G6-HARDWARE-MIB
AI MIB Summary
The G6-HARDWARE-MIB provides vendor-specific SNMP access to monitor physical layer telemetry and hardware status indicators, including temperature, fan speeds, and power supply states, for Microsens Generation 6 Ethernet switches. This module enables granular fault detection and environmental monitoring by exposing hardware component health metrics not covered by standard IETF MIBs.
Microsens private MIB for Generation 6 Ethernet Switches
Main OID:
device.1.3.6.1.4.1.3181.10.6.1
117
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
117 total| Object Name |
|---|
deviceMicrosens private MIB for Generation 6 Ethernet Switches MODULE-IDENTITY .1.3.6.1.4.1.3181.10.6.1 |
hardware OBJECT IDENTIFIER .1.3.6.1.4.1.3181.10.6.1.31 |
hardwareLedTestRuns a leds test whereby all LED light up in all possible colors for checking their function. The tests terminates within a few seconds.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3181.10.6.1.31.1 |
hardwareLedModeThe LED display can be configured to be less intrusive.rw Enumeration .1.3.6.1.4.1.3181.10.6.1.31.2 |
hardwarePowerSupply1MonitoredWhen disabled a missing power supply 1 will not turn the associated led red on failure. Do this when single power supply 2 operation is used or when the device is powered soley by PoE. This feature only applies to industrial switches.rw Enumeration .1.3.6.1.4.1.3181.10.6.1.31.3 |
hardwarePowerSupply2MonitoredWhen disabled a missing power supply 2 will not turn the associated led red on failure. Do this when single power supply 1 operation is used or when the device is powered soley by PoE. This feature only applies to industrial switches.rw Enumeration .1.3.6.1.4.1.3181.10.6.1.31.4 |
hardwareFactoryResetButtonWhen disabled the factory button will trigger the factory reset function when pressed for a long time. The IP discover function upon a short button click is not affected.rw Enumeration .1.3.6.1.4.1.3181.10.6.1.31.5 |
cableTestConfigTableThe cable tester allows for detection of copper cable faults and can even detect where the fault is located. SEQUENCE OF CableTestConfigEntry .1.3.6.1.4.1.3181.10.6.1.31.6 |
cableTestConfigEntry CableTestConfigEntry .1.3.6.1.4.1.3181.10.6.1.31.6.1 |
cableTestConfigPortIndexAutomatically generated INTEGER .1.3.6.1.4.1.3181.10.6.1.31.6.1.1 |
cableTestConfigEnableAutoCableTestWhen enabled a cable test is performed each time the link goes down. The test is only performed for copper ports or dual media ports in copper mode.rw Enumeration .1.3.6.1.4.1.3181.10.6.1.31.6.1.2 |
cableTestConfigEventGenerationWhen the cable termination status changes an event can be raised.rw Enumeration .1.3.6.1.4.1.3181.10.6.1.31.6.1.3 |
cableTestConfigStartTestNowMay be used to manually start a cable test. ATTENTION: If the port is in link up status it will be forced to link down first. This will disrupt the current data traffic. Therefore, type start_test_now = CONFIRM.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3181.10.6.1.31.6.1.4 |
ioSignalConfigTable SEQUENCE OF IoSignalConfigEntry .1.3.6.1.4.1.3181.10.6.1.31.7 |
ioSignalConfigEntry IoSignalConfigEntry .1.3.6.1.4.1.3181.10.6.1.31.7.1 |
ioSignalConfigIndexAutomatically generated INTEGER (0) .1.3.6.1.4.1.3181.10.6.1.31.7.1.1 |
ioSignalConfigSignalModePermit setting of io signal LEDs and relays to static or blink blink mode for increased visualization.rw Enumeration .1.3.6.1.4.1.3181.10.6.1.31.7.1.2 |
ioSignalConfigInput1ModeWhen this function is activated the external alarm input 1 is monitored. Note: alarm inputs are not available in all product versions.rw Enumeration .1.3.6.1.4.1.3181.10.6.1.31.7.1.3 |
ioSignalConfigInput1NameA customer specific name can be specified for input 1. This name will appear in the associated event messages.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3181.10.6.1.31.7.1.4 |
ioSignalConfigInput2ModeWhen this function is activated the external alarm input 2 is monitored. Note: alarm inputs are not available in all product versions.rw Enumeration .1.3.6.1.4.1.3181.10.6.1.31.7.1.5 |
ioSignalConfigInput2NameA customer specific name can be specified for input 2. This name will appear in the associated event messages.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3181.10.6.1.31.7.1.6 |
ioSignalConfigOutput1TriggerDefines on which condition the alarm relay 1 is activated. Note: alarm relays are not available in all product versions.rw Enumeration .1.3.6.1.4.1.3181.10.6.1.31.7.1.7 |
ioSignalConfigOutput1NameA customer specific name can be specified for alarm output 1. This name will appear in the associated event messages.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3181.10.6.1.31.7.1.8 |
