RADLAN-Physicaldescription-MIB
AI MIB Summary
The RADLAN-Physicaldescription-MIB provides vendor-specific access to the physical layer configuration parameters of RAD Data Communications networking hardware, specifically exposing interface attributes such as port status, media type, and physical link characteristics for device management.
The private MIB module definition for physical device configuration.
Main OID:
rlPhysicalDescription.1.3.6.1.4.1.89.53
99
Objects
Active
Status
9
Dependencies
Imported Objects
Objects
99 total| Object Name |
|---|
rlStackUnitRemovedTrap indicating that a unit was removed from the stack. NOTIFICATION-TYPE .1.3.6.1.4.1.89.0.186 |
rlStackConfigChangedRingChainTrap indicating that the configuration of the stack has changed.
- from ring to chain
- from chain to ring. NOTIFICATION-TYPE .1.3.6.1.4.1.89.0.187 |
rlStackBackupUnitRemovedTrap indicating that the backup unit was removed from the stack. NOTIFICATION-TYPE .1.3.6.1.4.1.89.0.188 |
rlStackMasterSwitchoverTrap indicating that a new master was elected.
The old maste is the backup now. NOTIFICATION-TYPE .1.3.6.1.4.1.89.0.189 |
rlStackUnitDifferentSwVersionTrap indicating that the new unit added to the stack has
different software version than the master. NOTIFICATION-TYPE .1.3.6.1.4.1.89.0.190 |
rlStackDuplicateUnitNotJoinTrap indicating that a new unit with duplicated unit id was
added to the stack - but it will not join the stack. NOTIFICATION-TYPE .1.3.6.1.4.1.89.0.191 |
rlStackLinkChangeTrap indicating that Link has change in one of the Stacking Ports. NOTIFICATION-TYPE .1.3.6.1.4.1.89.0.195 |
rlPhysicalDescriptionThe private MIB module definition for physical
device configuration. MODULE-IDENTITY .1.3.6.1.4.1.89.53 |
IMPORTSThe private MIB module definition for physical
device configuration. Unknown .1.3.6.1.4.1.89.53 |
rlPhdMibVersionMIB's version, the current version is 3.
1: original version
2: a. new tables
rlPhdModuleHotSwapTable
rlPhdStackOrderTable
b. new scalars
rlPhdStackReorder
rlPhdNumberOfUnits
rlPhdMaxNumberOfUnits
3: a. new field rlPhdModuleRole of rlPhdModuleTable
b. new scalars
rlPhdForceMasterUnit
4: a. new fields rlPhdModuleConnect1 and rlPhdModuleConnect2
of rlPhdModuleTable.
5: a. Prefix rlPhD were replaced by prefix rlPhd
b. fields rlPhdModuleConnect1 and rlPhdModuleConnect2 are
moved from rlPhdModuleTable to rlPhdStackTable.
c. new fiels rlPhdStackSofrwareVer, rlPhdStackProductID and
rlPhdStackMacAddr of rlPhdStackTable.
d. new scalars
rlPhdStackReloadUnit
e. new scalars
rlPhdStackOrderTopUnit
rlPhdStackOrderBottomUnit
rlPhdStackOrderPermutationro INTEGER .1.3.6.1.4.1.89.53.1 |
rlPhdModuleTableFor each module (board) there is an entry describing it in this
module SEQUENCE OF RlPhdModuleEntry .1.3.6.1.4.1.89.53.2 |
rlPhdModuleEntryA entry of this table specifies a module (board) RlPhdModuleEntry .1.3.6.1.4.1.89.53.2.1 |
rlPhdModuleStackUnitThe stack unit to which this module belongs.ro INTEGER .1.3.6.1.4.1.89.53.2.1.1 |
rlPhdModuleIndexThe number of the module in its stack unitro INTEGER .1.3.6.1.4.1.89.53.2.1.2 |
rlPhdModuleTypeThe module type:
1 - unknown
2 - extension
3 - acceleratorOpal
4 - acceleratorHertz3
5 - acceleratorUhual3
6 - hertz2
7 - uhual2
8 - hertz3
9 - uhual3ge
10 - uhual3sonet
11 - uhual3atm
12 - bcm2402
13 - lg8-0
14 - lg16-0
15 - lg8-1
16 - hertz2plus
17 - uhual2plus
18 - 2 98MX620
19 - 2 98EX120
20 - 1 98EX110
21 - two herz3 copper
22 - two uhaul3 fiber SX
23 - two uhaul3 copper
24 - hertz3 fiber
25 - two uhaul3 gibic
26 - two herz3 fiber
27 - two uhaul3 fiber LX
28 - bcm5615 stackable 24
29 - bcm5625x2 stackable 48
30 - EX125D-24 Giga ports
31 - EX115D-48 Fast 4 Giga
