RAD-DS1-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for RAD-DS1-MIB.
90
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
90 total| Object Name |
|---|
ds1Interface OBJECT IDENTIFIER .1.3.6.1.4.1.164.3.1.6.4 |
RAD-MIB NOTIFICATION-TYPE .1.3.6.1.4.1.164.3.1.6.4 |
prtDS1Events OBJECT IDENTIFIER .1.3.6.1.4.1.164.3.1.6.4.0 |
ds1LocalMultiframeAlarmTrapThis trap indicates near end (Local) Loss of
Multiframe Alignment, of the user E1 interface. NOTIFICATION-TYPE .1.3.6.1.4.1.164.3.1.6.4.0.1 |
ds1RemoteMultiframeAlarmTrapThis trap indicates that the far end (remote) unit,
connected to the user E1 interface, reports
Loss of Multiframe Alignment. NOTIFICATION-TYPE .1.3.6.1.4.1.164.3.1.6.4.0.2 |
ds1LinkFrameSlipTrapThis trap indicates that a Frame Slip occurred at the user
DS1 interface. This usually indicates timing problems
(incorrect selection of timing reference),
on the user DS1 link. NOTIFICATION-TYPE .1.3.6.1.4.1.164.3.1.6.4.0.3 |
ds1BpvErrorTrapThis trap indicates a Bipolar Violation (BPV)
error has been detected at the user DS1 interface. NOTIFICATION-TYPE .1.3.6.1.4.1.164.3.1.6.4.0.4 |
ds1ExcessiveBpvTrapThis trap indicates excessive number of
Bipolar Violation errors (BPV)
detected by the user DS1 interface NOTIFICATION-TYPE .1.3.6.1.4.1.164.3.1.6.4.0.5 |
ds1Crc4ErrorTrapThis trap indicates that a frame with CRC-4 error has been
detected at the user DS1 interface. NOTIFICATION-TYPE .1.3.6.1.4.1.164.3.1.6.4.0.6 |
ds1ExcessiveErrorRatioTrapThis trap indicates that the error rate, detected
at the user DS1 interface, on the frame synchronization bits
is high, as defined by ITU-T Rec. G.732. NOTIFICATION-TYPE .1.3.6.1.4.1.164.3.1.6.4.0.7 |
ds1RemoteSyncLossTrapThis trap indicates that the far-end (remote)
unit, connected to user DS1 interface,
reports Loss of Frame Alignment (Sync Loss). NOTIFICATION-TYPE .1.3.6.1.4.1.164.3.1.6.4.0.8 |
ds1LocalSyncLossTrapThis trap indicates near end (Local)
Loss of Frame Alignment failure (Sync Loss),
of the user DS1 interface NOTIFICATION-TYPE .1.3.6.1.4.1.164.3.1.6.4.0.9 |
ds1AisSyncLossTrapThis trap indicates near end (Local)
Loss of Frame Alignment (Sync Loss), caused by the reception
of AIS at the user DS1 interface. NOTIFICATION-TYPE .1.3.6.1.4.1.164.3.1.6.4.0.10 |
ds1AisTrapThis trap indicates AIS being received
at the user DS1 interface. NOTIFICATION-TYPE .1.3.6.1.4.1.164.3.1.6.4.0.11 |
ds1NetworkRemoteLoopTrapThis trap indicates that a remote loopback
has been activated, on the local uplink interface. NOTIFICATION-TYPE .1.3.6.1.4.1.164.3.1.6.4.0.12 |
ds1RemoteLoopTrapThis trap indicates that a remote loopback
has been activated, on the local user port. NOTIFICATION-TYPE .1.3.6.1.4.1.164.3.1.6.4.0.13 |
ds1LocalLoopTrapThis trap indicates that a local loopback
has been activated on the user port. NOTIFICATION-TYPE .1.3.6.1.4.1.164.3.1.6.4.0.14 |
ds1ExcessiveFrameSlipTrapThis trap indicates that the number of Frame Slips
detected at the user DS1 interface, during the last minute
exceeds threshold. For LA-110, threshold value is 10.
This usually indicates timing problems
(incorrect selection of timing reference) on the user DS1. NOTIFICATION-TYPE .1.3.6.1.4.1.164.3.1.6.4.0.15 |
ds1ExcessiveCrc4ErrorTrapThis trap indicates that the error rate
detected on the CRC-4 bits at the
user DS1 interface, is high. NOTIFICATION-TYPE .1.3.6.1.4.1.164.3.1.6.4.0.16 |
ds1ExcessiveLocalMfAlarmTrapThis trap indicates that the number of local
Loss of Multiframe Alignment events, detected at
the user E1 interface during the last minute exceeds threshold.
