RING-MIB
AI MIB Summary
The RING-MIB module facilitates the monitoring and management of Coriolis ring network topologies, specifically tracking ring port states, topology changes, and loop prevention mechanisms within Coriolis switching hardware.
The MIB module for coriolis rings
Main OID:
ringMIB.1.3.6.1.4.1.3181.10.6.2.45.8
103
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
103 total| Object Name |
|---|
actPhyRingCountActual number of physical rings passing through the devicero INTEGER .1.3.6.1.4.1.3181.10.6.2.45.1 |
actPhyRingTableThe actual physical ring table. The number of entries in this
table is given by actPhyRingCount SEQUENCE OF ActPhyRingEntry .1.3.6.1.4.1.3181.10.6.2.45.2 |
actPhyRingEntryEntry containing information about the attributes of actual
physical rings passing through a device ActPhyRingEntry .1.3.6.1.4.1.3181.10.6.2.45.2.1 |
phyRingSlotNoThe slot number for the physical ringro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.2.1.1 |
phyRingPortNoThe port number of the physical ringro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.2.1.2 |
actLogRingCountActual number of logical rings passing through the devicero INTEGER .1.3.6.1.4.1.3181.10.6.2.45.3 |
actLogRingTableThe actual logical ring table. The number of entries in this
table is given by actLogRingCount SEQUENCE OF ActLogRingEntry .1.3.6.1.4.1.3181.10.6.2.45.4 |
actLogRingEntryEntry containing information about the attributes of actual
logical rings passing through a device ActLogRingEntry .1.3.6.1.4.1.3181.10.6.2.45.4.1 |
logRingVPortNoThe lambda number of the logical ring if applicable, else 0ro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.4.1.1 |
logRingElemCountNumber of Elements on this logical ringro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.4.1.2 |
logRingLambdaStatusThe status of the lambda for the logical ringro Enumeration .1.3.6.1.4.1.3181.10.6.2.45.4.1.3 |
logRingProtoStatusTxtThe ascii text describing the protocol status of the ringro OCTET STRING .1.3.6.1.4.1.3181.10.6.2.45.4.1.5 |
logRingProtoStatusThe protocol status of the logical ringro Enumeration .1.3.6.1.4.1.3181.10.6.2.45.4.1.6 |
logRingGneNameThe name of the GNE on the ring.ro OCTET STRING .1.3.6.1.4.1.3181.10.6.2.45.4.1.7 |
logRingGneIpAddrThe IP address of the GNE on the ring.ro IpAddress .1.3.6.1.4.1.3181.10.6.2.45.4.1.8 |
logRingGneRingSlotThe slot of the connected GNE ring.ro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.4.1.9 |
logRingGneRingPortThe port of the connected GNE ring.ro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.4.1.10 |
logRingGneRingVportThe virtual port of the connected GNE ring.ro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.4.1.11 |
logRingUpsNgbrNameThe name of the upstream neighbor on the ring.ro OCTET STRING .1.3.6.1.4.1.3181.10.6.2.45.4.1.12 |
logRingUpsNgbrIpAddrThe IP address of the upstream neighbor on the ring.ro IpAddress .1.3.6.1.4.1.3181.10.6.2.45.4.1.13 |
logRingUpsNgbrRingSlotThe slot of the connected upstream neighbors ring.ro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.4.1.14 |
logRingUpsNgbrRingPortThe port of the connected upstream neighbors ring.ro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.4.1.15 |
logRingUpsNgbrRingVportThe virtual port of the connected upstream neighbors ring.ro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.4.1.16 |
logRingIsConfiguredWhether this ring has been configured by NMro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3181.10.6.2.45.4.1.17 |
logRingAttRingTypeThis object provides the type of the ring.ro Enumeration .1.3.6.1.4.1.3181.10.6.2.45.4.1.18 |
logRingCapacityThe capacity of the ring.ro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.4.1.19 |
logRingCutLocationIpIP address of the element where ring is cut.ro IpAddress .1.3.6.1.4.1.3181.10.6.2.45.4.1.20 |
logRingCutLocationNameName of the element where ring is cut.ro OCTET STRING .1.3.6.1.4.1.3181.10.6.2.45.4.1.21 |
logRingIsRingMasterWhether this node is master on the ring.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3181.10.6.2.45.4.1.22 |
