', and 'apTFTPServer' to the
proper values.rw Enumeration .1.3.6.1.4.1.388.1.5.3.17 |
apTFTPUpdBothFilesUpdate Both HTML file and Firmware for this Access Point
The AP HTML file will be saved in NVRAM
(yes = 1, no = 2). Before issuing this command,
set 'apHTMLFileName', and 'apTFTPServer' to the
proper values.rw Enumeration .1.3.6.1.4.1.388.1.5.3.18 |
apHelpURLThe name of the HTML Help file .
(Including path name and total up to 39 characters.)rw DisplayString .1.3.6.1.4.1.388.1.5.3.19 |
apFileUpdateStatusReports the Firmware/HTML file download and
update status.ro Enumeration .1.3.6.1.4.1.388.1.5.3.20 |
apFlashLEDsWhen this command is issued, it forces all status LEDs
on the AP to start flashing. This command is primarily
used for physically locating the AP where multiple APs
are deployed. (yes = 1, no = 2) Default is no.rw Enumeration .1.3.6.1.4.1.388.1.5.3.21 |
apSecurityMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.388.1.5.4 |
apACLViolationsIndicates the number of Access Control violations
occurred.ro Counter .1.3.6.1.4.1.388.1.5.4.1 |
apSaveConfigSaves the current configuration to NVRAM (yes = 1,
no = 2).rw Enumeration .1.3.6.1.4.1.388.1.5.4.2 |
apAccCtrlTableA table of MAC addresses allowed to associate with the
Access Point.
The maximum number of entries in the table is 512. SEQUENCE OF ApAccCtrlEntry .1.3.6.1.4.1.388.1.5.4.3 |
apAccCtrlEntryAn entry in the table of MAC address Access Control.
A row in this table is created by setting the value of
allowedMU to the MAC address of the MU allowed to
associate with this Access Point.
A row in this table is deleted by setting the value of
allowedMU to '000000000000'. ApAccCtrlEntry .1.3.6.1.4.1.388.1.5.4.3.1 |
allowedIndexAccess Control Table index. Range (1..512).ro INTEGER .1.3.6.1.4.1.388.1.5.4.3.1.1 |
allowedMUMU MAC address which is allowed to associate with
this AP.rw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.388.1.5.4.3.1.2 |
apACLRangeTableA table of Access Control Range, which consists of
eight (8) pairs of low and high MAC addresses.
Any Mobile Unit with the MAC address within the range
is allowed to associate with the Access Point.
The maximum number of entries in the table is 8. SEQUENCE OF ApACLRangeEntry .1.3.6.1.4.1.388.1.5.4.4 |
apACLRangeEntryAn entry in the table of MAC address Access Control
Range.
A row in this table is created by first setting the
value of lowMacAddr to the lowest MAC address and then
the value of highMacAddr to the highest MAC address of
a group of Mobile Units allowed to associate with this
Access Point. This sequence of setting is very
important, otherwise a wrong result will occur.
A row in this table is deleted by setting the value of
either lowMacAddr or highMacAddr to '000000000000'. ApACLRangeEntry .1.3.6.1.4.1.388.1.5.4.4.1 |
apACLRangeIndexAccess Control Range Table index. Range (1..8).ro INTEGER .1.3.6.1.4.1.388.1.5.4.4.1.1 |
lowMacAddrThe lowest Mobile Unit MAC address in the range which
is allowed to be associated with this AP.
Note: When setting the ACL range, Both lowMacAddr and
highMacAddr have to be set in order for the ACL range
setting to take effect. lowMacAddr should be entered
first. lowMacAddr < highMacAddrrw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.388.1.5.4.4.1.2 |
highMacAddrThe highest Mobile Unit MAC address in the range which
is allowed to be associated with this AP.
Note: When setting the ACL range, Both lowMacAddr and
highMacAddr have to be set in order for the ACL range
setting to take effect. highMacAddr should be entered
last. highMacAddr > lowMacAddrrw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.388.1.5.4.4.1.3 |
apSaveConfigAllAPsSaves the current configuration to NVRAM
for all APs on this network which share
the same NetID(yes = 1, no = 2).rw Enumeration .1.3.6.1.4.1.388.1.5.4.5 |
apWEPLicenseKeyThis is a license key (a string of 18 alphanumeric characters).
It is arranaged as follows:
xxxx-yyyyyyy-zzzzzzz
xxxx : vendor specific ID code ( 4 alphabetical characters)
-yyyyyyy-zzzzzzz : a string of 14 alphanumeric characters
Note: It is important to insert the hyphens in as shown.
When entered and authenticated by the AP, the Strong(128 bit)
encryption is enabled.
Check the state of ap128bWEPFlag object.rw DisplayString .1.3.6.1.4.1.388.1.5.4.6 |
ap128bWEPFlagWhen enabled, This flag indicates that AP is enabled to
supports strong(128 bit) Encryption. The state of this
flag is internally set only by the AP. when a valid access
code is entered for apWEPLicenseKey object and accepted
the AP will set the state of this flag to enabled.
Default is disabled.ro Enumeration .1.3.6.1.4.1.388.1.5.4.7 |