RAD-HDLC-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for RAD-HDLC-MIB.
170
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
170 total| Object Name |
|---|
hdlcMibObjects OBJECT IDENTIFIER .1.3.6.1.4.1.164.3.1.6.5 |
IMPORTS Unknown .1.3.6.1.4.1.164.3.1.6.5 |
hdlcTableThe HDLC configuration table. SEQUENCE OF HdlcEntry .1.3.6.1.4.1.164.3.1.6.5.1 |
hdlcEntryDefines the contents of each line in the RAD HDLC Table. HdlcEntry .1.3.6.1.4.1.164.3.1.6.5.1.1 |
hdlcProtocolThe HDLC protocol type
V35 - HDLC encapsulated over V35
X21 - HDLC encapsulated over X21
RS530 - HDLC encapsulated over RS530rw Enumeration .1.3.6.1.4.1.164.3.1.6.5.1.1.1 |
hdlcRateResolutionThe baud rate of the internal clock.rw Enumeration .1.3.6.1.4.1.164.3.1.6.5.1.1.2 |
hdlcTxClockSourceThe baud rate of the internal clock.rw Enumeration .1.3.6.1.4.1.164.3.1.6.5.1.1.3 |
hdlcTerminalMode.rw Enumeration .1.3.6.1.4.1.164.3.1.6.5.1.1.4 |
hdlcLoopbackStateinternal - All data coming from the
network port is looped back
external - All data comming from the line is
looped back.rw Enumeration .1.3.6.1.4.1.164.3.1.6.5.1.1.5 |
hdlcTxClockPolaritynormal - The transmitted data is sampled at the middle of bit time
inverse - The transmitted data is sampled at the end of the bit time
(high data rate/long cable).rw Enumeration .1.3.6.1.4.1.164.3.1.6.5.1.1.6 |
hdlcFlowControlEnable/Disable the CTS/RTS flow control signals.rw Enumeration .1.3.6.1.4.1.164.3.1.6.5.1.1.7 |
hdlcLineRateThe rate values for HDLC are n*56/64Kbps, where 1<=n<=32, 64, 128
and the following values: 1544, 3088, 6176.
The rate values for HSSI is nMbps, where 1<=n<=52.rw Integer32 .1.3.6.1.4.1.164.3.1.6.5.1.1.8 |
hdlcRxClockMode.rw Enumeration .1.3.6.1.4.1.164.3.1.6.5.1.1.9 |
hdlcLOFTotal number of seconds the port is in Loss Of Frame state.ro Gauge32 .1.3.6.1.4.1.164.3.1.6.5.1.1.10 |
hdlcRxClockPolaritynormal - The received data is sampled at the middle of bit time
inverse - The received data is sampled at the end of the bit time
(high data rate/long cable).rw Enumeration .1.3.6.1.4.1.164.3.1.6.5.1.1.11 |
hdlcPerformance OBJECT IDENTIFIER .1.3.6.1.4.1.164.3.1.6.5.2 |
hdlcCurrentTableThe HDLC Current table. SEQUENCE OF HdlcCurrentEntry .1.3.6.1.4.1.164.3.1.6.5.2.1 |
hdlcCurrentEntryAn entry in the HDLC Current table. HdlcCurrentEntry .1.3.6.1.4.1.164.3.1.6.5.2.1.1 |
hdlcCurrentIfIndexThe index of the HDLC interface.
It may be ifIndex.ro Integer32 .1.3.6.1.4.1.164.3.1.6.5.2.1.1.1 |
hdlcCurrentStatusThe statuses of the current interval:
0 - Valid.
1 - redundantLinkSwitch - the link has been switched
by a redundancy mechanism.
2 - discontinuity - module was partialy out.