logRingOtherSlotThe slot of the other(for working, it's protected or vice versa) ring.ro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.4.1.23 |
logRingOtherPortThe port of the other(for working, it's protected or vice versa) ring.ro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.4.1.24 |
logRingOtherVportThe vport of the other(for working, it's protected or vice versa) ring.ro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.4.1.25 |
actLogRingElemTableThe actual logical ring topology table. This describes the Elements on
a logical ring SEQUENCE OF ActLogRingElemEntry .1.3.6.1.4.1.3181.10.6.2.45.5 |
actLogRingElemEntryEntry containing information about the Elements on a logical ring ActLogRingElemEntry .1.3.6.1.4.1.3181.10.6.2.45.5.1 |
logRingElemIndexThe position of the Element on the ring starting from the transmit side of GNEro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.5.1.1 |
logRingElemNameThe name of the Elementro OCTET STRING .1.3.6.1.4.1.3181.10.6.2.45.5.1.2 |
logRingElemMACAddrThe MAC address of the Elementro OCTET STRING .1.3.6.1.4.1.3181.10.6.2.45.5.1.3 |
logRingElemIpAddrThe IP address of the Elementro IpAddress .1.3.6.1.4.1.3181.10.6.2.45.5.1.4 |
logRingElemPortIdThe port id for the logical ring on this NEro OCTET STRING .1.3.6.1.4.1.3181.10.6.2.45.5.1.5 |
logRingElemChassisIdThe chassis identifier of the Elementro Enumeration .1.3.6.1.4.1.3181.10.6.2.45.5.1.6 |
logRingElemActiveMMThe active management module of the Elementro Enumeration .1.3.6.1.4.1.3181.10.6.2.45.5.1.7 |
logRingElemIsInNeTableIndicates whether this element has it's entry in the cfgNeTablero TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3181.10.6.2.45.5.1.8 |
logRingElemIsReachableIndicates whether this element is reachable on this ring.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3181.10.6.2.45.5.1.9 |
logRingElemIsLambdaCutHereIndicates whether there is a lambda cut at this element.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3181.10.6.2.45.5.1.10 |
logRingElemChassisCharacterThe chassis character of the element.ro Enumeration .1.3.6.1.4.1.3181.10.6.2.45.5.1.11 |
logRingElemNodeIdThe node id of the element on the ring. Value 64 means element
doesn't have node id.ro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.5.1.12 |
logRingElemRxSegCutSeverityThe cut severity of RX segement of this element on the ring. Cut
severity indicates the effect of cutting RX segment on service level.
noLoss => segment doesn't carry any user traffic
sonetProtection => segment carries user traffic but 50ms restoration
is available if segment is cut.
serviceAffecting => segment carries user traffic but 50ms restoration
is not available. This could be because of either
ring is configured in unprotected mode or
existing cut in the ring.ro Enumeration .1.3.6.1.4.1.3181.10.6.2.45.5.1.13 |
cfgRingCountThe number of configured ringsro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.6 |
cfgRingTableThe configured ring table. The number of entries in this
table is given by cfgRingCount SEQUENCE OF CfgRingEntry .1.3.6.1.4.1.3181.10.6.2.45.7 |
cfgRingEntryEntry containing information about the attributes of configured
rings passing through a device CfgRingEntry .1.3.6.1.4.1.3181.10.6.2.45.7.1 |
cfgRingRowStatusThe row status variable. In order to modify the attributes of the ring
ring has to be put in out-of-service first.rw Enumeration .1.3.6.1.4.1.3181.10.6.2.45.7.1.1 |
cfgRingAdminCostAdmin cost of the ring. In the normal case, all rings should have same
admin cost. Whenever a ring is needed to be serviced, increase the admin
cost of the ring. This would force the GNE to move off TCs one by one of
the ring if there is alternate path available with lower admin cost. This
way there will not be a sudden disruption in the case where you bring the
ring down suddenly.rw INTEGER .1.3.6.1.4.1.3181.10.6.2.45.7.1.2 |
cfgRingNameThe name of the configured ringrw DisplayString .1.3.6.1.4.1.3181.10.6.2.45.7.1.3 |
cfgRingMeshFactorTraffic pattern on ring. The value varies between 1 (in case of hub traffic
pattern)and n/2 (in case of mesh traffic pattern) where n is number of nodes
in ring. This describes the inter-connection topology between nodes of the ring.
