RAD-ARC-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for RAD-ARC-MIB.
553
Objects
Active
Status
9
Dependencies
Imported Objects
Objects
553 total| Object Name |
|---|
atmNteSys OBJECT IDENTIFIER .1 |
atmAceStatusChangeThe trap is sent every time there is a change in
the state of one of the LEDs. NOTIFICATION-TYPE .1 |
atmNteSysConfig OBJECT IDENTIFIER .1.1 |
atmNteManagerTableThe Manager Table includes all the NMSs that
receive traps from this agent. A single manager
can receive traps on more than one PVC. The PVCs
must be from the four allowed. The agent will set
implicitly the correct ifIndex, VPI, VCI values to
all relevant entries in the table when the user changes
them for one of the PVCs. SEQUENCE OF AtmNteManagerEntry .1.1.1 |
atmNteManagerEntryA single manager and the PVC for receiving traps. AtmNteManagerEntry .1.1.1.1 |
atmNteManagerIPThe IP address of the NMS.ro IpAddress .1.1.1.1.1 |
atmNteManagerPvcA PVC index. The range is 1..8. There are four PVCs
on the User Port and four PVCs on the Network Port.
The default VPI, VCI values are specified below.ro Integer32 .1.1.1.1.2 |
atmNteManagerIfIndexThe ATM interface index of the management port.rw Integer32 .1.1.1.1.3 |
atmNteManagerVpiThe VPI of the management VCL. Default: 0.rw Integer32 .1.1.1.1.4 |
atmNteManagerVciThe VCI of the management VCL. Defaults: 32,33,34,35.rw Integer32 .1.1.1.1.5 |
atmNteManagerTrapMaskThe value of this attribute determines the type of traps the
agent should mask and not send to this NMS. The
value is differently determined for different products. There are
mainly two methods:
- an integer number, specifying the traps' severity.
- a sum of 2**n, where n is a bit assigned to a certain
masked trap group.
User should consult the product specification, to find out
the method employed.rw Integer32 .1.1.1.1.6 |
atmNteManagerRowStatusCreation/Deletion of rows in the table.rw RowStatus (SNMPv2-TC) .1.1.1.1.7 |
atmNteManagerNextHopThis parameter is relevant to Ethernet out of band
host only (PVC=10).
The Next Hop IP address of the entry route.rw IpAddress .1.1.1.1.8 |
atmNteManagerVlanSupportVLAN support (Tagging).
no - No support to VLAN.
yes - 4 VLAN bytes will be added to the frame.rw Enumeration .1.1.1.1.9 |
atmNteManagerVlanIdentifierVLAN ID. Range is 0..4095.rw Integer32 .1.1.1.1.10 |
atmNteManagerVlanFramePriorityVLAN Frame priority.Range is 0..7.rw Integer32 .1.1.1.1.11 |
atmNteManagerAlarmTrapMaskThe value of this object determines the alarm traps that the
agent should mask and not send to this NMS.
The value is an Octet String, where each bit is assigned to a certain
trap.
If the bit = 1, the trap will be masked.
If the bit = 0, the trap will not be masked.
More details on the masked traps exist in the product specification.
For products that do not mask specific traps, the value of the bits will be 0.rw OCTET STRING .1.1.1.1.12 |
atmNteManagerConfigPortsThis variable defines from which port/s this manager can configure the device.
For IPmux 11 the value of this variable will be according to the ports
combination:
Network =1
User1=2
User2=4
(For Example: All ports = 7).rw Integer32 .1.1.1.1.13 |
atmNteUPLTCRThe Unacceptable ES Limit threshold for Performance Management.rw Integer32 .1.1.2 |
atmNteDPLTCRThe Degraded ES Limit threshold for Performance Management.rw Integer32 .1.1.3 |
atmNteSysLogClearAllSetting the variable to clear(3) removes all entries in the
Log Buffer of the agent. The agent will immediately reset
the variable to off(2).rw Enumeration .1.1.4 |
atmNteUSESLTCRThe Unacceptable SES Limit threshold for Performance Management.rw Integer32 .1.1.5 |
atmNteDSESLTCRThe Degraded ES Limit threshold for Performance Management.rw Integer32 .1.1.6 |
atmNteProtection OBJECT IDENTIFIER .1.1.8 |
atmNteProtectionModeProtection Mode.