4 - notValid - module is out.ro OCTET STRING .1.3.6.1.4.1.164.3.1.6.5.2.1.1.2 |
hdlcCurrentLOFThe counter associated with the number of seconds the
port is in Loss Of Frame state, encountered
by the HDLC interface in the current 15 minute interval.ro Gauge32 .1.3.6.1.4.1.164.3.1.6.5.2.1.1.3 |
hdlcCurrentInFramesThe counter associated with the number of received frames,
encountered by the HDLC interface in the current 15 minute
interval.ro Gauge32 .1.3.6.1.4.1.164.3.1.6.5.2.1.1.4 |
hdlcCurrentInErrorsThe counter associated with the number of Errored received
frames, encountered by the HDLC interface in the current 15
minute interval.ro Gauge32 .1.3.6.1.4.1.164.3.1.6.5.2.1.1.5 |
hdlcCurrentOutFramesThe counter associated with the number of transmitted frames,
encountered by the HDLC interface in the current 15 minute
interval.ro Gauge32 .1.3.6.1.4.1.164.3.1.6.5.2.1.1.6 |
hdlcCurrentAbortedFramesThe counter associated with the number of frames, in which
at least seven consecutive '1'-s (Abort sequence) were
encountered by the HDLC interface in the current 15 minute
interval.ro Gauge32 .1.3.6.1.4.1.164.3.1.6.5.2.1.1.7 |
hdlcCurrentLengthErrorThe counter associated with the number of received frames
with length error, encountered by the HDLC interface in the
current 15 minute interval.ro Gauge32 .1.3.6.1.4.1.164.3.1.6.5.2.1.1.8 |
hdlcIntervalTableThe HDLC Interval table. SEQUENCE OF HdlcIntervalEntry .1.3.6.1.4.1.164.3.1.6.5.2.2 |
hdlcIntervalEntryAn entry in the HDLC Interval table. HdlcIntervalEntry .1.3.6.1.4.1.164.3.1.6.5.2.2.1 |
hdlcIntervalIfIndexThe index of the HDLC interface.
It may be ifIndex.ro Integer32 .1.3.6.1.4.1.164.3.1.6.5.2.2.1.1 |
hdlcIntervalNumberA number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes interval
(assuming that all 96 intervals exist).ro Integer32 .1.3.6.1.4.1.164.3.1.6.5.2.2.1.2 |
hdlcIntervalStatusThe statuses of the current interval:
0 - Valid.
1 - redundantLinkSwitch - the link has been switched
by a redundancy mechanism.
2 - discontinuity - module was partialy out.
4 - notValid - module is out.ro OCTET STRING .1.3.6.1.4.1.164.3.1.6.5.2.2.1.3 |
hdlcIntervalLOFThe counter associated with the number of seconds the
port is in Loss Of Frame state, encountered by an HDLC
interface in one of the previous 96, individual 15 minute,
intervals.ro Gauge32 .1.3.6.1.4.1.164.3.1.6.5.2.2.1.4 |
hdlcIntervalInFramesThe counter associated with the number of received frames,
encountered by the HDLC interface in one of the previous 96,
individual 15 minute, intervals.ro Gauge32 .1.3.6.1.4.1.164.3.1.6.5.2.2.1.5 |
hdlcIntervalInErrorsThe counter associated with the number of Errored received
frames, encountered by the HDLC interface in one of the
previous 96, individual 15 minute, intervals.ro Gauge32 .1.3.6.1.4.1.164.3.1.6.5.2.2.1.6 |
hdlcIntervalOutFramesThe counter associated with the number of transmitted
frames, encountered by the HDLC interface in one of
the previous 96, individual 15 minute, intervals.ro Gauge32 .1.3.6.1.4.1.164.3.1.6.5.2.2.1.7 |
hdlcIntervalAbortedFramesThe counter associated with the number of frames, in which
at least seven consecutive '1'-s (Abort sequence) were
encountered by the HDLC interface in one of the previous 96,
individual 15 minute, intervals.ro Gauge32 .1.3.6.1.4.1.164.3.1.6.5.2.2.1.8 |
hdlcIntervalLengthErrorThe counter associated with the number of received frames
with length error, encountered by the HDLC interface in
one of the previous 96, individual 15 minute, intervals.ro Gauge32 .1.3.6.1.4.1.164.3.1.6.5.2.2.1.9 |
rtrFACSViolationThe trap is sent for every violation of a FACS filter. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.11.0.1 |
rtrSwDwnLoadTrapThe trap is sent after the tftp download of the software
and before the decompression and reset operations. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.11.0.2 |
rtrInterfaces OBJECT IDENTIFIER .1.3.6.1.4.1.164.11.1 |
rtrConfigIfTableTable of configured interfaces. SEQUENCE OF RtrConfigIfEntry .1.3.6.1.4.1.164.11.1.1 |
rtrConfigIfEntryEach entry defines a configured interface. RtrConfigIfEntry .1.3.6.1.4.1.164.11.1.1.1 |
rtrConfigIfIndexThis variable uniquely identifies the interface.
