RFC1406Ext-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
20
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
20 total| Object Name |
|---|
RFC1155-SMIUsed to determine current MIB module release supported
by the agent. Object is in decimal.ro INTEGER .1.3.6.1.4.1.495.2.1.6.53.1 |
dsx1ExtCfgTableThe T1/E1 extensions configuration table. SEQUENCE OF Dsx1ExtCfgEntry .1.3.6.1.4.1.495.2.1.6.53.10 |
dsx1ExtCfgEntryAn entry in the T1/E1 extensions configuration table. Dsx1ExtCfgEntry .1.3.6.1.4.1.495.2.1.6.53.10.1 |
dsx1ExtCfgLinkIndexIdentifies the physical port with the T1/E1 (dsx1Ext) interface.
Range of Values: 1 - 2
Default Value: None
Configuration Changed: administrativero INTEGER .1.3.6.1.4.1.495.2.1.6.53.10.1.1 |
dsx1ExtCfgPortStatusIndicates whether this T1/E1 (dsx1Ext) port is enabled or
disabled.
Options:
disabled (1): The port is physically present but will be
disabled (deactivated) after the next reset.
enabled (2): The port will become enabled (functional) after
the next reset.
Default Value: disabled (1)
Configuration Changed: administrativerw Enumeration .1.3.6.1.4.1.495.2.1.6.53.10.1.10 |
dsx1ExtCfgTrapsDetermines whether the software will produce a T1/E1 (dsx1...)
trap.
Options:
disabled (1): The trap will not be produced.
enabled (2): The trap will be generated.
Default Value: disabled (1)
Configuration Changed: administrativerw Enumeration .1.3.6.1.4.1.495.2.1.6.53.10.1.11 |
dsx1ExtCfgLineBuildOutSpecifies the attenuation or Line Build Out to be used
on the transmitter side of the line.
Options:
For T1
1: 0 to 133 feet / 0 dB
2: 133 to 266 feet
3: 266 to 399 feet
4: 399 to 533 feet
5: 533 to 655 feet
6: -7.5 dB
7: -15 dB
8: -22.5 dB
For E1
1: 75 Ohm (coax. cable)
2: 120 Ohm (RJ45 shilded twisted pair)
3: 75 Ohm ( with protection resistor)
4: 120 Ohm ( with protection resistor)
5: 75 Ohm (with high return loss 1:1.15)
6: 120 Ohm (with high return loss 1:1.36)
7: 75 Ohm (with high return loss 1:1.36)
8: N/A
Default Value: 1
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.53.10.1.12 |
dsx1ExtCfgCardTypeIndicates the type of card connected to this CPU board.
Options:
dsx1ExtNoCard (1): Indicates that there is not a T1 or E1 card
connected to the line interface or the value indicates that if
there is a T1 or E1 card connected then the card is not
functional.
dsx1ExtT1Card (2): Indicates that a functional T1 card is connected
to the line interface.
dsx1ExtE1Card (3): Indicates that a functional E1 card is connected
to the line interface.ro Enumeration .1.3.6.1.4.1.495.2.1.6.53.10.1.50 |
dsx1ExtCfgLossTxClockIndicates the total time at which the transmit clock was
lost on this line interface. If no such event has occurred since
system startup, then the value will be zero.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.495.2.1.6.53.10.1.51 |
dsx1ExtCfgLossSyncIndicates the total time at which the synchronization was
lost on this line interface. If no such event has occurred since
system startup, then the value will be zero.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.495.2.1.6.53.10.1.52 |
dsx1ExtCfgLossCarrierIndicates the total time at which the carrier was lost
on this line interface. If no such event has occurred since
system startup, then the value will be zero.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.495.2.1.6.53.10.1.53 |
dsx1ExtCfgT18ZeroDetectIndicates the total time that 8 consecutive zeros were received on
this line interface. If no such event has occurred since system startup,
then the value will be zero.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.495.2.1.6.53.10.1.54 |
dsx1ExtCfgT116ZeroDetectIndicates the total time that 16 consecutive zeros were
received on this line interface. If no such event has occurred
since system startup, then the value will be zero.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.495.2.1.6.53.10.1.55 |
dsx1ExtCfgT1RxB8ZSCodeIndicates the total time that a B8ZS code word was
detected during reception on this line interface. If no such
event has occurred since system startup, then the value will be
zero.
Note: B8ZS code work detection occurs whether or not the B8ZS
mode is selected.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.495.2.1.6.53.10.1.56 |
dsx1ExtCfgT1RxBlueAlarmIndicates the total time that a 'blue alarm' was received
on this line interface. A blue alarm is an unframed signal
comprised of all ones (1s). If no such event has occurred
since system startup, then the value will be zero.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.495.2.1.6.53.10.1.57 |
dsx1ExtCfgT1RxYellowAlarmIndicates the total time that a 'yellow alarm' was
received on this line interface. A yellow alarm occurs when bit
2 of 256 consecutive channels is set to zero for at least 254
occurrences in D4 format mode or when 16 consecutive patterns of
00FF hex appear in FDL format mode. If no such event has occurred
since system startup, then the value will be zero.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.495.2.1.6.53.10.1.58 |
dsx1ExtCfgIoRegTestIndicates the test results for the T1/E1 I/O card registers.ro Enumeration .1.3.6.1.4.1.495.2.1.6.53.10.1.59 |
dsx1ExtCfgSctRegTestIndicates the test results for the T1 transceiver registers,
specifically the 12 Transmit Signaling Registers.ro Enumeration .1.3.6.1.4.1.495.2.1.6.53.10.1.60 |
dsx1ExtCfgSctLatchRegTestIndicates the test results for the T1 transceiver latch register,
specifically the second Status Register.ro Enumeration .1.3.6.1.4.1.495.2.1.6.53.10.1.61 |
dsx1ExtCfgReinitWhen this object is set to any value, it reinitializes the
corresponding port.rw INTEGER .1.3.6.1.4.1.495.2.1.6.53.10.1.81 |