MAU-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for MAU-MIB.
118
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
118 total| Object Name |
|---|
snmpDot3MauMgt OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26 |
snmpDot3MauTraps OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.0 |
rpMauJabberTrapThis trap is sent whenever a managed repeater
MAU enters the jabber state.
The agent MUST throttle the generation of
consecutive rpMauJabberTraps so that there is at
least a five-second gap between them. TRAP-TYPE .1.3.6.1.4.1.727.7.2.1.26.0.1 |
ifMauJabberTrapThis trap is sent whenever a managed interface
MAU enters the jabber state.
The agent MUST throttle the generation of
consecutive ifMauJabberTraps so that there is at
least a five-second gap between them. TRAP-TYPE .1.3.6.1.4.1.727.7.2.1.26.0.2 |
dot3RpMauBasicGroup OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.1 |
rpMauTableTable of descriptive and status information
about the MAU(s) attached to the ports of a
repeater. SEQUENCE OF RpMauEntry .1.3.6.1.4.1.727.7.2.1.26.1.1 |
rpMauEntryAn entry in the table, containing information
about a single MAU. RpMauEntry .1.3.6.1.4.1.727.7.2.1.26.1.1.1 |
rpMauGroupIndexThis variable uniquely identifies the group
containing the port to which the MAU described
by this entry is connected.
Note: In practice, a group will generally be
a field-replaceable unit (i.e., module, card,
or board) that can fit in the physical system
enclosure, and the group number will correspond
to a number marked on the physical enclosure.
The group denoted by a particular value of this
object is the same as the group denoted by the
same value of rptrGroupIndex.ro INTEGER .1.3.6.1.4.1.727.7.2.1.26.1.1.1.1 |
rpMauPortIndexThis variable uniquely identifies the repeater
port within group rpMauGroupIndex to which the
MAU described by this entry is connected.ro INTEGER .1.3.6.1.4.1.727.7.2.1.26.1.1.1.2 |
rpMauIndexThis variable uniquely identifies the MAU
described by this entry from among other
MAUs connected to the same port
(rpMauPortIndex).ro INTEGER .1.3.6.1.4.1.727.7.2.1.26.1.1.1.3 |
rpMauTypeThis object identifies the MAU type. An
initial set of MAU types are defined above. The
assignment of OBJECT IDENTIFIERs to new types of
MAUs is managed by the IANA. If the MAU type is
unknown, the object identifier
unknownMauType OBJECT IDENTIFIER ::= { 0 0 }
is returned. Note that unknownMauType is a
syntactically valid object identifier, and any
conformant implementation of ASN.1 and the BER
must be able to generate and recognize this
value.ro OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.1.1.1.4 |
rpMauStatusThe current state of the MAU. This object MAY
be implemented as a read-only object by those
agents and MAUs that do not implement software
control of the MAU state. Some agents may not
support setting the value of this object to some
of the enumerated values.
The value other(1) is returned if the MAU is in
a state other than one of the states 2 through
6.
The value unknown(2) is returned when the MAU's
true state is unknown; for example, when it is
being initialized.
A MAU in the operational(3) state is fully
functional, operates, and passes signals to its
attached DTE or repeater port in accordance to
its specification.
A MAU in standby(4) state forces DI and CI to
idle and the media transmitter to idle or fault,
if supported. Standby(4) mode only applies to
link type MAUs. The state of
rpMauMediaAvailable is unaffected.
A MAU in shutdown(5) state assumes the same
condition on DI, CI, and the media transmitter
as though it were powered down or not connected.
The MAU MAY return other(1) value for the
rpMauJabberState and rpMauMediaAvailable objects
when it is in this state. For an AUI, this
state will remove power from the AUI.
Setting this variable to the value reset(6)
resets the MAU in the same manner as a
power-off, power-on cycle of at least one-half
second would. The agent is not required to
return the value reset (6).
Setting this variable to the value
operational(3), standby(4), or shutdown(5)
causes the MAU to assume the respective state
except that setting a mixing-type MAU or an AUI
to standby(4) will cause the MAU to enter the
shutdown state.rw Enumeration .1.3.6.1.4.1.727.7.2.1.26.1.1.1.5 |
rpMauMediaAvailableIf the MAU is a link or fiber type (FOIRL,
10BASE-T, 10BASE-F) then this is equivalent to
the link test fail state/low light function.