Internally this factor is multiplied by n-1 to get the number of
inter-connections between nodes of the ring.rw INTEGER .1.3.6.1.4.1.3181.10.6.2.45.7.1.4 |
cfgRingEirOverSubOver subscription percentage on EIR portion of BW allocated on ringrw INTEGER .1.3.6.1.4.1.3181.10.6.2.45.7.1.5 |
cfgRingProtectModeThe protection mode of the ringrw Enumeration .1.3.6.1.4.1.3181.10.6.2.45.7.1.6 |
cfgRingExceptNesComma separated list of IP address that are physically present on the ring
but no connections are allowed to be setup. This is useful for traffic
management where there is a bandwidth crunch on the ring. But some of the
NEs on that particular ring have alternate paths through the other rings.rw DisplayString .1.3.6.1.4.1.3181.10.6.2.45.7.1.7 |
cfgRingNeTopoDesired topology of the ring (starting from transmit direction) in the form
of comma separated list of IP addresses. If the actual topology mismatches
with the desired topology, an event get generated.rw DisplayString .1.3.6.1.4.1.3181.10.6.2.45.7.1.8 |
cfgRingIpModeSource of ip addresses of NEs. If it is gneSupplied, GNE over writes
the ip address of NE from its configured tables. Otherwise it takes it
from NE itselfrw Enumeration .1.3.6.1.4.1.3181.10.6.2.45.7.1.9 |
cfgRingFrameModeThe frame mode on the ringrw Enumeration .1.3.6.1.4.1.3181.10.6.2.45.7.1.10 |
cfgRingOperStatusThe operational status of the configured ringro Enumeration .1.3.6.1.4.1.3181.10.6.2.45.7.1.13 |
cfgRingCurNumTdmCktsThe number of TDM ckts traversing on the ring currently.ro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.7.1.14 |
cfgRingCurNumFreeChansThe number of free channels available on the ring currently.ro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.7.1.15 |
cfgRingNeAdminCostThe NE specific admin costs on the ring as comma separated list where
list entry is of form <ip address in dotted notation>:<admin cost>.
Admin costs for the NE's that are present on this ring but not specified
in this list are inherited from ring admin cost. Admin cost per NE per
ring is useful in traffic managementrw DisplayString .1.3.6.1.4.1.3181.10.6.2.45.7.1.16 |
cfgRingCurNumDataCktsThe number of data ckts traversing on the ring currently.ro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.7.1.17 |
cfgRingCurAllocTdmBwKbitsThe bandwidth on the ring that is currently being reserved by TDM ckts
passing through ring.ro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.7.1.18 |
cfgRingCurAllocCirBwKbitsThe bandwidth on the ring that is currently being reserved for CIR by
data ckts passing through the ring.ro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.7.1.19 |
cfgRingCurAllocEirBwKbitsThe bandwidth on the ring that is currently being reserved for EIR by
data ckts passing through the ring.ro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.7.1.20 |
cfgRingCurAvailBwKbitsThe current available bandwidth on the ringro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.7.1.21 |
cfgRingTdmAvgUtilPercentAverage ring utilization for TDM traffic since last resetro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.7.1.22 |
cfgRingTdmLastUtilPercentRing utilization for TDM traffic during last period.ro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.7.1.23 |
cfgRingTdmMaxUtilPercentMax. ring utilization for TDM traffic since last resetro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.7.1.24 |
cfgRingDataAvgUtilPercentAverage ring utilization for Data traffic since last resetro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.7.1.25 |
cfgRingDataLastUtilPercentRing utilization for Data traffic during last periodro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.7.1.26 |
cfgRingDataMaxUtilPercentMax. ring utilization for Data traffic since last resetro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.7.1.27 |
cfgRingTotalAvgUtilPercentAverage ring utlization for combined Data and TDM trafficro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.7.1.28 |