MspOn - Multiplex section protection.
pathOn - High order path protection.
mspUniOn - Multiplex section Uni-directional protection.
mspOneToN - Multiplex section protection.rw Enumeration .1.1.8.1 |
atmNteProtectionWorkingLinkSelects the working link when atmNteProtectionMode is off.rw Enumeration .1.1.8.2 |
atmNteProtectionSwitchLinkForceSwitch - will force Switching from the working link to the backup link.
Afterwards the agent will set atmNteProtectionSwitchLink back to off(1).
atmNteProtectionMode must be either mspOn or pathOn.rw Enumeration .1.1.8.3 |
atmNteConfOam OBJECT IDENTIFIER .1.1.9 |
atmNteConfOamSupportOAM support mode, which determines the device location
in a segment wise.rw Enumeration .1.1.9.1 |
atmNteConfOamTransmission OBJECT IDENTIFIER .1.1.9.2 |
atmNteConfOamAISDefines if a F4 segment OAM cell is transmitted due
to problems in the other port, i.e. physical layer
alarm or F4 defect. This is valid only when the ACE101
has ATM UNI interfaces in both sides and is configured
for 'Non-Intrusive' mode.
none - AIS is not sent to any of the ports.
user - F4 AIS will be sent toward the user when defect
is detected in the network port.
network - F4 AIS will be sent toward the network when
defect is detected in the user port.
both - F4 AIS will be sent toward the network when defect
is detected in the user port and toward the user
when defect is detected in the network port.rw Enumeration .1.1.9.2.1 |
atmNteConfOamRDIDefines if an F4 OAM RDI cell is transmitted due to
physical layer problems in the port (in addition to
F4 RDI cells transmitted due to ATM layer problems).
The type of F4 RDI (Segment or End-to-End) is according
to the ACE-101 OAM mode.
For example, If it is enabled for Network port, then
physical layer defect will initiate the transmission
of F4 RDI cell back to the trunk.rw Enumeration .1.1.9.2.2 |
atmNteConfOamAddressing OBJECT IDENTIFIER .1.1.9.3 |
atmNteConfLoopbackAddModeLoopback addressing mode.
on - will enable loopback addressing.
off - will disable loopback addressing.rw Enumeration .1.1.9.3.1 |
atmNteConfLoopbackSourceAddLoopback source address. This field is relevant when
atmNteConfOamAddMode is on.rw OCTET STRING .1.1.9.3.2 |
atmNteConfOamIfTableOAM support per ATM interface. SEQUENCE OF AtmNteConfOamIfEntry .1.1.9.4 |
atmNteConfOamIfEntry. AtmNteConfOamIfEntry .1.1.9.4.1 |
atmNteConfOamIfAisRdiThis parameter controls the generation of F4/F5
AIS and RDI due to lower order problems such as physical
layer problems.
For AIS: Defines if F4/F5 AIS cell is transmitted due
to problems such as physical layer alarm or F4/F5 defect.
This is applicable for all ports .
off - Problems in this port will not trigger F4/F5 AIS
transmition to the ajacent port (e.g. from USER to
NETWORK) of a VPC/VCC.
on - Problems in this port will trigger F4/F5 AIS
transmition to the ajacent port (e.g. from USER
to NETWORK) of a VPC/VCC.
For RDI: Defines if F4/F5 RDI cell will be transmitted due to
physical layer problems in that port (in addition to
F4/F5 RDI cells transmitted due to ATM layer problems).
For example, If it is enabled for Network port, then
physical layer defect will initiate the transmission
of F4/F5 RDI cell back to the trunk.
The type of F4/F5 (Segment or End-to-End) is according
to the configuration of the VPC/VCC.rw Enumeration .1.1.9.4.1.1 |
atmNteConfCAC OBJECT IDENTIFIER .1.1.10 |
atmNteConfCACModeCAC support mode.
For ACE2002, the following are the applicable values:
disable(1), enable(2), 10 - 1000.rw Enumeration .1.1.10.1 |
atmNteHostIfTableHost IP interface table. SEQUENCE OF AtmNteHostIfEntry .1.1.11 |
atmNteHostIfEntry. AtmNteHostIfEntry .1.1.11.1 |
atmNteHostPvcIndexA PVC index. The range is 1..8. There are four PVCs
on the User Port and four PVCs on the Network Port.ro Integer32 .1.1.11.1.1 |
atmNteHostIPThe host interface IP address.rw IpAddress .1.1.11.1.2 |
atmNteHostMaskThe host interface subnet mask.rw IpAddress .1.1.11.1.3 |
atmNteHostAtmIfIndexATM interface index. Will be 1
for user port, and 2 for network port.rw Integer32 .1.1.11.1.4 |
atmNteHostVpiVPI of the PVC connected to that host interface.rw Integer32 .1.1.11.1.5 |
atmNteHostVciVCI of the PVC connected to that host interface.rw Integer32 .1.1.11.1.6 |
atmNteHostRowStatusCreation/Deletion of rows in the table.rw RowStatus (SNMPv2-TC) .1.1.11.1.7 |
atmNteHostRdnVpiThe VPI of the redundant management VCL.