For an AUI or a coax (including broadband) MAU
this indicates whether or not loopback is
detected on the DI circuit. The value of this
attribute persists between packets for MAU types
AUI, 10BASE5, 10BASE2, 10BROAD36, and 10BASE-FP.
The value other(1) is returned if the
mediaAvailable state is not one of 2 through 11.
The value unknown(2) is returned when the MAU's
true state is unknown; for example, when it is
being initialized. At power-up or following a
reset, the value of this attribute will be
unknown for AUI, coax, and 10BASE-FP MAUs. For
these MAUs loopback will be tested on each
transmission during which no collision is
detected. If DI is receiving input when DO
returns to IDL after a transmission and there
has been no collision during the transmission
then loopback will be detected. The value of
this attribute will only change during
non-collided transmissions for AUI, coax, and
10BASE-FP MAUs.
For 100Mbps and 1000Mbps MAUs, the enumerations
match the states within the respective link
integrity state diagrams, fig 32-16, 23-12 and
24-15 of sections 32, 23 and 24 of [16]. Any
MAU which implements management of
auto-negotiation will map remote fault
indication to remote fault.
The value available(3) indicates that the link,
light, or loopback is normal. The value
notAvailable(4) indicates link loss, low light,
or no loopback.
The value remoteFault(5) indicates that a fault
has been detected at the remote end of the link.
This value applies to 10BASE-FB, 100BASE-T4 Far
End Fault Indication and non-specified remote
faults from a system running auto-negotiation.
The values remoteJabber(7), remoteLinkLoss(8),
and remoteTest(9) SHOULD be used instead of
remoteFault(5) where the reason for remote fault
is identified in the remote signaling protocol.
The value invalidSignal(6) indicates that an
invalid signal has been received from the other
end of the link. InvalidSignal(6) applies only
to MAUs of type 10BASE-FB.
Where an IEEE Std 802.3u-1995 clause 22 MII
is present, a logic one in the remote fault bit
(reference section 22.2.4.2.8 of that document)
maps to the value remoteFault(5), and a logic
zero in the link status bit (reference section
22.2.4.2.10 of that document) maps to the value
notAvailable(4). The value notAvailable(4)
takes precedence over the value remoteFault(5).
Any MAU that implements management of clause 37
Auto-Negotiation will map the received Remote
Fault (RF1 and RF2) bit values for Offline to
offline(10), Link Failure to remoteFault(5) and
Auto-Negotiation Error to autoNegError(11).ro Enumeration .1.3.6.1.4.1.727.7.2.1.26.1.1.1.6 |
rpMauMediaAvailableStateExitsA count of the number of times that
rpMauMediaAvailable for this MAU instance leaves
the state available(3).
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by the
value of rptrMonitorPortLastChange.ro Counter .1.3.6.1.4.1.727.7.2.1.26.1.1.1.7 |
rpMauJabberStateThe value other(1) is returned if the jabber
state is not 2, 3, or 4. The agent MUST always
return other(1) for MAU type dot3MauTypeAUI.
The value unknown(2) is returned when the MAU's
true state is unknown; for example, when it is
being initialized.
If the MAU is not jabbering the agent returns
noJabber(3). This is the 'normal' state.
If the MAU is in jabber state the agent returns
the jabbering(4) value.ro Enumeration .1.3.6.1.4.1.727.7.2.1.26.1.1.1.8 |
rpMauJabberingStateEntersA count of the number of times that
mauJabberState for this MAU instance enters the
state jabbering(4). For MAUs of type
dot3MauTypeAUI, dot3MauType100BaseT4,
dot3MauType100BaseTX, dot3MauType100BaseFX and
all 1000Mbps types, this counter will always
indicate zero.
Discontinuities in the value of this counter
can occur at re-initialization of the
management system, and at other times as
indicated by the value of
rptrMonitorPortLastChange.ro Counter .1.3.6.1.4.1.727.7.2.1.26.1.1.1.9 |
rpMauFalseCarriersA count of the number of false carrier events
during IDLE in 100BASE-X links. This counter
does not increment at the symbol rate. It can
increment after a valid carrier completion at a
maximum rate of once per 100 ms until the next
carrier event.
