CXX25-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
216
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
216 total| Object Name |
|---|
x25SapAlarmFor future use. Identifies the x25SapStatusEvent trap which has occurred.
This trap is only generated when global object x25Alarms is set to value
'enabled'.
Options:
x25SapNumber: The services access point this trap applies to.
x25SapCes: The CES this trap applies to.
x25SapStatusEvent: The event which triggered the trap (see object
x25SapStatusEvent). TRAP-TYPE .1.3.6.1.4.1.495.2.1.6.29.0.1 |
x25ConfigErrorIndicationFor future use. Identifies the x25ConfigErrorEvent trap which has
occurred. This trap can always be generated.
Options:
x25SapNumber: The services access point this trap applies to. x25SapCes:
The CES this trap applies to.
x25ConfigErrorEvent: The event which triggered the trap (see object
x25ConfigErrorEvent). TRAP-TYPE .1.3.6.1.4.1.495.2.1.6.29.0.2 |
RFC1155-SMIDetermines the minimum amount of system resources which are required by
the X.25 layer. When system resources drop below this threshold, the X.25
layer clears any virtual circuits for which data activity is detected.
The value of this object must not be greater than the value of object
x25UpperPoolThreshold.
Range of Values: 1 - 99
Default Value: 30 (30 percent)
Related Objects:
x25UpperPoolThreshold
x25SapFlowControlState
x25SapFlowControlTimer
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.1 |
x25UpperPoolThresholdDetermines the amount of system resources which are required by the X.25
layer to avoid congestion. When system resources drop below this
threshold, the X.25 layer does the following:
- prohibits new virtual circuits from being established on any SAP
(service access point)
- initiates flow control on all existing virtual circuits receiving data
(an RNR is transmitted on each circuit)
When global resources rise above this threshold after having dropped below
it, the X.25 layer does the following:
- it disables flow control on all suspended virtual circuits (transmits a
RR on each circuit that that it previously transmitted an RNR on)
- permits new virtual circuits to be established
The value of this object must not be less than the value of object
x25LowerPoolThreshold.
Range of Values: 1 - 99
Default Value: 40 (40 percent)
Related Objects:
x25LowerPoolThreshold
x25SapFlowControlTimer
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.2 |
x25RouteMaskDetermines the number of digits to use for routing calls. If set to value
'0', calls are routed normally, according to the called address specified.
A value greater than '0' indicates how many called address digits are used
to scan the route table. Any call received with a called address
containing less or more digits than specified for this object is refused.
Range of Values: 0 - 15
Default Value: 0
Related Objects:
x25SapRouteDirection
x25RouteTable
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.3 |
x25BillingSegmentSizeDetermines the size of billing data segments.
Range of Values: 16 - 1024 bytes
Default Value: 16 bytes
Related Objects:
x25Billing
x25SapPvcBillingTimer
x25SapSbscrChargingInformation
x25SapSbscrNetworkUserId
x25PvcBilling
x25PvcSrcAddress
x25PvcDstAddress
x25BillingIndication
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.4 |
x25BillingDetermines if this layer generates the x25BillingIndication trap. For
switched virtual circuits the trap is generated each time a call is
cleared. For permanent virtual circuits the trap is generated each time
the x25SapPvcBillingTimer expires.
Options:
disabled (1): This layer does not generate the x25BillingIndication trap.
enabled (2): This layer generates the x25BillingIndication trap.
Default Value: disabled (1)
Related Objects:
x25BillingSegmentSize
x25SapPvcBillingTimer
x25SapSbscrChargingInformation
x25SapSbscrNetworkUserId
x25PvcBilling
x25PvcSrcAddress
x25PvcDstAddress
x25BillingIndication
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.5 |
x25NetworkTypeDetermines the format of the cause codes the X.25 layer adds to Reset,
Restart, and Clear packets.
Note: The X.25 layer will not generate Diagnostics packets for any SAP
when configured with value 'dteEndpoint'.
Options:
publicDataNetwork (1): Standard cause codes are generated.
privateDataNetwork (2): Cause codes have the most significant bit set.
dteEndpoint (3): Cause codes (with most significant bit set) are only
generated for SAPs configured as DCEs, and are set to 0 for SAPs
configured as DTEs.
Related Objects:
x25SapInterfaceType
Default Value: dteEndpoint (3)
Configuration Changed: administrativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.6 |
x25HuntGroupRotationDetermines if hunt group members are rotated. Enabling rotation causes
hunting to begin with a different hunt group member each time. For
example, a group with three members would be hunted as follows: 123, 231,
312, 123.
Group members are rotated after each use or after detection of a member
which is unavailable.
Options:
disabled (1): Hunt group members are not rotated.
enabled (2):. Hunt group members are rotated.
Default Value: disabled (1)
Related Objects:
x25HuntGroupTable
Configuration Changed: administrativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.7 |
x25AlarmsFor future use. Determines if this layer generates the x25SapAlarm trap.
Options:
disabled (1): This layer does not generate the x25SapAlarm trap.
enabled (2): This layer generates the x25SapAlarm trap.
Default Value: disabled (1)
Related Objects:
x25SapStatusEvent
x25SapAlarm
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.10 |
x25SapStatusEventFor future use. Indicates the status reported by an x25SapAlarm trap when
it occurs. This object always returns the value 'noEvent' when read.
Options:
noEvent (1): There is no status to report.
Related Objects:
x25Alarms
x25SapStatusEventro Enumeration .1.3.6.1.4.1.495.2.1.6.29.11 |
x25ConfigErrorEventFor future use. Indicates the status reported by an
x25ConfigErrorIndication trap when it occurs. This object always returns
the value 'noEvent' when read.
Options:
noEvent (1): There is no error event to report.
Related Objects:
x25ConfigErrorIndicationro Enumeration .1.3.6.1.4.1.495.2.1.6.29.12 |
x25SoftwareVersionsIdentifies the X.25 software revision number, which is displayed as a
string of five numbers each separated by a period (1.2.3.4.5). The five
numbers represent:
- (1) main version number
- (2) main revision number
- (3) branch version number
- (4) branch revision number
- (5) part numberro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.495.2.1.6.29.19 |
x25LogicalLinkTableA logical link is a group of one or more lower service access
points(SAPs) created for the purpose of route balancing. Two types of
route balancing algorithms are supported: prioritized or balanced.
In order to use a logical link group for routing, one or more route table
entries must be created that refer to the group.
Members of a logical link group are uniquely identified by two values: SAP
Number and CES. SEQUENCE OF X25LogicalLinkEntry .1.3.6.1.4.1.495.2.1.6.29.20 |
x25LogicalLinkEntryDefines a row in the x25LogicalLinkTable. Each row contains the objects
which are used to define a member of a logical link. X25LogicalLinkEntry .1.3.6.1.4.1.495.2.1.6.29.20.1 |
x25LLNumberIdentifies the logical link entry with a unique numerical value.ro SapIndex .1.3.6.1.4.1.495.2.1.6.29.20.1.1 |
x25LLSapNumberDetermines the lower X.25 layer SAP (service access point) this logical
link is associated with. This is the first half of the SAP identification.
The second half is specified by object x25LLSapCes.
Only lower SAPs can be part of a logical link.
Range of Values: 1 - 255
Configuration Changed: administrativerw SapIndex .1.3.6.1.4.1.495.2.1.6.29.20.1.2 |
x25LLSapCesDetermines the CES (connection endpoint suffix) this logical link is
associated with. CES is used by X.25 over the ISDN D channel to support
multiple data links on one physical (LAPD) link. The CES for each link
must be unique and is normally set in the range 0 to 63.
In the case of X.25 LAPB, CES is not used and is set to 0.
Range of Values: 1 - 63
Default Value: none
Configuration Changed: administrativerw Ces .1.3.6.1.4.1.495.2.1.6.29.20.1.3 |
x25LLRowStatusDetermines the status of the objects in a table row.
Options:
invalid (1): Row is deleted from the table immediately, however values are
still in effect until the next reset.
valid (2): Use this value to add a new row to the table, or modify an
existing row.
Configuration Changed: administrativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.20.1.4 |
x25LLRouteAlgorithmDetermines the algorithm used by this logical link to choose the member
to route a call to. The value set for the first member of a logical group
(lowest SAP/CES combination) overrides the settings for all other members
of the group. Therefore, if you want to change the route algorithm for a
group you need to alter the settings of the first member only.
Options:
balanced (1): Members are chosen in round-robin fashion.
prioritized (2): The first member is always chosen for routing. The second
is chosen if the first is not available (disconnected or congested). The
third is chosen if the first and the second are not available, etc.
Default Value: prioritized (2)
Related Objects:
x25LLSapNumber
x25LLSapCes
Configuration Changed: administrativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.20.1.5 |
x25LLEntryStateIndicates the state of this logical link.
Options:
offLine (1): This logical link is configured.
onLine (2): This logical link is not configured.ro Enumeration .1.3.6.1.4.1.495.2.1.6.29.20.1.6 |
x25SapTableThe SAP table contains configuration information for each X.25 layer SAP
(service access point).
Service Access Points
Two types of SAPs exist:
- Upper: A SAP that exists at the upper interface of the X.25 layer and
serves an embedded application.
- Lower: A SAP that exists at the lower interface of the X.25 layer and
serves a single data link connection (LAPB) or multiple data link
connections (LAPD).
This data link connection, when attached to the sub-layer, can complete a
LAPB service, or can be one of many supported data link connections over a
LAPD service.
SAPs are identified by a SAP Number and CES (connection endpoint suffix).
X.25 LAPB service supports only one data link connection and thus only one
SAP is required. Its CES is irrelevant and is normally set to 0 at this
SAP. This SAP communicates with its 'companion' SAP at the sub-layer in a
one-to-one relationship.
X.25 LAPD service supports multiple data link connections, and thus
multiple SAPs are required. The CES for each must be unique and is
normally in the range of 0 to 63. Each of these SAPs (which are grouped
according to SAP Number) communicate with the same 'companion' SAP at the
sub-layer in a many-to-one relationship.
Facilities
This table contains numerous facilities subscription parameters. Each
facility subscription that is part of the standard, is referenced to the
appropriate section in the ITU(CCITT) X.25 (1988) blue book in the
REFERENCE section of the object.
Terms used in this table
Incoming calls: For lower SAPs, these are the X.25 calls received from the
sub-layer. For upper SAPs, these are the X.25 calls received from the
associated application.
Outgoing calls: Are the X.25 calls routed from other SAPs, which are to go
out this SAP.
Source side: The side that received an incoming call.