For LA-110, threshold value is 10. NOTIFICATION-TYPE .1.3.6.1.4.1.164.3.1.6.4.0.17 |
ds1ExcessiveRemoteMfAlarmTrapThis trap indicates that the number of
Loss of multiframe alignment events reported
by the remote unit connected to the user
E1 interface during the last minute exceeds threshold.
For LA-110, threshold value is 10. NOTIFICATION-TYPE .1.3.6.1.4.1.164.3.1.6.4.0.18 |
ds1ExcessiveRemoteSyncLossTrapThis trap indicates that the number of far end
(remote) Loss of Synchronization alarms,
reported by the user DS1 interface
during the last minute, exceeds threshold.
For LA-110, threshold value is 10. NOTIFICATION-TYPE .1.3.6.1.4.1.164.3.1.6.4.0.19 |
ds1ExcessiveLocalSyncLossTrapThis trap indicates that the number of
Loss of local Synchronization alarms
reported by the user DS1 interface
during the last minute, exceeds threshold.
For LA-110, threshold value is 10. NOTIFICATION-TYPE .1.3.6.1.4.1.164.3.1.6.4.0.20 |
prtDs1PerfHistory OBJECT IDENTIFIER .1.3.6.1.4.1.164.3.1.6.4.1 |
dsx1XCurrentTableA list of current statistics entries. This table
contains additional objects for the current table. SEQUENCE OF Dsx1XCurrentEntry .1.3.6.1.4.1.164.3.1.6.4.1.2 |
dsx1XCurrentEntryAn entry containing additional statistical counters
applicable to a particular current table. Dsx1XCurrentEntry .1.3.6.1.4.1.164.3.1.6.4.1.2.1 |
dsx1CurrentLOSThe counter associated with the number of LOS
seconds, encountered by a DS1 interface in
the current 15 minute interval.ro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.164.3.1.6.4.1.2.1.1 |
dsx1CurrentLOFThe counter associated with the number of LOF
seconds, encountered by a DS1
interface in the current 15 minute interval.ro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.164.3.1.6.4.1.2.1.2 |
dsx1CurrentLOCLoss Of Cell delineation. Counts number of cells the ATM UNI cells receiver
lost cells delineation .ro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.164.3.1.6.4.1.2.1.3 |
dsx1CurrentAISThe counter associated with the number of AIS
seconds, encountered by a DS1
interface in the current 15 minute interval.ro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.164.3.1.6.4.1.2.1.4 |
dsx1CurrentRAIRemote Alarm Indication: Transmitted in the outgoing direction
(toward the PABX) over FDL bits when the DS1 device detected
an incoming Loss Of Frame. Received from the far end (PABX)
over FDL when it detects a Loss of frame.ro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.164.3.1.6.4.1.2.1.5 |
dsx1CurrentLOMFLoss of Multi-Frame sequence in E1 time slot 16.ro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.164.3.1.6.4.1.2.1.6 |
dsx1CurrentFEBEFar End Block Errors, as reported in the first bit
of frames 13 and 15, on multiframe E1 lines with CRC4,
in the current 15 minute interval.ro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.164.3.1.6.4.1.2.1.7 |
dsx1CurrentStatusThe statuses of the current interval:
0 - Valid.
1 - redundantLinkSwitch - the link has been switched
by a redundancy mechanism.
2 - discontinuity - module was partialy out.
4 - notValid - module is out.ro OCTET STRING .1.3.6.1.4.1.164.3.1.6.4.1.2.1.8 |
dsx1CurrentBPVThe counter associated with the number of BPVs (Bi-Polar Violations)
encountered by a DS1 interface in the current 15 minute interval.ro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.164.3.1.6.4.1.2.1.9 |
dsx1CurrentLOCRCMFLoss of CRC4 Multi-Frame sequence in E1.
encountered in the current 15 minute intervalro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.164.3.1.6.4.1.2.1.10 |
dsx1CurrentLOFCCounts the number of loss of frame events measured.