This counter increments only for MAUs of type
dot3MauType100BaseT4, dot3MauType100BaseTX, and
dot3MauType100BaseFX and all 1000Mbps types.
For all other MAU types, this counter will
always indicate zero.
The approximate minimum time for rollover of
this counter is 7.4 hours.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by the
value of rptrMonitorPortLastChange.ro Counter .1.3.6.1.4.1.727.7.2.1.26.1.1.1.10 |
rpJackTableInformation about the external jacks attached
to MAUs attached to the ports of a repeater. SEQUENCE OF RpJackEntry .1.3.6.1.4.1.727.7.2.1.26.1.2 |
rpJackEntryAn entry in the table, containing information
about a particular jack. RpJackEntry .1.3.6.1.4.1.727.7.2.1.26.1.2.1 |
rpJackIndexThis variable uniquely identifies the jack
described by this entry from among other jacks
attached to the same MAU (rpMauIndex). INTEGER .1.3.6.1.4.1.727.7.2.1.26.1.2.1.1 |
rpJackTypeThe jack connector type, as it appears on the
outside of the system.ro JackType -- Rsyntax INTEGER { -- other(1), -- rj45(2), -- rj45S(3), -- db9(4), -- bnc(5), -- fAUI(6), -- mAUI(7), -- fiberSC(8), -- fiberMIC(9), -- fiberST(10), -- telco(11), -- mtrj(12), -- hssdc(13) -- } .1.3.6.1.4.1.727.7.2.1.26.1.2.1.2 |
dot3IfMauBasicGroup OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.2 |
ifMauTableTable of descriptive and status information
about MAU(s) attached to an interface. SEQUENCE OF IfMauEntry .1.3.6.1.4.1.727.7.2.1.26.2.1 |
ifMauEntryAn entry in the table, containing information
about a single MAU. IfMauEntry .1.3.6.1.4.1.727.7.2.1.26.2.1.1 |
ifMauIfIndexThis variable uniquely identifies the interface
to which the MAU described by this entry is
connected.ro INTEGER .1.3.6.1.4.1.727.7.2.1.26.2.1.1.1 |
ifMauIndexThis variable uniquely identifies the MAU
described by this entry from among other MAUs
connected to the same interface (ifMauIfIndex).ro INTEGER .1.3.6.1.4.1.727.7.2.1.26.2.1.1.2 |
ifMauTypeThis object identifies the MAU type. An
initial set of MAU types are defined above. The
assignment of OBJECT IDENTIFIERs to new types of
MAUs is managed by the IANA. If the MAU type is
unknown, the object identifier
unknownMauType OBJECT IDENTIFIER ::= { 0 0 }
is returned. Note that unknownMauType is a
syntactically valid object identifier, and any
conformant implementation of ASN.1 and the BER
must be able to generate and recognize this
value.
This object represents the operational type of
the MAU, as determined by either (1) the result
of the auto-negotiation function or (2) if
auto-negotiation is not enabled or is not
implemented for this MAU, by the value of the
object ifMauDefaultType. In case (2), a set to
the object ifMauDefaultType will force the MAU
into the new operating mode.ro OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.2.1.1.3 |
ifMauStatusThe current state of the MAU. This object MAY
be implemented as a read-only object by those
agents and MAUs that do not implement software
control of the MAU state. Some agents may not
support setting the value of this object to some
of the enumerated values.
The value other(1) is returned if the MAU is in
a state other than one of the states 2 through
6.
The value unknown(2) is returned when the MAU's
true state is unknown; for example, when it is
being initialized.
A MAU in the operational(3) state is fully
functional, operates, and passes signals to its
attached DTE or repeater port in accordance to
its specification.
A MAU in standby(4) state forces DI and CI to
idle and the media transmitter to idle or fault,
if supported. Standby(4) mode only applies to
link type MAUs. The state of
ifMauMediaAvailable is unaffected.
A MAU in shutdown(5) state assumes the same
condition on DI, CI, and the media transmitter
as though it were powered down or not connected.
The MAU MAY return other(1) value for the
ifMauJabberState and ifMauMediaAvailable objects
when it is in this state. For an AUI, this
state will remove power from the AUI.
Setting this variable to the value reset(6)
resets the MAU in the same manner as a
power-off, power-on cycle of at least one-half
second would. The agent is not required to
return the value reset (6).