cfgRingTotalLastUtilPercentRing utilization for TDM and Data traffic during last periodro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.7.1.29 |
cfgRingTotalMaxUtilPercentMax. ring utilization for TDM and Data traffic since last resetro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.7.1.30 |
cfgRingTdmTrafficKbitsTDM traffic transmitted on ring since last resetro Counter64 .1.3.6.1.4.1.3181.10.6.2.45.7.1.31 |
cfgRingTdmLastTrafficKbitsTDM traffic transmitted on ring during current periodro Counter64 .1.3.6.1.4.1.3181.10.6.2.45.7.1.32 |
cfgRingDataTrafficKbitsData traffic transmitted on ring since last resetro Counter64 .1.3.6.1.4.1.3181.10.6.2.45.7.1.33 |
cfgRingDataLastTrafficKbitsData traffic trasnmitted on ring during last periodro Counter64 .1.3.6.1.4.1.3181.10.6.2.45.7.1.34 |
cfgRingDataNumPktsNumber of Data packets on ring since last resetro Counter64 .1.3.6.1.4.1.3181.10.6.2.45.7.1.35 |
cfgRingDataLastNumPktsNumber of Data packets on ring during last periodro Counter64 .1.3.6.1.4.1.3181.10.6.2.45.7.1.36 |
cfgRingStatsCollElapsedTimeThe time elapsed since the beginning of collection of ring statisticsro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.3181.10.6.2.45.7.1.37 |
cfgRingStatsPeriodTimeThe period of status collection intervalro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.3181.10.6.2.45.7.1.38 |
cfgRingTimeSinceLastOperStatusChangeThe time since the last change in the oper status of the ringro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.3181.10.6.2.45.7.1.39 |
cfgRingTdmMinUtilPercentMininum ring utilization for TDM traffic since last resetro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.7.1.40 |
cfgRingDataMinUtilPercentMininum ring utilization for data traffic since last resetro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.7.1.41 |
cfgRingTotalMinUtilPercentMininum ring utilization for combined TDM and Data traffic since
last resetro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.7.1.42 |
cfgRingAttUpsrSwitchCmdThis object defines the UPSR switch commands that amy be configured.
These commands are configurable and static. The priority of the
commands in relation to APS and revertive switching is given in
the enumeration above.rw Enumeration .1.3.6.1.4.1.3181.10.6.2.45.7.1.43 |
cfgRingIsRevertiveModeEnabledIf the revertive mode is enabled and the UPSR switch
command is clear, then, if the working ring gets cut,
the traffic is moved to the protected ring. When the
working ring is restored from the cut, traffic will
be reverted to the working ring.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3181.10.6.2.45.7.1.44 |
cfgRingWaitToRestorePeriodThis object provide the time period in minutes between the
time the working ring gets restored from the cut and the time
when the traffic is reverted to the working ring.rw INTEGER .1.3.6.1.4.1.3181.10.6.2.45.7.1.45 |
cfgRingCurTdmAvailBwKbitsThe current tdm available bandwidth on the ringro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.7.1.46 |
cfgRingCurDataAvailBwKbitsThe current pkt available bandwidth on the ringro INTEGER .1.3.6.1.4.1.3181.10.6.2.45.7.1.47 |
ringMIBThe MIB module for coriolis rings MODULE-IDENTITY .1.3.6.1.4.1.3181.10.6.2.45.8 |
RFC1155-SMIThe MIB module for coriolis rings Unknown .1.3.6.1.4.1.3181.10.6.2.45.8 |
ringOperStatusChangechange in operational status of a configured logical ring TRAP-TYPE .1.3.6.1.4.1.5812.0.3 |
neReachabilityChangechange in the reachability status of NE TRAP-TYPE .1.3.6.1.4.1.5812.0.4 |
lambdaStatusChangechange in the fiber status of the ring TRAP-TYPE .1.3.6.1.4.1.5812.0.5 |
ringProtoErrorStatusChangeRing error detected/cleared TRAP-TYPE .1.3.6.1.4.1.5812.0.6 |
ringProtoWarnStatusChangeRing warning detected/cleared TRAP-TYPE .1.3.6.1.4.1.5812.0.7 |
ringTopoChangeRing topology changed TRAP-TYPE .1.3.6.1.4.1.5812.0.56 |