Destination side: The side that will send the outgoing call. SEQUENCE OF X25SapEntry .1.3.6.1.4.1.495.2.1.6.29.21 |
x25SapEntryDefines a row in the x25SapTable. Each row contains the objects which
define a service access point. X25SapEntry .1.3.6.1.4.1.495.2.1.6.29.21.1 |
x25SapNumberIdentifies this SAP (service access point) with a numerical value. This
is the first half of the SAP identifier. The second half is specified by
object x25SapCes. The full SAP identification must uniquely identify a SAP
which exists within the X.25 layer.
Range of Values: 1 - 255
Default Value: none
Related Objects:
x25SapCes
Configuration Changed: administrativero SapIndex .1.3.6.1.4.1.495.2.1.6.29.21.1.1 |
x25SapCesIdentifies the CES (connection endpoint suffix) that is associated with
this SAP (service access point). CES is used by X.25 over the ISDN D
channel to support multiple data links on one physical (LAPD) link. The
CES for each link must be unique and is normally set in the range 0 to 63.
When associated with a LAPD service at the Data Link layer, the CES is
combined with the data link SAPI (sap identification index) to form the
connection endpoint identifier (CEI). This uniquely identifies each data
link connection. The Data Link layer maps the CES to a TEI (terminal
endpoint identifier), and combines it with the SAPI to form the DLCI (data
link connection identifier), which is used on the ISDN D-Channel.
In the case of X.25 LAPB, CES is not used and is set to 0.
When this object is not specified (upper SAPs), its value defaults to 0.
Range of Values: 0 - 63
Default Value: none
Related Objects:
x25SapNumber
Configuration Changed: administrativero Ces .1.3.6.1.4.1.495.2.1.6.29.21.1.2 |
x25SapRowStatusDetermines the status of the objects in a table row.
Options:
invalid (1): Row is deleted from the table immediately, however values are
still in effect until the next reset.
valid (2): Use this value to add a new row to the table, or modify an
existing row.
Default Value: none
Configuration Changed: administrativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.3 |
x25SapTypeSpecifies this SAP (service access point) as either 'upper' or 'lower'.
Options:
lower (1): This is a lower SAP.
upper (2): This is an upper SAP.
Default Value: lower (1)
Configuration Changed: administrativerw SapType .1.3.6.1.4.1.495.2.1.6.29.21.1.4 |
x25SapAliasIdentifies this service access point by a textual name. Names must be
unique across all service access points at all layers.
Range of Values: 1 -16 alphanumeric characters (first character must be a
letter)
Default Value: none
Configuration Changed: administrativerw Alias .1.3.6.1.4.1.495.2.1.6.29.21.1.5 |
x25SapCompanionAliasThis object applies only to lower SAPs (service access points).
Determines the sub-layer SAP this SAP communicates with. This object
contains the textual name of the sub- layer SAP. All service access points
whose CES share the same SAP number (as specified by object x25SapNumber)
must specify the same companion alias.
Range of Values: 1 -16 alphanumeric characters (first character must be a
letter)
Related Objects:
x25SapNumber
Default Value: none
Configuration Changed: administrativerw Alias .1.3.6.1.4.1.495.2.1.6.29.21.1.6 |
x25SapInterfaceTypeThis object applies only to lower SAPs (service access points).
Determines the SAP interface type. This is used to determine the how cause
codes are generated, and how facility subscriptions are handled.
Options:
dte (1): This SAP communicates with an external X.25 DCE.
dce (2): This SAP communicates with an external X.25 DTE.
Default Value: dte (1)
Configuration Changed: administrativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.13 |
x25SapLinkTypeThis object applies only to lower SAPs (service access points).
Determines the type of service provided by this SAP.
Options:
x25Link (1): This SAP provides support for the X.25 protocol.
x75Link (2): This SAP provides support for the X.75 protocol. (For future
use.)
Default Value: x25Link (1)
Configuration Changed: administrativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.14 |
x25SapRoutePartitionDetermines the route table partition used to route incoming calls.
Default Value: 0
Related Objects:
x25RouteTable
Configuration Changed: administrative and operativerw RoutePartition .1.3.6.1.4.1.495.2.1.6.29.21.1.19 |
x25SapRouteDirectionThis object applies only to lower SAPs (service access points).
Determines the direction for the routing of incoming calls.
Options:
both (1): Permits calls to be routed to both upper and lower SAPs.
upper (2): Restricts the routing of calls to upper SAPs only.
lower (3): Restricts the routing of calls to other lower SAPs only.
Default Value: both (1)
Related Objects:
x25RouteMask
x25RouteTable
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.20 |
x25SapWildCardRoutingDetermines if this SAP applies a routing mask to the called address in
incoming calls prior to routing. This implies that certain called address
digits may be masked out prior to searching the route table. The mask is
specified by object x25SapWildCardRoutingMask.
Options:
false (1):No mask is applied to incoming calls prior to routing.
true (2): A mask is applied to the called address in incoming calls prior
to routing.
Default Value: false (1)
Related Objects:
x25RouteMask
x25SapRouteDirection
x25SapWildCardRoutingMask
x25RouteTable
Configuration Changed: administrative and operativerwobsolete Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.21 |
x25SapWildCardRoutingMaskDetermines the route mask, which is applied to the called address in
incoming calls prior to routing. The route mask is a bit mask, with each
bit directly mapped to the corresponding digit in the X.25 called address,
starting with the least significant bit (bit 1) and ending with the most
significant bit (bit 15.)
Turning a mask bit on (setting it to 1), means the corresponding digit in
the X.25 address is used during routing. Turning a mask bit off (setting
it to 0), means the corresponding digit is ignored during routing.
Range of Values: 0 - 32767
Default Value: 0
Related Objects:
x25SapWildCardRouting
Configuration Changed: administrative and operativerwobsolete INTEGER .1.3.6.1.4.1.495.2.1.6.29.21.1.22 |
x25SapActivationThis object applies only to lower SAPs (service access points).
Determines the type of data link activation used by this SAP. These are
internal commands exchanged between X.25 and the sub-layer.
Options:
normal (1): Forces this SAP to attempt a connection to the sub-layer
immediately following a system reset, and periodically thereafter until
confirmed.
dynamic (2): Forces this SAP to attempt a connection to the sub-layer only
when an outgoing call is routed through this SAP. Subsequently forces this
SAP to disconnect from the sub-layer following the clearing of the last
existing call routed through this SAP.
dynamic-30s-delay (3): Forces this SAP to attempt a connection to the sub-layer
only when an outgoing call is routed through this SAP. Subsequently forces this
SAP to delay disconnect from the sub-layer following the clearing of the last
existing call routed through this SAP until either a new call is received, or
30 seconds have elapsed, whichever comes first.
dynamic-60s-delay (4): Forces this SAP to attempt a connection to the sub-layer
only when an outgoing call is routed through this SAP. Subsequently forces this
SAP to delay disconnect from the sub-layer following the clearing of the last
existing call routed through this SAP until either a new call is received, or
60 seconds have elapsed, whichever comes first.
dynamic-90s-delay (5): Forces this SAP to attempt a connection to the sub-layer
only when an outgoing call is routed through this SAP. Subsequently forces this
SAP to delay disconnect from the sub-layer following the clearing of the last
existing call routed through this SAP until either a new call is received, or
90 seconds have elapsed, whichever comes first.
dynamic-120s-delay (6): Forces this SAP to attempt a connection to the sub-layer
only when an outgoing call is routed through this SAP. Subsequently forces this
SAP to delay disconnect from the sub-layer following the clearing of the last
existing call routed through this SAP until either a new call is received, or
120 seconds have elapsed, whichever comes first.
Default Value: normal
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.26 |
x25SapPvcBillingTimerFor future use. This object applies only to lower SAPs (service access
points).
Determines the period between generation of billing information for all
configured PVCs (permanent virtual circuits) at this SAP. A value of '0'
indicates no billing information is generated.
Range of Values: 0 - 300 seconds
Default Value: 0 (no billing)
Related Objects:
x25BillingSegmentSize
x25Billing
x25SapSbscrChargingInformation
x25SapSbscrNetworkUserId
x25PvcBilling
x25PvcSrcAddress
x25PvcDstAddress
x25BillingIndication
Configuration Changed: administrative and operativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.21.1.27 |
x25SapModuloThis object applies only to lower SAPs (service access points).
Determines the range of sequence numbers available for packet numbering at
this SAP (service access point). The modulo specified for this object must
match that specified on the destination SAP for a route to be successful.
If not, this SAP will refuse the call.
Options:
modulo8 (1): Sequence numbers range from 0 to 7, supporting a maximum
window size of 8.
modulo128 (2): Sequence numbers range from 0 to 128, supporting a maximum
window size of 128
Default Value: modulo8 (1)
Related Objects:
x25SapRxWindowSize
x25SapTxWindowSize
x25PvcRxWindow
x25PvcTxWindow
Configuration Changed: administrativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.31 |
x25SapRxPacketSizeDetermines the default receive packet size used by this SAP. This value
is used only when flow control negotiation
(x25SapSbscrFlowCntrlParamNegotiation) is not subscribed to, or when a
D-bit call is routed through this SAP.
Options:
bytes16 (4)
bytes32 (5)
bytes64 (6)
bytes128 (7)
bytes256 (8)
bytes512 (9)
bytes1024 (10)
bytes2048 (11)
bytes4096 (12)
Default Value: bytes128 (7)
Related Objects:
x25SapSbscrFlowCntrlParamNegotiation
Configuration Changed: administrative and operativerw PacketSize .1.3.6.1.4.1.495.2.1.6.29.21.1.32 |
x25SapTxPacketSizeDetermines the default transmit packet size used by this SAP. This value
is used only when flow control negotiation
(x25SapSbscrFlowCntrlParamNegotiation) is not subscribed to, or when a
D-bit call is routed through this SAP.
Options:
bytes16 (4)
bytes32 (5)
bytes64 (6)
bytes128 (7)
bytes256 (8)
bytes512 (9)
bytes1024 (10)
bytes2048 (11)
bytes4096 (12)
Default Value: bytes128 (7)
Related Objects:
x25SapSbscrFlowCntrlParamNegotiation
Configuration Changed: administrative and operativerw PacketSize .1.3.6.1.4.1.495.2.1.6.29.21.1.33 |
x25SapRxWindowSizeDetermines the default receive window size used by this SAP. This value
is used only when flow control negotiation
(x25SapSbscrFlowCntrlParamNegotiation) is not subscribed to, or when a
D-bit call is routed through this SAP.
Range of Values: 1 - 7 for modulo 8
1 - 127 for modulo 128
Default Value: 2
Related Objects:
x25SapSbscrFlowCntrlParamNegotiation
x25SapModulo
Configuration Changed: administrative and operativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.21.1.34 |
x25SapTxWindowSizeDetermines the default transmit window size used by this SAP. This value
is used only when flow control negotiation
(x25SapSbscrFlowCntrlParamNegotiation) is not subscribed to, or when a
D-bit call is routed through this SAP.