Setting this variable to the value
operational(3), standby(4), or shutdown(5)
causes the MAU to assume the respective state
except that setting a mixing-type MAU or an AUI
to standby(4) will cause the MAU to enter the
shutdown state.rw Enumeration .1.3.6.1.4.1.727.7.2.1.26.2.1.1.4 |
ifMauMediaAvailableIf the MAU is a link or fiber type (FOIRL,
10BASE-T, 10BASE-F) then this is equivalent to
the link test fail state/low light function.
For an AUI or a coax (including broadband) MAU
this indicates whether or not loopback is
detected on the DI circuit. The value of this
attribute persists between packets for MAU types
AUI, 10BASE5, 10BASE2, 10BROAD36, and 10BASE-FP.
The value other(1) is returned if the
mediaAvailable state is not one of 2 through 11.
The value unknown(2) is returned when the MAU's
true state is unknown; for example, when it is
being initialized. At power-up or following a
reset, the value of this attribute will be
unknown for AUI, coax, and 10BASE-FP MAUs. For
these MAUs loopback will be tested on each
transmission during which no collision is
detected. If DI is receiving input when DO
returns to IDL after a transmission and there
has been no collision during the transmission
then loopback will be detected. The value of
this attribute will only change during
non-collided transmissions for AUI, coax, and
10BASE-FP MAUs.
For 100Mbps and 1000Mbps MAUs, the enumerations
match the states within the respective link
integrity state diagrams, fig 32-16, 23-12 and
24-15 of sections 32, 23 and 24 of [16]. Any
MAU which implements management of
auto-negotiation will map remote fault
indication to remote fault.
The value available(3) indicates that the link,
light, or loopback is normal. The value
notAvailable(4) indicates link loss, low light,
or no loopback.
The value remoteFault(5) indicates that a fault
has been detected at the remote end of the link.
This value applies to 10BASE-FB, 100BASE-T4 Far
End Fault Indication and non-specified remote
faults from a system running auto-negotiation.
The values remoteJabber(7), remoteLinkLoss(8),
and remoteTest(9) SHOULD be used instead of
remoteFault(5) where the reason for remote fault
is identified in the remote signaling protocol.
The value invalidSignal(6) indicates that an
invalid signal has been received from the other
end of the link. InvalidSignal(6) applies only
to MAUs of type 10BASE-FB.
Where an IEEE Std 802.3u-1995 clause 22 MII
is present, a logic one in the remote fault bit
(reference section 22.2.4.2.8 of that document)
maps to the value remoteFault(5), and a logic
zero in the link status bit (reference section
22.2.4.2.10 of that document) maps to the value
notAvailable(4). The value notAvailable(4)
takes precedence over the value remoteFault(5).
Any MAU that implements management of clause 37
Auto-Negotiation will map the received RF1 and
RF2 bit values for Offline to offline(10), Link
Failure to remoteFault(5) and Auto-Negotiation
Error to autoNegError(11).ro Enumeration .1.3.6.1.4.1.727.7.2.1.26.2.1.1.5 |
ifMauMediaAvailableStateExitsA count of the number of times that
ifMauMediaAvailable for this MAU instance leaves
the state available(3).
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by the
value of ifCounterDiscontinuityTime.ro Counter .1.3.6.1.4.1.727.7.2.1.26.2.1.1.6 |
ifMauJabberStateThe value other(1) is returned if the jabber
state is not 2, 3, or 4. The agent MUST always
return other(1) for MAU type dot3MauTypeAUI.
The value unknown(2) is returned when the MAU's
true state is unknown; for example, when it is
being initialized.
If the MAU is not jabbering the agent returns
noJabber(3). This is the 'normal' state.
If the MAU is in jabber state the agent returns
the jabbering(4) value.ro Enumeration .1.3.6.1.4.1.727.7.2.1.26.2.1.1.7 |
ifMauJabberingStateEntersA count of the number of times that
mauJabberState for this MAU instance enters the
state jabbering(4). This counter will always
indicate zero for MAUs of type dot1MauTypeAUI
and those of speeds above 10Mbps.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by the
value of ifCounterDiscontinuityTime.ro Counter .1.3.6.1.4.1.727.7.2.1.26.2.1.1.8 |
ifMauFalseCarriersA count of the number of false carrier events
during IDLE in 100BASE-X and 1000BASE-X links.
