SA-RG-MIB
AI MIB Summary
The SA-RG-MIB module manages router and wireless interface parameters within SA (likely Samsung or a specific OEM) residential gateway firmware, enabling configuration of SSID settings, radio power levels, and WAN/LAN routing states via SNMP or embedded CM configuration files.
Controls the behavior of router/wireless functions. Can be part of CM configuration file.
Main OID:
saRg.1.3.6.1.4.1.1429.79.2
241
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
241 total| Object Name |
|---|
sa OBJECT IDENTIFIER .1.3.6.1.4.1.1429 |
saModules OBJECT IDENTIFIER .1.3.6.1.4.1.1429.79 |
saRgControls the behavior of router/wireless functions. Can be part of CM configuration file. MODULE-IDENTITY .1.3.6.1.4.1.1429.79.2 |
saRgDevice OBJECT IDENTIFIER .1.3.6.1.4.1.1429.79.2.1 |
saRgDeviceBase OBJECT IDENTIFIER .1.3.6.1.4.1.1429.79.2.1.1 |
saRgDeviceModeDefines the mode of operation for the device. This parameter is stored in non-vol and is multiSsid(1) by default. Setting this object via SNMP will cause the unit to reboot. This MIB will be superseded in the config file by TLV202. This MIB will read the proper value if set from TLV202. This MIB will be superseded by saRgIpMgmtLanMode inbridge(1) or mixed(4). disable(0): Value will reflect when TLV202 is set to 0. Not all platforms have this value implemented. multiSsid(1): Default Value. Value supports IPv4RG with multiple SSID configuration and bridge mode via saRgIpMgmtLanMode MIB. Bridge mode is the same as eRouter disabled mode. IPV4RG is the non eRouter behavior that existed before in our router products. Ipv4(3): eRouter IPv4 only mode Ipv6(4): eRouter IPv6 only mode Dualstack(5): eRouter IPv4 and IPv6 dualstack Note: cableHome11(2) support is not available.rw Enumeration .1.3.6.1.4.1.1429.79.2.1.1.1 |
saRgDeviceResetDefaultEnableThis object controls the reset to factory default functionality of the gateway. This prevents the local user from using the reset switch to gain access to the setup pages using the default user name and password. The objective is to prevent theft of service from a user who reconfigures the device to add users or change wireless settings. Enable (object set to true): 1. Momentary press of the Reset Switch (<5 seconds) DOCSIS restart of the modem (reboot, no reset to factory default values). 2. Pressing the reset switch for >5 seconds Reboots and resets of all values (modem and router) to factory default. Disable (object set to false): 1. Momentary press of the Reset Switch (<5 seconds) DOCSIS restart of the modem (reboot, no reset to factory default values). 2. Pressing the reset switch for >5 seconds Modem reboots and resets only the cable modem settings to factory default values. The router settings should remain and should not NOT reset to factory default.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.1.1.2 |
saRgDeviceRemoteWebAccessPortDefines what port to use for the WAN IP address of the gateway to be able to access RG web pages. This value is to be stored in non-vol and will persist across reboots. Only a factory reset would clear itrw InetPortNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.1429.79.2.1.1.4 |
saRgDeviceLanLanIsolationThis MIB is only available in D3.0 products. This MIB does not take effect if the modem is in VLAN mode i.e if saRgIpMgmtLanMode.32=vlan(5). Lan-Lan Isolation allows you block IP access between CPEs connected to the Ethernet ports. Use this mib in conjunction with saRgDeviceLanWlanIsolation and saRgDot11BssApIsolation.x for complete isolation between CPEs connected to the RG. This MIB is written to non-vol and set to disable(0) after a factory reset. disable(0)- No Isolation enable(1)- Enable Isolation featurerw Enumeration .1.3.6.1.4.1.1429.79.2.1.1.6 |
saRgDeviceLanWlanIsolationThis MIB is only available in D3.0 products. This MIB does not take effect if the modem is in VLAN mode i.e if saRgIpMgmtLanMode.32=vlan(5). Lan-Wlan Isolation allows you block IP access between CPEs connected to the Ethernet port and Wireless SSIDs. Use this mib in conjunction with saRgDeviceLanLanIsolation and saRgDot11BssApIsolation.x for complete isolation between CPEs connected to the RG. This MIB is written to non-vol and set to disable(0) after a factory reset. disable(0)- No Isolation enable(1)- Enable Isolation featurerw Enumeration .1.3.6.1.4.1.1429.79.2.1.1.7 |
saRgDeviceIpv6TransThis MIB will control which IPv6 transition technology is enabled on the device. After setting this MIB to disable in the config file, IPv4 traffic will pass normally through the device. When switched to dslite, the DSLite feature will be enabled. If eRouter is in IPv6-only mode, DS Lite will tunnel IPv4 traffic over IPv6 to the AFTR address specified either manually or in the DHCPv6 option-64. See saRgDslite MIB tree for more details. If this setting is changed by the config file, the CM will reboot. This MIB is written to non-vol and set to disable(0) after a factory reset. disable(0) - No technology is enabled enable(1) - DS lite feature is enabledro Enumeration .1.3.6.1.4.1.1429.79.2.1.1.8 |
saRgDeviceIpv6PassthroughThis MIB controls IPv6 passthrough on the RG and is applicable in bridge and router modes. When disabled the RG will function without any IPv6 passthrough When IPv6 passthrough is enabled in Bridge Mode the RG will drop all IPv4 traffic When IPv6 passthrough is enabled in router mode the RG will operate as normal for IPv4 traffic, but all IPv6 traffic will passthrough This MIB requires CM reboot. This MIB is written to non-vol and set to disable(0) after a factory reset.rw Enumeration .1.3.6.1.4.1.1429.79.2.1.1.9 |
saRgDeviceFactoryResetSet routerAndWifi(1) to restore default settings of both the router and wifi. Set routerOnly(2) to restore default settings of the router. Set wifi(3) to restore default settings of the wifi. Return false(0) when read.rw Enumeration .1.3.6.1.4.1.1429.79.2.1.1.1002 |
saRgDeviceTimeSetup OBJECT IDENTIFIER .1.3.6.1.4.1.1429.79.2.1.5 |
saRgDeviceTimeSetupNtpEnabledStored in non-vol, disabled after factory reset.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.1.5.1 |
saRgDeviceTimeSetupNtpServerTableUp to 3 NTP servers are supported. This table is stored in non-vol. Default entries after factory reset are: 1: time.nist.gov 2: nist.aol-ca.truetime.com 3: nist1-ny.glassey.com SEQUENCE OF SaRgDeviceTimeSetupNtpServerEntry .1.3.6.1.4.1.1429.79.2.1.5.2 |