Range of Values: 1 - 7 for modulo 8
1 - 127 for modulo 128
Default Value: 2
Related Objects:
x25SapSbscrFlowCntrlParamNegotiation
x25SapModulo
Configuration Changed: administrative and operativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.21.1.35 |
x25SapRxThruputClassDetermines the default receive throughput class used by this SAP. This
value is used only when throughput class negotiation
(x25SapSbscrThruputClassNegotiation) is not subscribed to, or when a D-bit
call is routed through this SAP.
Options:
bps75 (3)
bps150 (4)
bps300 (5)
bps600 (6)
bps1200 (7)
bps2400 (8)
bps4800 (9)
bps9600 (10)
bps19200 (11)
bps48000 (12)
bps64000 (13)
Default Value: bps9600 (10)
Related Objects:
x25SapTxThruputClass
x25SapSbscrThruputClassNegotiation
Configuration Changed: administrative and operativerw ThruputClass .1.3.6.1.4.1.495.2.1.6.29.21.1.36 |
x25SapTxThruputClassDetermines the default transmit throughput class used by this SAP. This
value is used only when throughput class negotiation
(x25SapSbscrThruputClassNegotiation) is not subscribed to, or when a D-bit
call is routed through this SAP.
Options:
bps75 (3)
bps150 (4)
bps300 (5)
bps600 (6)
bps1200 (7)
bps2400 (8)
bps4800 (9)
bps9600 (10)
bps19200 (11)
bps48000 (12)
bps64000 (13)
Default Value: bps9600 (10)
Related Objects:
x25SapRxThruputClass
x25SapSbscrThruputClassNegotiation
Configuration Changed: administrative and operativerw ThruputClass .1.3.6.1.4.1.495.2.1.6.29.21.1.37 |
x25SapRxWindowThresholdThis object applies only to lower SAPs (service access points).
Determines the threshold at which this lower SAP is forced to close its
receive window (issue RNRs). This threshold is only effective if set as
follows:
- if no receive window negotiation has taken place during the call
establishment phase, the threshold is effective if configured to less than
the value for object x25SapRxWindowSize.
- if the receive window has been negotiated to a value other than its
default, as specified by object x25SapRxWindowSize, the threshold is only
effective if configured less than the negotiated value.
Range of Values: 1 - 7 for modulo 8
1 - 127 for modulo 128
Default Value: 7
Related Objects:
x25SapSbscrFlowCntrlParamNegotiation
x25SapModulo
x25SapRxWindowSize
Configuration Changed: administrative and operativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.21.1.38 |
x25SapLcnAllocationDetermines the order in which logical channel numbers (LCNs) are assigned
by this SAP (service access point).
Options:
ascending (1): LCNs are assigned in ascending order.
descending: (2): LCNs are assigned in descending order.
Default Value: descending (2)
Configuration Changed: administrativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.48 |
x25SapLpvcLcnDetermines the lowest LCN (logical channel number) for permanent virtual
circuits established at this SAP.
Range of Values: 0 - 1023
Default Value: 0
Related Objects:
x25SapHpvcLcn
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.21.1.49 |
x25SapHpvcLcnDetermines the highest LCN (logical channel number) for permanent virtual
circuits established at this SAP. This value must be greater than
x25SapLpvcLcn and less than x25SapLicLcn.
Range of Values: 0 - 1023
Default Value: 0
Related Objects:
x25SapLpvcLcn
x25SapLicLcn
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.21.1.50 |
x25SapLicLcnThis object applies only to lower SAPs (service access points).
Determines the lowest LCN (logical channel number) for incoming virtual
circuits at this SAP. This value must be greater than x25SapHpvcLcn and
less than x25SapHicLcn.
Range of Values: 0 - 1023
Default Value: 0
Related Objects:
x25SapHpvcLcn
x25SapHicLcn
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.21.1.51 |
x25SapHicLcnThis object applies only to lower SAPs (service access points).
Determines the highest LCN (logical channel number) for incoming virtual
circuits at this SAP. This value must be greater than x25SapLicLcn and
less than x25SapLtcLcn.
Range of Values: 0 - 1023
Default Value: 0
Related Objects:
x25SapLicLcn
x25SapLtcLcn
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.21.1.52 |
x25SapLtcLcnDetermines the lowest LCN (logical channel number) for two-way virtual
circuits at this SAP. This value must be greater than x25SapHicLcn and
less than x25SapHtcLcn.
Range of Values: 0 - 1023
Default Value: 1
Related Objects:
x25SapHicLcn
x25SapHtcLcn
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.21.1.53 |
x25SapHtcLcnDetermines the lowest LCN (logical channel number) for two-way virtual
circuits at this SAP. This value must be greater than x25SapLtcLcn and
less than x25SapLocLcn.
Range of Values: 0 - 1023
Default Value: 16
Related Objects:
x25SapLtcLcn
x25SapLocLcn
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.21.1.54 |
x25SapLocLcnThis object applies only to lower SAPs (service access points).
Determines the lowest LCN (logical channel number) for two-way virtual
circuits at this SAP. This value must be greater than x25SapHtcLcn and
less than x25SapHocLcn.
Range of Values: 0 - 1023
Default Value: 0
Related Objects:
x25SapHtcLcn
x25SapHocLcn
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.21.1.55 |
x25SapHocLcnThis object applies only to lower SAPs (service access points).
Determines the highest LCN (logical channel number) for outgoing virtual
circuits at this SAP. This value must be greater than x25SapLocLcn.
Range of Values: 0 - 1023
Default Value: 0
Related Objects:
x25SapLocLcn
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.21.1.56 |
x25SapConnectTimerThis object applies only to lower SAPs (service access points).
Determines the maximum time that this SAP waits for the sub-layer
(typically the Data Link layer)to establish the physical/logical line.
Range of Values: 0 - 200 seconds
Default Value: 5 seconds
Configuration Changed: administrative and operativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.21.1.61 |
x25SapDisconnectTimerThis object applies only to lower SAPs (service access points).
Determines the maximum time that this SAP waits for the sub-layer
(typically the Data Link layer)to confirm that the physical/logical line
has been taken down as previously requested by this SAP.
Range of Values: 1 - 200 seconds
Default Value: 60 seconds
Configuration Changed: administrative and operativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.21.1.62 |
x25SapRestartTimerThis object applies only to lower SAPs (service access points).
Determines the maximum time that this SAP waits for a Restart Confirmation
packet in response to a previously sent Restart Request packet.
Range of Values: 1 - 300 seconds
Default Value: 180 seconds
Configuration Changed: administrative and operativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.21.1.63 |
x25SapCallTimerDetermines the maximum amount of time this SAP waits for a Call Connected
packet in response to a previously sent Call Request packet.
Range of Values: 1 - 300
Default Value: 200 seconds
Configuration Changed: administrative and operativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.21.1.64 |
x25SapResetTimerDetermines the maximum amount of time this SAP waits for a Reset
Confirmation packet in response to a previously sent Reset Request packet.
Range of Values: 1 - 300
Default Value: 180 seconds
Configuration Changed: administrative and operativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.21.1.65 |
x25SapClearTimerDetermines the maximum amount of time this SAP waits for a Clear
Confirmation packet in response to a previously sent Clear Request packet.
Range of Values: 1 - 300
Default Value: 180 seconds
Configuration Changed: administrative and operativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.21.1.66 |
x25SapInactivityTimerDetermines the maximum amount of time this SAP (service access point) can
hold outbound queued data for a virtual circuit. If this timer expires
before the queued data can be sent, the virtual circuit is reset (the SAP
issues a Reset Request packet). This is a global setting that applies to
all virtual circuits established at this SAP.
A value of '0' disables this timer, and is the recommended setting for
upper SAPs.
Range of Values: 0 - 300 seconds
Default Value: 60 seconds
Configuration Changed: administrative and operativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.21.1.67 |
x25SapFlowControlTimerThis object applies only to lower SAPs (service access points).
Determines the amount of time between checks of available system resources
when the virtual circuits at this SAP have entered flow control. Flow
control is initiated when system resources have fallen below the threshold
specified by object x25LowerPoolThreshold.
This timer is started when flow control is initiated, and when it expires,
system resources are rechecked. If resources have risen above
x25UpperPoolThreshold, flow control is terminated (a packet-level RR is
issued on the affected virtual circuit), otherwise the timer is restarted.
Packet level RNR/RR are only issued for virtual circuits on lower SAPs.
Virtual circuits on upper SAPs issue internal flow control messages.
This is a global setting that applies to all virtual circuits established
at this SAP.
Range of Values: 1 - 300 seconds
Default Value: 10 seconds
Related Objects:
x25LowerPoolThreshold
x25UpperPoolThreshold
Configuration Changed: administrative and operativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.21.1.68 |
x25SapWindowStatusTimerDetermines the maximum amount of time this SAP waits for an outgoing
packet to piggy-back an acknowledgment onto. If this timer expires, it
forces an acknowledgment packet to be sent. This timer is restarted each
time a packet is sent.
Range of Values: 1 - 300 seconds
Default Value: 60 seconds
Configuration Changed: administrative and operativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.21.1.69 |
x25SapSbscrCalledAddressInsertionThis object applies only to lower SAPs (service access points).
Determines if this SAP inserts the called address in Call Accept packets,
and if the called address is validated. The behavior of this facility
changes depending on the whether this SAP routes calls to an upper or
lower SAP. See the X25RouteTable for more information on routes. This
object only applies to the source SAP in a route.
Options:
false (1): Not subscribed: no action is taken.
true (2): Subscribed: When this SAP receives a Call Accepted packet that
contains a called address, it verifies the address against the called
address contained in the Incoming Call packet. If they do not match, the
call is cleared.
When this SAP receives a Call Accepted packet that does not contain a
called address, the action it takes depends on the type of route.
If routing to an upper SAP, then the called address from the Incoming Call
packet is inserted into the Call Accepted packet.
If routing to a lower SAP, no action is taken.
Default Value: true (2)
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.80 |
x25SapSbscrCallingAddressInsertionThis object applies only to lower SAPs (service access points).
Determines if this SAP inserts the calling address in Call Accept packets,
and if the calling address is validated. The behavior of this facility
changes depending on the whether this SAP routes calls to an upper or
lower SAP. See the X25RouteTable for more information on routes. This
object only applies to the source SAP in a route.
Options:
false (1): Not subscribed: no action is taken.
true (2): Subscribed: When this SAP receives a Call Accepted packet that
contains a calling address, it verifies the address against the calling
address contained in the Incoming Call packet. If they do not match, the
call is cleared.
When this SAP receives a Call Accepted packet that does not contain a
calling address, the action it takes depends on the type of route.