ioSignalConfigOutput2TriggerDefines on which condition the alarm relay 2 is activated. Note: alarm relays are not available in all product versions.rw Enumeration .1.3.6.1.4.1.3181.10.6.1.31.7.1.9 |
ioSignalConfigOutput2NameA customer specific name can be specified for alarm output 2. This name will appear in the associated event messages.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3181.10.6.1.31.7.1.10 |
hardwarePowerSupply1StatusDisplays state of primary supply or only supply for single supply systems.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.100 |
hardwarePowerSupply2StatusDisplays state of secondary supply if available.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.101 |
hardwareRunningOnPoeWhen set the unit currently operates on the PD input via PoE.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.102 |
hardwareFanStatusDisplays state of cooling fan. Indicates UNUSED in fanless devices.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.103 |
hardwareSdCardStatusCurrent status of SD-card.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.104 |
hardwareNumOfPortsTotal number of Ethernet ports this hardware offers.ro Integer32 .1.3.6.1.4.1.3181.10.6.1.31.105 |
hardwareMaskOfExistingPortsSet bit for each port that physically exisiting and could be in use.ro INTEGER .1.3.6.1.4.1.3181.10.6.1.31.106 |
hardwareMaskOfSfpPortsMarks which ports support SFPs.ro INTEGER .1.3.6.1.4.1.3181.10.6.1.31.107 |
hardwareMaskOfPoePortsMarks which ports support PoE output.ro INTEGER .1.3.6.1.4.1.3181.10.6.1.31.108 |
moduleInfoTableThis section indicates which modules are inserted in the optional extension slots. SEQUENCE OF ModuleInfoEntry .1.3.6.1.4.1.3181.10.6.1.31.109 |
moduleInfoEntry ModuleInfoEntry .1.3.6.1.4.1.3181.10.6.1.31.109.1 |
moduleInfoIndexAutomatically generated INTEGER .1.3.6.1.4.1.3181.10.6.1.31.109.1.1 |
moduleInfoUnitTypeIdentfies the general type of module.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.109.1.2 |
moduleInfoArticleNumberThe article number of the module in this slot.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3181.10.6.1.31.109.1.3 |
moduleInfoSerialNumberThe serial number of the module in this slot.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3181.10.6.1.31.109.1.4 |
moduleInfoHardwareVersionThis device hardware revision number.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3181.10.6.1.31.109.1.5 |
moduleInfoProjectNumberMICROSENS project number.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3181.10.6.1.31.109.1.6 |
moduleInfoOccupiedSlotsLists all slots contained in this module.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3181.10.6.1.31.109.1.7 |
moduleInfoDescriptionFeature summary of the module.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3181.10.6.1.31.109.1.8 |
slotInfoTableThis section indicates which modules are inserted in the optional extension slots. SEQUENCE OF SlotInfoEntry .1.3.6.1.4.1.3181.10.6.1.31.110 |
slotInfoEntry SlotInfoEntry .1.3.6.1.4.1.3181.10.6.1.31.110.1 |
slotInfoIndexAutomatically generated INTEGER .1.3.6.1.4.1.3181.10.6.1.31.110.1.1 |
slotInfoBoardTypeGeneral type of board functionro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.110.1.2 |
slotInfoBoardIdThis identifies the board type for internal operation.ro Unsigned32 .1.3.6.1.4.1.3181.10.6.1.31.110.1.3 |
slotInfoVersionBitsVersion bits from hardware or backplane.ro Integer32 .1.3.6.1.4.1.3181.10.6.1.31.110.1.4 |
portInfoTableUsed to map physical to logical port ids. SEQUENCE OF PortInfoEntry .1.3.6.1.4.1.3181.10.6.1.31.111 |
portInfoEntry PortInfoEntry .1.3.6.1.4.1.3181.10.6.1.31.111.1 |
portInfoPortIndexAutomatically generated INTEGER .1.3.6.1.4.1.3181.10.6.1.31.111.1.1 |
portInfoSystemSlotDescribes on which system slot this port index is located.ro Integer32 .1.3.6.1.4.1.3181.10.6.1.31.111.1.2 |
portInfoSwitchPortDescribes on which switch port this port index is located.ro Integer32 .1.3.6.1.4.1.3181.10.6.1.31.111.1.3 |
portInfoUserSlotSlot number as seen by customer.ro Integer32 .1.3.6.1.4.1.3181.10.6.1.31.111.1.4 |
portInfoUserPortPort number as seen by customer.ro Integer32 .1.3.6.1.4.1.3181.10.6.1.31.111.1.5 |
portInfoSnmpPortSlot and port representation as used in SNMP. Formula is Slot*100 + Port.ro Integer32 .1.3.6.1.4.1.3181.10.6.1.31.111.1.6 |
portInfoSnmpInstancePort instance counting from 0 to number of portsro Integer32 .1.3.6.1.4.1.3181.10.6.1.31.111.1.7 |
portInfoHardwarePortPort number as used internally. Ports may not be in sequential order.ro Integer32 .1.3.6.1.4.1.3181.10.6.1.31.111.1.8 |