It is used as a cross reference in other system tablesro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.164.11.1.1.1.1 |
rtrConfigIfTypeThis variable identifies the type of the specific
entry in the rtrDynamicIfConfigTable.
This field is writable only at creation time
(i.e., when value of status is underCreation).rw RtrIfConfigTYPE .1.3.6.1.4.1.164.11.1.1.1.2 |
rtrConfigIfNameThis variable provides a logical name to a specific entry in
rtrConfigIfTable. It is also used in identifying the Driver
interfaces.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.164.11.1.1.1.3 |
rtrConfigIfStatusThe status of the ConfigEntry. The choices are those
defined in SNMPv2-TC. Only: active, createAndWait, and destroy
will be used.
active - The conceptual row is available for use by the managed device.
createAndWait - A new instance of a conceptual row is desired, but
not to have it available for use by the managed device.
destroy - Delete all instances associated with an existing conceptual row.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.164.11.1.1.1.4 |
rtrIfCfgTableRouter Interface Configuration Table. SEQUENCE OF RtrIfCfgEntry .1.3.6.1.4.1.164.11.1.2 |
rtrIfCfgEntryAn entry in the Router Interface Configuration Table. RtrIfCfgEntry .1.3.6.1.4.1.164.11.1.2.1 |
rtrIfCfgIndexThis object indicates the Router Interface Index.
(In some cases it will be equal to the Router Interface ifIndex).rw Integer32 .1.3.6.1.4.1.164.11.1.2.1.1 |
rtrIfCfgIpAddressIP Address of the Router Interface.rw IpAddress .1.3.6.1.4.1.164.11.1.2.1.2 |
rtrIfCfgRowStatusThis object enables the user to
create/delete entries of this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.164.11.1.2.1.3 |
rtrIfCfgIpMaskIP Mask Address Router Interface.rw IpAddress .1.3.6.1.4.1.164.11.1.2.1.4 |
rtrIfCfgIfIndexifIndex of the device interface connected
to this Router Interface.rw Integer32 .1.3.6.1.4.1.164.11.1.2.1.5 |
rtrIfCfgTypeThe Router Interface Type.
atm - ATM router interface
lis - Logical IP Subnet router interface.
ethernet - Ethernet router interface.rw Enumeration .1.3.6.1.4.1.164.11.1.2.1.6 |
rtrIfCfgVlanIdThe VLAN ID assigned to Tagged frames transmitted
from this Router Interface.
The value inserted should be a defined VLAN.rw VlanIndex SYNTAX Integer32 .1.3.6.1.4.1.164.11.1.2.1.7 |
rtrIfCfgMtuThe size of the largest packet which can be sent/received
on the interface, specified in octets. For interfaces that
are used for transmitting network datagrams, this is the
size of the largest network datagram that can be sent on the
interface.rw Integer32 .1.3.6.1.4.1.164.11.1.2.1.8 |
ipSpec OBJECT IDENTIFIER .1.3.6.1.4.1.164.11.2 |
rtrIpAddrTableThis table is parralel to MIB II IpAddrTable, and is used to
add/delete entries to/from that table. In addition it contains
private objects. SEQUENCE OF RtrIpAddrEntry .1.3.6.1.4.1.164.11.2.1 |
rtrIpAddrEntryThe addressing information for one of this
entity's IP addresses. RtrIpAddrEntry .1.3.6.1.4.1.164.11.2.1.1 |
rtrIpAdEntAddrThe IP address to which this entry's addressing
information pertains.ro IpAddress .1.3.6.1.4.1.164.11.2.1.1.1 |
rtrIpAdEntIfIndexThe index value which uniquely identifies the
interface to which this entry is applicable. The
interface identified by a particular value of this
index is the same interface as identified by the