If routing to an upper SAP, then the calling address from the Incoming
Call packet is inserted into the Call Accepted packet.
If routing to a lower SAP, no action is taken.
Default Value: true (2)
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.81 |
x25SapSbscrPktRetransmissionThis object applies only to lower SAPs (service access points).
Determines if this SAP subscribes to the Packet Retransmission facility.
Options:
false (1): Not subscribed: This SAP does not maintain copies of
transmitted packets, and responds to packet-level Reject packets by
resetting the virtual circuit.
true (2): Subscribed: This SAP responds to Reject packets by
retransmitting all unacknowledged data packets on the affected virtual
circuit. This SAP maintains copies of each data packet transmitted across
all active virtual circuits in anticipation of Rejects. The copies are
kept until they are acknowledged.
Default Value: false (1)
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.82 |
x25SapSbscrInAccessBarredDetermines if this SAP subscribes to the Incoming Calls Barred facility.
Options:
false (1): Not subscribed.
true (2): Subscribed: If this is a lower SAP configured as DTE
(x25SapInterfaceType set to 'DTE'), it will refuse(bar) all incoming calls
from the DCE. If this is a lower SAP configured as DCE
(x25SapInterfaceType set to 'DCE'), it will refuse(bar) all outgoing calls
to the DTE.If this is an upper SAP, it will refuse(bar) all outgoing
calls.
Default Value: false (1)
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.83 |
x25SapSbscrOutAccessBarredThis object applies only to lower SAPs (service access points).
Determines if this SAP subscribes to the Outgoing Calls Barred facility.
Options:
false (1): Not subscribed.
true (2): Subscribed: If this SAP is configured as DTE
(x25SapInterfaceType set to 'DTE'), it will refuse(bar) all outgoing calls
to the DCE. If this SAP is configured as DCE (x25SapInterfaceType set to
'DCE'), it will refuse(bar) all incoming calls from the DTE.
Default Value: false (2)
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.84 |
x25SapSbscrFlowCntrlParamNegotiationThis object applies only to lower SAPs (service access points).
Determines if this SAP subscribes to the Flow Control Parameter
Negotiation facility. This allows negotiation of packet sizes and window
sizes for all incoming or outgoing calls.
Options; false (1): Not subscribed.
Incoming calls: This SAP refuses all Incoming Call and Call Connected
packets that contain the flow control facility.
Outgoing calls from upper SAPs: This SAP refuses all Call Accept packets
containing flow control facilities which originate from an upper SAP.
Outgoing calls from lower SAPs: If the lower SAP (incoming side)
subscribes to the flow control facility, then the default settings for
flow control parameters (window sizes and packet sizes) at this SAP are
used to replace the flow control facilities in the Call Request/Call
Accepted packet. If the lower SAP (incoming side) does not subscribe to
the flow control facility, then the facility settings in the Call
Request/Call Accepted packet are compared against the default flow control
parameters settings (window sizes and packet sizes) for this SAP. If equal
the packet is routed, if not the packet is refused and the call is
cleared.
true (2): Subscribed.
Incoming Calls: This SAP does not alter any flow control facilities found
in incoming Call Request and Call Accept packets.
Outgoing Calls: This SAP does not alter any flow control facilities found
in outgoing Call Request and Call Accept packets. If no flow control
facilities are found this SAP inserts its default settings into the Call
Request or Call Accept packet.
Note: An incoming/outgoing Call Request with the D-bit set implies the use
of the default packet and window sizes configured at this SAP for the
virtual circuit being connected.
Default Value: true (2)
Related Objects:
x25SapRxPacketSize
x25SapTxPacketSize
x25SapRxWindowSize
x25SapTxWindowSize
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.85 |
x25SapSbscrThruputClassNegotiationThis object applies only to lower SAPs (service access points).
Determines if this SAP subscribes to the Throughput Class Negotiation
facility. This allows negotiation of performance characteristics for all
incoming or outgoing calls.
Options; false (1): Not subscribed. This SAP refuses all Incoming Call and
Call Connected packets that contains the throughput class negotiation
facility.
true (2): Subscribed.
Incoming Calls: This SAP does not alter any throughput class facilities
found in incoming Call Request and Call Accept packets.
Outgoing Calls: This SAP may alter throughput class facilities found in
outgoing Call Request and Call Accept packets. If the outgoing packet
contain throughput facilities they are compared against the settings for
this SAP, and the lesser of the two is used. If no throughput class
facilities are found, this SAP inserts its default settings into the Call
Request or Call Accept packet.
Default Value: false (1)
Related Objects:
x25SapRxThruputClass
x25SapTxThruputClass
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.86 |
x25SapSbscrFastSelectDetermines if this SAP subscribes to the Fast Select facility. This
applies to outgoing calls only.
Options:
false (1): Not subscribed. This SAP will refuse incoming calls contained
the Fast Select facility, and will refuse incoming Call Request/Accept
packets containing a user data field larger than 16 bytes.
true (2): Subscribed: This SAP permits up to 128 bytes of user data to be
included in Call Request, Call Accept, and Clear Request packets. This SAP
routes incoming calls containing the fast select facility only if the
destination side has subscribed to the Fast Select Acceptance facility.
Default Value: true (2)
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.87 |
x25SapSbscrFastSelectAcceptanceDetermines if this SAP subscribes to the Fast Select Acceptance facility.
This applies to incoming calls only.
Options:
false (1): Not subscribed. This SAP will refuse outgoing calls containing
the Fast Select facility.
true (2): Subscribed: This SAP permits outgoing calls containing the Fast
Select facility. A call containing the fast select facility will only be
routed here if the inbound side subscribes to the fast select facility
(X25SapSbscrFastSelect).
Default Value: true (2)
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.88 |
x25SapSbscrReverseChargingAcceptanceThis object applies only to lower SAPs (service access points).
Determines if this SAP subscribes to the Reverse Charging Acceptance
facility. This facility applies to outgoing calls only.
Options:
false (1): Not subscribed. This SAP refuses outgoing calls containing the
Reverse Charging facility.
true (2): Subscribed: This SAP permits outgoing calls containing the
Reverse Charging facility.
Default Value: true (2)
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.89 |
x25SapSbscrLocalChargingPreventionThis object applies only to lower SAPs (service access points).
Determines if this SAP subscribes to the Local Charging Prevention
facility. This facility applies to incoming calls only.
Options:
false (1): Not subscribed. This SAP routes all incoming calls containing
neither the Reverse Charging nor the NUI facility.
true (2): Subscribed: If an incoming call contains neither the Reverse
Charging, nor the NUI facility, this SAP adds the Reverse Charging
facility prior to routing to the outbound side, if the outbound side has
subscribed to the Reverse Charging facility. If the outbound side has not
subscribed to the Reverse Charging facility, this SAP refuses the call.
Default Value: false (1)
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.90 |
x25SapSbscrChargingInformationDetermines if this SAP subscribes to the Charging Information facility.
This facility applies to incoming calls only.
Options:
false (1): Not subscribed. This SAP refuses all calls containing the
Charging Information facility.
true (2): Subscribed: This SAP routes incoming calls containing the
Charging Information facility. When such calls are established and later
cleared, this SAP inserts billing information about the connection within
the clear packet generated/received. This is only done if the incoming
call that established the connection also contained the Charging
Information facility and if the SAP is configured as DCE
(x25SapInterfaceType).
Default Value: false (1)
Related Objects:
x25Billing
x25SapPvcBillingTimer
x25SapSbscrNetworkUserId
x25PvcBilling
x25PvcSrcAddress
x25PvcDstAddress
x25BillingIndication
x25SapInterfaceType
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.91 |
x25SapSbscrCallRedirectionDetermines if this SAP subscribes to the Call Redirection facility. This
facility applies to outgoing calls only.
Options:
false (1): Not subscribed. This SAP does not redirect calls.
true (2): Subscribed: This SAP redirects outgoing calls to the configured
call redirection address (x25SapRedirectionAddress). Redirection takes
place only if:
- this outbound SAP is not available (lower SAPs only)
- this outbound SAP is out of available LCNs
- incoming calls are barred at this outbound SAP (configured as a DTE)
- outgoing calls are barred at this outbound SAP (configured as a DCE)
In addition, redirection can then only succeed if the inbound side has
subscribed to the Permission to Redirect facility.
Default Value: false (1)
Related Objects:
x25SapRedirectionAddress
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.92 |
x25SapSbscrPermissionToRedirectDetermines if this SAP subscribes to the Permission to Redirect facility.
This facility applies to incoming calls only.
Options:
false (1): Not subscribed. This SAP refuses incoming calls even if the
outgoing side subscribes to the Call Redirection facility and supplies a
redirection address.
true (2): Subscribed: This SAP redirects incoming calls to the redirection
address specified by the outgoing side which refused the outgoing call.
The redirection address is only supplied by an outgoing side if it
subscribes to the Call Redirection facility, and is configured with a
redirection address.
Default Value: false (1)
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.93 |
x25SapRedirectionAddressDetermines the address this SAP redirects calls to. To make use of this
address this SAP must subscribe to the Call Redirection facility.
Range of Values: DTE address enclosed in quotes (up to 15 characters in
length)
Default Value: none
Related Objects:
x25SapSbscrCallRedirection
Configuration Changed: administrative and operativerw X25Address .1.3.6.1.4.1.495.2.1.6.29.21.1.94 |
x25SapSbscrNetworkUserIdDetermines if this SAP subscribes to the Network User Indentification
(NUI) facility. This facility applies to incoming calls only.
Options:
false (1): Not subscribed. This SAP refuses all incoming calls containing
the Network User Identification facility.
true (2): Subscribed: This SAP routes incoming calls containing the NUI
facility When such calls are established and are later cleared, this SAP
inserts billing information about the connection within the Clear packet
generated/received. The charging information contains the NUI which is
used for third party billing. This is only done if the incoming call that
established the connection contained the Charging Information facility and
this facility was also subscribed to by this SAP, and this SAP is
configured as DCE (x25SapInterfaceType).
Default Value: true (2)
Related Objects:
x25Billing
x25SapPvcBillingTimer
x25SapSbscrChargingInformation
x25PvcBilling
x25PvcSrcAddress
x25PvcDstAddress
x25BillingIndication
x25SapInterfaceType
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.95 |
x25SapSbscrCallingAddressValidationThis object applies only to lower SAPs (service access points).
Determines if this SAP subscribes to the Calling Address Validation
facility. This facility applies to incoming calls only. This facility can
be used for security purposes to restrict calls originating from a
specific source.
Options:
false (1): Not subscribed. This SAP does not insert nor validate any
calling address contained within incoming calls.
true (2): Subscribed: This SAP inserts the calling address
(x25SapSourceAddress) into incoming call packets that do not contain one,
prior to routing the call. For incoming calls that do contain a calling
address, this SAP validates it against that specified address
(x25SapSourceAddress). If the addresses match, the incoming call is
routed, otherwise the incoming call is cleared.
