SWL2MGMT-MIB
The Structure of Layer 2 Network Management Information for the proprietary enterprise.
Main OID:
swL2MgmtMIB.1.3.6.1.4.1.2272.1.201.1.2
286
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
286 total| Object Name |
|---|
swL2MgmtMIBThe Structure of Layer 2 Network Management Information for the
proprietary enterprise. MODULE-IDENTITY .1.3.6.1.4.1.2272.1.201.1.2 |
managementPortLinkUpThe trap is sent whenever the management port is
link up. TRAP-TYPE .1.3.6.1.4.1.2272.1.201.1.2.0.1 |
managementPortLinkDownThe trap is sent whenever the management port is
link down. TRAP-TYPE .1.3.6.1.4.1.2272.1.201.1.2.0.2 |
swL2DevMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.2272.1.201.1.2.1 |
swL2DevInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2272.1.201.1.2.1.1 |
swDevInfoSystemUpTimeThe value of sysUpTime at the time the switch entered its
current operational state. If the current state was entered
prior to the last re-initialization, then this object contains
a zero value. This value is in units of seconds.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.2272.1.201.1.2.1.1.1 |
swDevInfoTotalNumOfPortThe number of ports within this switch. This value is the sum
of the ports within this switch.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.1.1.2 |
swDevInfoNumOfPortInUseThe number of ports in this switch connected to the segment or
the end stations.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.1.1.3 |
swDevInfoConsoleInUseThis usage indication of console system.ro Enumeration .1.3.6.1.4.1.2272.1.201.1.2.1.1.4 |
swDevInfoFrontPanelLedStatusThis object is a set of system LED indications. The first three
octets is defined as system LED. The first LED is primary power
LED. The second LED is redundant power LED. The third LED is
console LED. The other octets following the second octets are
the logical port LED (following dot1dBasePort ordering). Every
two bytes are presented to a port. The first byte is presentd to
the Link/Activity LED. The second byte is presented to the Speed
LED.
Link/Activity LED :
The most significant bit is used for blink/solid:
8 = The LED blinks.
The second significant bit is used for link status:
1 = link fail.
2 = link pass.
Speed LED :
01 = 10Mbps.
02 = 100Mbps.
03 = 1000Mbps.
The four remaining bits are currently unused and must be 0.ro OCTET STRING .1.3.6.1.4.1.2272.1.201.1.2.1.1.5 |
swL2DevCtrlUpDownloadStatestatus of upload/download control. If the value is 'other',
means never firmware updated since device started up.ro Enumeration .1.3.6.1.4.1.2272.1.201.1.2.1.1.6 |
swDevInfoSaveCfgThis object indicates the status of the device configuration.
other(1) - this entry is currently in use but the conditions
under which it will remain so are different from each
of the following values.
proceeding(2) - the device configuration is saving into the
NV-RAM.
ready(3) - the device configuration has been ready to save into
NV-RAM.
failed(4) - The processing of saving device configuration is
failed.ro Enumeration .1.3.6.1.4.1.2272.1.201.1.2.1.1.7 |
swL2DevCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.2272.1.201.1.2.1.2 |
swL2DevCtrlStpStateThis object can be enabled or disabled spanning tree algorithm
during runtime of the system.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.1.2.1 |
swL2DevCtrlIGMPSnoopingThis object indicates layer 2 Internet Group Management
Protocol (IGMP) capture function is enabled or disabled.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.1.2.2 |
swL2DevCtrlRmonStateThis object can be enabled or disabled RMON.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.1.2.3 |
swL2DevCtrlUpDownloadImageFileNameThe name of the image file to be uploaded/Downloaded from the
device to TFTP server when enabling image upload/download
function (by writing swL2DevCtrlUpDownloadImage).rw DisplayString .1.3.6.1.4.1.2272.1.201.1.2.1.2.4 |
swL2DevCtrlUpDownloadImageSourceAddrThe ip address where been uploaded/Downloaded image file.rw IpAddress .1.3.6.1.4.1.2272.1.201.1.2.1.2.5 |
swL2DevCtrlUpDownloadImageImage file upload/download control. After setting, it will
immediately invoke image upload/download function. While
retrieving the value of this object, it always returns 'other'
normally.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.1.2.6 |
swL2DevCtrlSaveCfgAs the object is set to active, the current device
configuration is save into to NV-RAM.If set to normal, do
nothing.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.1.2.7 |
swL2DevCtrlCleanAllStatisticCounterAs the object is set to active, all the statistic counters will
be cleared. If set to normal, do nothing.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.1.2.8 |
swL2DevCtrlStpForwardBPDUThis object allow the forwarding of STP BPDU packets from other
network device or not when STP is disabled on the device.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.1.2.9 |
swL2DevAlarm OBJECT IDENTIFIER .1.3.6.1.4.1.2272.1.201.1.2.1.3 |
swL2DevAlarmNewRootWhen the device has become the new root of the Spanning Tree,
this object decide whether to send a new root trap.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.1.3.1 |
swL2DevAlarmTopologyChangeThis object determine to send a trap or not when the switch
topology was changed. If the object is enabled(3),
the topologyChange trap is sent by the device when any of its
configured ports transitions from the Learning state to the
Forwarding state, or from the Forwarding state to the Blocking
state. For the same port tranition, the device doesn't send the
trap if this object value is disabled or other.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.1.3.2 |
swL2DevAlarmLinkChangeThis object determine to send a trap or not when the link
was changed. If the object is enabled(3), the Link Change
trap is sent by the device when any of its ports link change.
The device doesn't send the trap if this object value is
disabled or other.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.1.3.3 |
swL2UnitMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.2272.1.201.1.2.2 |
swL2UnitCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.2272.1.201.1.2.2.1 |
swL2ModuleMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.2272.1.201.1.2.3 |
swL2PortMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.2272.1.201.1.2.4 |
swL2PortInfoTableA table that contains information about every port. SEQUENCE OF SwL2PortInfoEntry .1.3.6.1.4.1.2272.1.201.1.2.4.1 |
swL2PortInfoEntryA list of information for each port of the device. SwL2PortInfoEntry .1.3.6.1.4.1.2272.1.201.1.2.4.1.1 |
swL2PortInfoPortIndexThis object indicates the module's port number.(1..Max port
number in the module)ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.4.1.1.1 |
swL2PortInfoUnitIndexIndicates ID of the unit in the devicero INTEGER .1.3.6.1.4.1.2272.1.201.1.2.4.1.1.2 |
swL2PortInfoTypeThis object indicates the connector type of this port.ro Enumeration .1.3.6.1.4.1.2272.1.201.1.2.4.1.1.3 |
swL2PortInfoLinkStatusThis object indicates the port link status.ro Enumeration .1.3.6.1.4.1.2272.1.201.1.2.4.1.1.4 |
swL2PortInfoNwayStatusThis object indicates the port speed and duplex mode.ro Enumeration .1.3.6.1.4.1.2272.1.201.1.2.4.1.1.5 |
swL2PortCtrlTableA table that contains control information about every port. SEQUENCE OF SwL2PortCtrlEntry .1.3.6.1.4.1.2272.1.201.1.2.4.2 |
swL2PortCtrlEntryA list of control information for each port of the device. SwL2PortCtrlEntry .1.3.6.1.4.1.2272.1.201.1.2.4.2.1 |
swL2PortCtrlPortIndexThis object indicates the module's port number.(1..Max port
number in the module)ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.4.2.1.1 |
swL2PortCtrlUnitIndexIndicates ID of the unit in the devicero INTEGER .1.3.6.1.4.1.2272.1.201.1.2.4.2.1.2 |
swL2PortCtrlAdminStateThis object decide the port enabled or disabled.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.4.2.1.3 |
swL2PortCtrlNwayStateChose the port speed, duplex mode, and N-Way function mode.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.4.2.1.4 |
swL2PortCtrlFlowCtrlStateThe flow control mechanism is different between full duplex
mode and half duplex mode. For half duplex mode, the jamming
signal is asserted. For full duplex mode, IEEE 802.3x flow
control function sends PAUSE frames and receives PAUSE frames.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.4.2.1.5 |
swL2PortCtrlAddressLearningStateThis object decide the address learning state on this port is
enabled or disabled.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.4.2.1.6 |
swL2PortUtilTableA table that contains information of utilization about every
port. SEQUENCE OF SwL2PortUtilEntry .1.3.6.1.4.1.2272.1.201.1.2.4.3 |
swL2PortUtilEntryA list of information of utilization for each port of the device. SwL2PortUtilEntry .1.3.6.1.4.1.2272.1.201.1.2.4.3.1 |
swL2PortUtilPortIndexThis object indicates the module's port number.(1..Max port
number in the module)ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.4.3.1.1 |
swL2PortUtilTxSecIndicates how many packets transmitted per second.ro Gauge32 .1.3.6.1.4.1.2272.1.201.1.2.4.3.1.2 |
swL2PortUtilRxSecIndicates how many packets received per second.ro Gauge32 .1.3.6.1.4.1.2272.1.201.1.2.4.3.1.3 |
swL2PortUtilUtilizationThis object indicates the port utilization.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.4.3.1.4 |
swL2FilterMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.2272.1.201.1.2.6 |
swL2FilterAddrConfig OBJECT IDENTIFIER .1.3.6.1.4.1.2272.1.201.1.2.6.1 |
swL2FilterAddrMaxSupportedEntriesMaximum number of entries in the MAC address filtering table
(swL2FilterAddrCtrlTable).ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.6.1.1 |
swL2FilterAddrCurrentTotalEntriesCurrent applied number of entries in the MAC address filtering
table.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.6.1.2 |
swL2FilterAddrCtrlTableThis table defines information for the device to filter packets
with specific MAC address (either as the DA and/or as the SA).