saRgDeviceTimeSetupNtpServerEntry SaRgDeviceTimeSetupNtpServerEntry .1.3.6.1.4.1.1429.79.2.1.5.2.1 |
saRgDeviceTimeSetupNtpServerIndexThe index INTEGER .1.3.6.1.4.1.1429.79.2.1.5.2.1.1 |
saRgDeviceTimeSetupNtpServerAddressIP address or FQDN of the NTP server.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.1429.79.2.1.5.2.1.2 |
saRgDeviceTimeSetupZoneTime zone for the gateway. Stored in non-vol, gmtZeroDublinEdinburghLisbonLondon(26) after factory reset.rw SaRgTimeZone .1.3.6.1.4.1.1429.79.2.1.5.3 |
saRgDeviceTimeSetupDstDaylight saving time. If set to 0, DST is disabled Stored in non-vol, 0 after factory reset.rw INTEGER .1.3.6.1.4.1.1429.79.2.1.5.4 |
saRgDeviceIanaContent OBJECT IDENTIFIER .1.3.6.1.4.1.1429.79.2.1.7 |
saRgDeviceIanaIAIDReturns the IAID value embedded in the IA_NA for the eRouter's DHCPv6 lease.ro Unsigned32 .1.3.6.1.4.1.1429.79.2.1.7.1 |
saRgDeviceIanaT1Returns the T1 value embedded in the IA_NA for the eRouter's DHCPv6 lease.ro Integer32 .1.3.6.1.4.1.1429.79.2.1.7.2 |
saRgDeviceIanaT2Returns the T2 value embedded in the IA_NA for the eRouter's DHCPv6 lease.ro Integer32 .1.3.6.1.4.1.1429.79.2.1.7.3 |
saRgDeviceIanaTableTable of IA Address entries associated with IA_NA for the eRouter's DHCPv6 lease. SEQUENCE OF SaRgDeviceIanaEntry .1.3.6.1.4.1.1429.79.2.1.7.4 |
saRgDeviceIanaEntryTable of IA Address entries associated with IA_NA for the eRouter's DHCPv6 lease. SaRgDeviceIanaEntry .1.3.6.1.4.1.1429.79.2.1.7.4.1 |
saRgDeviceIanaIndexThe index INTEGER .1.3.6.1.4.1.1429.79.2.1.7.4.1.1 |
saRgDeviceIanaValueIPv6 address provided to the eRouter WAN interface via DHCPv6.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.1429.79.2.1.7.4.1.2 |
saRgDeviceIanaPreferredLifetimePreferred Lifetime setting for an IPv6 address assigned to the eRouter.ro Integer32 .1.3.6.1.4.1.1429.79.2.1.7.4.1.3 |
saRgDeviceIanaValidLifetimeValid Lifetime setting for an IPv6 address assigned to the eRouter.ro Integer32 .1.3.6.1.4.1.1429.79.2.1.7.4.1.4 |
saRgDeviceIapdContent OBJECT IDENTIFIER .1.3.6.1.4.1.1429.79.2.1.8 |
saRgDeviceIapdIAIDReturns the IAID value embedded in the IA_PD for the eRouter's DHCPv6 lease.ro Unsigned32 .1.3.6.1.4.1.1429.79.2.1.8.1 |
saRgDeviceIapdT1Returns the T1 value embedded in the IA_PD for the eRouter's DHCPv6 lease.ro Integer32 .1.3.6.1.4.1.1429.79.2.1.8.2 |
saRgDeviceIapdT2Returns the T2 value embedded in the IA_PD for the eRouter's DHCPv6 lease.ro Integer32 .1.3.6.1.4.1.1429.79.2.1.8.3 |
saRgDeviceIapdTableTable of IA Prefix entries associated with IA_PD for the eRouter's DHCPv6 lease. SEQUENCE OF SaRgDeviceIapdEntry .1.3.6.1.4.1.1429.79.2.1.8.4 |
saRgDeviceIapdEntryTable of IA Address entries associated with IA_PD for the eRouter's DHCPv6 lease. SaRgDeviceIapdEntry .1.3.6.1.4.1.1429.79.2.1.8.4.1 |
saRgDeviceIapdIndexThe index INTEGER .1.3.6.1.4.1.1429.79.2.1.8.4.1.1 |
saRgDeviceIapdPreferredLifetimePreferred Lifetime setting for an IPv6 address assigned to the eRouter.ro Integer32 .1.3.6.1.4.1.1429.79.2.1.8.4.1.2 |
saRgDeviceIapdValidLifetimeValid Lifetime setting for an IPv6 address assigned to the eRouter.ro Integer32 .1.3.6.1.4.1.1429.79.2.1.8.4.1.3 |
saRgDeviceIapdPrefixLengthLength (in bits) for this prefix.ro INTEGER .1.3.6.1.4.1.1429.79.2.1.8.4.1.4 |
saRgDeviceIapdPrefixValuePrefix address specified in the IA_PD.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.1429.79.2.1.8.4.1.5 |
saRgDot11 OBJECT IDENTIFIER .1.3.6.1.4.1.1429.79.2.2 |
saRgDot11MgmtBase OBJECT IDENTIFIER .1.3.6.1.4.1.1429.79.2.2.1 |
saRgDot11OnOffPushButtonTimeSpecifies how long to press WPS button to enable or disable the WiFi interface (primary SSID). When set to 11, the feature is disabled. Stored in non-vol, 11 after factory reset.rw INTEGER .1.3.6.1.4.1.1429.79.2.2.1.20 |
saRgDot11Bss OBJECT IDENTIFIER .1.3.6.1.4.1.1429.79.2.2.2 |
saRgDot11BssTableBSS table SEQUENCE OF SaRgDot11BssEntry .1.3.6.1.4.1.1429.79.2.2.2.1 |
saRgDot11BssEntryA row in the table which represents parameters for SSID. SaRgDot11BssEntry .1.3.6.1.4.1.1429.79.2.2.2.1.1 |
saRgDot11BssIdReturns the BSSIDro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.2.2.1.1.1 |
saRgDot11BssEnableControls the BSS state. When set to enableOnline(3), the SSID is enabled only when the cable modem is online. When the modem changes state to offline, the AP will send dissasociation messages to the STAs connected to the SSID and then disable. The value of primary BSS is stored in non-vol and is enabled(1) after factory reset. The other BSSs are disabled by default. If other BSS's SSID name is not defined, the BSS will not be enabled.rw Enumeration .1.3.6.1.4.1.1429.79.2.2.2.1.1.2 |
saRgDot11BssSsidControls and reflects the service set identifier. The value of primary BSS is stored in non-vol and is empty after factory reset. If other BSS's SSID name is not defined, the BSS will not be enabled.rw OCTET STRING .1.3.6.1.4.1.1429.79.2.2.2.1.1.3 |
saRgDot11BssSecurityModeSecrity for BSS. Beacause WPA2 is backwords compatible with WPA, setting this object to wpaWpa2Psk(7) is allowed and has the same effect as setting to wpa2Psk(3). The same is true for wpaWpa2Enterprise(8) and wpa2Enterprise(5). The value for primary BSS is stored in non-vol and is wpaWpa2Psk(7) after factory reset. For each other BSS security has to be included in configuration file or the BSS will be disabled.rw Enumeration .1.3.6.1.4.1.1429.79.2.2.2.1.1.4 |
saRgDot11BssClosedNetworkControls whether the device will operate in closed network mode. If set to true(1), then the network mode is closed and the SSID will not be broadcast in beacon packets. If set to false(2), then the network mode is open and the SSID will be broadcast in beacon packets. The value for primary BSS is stored in non-vol. The default value for other BSSs is false.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.2.2.1.1.5 |
saRgDot11BssAccessModeControls what stations will be given access to the device. If set to allowAny(0), then any station will be allowed to connect. If set to allowList(1), then only stations whose MAC address appears in the saRgDot11AccessMacTable will be allowed to connect. The value for primary BSS is stored in non-vol. The default value for other BSSs is 0.rw Enumeration .1.3.6.1.4.1.1429.79.2.2.2.1.1.6 |