For all other MAU types, this counter will
always indicate zero. This counter does not
increment at the symbol rate.
It can increment after a valid carrier
completion at a maximum rate of once per 100 ms
for 100BASE-X and once per 10us for 1000BASE-X
until the next CarrierEvent.
Discontinuities in the value of this counter can
occur at re-initialization of the management
system, and at other times as indicated by the
value of ifCounterDiscontinuityTime.ro Counter .1.3.6.1.4.1.727.7.2.1.26.2.1.1.9 |
ifMauTypeList********* THIS OBJECT IS DEPRECATED **********
A value that uniquely identifies the set of
possible IEEE 802.3 types that the MAU could be.
The value is a sum which initially takes the
value zero. Then, for each type capability of
this MAU, 2 raised to the power noted below is
added to the sum. For example, a MAU which has
the capability to be only 10BASE-T would have a
value of 512 (2**9). In contrast, a MAU which
supports both 10Base-T (full duplex) and
100BASE-TX (full duplex) would have a value of
((2**11) + (2**16)) or 67584.
The powers of 2 assigned to the capabilities are
these:
Power Capability
0 other or unknown
1 AUI
2 10BASE-5
3 FOIRL
4 10BASE-2
5 10BASE-T duplex mode unknown
6 10BASE-FP
7 10BASE-FB
8 10BASE-FL duplex mode unknown
9 10BROAD36
10 10BASE-T half duplex mode
11 10BASE-T full duplex mode
12 10BASE-FL half duplex mode
13 10BASE-FL full duplex mode
14 100BASE-T4
15 100BASE-TX half duplex mode
16 100BASE-TX full duplex mode
17 100BASE-FX half duplex mode
18 100BASE-FX full duplex mode
19 100BASE-T2 half duplex mode
20 100BASE-T2 full duplex mode
If auto-negotiation is present on this MAU, this
object will map to ifMauAutoNegCapability.
This object has been deprecated in favour of
ifMauTypeListBits.rodeprecated INTEGER .1.3.6.1.4.1.727.7.2.1.26.2.1.1.10 |
ifMauDefaultTypeThis object identifies the default
administrative baseband MAU type, to be used in
conjunction with the operational MAU type
denoted by ifMauType.
The set of possible values for this object is
the same as the set defined for the ifMauType
object.
This object represents the
administratively-configured type of the MAU. If
auto-negotiation is not enabled or is not
implemented for this MAU, the value of this
object determines the operational type of the
MAU. In this case, a set to this object will
force the MAU into the specified operating mode.
If auto-negotiation is implemented and enabled
for this MAU, the operational type of the MAU
is determined by auto-negotiation, and the value
of this object denotes the type to which the MAU
will automatically revert if/when
auto-negotiation is later disabled.
NOTE TO IMPLEMENTORS: It may be necessary to
provide for underlying hardware implementations
which do not follow the exact behavior specified
above. In particular, when
ifMauAutoNegAdminStatus transitions from enabled
to disabled, the agent implementation MUST
ensure that the operational type of the MAU (as
reported by ifMauType) correctly transitions to
the value specified by this object, rather than
continuing to operate at the value earlier
determined by the auto-negotiation function.rw OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.2.1.1.11 |
ifMauAutoNegSupportedThis object indicates whether or not
auto-negotiation is supported on this MAU.ro TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.727.7.2.1.26.2.1.1.12 |
ifMauTypeListBitsA value that uniquely identifies the set of
possible IEEE 802.3 types that the MAU could be.
If auto-negotiation is present on this MAU, this
object will map to ifMauAutoNegCapability.