The MAC address can be a unicast address or a multicast address.
This table has higher priority than both static FDB table and
IGMP table. It means that if a MAC address appears on this table
also appears on the static FDB table, the device will use the
information provide by this table to process the packet. SEQUENCE OF SwL2FilterAddrCtrlEntry .1.3.6.1.4.1.2272.1.201.1.2.6.1.3 |
swL2FilterAddrCtrlEntryA list of information about a specific unicast/multicast MAC
address for which the switch has filtering information. SwL2FilterAddrCtrlEntry .1.3.6.1.4.1.2272.1.201.1.2.6.1.3.1 |
swL2FilterAddrMacIndexThis object indicates a unicast/multicast MAC address for which
the switch has filtering information. But if the
swL2FilterAddrState = src-addr then the object can not be a
multicast MAC address.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.2272.1.201.1.2.6.1.3.1.1 |
swL2FilterAddrStateThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions
under which it will remain so are different from each of the
following values.
dst-addr(2) - recieved frames's destination address are
currently used to be filtered as it meets with the MAC
address entry of the table.
src-addr(3) - recieved frames's source address are currently
used to be filtered as it meets with the MAC address entry
of the table.
dst-src-addr(4) - recieved frames's destination address or
source address are currently used to be filtered as it meets
with the MAC address entry of the table.
invalid(5) - writing this value to the object, and then the
corresponding entry will be removed from the table.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.6.1.3.1.2 |
swL2VlanMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.2272.1.201.1.2.7 |
swL2StaticVlanTableA table containing static configuration information for each
VLAN configured into the device by (local or network)
management. SEQUENCE OF SwL2StaticVlanEntry .1.3.6.1.4.1.2272.1.201.1.2.7.1 |
swL2StaticVlanEntryStatic information for a VLAN configured into the device by
(local or network) management. SwL2StaticVlanEntry .1.3.6.1.4.1.2272.1.201.1.2.7.1.1 |
swL2StaticVlanIndexA value that uniquely identifies the Virtual LAN associated
with this entry.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.7.1.1.1 |
swL2StaticVlanNameAn administratively-assigned name for this VLAN.rw DisplayString .1.3.6.1.4.1.2272.1.201.1.2.7.1.1.2 |
swL2StaticVlanTypeThe type of VLAN, distinguished according to the policy used
to define its port membership.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.7.1.1.3 |
swL2StaticVlanProtocolIdThe protocol identifier of this VLAN. This value is meaningful
only if swL2StaticVlanType is equal to byProtocolId(3). For
other VLAN types it should have the value none(0).rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.7.1.1.4 |
swL2StaticVlanIpSubnetAddrThe IP subnet address of this VLAN. This value is meaningful
only if rcVlanType is equal to byIpSubnet(2). For other VLAN
types it should have the value 0.0.0.0.rw IpAddress .1.3.6.1.4.1.2272.1.201.1.2.7.1.1.5 |
swL2StaticVlanIpSubnetMaskThe IP subnet mask of this VLAN. This value is meaningful only
if rcVlanType is equal to byIpSubnet(2). For other VLAN types
it should have the value 0.0.0.0.rw IpAddress .1.3.6.1.4.1.2272.1.201.1.2.7.1.1.6 |
swL2StaticVlanUserDefinedPidWhen swL2StaticVlanProtocolId is set to userDefined(16) in a
protocol-based VLAN, this field represents the 16-bit user
defined protocol identifier. Otherwise, this object should be
zero.rw OCTET STRING .1.3.6.1.4.1.2272.1.201.1.2.7.1.1.7 |
swL2StaticVlanEncapThis value is meaningful only if swL2StaticVlanProtocolId is
set to userDefined(16). Otherwise, this object should be
un-used(5). If If this set to ethernet2(2), the Detagged Frame
uses Type-encapsulated 802.3 format. If this set to llc(3), the
Detagged Frame contains both a DSAP and an SSAP address field
in the positions. If this set to snap(4), the Detagged Frame is
of the format specified by IEEE Std. 802.1H for the encoding of
an IEEE 802.3 Type Field in an 802.2/SNAP header.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.7.1.1.8 |
swL2StaticVlanUserPriorityUser priority level. This value is meaningful only if
swL2StaticVlanType is set to byIpSubnet(2) or byProtocolId(3).rw INTEGER (0|4|6|7) .1.3.6.1.4.1.2272.1.201.1.2.7.1.1.9 |
swL2StaticVlanEgressPortsThe set of ports which are permanently assigned to the
egress list for this VLAN by management. The default value of
this object is a string of zeros of appropriate length.rw PortList .1.3.6.1.4.1.2272.1.201.1.2.7.1.1.10 |
swL2StaticVlanUntaggedPortsThe set of ports which should transmit egress packets
for this VLAN as untagged. The default value of this
object for the default VLAN is a string of appropriate length
including all ports. There is no specified default for other
VLANs.rw PortList .1.3.6.1.4.1.2272.1.201.1.2.7.1.1.11 |
swL2StaticVlanStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2272.1.201.1.2.7.1.1.12 |
swL2StaticVlanIpSubnetArpClassIdThis object indicates the ARP classification ID. If the
swL2StaticVlanType is not byIpSubnet(2), this value must be 0.