saRgDot11BssMaxNumStaThis object defines the maximum number of STAs that can connect to this SSID. Note that the maximum number of STA accross all SSIDs in the AP is 128. Default value is 128 for all SSIDs. The value for primary BSS is stored in non-vol.rw INTEGER .1.3.6.1.4.1.1429.79.2.2.2.1.1.11 |
saRgDot11BssUserStatusProvides the BSS Id Web UI or Wireless ON/OFF (if exist) status that is set by the user. If the user can press the Wireless ON/OFF (if exist) button and its status can be seen in BSS ID Web UI. If user changes access point status in Web UI, it will reflect the status of Wireless ON/OFF LED.ro Enumeration .1.3.6.1.4.1.1429.79.2.2.2.1.1.13 |
saRgDot11BssApIsolationThis MIB is only available in D3.0 products. AP Isolation (Access Point Isolation) allows you to isloate traffic between CPEs on the same Wifi SSID. This allows a measure of security to prevent hackers from accessing other CPEs in a public Wifi environment. Ex. When this MIB is enabled you can not ping between CPEs connected to the same SSID. AP Isolation is settable per SSID in either VLAN or non VLAN modes. This MIB is written to non-vol and set to disable(0) after a factory reset. disable(0)- No AP Isolation enable(1)- Enable AP Isolation feature.rw Enumeration .1.3.6.1.4.1.1429.79.2.2.2.1.1.15 |
saRgDot11BssSecSsidTrafficPriorityThis MIB is only available in D3.0 products and applicable for secondary SSID in hotspot environment. When disabled, all the traffic to the secondary SSID in question would have same WMM QoS parameters as the primary SSID. When set to ac_bk(1), the secondary SSID traffic would be classified as AC_BK resulting in better DS prioritization for primary SSID trafficro Enumeration .1.3.6.1.4.1.1429.79.2.2.2.1.1.16 |
saRgDot11BssRejectPriSsidStaThis MIB is only available in D3.0 products and applicable for secondary SSID in hotspot environment. By default, a private SSID STA can associate to hotspot SSID. This MIB can be used to reject private SSID STAs to associate with hotspot SSID if and only if STA has associated with private SSID once before.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.2.2.1.1.17 |
saRgDot11BssPrimary OBJECT IDENTIFIER .1.3.6.1.4.1.1429.79.2.2.2.3 |
saRgDot11BssPrimarySsidTypeThis object specifies the type of SSID used. mac6char(1): If saRgDot11BssSsid.32 is empty, the SSID is the last 3 bytes of DOCSIS MAC address, displayed as 6 lowercase hex characters. If saRgDot11BssSsid.32 is not empty, SSID is the value from saRgDot11BssSsid.32 (set by SNMP or the user). mac6char-prefix(2): the same as mac6char(2) with the prefix addition defined in saRgDot11BssPrimarySsidPrefix. If saRgDot11BssSsid.32 is not empty, this prefix does not show. mac4char-prefix(3): the same as mac6char-prefix(2) but 4 MAC characters instead of 6. prefix-force(4): The prefix is always included, even if saRgDot11BssSsid.32 is empty. Note: stored in non-vol. mac6char(1) after factory resetrw Enumeration .1.3.6.1.4.1.1429.79.2.2.2.3.1 |
saRgDot11BssPrimarySsidPrefixThe prefix for primary SSID, if saRgDot11BssSsid.32 is empty and saRgDot11BssPrimarySsidType is set to mac6char-prefix(2). Stored in non-vol. Empty after factory reset.rw SnmpAdminString .1.3.6.1.4.1.1429.79.2.2.2.3.2 |
saRgDot11Privacy OBJECT IDENTIFIER .1.3.6.1.4.1.1429.79.2.2.3 |
saRgDot11WpaTableWPA table SEQUENCE OF SaRgDot11WpaEntry .1.3.6.1.4.1.1429.79.2.2.3.1 |
saRgDot11WpaEntryA row in the table which represents WPA parameters for BSS. SaRgDot11WpaEntry .1.3.6.1.4.1.1429.79.2.2.3.1.1 |
saRgDot11WpaAlgorithmThe value of tkip(0) is not allowed when security is WPA2. The value for primary BSS is stored in non-vol and tkipPlusAes(2) after factory reset. The default value for other BSSs is tkip.rw Enumeration .1.3.6.1.4.1.1429.79.2.2.3.1.1.1 |
saRgDot11WpaPreSharedKeySets the WPA Pre-Shared Key (PSK). This value MUST be either a 64-digit hexadecimal number, OR a 8 to 63 character ASCII string. The value for primary BSS is stored in non-vol and is the serial number of the device after factory reset. The default value for other BSSs is 8 0's. This object return an empty string when read.rw OCTET STRING .1.3.6.1.4.1.1429.79.2.2.3.1.1.2 |
saRgDot11WpaGroupRekeyIntervalSets the WPA Group Rekey Interval in seconds. Set to zero to disable periodic rekeying. The value for primary BSS is stored in non-vol and is 3600 after factory reset. The default value for other BSSs is 3600.rw INTEGER UNITS "seconds" .1.3.6.1.4.1.1429.79.2.2.3.1.1.3 |
saRgDot11RadiusTableWPA table SEQUENCE OF SaRgDot11RadiusEntry .1.3.6.1.4.1.1429.79.2.2.3.2 |
saRgDot11RadiusEntryA row in the table which represents WPA parameters for BSS. SaRgDot11RadiusEntry .1.3.6.1.4.1.1429.79.2.2.3.2.1 |
saRgDot11RadiusAddressTypeType of RADIUS server IP address.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.1429.79.2.2.3.2.1.1 |
saRgDot11RadiusAddressSets RADIUS server IP address. The value for primary BSS is stored in non-vol and is 0.0.0.0 after factory reset. The default value for other BSSs is 0.0.0.0.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.1429.79.2.2.3.2.1.2 |
saRgDot11RadiusPortSets the UDP port used to communicate with the RADIUS server. The value for primary BSS is stored in non-vol and is 1645 after factory reset. The default value for other BSSs is 1645.rw InetPortNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.1429.79.2.2.3.2.1.3 |
saRgDot11RadiusKeySets or displays the RADIUS key. The value for primary BSS is stored in non-vol and is null after factory reset. The default value for other BSSs is null. This object return an empty string when read.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.2.3.2.1.4 |
saRgDot11RadiusReAuthIntervalSets the RADIUS Rekey Interval in seconds. Set to zero to disable periodic rekeying. The value for primary BSS is stored in non-vol and is 3600 after factory reset. The default value for other BSSs is 3600.rw INTEGER UNITS "seconds" .1.3.6.1.4.1.1429.79.2.2.3.2.1.5 |
saRgDot11WepTableWEP table SEQUENCE OF SaRgDot11WepEntry .1.3.6.1.4.1.1429.79.2.2.3.3 |
saRgDot11WepEntryA row in the table which represents WPA parameters for BSS. SaRgDot11WepEntry .1.3.6.1.4.1.1429.79.2.2.3.3.1 |
