RBTWS-TRAP-MIB
AI MIB Summary
The RBTWS-TRAP-MIB defines SNMP trap notifications generated by Enterasys Networks wireless switches (Access Controllers) to report critical operational events and state changes for associated Access Points. This module enables centralized monitoring of wireless infrastructure health by alerting management systems to specific AP association failures, disconnections, and controller-level anomalies.
Notifications emitted by Enterasys Networks wireless switches. AP = Access Point; AC = Access Controller (wireless switch), the device that runs a SNMP Agent implementing this MIB. Copyright 2008 Enterasys Networks, Inc. All rights reserved. This SNMP Management Information Base Specification (Specification) embodies confidential and proprietary intellectual property. This Specification is supplied 'AS IS' and Enterasys Networks makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification.
Main OID:
rbtwsTrapMib.1.3.6.1.4.1.52.4.15.1.4.1
177
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
177 total| Object Name |
|---|
rbtwsDeviceIdEnumeration of devices as indicated in registration MIB. This object is used within notifications and is not accessible.ro OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.15.1.2.1 |
rbtwsMobilityDomainIpIP address of the other switch which the send switch is reporting on. This object is used within notifications and is not accessible.ro IpAddress .1.3.6.1.4.1.52.4.15.1.2.2 |
rbtwsAPMACAddressMAC address of the AP of interest. This object is used within notifications and is not accessible.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.52.4.15.1.2.3 |
rbtwsClientMACAddressMAC address of the client of interest. This object is used within notifications and is not accessible.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.52.4.15.1.2.4 |
rbtwsRFDetectXmtrMacAddrDescribes the transmitter's MAC address. This object is used within notifications and is not accessible.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.52.4.15.1.2.5 |
rbtwsPortNumPort number on the AC which reported this rogue during a detection sweep. This object is used within notifications and is not accessible.ro INTEGER .1.3.6.1.4.1.52.4.15.1.2.6 |
rbtwsAPRadioNumRadio number of the AP which reported this rogue during a detection sweep. This object is used within notifications and is not accessible.ro RbtwsRadioNum (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.7 |
rbtwsRadioRssiThe received signal strength as measured by the AP radio which reported this rogue during a detection sweep. This object is used within notifications and is not accessible. Not used by any notification.roobsolete INTEGER .1.3.6.1.4.1.52.4.15.1.2.8 |
rbtwsRadioBSSIDThe basic service set identifier of the rogue from the beacon frame reported by the AP during a detection sweep. This object is used within notifications and is not accessible.ro OCTET STRING .1.3.6.1.4.1.52.4.15.1.2.9 |
rbtwsUserNameThe client user name as learned from the AAA process. This object is used within notifications and is not accessible.ro DisplayString .1.3.6.1.4.1.52.4.15.1.2.10 |
rbtwsClientAuthServerIpThe client authentication server ip address. This object is used within notifications and is not accessible.ro IpAddress .1.3.6.1.4.1.52.4.15.1.2.11 |
rbtwsClientSessionStateThe state for a client session. This object is used within notifications and is not accessible.ro RbtwsClientSessionState (RBTWS-CLIENT-SESSION-TC) .1.3.6.1.4.1.52.4.15.1.2.12 |
rbtwsDAPNumThe DAP number on the wireless switch. This object is used within notifications and is not accessible.ro INTEGER .1.3.6.1.4.1.52.4.15.1.2.13 |
rbtwsClientIpThe client ip address. This object is used within notifications and is not accessible.ro IpAddress .1.3.6.1.4.1.52.4.15.1.2.14 |
rbtwsClientSessionIdThe unique global id for a client session. This object is used within notifications and is not accessible.ro DisplayString .1.3.6.1.4.1.52.4.15.1.2.15 |
rbtwsClientAuthenProtocolTypeThe authentication protocol for a client. This object is used within notifications and is not accessible.ro RbtwsClientAuthenProtocolType (RBTWS-CLIENT-SESSION-TC) .1.3.6.1.4.1.52.4.15.1.2.16 |
rbtwsClientVLANNameThe vlan name a client is on. This object is used within notifications and is not accessible.ro DisplayString .1.3.6.1.4.1.52.4.15.1.2.17 |
rbtwsClientSessionStartTimeThe start time of a client session, relative to the sysUptime. This object is used within notifications and is not accessible. Obsolete. Do not use it because it's not vital information and often *cannot* be implemented to match the declared semantics: a client session might have been created on another wireless switch, *before* the current switch booted (the local zero of sysUptime).roobsolete TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.52.4.15.1.2.18 |
rbtwsClientFailureCauseDisplay string for possible failure cause for a client session. This object is used within notifications and is not accessible.ro DisplayString .1.3.6.1.4.1.52.4.15.1.2.19 |
rbtwsClientRoamedFromPortNumThe port number on the AC a client has roamed from. This object is used within notifications and is not accessible.ro INTEGER .1.3.6.1.4.1.52.4.15.1.2.20 |
rbtwsClientRoamedFromRadioNumThe radio number of the AP the client is roamed from. This object is used within notifications and is not accessible.ro RbtwsRadioNum (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.21 |
rbtwsClientRoamedFromDAPNumThe DAP number on the AC which reported this rogue during roam. This object is used within notifications and is not accessible.ro INTEGER .1.3.6.1.4.1.52.4.15.1.2.22 |
rbtwsUserParamsA display string of User Parameters for client user authorization attributes learned through AAA and/or used by the system. Note that the syntax will be (name=value, name=value,..) for the parsing purpose. This object is used within notifications and is not accessible.ro DisplayString .1.3.6.1.4.1.52.4.15.1.2.23 |