portInfoInterfaceTypeIdentifies port as copper or optical. Also used for snmp ifType definitionro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.111.1.9 |
portInfoPropertiesDescribes which functions the port can support.ro Bits .1.3.6.1.4.1.3181.10.6.1.31.111.1.10 |
portLedsTableThis section indicates the state of all port related LEDs. SEQUENCE OF PortLedsEntry .1.3.6.1.4.1.3181.10.6.1.31.112 |
portLedsEntry PortLedsEntry .1.3.6.1.4.1.3181.10.6.1.31.112.1 |
portLedsPortIndexAutomatically generated INTEGER .1.3.6.1.4.1.3181.10.6.1.31.112.1.1 |
portLedsEthernetColorEthernet Link LED.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.112.1.2 |
portLedsEthernetBlinkingEthernet Link LED.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.112.1.3 |
portLedsPoeColorPower over Ethernet LED. For optical ports this indicates signal detect status.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.112.1.4 |
portLedsPoeBlinkingPower over Ethernet LED. For optical ports this indicates signal detect status.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.112.1.5 |
deviceLedsTableThis section indicates the state of all LEDs which are not port related. Please note: Not every unit offers all LEDs. SEQUENCE OF DeviceLedsEntry .1.3.6.1.4.1.3181.10.6.1.31.113 |
deviceLedsEntry DeviceLedsEntry .1.3.6.1.4.1.3181.10.6.1.31.113.1 |
deviceLedsIndexAutomatically generated INTEGER (0) .1.3.6.1.4.1.3181.10.6.1.31.113.1.1 |
deviceLedsSystem1ColorThis status corresponds to 'sys' LED on some devices.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.113.1.2 |
deviceLedsSystem1BlinkingThis status corresponds to 'sys' LED on some devices.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.113.1.3 |
deviceLedsSystem2ColorDisplays external management activity.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.113.1.4 |
deviceLedsSystem2BlinkingDisplays external management activity.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.113.1.5 |
deviceLedsPowerOn1ColorThis status corresponds to 'on' LED on some devices.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.113.1.6 |
deviceLedsPowerOn1BlinkingThis status corresponds to 'on' LED on some devices.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.113.1.7 |
deviceLedsPowerOn2ColorAlternative power input LED.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.113.1.8 |
deviceLedsPowerOn2BlinkingAlternative power input LED.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.113.1.9 |
deviceLedsRing1ColorThis LED is used when ring protection is enabled.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.113.1.10 |
deviceLedsRing1BlinkingThis LED is used when ring protection is enabled.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.113.1.11 |
deviceLedsRing2ColorThis LED is used when ring protection is enabled.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.113.1.12 |
deviceLedsRing2BlinkingThis LED is used when ring protection is enabled.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.113.1.13 |
deviceLedsSignalIn1ColorIndicates status of alarm input 1.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.113.1.14 |
deviceLedsSignalIn1BlinkingIndicates status of alarm input 1.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.113.1.15 |
deviceLedsSignalIn2ColorIndicates status of alarm input 2.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.113.1.16 |
deviceLedsSignalIn2BlinkingIndicates status of alarm input 2.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.113.1.17 |
deviceLedsSignalOut1ColorIndicates status of alarm relay output 1.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.113.1.18 |
deviceLedsSignalOut1BlinkingIndicates status of alarm relay output 1.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.113.1.19 |
deviceLedsSignalOut2ColorIndicates status of alarm relay output 2.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.113.1.20 |
deviceLedsSignalOut2BlinkingIndicates status of alarm relay output 2.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.113.1.21 |
cableTestStatusTableThis table display the result of the last cable test. Values are only available for copper ports while a link is down and if the cable test function is enabled. SEQUENCE OF CableTestStatusEntry .1.3.6.1.4.1.3181.10.6.1.31.114 |
cableTestStatusEntry CableTestStatusEntry .1.3.6.1.4.1.3181.10.6.1.31.114.1 |
cableTestStatusPortIndexAutomatically generated INTEGER .1.3.6.1.4.1.3181.10.6.1.31.114.1.1 |
cableTestStatusUpdateTimeStampIndicates the time when this record was last updated.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3181.10.6.1.31.114.1.2 |
cableTestStatusPair0StateIndicates line termination test results for wire pair 0 (Pins 1/2)ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.114.1.3 |