If the swL2StaticVlanType is byIpSubnet(2), the range of this
object is 1 to 4094. This object is useful when create the
first IpSubnet entry, and not allow to modify.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.7.1.1.13 |
swL2VlanPortTableA table containing per port control and status information for
VLAN configuration in the device. SEQUENCE OF SwL2VlanPortEntry .1.3.6.1.4.1.2272.1.201.1.2.7.2 |
swL2VlanPortEntryInformation controlling VLAN configuration for a port
on the device. SwL2VlanPortEntry .1.3.6.1.4.1.2272.1.201.1.2.7.2.1 |
swL2VlanPortIndexAn unique index used to identify a particular port in the
system.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.7.2.1.1 |
swL2VlanPortPvidThe PVID, the VLAN ID assigned to untagged frames or Priority-
Tagged frames received on this port.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.7.2.1.2 |
swL2VlanPortIngressCheckingWhen this is enabled(3) the device will discard incoming
frames for VLANs which do not include this Port in its
Member set. When disabled(2), the port will accept all
incoming frames.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.7.2.1.3 |
swL2TrunkMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.2272.1.201.1.2.8 |
swL2TrunkMaxSupportedEntriesMaximum number of entries in the trunk configuration table
(swL2TrunkCtrlTable).ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.8.1 |
swL2TrunkCurrentNumEntriesCurrent actived number of entries in the trunk configuration
table.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.8.2 |
swL2TrunkCtrlTableThis table specifys which ports group a set of ports(up to 8)
into a single logical link. SEQUENCE OF SwL2TrunkCtrlEntry .1.3.6.1.4.1.2272.1.201.1.2.8.3 |
swL2TrunkCtrlEntryA list of information specifies which ports group a set of
ports(up to 8) into a single logical link. SwL2TrunkCtrlEntry .1.3.6.1.4.1.2272.1.201.1.2.8.3.1 |
swL2TrunkIndexThe index of logical port trunk. The trunk group number depend
on the existence of unit and module.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.8.3.1.1 |
swL2TrunkNameThe name of logical port trunk.rw DisplayString .1.3.6.1.4.1.2272.1.201.1.2.8.3.1.2 |
swL2TrunkMasterPortThe object indicates the master port number of the port trunk
entry. When using Port Trunk, you can not configure the other
ports of the group except the master port.
Their configuration must be same as the master port (e.g. speed,
duplex, enabled/disabled, flow control, and so on).rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.8.3.1.3 |
swL2TrunkMemberIndicate how many number of ports is included in this Trunk.
The trunk port number depend on the existence of module.
The maximum number of ports is 4 for one trunks.rw PortList .1.3.6.1.4.1.2272.1.201.1.2.8.3.1.4 |
swL2TrunkFloodingPortThe object indicates the flooding port number of the port trunk
entry. The first port of the trunk is implicitly configured to
be the flooding port.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.8.3.1.5 |
swL2TrunkStateThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions
under which it will remain so are different from each of
the following values.
disabled(2) - the port trunk disabled.
enabled(3) - the port trunk enabled.
invalid(4) - writing this value to the object, and then the
corresponding entry will be removed from the table.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.8.3.1.6 |
swL2TrunkBPDU8600InterStateThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions
under which it will remain so are different from each of
the following values.
disabled(2) - the trunk member doesn't send BPDU.
enabled(3) - the trunk member can send BPDU.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.8.3.1.7 |
swL2TrunkAlgorithmThis object configures to part of the packet examined by the
switch when selecting the egress port for transmitting
load-sharing data. This feature is only available using the
address-based load-sharing algorithm.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.8.4 |
swL2MirrorMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.2272.1.201.1.2.9 |
swL2MirrorLogicTargetPortThis object indicates switch which port will sniff another
port. A trunk port member cannot be configured as a target
Snooping port. The port number is the sequential (logical)
number which is also applied to bridge MIB, etc.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.9.1 |
swL2MirrorPortSourceIngressThe represent the ingress into the source port packet to
sniffed.rw PortList .1.3.6.1.4.1.2272.1.201.1.2.9.2 |
swL2MirrorPortSourceEgressThe represent the egress from the source port packet to
sniffed.rw PortList .1.3.6.1.4.1.2272.1.201.1.2.9.3 |
swL2MirrorPortStateThis object indicates the port mirroring state.
other(1) - this entry is currently in use but the conditions
under which it will remain so are different from each of the
following values.
disabled(2) - writing this value to the object, and then the
corresponding entry will be removed from the table.
enabled(3) - this entry is reside in the table.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.9.4 |
swL2IGMPMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.2272.1.201.1.2.10 |
swL2IGMPMaxSupportedVlansMaximum number of Vlans in the layer 2 IGMP control table
(swL2IGMPCtrlTable).ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.10.1 |
swL2IGMPMaxIpGroupNumPerVlanMaximum number of multicast ip group per Vlan in the layer 2
IGMP information table (swL2IGMPQueryInfoTable).ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.10.2 |
swL2IGMPCtrlTableThe table controls the Vlan's IGMP function. Its scale depends
on current VLAN state (swL2VlanInfoStatus). If VLAN is disabled
mode, there is only one entry in the table, with index 1. If
VLAN is in Port-Base or 802.1q mode, the number of entries can
be up to 12, with index range from 1 to 12. SEQUENCE OF SwL2IGMPCtrlEntry .1.3.6.1.4.1.2272.1.201.1.2.10.3 |
swL2IGMPCtrlEntryThe entry in IGMP control table (swL2IGMPCtrlTable). The entry
is effective only when IGMP capture switch
(swL2DevCtrlIGMPSnooping) is enabled. SwL2IGMPCtrlEntry .1.3.6.1.4.1.2272.1.201.1.2.10.3.1 |
swL2IGMPCtrlVidThis object indicates the IGMP control entry's VLAN id. If VLAN
is disabled, the Vid is always 0 and cannot be changed by
management users. If VLAN is in Port-Base mode, the Vid is
arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode,
the Vid setting can vary from 1 to 4094 by management user, and
the Vid in each entry must be unique in the IGMP Control Table.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.10.3.1.1 |
swL2IGMPQueryIntervalThe frequency at which IGMP Host-Query packets are
transmitted on this switch.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.10.3.1.2 |
swL2IGMPMaxResponseTimeThe maximum query response time on this switch.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.10.3.1.3 |
swL2IGMPRobustnessThe Robustness Variable allows tuning for the expected
packet loss on a subnet. If a subnet is expected to be
lossy, the Robustness Variable may be increased. IGMP is
robust to (Robustness Variable-1) packet losses.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.10.3.1.4 |
swL2IGMPLastMemberQueryIntervalThe Last Member Query Interval is the Max Response Time
inserted into Group-Specific Queries sent in response to
Leave Group messages, and is also the amount of time between
Group-Specific Query messages.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.10.3.1.5 |
swL2IGMPHostTimeoutThe timer value for sending IGMP query packet when none was
sent by the host in the LAN. The timer works in per-VLAN basis.
Our device will be activated to send the query message if the
timer is expired. Please reference RFC2236-1997.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.10.3.1.6 |
swL2IGMPRouteTimeoutThe Router Timeout is how long a host must wait after hearing
a Query before it may send any IGMPv2 messages.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.10.3.1.7 |
swL2IGMPLeaveTimerWhen a querier receives a Leave Group message for a group that
has group members on the reception interface, it sends
Group-Specific Queries every swL2IGMPLeaveTimer to the group
being left.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.10.3.1.8 |
swL2IGMPQueryStateThis object decide the IGMP query enabled or disabled.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.10.3.1.9 |
swL2IGMPCurrentStateThis object indicates the current IGMP query state.ro Enumeration .1.3.6.1.4.1.2272.1.201.1.2.10.3.1.10 |
swL2IGMPCtrlStateThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
disabled(2) - IGMP funtion is disabled for this entry.