rbtwsClientLocationPolicyIndexIndex of the Location Policy rule applied to a user. This object is used within notifications and is not accessible.ro INTEGER .1.3.6.1.4.1.52.4.15.1.2.24 |
rbtwsClientAssociationFailureCauseThe client association failure cause. This object is used within notifications and is not accessible.ro RbtwsAssociationFailureType .1.3.6.1.4.1.52.4.15.1.2.25 |
rbtwsClientAuthenticationFailureCauseThe client authentication failure cause. This object is used within notifications and is not accessible.ro RbtwsAuthenticationFailureType .1.3.6.1.4.1.52.4.15.1.2.26 |
rbtwsClientAuthorizationFailureCauseThe client authorization failure cause. Note that if it is the user-param, we would additionally expect the failure cause description to list the user attribute value that caused the failure. This object is used within notifications and is not accessible.ro RbtwsAuthorizationFailureType .1.3.6.1.4.1.52.4.15.1.2.27 |
rbtwsClientFailureCauseDescriptionDisplay string for describing the client failure cause. This object is used within notifications and is not accessible.ro DisplayString .1.3.6.1.4.1.52.4.15.1.2.28 |
rbtwsClientRoamedFromWsIpThe system IP address of the AC (wireless switch) a client roamed from. This object is used within notifications and is not accessible.ro IpAddress .1.3.6.1.4.1.52.4.15.1.2.29 |
rbtwsClientRoamedFromAccessTypeThe client access type (ap, dap, wired) that a client roamed from. This object is used within notifications and is not accessible.ro RbtwsAccessType (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.30 |
rbtwsClientAccessTypeThe client access type (ap, dap, wired). This object is used within notifications and is not accessible. For new traps, use rbtwsClientAccessMode instead of this object.ro RbtwsAccessType (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.31 |
rbtwsRadioMACAddressAP Radio MAC address. This object is used within notifications and is not accessible.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.52.4.15.1.2.32 |
rbtwsRadioPowerChangeReasonThe type of event that caused an AP radio power change; occurs due to auto-tune operation. This object is used within notifications and is not accessible.ro RbtwsRadioPowerChangeType (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.33 |
rbtwsNewChannelNumNew channel number of the AP radio used after an auto tune event. This object is used within notifications and is not accessible.ro INTEGER .1.3.6.1.4.1.52.4.15.1.2.34 |
rbtwsOldChannelNumOld channel number of the AP radio used before an auto tune event. This object is used within notifications and is not accessible.ro INTEGER .1.3.6.1.4.1.52.4.15.1.2.35 |
rbtwsChannelChangeReasonThe type of event that caused an AP radio channel change; occurs due to auto-tune operation. This object is used within notifications and is not accessible.ro RbtwsChannelChangeType (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.36 |
rbtwsRFDetectListenerListInfoThe RF Detection Listener list info including a list of (listener mac, rssi, channel, ssid, time). There will be a maximum of 6 entries in the list. Formats: MAC: 18 bytes: %2.2X:%2.2X:%2.2X:%2.2X:%2.2X:%2.2X RSSI: 10 bytes: %10d CHANNEL: 3 bytes: %3d SSID: 32 bytes: %s TIME: 26 bytes: %s Maximum size per entry is 89+4+2 = 95 bytes. Maximum size of the string is 6*95= 571 bytes (include NULL). This object is used within notifications and is not accessible.ro OCTET STRING .1.3.6.1.4.1.52.4.15.1.2.37 |
rbtwsRadioSSIDThe radio SSID string This object is used within notifications and is not accessible.ro DisplayString .1.3.6.1.4.1.52.4.15.1.2.38 |
rbtwsNewPowerLevelNew power level of the AP radio used after an auto tune event. This object is used within notifications and is not accessible.ro RbtwsPowerLevel (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.39 |
rbtwsOldPowerLevelOld power level of the AP radio used before an auto tune event. This object is used within notifications and is not accessible.ro RbtwsPowerLevel (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.40 |
rbtwsRadioPowerChangeDescriptionThe radio power change description. In the case of reason being dup-pkts-threshold-exceed(1), and retransmit-threshold-exceed(2), clientMacAddress will be included in the description. This object is used within notifications and is not accessible.ro DisplayString .1.3.6.1.4.1.52.4.15.1.2.41 |
rbtwsCounterMeasurePerformerListInfoA list of information for APs performing Counter Measures including a list of performer mac addresses. This object is used within notifications and is not accessible. Not used by any notification.roobsolete DisplayString .1.3.6.1.4.1.52.4.15.1.2.42 |
rbtwsClientDot1xStateThe state for a client 802.1X. This object is used within notifications and is not accessible.ro RbtwsClientDot1xState (RBTWS-CLIENT-SESSION-TC) .1.3.6.1.4.1.52.4.15.1.2.43 |
rbtwsClientDot1xFailureCauseThe client 802.1X failure cause. This object is used within notifications and is not accessible.ro RbtwsDot1xFailureType .1.3.6.1.4.1.52.4.15.1.2.44 |
rbtwsAPAccessTypeThe access point access type (ap, dap,). This object is used within notifications and is not accessible. Not used by any notification.roobsolete RbtwsAccessType (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.45 |
rbtwsUserAccessTypeThe user access type (MAC, WEB, DOT1X, LAST-RESORT). This object is used within notifications and is not accessible.ro RbtwsUserAccessType (RBTWS-CLIENT-SESSION-TC) .1.3.6.1.4.1.52.4.15.1.2.46 |
rbtwsClientSessionElapsedTimeThe elapsed time for a client session. Obsoleted because session time is usually reported in seconds. This object is used within notifications and is not accessible.roobsolete TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.52.4.15.1.2.47 |
rbtwsLocalIdLocal Id for the session. This object is used within notifications and is not accessible.ro INTEGER .1.3.6.1.4.1.52.4.15.1.2.48 |
rbtwsRFDetectDoSTypeThe type of denial of service (DoS) attack. This object is used within notifications and is not accessible.ro RbtwsRFDetectDoSType .1.3.6.1.4.1.52.4.15.1.2.49 |