Default Value: false (2)
Related Objects:
x25SapSourceAddress
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.96 |
x25SapSourceAddressThis object applies only to lower SAPs (service access points).
Determines the calling address used by this SAP when it subscribes to the
Calling Address Validation facility.
Range of Values: DTE address enclosed in quotes (up to 15 characters in
length)
Default Value: none
Related Objects:
x25SapSbscrCallingAddressValidation
Configuration Changed: administrative and operativerw X25Address .1.3.6.1.4.1.495.2.1.6.29.21.1.97 |
x25SapSbscrRouteUsingCUDFDetermines if this SAP subscribes to the Call User Data facility for
routing. This facility applies to incoming calls only.
Each SAP can only subscribe to one of the following routing decisions:
- Route using the call user data field (object x25SapRouteUsingCUDF)
- Route using sub-address (object x25SapRouteUsingSubAddress)
- Route using the called address extension facility (object
x25SapRouteUsingCAE)
Options:
false (1): Not subscribed. This SAP does not look at the call user data
field for routing information.
true (2): Subscribed: This SAP uses digits found in the call user data
field of incoming calls as the destination address for routing. The number
of digits to be used from the call user data field is defined by object
x25SapRouteAddressLength.
Default Value: false (1)
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.98 |
x25SapSbscrRouteUsingSubAddressDetermines if this SAP uses the subaddress field for routing. This
facility applies to incoming calls only.
Each SAP can only subscribe to one of the following routing decisions:
- Route using the call user data field (object x25SapRouteUsingCUDF)
- Route using sub-address (object x25SapRouteUsingSubAddress)
- Route using the called address extension facility (object
x25SapRouteUsingCAE)
Options:
false (1): Not subscribed. This SAP does not look at the subaddress field
for routing information.
true (2): Subscribed: This SAP uses digits found in the called address of
incoming calls as the destination address for routing. The number of
digits used as the subaddress is defined by object
x25SapRouteAddressLength
Default Value: false (1)
Related Objects:
x25SapRouteAddressLength
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.99 |
x25SapSbscrRouteUsingCAEDetermines if this SAP uses the called address extension facility for
routing. This facility applies to incoming calls only.
Each SAP can only subscribe to one of the following routing decisions:
-Route using the call user data field (object x25SapRouteUsingCUDF)
-Route using sub-address (object x25SapRouteUsingSubAddress)
-Route using the called address extension facility (object
x25SapRouteUsingCAE)
Options:
false (1): Not subscribed. This SAP does not look at the called address
extension facility for routing information.
true (2): Subscribed: This SAP uses digits found in the called address
extension facility of incoming calls as the destination address for
routing. The number of digits used for routing is specified as part of the
facility within the incoming call. This SAP will refuse the incoming call
if the called address extension facility is not present.
Default Value: false (1)
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.100 |
x25SapRouteAddressLengthDetermines the number of digits this SAP uses as the destination address
when routing incoming calls. This applies when one of the following
routing decisions are set for this SAP:
- x25SapRouteUsingCUDF
- x25SapRouteUsingSubAddress: digits used for the subaddress are counted
backward starting at last digit in the called address
Range of Values: 0 - 15
Default Value: 0
Configuration Changed: administrative and operativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.21.1.101 |
x25SapSbscrTransitDelayThis object applies only to lower SAPs (service access points).
Determines if this SAP subscribes to the Calling Address Validation
facility. This facility applies to both incoming and outgoing calls.
Options:
true (1): Subscribed: This SAP appends the transit delay facility (with
the value specified by object x25SapTransitDelay) to incoming/outgoing
calls that do not already contain the transit delay facility.
false (2): Not subscribed. This SAP does append the transit delay
facility.
Default Value: false (1)
Related Objects:
x25SapTransitDelay
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.102 |
x25SapTransitDelayThis object applies only to lower SAPs (service access points).
Defines the transit delay appended by this SAP if it subscribes to the
transit delay facility. This facility applies to both incoming and
outgoing calls.
Range of Values: 0 - 65535
Default Value: 0
Related Objects:
x25SapSbscrTransitDelay
Configuration Changed: administrative and operativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.21.1.103 |
x25SapSbscrCugIncomingAccessDetermines if this SAP subscribes to the Closed User Group with Incoming
Access facility. This facility applies to outgoing calls only.
Options:
false (1): Not subscribed. If this SAP is part of a closed user group,
outgoing calls not containing the closed user group selection facility
(calls from the open network which are not part of any CUGs) are refused.
true (2): Subscribed: If this SAP is part of a closed user group, outgoing
calls not containing the closed user group selection facility (calls from
the open network which are not part of any CUGs) are sent out. At the
upper SAP, they are sent to the attached application, at the lower SAP are
sent out to the line.
Default Value: false (1)
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.104 |
x25SapSbscrCugOutgoingAccessDetermines if this SAP subscribes to the Closed User Group with Outgoing
Access facility. This facility applies to incoming calls only.
Options:
false (1): Not subscribed. If this SAP is part of a closed user group,
incoming calls not containing the closed user group selection facility
(calls from the open network which are not part of any CUG) are refused.
true (2): Subscribed: If this SAP is part of a closed user group, incoming
calls not containing the closed user group selection Facility (calls from
the open network which are not part of any CUG), are routed.
Default Value: false (1)
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.105 |
x25SapPreferentialCugIndexDetermines the preferential CUG index for this SAP. This is required when
this SAP belongs to more than one CUG.
Range of Values: 0 - 99 ('0' indicates no preferential CUG exits)
Default Value: 0 (no preferential CUG exists)
Configuration Changed: administrative and operativerw CugIndex .1.3.6.1.4.1.495.2.1.6.29.21.1.106 |
x25SapControlPermits control of a specific SAP (service access point).
Options:
clearStats (1): Clear all statistics stored by x25Sap statistics objects.
enableSap (2):. Lower SAPs only. Forces this SAP to attempt reconnection
to the sub-layer. A previous 'disableSap' must have been invoked. This may
force the LAPB link to issue a SABM frame (depending on its
configuration).
disableSap (3):. Lower SAPs only. Forces this SAP to disconnect from the
sub-layer. This may force the LAPB link to issue a DISC frame (depending
on its configuration).
Default Value: none
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.120 |
x25SapLinkStateDetermines the current state of this SAP (service access point).
Options:
connecting (1): In the process of establishing a call.
dataTransfer (2): In data transfer mode.
restartInternal (3): Sent a Restart Request packet.
restartExternal (4): Received a Restart Request packet. down (5): Not
functioning.ro Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.125 |
x25SapFlowControlStateIndicates the status of flow control on this SAP (service access point).
Flow control is initiated by this SAP when overall system resources drop
lower than the percentage specified by the global object
x25UpperPoolThreshold, and are terminated when the overall system
resources exceed the percentage specified by the global object
x25UpperPoolThreshold.
Options:
flowNormal (1): Data flow is normal. No flow control procedures are
active.
flowStopped (2): Flow control procedures are active, since overall system
resources have dropped lower than the percentage specified by global
object x25LowerPoolThreshold. noFlow (3): Indicates this SAP is configured
incorrectly.
Related Objects:
x25UpperPoolThresholdro Enumeration .1.3.6.1.4.1.495.2.1.6.29.21.1.126 |
x25SapStatsTableA table containing statistical information about each service access
point. SEQUENCE OF X25SapStatsEntry .1.3.6.1.4.1.495.2.1.6.29.22 |
x25SapStatsEntryThe statistical information for a specific service access point. X25SapStatsEntry .1.3.6.1.4.1.495.2.1.6.29.22.1 |
x25SapStatsSapNumberDetermines the lower X.25 layer SAP (service access point) these
statistics are associated with. This is the first half of the SAP
identification. The second half is specified by object x25SapStatsSapCes.ro SapIndex .1.3.6.1.4.1.495.2.1.6.29.22.1.1 |
x25SapStatsSapCesDetermines the lower X.25 layer SAP (service access point) these
statistics are associated with. This is the second half of the SAP
identification. The first half is specified by object
x25SapStatsSapNumber.ro Ces .1.3.6.1.4.1.495.2.1.6.29.22.1.2 |
x25SapStatsTxDataPktsIndicates the number of data packets transmitted by this SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.3 |
x25SapStatsRxDataPktsIndicates the number of data packets received by this SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.4 |
x25SapStatsTxDataCharsIndicates the number of data characters transmitted by this SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.5 |
x25SapStatsRxDataCharsIndicates the number of data characters received by this SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.6 |
x25SapStatsTxQDataPktsIndicates the number of Q-bit data packets transmitted by this SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.7 |
x25SapStatsRxQDataPktsIndicates the number of Q-bit data packets received by this SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.8 |
x25SapStatsTxQDataCharsIndicates the number of Q-bit data character transmitted by this SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.9 |
x25SapStatsRxQDataCharsIndicates the number of Q-bit data characters received by this SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.10 |
x25SapStatsTxCallPktsIndicates the number of Call Request packets transmitted by this SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.11 |
x25SapStatsRxCallPktsIndicates the number of Call Request packets received by this SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.12 |
x25SapStatsTxClrPktsIndicates the number of Clear packets transmitted by this SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.13 |
x25SapStatsRxClrPktsIndicates the number of Clear packets received by this SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.14 |
x25SapStatsTxRRPktsIndicates the number of Receiver Ready (RR) packets transmitted by this
SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.15 |
x25SapStatsRxRRPktsIndicates the number of Receiver Ready (RR) packets received by this
SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.16 |
x25SapStatsTxRNRPktsIndicates the number of Receiver Not Ready (RNR) packets transmitted by
this SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.17 |
x25SapStatsRxRNRPktsIndicates the number of Receiver Not Ready (RNR) packets received by this
SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.18 |
x25SapStatsTxResPktsIndicates the number of Reset packets transmitted by this SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.19 |
x25SapStatsRxResPktsIndicates the number of Reset packets received by this SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.20 |
x25SapStatsTxRstPktsThis object applies only to lower SAPs (service access points). Indicates
the number of Restart packets transmitted by this SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.21 |
x25SapStatsRxRstPktsThis object applies only to lower SAPs (service access points). Indicates
the number of Restart packets received by this SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.22 |
x25SapStatsTxIntPktsIndicates the number of Interrupt packets transmitted by this SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.23 |
x25SapStatsRxIntPktsIndicates the number of Interrupt packets received by this SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.24 |
x25SapStatsTxDiagPktsThis object applies only to lower SAPs (service access points). Indicates
the number of Diagnostic packets transmitted by this SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.25 |
x25SapStatsRxDiagPktsThis object applies only to lower SAPs (service access points). Indicates
the number of Diagnostic packets received by this SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.26 |
x25SapStatsRxInvPktsIndicates the number of packets that were received by this SAP, but were
discarded because they were invalid for the state the X.25 interface was
in at the time.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.27 |
x25SapStatsConsFor future use. Indicates the number of connections established through
this SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.28 |
x25SapStatsDiscsFor future use. Indicates the number of disconnects through this SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.29 |
x25SapStatsLastCauseCodeIndicates the last cause code received by this SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.30 |
x25SapStatsLastDiagCodeIndicates the last diagnostics code received by this SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.31 |
x25SapStatsActiveLcnsFor future use. Indicates the active number of open logical channels at
this SAP.ro Counter .1.3.6.1.4.1.495.2.1.6.29.22.1.32 |
x25CugTableThis tables contains CUG (closed user group) definitions for the X.25
layer. Any service access point (upper or lower) can be part of one or
more CUGs.