This parameter is applicable only if atmNteRdnManagement=enable(3).rw Integer32 .1.1.11.1.8 |
atmNteHostRdnVciThe VCI of the redundant management VCL.
This parameter is applicable only if atmNteRdnManagement=enable(3).rw Integer32 .1.1.11.1.9 |
atmNteHostDefaultNextHopThe host interface Default Next Hop address.
This address will be used as default next hop for
every Bundle mapped to this Host.rw IpAddress .1.1.11.1.10 |
atmNteHostVlanTaggingVLAN Tag support.
no - No support to VLAN.
yes - 4 VLAN bytes will be added
to each frame connected to this Host.rw Enumeration .1.1.11.1.11 |
atmNteHostDefaultVlanIDDefault VLAN ID of this Host.rw Integer32 .1.1.11.1.12 |
atmNteHostDefaultVlanPriorityDefault VLAN priority for this Host.rw Integer32 .1.1.11.1.13 |
atmNteShaperModeShaper Mode.
vpInbandMng - Vcc within a Vp for management.rw Enumeration .1.1.12 |
atmNteOutputRateAggregate shaping output rate in Cells per Seconds units.
Default value is the Network port rate.rw Integer32 .1.1.13 |
atmNteTosModeTOS Mode.rw Enumeration .1.1.14 |
atmNteTosMaskThis parameter determines the seqence of bits that will be used for TOS.
For ACE101 this parameter is applicable only if atmNteTosMode = enable.
Valid only for IP-TOS process.rw OCTET STRING .1.1.15 |
atmNteTosHighPriorityPriorities options are High or Low.
High priority will be represented by bit = 1.
Low priority will be represented by bit = 0.
Each TOS value will be represented by the bit location.
For example, the string for TOS 2, 9, 15 with High priority,
will be:
|0000 0000|... ...|0000 0000|1000 0010|0000 0100|
...98 7654 3210 (Bit #)
8 ... 3 2 1 (Byte #).rw OCTET STRING .1.1.16 |
atmNtePlugAndPlayActivityActivity control for Manager Plug And Play.
disable - disable the feature.
offline - Automatic learn IP address into offline memory.
online - Automatic learn IP address into online memory.rw Enumeration .1.1.17 |
atmNteSlotUsageApplicable to ace2002. Slot 2 might be configured
as user slot or as network slot.rw Enumeration .1.1.18 |
atmNteConnectionsMaxNumberThe MAX number of connections supported by system.
Setting this parameter will affect the number of MAX intervals supported.
This parameter will affect the system only after reset.
Changing this parameter from high value to a low value, will be accepted by agent
only if the actual used connection <= the desired connection Max number.
Applicable to ace2002.rw Enumeration .1.1.19 |
atmNteDefaultVpiDefault Vpi for management.rw Integer32 .1.1.20 |
atmNteDefaultVciDefault Vci for management.rw Integer32 .1.1.21 |
atmNteReservedVpiInternal use VPI, where shaperMode=vpInbandMng.rw Integer32 .1.1.22 |
atmNteRdnManagementThe redundancy management status.ro Enumeration .1.1.23 |
atmNtePlugAndPlayIfIndexThe ifIndex of the Plug and Play VCC.rw InterfaceIndex (IF-MIB) .1.1.24 |
atmNteLoopbackTimeoutThe Loopback state timeout in minutes. A value of
zero means no timeout (for ever). Default is 5 min.rw Integer32 .1.1.25 |
atmNteOamTableThis table is a static table, which is created by agent once
upon initialization. The created entries are actually, only the
supported OAM features.
This table enables addition of new features by adding new entries
rather than adding scalar parameters.
An OAM feature is defined by the indexes values combination. SEQUENCE OF AtmNteOamEntry .1.1.26 |
atmNteOamEntryAn entry in the OAM table.