rbtwsSourceWsIpIP address of another AC (wireless switch). This object is used within notifications and is not accessible.ro IpAddress .1.3.6.1.4.1.52.4.15.1.2.50 |
rbtwsClientVLANidVLAN ID used by client traffic. This object is used within notifications and is not accessible.ro INTEGER .1.3.6.1.4.1.52.4.15.1.2.51 |
rbtwsClientVLANtagVLAN tag used by client traffic. This object is used within notifications and is not accessible.ro INTEGER .1.3.6.1.4.1.52.4.15.1.2.52 |
rbtwsDeviceModelThe model of a device in printable US-ASCII. If unknown (or not available), then the value is a zero length string. This object is used within notifications and is not accessible.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.52.4.15.1.2.53 |
rbtwsDeviceSerNumThe serial number of an AP in printable US-ASCII. If unknown (or not available), then the value is a zero length string. Should NOT be used to identify other devices, for example an AC (wireless switch). This object is used within notifications and is not accessible.ro RbtwsApSerialNum (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.54 |
rbtwsRsaPubKeyFingerPrintThe hash of the RSA public key (of a key pair) in binary form that uniquely identifies the public key of an AP. This object is used within notifications and is not accessible.ro RbtwsApFingerprint (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.55 |
rbtwsDAPconnectWarningTypeThe type of DAP connect warning. The values are: not-configured-fingerprint-connect(1)...a DAP, which has an RSA keypair but did not have its fingerprint configured on the AC, has connected to the AC when 'dap security' set to 'OPTIONAL' secure-handshake-failure(2).............a DAP tried to connect to the AC with security, but the handshake failed not-configured-fingerprint-required(3)..a DAP tried to connect to the AC with security, but 'dap security' set to 'REQUIRED', and no fingerprint was configured for the DAP fingerprint-mismatch(4).................a DAP tried to connect to the AC with security and its fingerprint was configured, but the fingerprint did not match the computed one This object is used within notifications and is not accessible.ro Enumeration .1.3.6.1.4.1.52.4.15.1.2.56 |
rbtwsClientMACAddress2MAC address of the second client of interest. This object is used within notifications and is not accessible.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.52.4.15.1.2.57 |
rbtwsApAttachTypeHow the AP is attached to the AC (directly or via L2/L3 network). This object is used within notifications and is not accessible.ro RbtwsApAttachType (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.58 |
rbtwsApPortOrDapNumThe Port Number if the AP is directly attached, or the CLI-assigned DAP Number if attached via L2/L3 network. This object is used within notifications and is not accessible. Obsoleted by rbtwsApNum. (In 6.0, direct- and network-attached APs were unified.)roobsolete RbtwsApPortOrDapNum (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.59 |
rbtwsApNameThe name of the AP, as assigned in AC's CLI; defaults to AP<Number> (examples: 'AP01', 'AP22', 'AP333', 'AP4444'); could have been changed from CLI to a meaningful name, for example the location of the AP (example: 'MeetingRoom73'). This object is used within notifications and is not accessible.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.52.4.15.1.2.60 |
rbtwsApTransitionAP state Transition, as seen by the AC. This object is used within notifications and is not accessible.ro RbtwsApTransition (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.61 |
rbtwsApFailDetailDetailed failure code for some of the transitions specified in 'rbtwsApTransition' object. This object is used within notifications and is not accessible.ro RbtwsApFailDetail (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.62 |
rbtwsRadioTypeIndicates the AP Radio Type, as seen by AC. This object is used within notifications and is not accessible.ro RbtwsRadioType (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.63 |
rbtwsRadioConfigStateIndicates the Radio State, as seen by the AC. This object is used within notifications and is not accessible.ro RbtwsRadioConfigState (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.64 |
rbtwsApConnectSecurityTypeIndicates the security level of the connection between AP and AC. This object is used within notifications and is not accessible.ro RbtwsApConnectSecurityType (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.65 |
rbtwsApServiceAvailabilityIndicates the level of wireless service availability. This object is used within notifications and is not accessible.ro RbtwsApServiceAvailability (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.66 |
rbtwsApWasOperationalIndicates whether the AP was operational before a transition occured. This object is used within notifications and is not accessible.ro RbtwsApWasOperational (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.67 |
rbtwsClientTimeSinceLastRoamThe time in seconds since the most recent roam of a given client. This object is used within notifications and is not accessible.ro Unsigned32 .1.3.6.1.4.1.52.4.15.1.2.68 |
rbtwsClientIpAddrChangeReasonIndicates the reason why client IP address changed. This object is used within notifications and is not accessible.ro RbtwsClientIpAddrChangeReason .1.3.6.1.4.1.52.4.15.1.2.69 |
rbtwsRFDetectRogueAPMacAddrDescribes the MAC address of the Rogue AP the transmitter is connected to. This object is used within notifications and is not accessible.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.52.4.15.1.2.70 |
rbtwsBlacklistingRemainingTimeThe time in seconds remaining until a given transmitter could be removed from the Black List. This object is used within notifications and is not accessible.ro Unsigned32 .1.3.6.1.4.1.52.4.15.1.2.71 |
rbtwsBlacklistingCauseIndicates the reason why a given transmitter is blacklisted. This object is used within notifications and is not accessible.ro RbtwsBlacklistingCause .1.3.6.1.4.1.52.4.15.1.2.72 |