Note that this MAU may be capable of operating
as a MAU type that is beyond the scope of this
MIB. This is indicated by returning the
bit value bOther in addition to any bit values
for capabilities that are listed above.ro OCTET STRING .1.3.6.1.4.1.727.7.2.1.26.2.1.1.13 |
ifJackTableInformation about the external jacks attached
to MAUs attached to an interface. SEQUENCE OF IfJackEntry .1.3.6.1.4.1.727.7.2.1.26.2.2 |
ifJackEntryAn entry in the table, containing information
about a particular jack. IfJackEntry .1.3.6.1.4.1.727.7.2.1.26.2.2.1 |
ifJackIndexThis variable uniquely identifies the jack
described by this entry from among other jacks
attached to the same MAU. INTEGER .1.3.6.1.4.1.727.7.2.1.26.2.2.1.1 |
ifJackTypeThe jack connector type, as it appears on the
outside of the system.ro JackType -- Rsyntax INTEGER { -- other(1), -- rj45(2), -- rj45S(3), -- db9(4), -- bnc(5), -- fAUI(6), -- mAUI(7), -- fiberSC(8), -- fiberMIC(9), -- fiberST(10), -- telco(11), -- mtrj(12), -- hssdc(13) -- } .1.3.6.1.4.1.727.7.2.1.26.2.2.1.2 |
dot3BroadMauBasicGroup OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.3 |
broadMauBasicTable********* THIS OBJECT IS DEPRECATED **********
Table of descriptive and status information
about the broadband MAUs connected to
interfaces.deprecated SEQUENCE OF BroadMauBasicEntry .1.3.6.1.4.1.727.7.2.1.26.3.1 |
broadMauBasicEntry********* THIS OBJECT IS DEPRECATED **********
An entry in the table, containing information
about a single broadband MAU.deprecated BroadMauBasicEntry .1.3.6.1.4.1.727.7.2.1.26.3.1.1 |
broadMauIfIndex********* THIS OBJECT IS DEPRECATED **********
This variable uniquely identifies the interface
to which the MAU described by this entry is
connected.rodeprecated INTEGER .1.3.6.1.4.1.727.7.2.1.26.3.1.1.1 |
broadMauIndex********* THIS OBJECT IS DEPRECATED **********
This variable uniquely identifies the MAU
connected to interface broadMauIfIndex that is
described by this entry.rodeprecated INTEGER .1.3.6.1.4.1.727.7.2.1.26.3.1.1.2 |
broadMauXmtRcvSplitType********* THIS OBJECT IS DEPRECATED **********
This object indicates the type of frequency
multiplexing/cabling system used to separate the
transmit and receive paths for the 10BROAD36
MAU.
The value other(1) is returned if the split type
is not either single or dual.
The value single(2) indicates a single cable
system. The value dual(3) indicates a dual
cable system, offset normally zero.rodeprecated Enumeration .1.3.6.1.4.1.727.7.2.1.26.3.1.1.3 |
broadMauXmtCarrierFreq********* THIS OBJECT IS DEPRECATED **********
This variable indicates the transmit carrier
frequency of the 10BROAD36 MAU in MHz/4; that
is, in units of 250 kHz.rodeprecated INTEGER .1.3.6.1.4.1.727.7.2.1.26.3.1.1.4 |
broadMauTranslationFreq********* THIS OBJECT IS DEPRECATED **********
This variable indicates the translation offset
frequency of the 10BROAD36 MAU in MHz/4; that
is, in units of 250 kHz.rodeprecated INTEGER .1.3.6.1.4.1.727.7.2.1.26.3.1.1.5 |
dot3MauType OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4 |
dot3MauTypeAUI OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.1 |
dot3MauType10Base5 OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.2 |
dot3MauTypeFoirl OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.3 |
dot3MauType10Base2 OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.4 |
dot3MauType10BaseT OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.5 |
dot3MauType10BaseFP OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.6 |
dot3MauType10BaseFB OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.7 |
dot3MauType10BaseFL OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.8 |
dot3MauType10Broad36 OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.9 |
dot3MauType10BaseTHD OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.10 |
dot3MauType10BaseTFD OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.11 |
dot3MauType10BaseFLHD OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.12 |
dot3MauType10BaseFLFD OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.13 |
dot3MauType100BaseT4 OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.14 |
dot3MauType100BaseTXHD OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.15 |
dot3MauType100BaseTXFD OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.16 |
dot3MauType100BaseFXHD OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.17 |
dot3MauType100BaseFXFD OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.18 |
dot3MauType100BaseT2HD OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.19 |
dot3MauType100BaseT2FD OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.20 |
dot3MauType1000BaseXHD OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.21 |
dot3MauType1000BaseXFD OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.22 |
dot3MauType1000BaseLXHD OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.23 |
dot3MauType1000BaseLXFD OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.24 |
dot3MauType1000BaseSXHD OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.25 |
dot3MauType1000BaseSXFD OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.26 |
dot3MauType1000BaseCXHD OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.27 |
dot3MauType1000BaseCXFD OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.28 |
dot3MauType1000BaseTHD OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.29 |
dot3MauType1000BaseTFD OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.4.30 |
dot3IfMauAutoNegGroup OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.5 |
ifMauAutoNegTableConfiguration and status objects for the
auto-negotiation function of MAUs attached to
interfaces. SEQUENCE OF IfMauAutoNegEntry .1.3.6.1.4.1.727.7.2.1.26.5.1 |
ifMauAutoNegEntryAn entry in the table, containing configuration
and status information for the auto-negotiation
function of a particular MAU. IfMauAutoNegEntry .1.3.6.1.4.1.727.7.2.1.26.5.1.1 |
ifMauAutoNegAdminStatusSetting this object to enabled(1) will cause
the interface which has the auto-negotiation
signaling ability to be enabled.