encountered in the current 15 minute intervalro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.164.3.1.6.4.1.2.1.11 |
dsx1CurrentCRCErrorsCounts the number of CRC error events,
encountered in the current 15 minute interval.ro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.164.3.1.6.4.1.2.1.12 |
dsx1XIntervalTableA list of Interval entries. This table
contains additional objects for the interval table. SEQUENCE OF Dsx1XIntervalEntry .1.3.6.1.4.1.164.3.1.6.4.1.3 |
dsx1XIntervalEntryAn entry containing additional statistical counters
applicable to a particular interval table. Dsx1XIntervalEntry .1.3.6.1.4.1.164.3.1.6.4.1.3.1 |
dsx1IntervalLOSThe counter associated with the number of LOS
seconds , encountered by a DS1 interface in
one of the previous 96, individual 15 minute,
intervals.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.164.3.1.6.4.1.3.1.1 |
dsx1IntervalLOFThe counter associated with the number of OOF
seconds, encountered by a DS1
interface in one of the previous 96, individual 15
minute, intervals.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.164.3.1.6.4.1.3.1.2 |
dsx1IntervalLOCLoss Of Cell delineation. Counts number of cells the ATM UNI cells receiver
lost cells delineation .ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.164.3.1.6.4.1.3.1.3 |
dsx1IntervalAISThe counter associated with the number of AIS
seconds, encountered by a SONET
interface in one of the previous 96, individual 15
minute, intervals.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.164.3.1.6.4.1.3.1.4 |
dsx1IntervalRAIRemote Alarm Indication: Transmitted in the outgoing direction
(toward the PABX) over FDL bits when the DS1 device detected
an incoming Loss Of Frame. Received from the far end (PABX)
over FDL when it detects a Loss of frame.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.164.3.1.6.4.1.3.1.5 |
dsx1IntervalLOMFLoss of Multi-Frame sequence in E1 time slot 16.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.164.3.1.6.4.1.3.1.6 |
dsx1IntervalFEBEFar End Block Errors, as reported in the first bit
of frames 13 and 15, on multiframe E1 lines with CRC4,
in one of the previous 96, individual, 15 minute intervals.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.164.3.1.6.4.1.3.1.7 |
dsx1IntervalStatusThe statuses of the current interval:
0 - Valid.
1 - redundantLinkSwitch - the link has been switched
by a redundancy mechanism.
2 - discontinuity - module was partialy out.
4 - notValid - module is out.ro OCTET STRING .1.3.6.1.4.1.164.3.1.6.4.1.3.1.8 |
dsx1IntervalBPVThe counter associated with the number of BPV (Bi-Polar Violations)
encountered by a DS1 interface in one of the previous 96,
individual 15 minute, intervals.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.164.3.1.6.4.1.3.1.9 |
dsx1IntervalLOCRCMFLoss of CRC4 Multi-Frame sequence in E1.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.164.3.1.6.4.1.3.1.10 |
dsx1IntervalLOFCCounts the number of loss of frame events measured
in one of the previous 96, individual 15 minute, intervals.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.164.3.1.6.4.1.3.1.11 |
dsx1XTotalTableA list of Total statistics entries. This table
contains additional objects for the Total table. SEQUENCE OF Dsx1XTotalEntry .1.3.6.1.4.1.164.3.1.6.4.1.4 |
dsx1XTotalEntryAn entry containing additional statistical counters
applicable to a particular current table. Dsx1XTotalEntry .1.3.6.1.4.1.164.3.1.6.4.1.4.1 |
dsx1TotalLOSThe counter associated with the number of LOS (Loss of Signal)
seconds encountered by a DS1 interface in the previous
24 hour interval.
Invalid 15 minute intervals count as 0.ro PerfTotalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.164.3.1.6.4.1.4.1.1 |
dsx1TotalBPVThe counter associated with the number of BPV (Bi-Polar Violations)
encountered by a DS1 interface in the previous 24 hour interval.
Invalid 15 minute intervals count as 0.ro PerfTotalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.164.3.1.6.4.1.4.1.9 |
dsx1TotalLOFCThe counter associated with the number loss of frames
encountered by a DS1 interface in the previous 24 hour interval.
Invalid 15 minute intervals count as 0.ro PerfTotalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.164.3.1.6.4.1.4.1.11 |
dsx1DataStreamStatTableThe DS1 Data Stream Statistics table. SEQUENCE OF Dsx1DataStreamStatEntry .1.3.6.1.4.1.164.3.1.6.4.1.5 |
dsx1DataStreamStatEntryAn entry in the DS1 Data Stream Statistics table. Dsx1DataStreamStatEntry .1.3.6.1.4.1.164.3.1.6.4.1.5.1 |
dsx1DataStreamStatIfIndexThe index of the DS1 interface.