rbtwsNumLicensedActiveAPsIndicates the maximum (licensed) number of active APs for this AC. This object is used within notifications and is not accessible.ro Unsigned32 .1.3.6.1.4.1.52.4.15.1.2.73 |
rbtwsClientDynAuthorClientIpThe dynamic authorization client IP address which caused the change of authorization. This object is used within notifications and is not accessible.ro IpAddress .1.3.6.1.4.1.52.4.15.1.2.74 |
rbtwsChangedUserParamOldValuesA display string listing the changed AAA attributes and their values, before the change of authorization was executed. This object is used within notifications and is not accessible.ro RbtwsUserAttributeList .1.3.6.1.4.1.52.4.15.1.2.75 |
rbtwsChangedUserParamNewValuesA display string listing the changed AAA attributes and their values, after the change of authorization was executed. This object is used within notifications and is not accessible.ro RbtwsUserAttributeList .1.3.6.1.4.1.52.4.15.1.2.76 |
rbtwsClientDisconnectSourceThe external source that initiated the termination of a session. This object is used within notifications and is not accessible.ro RbtwsSessionDisconnectType .1.3.6.1.4.1.52.4.15.1.2.77 |
rbtwsClientDisconnectDescriptionDisplay string for providing available information related to the external source that initiated a session termination. This object is used within notifications and is not accessible.ro DisplayString .1.3.6.1.4.1.52.4.15.1.2.78 |
rbtwsMobilityDomainSecondarySeedIpThe secondary seed IP address to which the Mobility Domain has failed over. This object is used within notifications and is not accessible.ro IpAddress .1.3.6.1.4.1.52.4.15.1.2.79 |
rbtwsMobilityDomainPrimarySeedIpThe primary seed IP address to which the Mobility Domain has failed back. This object is used within notifications and is not accessible.ro IpAddress .1.3.6.1.4.1.52.4.15.1.2.80 |
rbtwsRFDetectClassificationReasonIndicates the reason why a RF device is classified the way it is. This object is used within notifications and is not accessible.ro RbtwsRFDetectClassificationReason (RBTWS-RF-DETECT-TC) .1.3.6.1.4.1.52.4.15.1.2.81 |
rbtwsConfigSaveFileNameDisplay string listing the name of the file to which the running configuration was saved. This object is used within notifications and is not accessible.ro DisplayString .1.3.6.1.4.1.52.4.15.1.2.82 |
rbtwsConfigSaveInitiatorTypeIndicates the source that initiated a configuration save. This object is used within notifications and is not accessible.ro RbtwsConfigSaveInitiatorType .1.3.6.1.4.1.52.4.15.1.2.83 |
rbtwsConfigSaveInitiatorIpThe IP address of the source that initiated a configuration save. This object is used within notifications and is not accessible.ro IpAddress .1.3.6.1.4.1.52.4.15.1.2.84 |
rbtwsConfigSaveInitiatorDetailsDisplay string listing additional information regarding the source that initiated a configuration save, when available. This object is used within notifications and is not accessible.ro DisplayString .1.3.6.1.4.1.52.4.15.1.2.85 |
rbtwsConfigSaveGenerationIndicates the number of configuration changes since the last system boot. The generation count is used to track the number of times the running configuration has been changed due to administrative actions (set/clear), SNMP requests (SET), XML requests (e.g. RASM). This object is used within notifications and is not accessible.ro Counter32 .1.3.6.1.4.1.52.4.15.1.2.86 |
rbtwsApNumThe administratively assigned AP Number, unique on same AC (switch), regardless of how APs are attached to the AC. This object is used within notifications and is not accessible. Obsoletes rbtwsApPortOrDapNum. For clarity, use this object to identify an AP since in 6.0 directly attached APs and DAPs were unified.ro RbtwsApNum (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.87 |
rbtwsRadioModeIndicates the administratively controlled Radio Mode (enabled/disabled/sentry). This object is used within notifications and is not accessible.ro RbtwsRadioMode (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.88 |
rbtwsMichaelMICFailureCauseIndicates the Michael MIC Failure cause / who detected it. This object is used within notifications and is not accessible.ro RbtwsMichaelMICFailureCause .1.3.6.1.4.1.52.4.15.1.2.89 |
rbtwsClientAccessModeThe client access mode (ap, wired). This object is used within notifications and is not accessible. Intended to replace rbtwsClientAccessType. (In 6.0, direct- and network-attached APs were unified.)ro RbtwsClientAccessMode (RBTWS-CLIENT-SESSION-TC) .1.3.6.1.4.1.52.4.15.1.2.90 |
rbtwsClientAuthorizationReasonIndicates the reason why client performed AAA authorization. This object is used within notifications and is not accessible.ro RbtwsClientAuthorizationReason .1.3.6.1.4.1.52.4.15.1.2.91 |
rbtwsPhysPortNumPhysical Port Number on the AC. Zero means the port is unknown or not applicable (for example, when rbtwsClientAccessMode = 'ap'). This object is used within notifications and is not accessible.ro Unsigned32 .1.3.6.1.4.1.52.4.15.1.2.92 |
rbtwsApMgrOldIpThe IP address of the AP's former primary manager switch. This object is used within notifications and is not accessible.ro IpAddress .1.3.6.1.4.1.52.4.15.1.2.93 |
rbtwsApMgrNewIpThe IP address of the AP's new primary manager switch. This address was formerly the AP's secondary backup link. This object is used within notifications and is not accessible.ro IpAddress .1.3.6.1.4.1.52.4.15.1.2.94 |
rbtwsApMgrChangeReasonIndicates the reason why the AP's primary manager changed. This object is used within notifications and is not accessible.ro RbtwsApMgrChangeReason .1.3.6.1.4.1.52.4.15.1.2.95 |
rbtwsClientClearedReasonIndicates the reason why client was cleared. This object is used within notifications and is not accessible.ro RbtwsClientClearedReason .1.3.6.1.4.1.52.4.15.1.2.96 |