If the value of this object is disabled(2) then
the interface will act as it would if it had no
auto-negotiation signaling. Under these
conditions, an IEEE 802.3 MAU will immediately
be forced to the state indicated by the value of
the object ifMauDefaultType.
NOTE TO IMPLEMENTORS: When
ifMauAutoNegAdminStatus transitions from enabled
to disabled, the agent implementation MUST
ensure that the operational type of the MAU (as
reported by ifMauType) correctly transitions to
the value specified by the ifMauDefaultType
object, rather than continuing to operate at the
value earlier determined by the auto-negotiation
function.rw Enumeration .1.3.6.1.4.1.727.7.2.1.26.5.1.1.1 |
ifMauAutoNegRemoteSignalingA value indicating whether the remote end of
the link is using auto-negotiation signaling. It
takes the value detected(1) if and only if,
during the previous link negotiation, FLP Bursts
were received.ro Enumeration .1.3.6.1.4.1.727.7.2.1.26.5.1.1.2 |
ifMauAutoNegConfigA value indicating the current status of the
auto-negotiation process. The enumeration
parallelDetectFail(5) maps to a failure in
parallel detection as defined in 28.2.3.1 of
[IEEE 802.3 Std].ro Enumeration .1.3.6.1.4.1.727.7.2.1.26.5.1.1.4 |
ifMauAutoNegCapability********* THIS OBJECT IS DEPRECATED **********
A value that uniquely identifies the set of
capabilities of the local auto-negotiation
entity. The value is a sum which initially
takes the value zero. Then, for each capability
of this interface, 2 raised to the power noted
below is added to the sum. For example, an
interface which has the capability to support
only 100Base-TX half duplex would have a value
of 32768 (2**15). In contrast, an interface
which supports both 100Base-TX half duplex and
and 100Base-TX full duplex would have a value of
98304 ((2**15) + (2**16)).
The powers of 2 assigned to the capabilities are
these:
Power Capability
0 other or unknown
(1-9) (reserved)
10 10BASE-T half duplex mode
11 10BASE-T full duplex mode
12 (reserved)
13 (reserved)
14 100BASE-T4
15 100BASE-TX half duplex mode
16 100BASE-TX full duplex mode
17 (reserved)
18 (reserved)
19 100BASE-T2 half duplex mode
20 100BASE-T2 full duplex mode
Note that interfaces that support this MIB may
have capabilities that extend beyond the scope
of this MIB.
This object has been deprecated in favour of
ifMauAutoNegCapabilityBitsrodeprecated INTEGER .1.3.6.1.4.1.727.7.2.1.26.5.1.1.5 |
ifMauAutoNegCapAdvertised********* THIS OBJECT IS DEPRECATED **********
A value that uniquely identifies the set of
capabilities advertised by the local
auto-negotiation entity. Refer to
ifMauAutoNegCapability for a description of the
possible values of this object.
Capabilities in this object that are not
available in ifMauAutoNegCapability cannot be
enabled.
This object has been deprecated in favour of
ifMauAutoNegCapAdvertisedBitsrwdeprecated INTEGER .1.3.6.1.4.1.727.7.2.1.26.5.1.1.6 |
ifMauAutoNegCapReceived********* THIS OBJECT IS DEPRECATED **********
A value that uniquely identifies the set of
capabilities received from the remote
auto-negotiation entity. Refer to
ifMauAutoNegCapability for a description of the
possible values of this object.