It may be ifIndex. Integer32 .1.3.6.1.4.1.164.3.1.6.4.1.5.1.1 |
dsx1DataStreamStatIndexThe DS1 Data Stream Index.
For Vmux - the following indices are used:
1 for Transparent
2-3 for SS71-SS72 (respectively)
4-7 for Data1-Data4 (respectively)
. Integer32 .1.3.6.1.4.1.164.3.1.6.4.1.5.1.2 |
dsx1DataStreamStatValidIndicates whether this Data Stream is valid or not.
When invalid - all counters are irrelevant.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.164.3.1.6.4.1.5.1.3 |
dsx1DataStreamStatInFramesThe counter associated with the number of received frames,
encountered by the DS1 Data Stream.ro Counter32 .1.3.6.1.4.1.164.3.1.6.4.1.5.1.4 |
dsx1DataStreamStatInBytesThe counter associated with the number of received bytes,
encountered by the DS1 Data Stream.ro Counter32 .1.3.6.1.4.1.164.3.1.6.4.1.5.1.5 |
dsx1DataStreamStatInDiscardsThe counter associated with the number of Discarded incoming frames,
encountered by the DS1 Data Stream.ro Counter32 .1.3.6.1.4.1.164.3.1.6.4.1.5.1.6 |
dsx1DataStreamStatInErrorsThe counter associated with the number of received Errored frames,
encountered by the DS1 Data Stream.ro Counter32 .1.3.6.1.4.1.164.3.1.6.4.1.5.1.7 |
dsx1DataStreamStatOutFramesThe counter associated with the number of transmitted frames,
encountered by the DS1 Data Stream.ro Counter32 .1.3.6.1.4.1.164.3.1.6.4.1.5.1.8 |
dsx1DataStreamStatOutBytesThe counter associated with the number of transmitted bytes,
encountered by the DS1 Data Stream.ro Counter32 .1.3.6.1.4.1.164.3.1.6.4.1.5.1.9 |
dsx1DataStreamStatOutDiscardsThe counter associated with the number of Discarded outgoing frames,
encountered by the DS1 Data Stream.ro Counter32 .1.3.6.1.4.1.164.3.1.6.4.1.5.1.10 |
dsx1XConfigTableAn extension to the DS1 Configuration table. SEQUENCE OF Dsx1XConfigEntry .1.3.6.1.4.1.164.3.1.6.4.2 |
dsx1XConfigEntryAn entry containing additional configuration
parameters. Dsx1XConfigEntry .1.3.6.1.4.1.164.3.1.6.4.2.1 |
dsx1IdleCodeByte pattern of the data received/transmitted in the
E1T1 framer idle timeslots.
Valid range: (0 - FF HEX).rw Integer32 .1.3.6.1.4.1.164.3.1.6.4.2.1.1 |
dsx1LineModeT1 device operation mode.
Valid for T1 only.rw Enumeration .1.3.6.1.4.1.164.3.1.6.4.2.1.2 |
dsx1dBTxGainTransmit line Gain for T1 CSU line mode.rw Enumeration .1.3.6.1.4.1.164.3.1.6.4.2.1.3 |
dsx1RxSensitivityDetermine the maximum attenuation of the
receive signal that can be compensated for
by the interface receive path. Not applicable for T1.rw Enumeration .1.3.6.1.4.1.164.3.1.6.4.2.1.4 |
dsx1RestoreTimeUsed to change the sync. algorithms to reduce the time
required for the port to return to normal operation after
a RED alarm.
'sec1' = Fast,
'sec10' = TR-6211,
'immediate' = CCITTrw Enumeration .1.3.6.1.4.1.164.3.1.6.4.2.1.5 |
dsx1TcFirstSignalTrunk conditioning signal - value to be sent as a signal
during the first 2.5 seconds after alarm detection.
Range is 0x0..0xF. 0xFF is a NULL value.
This variable is used also for Space Signaling Code (in this case
0xFF is not NULL).rw Integer32 .1.3.6.1.4.1.164.3.1.6.4.2.1.6 |
dsx1TcSignalTrunk conditioning signal value after alarm detection.
Range is 0x1..0xF for E1, and 0x0..0xF for T1.