rbtwsMobilityDomainResiliencyStatusIndicates the current resilient capacity status for a mobility domain. This object is used within notifications and is not accessible.ro RbtwsMobilityDomainResiliencyStatus .1.3.6.1.4.1.52.4.15.1.2.97 |
rbtwsClientSessionElapsedSecondsIndicates the time in seconds elapsed since the start of the Client Session. This object is used within notifications and is not accessible.ro Unsigned32 .1.3.6.1.4.1.52.4.15.1.2.98 |
rbtwsRadioChannelWidthIndicates the administratively controlled Channel Width (20MHz/40MHz). This object is used within notifications and is not accessible.ro RbtwsRadioChannelWidth (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.99 |
rbtwsRadioMimoStateIndicates the Radio MIMO State, as seen by the AC (1x1/2x3/3x3). This object is used within notifications and is not accessible.ro RbtwsRadioMimoState (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.100 |
rbtwsClientRadioTypeIndicates the Client Radio Type, as detected by an attached AP and reported to the AC. This object is used within notifications and is not accessible.ro RbtwsRadioType (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.101 |
rbtwsRFDetectXmtrRadioTypeIndicates the Radio Type of the Transmitter, as detected by an attached AP and reported to the AC. The Transmitter may be a wireless client or an AP. This object is used within notifications and is not accessible.ro RbtwsRadioType (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.102 |
rbtwsRFDetectXmtrCryptoTypeIndicates the Crypto Type used by the Transmitter, as detected by an attached AP and reported to the AC. This object is used within notifications and is not accessible.ro RbtwsCryptoType (RBTWS-AP-TC) .1.3.6.1.4.1.52.4.15.1.2.103 |
rbtwsClusterFailureReasonIndicates the reason why cluster configuration failed to apply. This object is used within notifications and is not accessible.ro RbtwsClusterFailureReason .1.3.6.1.4.1.52.4.15.1.2.104 |
rbtwsClusterFailureDescriptionDisplay string for describing the cluster configuration failure cause. This object is used within notifications and is not accessible.ro DisplayString .1.3.6.1.4.1.52.4.15.1.2.105 |
rbtwsTrapMibNotifications emitted by Enterasys Networks wireless switches. AP = Access Point; AC = Access Controller (wireless switch), the device that runs a SNMP Agent implementing this MIB. Copyright 2008 Enterasys Networks, Inc. All rights reserved. This SNMP Management Information Base Specification (Specification) embodies confidential and proprietary intellectual property. This Specification is supplied 'AS IS' and Enterasys Networks makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification. MODULE-IDENTITY .1.3.6.1.4.1.52.4.15.1.4.1 |
rbtwsTrapsV2 OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.15.1.5.0 |
rbtwsDeviceFailTrapThe device has a failure indication NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.1 |
rbtwsDeviceOkayTrapThe device has recovered NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.2 |
rbtwsPoEFailTrapPoE has failed on the indicated port NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.3 |
rbtwsApTimeoutTrapThe AP entering the AC at port rbtwsPortNum with MAC rbtwsRadioMacAddress and of the access type (ap or dap) has not responded. Replaced by rbtwsApNonOperStatusTrap2, with rbtwsApTransition = 'timeout'.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.4 |
rbtwsAPBootTrapThe AP entering the AC at port rbtwsPortNum with MAC rbtwsRadioMacAddress and of the access type (ap or dap) has booted. Replaced by rbtwsApNonOperStatusTrap2, with rbtwsApTransition = 'bootSuccess'.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.5 |
rbtwsMobilityDomainJoinTrapThe mobility domain member has received an UP notice from the remote address. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.6 |
rbtwsMobilityDomainTimeoutTrapThe mobility domain member has declared the remote address to be DOWN. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.7 |
rbtwsMpMichaelMICFailureTwo Michael MIC failures were seen within 60 seconds of each other. Obsoleted by rbtwsMichaelMICFailure.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.8 |
rbtwsRFDetectRogueAPTrapThis trap is sent when RF detection finds a rogue AP. XmtrMacAddr is the radio MAC address from the beacon. ListenerListInfo is a display string of a list of listener information. Obsoleted by rbtwsRFDetectRogueDeviceTrap2.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.9 |
rbtwsRFDetectAdhocUserTrapThis trap is sent when RF detection sweep finds a ad-hoc user. rbtwsRFDetectXmtrMacAddr is the MAC address of the ad-hoc user. rbtwsRFDetectListenerListInfo is a display string of a list of listener information. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.10 |
rbtwsRFDetectRogueDisappearTrapThis trap is sent when a rogue has disappeared. Obsoleted by rbtwsRFDetectRogueDeviceDisappearTrap.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.11 |
rbtwsClientAuthenticationFailureTrapThis trap is sent if a client authentication fails. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.12 |
rbtwsClientAuthorizationFailureTrapThis trap is sent if a client authorization fails. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.13 |
rbtwsClientAssociationFailureTrapThis trap is sent if a client association fails. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.14 |
rbtwsClientAuthorizationSuccessTrapThis trap is sent when a client authorizes. Obsoleted by rbtwsClientAuthorizationSuccessTrap4.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.15 |
rbtwsClientDeAssociationTrapThis trap is sent if a client de-association occurred. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.16 |
rbtwsClientRoamingTrapThis trap is sent if a client roams from one location to another. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.17 |
rbtwsAutoTuneRadioPowerChangeTrapThis trap is sent if a radio's power level has changed based on auto-tune. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.18 |