Each entry in this table will indicate a special OAM. AtmNteOamEntry .1.1.26.1 |
atmNteOamModeThe OAM cell path.
endToEnd(1) - the entire path.ro Enumeration .1.1.26.1.1 |
atmNteOamCellTypeThis object indicates a unique Indication Signal.
aisAndRdi(1) - Alarm Indication Signal (AIS) and
Remote Defect Indication (RDI) cell.
loopback(2) - Loopback cell.ro Enumeration .1.1.26.1.2 |
atmNteOamLevelThe level of the OAM cell.
f5 (3) - VC level.ro Enumeration .1.1.26.1.3 |
atmNteOamEnableThis parameter determines if the specified OAM cells
will be enabled.rw Enumeration .1.1.26.1.4 |
atmNteDefaultLoopbackThresholdThe Default OAM Loopback Failure Threshold value
that will be used for configuration.rw Integer32 .1.1.27 |
atmNteMaxBurstSizeThe Maximum allowed burst size (cell units).
This object is applicable for each Physical port.rw Integer32 .1.1.28 |
atmNteGranularityFactorThis parameter affects the granularity of the guaranteed
Rate (SCR+MCR) in spaced connection (cell/sec units).
It is also defines the minimum guaranteed rate in spaced
connection.rw Integer32 .1.1.29 |
atmNteTotalInputRateThis parameter indicates the total input rate of the
device in cells/sec.ro Integer32 .1.1.30 |
atmNteTotalOutputRateThis parameter indicates the total output rate of the
device in cells/sec.ro Integer32 .1.1.31 |
atmAlarmForwardingTableThe Alarm Forwarding Mechanism will be operated
for this table entries. SEQUENCE OF AtmAlarmForwardingEntry .1.1.32 |
atmAlarmForwardingEntryEach entry in this table is a pair of ports that
the Alarm Forwarding Mechanism is determined for. AtmAlarmForwardingEntry .1.1.32.1 |
atmAlarmForwardingFailPortAn Index of the port on which a fail occurs. Integer32 .1.1.32.1.1 |
atmAlarmForwardingToPortAn Index of the port that will be affected
upon the failure of the atmAlarmForwardingFailPort. Integer32 .1.1.32.1.2 |
atmAlarmForwardingRowStatusCreation/Deletion of rows in the table.rw RowStatus (SNMPv2-TC) .1.1.32.1.3 |
atmAlarmForwardingFailureLevelThis parameter determines the level of failure
that will operate the Alarm Forwarding Mechanism.rw Bits .1.1.32.1.4 |
atmAlarmForwardingRecoveryModeThis parameter determines the Recovery Mode.
manual - The user should stop the RDI transmission
by using the atmAlarmForwardingRecoveryCommand.
automatic - The RDI transmission will be automatically
stopped upon atmAlarmForwardingFailPort
recovery.rw Enumeration .1.1.32.1.5 |
atmAlarmForwardingRecoveryCommandThis parameter is a command. It is applicable when
atmAlarmForwardingRecoveryMode = manual.
on - Will stop the RDI transmission. After setting to 'On'
the agent will set this parameter back to 'Off'.rw Enumeration .1.1.32.1.6 |
atmSysConfigCellTest OBJECT IDENTIFIER .1.1.33 |
atmSysConfigCellTestPortAn Index of the port on which the cell test
will be sent.rw InterfaceIndex (IF-MIB) .1.1.33.1 |
atmSysConfigCellTestVpiThe VPI on which the cell test will be sent.rw Integer32 .1.1.33.2 |
atmSysConfigCellTestVciThe VCI on which the cell test will be sent.rw Integer32 .1.1.33.3 |
atmSysConfigCellTestPtiThe cell type.rw Enumeration .1.1.33.4 |
atmSysConfigCellTestClpThe type of the Cell.rw Enumeration .1.1.33.5 |
atmSysConfigCellTestOamTypeThe OAM type of the Cell. This object is applicable
if atmSysConfigCellTestPti = oamSegment/oamEndToEnd .rw Enumeration .1.1.33.6 |
atmSysConfigCellTestPayloadThe payload of the cell. For OAM cell the payload
is set automatically to 6A.rw OCTET STRING .1.1.33.7 |
atmSysConfigCellTestQuantityQuantity of cells to send.rw Integer32 .1.1.33.8 |
atmSysConfigCellTestSendCmdSetting the variable to send(3) perfroms cell test.