32 - SICC 4 copper ports
33 - SICC 4 fiber ports
34 - SICC gbic ports
35 - VesuvioT
36 - VesuvioF
37 - 98DX160
38 - 98DX240
39 - 98DX162
40 - 98DX242
41 - Gemstones Sapphire only
42 - Gemstones 24F+4G
43 - Gemstones 48F+4G
44 - Cheetah 24G + 3XG
45 - Cheetah 48G stacking
46 - Gemstones Sapphire only with PoE
47 - Gemstones 24F+4G with PoE
48 - Gemstones 48F+4G with PoE
49 - DLink DXS3250
50 - DLink DXS3227
51 - DLink DXS3227 with PoE
52 - Alcatel 24F+4G Non PoE
53 - Alcatel 48F+4G Non PoE
54 - Alcatel 24F+4G with PoE
55 - Alcatel 48F+4G with PoE
56 - HP Diamond 40F + 4G
57 - Cheetah cut 98DX163 16G + 2XG
58 - Cheetah cut 98DX243 24G + 2XG
59 - Diamond 8F
60 - Diamond 8F POE
61 - Diamond 8F MaxPower POE
62 - Diamond 8F 2G (copper + LC)
63 - Diamond 8F 2G
64 - Diamond 8G
65 - Diamond 8G POE
66 - Diamond 8G MaxPower POEro INTEGER .1.3.6.1.4.1.89.53.2.1.3 |
rlPhdModuleStartingPortThe minimal number of the port residing on this module.ro INTEGER .1.3.6.1.4.1.89.53.2.1.4 |
rlPhdModuleNumberOfPortsThe number of ports residing on this module.ro INTEGER .1.3.6.1.4.1.89.53.2.1.5 |
rlPhdModuleRowOn which row (the uppermost being numbered 1 and the highest row
number asigned to the lowest row) this module resides within the
chassis of its stack unit.ro INTEGER .1.3.6.1.4.1.89.53.2.1.6 |
rlPhdModuleColumnOn which column (the leftmost being numbered 1 and the highest column
number asigned to the rightmost column) this module resides within the
chassis of its stack unit.ro INTEGER .1.3.6.1.4.1.89.53.2.1.7 |
rlPhdModuleRoleThe module role in the stack.ro Enumeration .1.3.6.1.4.1.89.53.2.1.8 |
rlPhdPortsTableLists the physical or physical-related attributes of ports SEQUENCE OF RlPhdPortsEntry .1.3.6.1.4.1.89.53.3 |
rlPhdPortsEntryFor each port, a entry describing attributes which are either
physical or are derived from the features of the device hardware RlPhdPortsEntry .1.3.6.1.4.1.89.53.3.1 |
rlPhdPortsIfIndexThe L2 interface number associated with this port.ro INTEGER .1.3.6.1.4.1.89.53.3.1.1 |
rlPhdPortsIfIndexNameThe L2 interface number associated with this port, in string format
based on the overall hardware architecture of the device (i.e., for
monolithic devices just numbers, devices composed of modules (boards,
cards) or stackable devices composed of monolithic units in form
<module /stack unit number> - <port number on current module /stack
unit number>, stackable devices in which each unit is composed of
modules
<stack unit number> - <module number> - <port number>ro DisplayString .1.3.6.1.4.1.89.53.3.1.2 |
rlPhdPortsMediaTypeThe media type of this port.ro Enumeration .1.3.6.1.4.1.89.53.3.1.3 |
rlPhdPortsStackUnitThe number of the slot to which this port belongs.ro INTEGER .1.3.6.1.4.1.89.53.3.1.4 |
rlPhdPortsModuleNumberThe number of the stack unit to which this port resides in.ro INTEGER .1.3.6.1.4.1.89.53.3.1.5 |
rlPhdPortsRowOn which row (the uppermost being numbered 1 and the highest row
number asigned to the lowest row) this port resides within its
module.ro INTEGER .1.3.6.1.4.1.89.53.3.1.6 |
rlPhdPortsColumnOn which column (the leftmost being numbered 1 and the highest column
number asigned to the rightmost column) this this port resides within its
module.ro INTEGER .1.3.6.1.4.1.89.53.3.1.7 |
rlPhdConnectorTypeType of connector.ro JackType .1.3.6.1.4.1.89.53.3.1.8 |
rlPhdPortHaulDistance supported by this port.ro Enumeration .1.3.6.1.4.1.89.53.3.1.9 |
rlPhdStackTableFor each stack unit there is an entry describing it in this table SEQUENCE OF RlPhdStackEntry .1.3.6.1.4.1.89.53.4 |
rlPhdStackEntryA entry of this table specifies a stack unit RlPhdStackEntry .1.3.6.1.4.1.89.53.4.1 |