rbtwsAutoTuneRadioChannelChangeTrapThis trap is sent if a radio's channel has changed based on auto-tune. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.19 |
rbtwsCounterMeasureStartTrapThis trap is sent when counter measures are started against a rogue. rbtwsRFDetectXmtrMacAddr is the mac address of the rogue we are doing counter measures against. rbtwsRadioMACAddress identifies the radio performing the countermeasures. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.20 |
rbtwsCounterMeasureStopTrapThis trap is sent when counter measures are stopped against a rogue. rbtwsRFDetectXmtrMacAddr is the mac address of the rogue we were doing counter measures against. rbtwsRadioMACAddress identifies the radio performing the countermeasures. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.21 |
rbtwsClientDot1xFailureTrapThis trap is sent if a client failed 802.1X. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.22 |
rbtwsClientClearedTrapThis trap is sent when a client session is cleared. Obsoleted by rbtwsClientClearedTrap2.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.23 |
rbtwsClientAuthorizationSuccessTrap2This trap is sent when a client authorizes. Obsoleted by rbtwsClientAuthorizationSuccessTrap4.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.24 |
rbtwsRFDetectSpoofedMacAPTrapThis trap is sent when RF detection finds an AP using the MAC of the listener. rbtwsRFDetectXmtrMacAddr is the radio MAC address from the beacon. rbtwsRFDetectListenerListInfo is a display string of a list of listener information. Obsoleted by rbtwsRFDetectDoSTrap and rbtwsRFDetectRogueDeviceTrap2. One of the two traps will be sent depending on the type of AP MAC spoofing detected.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.25 |
rbtwsRFDetectSpoofedSsidAPTrapThis trap is sent when RF detection finds an AP using the SSID of the listener, and the AP is not in the mobility domain. rbtwsRFDetectXmtrMacAddr is the radio MAC address from the beacon. rbtwsRFDetectListenerListInfo is a display string of a list of listener information. Obsoleted by rbtwsRFDetectRogueDeviceTrap2 and rbtwsRFDetectSuspectDeviceTrap2. One of the two traps will be sent, depending on RF detection classification rules.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.26 |
rbtwsRFDetectDoSTrapThis trap is sent when RF detection finds a denial of service (DoS) occurring. rbtwsRFDetectDoSType specifies the type of DoS. rbtwsRFDetectXmtrMacAddr is the radio MAC address from the beacon. rbtwsRFDetectListenerListInfo is a display string of a list of listener information. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.27 |
rbtwsRFDetectClientViaRogueWiredAPTrapThis trap is sent when a client is detected that connected via a rogue AP that is attached to a wired port. rbtwsSourceWsIp is the IP address of the AC (switch) with the wired port. rbtwsPortNum is the port on the AC. rbtwsClientVLANid is the VLAN ID of the client's traffic. rbtwsClientVLANtag is the VLAN tag of the client's traffic. rbtwsRFDetectXmtrMacAddr is the MAC address of the client. rbtwsRFDetectListenerListInfo is a display string of a list of listener information. Obsoleted by rbtwsRFDetectClientViaRogueWiredAPTrap3.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.28 |
rbtwsRFDetectInterferingRogueAPTrapThis trap is sent when RF detection finds an interfering rogue AP. rbtwsRFDetectXmtrMacAddr is the radio MAC address from the beacon. rbtwsRFDetectListenerListInfo is a display string of a list of listener information. Obsoleted by rbtwsRFDetectSuspectDeviceTrap2.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.29 |
rbtwsRFDetectInterferingRogueDisappearTrapThis trap is sent when an interfering rogue has disappeared. rbtwsRFDetectXmtrMacAddr is the radio MAC address from the beacon. Obsoleted by rbtwsRFDetectSuspectDeviceDisappearTrap.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.30 |
rbtwsRFDetectUnAuthorizedSsidTrapThis trap is sent when RF detection finds use of an unauthorized SSID. rbtwsRFDetectXmtrMacAddr is the radio MAC address from the beacon. rbtwsRFDetectListenerListInfo is a display string of a list of listener information. Obsoleted by rbtwsRFDetectRogueDeviceTrap2 and rbtwsRFDetectSuspectDeviceTrap2. One of the two traps will be sent if the device having an unauthorized SSID is classified as rogue or suspect because of this.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.31 |
rbtwsRFDetectUnAuthorizedOuiTrapThis trap is sent when RF detection finds use of an unauthorized OUI. rbtwsRFDetectXmtrMacAddr is the radio MAC address from the beacon. rbtwsRFDetectListenerListInfo is a display string of a list of listener information. Obsoleted by rbtwsRFDetectRogueDeviceTrap2 and rbtwsRFDetectSuspectDeviceTrap2. One of the two traps will be sent if the device having an unauthorized OUI is classified as rogue or suspect because of this.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.32 |
rbtwsRFDetectUnAuthorizedAPTrapThis trap is sent when RF detection finds operation of an unauthorized AP. rbtwsRFDetectXmtrMacAddr is the radio MAC address from the beacon. rbtwsRFDetectListenerListInfo is a display string of a list of listener information. Obsoleted by rbtwsRFDetectRogueDeviceTrap2.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.33 |
rbtwsDAPConnectWarningTrapA DAP, tried to connect to the AC. rbtwsDeviceModel provides the model of the DAP. rbtwsDeviceSerNum provides the serial number of the DAP. rbtwsRsaPubKeyFingerPrint provides the computed fingerprint of the DAP. rbtwsDAPconnectWarningType provides the type of connect warning. Replaced by rbtwsApNonOperStatusTrap2, with rbtwsApTransition = 'connectFail'.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.34 |
rbtwsRFDetectDoSPortTrapThis trap is sent when RF detection finds a denial of service (DoS) occurring. This has port and AP info instead of 'Listener info'. rbtwsRFDetectDoSType specifies the type of DoS. rbtwsRFDetectXmtrMacAddr is the radio MAC address from the beacon. rbtwsClientAccessType specifies whether wired, AP, or DAP. rbtwsPortNum (for wired or AP), the port that is used. rbtwsDAPNum (for a DAP), the ID of the DAP. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.35 |