same value of ifIndex.rw Integer32 .1.3.6.1.4.1.164.11.2.1.1.2 |
rtrIpAdEntNetMaskThe subnet mask associated with the IP address of
this entry. The value of the mask is an IP
address with all the network bits set to 1 and all
the hosts bits set to 0.rw IpAddress .1.3.6.1.4.1.164.11.2.1.1.3 |
rtrIpAdEntForwardIpBroadcastThis variable controls forwarding of IP (sub)net-directed
broadcasts destined for an attached sub(net).rw Enumeration .1.3.6.1.4.1.164.11.2.1.1.4 |
rtrIpAdEntBackupAddrrw IpAddress .1.3.6.1.4.1.164.11.2.1.1.5 |
rtrIpAdEntStatusThe Status variable is used to create and destroy a Ip Addresses.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.164.11.2.1.1.6 |
icmpSpec OBJECT IDENTIFIER .1.3.6.1.4.1.164.11.2.2 |
rtrIcmpGenErrMsgEnableThis variable controlls the ability to generate ICMP error messagesrw Enumeration .1.3.6.1.4.1.164.11.2.2.1 |
rtrIcmpRdTableThis table contains ICMP Router Discovery parameters
configurated per IP interface. SEQUENCE OF RtrIcmpRdEntry .1.3.6.1.4.1.164.11.2.2.2 |
rtrIcmpRdEntryThe ICMP parameters configurated for IP interface. RtrIcmpRdEntry .1.3.6.1.4.1.164.11.2.2.2.1 |
rtrIcmpRdIpAddrThe IP address to which this entry's information pertains.ro IpAddress .1.3.6.1.4.1.164.11.2.2.2.1.1 |
rtrIcmpRdIpAdvertAddrThe IP destination address to be used for multicast
Router Advertisements sent from the interface. The
only permissible values are the all-systems multicast
address, 224.0.0.1, or the limited-broadcast address,
255.255.255.255.rw IpAddress .1.3.6.1.4.1.164.11.2.2.2.1.2 |
rtrIcmpRdMaxAdvertIntervalThe maximum time allowed between sending multicast
Router Advertisements from the interface, in seconds.
Must be no less than 4 seconds and no greater than 1800
seconds.rw Integer32 .1.3.6.1.4.1.164.11.2.2.2.1.3 |
rtrIcmpRdMinAdvertIntervalThe minimum time allowed between sending unsolicited
multicast Router Advertisements from the interface, in
seconds. Must be no less than 3 seconds and no greater
than rtrIcmpRdMaxAdvertInterval.
Default: 0.75 * rtrIcmpRdMaxAdvertInterval.rw Integer32 .1.3.6.1.4.1.164.11.2.2.2.1.4 |
rtrIcmpRdAdvertLifetimeThe maximum length of time that the advertised addresses
are to be considered as valid. Must be no less than
rtrIcmpRdMaxAdvertInterval and no greater than 9000 seconds.
Default: 3 * rtrIcmpRdMaxAdvertInterval.rw Integer32 .1.3.6.1.4.1.164.11.2.2.2.1.5 |
rtrIcmpRdAdvertiseA flag indicating whether or not the address is to be
advertised.rw Enumeration .1.3.6.1.4.1.164.11.2.2.2.1.6 |
rtrIcmpRdPreferenceLevelThe preferability of the address as a default router
address, relative to other router addresses on the same
subnet.rw Integer32 .1.3.6.1.4.1.164.11.2.2.2.1.7 |
rtrIcmpRdEntStatusSetting of any value to this object set values of
all fields to the default values.rw Integer32 .1.3.6.1.4.1.164.11.2.2.2.1.8 |
rip2Spec OBJECT IDENTIFIER .1.3.6.1.4.1.164.11.2.3 |
rtrRip2IfConfTableThis table is an extension of rip2IfConfTable (RFC 1724 ,RIP 2).
It means that every time somebody creates/destroys a row in the
rip2IfConfTable, the same row should be automatically created/destroyed
in this table. SEQUENCE OF RtrRip2IfConfEntry .1.3.6.1.4.1.164.11.2.3.1 |
rtrRip2IfConfEntryAn entry in table rtrRip2IfConfTable. RtrRip2IfConfEntry .1.3.6.1.4.1.164.11.2.3.1.1 |
rtrRip2IfConfAddressThe IP Address of this system on the indicated subnet.