enabled(3) - IGMP funtion is enabled for this entry.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.10.3.1.11 |
swL2IGMPQueryInfoTableThe table contains the number current IGMP query packets which
is captured by this device, as well as the IGMP query packets
sent by the device. SEQUENCE OF SwL2IGMPQueryInfoEntry .1.3.6.1.4.1.2272.1.201.1.2.10.4 |
swL2IGMPQueryInfoEntryInformation about current IGMP query information, provided that
swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN
entry are all enabled. SwL2IGMPQueryInfoEntry .1.3.6.1.4.1.2272.1.201.1.2.10.4.1 |
swL2IGMPInfoVidThis object indicates the Vid of associated IGMP info table
entry. It follows swL2IGMPCtrlVid in the associated entry of
IGMP control table (swL2IGMPCtrlTable).ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.10.4.1.1 |
swL2IGMPInfoQueryCountThis object indicates the number of query packets received
since the IGMP function enabled, in per-VLAN basis.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.10.4.1.2 |
swL2IGMPInfoTxQueryCountThis object indicates the send count of IGMP query messages, in
per-VLAN basis. In case of IGMP timer expiration, the switch
sends IGMP query packets to related VLAN member ports and
increment this object by 1.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.10.4.1.3 |
swL2IGMPGroupTableThe table containing current IGMP information which captured by
this device, provided that swL2DevCtrlIGMPSnooping and
swL2IGMPCtrlState of associated VLAN entry are all enabled. Note
that the priority of IGMP table entries is lower than Filtering
Table, i.e. if there is a table hash collision between the
entries of IGMP Table and Filtering Table inside the switch H/W
address table, then Filtering Table entry overwrite the
colliding entry of IGMP Table. See swL2FilterMgmt description
also. SEQUENCE OF SwL2IGMPGroupEntry .1.3.6.1.4.1.2272.1.201.1.2.10.5 |
swL2IGMPGroupEntryInformation about current IGMP information which captured by
this device, provided that swL2DevCtrlIGMPSnooping and
swL2IGMPCtrlState of associated VLAN entry are all enabled. SwL2IGMPGroupEntry .1.3.6.1.4.1.2272.1.201.1.2.10.5.1 |
swL2IGMPVidThis object indicates the Vid of individual IGMP table entry.
It shows the Vid of IGMP report information captured on
network.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.10.5.1.1 |
swL2IGMPGroupIpAddrThis object is identify group ip address which is captured from
IGMP packet, in per-Vlan basis.ro IpAddress .1.3.6.1.4.1.2272.1.201.1.2.10.5.1.2 |
swL2IGMPMacAddrThis object is identify mac address which is corresponding
to swL2IGMPGroupIpAddr, in per-Vlan basis.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.2272.1.201.1.2.10.5.1.3 |
swL2IGMPPortMapThis object indicates which ports are belong to the same
multicast group, in per-Vlan basis. Each multicast group has a
octect string to indicate with port map. The most significant
bit represents the lowest numbered port, and the least
significant bit represents the highest numbered port. Thus, each
port of the switch is represented by a single bit within the
value of this object. If that bit has a value of '1' then that
port is included in the set of ports; the port is not included
if its bit has a value of '0'(Note that the setting of the bit
corresponding to the port from which a frame is received is
irrelevant). The 4 octets is represent one unit port according
its logic port. If the unit less 32 port, the other port don't
care just fill zero.ro PortList .1.3.6.1.4.1.2272.1.201.1.2.10.5.1.4 |
swL2IGMPIpGroupReportCountThis object indicate how much report packet was receive by our
device corresponding with this entry from IGMP function enabled,
in per-Vlan basis.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.10.5.1.5 |
swL2IGMPForwardTableThe table containing current IGMP forwarding information which
captured by this device, provided that swL2DevCtrlIGMPSnooping
and swL2IGMPCtrlState of associated VLAN entry are all enabled.
Note that the priority of IGMP table entries is lower than
Filtering Table, i.e. if there is a table hash collision between
the entries of IGMP Table and Filtering Table inside the switch
H/W address table, then Filtering Table entry overwrite the
colliding entry of IGMP Table. See swL2FilterMgmt description
also. SEQUENCE OF SwL2IGMPForwardEntry .1.3.6.1.4.1.2272.1.201.1.2.10.6 |
swL2IGMPForwardEntryInformation about current IGMP forwarding information which
captured by this device, provided that swL2DevCtrlIGMPSnooping
and swL2IGMPCtrlState of associated VLAN entry are all enabled. SwL2IGMPForwardEntry .1.3.6.1.4.1.2272.1.201.1.2.10.6.1 |
swL2IGMPForwardVidThis object indicates the Vid of individual IGMP table entry.
It shows the Vid of IGMP report forward information captured on
network.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.10.6.1.1 |
swL2IGMPForwardGroupIpAddrThis object is identify group ip address which is captured from
IGMP packet, in per-Vlan basis.ro IpAddress .1.3.6.1.4.1.2272.1.201.1.2.10.6.1.2 |
swL2IGMPForwardPortMapThis object indicates which ports are belong to the same
multicast group, in per-Vlan basis. Each multicast group has a
octect string to indicate with port map. The most significant
bit represents the lowest numbered port, and the least
significant bit represents the highest numbered port. Thus, each
port of the switch is represented by a single bit within the
value of this object. If that bit has a value of '1' then that
port is included in the set of ports; the port is not included
if its bit has a value of '0'(Note that the setting of the bit
corresponding to the port from which a frame is received is
irrelevant). The 4 octets is represent one unit port according
its logic port. If the unit less 32 port, the other port don't
care just fill zero.ro PortList .1.3.6.1.4.1.2272.1.201.1.2.10.6.1.3 |
swL2IGMPRPTableThe table allows you to designate a range of ports as being
connected to multicast-enabled routers. This will ensure that
all packets with such a router as its destination will reach the
multicast-enabled router, regardless of protocol, etc. SEQUENCE OF SwL2IGMPRPEntry .1.3.6.1.4.1.2272.1.201.1.2.10.7 |
swL2IGMPRPEntryA list of swL2IGMPRPTable. SwL2IGMPRPEntry .1.3.6.1.4.1.2272.1.201.1.2.10.7.1 |
swL2IGMPRPVidThe Vid of the VLAN on which the router port resides.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.10.7.1.1 |
swL2IGMPRPStaticRouterPortSpecifies a range of ports which will be configured as router
ports.rw PortList .1.3.6.1.4.1.2272.1.201.1.2.10.7.1.2 |
swL2IGMPRPDynamicRouterPortDisplays router ports that have been dynamically configued.ro PortList .1.3.6.1.4.1.2272.1.201.1.2.10.7.1.3 |
swL2IGMPMulticastRouterOnlyThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
disabled(2) - the switch forwards all mulitcast traffic to any IP
router.
enabled(3) - the switch will forward all multicast traffic to the
multicast router, only.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.10.8 |
swL2IGMPGroupPortTableThis table describe the detail information of the member ports
of the swL2IGMPGroupTable. SEQUENCE OF SwL2IGMPGroupPortEntry .1.3.6.1.4.1.2272.1.201.1.2.10.9 |
swL2IGMPGroupPortEntryInformation about member ports of current swL2IGMPGroupTable. SwL2IGMPGroupPortEntry .1.3.6.1.4.1.2272.1.201.1.2.10.9.1 |
swL2IGMPPortMemberThis object indicates which ports are belong to the same
multicast group, in per-Vlan basis, in swL2IGMPGroupTable.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.10.9.1.1 |
swL2IGMPPortAgingTimeThis object indicate the aging out timer. This value is in
units of seconds.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.10.9.1.2 |
swL2IGMPMulticastFilterThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
disabled(2) - the un-registered multicast traffic will be flooded.