rbtwsMpMichaelMICFailure2Two Michael MIC failures were seen within 60 seconds of each other. Object rbtwsClientMACAddress is the source of the first failure, and object rbtwsClientMACAddress2 source of the second failure. Obsoleted by rbtwsMichaelMICFailure.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.36 |
rbtwsApNonOperStatusTrapThis trap is sent when the AP changes state and the new one is a non-operational state. Obsoleted by rbtwsApNonOperStatusTrap2.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.37 |
rbtwsApOperRadioStatusTrapThis trap is sent when the Radio changes state. It also contains aggregate information about the AP in operational state - security level and service availability. Obsoleted by rbtwsApOperRadioStatusTrap3.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.38 |
rbtwsClientIpAddrChangeTrapThis trap is sent when a client's IP address changes. The most likely case for this is when the client first connects to the network. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.39 |
rbtwsClientAssociationSuccessTrapThis trap is sent if a client association succeeds. WARNING: DO NOT enable it in normal use. It may impair switch performance! Only recommended for debugging network issues. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.40 |
rbtwsClientAuthenticationSuccessTrapThis trap is sent if a client authentication succeeds. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.41 |
rbtwsClientDeAuthenticationTrapThis trap is sent if a client de-authentication occured. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.42 |
rbtwsRFDetectBlacklistedTrapThis trap is sent if an association, re-association or de-association request (packet) is detected from a blacklisted transmitter (identified by MAC: 'rbtwsRFDetectXmtrMacAddr'). If 'rbtwsBlacklistingCause' is 'configured', then 'rbtwsBlacklistingRemainingTime' will be zero, meaning indefinite time (depending on administrative actions on the Black List). Otherwise, 'rbtwsBlacklistingRemainingTime' will indicate the time in seconds until this transmitter's requests could be allowed. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.43 |
rbtwsRFDetectClientViaRogueWiredAPTrap2This trap is sent when a client is detected that connected via a rogue AP that is attached to a wired port. rbtwsSourceWsIp is the IP address of the AC (switch) with the wired port. rbtwsPortNum is the port on the AC. rbtwsClientVLANid is the VLAN ID of the client's traffic. rbtwsClientVLANtag is the VLAN tag of the client's traffic. rbtwsRFDetectXmtrMacAddr is the MAC address of the client. rbtwsRFDetectListenerListInfo is a display string of a list of listener information. rbtwsRFDetectRogueAPMacAddr is the MAC address of the Rogue AP (wired) the client is connected to. Obsoleted by rbtwsRFDetectClientViaRogueWiredAPTrap3.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.44 |
rbtwsRFDetectAdhocUserDisappearTrapThis trap is sent when RF detection sweep finds that an ad-hoc user disappeared. rbtwsRFDetectXmtrMacAddr is the MAC address of the ad-hoc user. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.45 |
rbtwsApRejectLicenseExceededTrapThis trap is sent when an AC (wireless switch) receives a packet from an inactive AP and attaching that AP would make the AC exceed the maximum (licensed) number of active APs. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.46 |
rbtwsClientDynAuthorChangeSuccessTrapThis trap is sent when the authorization attributes for a user are dynamically changed by an authorized dynamic authorization client. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.47 |
rbtwsClientDynAuthorChangeFailureTrapThis trap is sent if a change of authorization request sent by an authorized dynamic authorization client is unsuccessful. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.48 |
rbtwsClientDisconnectTrapThis trap is sent when a client session is terminated administratively. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.49 |
rbtwsMobilityDomainFailOverTrapThis trap is sent when the Mobility Domain fails over to the secondary seed. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.50 |
rbtwsMobilityDomainFailBackTrapThis trap is sent when the Mobility Domain fails back to the primary seed. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.51 |
rbtwsRFDetectRogueDeviceTrapThis trap is sent when RF detection finds a rogue device. XmtrMacAddr is the radio MAC address from the beacon. ListenerListInfo is a display string of a list of listener information. ClassificationReason indicates the reason why the device is classified as rogue. Obsoleted by rbtwsRFDetectRogueDeviceTrap2.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.52 |
rbtwsRFDetectRogueDeviceDisappearTrapThis trap is sent when a rogue device has disappeared. This trap obsoletes the rbtwsRFDetectRogueDisappearTrap. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.53 |
rbtwsRFDetectSuspectDeviceTrapThis trap is sent when RF detection finds a suspect device. rbtwsRFDetectXmtrMacAddr is the radio MAC address from the beacon. rbtwsRFDetectListenerListInfo is a display string of a list of listener information. ClassificationReason indicates the reason why the device is classified as suspect. Obsoleted by rbtwsRFDetectSuspectDeviceTrap2.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.54 |
rbtwsRFDetectSuspectDeviceDisappearTrapThis trap is sent when a suspect device has disappeared. rbtwsRFDetectXmtrMacAddr is the radio MAC address from the beacon. This trap obsoletes the rbtwsRFDetectInterferingRogueDisappearTrap. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.55 |