Each row in the table identifies the CUG parameters for a single member of
the specified CUG.
CUGs provide the means to regulate incoming and outgoing calls at
particular SAP. Generally, members of a CUG are defined to only support
making and receiving calls from other members of the group. However, other
options are available.
When a SAP belongs to more than one closed user group, a preferential
closed user group must be specified.
Each CUG entry consists of an interlock code and the facilities for
incoming/outgoing calls barred within the CUG.
Objects in this table make references to the appropriate sections in the
blue book: ITU(CCITT) X.25 Recommendation (1988). The reference is
specified in the REFERENCE section of an object.
Only BASIC CUGs are supported. SEQUENCE OF X25CugEntry .1.3.6.1.4.1.495.2.1.6.29.23 |
x25CugEntryDefines a row in the x25CugTable. Each row contains the objects which
define a member of a closed user group. X25CugEntry .1.3.6.1.4.1.495.2.1.6.29.23.1 |
x25CugSapNumberIdentifies the SAP (service access point) this entry is associated with.
This is the first half of the SAP identification. The second half is
specified by object x25CugSapCes.
Range of Values: 1 - 255
Default Value: none
Related Objects:
x25CugSapCes
Configuration Changed: administrative and operativero SapIndex .1.3.6.1.4.1.495.2.1.6.29.23.1.1 |
x25CugSapCesIdentifies the CES (connection endpoint suffix) this entry is associated
with. This is the second half of the SAP identification. The first half is
specified by object x25CugSapNumbers.
Range of Values: 0 - 63
Default Value: none
Configuration Changed: administrative and operativero Ces .1.3.6.1.4.1.495.2.1.6.29.23.1.2 |
x25CugIndexDetermines the CUG index assigned to this member for use when routing
outgoing CUG calls, or for validating when receiving incoming CUG calls. A
value of '0' is not permitted for this object.
Range of Values: 1 - 99
Default Value: none
Configuration Changed: administrative and operativero CugIndex .1.3.6.1.4.1.495.2.1.6.29.23.1.3 |
x25CugRowStatusDetermines the status of the objects in a table row.
Options:
invalid (1): Row is deleted from the table immediately, however values are
still in effect until the next reset.
valid (2): Use this value to add a new row to the table, or modify an
existing row.
Default Value: valid (2)
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.23.1.4 |
x25CugInterlockCodeDetermines the CUG (closed user group) that member belongs to. This
number also represents the interlock code used by the layer when
translating index codes from one member to another. Interlock codes must
be unique at each SAP.
Range of Values: 0 - 65535
Default Value: none
Configuration Changed: administrative and operativerw CugIC .1.3.6.1.4.1.495.2.1.6.29.23.1.5 |
x25CugSbscrInCallsBarredDetermines if this SAP subscribes to the Incoming Calls Barred with a
Closed User Group facility.
Options:
false (1): Not subscribed.
true (2): Subscribed: Permits this member to originate virtual calls to
other members in this closed user group, but prevents the reception of
incoming calls from other members in this closed user group.
Default Value: false (1)
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.23.1.6 |
x25CugSbscrOutCallsBarredDetermines if this SAP subscribes to the Outgoing Calls Barred with a
Closed User Group facility.
Options:
false (1): Not subscribed.
true (2): Subscribed: Permits this member to originate virtual calls to
other members in this closed user group, but prevents this member from
originating virtual calls to other members in this closed user group.
Default Value: false (1)
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.23.1.7 |
x25CugEntryStateDetermines the state of the CUG (closed user group) entry.
Options:
offLine (1): Indicates this CUG entry has not been configured.
onLine (2): Indicates that this CUG entry has been configured.ro Enumeration .1.3.6.1.4.1.495.2.1.6.29.23.1.8 |
x25RouteTableThe SVC Route table contains the definitions used to route all switched
virtual circuits.
A route entry consists of the called address that activates the route, and
a destination. Four categories of destinations are available, providing
four possible route types.
- 1) Route to a specific upper SAP destination.
- 2) Route to a specific lower SAP destination. This type of route can be
used in place of route type 3, when route balancing is not required. This
avoids the need to configure a logical link containing only one SAP entry,
which is ideal for LAPB routing when no load balancing is required. This
type of route is also ideal when targeting a specific data link connection
(identified by the CES) on a LAPD link.
3) Route to a logical link destination. A logical link is a grouping of
one or more lower SAPs for the purpose of route balancing.
4) Route to a hunt group destination. A hunt group consists of one or more
SAPs (upper or lower) which are grouped for the purpose of route hunting. SEQUENCE OF X25RouteEntry .1.3.6.1.4.1.495.2.1.6.29.24 |
x25RouteEntryDefines a row in the x25RouteTable. Each row contains the objects which
define a route for switched virtual circuits. X25RouteEntry .1.3.6.1.4.1.495.2.1.6.29.24.1 |
x25RoutePartitionIdentifies the partition within the route table that this route belongs
to. Not significant for routing.ro RoutePartition .1.3.6.1.4.1.495.2.1.6.29.24.1.1 |
x25RouteIdThe index of the route within the partition. Not significant for
routing.ro RouteIndex .1.3.6.1.4.1.495.2.1.6.29.24.1.2 |
x25RouteRowStatusDetermines the status of the objects in a table row.
Options:
invalid (1): Row is deleted from the table immediately, however values are
still in effect until the next reset.
valid (2): Use this value to add a new row to the table, or modify an
existing row.
Default Value: valid (2)
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.24.1.3 |
x25RouteTypeDetermines the type of route this entry defines.
Options:
specUpperSap (1): Route to a specific upper SAP.
specLowerSap (2): Rout to a specific lower SAP.
logicalLink (3): Route to a logical link.
huntGroup (4): Route to a Hunt Group.
Configuration Changed: administrative and operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.24.1.4 |
x25RouteAddressDetermines the called DTE address that triggers routing. If an incoming
call is received at any upper or lower SAP with this address, it is routed
to the destination SAP defined by x25RouteType.
Options: none
Range of Values: DTE address enclosed in quotes (up to 15 characters in
length)
Default Value: none
Related Objects:
x25RouteType
Configuration Changed: administrative and operativerw X25Address .1.3.6.1.4.1.495.2.1.6.29.24.1.5 |
x25RouteSLHNumberDetermines the destination SAP, logical link, or Hunt Group to route to.
The destination depends on the setting of x25RouteType.
- If x25RouteType = 1 then this object specifies an upper SAP number.
- If x25RouteType = 2 then this object specifies a lower SAP number.
- If x25RouteType = 3 then this object specifies the number of the logical
link group to use.
- If x25RouteType = 4 then this object specifies the number of the Hunt
Group to use.
Default Value: none
Related Objects:
x25RouteType
Configuration Changed: administrative and operativerw SapIndex .1.3.6.1.4.1.495.2.1.6.29.24.1.6 |
x25RouteSapCesDetermines the CES number to route to. The value you set depends on the
setting of x25RouteType.
- If x25RouteType = 1 then this object must be set to 0.
- If x25RouteType = 2 then this object must be set to a valid CES for the
associated SAP (x25LLSapCes).
- If x25RouteType = 3 or 4 this object is not used.
Range of Values: 0 - 99
Default Value: 0
Related Objects:
x25RouteType
x25LLSapCes
Configuration Changed: administrative and operativerw Ces .1.3.6.1.4.1.495.2.1.6.29.24.1.7 |
x25RouteEntryStateDetermines the state of the route entry.
Options:
offLine (1): Indicates this route entry has not been configured.
onLine (2): Indicates that this route entry has been configured.ro Enumeration .1.3.6.1.4.1.495.2.1.6.29.24.1.8 |
x25HuntGroupTableThis table contains Hunt Group definitions for the X.25 layer. A hunt
group is a grouping of upper and lower SAPs (service access points) for
the purpose of routing incoming switched virtual circuit calls. A SAP can
belong to more than one hunt group at the same time.
Additions to this table are offline only. To determine the list of active
Hunt Groups members, see the x25HuntGroupOperTable.
Any incoming call whose address is determined to be associated with a hunt
group (via the routing table), is subjected to hunting. Hunting means that
the incoming call is routed to the first member of the hunt group. If this
member refuses the call, the next member is attempted, and so on. If all
members of a hunt group refuse the call, the call is refused back to its
source.
Enabling hunt group rotation (x25HuntGroupRotation) causes hunting to
begin with a different hunt group member each time. For example, a group
with three members would be hunted as follows: 123, 231, 312, 123. Members
are identified by x25HGMember Index.
Hunt groups can only be used via a route entry, they cannot be used stand
alone. SEQUENCE OF X25HuntGroupEntry .1.3.6.1.4.1.495.2.1.6.29.25 |
x25HuntGroupEntryDefines a row in the x25HuntGroupTable. Each row contains the objects
which define the parameters for one member of a hunt group. X25HuntGroupEntry .1.3.6.1.4.1.495.2.1.6.29.25.1 |
x25HGIdIdentifies the hunt group that the member belongs to.
Range of Values: 1 - 99
Default Value: none
Configuration Changed: administrativero HGIndex .1.3.6.1.4.1.495.2.1.6.29.25.1.1 |
x25HGMemberIndexIdentifies the order of the member within the hunt group.
Range of Values: 1 - 99
Default Value: none
Configuration Changed: administrativero HGIndex .1.3.6.1.4.1.495.2.1.6.29.25.1.2 |
x25HGSapNumberIdentifies the SAP (service access point) this entry is associated with.
This is the first half of the SAP identification. The second half is
specified by object x25HGSapCes.
Range of Values: 1 - 255
Default Value: none
Configuration Changed: administrativerw SapIndex .1.3.6.1.4.1.495.2.1.6.29.25.1.3 |
x25HGSapCesIdentifies the CES (connection endpoint suffix) this entry is associated
with. This is the second half of the SAP identification. The first half is
specified by object x25HGSapNumbers.