This variable is used also for Space Signaling Code (E1 and T1).rw Integer32 .1.3.6.1.4.1.164.3.1.6.4.2.1.7 |
dsx1TcPatternTrunk conditioning data pattern to be sent upon a DS0 fail.
Range is 0x0..0xFF.
This variable used also for Out of Service Code.rw Integer32 .1.3.6.1.4.1.164.3.1.6.4.2.1.8 |
dsx1ScrambleScrambling is an operation that randomizes the bits
of the payload of the ATM cell by a polynom.
This operation helps with the error detection mechanism
of the HEC. Not applicable for E1.
active - will scramble/descramble the payload ATM cell
notActive - will not scramble/descramble.rw Enumeration .1.3.6.1.4.1.164.3.1.6.4.2.1.9 |
dsx1LineAdaptiveTimingModeEnables end to end clock synchronization.
Default value - off.rw Enumeration .1.3.6.1.4.1.164.3.1.6.4.2.1.10 |
dsx1TxClockSourceThe source of Transmit Clock.
'loopTiming' indicates that the recovered receive clock
is used as the transmit clock.
'localTiming' indicates that a local clock
source is used or when an external clock is
attached to the box containing the interface.
'throughTiming' indicates that recovered receive clock
from another interface is used as the transmit clock.
'adaptive' indicates that the clock is recovered according
to the received data flow rate.rw Enumeration .1.3.6.1.4.1.164.3.1.6.4.2.1.11 |
dsx1AisEnableEnable/ disable AIS transmit when Ethernet cable (for TDMoIP) is out (disconnected).rw Enumeration .1.3.6.1.4.1.164.3.1.6.4.2.1.12 |
dsx1TsEchoCancelThis parameter defines for each TS whether Echo-Cancellation is on.
Each bit represents one TS as follow:
First octet bit'0' = TS#1, bit'7' = TS#8, .. 2nd octet bit'0' = TS#9,..,
4th octet bit'7' = TS#32.
Octets and bits order is from left to right:
[31,30,..24] [23..16] [15..8] [7..0]
MSB LSB MSB LSB MSB LSB MSB LSB
For each bit values are:
0 - Echo-Cancellation off.
1 - Echo-Cancellation on.rw OCTET STRING .1.3.6.1.4.1.164.3.1.6.4.2.1.13 |
dsx1EchoCancelerModuleThis parameter indicates whether echo-cancellation module
exists for this line.ro Enumeration .1.3.6.1.4.1.164.3.1.6.4.2.1.14 |
dsx1PortFunctionThis object determines the ATM Mode over the
physical port.
uni - The port will function as an ATM UNI.
ces - The port will function as a CES.
ima - The port will function as an IMA-ATM.rw Enumeration .1.3.6.1.4.1.164.3.1.6.4.2.1.15 |
dsx1PortMultiplierThis object determines the data rate of each TS
(Kbps units).
This parameter is applicable for T1 only.rw Enumeration .1.3.6.1.4.1.164.3.1.6.4.2.1.16 |
dsx1LeasedLineThis parameter defines whether Line mode is regular (non Leased Line mode)
or transparent (Leased Line mode).rw Enumeration .1.3.6.1.4.1.164.3.1.6.4.2.1.17 |
dsx1CsuLoopThis parameter defines whether CSU loop will be done locally (by IPmux)
or will be transferred to the TDM device.rw Enumeration .1.3.6.1.4.1.164.3.1.6.4.2.1.18 |
dsx1ClockSourceThis entry specifies the source from which the clock will be taken.
Refer to device specification for source Indexrw Integer32 .1.3.6.1.4.1.164.3.1.6.4.2.1.19 |
dsx1OosSignalThis parameter defines the value to be sent as a signal
after alarm detection:
'Space' = both A and B signaling bits are forced
to '0' during out-of-service periods.
'Mark' = both A and B signaling bits are forced
to '1' during out-of-service periods.
'spaceMark' = A and B bits are forced to '0' for
2.5 seconds; then they are switched to '1'
until out-of-service condition disappears.
'markSpace' = A and B bits are forced to '1' for
2.5 seconds; then they are switched to '0'
until out-of-service condition disappears.
- '0'= 0 for T1, 1 for E1, or user defined value for Space
- '1'= 1 for T1, 0 for E1, or user defined value for Mark.rw Enumeration .1.3.6.1.4.1.164.3.1.6.4.2.1.20 |