The agent will immediately reset the variable to off(2).rw Enumeration .1.1.33.9 |
atmVpCrossConnectExtenTableAn extension to the ATM VP Cross Connect table
(RFC2515 - atmVpCrossConnectTable). SEQUENCE OF AtmVpCrossConnectExtenEntry .1.1.34 |
atmVpCrossConnectExtenEntryAn entry in the table. AtmVpCrossConnectExtenEntry .1.1.34.1 |
atmVpCrossConnectNameThe Connection's name.rw SnmpAdminString .1.1.34.1.1 |
atmVcCrossConnectExtenTableAn extension to the ATM VC Cross Connect table
(RFC2515 - atmVcCrossConnectTable). SEQUENCE OF AtmVcCrossConnectExtenEntry .1.1.35 |
atmVcCrossConnectExtenEntryAn entry in the table. AtmVcCrossConnectExtenEntry .1.1.35.1 |
atmVcCrossConnectNameThe Connection's name.rw SnmpAdminString .1.1.35.1.1 |
atmNteSysInfo OBJECT IDENTIFIER .1.2 |
atmNteIdTableThe IDs of the cards and of the system. SEQUENCE OF AtmNteIdEntry .1.2.1 |
atmNteIdEntry. AtmNteIdEntry .1.2.1.1 |
atmNteIdIndexAn Index of the Unit ID table.
The following units have IDs in this table:
1 - System
2 - ATM Board
3 - User Card
4 - Trunk 1 card
5 - Trunk 2 card
6 - Shaper
7 - Clock Unit
8 - Slot 1 card
9 - Slot 2 card
10 - Slot 3 card
11 - Slot 4 card
12 - Fan1.
13 - Fan2.ro Integer32 .1.2.1.1.1 |
atmNteUnitIdThe ID of the Unit.
For index = 6, the id will describe the validity
of a shaper in the system: 0 - Shaper Not exist
1 - Shaper exist.
For index = 7, the id will describe the validity
of a clock in the system: 0 - Clock Not exist
1 - Clock exist.
2- Clock exist but failed.
For index = 12,13 the id will describe the functionality
of a FAN1 : 0 - OK
1 - Failed.ro Integer32 .1.2.1.1.2 |
atmNteUnitVersionHardware and Software version
of the module.ro DisplayString (SNMPv2-TC) .1.2.1.1.3 |
atmNteCardTypeThe card type.ro Enumeration .1.2.1.1.4 |
atmNteCardStatusStatus of the card in the selected slot.
notActive - Connections are in NotReady state. No configuration is
available for the card. The access to the card HW is blocked.
This state is relevant for an extracted card, and for a case
in which the card was deactivated.
active - The module installed and functions. A card that in this state
can be configured.
inProgress - The status during proccessing of a command from atmNteCardCmd.
empty - No information is valid for the selected slot. This status is
relevant to a case in which the card configaration was deleted,
or in case in which a slot was empty since the device startup.ro Enumeration .1.2.1.1.5 |
atmNteCardCmdCommand on the card that is installed in the selected slot.
The commands are applicable according to the value of atmNteCardStatus.
See the specification document for details.
deleteConfig - Deletes the card configuration.
deactivate - All the connections state will be changed to NotReady. The card
configuration will be blocked.
activate - Does the same as done upon card insertion: Initiates the relevant
parameters, activates the physical layer, ATM layer and logical
layer.rw Enumeration .1.2.1.1.6 |
atmSysPSunitsThe number of power supply units.ro Integer32 .1.2.2 |
atmSysPSunitsInUseThe main power supply in this unit.ro Enumeration .1.2.3 |
atmSysFanUnitsThe number of fan units.ro Integer32 .1.2.4 |
atmSysNetPrtsThe number of network ports.ro Integer32 .1.2.5 |
atmSysNetPrtInUseThe network port in use.ro Enumeration .1.2.6 |
atmNteBridgingModeBridging mode can be one of the following:
ATM <> Ethernet - Bridging is between the Ethernet
port and the ATM port (there is no bridging between VCs).
ATM <> Ethernet + ATM - Bridging is done both between
the Ethernet port and the ATM port and also between VCs.rw Enumeration .1.2.7 |
atmSysStats OBJECT IDENTIFIER .1.2.8 |
atmSysCurrentCdcSeconds in which cells dropped was occured in
the current 15 minutes interval.ro Gauge32 .1.2.8.1 |
atmSysIntervalTableThe system level Interval table. SEQUENCE OF AtmSysIntervalEntry .1.2.8.2 |
atmSysIntervalEntry. AtmSysIntervalEntry .1.2.8.2.1 |
atmSysIntervalNumberA number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes interval
(assuming that all 96 intervals are valid).ro Integer32 .1.2.8.2.1.1 |
atmSysIntervalCdcSeconds in which cells dropped was occured in
15 minutes interval.ro Gauge32 .1.2.8.2.1.2 |
atmNteEventTypeThis parameter identifies the event.