rlPhdStackUnitThe stack unit described by this entry.ro INTEGER .1.3.6.1.4.1.89.53.4.1.1 |
rlPhdStackTypeThe type of the stack unit described by this entry:
1 - box 3202
2 - box LG
3 - bcm
4 - presteraro INTEGER .1.3.6.1.4.1.89.53.4.1.2 |
rlPhdStackConnect1The unit number connected to the Hyper GLink left side connection -
0 means not connected; other integer indicates the unit number.ro INTEGER .1.3.6.1.4.1.89.53.4.1.3 |
rlPhdStackConnect2The unit number connected to the Hyper GLink right side connection -
0 means not connected; other integer indicates the unit number.ro INTEGER .1.3.6.1.4.1.89.53.4.1.4 |
rlPhdStackSofrwareVerThe Software version of the unit.ro DisplayString .1.3.6.1.4.1.89.53.4.1.5 |
rlPhdStackProductIDThe Product ID of the unit.ro DisplayString .1.3.6.1.4.1.89.53.4.1.6 |
rlPhdStackMacAddrThe physical (MAC) address of the unit.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.89.53.4.1.7 |
rlPhdModuleHotSwapTableFor each module (board) there is an entry describing its Hot Swap
status SEQUENCE OF RlPhdModuleHotSwapEntry .1.3.6.1.4.1.89.53.5 |
rlPhdModuleHotSwapEntryA entry of this table specifies a module (board) Hot Swap
status RlPhdModuleHotSwapEntry .1.3.6.1.4.1.89.53.5.1 |
rlPhdModuleHotSwapAdminStatusThe desired state of the module. The off(1) state indicates
that the module is not used and its rlPhdModuleHotSwapOperStatus
is always off(2).
The on{1) state indicates that the module may be used and its
rlPhdModuleHotSwapOperStatus will be on(1) if it presents and
off(2) if it does not present.rw Enumeration .1.3.6.1.4.1.89.53.5.1.1 |
rlPhdModuleHotSwapOperStatusThe current Hot Swap state of the module.
If rlPhdModuleHotSwapAdminStatus is down(2) then
rlPhdModuleHotSwapOperStatus should be down(2). If
rlPhdModuleHotSwapAdminStatus is changed to up(1) then
rlPhdModuleHotSwapOperStatus should change to
up(1) if the module presents; it should remain in the down(2) state if
and only if the module does not present.ro Enumeration .1.3.6.1.4.1.89.53.5.1.2 |
rlPhdStackOrderTableThis table enables the user to configure the order
of the stack units as displayed on his GUI.
The order of the entries in this table corresponds
to the last configured order. If the stack units order was
never configured, the order will be the same as in the rlPhdStackTable. SEQUENCE OF RlPhdStackOrderEntry .1.3.6.1.4.1.89.53.6 |
rlPhdStackOrderEntryA entry of this table specifies a stack unit in the position desired by the user RlPhdStackOrderEntry .1.3.6.1.4.1.89.53.6.1 |
rlPhdStackOrderCurrentUnitPositionThe current stack unit position. INTEGER .1.3.6.1.4.1.89.53.6.1.1 |
rlPhdStackOrderDesiredUnitPositionThe desired stack unit position. Note that setting this MIB
object will take effect only after setting the rlPhdStackReorder MIB
object below. After setting this MIB object and until a further change
of at least one instance of the rlPhdStackOrderDesiredUnitPosition object,
the values of the rlPhdStackOrderCurrentUnitPosition objectinstance and
the corresponding rlPhdStackOrderDesiredUnitPosition object instance
will be the same.rw INTEGER .1.3.6.1.4.1.89.53.6.1.2 |
rlPhdStackOrderUnitIndexThis is the original unit index, i.e. has the same value as rlPhdStackUnit
above. INTEGER .1.3.6.1.4.1.89.53.6.1.3 |
rlPhdStackOrderUnitTypeThe type of the stack unit described by this entry. It has the same value
as rlPhdStackType above. This information is duplicated here only for easier
retrieval by the device manager.ro INTEGER .1.3.6.1.4.1.89.53.6.1.4 |
rlPhdStackReorderSetting this MIB object will cause the settings of the
rlPhdStackOrderDesiredUnitPosition MIB object instances to take effect.