For unnumbered interfaces, the value 0.0.0.N,
where the least significant 24 bits (N) is the ifIndex
for the IP Interface in network byte orderro IpAddress .1.3.6.1.4.1.164.11.2.3.1.1.1 |
rtrRip2IfConfVirtualDisThis variable defines the virtual number of hops assigned to
the interface specified by rtrIfIpAddrIndex. This enables
fine-tuning of the RIP routing algorithm.rwdeprecated Integer32 .1.3.6.1.4.1.164.11.2.3.1.1.2 |
rtrRip2IfConfAutoSendWhen set to enable only the default route is sent through
the interface. When set to disable, regular RIPs are sent.rwdeprecated Enumeration .1.3.6.1.4.1.164.11.2.3.1.1.3 |
rtrRip2IfConfRipEnableThis object shows whether RIP Protocol is enabled on the current interface.rw Enumeration .1.3.6.1.4.1.164.11.2.3.1.1.4 |
arpSpec OBJECT IDENTIFIER .1.3.6.1.4.1.164.11.2.4 |
rtrArpDeleteTableSetting this object to any not-null value has the effect of deleting
all entries of the ARP table.rw Integer32 .1.3.6.1.4.1.164.11.2.4.1 |
rtrArpInactiveTimeOutThis variable defines the maximum time period (in second) that can
pass between ARP requests concerning an entry in the ARP table.
After this time period, the entry is deleted from the table.rw Integer32 .1.3.6.1.4.1.164.11.2.4.2 |
rtrArpProxyWhen ARP Proxy is enabled, the router can respond to
ARP requests for nodes located on a different sub-net,
provided they are it its network table. The router responds
with its own MAC address.
When ARP Proxy is disabled, the router responds only
to ARP requests for its own IP addresses.rw Enumeration .1.3.6.1.4.1.164.11.2.4.3 |
rtrNat OBJECT IDENTIFIER .1.3.6.1.4.1.164.11.2.5 |
rtrNatIfConfTableA list of interfaces which require separate NAT configuration. SEQUENCE OF RtrNatIfConfEntry .1.3.6.1.4.1.164.11.2.5.1 |
rtrNatIfConfEntryA single routing domain in a single subnet. RtrNatIfConfEntry .1.3.6.1.4.1.164.11.2.5.1.1 |
rtrNatIfVirtualAddressThe IP Address of the virtual subnet to be translated by the 'NAT box'
attached to this interface.ro IpAddress .1.3.6.1.4.1.164.11.2.5.1.1.1 |
rtrNatIfVirtualMaskThe subnet Mask of the virtual subnet.ro IpAddress .1.3.6.1.4.1.164.11.2.5.1.1.2 |
rtrNatIfConfStatusWriting 'destroy' has the effect of deleting this interface.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.164.11.2.5.1.1.3 |
rtrNatIfRealAddressThe IP Address of the real subnet which is used by 'NAT box' for translation.rw IpAddress .1.3.6.1.4.1.164.11.2.5.1.1.4 |
rtrNatIfRealMaskThe subnet Mask of the real subnet.rw IpAddress .1.3.6.1.4.1.164.11.2.5.1.1.5 |
rtrNatIfTypeNAT type.
static - Translate a specific virtual IP network to a specific real IP
network. TCP, UDP and ICMP sessions originated both in real and
virtual networks will be translated.
dynamic - (Concurrent) Translate real IP network to larger or equal virtual
IP network. TCP, UDP and ICMP sessions originated in virtual
networks only can be translated and sessions originated in real
networks will be rejected. A session that starts in the NAT system
will be active until there will be no traffic for aging timeout
period.
pat - (Port Address Translation/ Single IP).
Translate one real IP address to virtual IP network. TCP, UDP and
ICMP sessions originated in virtual network only can be translated,
sessions originated in real network will be rejected. A session
that starts in the NAT system will be active until there will be no
traffic for aging timeout period.
transparent - In transparent mode all frames belonging to the defined IP
network will be forwarded with no translation: virtual = real.rw Enumeration .1.3.6.1.4.1.164.11.2.5.1.1.6 |
rtrPatTablePort Address Translation (PAT - single IP NAT) configuration Table. SEQUENCE OF RtrPatEntry .1.3.6.1.4.1.164.11.2.5.2 |
rtrPatEntryEach entry describe unique mapping between real IP address,
range of ports and protocol, to local (virtual) IP address.