saRgDot11WepDefaultKeyControls and reflects the default key which will be used when 64 or 128 bit encryption is enabled. Indicates the entry from the saRgDot1164BitKeyTable if saRgDot11EncryptionMode is set to wep64(1), or the entry from the saRgDot11128BitKeyTable if saRgDot11EncryptionMode is set to wep128(2). The value for primary BSS is stored in non-vol and is 1 after factory reset. The default value for other BSSs is 1.rw INTEGER .1.3.6.1.4.1.1429.79.2.2.3.3.1.1 |
saRgDot11WepEncryptionModeThe value for primary BSS is stored in non-vol and is wep128(1) after factory reset. The default value for other BSSs is wep128.rw Enumeration .1.3.6.1.4.1.1429.79.2.2.3.3.1.2 |
saRgDot11WepPassPhraseControls and reflects the WEP pass phrase. The value for primary BSS is stored in non-vol and is null after factory reset. The default value for other BSSs is null. This object return an empty string when read.rw DisplayString .1.3.6.1.4.1.1429.79.2.2.3.3.1.3 |
saRgDot11Wep64BitKeyTableA table of 40 bit key values used when saRgDot11WepEncryptionMode is set to wep64(0). SEQUENCE OF SaRgDot11Wep64BitKeyEntry .1.3.6.1.4.1.1429.79.2.2.3.4 |
saRgDot11Wep64BitKeyEntryA row in the table which represents a single 64 bit key. SaRgDot11Wep64BitKeyEntry .1.3.6.1.4.1.1429.79.2.2.3.4.1 |
saRgDot11Wep64BitKeyIndexIdentifies the instance of this table row. Integer32 .1.3.6.1.4.1.1429.79.2.2.3.4.1.1 |
saRgDot11Wep64BitKeyValueA 40 bit key to be used when saRgDot11WepEncryptionMode is set to wep64(1). The value for primary BSS is stored in non-vol and is all 1's after factory reset. The default value for other BSSs is all 0's. This object return an empty string when read.rw OCTET STRING .1.3.6.1.4.1.1429.79.2.2.3.4.1.2 |
saRgDot11Wep128BitKeyTableA table of 104 bit key values used when saRgDot11WepEncryptionMode is set to wep128(1). SEQUENCE OF SaRgDot11Wep128BitKeyEntry .1.3.6.1.4.1.1429.79.2.2.3.5 |
saRgDot11Wep128BitKeyEntryA row in the table which represents a single 128 bit key. SaRgDot11Wep128BitKeyEntry .1.3.6.1.4.1.1429.79.2.2.3.5.1 |
saRgDot11Wep128BitKeyIndexIdentifies the instance of this table row. Integer32 .1.3.6.1.4.1.1429.79.2.2.3.5.1.1 |
saRgDot11Wep128BitKeyValueA 104 bit key to be used when saRgDot11WepEncryptionMode is set to wep128(2). The value for primary BSS is stored in non-vol and is all 1's. The default value for other BSSs is all 0's. This object return an empty string when read.rw OCTET STRING .1.3.6.1.4.1.1429.79.2.2.3.5.1.2 |
saRgDot11PrivacyWps OBJECT IDENTIFIER .1.3.6.1.4.1.1429.79.2.2.3.6 |
saRgDot11PrivacyWpsPushButtonTimeSpecifies how long to press WPS button to start the WPS procedure. 0 means disable WPS. Stored in non-vol, 1 after factory reset.rw INTEGER .1.3.6.1.4.1.1429.79.2.2.3.6.1 |
saRgDot11Client OBJECT IDENTIFIER .1.3.6.1.4.1.1429.79.2.2.4 |
saRgDot11ClientTableA table of wireless clients that are associated with the BSS. SEQUENCE OF SaRgDot11ClientEntry .1.3.6.1.4.1.1429.79.2.2.4.2 |
saRgDot11ClientEntryA row in the table that specifies a single station MAC address. SaRgDot11ClientEntry .1.3.6.1.4.1.1429.79.2.2.4.2.1 |
saRgDot11ClientIndexIndicates the instance of this table row. Integer32 .1.3.6.1.4.1.1429.79.2.2.4.2.1.1 |
saRgDot11ClientStationA MAC address of a client associated with the BSS.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.2.4.2.1.2 |
saRgDot11ExtMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.1429.79.2.2.6 |
saRgDot11ExtMgmtTableMultiple Radio Configuration Table SEQUENCE OF SaRgDot11ExtMgmtEntry .1.3.6.1.4.1.1429.79.2.2.6.1 |
saRgDot11ExtMgmtEntryA row in the table which represents parameters for a Radio. Index 32 should be set for Radio 0 -- 2.4 GHz if populated. Index 112 should be set for Radio 1 SaRgDot11ExtMgmtEntry .1.3.6.1.4.1.1429.79.2.2.6.1.1 |
saRgDot11ExtMbssUserControlSets the number of user controlled Wifi networks via web pages. 1: The user has control over the primary wireless network only. No guest network page is displayed. 2: The user has control over the primary wireless network and one guest network. No drop down menu (or only 1 item in the menu) for additional guest network configuration. 3: Same as above with 2 guest networks. 4: Same as above with 3 guest networks. 5: Same as above with 4 guest networks. 6: Same as above with 5 guest networks. 7: Same as above with 6 guest networks. 8: Same as above with 7 guest networks. Bit Mask Control: Bit 16: -- User has control over Primary Wireless Network : 65536 Bit 17: -- User has control over Guest Network 1 (interface 33) : 131072 Bit 18: -- User has control over Guest Network 2 (interface 34) : 262144 Bit 19: -- User has control over Guest Network 3 (interface 35) : 524288 Bit 20: -- User has control over Guest Network 4 (interface 36) :1048576 Bit 21: -- User has control over Guest Network 5 (interface 37) :2097152 Bit 22: -- User has control over Guest Network 6 (interface 38) :4194304 Bit 23: -- User has control over Guest Network 7 (interface 39) :8388608 This object value is stored in non-vol and set to 1 after factory reset.rw INTEGER (1..8|65536..16711680) .1.3.6.1.4.1.1429.79.2.2.6.1.1.15 |
saRgDot11ExtMbssUseNonvolAllows to save additional BSS parameters to non-vol if set to true. Primary BSS parameters are ALWAYS stored in non-vol. This object value is stored in non-vol and set to false after factory reset.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.2.6.1.1.16 |
saRgDot11ExtMbssAdminControlSets the number of admin controlled Wifi networks via web pages. 1: The admin has control over the primary wireless network only. No guest network page is displayed. 2: The admin has control over the primary wireless network and one guest network. No drop down menu (or only 1 item in the menu) for additional guest network configuration. 3: Same as above with 2 guest networks. 4: Same as above with 3 guest networks. 5: Same as above with 4 guest networks. 6: Same as above with 5 guest networks. 7: Same as above with 6 guest networks. 8: Same as above with 7 guest networks. Bit 16: -- Admin Has control over Primary Wireless Network : 65536 Bit 17: -- Admin Has control over Guest Network 1 (interface 33) : 131072 Bit 18: -- Admin Has control over Guest Network 2 (interface 34) : 262144 Bit 19: -- Admin Has control over Guest Network 3 (interface 35) : 524288 Bit 20: -- Admin Has control over Guest Network 4 (interface 36) :1048576 Bit 21: -- Admin Has control over Guest Network 5 (interface 37) :2097152 Bit 22: -- Admin Has control over Guest Network 6 (interface 38) :4194304 Bit 23: -- Admin Has control over Guest Network 7 (interface 39) :8388608 This object value is stored in non-vol and set to 1 after factory reset.rw INTEGER (1..8|65536..16711680) .1.3.6.1.4.1.1429.79.2.2.6.1.1.17 |