Range of Values: 1 - 255
Default Value: 0
Configuration Changed: administrativerw Ces .1.3.6.1.4.1.495.2.1.6.29.25.1.4 |
x25HGRowStatusDetermines the status of the objects in a table row.
Options:
invalid (1): Row is deleted from the table immediately, however values are
still in effect until the next reset.
valid (2): Use this value to add a new row to the table, or modify an
existing row.
Default Value: valid (2)
Configuration Changed: administrativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.25.1.5 |
x25HuntGroupOperTableThis table contains the current active Hunt Group (closed user group)
definitions for the X.25 layer. Use the x25HuntGroupTable to define Hunt
Group members. When a system reset occurs the definitions in
x25HuntGroupTable become active and appear here. SEQUENCE OF X25HuntGroupOperEntry .1.3.6.1.4.1.495.2.1.6.29.26 |
x25HuntGroupOperEntryIdentifies one operational member of a hunt group. X25HuntGroupOperEntry .1.3.6.1.4.1.495.2.1.6.29.26.1 |
x25HGOperIdIdentifies the hunt group that this operational member belongs to.ro HGIndex .1.3.6.1.4.1.495.2.1.6.29.26.1.1 |
x25HGOperMemberIndexIdentifies the order of this operational member within the hunt group.ro HGIndex .1.3.6.1.4.1.495.2.1.6.29.26.1.2 |
x25HGOperSapNumberIdentifies the SAP (service access point) this entry is associated with.
This is the first half of the SAP identification. The second half is
specified by object x25HGOperSapCes.ro SapIndex .1.3.6.1.4.1.495.2.1.6.29.26.1.3 |
x25HGOperSapCesIdentifies the CES (connection endpoint suffix) this entry is associated
with. This is the second half of the SAP identification. The first half is
specified by object x25HGOperSapNumbers.ro Ces .1.3.6.1.4.1.495.2.1.6.29.26.1.4 |
x25PvcTableThis table contains definitions used to route X.25 PVCs (permanent
virtual circuits). A PVC is always routed between two lower SAPs, or
between a lower SAP and an upper SAP.
The source SAP must always be a lower SAP. The destination SAP can be
either an upper or lower SAP. SEQUENCE OF X25PvcEntry .1.3.6.1.4.1.495.2.1.6.29.27 |
x25PvcEntryDefines a row in the x25PvcTable. Each row contains the objects which
define a route for a permanent virtual circuit. X25PvcEntry .1.3.6.1.4.1.495.2.1.6.29.27.1 |
x25PvcIdThe index of the PVC within the table. No significance for routing.ro PvcIndex .1.3.6.1.4.1.495.2.1.6.29.27.1.1 |
x25PvcRowStatusDetermines the status of the objects in a table row.
Options:
invalid (1): Row is deleted from the table immediately, however values are
still in effect until the next reset.
valid (2): Use this value to add a new row to the table, or modify an
existing row.
Default Value: valid (2)
Configuration Changed: administrativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.27.1.2 |
x25PvcSrcSapDetermines the source SAP (service access point) for the PVC, which must
be a lower SAP. This is the first half of the SAP identification. The
second half is specified by object x25PvcSrcCes.
Related Objects:
x25PvcSrcCes
Default Value: none
Range of Values: 1 - 255
Configuration Changed: administrativerw SapIndex .1.3.6.1.4.1.495.2.1.6.29.27.1.3 |
x25PvcSrcCesIdentifies the source SAP for the PVC, which must be a lower SAP. This is
the second half of the SAP identification. The first half is specified by
object x25PvcSrcSap.
Range of Values: 0 - 63
Default Value: 0
Related Objects:
x25PvcSrcSap
Configuration Changed: administrativerw Ces .1.3.6.1.4.1.495.2.1.6.29.27.1.4 |
x25PvcDstSapDetermines the destination SAP (service access point) for the PVC, which
can be an upper or lower SAP. This is the first half of the SAP
identification. The second half is specified by object x25PvcDstCes.
Range of Values: 1 - 255
Default Value: none
Related Objects:
x25PvcDstCes
Configuration Changed: administrativerw SapIndex .1.3.6.1.4.1.495.2.1.6.29.27.1.5 |
x25PvcDstCesIdentifies the destination SAP for the PVC, which can be an upper or
lower SAP. This is the second half of the SAP identification. The first
half is specified by object x25PvcDstSap.
Range of Values: 0 - 63
Default Value: 0
Related Objects:
x25PvcDstSap
Configuration Changed: administrativerw Ces .1.3.6.1.4.1.495.2.1.6.29.27.1.6 |
x25PvcSrcLcnDetermines the LCN (logical channel number) used by this PVC at the
source SAP (service access point). The value assigned must be within the
range of PVC LCNs assigned to the source SAP (x25SapLpvcLcn and
X25SapHpvcLcn).
Range of Values: 1 - 1023
Default Value: none
Related Objects:
x25SapLpvcLcn
X25SapHpvcLcn
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.27.1.7 |
x25PvcDstLcnDetermines the LCN (logical channel number) used by this PVC at the
source SAP (service access point). The value assigned must be within the
range of PVC LCNs assigned to the destination SAP (x25SapLpvcLcn and
X25SapHpvcLcn).
Range of Values: 1 - 1023
Default Value: none
Related Objects:
x25SapLpvcLcn
X25SapHpvcLcn
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.27.1.8 |
x25PvcSrcRxPacketSizeDetermines the receive packet size used by the associated source SAP
(service access point). This overrides the default settings for the SAP.
Options:
bytes16 (4)
bytes32 (5)
bytes64 (6)
bytes128 (7)
bytes256 (8)
bytes512 (9)
bytes1024 (10)
bytes2048 (11)
bytes4096 (12)
Default Value: bytes128 (7)
Configuration Changed: administrativerw PacketSize .1.3.6.1.4.1.495.2.1.6.29.27.1.9 |
x25PvcSrcTxPacketSizeDetermines the transmit packet size used by the associated source SAP
(service access point). This overrides the default settings for the SAP.
Options:
bytes16 (4)
bytes32 (5)
bytes64 (6)
bytes128 (7)
bytes256 (8)
bytes512 (9)
bytes1024 (10)
bytes2048 (11)
bytes4096 (12)
Default Value: bytes128 (7)
Configuration Changed: administrativerw PacketSize .1.3.6.1.4.1.495.2.1.6.29.27.1.10 |
x25PvcDstRxPacketSizeDetermines the receive packet size used by the associated destination SAP
(service access point). This overrides the default settings for the SAP.
Options:
bytes16 (4)
bytes32 (5)
bytes64 (6)
bytes128 (7)
bytes256 (8)
bytes512 (9)
bytes1024 (10)
bytes2048 (11)
bytes4096 (12)
Default Value: bytes128 (7)
Configuration Changed: administrativerw PacketSize .1.3.6.1.4.1.495.2.1.6.29.27.1.11 |
x25PvcDstTxPacketSizeDetermines the receive packet size used by the associated destination SAP
(service access point). This overrides the default settings for the SAP.
Options:
bytes16 (4)
bytes32 (5)
bytes64 (6)
bytes128 (7)
bytes256 (8)
bytes512 (9)
bytes1024 (10)
bytes2048 (11)
bytes4096 (12)
Default Value: bytes128 (7)
Configuration Changed: administrativerw PacketSize .1.3.6.1.4.1.495.2.1.6.29.27.1.12 |
x25PvcRxWindowDetermines the receive window size. At the source side, it defines the
window for packets received from the source interface. At the destination
side, it defines the window for packets transmitted to the destination
interface. This overrides the default settings for the SAP.
Range of Values: 1 - 7 for modulo 8
1 - 127 for modulo 128
Default Value: 7
Related Objects:
x25SapModulo
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.27.1.13 |
x25PvcTxWindowDetermines the transmit window size. At the source side, it defines the
window for packets transmitted to the source interface. At the destination
side, it defines the window for packets received from the destination
interface. This overrides the default settings for the SAP.
Range of Values: 1 - 7 for modulo 8
1 - 127 for modulo 128
Default Value: 7
Related Objects:
x25SapModulo
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.29.27.1.14 |
x25PvcRxThruputClassDetermines the receive throughput class for the external link. At the
source side, it defines the throughput class used for packets received
from the source interface. At the destination side, it defines the
throughput class used for packets transmitted to the destination
interface. This overrides the default settings for the SAP.
Options:
bps75 (3)
bps150 (4)
bps300 (5)
bps600 (6)
bps1200 (7)
bps2400 (8)
bps4800 (9)
bps9600 (10)
bps19200 (11)
bps48000 (12)
bps64000 (13)
Default Value: bps9600 (10)
Configuration Changed: administrativerw ThruputClass .1.3.6.1.4.1.495.2.1.6.29.27.1.15 |
x25PvcTxThruputClassThe transmit throughput class across the line. At the source side, it
defines the throughput class used for packets transmitted to the source
interface. At the destination side, it defines the throughput class used
for packets received from the destination interface (service access
point). This overrides the default settings for the SAP.
Options:
bps75 (3)
bps150 (4)
bps300 (5)
bps600 (6)
bps1200 (7)
bps2400 (8)
bps4800 (9)
bps9600 (10)
bps19200 (11)
bps48000 (12)
bps64000 (13)
Default Value: bps9600 (10)
Configuration Changed: administrativerw ThruputClass .1.3.6.1.4.1.495.2.1.6.29.27.1.16 |
x25PvcBillingDetermines if billing information is collected for this PVC. Billing
information can only be collected for lower SAPs (service access points).
If both sides of a PVC are lower SAPs, each side can collect its own
information. The x25SapPvcBillingTimer determines when billing information
is generated.
Options:
false (1): Not subscribed.
true (2): Subscribed.
Default Value: false (1)
Related Objects:
x25BillingSegmentSize
x25Billing
x25SapPvcBillingTimer
x25SapSbscrChargingInformation
x25SapSbscrNetworkUserId
x25PvcBilling
x25PvcSrcAddress
x25PvcDstAddress
x25BillingIndication
Configuration Changed: administrativerw Enumeration .1.3.6.1.4.1.495.2.1.6.29.27.1.17 |
x25PvcSrcAddressDetermines the X.121 address that is associated with the source side for
billing purposes only.
Range of Values: DTE address enclosed in quotes (up to 15 numeric
characters in length)
Default Value: none
Related Objects:
x25BillingSegmentSize
x25Billing
x25SapPvcBillingTimer
x25SapSbscrChargingInformation
x25SapSbscrNetworkUserId
x25PvcBilling
x25PvcDstAddress
x25BillingIndication
Configuration Changed: administrativerw X25Address .1.3.6.1.4.1.495.2.1.6.29.27.1.18 |
x25PvcDstAddressDetermines the X.121 address that is associated with the destination side
for billing purposes only.