enabled(3) - the un-registered multicast traffic will be filtered.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.10.10 |
swL2TrafficMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.2272.1.201.1.2.12 |
swL2TrafficCtrlTableThis table specifys the storm traffic control configuration. SEQUENCE OF SwL2TrafficCtrlEntry .1.3.6.1.4.1.2272.1.201.1.2.12.1 |
swL2TrafficCtrlEntryA list of information specifies the storm traffic control
configuration. SwL2TrafficCtrlEntry .1.3.6.1.4.1.2272.1.201.1.2.12.1.1 |
swL2TrafficCtrlGroupIndexThe index of logical port trunk. The trunk group number depend
on the existence of unit and module.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.12.1.1.1 |
swL2TrafficCtrlUnitIndexIndicates ID of the unit in the devicero INTEGER .1.3.6.1.4.1.2272.1.201.1.2.12.1.1.2 |
swL2TrafficCtrlBMStormthresholdThis object to decide how much thousand packets per second
broadcast/multicast (depend on swL2TrafficCtrlBcastStormCtrl,
swL2TrafficCtrlMcastStormCtrl or swL2TrafficCtrlDlfStormCtrl
objects whether is enabled) will active storm control. Whenever
a port reaches its configured amount of packets in the one
second time interval, the device will start dropping that type
of packet, until the time interval has expired. Once the time
interval has expired, the device will start forwarding that type
of packet.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.12.1.1.3 |
swL2TrafficCtrlBcastStormCtrlThis object indicates broadcast storm control function is
enabled or disabled.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.12.1.1.4 |
swL2TrafficCtrlMcastStormCtrlThis object indicates multicast storm control function is
enabled or disabled.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.12.1.1.5 |
swL2TrafficCtrlDlfStormCtrlThis object indicates destination lookup fail function is
enabled or disabled.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.12.1.1.6 |
swL2QosMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.2272.1.201.1.2.13 |
swL2QosSchedulingTableThe switch contains 4 hardware priority queues. Incoming packets
must be mapped to one of these four queues. Each hardware queue
will transmit all of the packets in its buffer before allowing
the next lower priority queue to transmit its packets. When the
lowest hardware priority queue has finished transmitting all of
its packets, the highest hardware priority queue can again
transmit any packets it may have received. SEQUENCE OF SwL2QosSchedulingEntry .1.3.6.1.4.1.2272.1.201.1.2.13.1 |
swL2QosSchedulingEntryA list of information specifies the Qos output scheduling Table. SwL2QosSchedulingEntry .1.3.6.1.4.1.2272.1.201.1.2.13.1.1 |
swL2QosSchedulingClassIdThis specifies which of the four hardware priority queues. The
four hardware priority queues are identified by number, from 0
to 3, with the 0 queue being the lowest priority.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.13.1.1.1 |
swL2QosSchedulingMaxPktsSpecifies the maximium number of packets the above specified
hardware priority queue will be allowed to transmit before
allowing the next lowest priority queue to transmit its packets.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.13.1.1.2 |
swL2QosSchedulingMaxLatencySpecifies the maximum amount of time the above specified hardware
priority queue will be allowed to transmit packets before allowing
the next lowest hardware priority queue to begin transmitting
its packets. A value between 0 and 255 can be specified. With
this value multiplied by 16 ms to arrive at the total allowed
time for the queue to transmit packets.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.13.1.1.3 |
swL2QosPriorityTableThis table display the current priority settings on the switch. SEQUENCE OF SwL2QosPriorityEntry .1.3.6.1.4.1.2272.1.201.1.2.13.2 |
swL2QosPriorityEntryA list of information display the current priority settings on
the switch. SwL2QosPriorityEntry .1.3.6.1.4.1.2272.1.201.1.2.13.2.1 |
swL2QosPriorityTypeThese parameters define what characteristics an incoming packet
must meet. One or more of the above parameters must be defined.ro Enumeration .1.3.6.1.4.1.2272.1.201.1.2.13.2.1.1 |
swL2QosPriorityValueThis object must match with swL2QosPriorityType. If the type is
type-dscp(2), the range of this object is 0~63. If the type is
type-8021p(3), the range of this object is 0~7. If the type is
type-tcp(4) or type-udp(5), the range of this object is 1~65535.ro OCTET STRING .1.3.6.1.4.1.2272.1.201.1.2.13.2.1.2 |
swL2QosPriorityPriorityAllows to specify a priority value to be written to the 802.1p
priority field of an incoming packet that meets the criteria.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.13.2.1.3 |
swL2QosPriorityPriorityStateThis object indicates 802.1p priority function is enabled or
disabled.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.13.2.1.4 |
swL2QosPriorityReplaceDscpAllows to specify a value to be written to the DSCP field of an
incoming packet that meets the criteria.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.13.2.1.5 |
swL2QosPriorityReplaceDscpStateThis object indicates DSCP function is enabled or disabled.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.13.2.1.6 |
swL2QosPriorityReplacePriorityThis object indicates the 802.1p user priority with the priority
specified above will be replaced or not.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.13.2.1.7 |
swL2QosPriorityStateThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions
under which it will remain so are different from each of
the following values.
invalid(2) - writing this value to the object, and then the
corresponding entry will be removed from the table.
valid(3) - this entry is reside in the table.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.13.2.1.8 |
swL2MgmtMIBTraps OBJECT IDENTIFIER .1.3.6.1.4.1.2272.1.201.1.2.14 |
swL2StormCtrlMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.2272.1.201.1.2.15 |
swL2StormCtrlTableThis table specifys the storm traffic control configuration. SEQUENCE OF SwL2StormCtrlEntry .1.3.6.1.4.1.2272.1.201.1.2.15.1 |
swL2StormCtrlEntryA list of information specifies the storm traffic control
configuration. SwL2StormCtrlEntry .1.3.6.1.4.1.2272.1.201.1.2.15.1.1 |
swL2StormCtrlPortIndexThe index of logical port.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.15.1.1.1 |
swL2StormCtrlBcastStormCtrlThis object indicates broadcast storm control function is
enabled or disabled.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.15.1.1.2 |
swL2StormCtrlMcastStormCtrlThis object indicates multicast storm control function is
enabled or disabled.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.15.1.1.3 |
swL2StormCtrlBMStormThresholdThis object to decide how much percentage packets per second
broadcast/multicast (depend on swL2StormCtrlBcastStormCtrl or
swL2StormCtrlMcastStormCtrl objects whether is enabled) will
active storm control. Whenever a port reaches its configured
percent of packets in the one second time interval, the device
will start dropping that type of packet, until the time interval
has expired. Once the time interval has expired, the device will
start forwarding that type of packet.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.15.1.1.4 |
swL2StormCtrlDlfStateThis object indicates destination lookup fail function is
enabled or disabled.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.15.2 |
swL2StormCtrlDlfThresholdThis object to decide how much packets per second destination
lookup fail (depend on swL2StormCtrlDlfState objects whether is
enabled) will active storm control. Whenever the device reaches
its configured packets in the one second time interval, the
device will start dropping that type of packet, until the time
interval has expired. Once the time interval has expired, the
device will start forwarding that type of packet. This value
must be the multiples of 8192.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.15.3 |
swL2CpuRateLimitTableThis table specifys the CPU rate limit per port. Once too much
broadcast/multicast traffic, exceed CP-Limit, comes in from a
port, the port state will be disabled. SEQUENCE OF SwL2CpuRateLimitEntry .1.3.6.1.4.1.2272.1.201.1.2.15.4 |
swL2CpuRateLimitEntryA list of information specifies the CPU rate limit of the port
configuration. SwL2CpuRateLimitEntry .1.3.6.1.4.1.2272.1.201.1.2.15.4.1 |
swL2CpuRateLimitPortIndexThe index of logical port.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.15.4.1.1 |
swL2CpuRateLimitStateThis object indicates CPU rate limit function is enabled or
disabled.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.15.4.1.2 |
swL2CpuRateLimitBcastThresholdThis object to decide how much packets per second broadcast
will active traffic control. Whenever a port reaches its
configured packets in the one second time interval, the port
will be disabled.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.15.4.1.3 |
swL2CpuRateLimitMcastThresholdThis object to decide how much packets per second multicast
will active traffic control. Whenever a port reaches its
configured packets in the one second time interval, the port
will be disabled.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.15.4.1.4 |
swL2CpuUtilizationThe utilization of CPU.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.15.5 |
swL2ACLQosMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.2272.1.201.1.2.16 |
swL2ACLQosTemplate1ModeThis object decide the operate mode of template_1.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.1 |
swL2ACLQosTemplate2ModeThis object decide the operate mode of template_2.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.2 |
swL2ACLQosFlowClassifierTableThis table specifys the template of flow classifier. SEQUENCE OF SwL2ACLQosFlowClassifierEntry .1.3.6.1.4.1.2272.1.201.1.2.16.3 |
swL2ACLQosFlowClassifierEntryA list of information specifies the template of flow classifier. SwL2ACLQosFlowClassifierEntry .1.3.6.1.4.1.2272.1.201.1.2.16.3.1 |
swL2ACLQosFlowClassifierTemplateIdThe index of template ID.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.16.3.1.1 |
swL2ACLQosFlowClassifierCurrentModeThe current operated mode of this template.ro Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.3.1.2 |
swL2ACLQosFlowClassifierSecuritySrcMaskThis object indicates a source IP subnet rule for the switch.