cableTestStatusPair0DistanceToFaultDistance to fault on wire pair 0 in centimeters. Indicates 0 when no fault is detected or the function is unused.ro Integer32 .1.3.6.1.4.1.3181.10.6.1.31.114.1.4 |
cableTestStatusPair1StateIndicates line termination test results for wire pair 1 (Pins 3/6)ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.114.1.5 |
cableTestStatusPair1DistanceToFaultDistance to fault on wire pair 1 in centimeters. Indicates 0 when no fault is detected or the function is unused.ro Integer32 .1.3.6.1.4.1.3181.10.6.1.31.114.1.6 |
cableTestStatusPair2StateIndicates line termination test results for wire pair 2 (Pins 4/5)ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.114.1.7 |
cableTestStatusPair2DistanceToFaultDistance to fault on wire pair 2 in centimeters. Indicates 0 when no fault is detected or the function is unused.ro Integer32 .1.3.6.1.4.1.3181.10.6.1.31.114.1.8 |
cableTestStatusPair3StateIndicates line termination test results for wire pair 3 (Pins 7/8)ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.114.1.9 |
cableTestStatusPair3DistanceToFaultDistance to fault on wire pair 3 in centimeters. Indicates 0 when no fault is detected or the function is unused.ro Integer32 .1.3.6.1.4.1.3181.10.6.1.31.114.1.10 |
cableTestStatusCableStatusro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.114.1.11 |
ioSignalStatusTableThis section is only used for devices which offer external signal inputs and outputs. SEQUENCE OF IoSignalStatusEntry .1.3.6.1.4.1.3181.10.6.1.31.115 |
ioSignalStatusEntry IoSignalStatusEntry .1.3.6.1.4.1.3181.10.6.1.31.115.1 |
ioSignalStatusIndexAutomatically generated INTEGER (0) .1.3.6.1.4.1.3181.10.6.1.31.115.1.1 |
ioSignalStatusInput1AlarmActiveIndicates true when the input 1 is logically active.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.115.1.2 |
ioSignalStatusInput2AlarmActiveIndicates true when the input 2 is logically active.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.115.1.3 |
ioSignalStatusOutput1RelayActiveIndicates true when the output 1 relay is activated.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.115.1.4 |
ioSignalStatusOutput2RelayActiveIndicates true when the output 2 relay is activated.ro Enumeration .1.3.6.1.4.1.3181.10.6.1.31.115.1.5 |
tcamStatusTableThis section is only used for devices which offer external signal inputs and outputs. SEQUENCE OF TcamStatusEntry .1.3.6.1.4.1.3181.10.6.1.31.116 |
tcamStatusEntry TcamStatusEntry .1.3.6.1.4.1.3181.10.6.1.31.116.1 |
tcamStatusIndexAutomatically generated INTEGER .1.3.6.1.4.1.3181.10.6.1.31.116.1.1 |
tcamStatusControlFileReflects the name of the control file associated with this tcam entry.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3181.10.6.1.31.116.1.2 |
tcamStatusDescriptionDescriptive text what explains what this tcam entry will do.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3181.10.6.1.31.116.1.3 |
More MIBs from Microsens
Browse all MicrosensMIBs →MS-SWITCH30-MIB
The MS-SWITCH30-MIB module provides SNMP-based management capabilities for Microsoft Switch 30 series hardware, enabling the monitoring of interface status, port statistics, and device operational parameters.
453 objects→
MICROSENS-CWDM8-MIB
Standard SNMP MIB module defining data structures for MICROSENS-CWDM8-MIB.
113 objects→
RING-MIB
The RING-MIB module facilitates the monitoring and management of Coriolis ring network topologies, specifically tracking ring port states, topology changes, and loop prevention mechanisms within Coriolis switching hardware.
103 objects→
G6-RING-MIB
The G6-RING-MIB facilitates the monitoring and management of Generation 6 Microsens Ethernet switches, specifically enabling the tracking of ring topology status, port states, and redundancy protocol events to ensure network resilience.
87 objects→
G6-WIFI-MIB
The G6-WIFI-MIB module provides vendor-specific SNMP extensions for Microsens Generation 6 Ethernet Switches to monitor Wi-Fi interface states, client association counts, signal strength metrics, and radio channel utilization. This private MIB enables granular visibility into wireless subsystem performance and connectivity anomalies on Microsens hardware that are not covered by standard IETF MIBs.
53 objects→
G6-PORT-MIB
The G6-PORT-MIB provides vendor-specific SNMP management interfaces for Microsens Generation 6 Ethernet switches, enabling the monitoring of physical port states, traffic counters, and link layer statistics. This private MIB extension facilitates granular visibility into interface performance and connectivity status for network operations and troubleshooting on Microsens hardware.
46 objects→