saRgDot11ExtActualChannelReports the current channel number that wireless is on. The value of 0 means wireless is disabled.ro INTEGER .1.3.6.1.4.1.1429.79.2.2.6.1.1.18 |
saRgDot11ApplySettingsIf set to true(1), then all the settings (MIB values) from this MIB tree will be applied to run time configuration, modifying previous RG operation with the new settings. Before setting the value to true, MIBs modified in the MIB tree are stored in non-vol and will not modify RG operation until saRgDot11ApplySettings is set to true or CM resets. Note: this applies only to the MIB objects that are stored in non-vol. Always returns false(2) when read.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.2.1001 |
saRgIpMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.1429.79.2.3 |
saRgIpMgmtLanTableNetworks on the LAN side. Primary BSS stored in non-vol. SEQUENCE OF SaRgIpMgmtLanEntry .1.3.6.1.4.1.1429.79.2.3.2 |
saRgIpMgmtLanEntryList of networks on the LAN side. SaRgIpMgmtLanEntry .1.3.6.1.4.1.1429.79.2.3.2.1 |
saRgIpMgmtLanModeDefines the mode of operation for the device. Setting this object via SNMP for the primary BSS will cause the unit to reboot. Setting this object via SNMP for the secondary BSSs will not cause the unit to reboot. The value for primary BSS is stored in non-vol and is router after factory reset. The default value for other BSSs is router. This MIB supersedes saRgDeviceMode for the .32 interface. l2tpv2-client(3)is obsoleted and NOT supported. bridge(1): Sets individual interface to bridging mode (for IPv6 interfaces DHCPv6 is external) router(2): Sets individual interface to routing mode (for IPv6 interfaces DHCPv6 is internal) l2tpv2-client(3): <obsolete> mixed(4): For mixed mode. This setting is applicable only to .32 interface. This value is used on conjunction with saRgIpMgmtLanPortControlTable *Note: mixed(4) mode NOT Supported by DOCSIS 2.0 products. vlan (5): Enables the vlan control feature. See saRgVlanTable MIBs for VLAN configuration information.rw Enumeration .1.3.6.1.4.1.1429.79.2.3.2.1.1 |
saRgIpMgmtLanNetworkThe LAN-Trans network number. Default for primary BSS is 192.168.0.0 Default for other BSSs is 192.168.ifIndex.0rw IpAddress .1.3.6.1.4.1.1429.79.2.3.2.1.3 |
saRgIpMgmtLanNetworksAllowAllows the user via the internal Web GUI (Lan Setup page to input an IPv4 public or private Local IP address other than a class C Private address (the default Network for the Primary BSS = 192.168.0.0/24, with the default Local Ip address = 192.168.0.1.) In all cases the mask must be 255.255.255.x since the RG is limited to supporting a maximum of 253 IP addresses. (See RFC1918 for a description of private IP addresses and specified ranges.) Available Mib settings: default(0): Only the third and fourth octets are editable in the Web GUI for the Local IP address (Ex. 192.168.x.x/24). anyPrivateClass(1): All 4 octets are editable in the Web GUI for Local IP address, but the network specified must be a Private class A, B or C network address. (Ex. A=10.x.x.x, B=172.16.x.x, C=192.168.x.x). anyClass(2): All 4 octets are editable in the Web GUI for Local IP address, and the network specified could be any public or private class A, B, or C address. If the MSO specifically sets a Local IP address in saRgIpMgmtLanNetwork to a value other than the default value (for example: 192.168.0.1) then these fields will be uneditable by the user (grayed out).rw Enumeration .1.3.6.1.4.1.1429.79.2.3.2.1.4 |
saRgIpMgmtLanSubnetMaskThe device MUST provide the value of this MIB object in the Option 1 (Subnet Mask) of DHCP OFFER and ACK messages sent to a LAN IP Device.rw IpAddress .1.3.6.1.4.1.1429.79.2.3.2.1.5 |
saRgIpMgmtLanGatewayThe type of this address is specified by saRgIpMgmtLanNetwokRouterType. The PS MUST provide the value of this MIB object in the Option 3 (Router IP address) of the DHCP OFFER and ACK messages sent to the LAN IP Device. Default for primary BSS is 192.168.0.1 Default for other BSSs is 192.168.ifIndex.1rw IpAddress .1.3.6.1.4.1.1429.79.2.3.2.1.7 |
saRgIpMgmtLanDhcpServerThe value for primary BSS is stored in non-vol. The default value for other BSSs is: Enabled by default if interface is in router mode. Always disabled if interface is in bridge mode.rw Enumeration .1.3.6.1.4.1.1429.79.2.3.2.1.8 |
saRgIpMgmtLanNaptThe value for primary BSS is stored in non-vol. The default value for other BSSs is: Enabled by default if interface is in router mode. Always disabled if interface is in bridge mode.rw Enumeration .1.3.6.1.4.1.1429.79.2.3.2.1.9 |
saRgIpMgmtLanTypeOfServiceDefinition of the TOS bits for the Network. This object does not apply to primary BSS.rw INTEGER .1.3.6.1.4.1.1429.79.2.3.2.1.10 |
saRgIpMgmtLanDhcp125OptionThis option controls if the RG adds a Cisco specific suboption (number 17) to DHCP DISCOVER and REQUEST from the clients that are bridged on the BSS: 0: do not add the option 1: add suboption 17 to Cisco specific enterprise-id (9) within DHCP option 125. The content is the SSID name.rw Enumeration .1.3.6.1.4.1.1429.79.2.3.2.1.11 |
saRgIpMgmtLanUpnpEnable/Disable the UPnP agent. The value is stored in non-vol and is disabled after factory default for the primary SSID. The UPnP agents for additional networks are enabled by default.rw Enumeration .1.3.6.1.4.1.1429.79.2.3.2.1.13 |
saRgIpMgmtLanDhcpOption43If option 60 is set from the CPE then return this value in option 43 of the DHCP Reply. If this value is null then do not reply with option 43 (default is null) This MIB will apply to the Primary SSID (intface .32) onlyrw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.1429.79.2.3.2.1.14 |
saRgIpMgmtLanDhcpServerTableNetworks on the LAN side. Stored in non-vol. .10-.128 for primary BSS after factory reset. SEQUENCE OF SaRgIpMgmtLanDhcpServerEntry .1.3.6.1.4.1.1429.79.2.3.3 |
saRgIpMgmtLanDhcpServerEntryList of networks on the LAN side. SaRgIpMgmtLanDhcpServerEntry .1.3.6.1.4.1.1429.79.2.3.3.1 |
saRgIpMgmtLanDhcpServerPoolStartThe start of range LAN Trans IP Addresses. The type of this address is specified by saRgIpMgmtLanDhcpServerPoolStartType. Default value depends on IP network and subnet.rw IpAddress .1.3.6.1.4.1.1429.79.2.3.3.1.2 |