Ports are used in the TCP (rfc793) to name the ends of logical
connections which carry long term conversations.
For the purpose of providing services to unknown callers,
a service contact port is defined. RtrPatEntry .1.3.6.1.4.1.164.11.2.5.2.1 |
rtrPatIdxRunning index for PAT table.ro Integer32 .1.3.6.1.4.1.164.11.2.5.2.1.1 |
rtrPatRealAddressThe real IP Address used for translationrw IpAddress .1.3.6.1.4.1.164.11.2.5.2.1.2 |
rtrPatVirtualAddressThe virtual IP Address used for translationrw IpAddress .1.3.6.1.4.1.164.11.2.5.2.1.3 |
rtrPatLowestPortLowest Port number for this PAT entryrw Integer32 .1.3.6.1.4.1.164.11.2.5.2.1.4 |
rtrPatHighestPortHighest Port number for this PAT entryrw Integer32 .1.3.6.1.4.1.164.11.2.5.2.1.5 |
rtrPatProtocolProtocol selected.
This Protocol and port range (lowest port - highest port)
define the application (FTP, Telnet, SMTP etc.).
Protocol enumaration numbers correspond to
IP header 'protocol' fieldrw Enumeration .1.3.6.1.4.1.164.11.2.5.2.1.6 |
rtrPatStatusThis object enables creating and deleting
entries of the table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.164.11.2.5.2.1.7 |
rtrFACS OBJECT IDENTIFIER .1.3.6.1.4.1.164.11.5 |
rtrFACSDefaultActionUsed to define the default action for the device, when no
FACS statements applicable to a given frame are defined.rw Enumeration .1.3.6.1.4.1.164.11.5.1 |
rtrFACSActTableThe table of FACS action. SEQUENCE OF RtrFACSActEntry .1.3.6.1.4.1.164.11.5.2 |
rtrFACSActEntryEach rtrFACSActEntry consist of the following parameters RtrFACSActEntry .1.3.6.1.4.1.164.11.5.2.1 |
rtrFACSActTypeThis parameter indicates on which FACS Table the FACS
action will preform.ro Enumeration .1.3.6.1.4.1.164.11.5.2.1.1 |
rtrFACSActIfIndexThe interface to which this FACS entry is applicable.ro Integer32 .1.3.6.1.4.1.164.11.5.2.1.2 |
rtrFACSActionThe management station that sends a SET request for one of these actions
with indexes rtrFACSType and rtrFACSIfIndex defines the type and the
interface Id for which all FACS statements are to be erased.
If no interface or no type is specified, all FACS statements for a
protocol are erased.rw Enumeration .1.3.6.1.4.1.164.11.5.2.1.3 |
rtrFACSActiveDBThis parameter will point on which Facs DataBase the SNMP agent
read. The Active dataBase is Read Only. The user may change FACS
statements in the temporary DataBase and then write it to the
Active DB.rw Enumeration .1.3.6.1.4.1.164.11.5.2.1.4 |
rtrFACSTableThe table of FACS statment. SEQUENCE OF RtrFACSEntry .1.3.6.1.4.1.164.11.5.3 |
rtrFACSEntryEach FACS statment consists of the following parameters RtrFACSEntry .1.3.6.1.4.1.164.11.5.3.1 |
rtrFACSIfIndexThe interface to which this FACS entry is applicable.
For applications this variables is always 0.ro Integer32 .1.3.6.1.4.1.164.11.5.3.1.1 |
rtrFACSProtocolTypeThis parameter define the protocol the Security Access Control
is applicable.ro Enumeration .1.3.6.1.4.1.164.11.5.3.1.2 |
rtrFACSTypeThe Mode of in which this FACS statement operates.