If the swL2ACLQosFlowClassifierCurrentMode is not security(2),
then this object must be 0.0.0.0.rw IpAddress .1.3.6.1.4.1.2272.1.201.1.2.16.3.1.3 |
swL2ACLQosFlowClassifierQosFlavorThese parameters define what characteristics an incoming packet
must meet. One or more of the above parameters must be defined.
If the swL2ACLQosFlowClassifierCurrentMode is not qos(3), then
this object must be flavor-un-used(6).rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.3.1.4 |
swL2ACLQosFlowClassifierL4SwitchTCPDstIpThis object indicate the destination ipaddress in the configured
L4 TCP-session rule entries must be checked or not. If the
swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then
this object must be un-used(3).rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.3.1.5 |
swL2ACLQosFlowClassifierL4SwitchTCPSrcIpThis object indicate the source ipaddress in the configured L4
TCP-session rule entries must be checked or not. If the
swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then
this object must be un-used(3).rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.3.1.6 |
swL2ACLQosFlowClassifierL4SwitchTCPTosThis object indicate the type of service in the configured L4
TCP-session rule entries must be checked or not. If the
swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then
this object must be un-used(3).rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.3.1.7 |
swL2ACLQosFlowClassifierL4SwitchTCPDstPortThis object indicate the destination TCP port number in the
configured L4 TCP-session rule entries must be checked or not.
If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4),
then this object must be un-used(3).rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.3.1.8 |
swL2ACLQosFlowClassifierL4SwitchTCPSrcPortThis object indicate the source TCP port number in the
configured L4 TCP-session rule entries must be checked or not.
If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4),
then this object must be un-used(3).rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.3.1.9 |
swL2ACLQosFlowClassifierL4SwitchTCPFlagsThis object indicate the TCP flags in the configured L4 TCP-
session rule entries must be checked or not. If the
swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then
this object must be un-used(3).rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.3.1.10 |
swL2ACLQosFlowClassifierL4SwitchUDPDstIpThis object indicate the destination ipaddress in the configured
L4 UDP-session rule entries must be checked or not. If the
swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then
this object must be un-used(3).rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.3.1.11 |
swL2ACLQosFlowClassifierL4SwitchUDPSrcIpThis object indicate the source ipaddress in the configured L4
UDP-session rule entries must be checked or not. If the
swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then
this object must be un-used(3).rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.3.1.12 |
swL2ACLQosFlowClassifierL4SwitchUDPTosThis object indicate the type of service in the configured L4
UDP-session rule entries must be checked or not. If the
swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then
this object must be un-used(3).rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.3.1.13 |
swL2ACLQosFlowClassifierL4SwitchUDPDstPortThis object indicate the destination UDP port number in the
configured L4 UDP session rule entries must be checked or not.
If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4),
then this object must be un-used(3).rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.3.1.14 |
swL2ACLQosFlowClassifierL4SwitchUDPSrcPortThis object indicate the source UDP port number in the
configured L4 UDP session rule entries must be checked or not.
If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4),
then this object must be un-used(3).rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.3.1.15 |
swL2ACLQosFlowClassifierL4SwitchOtherDstIpThis object indicate the destination ipaddress in the configured
L4 OTHER-session rule entries must be checked or not. If the
swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then
this object must be un-used(3).rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.3.1.16 |
swL2ACLQosFlowClassifierL4SwitchOtherSrcIpThis object indicate the source ipaddress in the configured L4
OTHER-session rule entries must be checked or not. If the
swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then
this object must be un-used(3).rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.3.1.17 |
swL2ACLQosFlowClassifierL4SwitchOtherTosThis object indicate the type of service in the configured L4
OTHER-session rule entries must be checked or not. If the
swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then
this object must be un-used(3).rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.3.1.18 |
swL2ACLQosFlowClassifierL4SwitchOtherL4ProtocolThis object indicate the l4_protocol in the configured L4
OTHER-session rule entries must be checked or not. If the
swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then
this object must be un-used(3).rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.3.1.19 |
swL2ACLQosFlowClassifierL4SwitchOtherICMPMessageThis object indicate the ICMP message in the configured L4
OTHER-session rule entries must be checked or not. If the
swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then
this object must be un-used(3).rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.3.1.20 |
swL2ACLQosFlowClassifierL4SwitchOtherIGMPTypeThis object indicate the IGMP type in the configured L4
OTHER-session rule entries must be checked or not. If the
swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then
this object must be un-used(3).rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.3.1.21 |
swL2ACLQosFlowClassifierActiveRuleNumberThis object indicates the number of active rule.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.16.3.1.22 |
swL2ACLQosFlowClassifierSecurityDstMaskThis object indicates a destination IP subnet rule for the switch.
If the swL2ACLQosFlowClassifierCurrentMode is not security(2),
then this object must be 0.0.0.0.rw IpAddress .1.3.6.1.4.1.2272.1.201.1.2.16.3.1.23 |
swL2ACLQosFlowClassifierVlanTableThis table specifys which vlan has been binded in the template. SEQUENCE OF SwL2ACLQosFlowClassifierVlanEntry .1.3.6.1.4.1.2272.1.201.1.2.16.4 |
swL2ACLQosFlowClassifierVlanEntryA list of information which vlan has been binded in the template. SwL2ACLQosFlowClassifierVlanEntry .1.3.6.1.4.1.2272.1.201.1.2.16.4.1 |
swL2ACLQosFlowClassifierVlanTemplateIdThe index of template ID.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.16.4.1.1 |
swL2ACLQosFlowClassifierVlanVlanNameThe existence of VLAN name.ro DisplayString .1.3.6.1.4.1.2272.1.201.1.2.16.4.1.2 |
swL2ACLQosFlowClassifierVlanStateThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions
under which it will remain so are different from each of
the following values.
attached(2) - this entry is reside in the table.
detached(3) - writing this value to the object, and then the
corresponding entry will be removed from the table.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.4.1.3 |
swL2ACLQosTemplateRuleTableThis table specifys the template-depend rules. SEQUENCE OF SwL2ACLQosTemplateRuleEntry .1.3.6.1.4.1.2272.1.201.1.2.16.5 |
swL2ACLQosTemplateRuleEntryA list of information specifies the template-depend rules. SwL2ACLQosTemplateRuleEntry .1.3.6.1.4.1.2272.1.201.1.2.16.5.1 |
swL2ACLQosTemplateRuleTemplateIdThe index of template ID.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.1 |
swL2ACLQosTemplateRuleIndexThe index of template rule.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.2 |
swL2ACLQosTemplateRuleModeThis object indicates the rule type of the entry.ro Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.3 |
swL2ACLQosTemplateRuleSecuritySrcIpThis object indicates the source IP of flow template. If the
swL2ACLQosTemplateRuleMode is not security(2), then this object
will be display 0.0.0.0.rw IpAddress .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.4 |
swL2ACLQosTemplateRuleQosFlavorThis object indicates the rule type of the QOS mode. If the
swL2ACLQosTemplateRuleMode is not qos(3), then this object
must be flavor-un-used(6).ro Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.5 |
swL2ACLQosTemplateRuleQosValueThis object must match with swL2ACLQosTemplateRuleQosFlavor.