saRgIpMgmtLanDhcpServerPoolEndThe end of range for LAN-Trans IP Addresses. The type of this address is specified by saRgIpMgmtLanDhcpServerPoolEndType. Default value depends on IP network and subnet.rw IpAddress .1.3.6.1.4.1.1429.79.2.3.3.1.4 |
saRgIpMgmtLanDhcpServerLeaseTimeThe PS MUST provide the value of this MIB object in the Option 51 (IP Address lease time) of the DHCP OFFER and ACK messages sent to the LAN IP Device.rw Unsigned32 UNITS "seconds" .1.3.6.1.4.1.1429.79.2.3.3.1.5 |
saRgIpMgmtLanAddrTableIP addresses of devices served by DHCP servers. SEQUENCE OF SaRgIpMgmtLanAddrEntry .1.3.6.1.4.1.1429.79.2.3.4 |
saRgIpMgmtLanAddrEntryList of general parameters pertaining to LAN-Trans IP address reservations and leases. SaRgIpMgmtLanAddrEntry .1.3.6.1.4.1.1429.79.2.3.4.1 |
saRgIpMgmtLanAddrIndexThe index of the the LAN IP Device in the LAN-Trans Realm. INTEGER .1.3.6.1.4.1.1429.79.2.3.4.1.1 |
saRgIpMgmtLanAddrIpro IpAddress .1.3.6.1.4.1.1429.79.2.3.4.1.3 |
saRgIpMgmtLanAddrPhysAddrThe client's (i.e., LAN IP Device's) hardware address as indicated in the chaddr field of its DHCP REQUEST message.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.3.4.1.4 |
saRgIpMgmtLanAddrLeaseCreateTimeThis is the date and time when the LAN IP lease was created (if it has not yet been renewed) or last renewed.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.3.4.1.5 |
saRgIpMgmtLanAddrLeaseExpireTimeThis is the date and time when the LAN IP address lease expired or will expire.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.3.4.1.6 |
saRgIpMgmtLanAddrHostNameThis is the Host Name of the LAN IP address, based on DCHP option 12.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.1429.79.2.3.4.1.7 |
saRgIpMgmtLanAddrClientIdThis is the Client Class Identifier, based on DHCP option 60.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.1429.79.2.3.4.1.8 |
saRgIpMgmtLanAddrInterfaceThis will show the associated interface (LAN, WiFi or MoCA) of the connected CPE.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.1429.79.2.3.4.1.9 |
saRgIpMgmtDnsServerTableThis table contains the IP addresses of cable network and Internet DNS servers, in the order of preference in which the PS's CNP will query them, when it cannot resolve a DNS query using local information. Entries in this table are updated with the information contained in DHCP Option 6, received during both the WAN-Man and WAN-Data IP acquisition processes. Stored in non-vol and 0.0.0.0 for all servers after factory reset. SEQUENCE OF SaRgIpMgmtDnsServerEntry .1.3.6.1.4.1.1429.79.2.3.5 |
saRgIpMgmtDnsServerEntryList of cable network and Internet DNS servers. SaRgIpMgmtDnsServerEntry .1.3.6.1.4.1.1429.79.2.3.5.1 |
saRgIpMgmtDnsServerIpThis parameter indicates the IP address of a WAN DNS server.rw IpAddress .1.3.6.1.4.1.1429.79.2.3.5.1.3 |
saRgIpMgmtDhcpFixedIpTableFixed IP address assignments for DHCP server. Table does not return any row if DHCP disabled. The value for primary BSS is stored in non-vol. SEQUENCE OF SaRgIpMgmtDhcpFixedIpEntry .1.3.6.1.4.1.1429.79.2.3.6 |
saRgIpMgmtDhcpFixedIpEntryList of general parameters pertaining to LAN-Trans IP address reservations and leases. SaRgIpMgmtDhcpFixedIpEntry .1.3.6.1.4.1.1429.79.2.3.6.1 |
saRgIpMgmtDhcpFixedIpIndexThe index of the the LAN IP Device in the LAN-Trans Realm. INTEGER .1.3.6.1.4.1.1429.79.2.3.6.1.1 |
saRgIpMgmtDhcpFixedIpRowStatusThe row status. A row can be destroyed.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.3.6.1.2 |
saRgIpMgmtDhcpFixedIpAddressrw IpAddress .1.3.6.1.4.1.1429.79.2.3.6.1.4 |
saRgIpMgmtDhcpFixedIpPhysAddrThe client's (i.e., LAN IP Device's) hardware address as indicated in the chaddr field of its DHCP REQUEST message.rw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.3.6.1.5 |
saRgIpMgmtDhcpFixedIpHostNameThis is the Host Name of the LAN IP address, based on DCHP option 12.rw SnmpAdminString .1.3.6.1.4.1.1429.79.2.3.6.1.6 |
saRgIpMgmtStaticRouteTableStatic route entries in the routing table. This table is saved in non-vol and is empty after factory reset. SEQUENCE OF SaRgIpMgmtStaticRouteEntry .1.3.6.1.4.1.1429.79.2.3.8 |
saRgIpMgmtStaticRouteEntryList of static route entries in the routing table. SaRgIpMgmtStaticRouteEntry .1.3.6.1.4.1.1429.79.2.3.8.1 |
saRgIpMgmtStaticRouteIndexThe index of the the table. INTEGER .1.3.6.1.4.1.1429.79.2.3.8.1.1 |
saRgIpMgmtStaticRouteRowStatusThe row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.3.8.1.2 |
saRgIpMgmtStaticRouteNetworkStatic route IP network definitionrw IpAddress .1.3.6.1.4.1.1429.79.2.3.8.1.3 |
saRgIpMgmtStaticRouteSubnetMaskStatic route network mask definitionrw IpAddress .1.3.6.1.4.1.1429.79.2.3.8.1.4 |
saRgIpMgmtStaticRouteGatewayGateway to the network defined in saRgIpMgmtStaticRouteNetwork and saRgIpMgmtStaticRouteSubnetMask.rw IpAddress .1.3.6.1.4.1.1429.79.2.3.8.1.5 |
saRgIpMgmtStaticRouteRipAdvertiseIf set to true(1), then static route entry will be advertised in RIP.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.3.8.1.6 |
saRgIpMgmtWanAddr OBJECT IDENTIFIER .1.3.6.1.4.1.1429.79.2.3.9 |
saRgIpMgmtWanAddrBase OBJECT IDENTIFIER .1.3.6.1.4.1.1429.79.2.3.9.1 |
saRgIpMgmtWanModeWhen dualIp(3) is selected, the second IP stack is used for user operations. Stored in non-vol, dhcp(1) after factory reset.rw Enumeration .1.3.6.1.4.1.1429.79.2.3.9.1.1 |
saRgIpMgmtWanMtuMTU size for the IP layer. Valid range is 256 to 1500. 0 is the default which is 1500. Stored in non-vol, 0 after factory reset.rw INTEGER .1.3.6.1.4.1.1429.79.2.3.9.1.2 |
saRgIpMgmtWanTtlTTL for the IP packets forwarded to WAN. 0 means no change to the original TTL (after being decreased by 1). Stored in non-vol, 0 after factory reset.rw INTEGER .1.3.6.1.4.1.1429.79.2.3.9.1.3 |
saRgIpMgmtWanAddrStatic OBJECT IDENTIFIER .1.3.6.1.4.1.1429.79.2.3.9.3 |
saRgIpMgmtWanStaticNetworkStored in non-vol, 0.0.0.0 after factory reset.rw IpAddress .1.3.6.1.4.1.1429.79.2.3.9.3.1 |
saRgIpMgmtWanStaticSubnetMaskStored in non-vol, 0.0.0.0 after factory reset.rw IpAddress .1.3.6.1.4.1.1429.79.2.3.9.3.2 |
saRgIpMgmtWanStaticGatewayStored in non-vol, 0.0.0.0 after factory reset.rw IpAddress .1.3.6.1.4.1.1429.79.2.3.9.3.3 |
saRgIpMgmtWanAddrDualIp OBJECT IDENTIFIER .1.3.6.1.4.1.1429.79.2.3.9.4 |