rbtwsRFDetectClientViaRogueWiredAPTrap3This trap is sent when a client is detected that connected via a rogue AP that is attached to a wired port. rbtwsSourceWsIp is the IP address of the AC (switch) with the wired port. rbtwsPortNum is the port on the AC. rbtwsClientVLANid is the VLAN ID of the client's traffic. rbtwsClientVLANtag is the VLAN tag of the client's traffic. rbtwsRFDetectXmtrMacAddr is the MAC address of the client. rbtwsRFDetectListenerListInfo is a display string of a list of listener information. rbtwsRFDetectRogueAPMacAddr is the MAC address of the Rogue AP (wired) the client is connected to. ClassificationReason indicates the reason why the AP is classified as rogue. This trap obsoletes the rbtwsRFDetectClientViaRogueWiredAPTrap and rbtwsRFDetectClientViaRogueWiredAPTrap2. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.56 |
rbtwsRFDetectClassificationChangeTrapThis trap is sent when RF detection classification rules change. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.57 |
rbtwsConfigurationSavedTrapThis trap is sent when the running configuration of the switch is written to a configuration file. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.58 |
rbtwsApNonOperStatusTrap2This trap is sent when the AP changes state and the new one is a non-operational state. Obsoletes rbtwsApNonOperStatusTrap. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.59 |
rbtwsApOperRadioStatusTrap2This trap is sent when the Radio changes state. It also contains aggregate information about the AP in operational state - security level and service availability. Obsoleted by rbtwsApOperRadioStatusTrap3.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.60 |
rbtwsMichaelMICFailureTwo Michael MIC failures were seen within 60 seconds of each other. Object rbtwsClientMACAddress indicates the source of the first failure, and object rbtwsClientMACAddress2 indicates the source of the second failure. Service is interrupted for 60 seconds on the radio due to TKIP countermeasures having commenced. The radio is identified by rbtwsApNum and rbtwsAPRadioNum. An alternative way to identify the radio is rbtwsRadioMACAddress. Obsoletes rbtwsMpMichaelMICFailure and rbtwsMpMichaelMICFailure2. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.61 |
rbtwsClientAuthorizationSuccessTrap3This trap is sent when a client authorizes. If rbtwsClientAccessMode = 'ap': rbtwsApNum, rbtwsAPRadioNum, rbtwsRadioSSID identify the AP/radio/BSS providing wireless service to this client at the time this trap was sent. If rbtwsClientAccessMode = 'wired': rbtwsPhysPortNum identifies the physical port on the AC used by this wired-auth client. Obsoleted by rbtwsClientAuthorizationSuccessTrap4.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.62 |
rbtwsApManagerChangeTrapThis trap is sent when the AP's secondary link becomes its primary link. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.63 |
rbtwsClientClearedTrap2This trap is sent when a client session is cleared. Obsoletes rbtwsClientClearedTrap. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.64 |
rbtwsMobilityDomainResiliencyStatusTrapThis trap is sent by a mobility domain seed to announce changes in resilient capacity status. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.65 |
rbtwsApOperRadioStatusTrap3This trap is sent when the Radio changes state. It also contains aggregate information about the AP in operational state - security level and service availability. Obsoletes rbtwsApOperRadioStatusTrap and rbtwsApOperRadioStatusTrap2. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.66 |
rbtwsClientAuthorizationSuccessTrap4This trap is sent when a client authorizes. If rbtwsClientAccessMode = 'ap': rbtwsApNum, rbtwsAPRadioNum, rbtwsRadioSSID identify the AP/radio/BSS providing wireless service to this client at the time this trap was sent; rbtwsClientRadioType gives the type of radio used by this client. If rbtwsClientAccessMode = 'wired': rbtwsPhysPortNum identifies the physical port on the AC used by this wired-auth client. Obsoletes rbtwsClientAuthorizationSuccessTrap, rbtwsClientAuthorizationSuccessTrap2, rbtwsClientAuthorizationSuccessTrap3. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.67 |
rbtwsRFDetectRogueDeviceTrap2This trap is sent when RF detection finds a rogue device. rbtwsRFDetectXmtrMacAddr is the radio MAC address from the beacon. rbtwsRFDetectXmtrRadioType indicates the Type of Radio used by the transmitter (rogue device). rbtwsRFDetectXmtrCryptoType indicates the Type of Crypto used by the transmitter (rogue device). rbtwsRFDetectListenerListInfo is a display string of a list of listener information. rbtwsRFDetectClassificationReason indicates the reason why the device is classified as rogue. Obsoletes rbtwsRFDetectRogueAPTrap, rbtwsRFDetectUnAuthorizedAPTrap, rbtwsRFDetectRogueDeviceTrap. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.68 |
rbtwsRFDetectSuspectDeviceTrap2This trap is sent when RF detection finds a suspect device. rbtwsRFDetectXmtrMacAddr is the radio MAC address from the beacon. rbtwsRFDetectXmtrRadioType indicates the Type of Radio used by the transmitter (suspect device). rbtwsRFDetectXmtrCryptoType indicates the Type of Crypto used by the transmitter (suspect device). rbtwsRFDetectListenerListInfo is a display string of a list of listener information. rbtwsRFDetectClassificationReason indicates the reason why the device is classified as suspect. Obsoletes rbtwsRFDetectInterferingRogueAPTrap, rbtwsRFDetectSuspectDeviceTrap. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.69 |
rbtwsClusterFailureTrapThis trap is sent when the cluster configuration failed to apply. If rbtwsClusterFailureReason = 'validation-error': The validation error is reported by the receiving end of the configuration updates. The receiving end can be any AC (switch) in the mobility domain: member, secondary seed or primary seed. - Primary seed will be the receiving end of configuration updates when Primary seed is joining the cluster and Secondary seed has preempt mode enabled. - Both Secondary seed and member will be at the receiving end when Primary seed is active. NOTIFICATION-TYPE .1.3.6.1.4.1.52.4.15.1.5.0.70 |