If the type is flavor-8021p(1), the range of this object is 0~7.
If the type is flavor-dscp(2), the range of this object is 0~63.
If the type is flavor-tcp(4) or flavor-udp(5), the range of this
object is 1~65535. If the swL2ACLQosTemplateRuleMode is not
qos(3), then this object must be NULL.rw OCTET STRING .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.6 |
swL2ACLQosTemplateRuleQosPriorityThis object indicates the priority of ingress packets in QOS mode.
If the swL2ACLQosTemplateRuleMode is not qos(3), then this
object must be 0.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.7 |
swL2ACLQosTemplateRuleQosDscpThis object indicates the Dscp of ingress packets in QOS mode.
If the swL2ACLQosTemplateRuleMode is not qos(3), then this
object must be 0.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.8 |
swL2ACLQosTemplateRuleL4SwitchSessionTypeThis object indicates the rule type of the TCP-Session in
L4-Switch mode. If the swL2ACLQosTemplateRuleMode is not
l4-switch(4), then this object must be un-used(4).rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.9 |
swL2ACLQosTemplateRuleL4SwitchSessionTCPDstIpThis object indicates the destination ipaddress in the configured
L4 TCP-session rule entries. If the swL2ACLQosTemplateRuleMode
is not l4-switch(4), then this object must be 0.0.0.0.rw IpAddress .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.10 |
swL2ACLQosTemplateRuleL4SwitchSessionTCPSrcIpThis object indicates the source ipaddress in the configured
L4 TCP-session rule entries. If the swL2ACLQosTemplateRuleMode
is not l4-switch(4), then this object must be 0.0.0.0.rw IpAddress .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.11 |
swL2ACLQosTemplateRuleL4SwitchSessionTCPTosThis object indicates the type of service in the configured
L4 TCP-session rule entries. If the swL2ACLQosTemplateRuleMode
is not l4-switch(4), then this object must be zero.rw OCTET STRING .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.12 |
swL2ACLQosTemplateRuleL4SwitchSessionTCPDstPortThis object indicates the destination TCP port number in the
configured L4 TCP-session rule entries. If the swL2ACLQosTemplateRuleMode
is not l4-switch(4), then this object must be 0.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.13 |
swL2ACLQosTemplateRuleL4SwitchSessionTCPSrcPortThis object indicates the source TCP port number in the configured
L4 TCP-session rule entries. If the swL2ACLQosTemplateRuleMode
is not l4-switch(4), then this object must be 0.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.14 |
swL2ACLQosTemplateRuleL4SwitchSessionTCPFlagsThis object indicates the TCP flags in the configured L4 TCP-
session rule entries. If the swL2ACLQosTemplateRuleMode is not
l4-switch(4), then this object must be un-used(7).
This object is deprecated because it just can let user to
choose one of these items.rwdeprecated Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.15 |
swL2ACLQosTemplateRuleL4SwitchSessionUDPDstIpThis object indicates the destination ipaddress in the configured
L4 UDP-session rule entries. If the swL2ACLQosTemplateRuleMode
is not l4-switch(4), then this object must be 0.0.0.0.rw IpAddress .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.16 |
swL2ACLQosTemplateRuleL4SwitchSessionUDPSrcIpThis object indicates the soruce ipaddress in the configured
L4 UDP-session rule entries. If the swL2ACLQosTemplateRuleMode
is not l4-switch(4), then this object must be 0.0.0.0.rw IpAddress .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.17 |
swL2ACLQosTemplateRuleL4SwitchSessionUDPTosThis object indicates the type of service in the configured
L4 UDP-session rule entries. If the swL2ACLQosTemplateRuleMode
is not l4-switch(4), then this object must be zero.rw OCTET STRING .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.18 |
swL2ACLQosTemplateRuleL4SwitchSessionUDPDstPortThis object indicates the destination UDP port number in the
configured L4 UDP-session rule entries. If the
swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object
must be 0.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.19 |
swL2ACLQosTemplateRuleL4SwitchSessionUDPSrcPortThis object indicates the source UDP port number in the configured
L4 UDP-session rule entries. If the swL2ACLQosTemplateRuleMode
is not l4-switch(4), then this object must be 0.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.20 |
swL2ACLQosTemplateRuleL4SwitchSessionOtherDstIpThis object indicates the destination ipaddress in the configured
L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode
is not l4-switch(4), then this object must be 0.0.0.0.rw IpAddress .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.21 |
swL2ACLQosTemplateRuleL4SwitchSessionOtherSrcIpThis object indicates the source ipaddress in the configured
L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode
is not l4-switch(4), then this object must be 0.0.0.0.rw IpAddress .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.22 |
swL2ACLQosTemplateRuleL4SwitchSessionOtherTosThis object indicates the type of service in the configured
L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode
is not l4-switch(4), then this object must be zero.rw OCTET STRING .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.23 |
swL2ACLQosTemplateRuleL4SwitchSessionOtherL4ProtocolThis object indicates the l4_protocol in the configured
L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode
is not l4-switch(4), then this object must be un-used(3).rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.24 |
swL2ACLQosTemplateRuleL4SwitchSessionOtherICMPTypeThis object indicates the type of ICMP message in the configured
L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode
is not l4-switch(4), then this object must be zero.rw OCTET STRING .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.25 |
swL2ACLQosTemplateRuleL4SwitchSessionOtherICMPCodeThis object indicates the code of ICMP message in the configured
L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode
is not l4-switch(4), then this object must be zero.rw OCTET STRING .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.26 |
swL2ACLQosTemplateRuleL4SwitchSessionOtherIGMPTypeThis object indicates the IGMP type in the configured
L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode
is not l4-switch(4), then this object must be un-used(5). If the
object be set to response-version-all(4), it means to create two
entries with response-version-1(2) and response-version-2(3).rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.27 |
swL2ACLQosTemplateRuleL4SwitchActionTypeThis object indicates the action when a packet matches an entry
of l4_switch mode. If the swL2ACLQosTemplateRuleMode is not
l4-switch(4), then this object must be un-used(4).rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.28 |
swL2ACLQosTemplateRuleL4SwitchActionForwardPriorityStateThis object decide to sending the packet to one of 8 hardware
priority queues or not.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.29 |
swL2ACLQosTemplateRuleL4SwitchActionForwardPriorityThis object indicates the priority related to one of 8 hardware
priority queues. If the swL2ACLQosTemplateRuleMode is not
l4-switch(4) or the
swL2ACLQosTemplateRuleL4SwitchActionForwardPriorityState is not
true(2), this object must be 0.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.30 |
swL2ACLQosTemplateRuleL4SwitchActionForwardDscpIf the swL2ACLQosTemplateRuleMode is not l4-switch(4) or the
swL2ACLQosTemplateRuleL4SwitchActionForwardPriorityState is not
true(2),, this object must be 0.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.31 |
swL2ACLQosTemplateRuleL4SwitchActionRedirectIpThis object indicates the redirected IP address that when a
packet matches an entry of l4_switch mode. If the
swL2ACLQosTemplateRuleL4SwitchActionType is not redirect(3),
this object must be 0.0.0.0.rw IpAddress .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.32 |
swL2ACLQosTemplateRuleL4SwitchActionRedirectDropUnreachableThis object indicates the action of this entry.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
false(2) - routing unreachable packet by using L2/IPv4 router
forwarding table.
true(3) - dropping unreachable packetrw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.33 |
swL2ACLQosTemplateRuleStateThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions
under which it will remain so are different from each of
the following values.