saRgIpMgmtWanDualIpAddrIP address for the second IP stack. If not specified and saRgIpMgmtWanMode is set to dualIp(3), DHCP is used to acquire the IP address. Note: this object can only be set from config file.ro IpAddress .1.3.6.1.4.1.1429.79.2.3.9.4.1 |
saRgIpMgmtWanDualIpRipAdvertisedSpecifies if the IP address is to be advertised in RIP, if RIP is enabled. Note: this object can only be set from config file.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.3.9.4.2 |
saRgIpMgmtLanExtraSubnetTableAdditional IP addresses for primary LAN interface. If RIP is enabled, all subnets are advertised. All objects are stored in non-vol. The table is empty after factory reset. SEQUENCE OF SaRgIpMgmtLanExtraSubnetEntry .1.3.6.1.4.1.1429.79.2.3.11 |
saRgIpMgmtLanExtraSubnetEntryList of networks on the LAN side. SaRgIpMgmtLanExtraSubnetEntry .1.3.6.1.4.1.1429.79.2.3.11.1 |
saRgIpMgmtLanExtraSubnetIndexIndicates the instance of this table row. Enumeration .1.3.6.1.4.1.1429.79.2.3.11.1.1 |
saRgIpMgmtLanExtraSubnetRowStatusThe row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.3.11.1.2 |
saRgIpMgmtLanExtraSubnetIpAddressrw IpAddress .1.3.6.1.4.1.1429.79.2.3.11.1.3 |
saRgIpMgmtLanExtraSubnetSubnetMaskrw IpAddress .1.3.6.1.4.1.1429.79.2.3.11.1.4 |
saRgIpMgmtLanExtraSubnetGatewayrw IpAddress .1.3.6.1.4.1.1429.79.2.3.11.1.5 |
saRgIpMgmtLanPortControl OBJECT IDENTIFIER .1.3.6.1.4.1.1429.79.2.3.13 |
saRgIpMgmtLanPortControlTableTable to control the mode for each LAN PORT. LAN PORTs are numbered 1-4 and are mapped to physical port location. Each port can either be in router or in bridge mode. SEQUENCE OF SaRgIpMgmtLanPortControlEntry .1.3.6.1.4.1.1429.79.2.3.13.1 |
saRgIpMgmtLanPortControlEntry SaRgIpMgmtLanPortControlEntry .1.3.6.1.4.1.1429.79.2.3.13.1.1 |
saRgIpMgmtLanPortControlIndexThe index for each LAN port INTEGER .1.3.6.1.4.1.1429.79.2.3.13.1.1.1 |
saRgIpMgmtLanPortModeEach physical LAN port can either be controlled as bridge or router. The saRgIpMgmtLanPortMode MIB only works when SaRgIpMgmtLanMode.32=4(Mixed). Setting this MIB through SNMP will take effect only after saRgIpMgmtApplySettings.0 set to true and this setting will reboot to take effectrw Enumeration .1.3.6.1.4.1.1429.79.2.3.13.1.1.2 |
saRgIpMgmtApplySettingsIf set to true(1), then all the settings (MIB values) from this MIB tree will be applied to run time configuration, modifying previous RG operation with the new settings. Before setting the value to true, MIBs modified in the MIB tree are stored in non-vol and will not modify RG operation until saRgIpMgmtApplySettings is set to true or CM resets. Note: this applies only to the MIB objects that are stored in non-vol. Always returns false(2) when read.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.3.1001 |
saRgFirewall OBJECT IDENTIFIER .1.3.6.1.4.1.1429.79.2.4 |
saRgFirewallReport OBJECT IDENTIFIER .1.3.6.1.4.1.1429.79.2.4.4 |
saRgFirewallReportEventTableThis table is stored in non-vol and is empty after factory reset. SEQUENCE OF SaRgFirewallReportEventEntry .1.3.6.1.4.1.1429.79.2.4.4.1 |
saRgFirewallReportEventEntry SaRgFirewallReportEventEntry .1.3.6.1.4.1.1429.79.2.4.4.1.1 |
saRgFirewallReportEventIndexThe index INTEGER .1.3.6.1.4.1.1429.79.2.4.4.1.1.1 |
saRgFirewallReportEventDescriptionro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.1429.79.2.4.4.1.1.2 |
saRgFirewallReportEventCountro INTEGER .1.3.6.1.4.1.1429.79.2.4.4.1.1.3 |
saRgFirewallReportEventLastOccurancero SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.1429.79.2.4.4.1.1.4 |
saRgFirewallReportEventTargetro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.1429.79.2.4.4.1.1.5 |
saRgFirewallReportEventSourcero SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.1429.79.2.4.4.1.1.6 |
saRgFirewallReportMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.1429.79.2.4.4.2 |
saRgFirewallReportMgmtClearLogNote: this object does not need saRgFirewallApplySettings to take effect.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.4.4.2.1 |
saRgFirewallReportEmailLogNowTriggers sending currect logs via email. Always returns false. Note: this objects does not need saRgFirewallApplySettings to send the logs.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.4.4.2.2 |
saRgFirewallReportEmail OBJECT IDENTIFIER .1.3.6.1.4.1.1429.79.2.4.4.3 |
saRgFirewallReportEmailEnableEnables sending logs via email. Email is sent when an event happens.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.4.4.3.1 |
saRgFirewallReportEmailAddressThis is stored in non-vol and is empty after factory reset.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.1429.79.2.4.4.3.2 |
saRgFirewallReportEmailSmtpServerIP address or FQDN. Stored in non-vol. Empty after factory reset.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.1429.79.2.4.4.3.3 |
saRgFirewallReportEmailUsernameThis is stored in non-vol and is empty after factory reset.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.1429.79.2.4.4.3.4 |
saRgFirewallReportEmailPasswordThis is stored in non-vol and is empty after factory reset.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.1429.79.2.4.4.3.5 |
saRgFirewallRules OBJECT IDENTIFIER .1.3.6.1.4.1.1429.79.2.4.5 |
saRgFirewallIpFilterTableThis table is stored in non-vol and is empty after factory reset. SEQUENCE OF SaRgFirewallIpFilterEntry .1.3.6.1.4.1.1429.79.2.4.5.1 |
saRgFirewallIpFilterEntry SaRgFirewallIpFilterEntry .1.3.6.1.4.1.1429.79.2.4.5.1.1 |
saRgFirewallIpFilterIndexThe index INTEGER .1.3.6.1.4.1.1429.79.2.4.5.1.1.1 |
saRgFirewallIpFilterRowStatusThe row status. A row can be destroyed. If the row is not used, set to notInService.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.4.5.1.1.2 |
saRgFirewallIpFilterAddressStartrw IpAddress .1.3.6.1.4.1.1429.79.2.4.5.1.1.3 |
saRgFirewallIpFilterAddressEndrw IpAddress .1.3.6.1.4.1.1429.79.2.4.5.1.1.4 |
saRgFirewallPortFilterTableThis table is stored in non-vol and is empty after factory reset. SEQUENCE OF SaRgFirewallPortFilterEntry .1.3.6.1.4.1.1429.79.2.4.5.2 |
saRgFirewallPortFilterEntry SaRgFirewallPortFilterEntry .1.3.6.1.4.1.1429.79.2.4.5.2.1 |
saRgFirewallPortFilterIndexThe index INTEGER .1.3.6.1.4.1.1429.79.2.4.5.2.1.1 |
saRgFirewallPortFilterRowStatusThe row status. A row can be destroyed. If the row is not used, set to notInService.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.4.5.2.1.2 |