After setting this MIB object and until a further change
of at least one instance of the rlPhdStackOrderDesiredUnitPosition object,
the values of the rlPhdStackOrderCurrentUnitPosition objectinstance and
the corresponding rlPhdStackOrderDesiredUnitPosition object instance
will be the same.rw Enumeration .1.3.6.1.4.1.89.53.7 |
rlPhdNumberOfUnitsShows the current number of units in the stack.ro INTEGER .1.3.6.1.4.1.89.53.8 |
rlPhdMaxNumberOfUnitsShows the maximum number of units in the stack.ro INTEGER .1.3.6.1.4.1.89.53.9 |
rlPhdForceMasterUnitForce unit to be master.rw INTEGER .1.3.6.1.4.1.89.53.10 |
rlPhdStackFixedUnitDetermine which unit will be on bottom/top of list
on Show-List command(see .rw INTEGER .1.3.6.1.4.1.89.53.11 |
rlPhdStackFixedUnitLocationDetermine the bottom/top object in the stack table.rw Enumeration .1.3.6.1.4.1.89.53.12 |
rlPhdStackReloadUnitReset a specific unit.rw INTEGER .1.3.6.1.4.1.89.53.13 |
rlPhdUnitGenParamTableFor each module (board) there is an entry describing it in this
module SEQUENCE OF RlPhdUnitGenParamEntry .1.3.6.1.4.1.89.53.14 |
rlPhdUnitGenParamEntryA entry of this table specifies a module (board) RlPhdUnitGenParamEntry .1.3.6.1.4.1.89.53.14.1 |
rlPhdUnitGenParamStackUnitThe index of the stack unit to which this conceptual row corresponds.
Note that the index will be the same index as the index
of a 'chassis' physical entity in the entity MIB of the product.ro INTEGER .1.3.6.1.4.1.89.53.14.1.1 |
rlPhdUnitGenParamSoftwareVersionSerial number of the product.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.89.53.14.1.2 |
rlPhdUnitGenParamFirmwareVersionSerial number of the product.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.89.53.14.1.3 |
rlPhdUnitGenParamHardwareVersionSerial number of the product.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.89.53.14.1.4 |
rlPhdUnitGenParamSerialNumSerial number of the product.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.89.53.14.1.5 |
rlPhdUnitGenParamAssetTagSerial number of the product.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.89.53.14.1.6 |
rlPhdUnitGenParamServiceTagAsset tag of the product.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.89.53.14.1.7 |
rlPhdUnitEnvParamTableFor each module (board) there is an entry describing it in this
module SEQUENCE OF RlPhdUnitEnvParamEntry .1.3.6.1.4.1.89.53.15 |
rlPhdUnitEnvParamEntryA entry of this table specifies a module (board) RlPhdUnitEnvParamEntry .1.3.6.1.4.1.89.53.15.1 |
rlPhdUnitEnvParamStackUnitThe index of the stack unit to which this conceptual row corresponds.