invalid(2) - writing this value to the object, and then the
corresponding entry will be removed from the table.
valid(3) - this entry is reside in the table.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.34 |
swL2ACLQosTemplateRuleL4SwitchSessionTCPFlagsAllThis object indicates the TCP flags in the configured L4 TCP-
session rule entries. If the swL2ACLQosTemplateRuleMode is not
l4-switch(4), then this object must be zero.rw Bits .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.35 |
swL2ACLQosTemplateRuleSecurityDstIpThis object indicates the destination IP of flow template. If
the swL2ACLQosTemplateRuleMode is not security(2), then this
object will be display 0.0.0.0.rw IpAddress .1.3.6.1.4.1.2272.1.201.1.2.16.5.1.36 |
swL2ACLQosDestinationIpFilterTableThis table defines information for the device to filter packets
with specific Destination IP address. The IP address can be a
unicast address or multicast address. This table has higher
priority than both static FDB table and IGMP table. It means
that if a IP address appears on this table also appears on the
static FDB table, the device will use the information provide by
this table to process the packet. SEQUENCE OF SwL2ACLQosDestinationIpFilterEntry .1.3.6.1.4.1.2272.1.201.1.2.16.6 |
swL2ACLQosDestinationIpFilterEntryA list of information about a specific unicast/multicast IP
address for which the switch has filtering information. SwL2ACLQosDestinationIpFilterEntry .1.3.6.1.4.1.2272.1.201.1.2.16.6.1 |
swL2ACLQosDestinationIpFilterIndexThe index of this rule.roobsolete INTEGER .1.3.6.1.4.1.2272.1.201.1.2.16.6.1.1 |
swL2ACLQosDestinationIpFilterIpAddrThis object indicates a unicast IP address for which the
switch has filtering information.ro IpAddress .1.3.6.1.4.1.2272.1.201.1.2.16.6.1.2 |
swL2ACLQosDestinationIpFilterStateThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions
under which it will remain so are different from each of
the following values.
invalid(2) - writing this value to the object, and then the
corresponding entry will be removed from the table.
valid(3) - this entry is reside in the table.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.6.1.3 |
swL2ACLQosFDBFilterTableThis table defines information for the device to filter packets
with specific MAC address (either as the DA and/or as the SA).
The MAC address can be a unicast address or a multicast address.
This table has higher priority than both static FDB table and
IGMP table. It means that if a MAC address appears on this table
also appears on the static FDB table, the device will use the
information provide by this table to process the packet. SEQUENCE OF SwL2ACLQosFDBFilterEntry .1.3.6.1.4.1.2272.1.201.1.2.16.7 |
swL2ACLQosFDBFilterEntryA list of information about a specific unicast/multicast MAC
address for which the switch has filtering information. SwL2ACLQosFDBFilterEntry .1.3.6.1.4.1.2272.1.201.1.2.16.7.1 |
swL2ACLQosFDBFilterIndexThe index of this rule.roobsolete INTEGER .1.3.6.1.4.1.2272.1.201.1.2.16.7.1.1 |
swL2ACLQosFDBFilterVlanNameThe existence of VALN name.ro DisplayString .1.3.6.1.4.1.2272.1.201.1.2.16.7.1.2 |
swL2ACLQosFDBFilterMacAddressThis object will filter on destination MAC address operates on
bridged packets, but not on routed packets. And It will filter
on source MAC operates on all packets.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.2272.1.201.1.2.16.7.1.3 |
swL2ACLQosFDBFilterStateThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions
under which it will remain so are different from each of
the following values.
invalid(2) - writing this value to the object, and then the
corresponding entry will be removed from the table.
valid(3) - this entry is reside in the table.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.7.1.4 |
swL2ACLQosIpFragmentFilterDropPktsThis object decide to drop fragmented IP packets or not.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.8 |
swL2ACLQosSchedulingTableThe switch contains 4 hardware priority queues. Incoming packets
must be mapped to one of these four queues. Each hardware queue
will transmit all of the packets in its buffer before allowing
the next lower priority queue to transmit its packets. When the
lowest hardware priority queue has finished transmitting all of
its packets, the highest hardware priority queue can again
transmit any packets it may have received. SEQUENCE OF SwL2ACLQosSchedulingEntry .1.3.6.1.4.1.2272.1.201.1.2.16.9 |
swL2ACLQosSchedulingEntryA list of information specifies the Qos output scheduling Table. SwL2ACLQosSchedulingEntry .1.3.6.1.4.1.2272.1.201.1.2.16.9.1 |
swL2ACLQosSchedulingPortIndexThe index of logical port.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.16.9.1.1 |
swL2ACLQosSchedulingClassIdThis specifies which of the four hardware priority queues. The
four hardware priority queues are identified by number, from 0
to 3, with the 0 queue being the lowest priority.ro INTEGER .1.3.6.1.4.1.2272.1.201.1.2.16.9.1.2 |
swL2ACLQosSchedulingWRRValueSpecifies the weighted round robin (WRR) the above specified
hardware priority queue will be allowed to transmit before
allowing the next lowest priority queue to transmit its packets.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.16.9.1.3 |
swL2ACLQosMacPriorityTableThis table indicates the destination mac priority in flow
classifier. SEQUENCE OF SwL2ACLQosMacPriorityEntry .1.3.6.1.4.1.2272.1.201.1.2.16.10 |
swL2ACLQosMacPriorityEntryA list of information specifies the destination mac priority in
flow classifier. SwL2ACLQosMacPriorityEntry .1.3.6.1.4.1.2272.1.201.1.2.16.10.1 |
swL2ACLQosMacPriorityIndexThe index of this rule.roobsolete INTEGER .1.3.6.1.4.1.2272.1.201.1.2.16.10.1.1 |
swL2ACLQosMacPriorityVlanNameThe existence VLAN name.ro DisplayString .1.3.6.1.4.1.2272.1.201.1.2.16.10.1.2 |
swL2ACLQosMacPriorityDstMacAddressThis object will filter on destination MAC address operates on
bridged packets, but not on routed packets. And It will filter
on source MAC operates on all packets.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.2272.1.201.1.2.16.10.1.3 |
swL2ACLQosMacPriorityPriorityValueThis object indicates the priority related to one of 8 hardware
priority queues.rw INTEGER .1.3.6.1.4.1.2272.1.201.1.2.16.10.1.4 |
swL2ACLQosMacPriorityStateThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions
under which it will remain so are different from each of
the following values.
invalid(2) - writing this value to the object, and then the
corresponding entry will be removed from the table.
valid(3) - this entry is reside in the table.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.16.10.1.5 |
swL2MgmtPortMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.2272.1.201.1.2.17 |
swL2MgmtPortCurrentLinkStatusThis object indicates the current management port link status.ro Enumeration .1.3.6.1.4.1.2272.1.201.1.2.17.1 |
swL2MgmtPortCurrentNwayStatusThis object indicates the current management port speed and
duplex mode.ro Enumeration .1.3.6.1.4.1.2272.1.201.1.2.17.2 |
swL2MgmtPortAdminStateThis object decide the management port enabled or disabled.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.17.3 |
swL2MgmtPortNwayStateChose the management port speed, duplex mode, and N-Way
function mode.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.17.4 |
swL2MgmtPortFlowCtrlStateThe flow control mechanism is different between full duplex
mode and half duplex mode. For half duplex mode, the jamming
signal is asserted. For full duplex mode, IEEE 802.3x flow
control function sends PAUSE frames and receives PAUSE frames.rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.17.5 |
swL2MgmtPortLinkUpDownTrapEnableIndicates whether linkUp/linkDown traps should be generated for
the management port. By default, this object should have the
value enabled(3).rw Enumeration .1.3.6.1.4.1.2272.1.201.1.2.17.6 |