saRgFirewallPortFilterPortStartrw InetPortNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.1429.79.2.4.5.2.1.5 |
saRgFirewallPortFilterPortEndrw InetPortNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.1429.79.2.4.5.2.1.6 |
saRgFirewallPortFilterProtoIP protocol to block.rw Enumeration .1.3.6.1.4.1.1429.79.2.4.5.2.1.7 |
saRgFirewallMacFilterTableA table of clients MAC addresses that are denied from accessing Internet. SEQUENCE OF SaRgFirewallMacFilterEntry .1.3.6.1.4.1.1429.79.2.4.5.3 |
saRgFirewallMacFilterEntryA row in the table that specifies a single station MAC address. SaRgFirewallMacFilterEntry .1.3.6.1.4.1.1429.79.2.4.5.3.1 |
saRgFirewallMacFilterIndexThe index INTEGER .1.3.6.1.4.1.1429.79.2.4.5.3.1.1 |
saRgFirewallMacFilterRowStatusThe row status. A row can be destroyed. If the row is not used, set to notInService.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.4.5.3.1.2 |
saRgFirewallMacFilterAddressA MAC address of a station that cannot access Internet.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.4.5.3.1.3 |
saRgFirewallMacFilterEnableTrue = Enable the Mac address filtering feature. False = disable. this Value is written to non-vol and set to false after a factory reset.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.4.5.4 |
saRgFirewallMacFilterModeblock(0)- Macs listed in the saRgFirewallMacFilterEntryTable will be blocked. permit(1)- Macs listed in the saRgFirewallMacFilterEntryTable will be permitted. This value is written to non-vol and is set to block(0) after a factory reset.rw Enumeration .1.3.6.1.4.1.1429.79.2.4.5.5 |
saRgFirewallPortFwdTableThis table is stored in non-vol and is empty after factory reset. SEQUENCE OF SaRgFirewallPortFwdEntry .1.3.6.1.4.1.1429.79.2.4.6 |
saRgFirewallPortFwdEntry SaRgFirewallPortFwdEntry .1.3.6.1.4.1.1429.79.2.4.6.1 |
saRgFirewallPortFwdIndexThe index INTEGER .1.3.6.1.4.1.1429.79.2.4.6.1.1 |
saRgFirewallPortFwdRowStatusThe row status. A row can be destroyed. If the row is not used, set to notInService.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.4.6.1.2 |
saRgFirewallPortFwdToAddressValid address must be entered for a row to be created.rw IpAddress .1.3.6.1.4.1.1429.79.2.4.6.1.3 |
saRgFirewallPortFwdPortStartValid port must be entered for a row to be created.rw InetPortNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.1429.79.2.4.6.1.4 |
saRgFirewallPortFwdPortEndValid port must be entered for a row to be created.rw InetPortNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.1429.79.2.4.6.1.5 |
saRgFirewallPortFwdProtorw Enumeration .1.3.6.1.4.1.1429.79.2.4.6.1.6 |
saRgFirewallPortFwdExternalPortStartValid port must be entered for a row to be created. This is the outside-facing start port for the portforward.rw InetPortNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.1429.79.2.4.6.1.8 |
saRgFirewallPortFwdExternalPortEndValid port must be entered for a row to be created. This is the outside-facing end port for the portforward.rw InetPortNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.1429.79.2.4.6.1.9 |
saRgFirewallPortTrigTableThis table is stored in non-vol and is empty after factory reset. SEQUENCE OF SaRgFirewallPortTrigEntry .1.3.6.1.4.1.1429.79.2.4.7 |
saRgFirewallPortTrigEntry SaRgFirewallPortTrigEntry .1.3.6.1.4.1.1429.79.2.4.7.1 |
saRgFirewallPortTrigIndexThe index INTEGER .1.3.6.1.4.1.1429.79.2.4.7.1.1 |
saRgFirewallPortTrigRowStatusThe row status. A row can be destroyed. If the row is not used, set to notInService.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.4.7.1.2 |
saRgFirewallPortTrigTriggerPortStartrw InetPortNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.1429.79.2.4.7.1.3 |
saRgFirewallPortTrigTriggerPortEndrw InetPortNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.1429.79.2.4.7.1.4 |
saRgFirewallPortTrigTargetPortStartrw InetPortNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.1429.79.2.4.7.1.5 |
saRgFirewallPortTrigTargetPortEndrw InetPortNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.1429.79.2.4.7.1.6 |
saRgFirewallPortTrigProtorw Enumeration .1.3.6.1.4.1.1429.79.2.4.7.1.7 |
saRgFirewallApplySettingsIf set to true(1), then all the settings (MIB values) from this MIB tree will be applied to run time configuration, modifying previous RG operation with the new settings. Before setting the value to true, MIBs modified in the MIB tree are stored in non-vol and will not modify RG operation until saRgFirewallApplySettings is set to true or CM resets. Note: this applies only to the MIB objects that are stored in non-vol. Always returns false(2) when read.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.4.1001 |
saRgDslite OBJECT IDENTIFIER .1.3.6.1.4.1.1429.79.2.12 |
saRgDsliteOptionThis MIB will toggle whether DHCPv6 option 64 is requested in the solicit. The option should only be requested if DS Lite is enabled.rw Enumeration .1.3.6.1.4.1.1429.79.2.12.1 |
saRgDsliteAftrNameThis MIB will read/write the remote IPv6 FQDN of the AFTR router in the DS Lite tunnel configuration. This should only have an effect if eRouter is in IPv6 only mode and DS Lite is enabled.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.1429.79.2.12.2 |
saRgDsliteAftrAddressThis MIB will set the remote IPv6 address of the AFTR router manually in the DS Lite tunnel configuration. This should only have an effect if eRouter is in IPv6 only mode and DS Lite is enabled.rw InetAddressIPv6 (INET-ADDRESS-MIB) .1.3.6.1.4.1.1429.79.2.12.3 |
saRgDsliteTcpMssClampingSpecifies whether TCP MSS clamping is enabled on the interface. 0 disables clamping, 1 clamps the MSS depending on the interface MTU. A value > 1 will be used as clamping size. This MIB takes effect immediately and does not require saRgDsliteApplySettings.rw INTEGER .1.3.6.1.4.1.1429.79.2.12.4 |
saRgDsliteApplySettingsIf set to true(1), then all the settings (MIB values) from this MIB tree will be applied to the runtime configuration, This will resolve the AFTR domain name to the AFTR IPv6 address, and initialize the DSlite tunnel. This will initialize using the AFTR address if both the address and FQDN are defined. This should only activate the tunnel if eRouter is in IPv6 only mode and DS Lite is enabled. Always returns false(2) when read.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1429.79.2.12.1001 |