Range of Values: DTE address enclosed in quotes (up to 15 characters in
length)
Default Value: none
Related Objects:
x25BillingSegmentSize
x25Billing
x25SapPvcBillingTimer
x25SapSbscrChargingInformation
x25SapSbscrNetworkUserId
x25PvcBilling
x25PvcSrcAddress
x25PvcDstAddress
x25BillingIndication
Configuration Changed: administrativerw X25Address .1.3.6.1.4.1.495.2.1.6.29.27.1.19 |
x25PvcEntryStateDetermines the state of this PVC entry.
Options:
offLine (1): Indicates this PVC entry has not been configured.
onLine (2): Indicates that this PVC entry has been configured.ro Enumeration .1.3.6.1.4.1.495.2.1.6.29.27.1.20 |
x25LcnStatusTableA table containing current information about established virtual circuits
(permanent or switched) within the layer. SEQUENCE OF X25LcnStatusEntry .1.3.6.1.4.1.495.2.1.6.29.28 |
x25LcnStatusEntryThe current information for a specific and currently established virtual
circuit (permanent or switched) within the layer. X25LcnStatusEntry .1.3.6.1.4.1.495.2.1.6.29.28.1 |
x25LcnSrcSapIdentifies the source side SAP (service access point) this entry is
associated with. This is the first half of the SAP identification. The
second half is specified by object x25LcnSrcCes.ro SapIndex .1.3.6.1.4.1.495.2.1.6.29.28.1.1 |
x25LcnSrcCesIdentifies the source side CES (connection endpoint suffix) this entry is
associated with. This is the second half of the SAP identification. The
first half is specified by object x25LcnSrcSap.ro Ces .1.3.6.1.4.1.495.2.1.6.29.28.1.2 |
x25LcnSrcLcnIdentifies the source side logical channel number this entry is
associated with.ro Lcn .1.3.6.1.4.1.495.2.1.6.29.28.1.3 |
x25LcnDstSapIdentifies the destination side SAP (service access point) this entry is
associated with. This is the first half of the SAP identification. The
second half is specified by object x25LcnSrcCes.ro SapIndex .1.3.6.1.4.1.495.2.1.6.29.28.1.4 |
x25LcnDstCesIdentifies the destination side CES (connection endpoint suffix) this
entry is associated with. This is the second half of the SAP
identification. The first half is specified by object x25LcnSrcSap.ro Ces .1.3.6.1.4.1.495.2.1.6.29.28.1.5 |
x25LcnDstLcnIndicates the destination side logical channel number this entry is
associated with.ro Lcn .1.3.6.1.4.1.495.2.1.6.29.28.1.6 |
x25LcnDBitCallIndicates if this virtual circuit was established using a D-bit call.
Options:
false (1): Not established using a D- bit call.
true (2): Established using a D-bit call.ro Enumeration .1.3.6.1.4.1.495.2.1.6.29.28.1.20 |
x25LcnPvcIndicates the virtual circuit type.
Options:
false (1): SVC (switched virtual circuit).
true (2): PVC (permanent virtual circuit).ro Enumeration .1.3.6.1.4.1.495.2.1.6.29.28.1.21 |
x25LcnModuloIndicates the modulus in use on this side of the virtual circuit. Modulus
determines the range of sequence numbers available for packet numbering.
Options:
modulo8 (1): Sequence numbers range from 0 to 7, supporting a maximum
window size of 8.
modulo128 (2): Sequence numbers range from 0 to 128, supporting a maximum
window size of 128.ro Enumeration .1.3.6.1.4.1.495.2.1.6.29.28.1.22 |
x25LcnStateIndicates the current state at this side of the virtual circuit.
Options:
stateReady (1):
SVC: Does not apply.
PVC: The PVC is configured. It remains in this state until a Restart
Request or Restart Confirm is received. This means that the PVC is in
limbo and cannot initiate its reset procedure until the restart procedure
has completed. The restart procedure brings up the packet level at the
port where the PVC exists.
stateConnecting (2)
SVC: The SAP has sent out a call and is waiting for a reply, or has
received a call and is routing that call out to another SAP (lower or
upper), and is also waiting for a reply.
PVC: Does not apply.
stateDataTransfer (3)
SVC: A connection has been accepted.
PVC: Reset procedure has been successful.
stateDisconnecting (4)
SVC: The SAP has sent out a clear and is waiting for a reply, or has
received a clear and is routing that clear out to another SAP (lower or
upper), and is also waiting for a reply. This state is only possible if
the previous state was 'stateDataTransfer'.
PVC: Does not apply.
This following paragraph applies to the next three states: When a
connection is established (SVC or PVC), a 'connection block' is assigned
to each side of the connection. One side is always termed as the 'called'
side and the other the 'calling' side. For a PVC, the source side is
always the 'calling' and the destination side is always the 'called'. For
an SVC, the side that receives the call is the 'calling' side, and the
other is the 'called'. This makes sense since we are routing the call
towards the called user.
stateResettingCgSide (5) SVC/PVC: A reset was received at the called side.
The called side confirms the reset at its side, and a reset is also sent
to the calling side. Both sides enter this state awaiting a confirmation
at the calling side.
state ResettingCdSide (6) SVC/PVC: A reset is received at the calling
side. The calling side confirms the reset at its side, and a reset is also
sent to the called side. Both sides enter this state awaiting a
confirmation at the 'called' side.
stateResettingBoth (7) SVC/PVC: This state is entered when a reset is
generated internally at both the calling and called sides. Both sides
enter the this state, each while waiting for a confirmation.ro Enumeration .1.3.6.1.4.1.495.2.1.6.29.28.1.23 |
x25LcnTxRnrIndicates if this side of the virtual circuit has initiated flow control
by sending an RNR.
Options:
false (1): An RNR was not sent.
true (2): An RNR was sent.ro Enumeration .1.3.6.1.4.1.495.2.1.6.29.28.1.30 |
x25LcnRxRnrIndicates if this side of the virtual circuit has received an RNR.
Options:
false (1): An RNR was not received.
true (2): An RNR was received.ro Enumeration .1.3.6.1.4.1.495.2.1.6.29.28.1.31 |
x25LcnTxWindowSizeIndicates the transmit window size in use at this side of the virtual
circuit.ro INTEGER .1.3.6.1.4.1.495.2.1.6.29.28.1.32 |
x25LcnRxWindowSizeIndicates the receive window size in use at this side of the virtual
circuit.ro INTEGER .1.3.6.1.4.1.495.2.1.6.29.28.1.33 |
x25LcnTxPacketSizeIndicates the transmit packet size (in bytes) in use at this side of the
virtual circuit.ro INTEGER .1.3.6.1.4.1.495.2.1.6.29.28.1.34 |
x25LcnRxPacketSizeIndicates the receive packet size (in bytes) in use at this side of the
virtual circuit.ro INTEGER .1.3.6.1.4.1.495.2.1.6.29.28.1.35 |
x25LcnTxThruputClassIndicates the transmit throughput class (in bps) in use at this side of
the virtual circuit.ro INTEGER .1.3.6.1.4.1.495.2.1.6.29.28.1.36 |
x25LcnRxThruputClassIndicates the receive throughput class (in bps) in use at this side of
the virtual circuit.ro INTEGER .1.3.6.1.4.1.495.2.1.6.29.28.1.37 |
x25LcnSrcAddressIndicates the calling address specified when this virtual circuit was
established.ro X25Address .1.3.6.1.4.1.495.2.1.6.29.28.1.50 |
x25LcnDstAddressIndicates the called address specified when this virtual circuit was
established.ro X25Address .1.3.6.1.4.1.495.2.1.6.29.28.1.51 |
x25LcnTxQLengthIndicates the current number of outbound queued frames at this side of
the virtual circuit.ro INTEGER .1.3.6.1.4.1.495.2.1.6.29.28.1.60 |
x25LcnNextTransmitPsIndicates the next P(s) to be used at this side of the virtual circuit.ro INTEGER .1.3.6.1.4.1.495.2.1.6.29.28.1.61 |
x25LcnNextExpectedPsIndicates the next expected P(s) at this side of the virtual circuit.ro INTEGER .1.3.6.1.4.1.495.2.1.6.29.28.1.62 |
x25LcnLastTransmittedPrIndicates the last transmitted P(r) at this side of the virtual circuit.ro INTEGER .1.3.6.1.4.1.495.2.1.6.29.28.1.63 |
x25LcnLastReceivedPrIndicates the last received P(r) on this side of the virtual circuit.ro INTEGER .1.3.6.1.4.1.495.2.1.6.29.28.1.64 |
x25LcnFCTimerRunningIndicates if the flow control timer (object x25SapFlowControlTimer) is
currently running on this side of the virtual circuit.
Options:
false (1): x25SapFlowControlTimer is not running.
true (2): x25SapFlowControlTimer is running.ro Enumeration .1.3.6.1.4.1.495.2.1.6.29.28.1.80 |
x25LcnT24TimerRunningIndicates if the window status timer (object x25SapWindowStatusTimer) is
currently running on this side of the virtual circuit.
Options:
false (1): x25SapWindowStatusTimer is not running.
true (2): x25SapWindowStatusTimer is running.ro Enumeration .1.3.6.1.4.1.495.2.1.6.29.28.1.81 |
x25LcnInacTimerRunningIndicates if the inactivity timer (object x25SapInactivityTimer) is
currently running on this side of the virtual circuit.
Options:
false (1): x25SapInactivityTimer is not running.
true (2): x25SapInactivityTimer is running.ro Enumeration .1.3.6.1.4.1.495.2.1.6.29.28.1.82 |
x25LcnCalTimerRunningIndicates if the call request timer (object x25SapCallTimer) is currently
running on this side of the virtual circuit.
Options:
false (1): x25SapCallTimer is not running.
true (2): x25SapCallTimer is running.ro Enumeration .1.3.6.1.4.1.495.2.1.6.29.28.1.83 |
x25LcnClrTimerRunningIndicates if the clear timer (object x25SapClearTimer) is currently
running on this side of the virtual circuit.
Options:
false (1): x25SapClearTimer is not running.
true (2): x25SapClearTimer is running.ro Enumeration .1.3.6.1.4.1.495.2.1.6.29.28.1.84 |
x25LcnResTimerRunningIndicates if the reset timer (object x25SapResetTimer) is currently
running on this side of the virtual circuit.
Options:
false (1): x25SapResetTimer is not running.
true (2): x25SapResetTimer is running.ro Enumeration .1.3.6.1.4.1.495.2.1.6.29.28.1.85 |
x25MibLevelUsed to determine current MIB module release supported
by the agent. Object is in decimal.ro INTEGER .1.3.6.1.4.1.495.2.1.6.29.30 |