Note that interfaces that support this MIB may
be attached to remote auto-negotiation entities
which have capabilities beyond the scope of this
MIB.
This object has been deprecated in favour of
ifMauAutoNegCapReceivedBitsrodeprecated INTEGER .1.3.6.1.4.1.727.7.2.1.26.5.1.1.7 |
ifMauAutoNegRestartIf the value of this object is set to
restart(1) then this will force auto-negotiation
to begin link renegotiation. If auto-negotiation
signaling is disabled, a write to this object
has no effect.
Setting the value of this object to norestart(2)
has no effect.rw Enumeration .1.3.6.1.4.1.727.7.2.1.26.5.1.1.8 |
ifMauAutoNegCapabilityBitsA value that uniquely identifies the set of
capabilities of the local auto-negotiation
entity. Note that interfaces that support this
MIB may have capabilities that extend beyond the
scope of this MIB.
Note that the local auto-negotiation entity may
support some capabilities beyond the scope of
this MIB. This is indicated by returning the
bit value bOther in addition to any bit values
for capabilities that are listed above.ro OCTET STRING .1.3.6.1.4.1.727.7.2.1.26.5.1.1.9 |
ifMauAutoNegCapAdvertisedBitsA value that uniquely identifies the set of
capabilities advertised by the local
auto-negotiation entity.
Capabilities in this object that are not
available in ifMauAutoNegCapabilityBits cannot
be enabled.
Note that the local auto-negotiation entity may
advertise some capabilities beyond the scope of
this MIB. This is indicated by returning the
bit value bOther in addition to any bit values
for capabilities that are listed above.rw OCTET STRING .1.3.6.1.4.1.727.7.2.1.26.5.1.1.10 |
ifMauAutoNegCapReceivedBitsA value that uniquely identifies the set of
capabilities received from the remote
auto-negotiation entity.
Note that interfaces that support this MIB may
be attached to remote auto-negotiation entities
which have capabilities beyond the scope of this
MIB. This is indicated by returning the bit
value bOther in addition to any bit values for
capabilities that are listed above.ro OCTET STRING .1.3.6.1.4.1.727.7.2.1.26.5.1.1.11 |
ifMauAutoNegRemoteFaultAdvertisedA value that identifies any local fault
indications that this MAU has detected and will
advertise at the next auto-negotiation
interaction for 1000Mbps MAUs.rw Enumeration .1.3.6.1.4.1.727.7.2.1.26.5.1.1.12 |
ifMauAutoNegRemoteFaultReceivedA value that identifies any fault indications
received from the far end of a link by the
local auto-negotiation entity for 1000Mbps
MAUs.ro Enumeration .1.3.6.1.4.1.727.7.2.1.26.5.1.1.13 |
mauMod OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.6 |
RFC1155-SMI Unknown .1.3.6.1.4.1.727.7.2.1.26.6 |
mauModConf OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.6.1 |
mauModCompls OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.6.1.1 |
mauModRpCompl OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.6.1.1.1 |
mauModIfCompl OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.6.1.1.2 |
mauModIfCompl2 OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.6.1.1.3 |
mauModRpCompl2 OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.6.1.1.4 |
mauModObjGrps OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.6.1.2 |
mauRpGrpBasic OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.6.1.2.1 |
mauRpGrp100Mbs OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.6.1.2.2 |
mauRpGrpJack OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.6.1.2.3 |
mauIfGrpBasic OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.6.1.2.4 |
mauIfGrp100Mbs OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.6.1.2.5 |
mauIfGrpJack OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.6.1.2.6 |
mauIfGrpAutoNeg OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.6.1.2.7 |
mauBroadBasic OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.6.1.2.8 |
mauIfGrpHighCapacity OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.6.1.2.9 |
mauIfGrpAutoNeg2 OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.6.1.2.10 |
mauIfGrpAutoNeg1000Mbps OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.6.1.2.11 |
mauModNotGrps OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.6.1.3 |
rpMauNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.6.1.3.1 |
ifMauNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.727.7.2.1.26.6.1.3.2 |