Note that the index will be the same index as the index
of a 'chassis' physical entity in the entity MIB of the product.ro INTEGER .1.3.6.1.4.1.89.53.15.1.1 |
rlPhdUnitEnvParamMainPSStatusThe mandatory state of the main PS being instrumented.ro RlEnvMonState (RADLAN-HWENVIROMENT) .1.3.6.1.4.1.89.53.15.1.2 |
rlPhdUnitEnvParamRedundantPSStatusThe mandatory state of the redundant PS being instrumented.ro RlEnvMonState (RADLAN-HWENVIROMENT) .1.3.6.1.4.1.89.53.15.1.3 |
rlPhdUnitEnvParamFan1StatusThe mandatory state of the FAN 1 being instrumented.ro RlEnvMonState (RADLAN-HWENVIROMENT) .1.3.6.1.4.1.89.53.15.1.4 |
rlPhdUnitEnvParamFan2StatusThe mandatory state of the FAN 2 being instrumented.ro RlEnvMonState (RADLAN-HWENVIROMENT) .1.3.6.1.4.1.89.53.15.1.5 |
rlPhdUnitEnvParamFan3StatusThe mandatory state of the FAN 3 being instrumented.ro RlEnvMonState (RADLAN-HWENVIROMENT) .1.3.6.1.4.1.89.53.15.1.6 |
rlPhdUnitEnvParamFan4StatusThe mandatory state of the FAN 4 being instrumented.ro RlEnvMonState (RADLAN-HWENVIROMENT) .1.3.6.1.4.1.89.53.15.1.7 |
rlPhdUnitEnvParamFan5StatusThe mandatory state of the FAN 5 being instrumented.ro RlEnvMonState (RADLAN-HWENVIROMENT) .1.3.6.1.4.1.89.53.15.1.8 |
rlPhdUnitEnvParamTempSensorValueCurrent value for the Sensor being instrumented.ro EntitySensorValue (ENTITY-SENSOR-MIB) .1.3.6.1.4.1.89.53.15.1.9 |
rlPhdUnitEnvParamTempSensorStatusStatus value for the Sensor being instrumented.ro EntitySensorStatus (ENTITY-SENSOR-MIB) .1.3.6.1.4.1.89.53.15.1.10 |
rlPhdUnitEnvParamUpTimeUp time of the unit in 100th of second (sec/100).ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.89.53.15.1.11 |
rlPhdStackOrderTopUnitThis scalar mib holds the Top unit for the stack order commandrw INTEGER .1.3.6.1.4.1.89.53.16 |
rlPhdStackOrderBottomUnitThis scalar mib holds the Bottom unit for the stack order commandrw INTEGER .1.3.6.1.4.1.89.53.17 |
rlPhdStackOrderPermutationThis scalar mib holds stack permutationrw OCTET STRING .1.3.6.1.4.1.89.53.18 |
rlPhdNumberOfPoeUnitsShows the current number of poe units in the stack.ro INTEGER .1.3.6.1.4.1.89.53.19 |
rlPhdPoeTableFor each module (board) there is an entry describing it in this
module SEQUENCE OF RlPhdPoeEntry .1.3.6.1.4.1.89.53.20 |
rlPhdPoeEntryA entry of this table specifies a module (board) RlPhdPoeEntry .1.3.6.1.4.1.89.53.20.1 |
rlPhdPoeStackUnitThe stack unit to which this module belongs.ro INTEGER .1.3.6.1.4.1.89.53.20.1.1 |
rlPhdPoePresentThe present state of the PoE module. The no(1) state indicates
that the PoE module is not present. The yes{2) state indicates that the
PoE module is present.ro Enumeration .1.3.6.1.4.1.89.53.20.1.2 |
rlPhdPhyLedStackUnitThis scalar mib holds the unit number for the stack light commandrw INTEGER .1.3.6.1.4.1.89.53.21 |
rlPhdPhyLedTimeoutThis scalar mib holds the timeout for the stack light command.
May be in the range 2..60 sec. (default - 5 sec.), if the timeout = 0
- all units return to normal state.rw INTEGER .1.3.6.1.4.1.89.53.22 |
rlCascadeTableFor each cascaded port for stacking unit there is an entry describing it in this table SEQUENCE OF RlCascadeEntry .1.3.6.1.4.1.89.53.23 |
rlCascadeEntryA entry of this table specifies a cascaded port information in a unit RlCascadeEntry .1.3.6.1.4.1.89.53.23.1 |
rlCascadeNeighborIfIndexThe ifIndex of a stacking port in the neighbor unit -
0 means not connected; other integer indicates the IfIndex.ro InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.89.53.23.1.1 |
rlCascadeNeighborUnitThe unit number of the neighbor unit -
0 means not connected; other integer indicates the unit number.ro INTEGER .1.3.6.1.4.1.89.53.23.1.2 |
rlCascadeTrunkIdThe id of the trunk, the stacking port is member,
zero if the port is not member of trunk.ro INTEGER .1.3.6.1.4.1.89.53.23.1.3 |
rlCascadeAfterResetTableFor each cascaded port for stacking unit there is an entry describing it in this table after reset SEQUENCE OF RlCascadeAfterResetEntry .1.3.6.1.4.1.89.53.24 |
rlCascadeAfterResetEntryA entry of this table specifies a cascaded port information in a unit after reset RlCascadeAfterResetEntry .1.3.6.1.4.1.89.53.24.1 |
rlCascadeIfIndexAfterResetThe ifIndex of a stacking port after reset.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.89.53.24.1.1 |
rlCascadeTrunkIdAfterResetThe Id of the trunk, the stacking port will be member after reset,
zero if the port is not member of trunk.rw INTEGER .1.3.6.1.4.1.89.53.24.1.2 |
rlCascadeRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.53.24.1.3 |