For applications this variable is always rx(2).ro Enumeration .1.3.6.1.4.1.164.11.5.3.1.3 |
rtrFACSIndexIndex to the FACS Table.ro Integer32 .1.3.6.1.4.1.164.11.5.3.1.4 |
rtrFACSSrcAddThe size of the octet string will be according to the protocol type
defined in rtrFACSProtocolType.rw OCTET STRING .1.3.6.1.4.1.164.11.5.3.1.5 |
rtrFACSSrcAddMaskSource-address mask .rw OCTET STRING .1.3.6.1.4.1.164.11.5.3.1.6 |
rtrFACSDesAddDestination-address The size of the octet string will be according to the
protocol type define in rtrFACSProtocolType .rw OCTET STRING .1.3.6.1.4.1.164.11.5.3.1.7 |
rtrFACSDesAddMaskDestination-address mask .rw OCTET STRING .1.3.6.1.4.1.164.11.5.3.1.8 |
rtrFACSOperation... .rw Enumeration .1.3.6.1.4.1.164.11.5.3.1.9 |
rtrFACSNetFiltering... .rw Enumeration .1.3.6.1.4.1.164.11.5.3.1.10 |
rtrFACSSocketNumPort/socket number for different applications
0 is default meaning not applicable.
none(1),
ftp(21),
telnet(23),
smtp(25),
tftp(69),
snmp(161),
snmpTrap(162),
rip(520),
sapIPX(1106),
ripIPX(1107)rw Integer32 .1.3.6.1.4.1.164.11.5.3.1.11 |
rtrFACSMask1IdIndex into RND mask table FACS/COD Type) .rw Integer32 .1.3.6.1.4.1.164.11.5.3.1.12 |
rtrFACSMask2IdIndex into RND mask table FACS/COD according to
the value of rtrFACSType .rw Integer32 .1.3.6.1.4.1.164.11.5.3.1.13 |
rtrFACSStatusThe status of a table entry.rw Enumeration .1.3.6.1.4.1.164.11.5.3.1.14 |
rtrFACSFrameDataData from the frame that violated a FACS Filter.ro OCTET STRING .1.3.6.1.4.1.164.11.5.4 |
rtrBridgePortConfigTableTable of the bridge ports SEQUENCE OF RtrBridgePortConfigEntry .1.3.6.1.4.1.164.11.7.1 |
rtrBridgePortConfigEntryEach entry defines a bridge port RtrBridgePortConfigEntry .1.3.6.1.4.1.164.11.7.1.1 |
rtrBridgePortCIndexThis is the index of the bridge port. It is the same
as 'dot1dBasePort' of the Bridge MIB.ro Integer32 .1.3.6.1.4.1.164.11.7.1.1.1 |
rtrBridgePortCIfThe config ifIndex the bridge port is sitting on.rw Integer32 .1.3.6.1.4.1.164.11.7.1.1.2 |
rtrBridgePortCStatusThe status of the RtrBridgePortConfigEntry.
Creating and destroying the bridge port is done by this
variable.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.164.11.7.1.1.3 |
radRouterConfig OBJECT IDENTIFIER .1.3.6.1.4.1.164.11.9 |
rtrConfigTableThe Router's Configuration table. SEQUENCE OF RtrConfigEntry .1.3.6.1.4.1.164.11.9.1 |
rtrConfigEntryAn entry in the Router's Configuration table. RtrConfigEntry .1.3.6.1.4.1.164.11.9.1.1 |
rtrConfigIndexThis object indicates the Router's Index.ro Integer32 .1.3.6.1.4.1.164.11.9.1.1.1 |
rtrConfigDefaultGatewayRouter Default Gateway.rw IpAddress .1.3.6.1.4.1.164.11.9.1.1.2 |
rtrConfigArpAgingTimeARP Aging Time.rw Integer32 .1.3.6.1.4.1.164.11.9.1.1.3 |
rtrConfigClassifierTosMaskThis object indicates the Classifier's TOS Mask,
as follows:
0x1C for DTR
0x1E for Cisco
0xE0 for Precedence
0xFC for Diffserv
Else for Manual
.rw Integer32 .1.3.6.1.4.1.164.11.9.1.1.5 |
rtrConfigRIPModeThis object determines the Router Information Protocol
to measure the shortest path between 2 positions
on the network.rw Enumeration .1.3.6.1.4.1.164.11.9.1.1.6 |
rtrFwdTableThe Router's Forwarding Table. SEQUENCE OF RtrFwdEntry .1.3.6.1.4.1.164.11.9.3 |
rtrFwdEntryAn entry in the Router's Forwarding table. RtrFwdEntry .1.3.6.1.4.1.164.11.9.3.1 |
rtrFwdIdxThis object indicates the Router Index.ro Integer32 .1.3.6.1.4.1.164.11.9.3.1.1 |
rtrFwdIpAddressThis object indicates the Destination IP Address.ro IpAddress .1.3.6.1.4.1.164.11.9.3.1.2 |
rtrFwdIpMaskThis object indicates the Mask IP address.ro IpAddress .1.3.6.1.4.1.164.11.9.3.1.3 |
rtrFwdRuleIdxThis object indicates the Rule's Number.ro Integer32 .1.3.6.1.4.1.164.11.9.3.1.4 |
rtrFwdRowStatusThis object enables the user to
create/delete entries in this table.
Entry of Type rtrFwdType = staticRouting(3)
are created by the user.
Only this type of entries can be deleted by the user.
Entry of Type rtrFwdType = interface(2)
are created/deleted automatically by the Agent
when the user creates/deletes an interface of the Router.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.164.11.9.3.1.5 |
rtrFwdNextHopThis object indicates the IP Address of the Next Hop.rw IpAddress .1.3.6.1.4.1.164.11.9.3.1.6 |
rtrFwdIfIndexThis object indicates the Interface Index.ro Integer32 .1.3.6.1.4.1.164.11.9.3.1.7 |
rtrFwdTypeThe type of route. Note that local(3) refers
to a route for which the next hop is the final
destination; remote(4) refers to a route for
which the next hop is not the final destina-
tion.
Routes which do not result in traffic forwarding or
rejection should not be displayed even if the
implementation keeps them stored internally.
reject (2) refers to a route which, if matched, discards
the message as unreachable. This is used in some
protocols as a means of correctly aggregating routes.rw Enumeration .1.3.6.1.4.1.164.11.9.3.1.8 |
rtrFwdProtoThe routing mechanism via which this route was
learned. Inclusion of values for gateway routing
protocols is not intended to imply that
hosts should support those protocols.ro Enumeration .1.3.6.1.4.1.164.11.9.3.1.9 |
rtrFwdEthQueueThis object indicates the ETH Queue number.rw Integer32 .1.3.6.1.4.1.164.11.9.3.1.10 |
rtrFwdMetric1The primary routing metric for this route.
The semantics of this metric are determined by
the routing-protocol specified in the route's
rtrFwdProto value. If this metric is not
used, its value should be set to -1.rw Integer32 .1.3.6.1.4.1.164.11.9.3.1.11 |
radAtmSignalingMonitor OBJECT IDENTIFIER .radAtm.6 |
smSVCOperStateThe SVC monitoring operational state.ro Enumeration .radAtm.6.1 |
smSVCAdminStatusThe SVC monitoring status.rw Enumeration .radAtm.6.2 |
smILMIModeThe ILMI operational Mode.rw Enumeration .radAtm.6.3 |
smILMIStatusILMI protocol status (VCC 0,16).ro Enumeration .radAtm.6.4 |
smUNIVersionThe UNI version that is used by both sides.rw Enumeration .radAtm.6.5 |
smPolicingThe type of the police action performed on
the cells transmitted from the user side to
the network side.rw Enumeration .radAtm.6.6 |
smSAALStatusSignaling data link (VCC 0,5) status.ro Enumeration .radAtm.6.7 |
smOpenedSesssionsThe number of SVC sessions currently opened.ro Gauge32 .radAtm.6.8 |
smUserRejectedSessionsThe number of sessions that the user side rejected
to open.ro Gauge32 .radAtm.6.9 |
smNetworkRejectedSessionsThe number of sessions that the Network side rejected.ro Gauge32 .radAtm.6.10 |
smHostRejectedSessionsThe number of sessions that the device rejected
to open.ro Gauge32 .radAtm.6.11 |
smVclILMISessionVpiILMI Keep alive session VPI channel.
Default: 0. (VCI=16, fixed).rw Integer32 .radAtm.6.12 |