On - the problem exist.
Off - the problem not exist.
InvalidLogin - Invalid login on local console.
CorrectLogin - Successful login operation.ro Enumeration .1.2.9 |
atmNteIntervalMaxNumberThe MAX number of connections intervals supported by system.
This parameter value is a function of atmNteConnectionsMaxNumber
parameter.
This parameter should affect the threshold values selected by user.
Applicable to ace2002.ro Integer32 .1.2.10 |
atmNteAlarmTypeThis object specifies the type of the alarm.ro Enumeration .1.2.11 |
atmNteLevelThis object specifies the ATM level.ro Enumeration .1.2.12 |
atmNteConnectionsNumberThis object specifies a quantity of connections.ro Integer32 .1.2.13 |
atmNteTotalLbThis parameter counts the total number of end-points
that were configured with Loopback (LB).ro Integer32 .1.2.14 |
atmNteTotalCcThis parameter counts the total number of end-points
that were configured with Continuity Check (CC).ro Integer32 .1.2.15 |
atmNteTotalPmThis parameter counts the total number of end-points
that were configured with PM.ro Integer32 .1.2.16 |
atmAceSystemTrapThis trap alerts of major problems in the device. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.6 |
atmAceAlarmForwardingTrapThis trap is sent upon starting or stopping Alarm
Forwarding Mechanism. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.7 |
atmAceAlarmLOSThis trap indicates Loss Of Signal. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.16 |
atmAceAlarmLOFThis trap indicates Loss Of Frame. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.17 |
atmAceAlarmLCDThis trap indicates Loss of Cell Delineation. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.18 |
atmAceAlarmSLMThis trap indicates Signal Line Mismatch. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.19 |
atmAceAlarmLOPThis trap indicates Loss of Pointer. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.20 |
atmAceAlarmLineAISThis trap indicates Line AIS. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.21 |
atmAceAlarmPathAISThis trap indicates Path AIS. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.22 |
atmAceAlarmLineRDIThis trap indicates Line RDI. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.23 |
atmAceAlarmPathRDIThis trap indicates Path RDIand Path RAI(Yellow) for
DS1 interfaces. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.24 |
atmAceAlarmSectionBIPThis trap indicates Section Bit Interleave Parity. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.25 |
atmAceAlarmLineBIPThis trap indicates Line Bit Interleave Parity. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.26 |
atmAceAlarmPathBIPThis trap indicates Path Bit Interleave Parity. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.27 |
atmAceAlarmLineFEBEThis trap indicates Line Far End Block Error. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.28 |
atmAceAlarmPathFEBEThis trap indicates Path Far End Block Error. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.29 |
atmAceAlarmPlcpLOFThis trap indicates T3 PLCP Loss Of Frame. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.30 |
atmAceAlarmPlcpYELLOWThis trap indicates T3 Plcp Yellow. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.31 |
atmAceAlarmPlcpBIPThis trap indicates T3 Plcp Bit Interleave Parity. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.32 |
atmAceAlarmPlcpFEBEThis trap indicates T3 Plcp Far End Block Error. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.33 |
atmAceAlarmPlcpP1P2This trap indicates T3 Plcp Parity errors in P1/P2 bytes. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.34 |
atmAceAlarmUASThis trap is sent upon UAS start or end per port. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.35 |
atmAceAlarmClusterThis trap is sent upon atmNteAlarmType start or end,
for a cluster of VPs/VCs (according to atmNteLevel) with
the same alarm on the same physical port.
This trap replaces sending the same alarm for a big
quantity (the quantity described in the product
specification document) of VPs/VCs in order to prevent
flooding the NMS and the network with traps. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.36 |
atmAceHwFailureThis trap is sent upon HW failure per port. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.37 |
atmAceUnavailableBwTrapThis trap is sent when Bandwidth allocation is > max possible
value for the installed card.
For ACE2002 this trap will be sent for the following cases:
Card insertion - if the total Input and/or Output Bandwidth is over
allocated, then the specific card rate will be set to 0 and this trap
will be sent with the Input/Output rates values.
Upgrade from former version - when an over allocated Bandwidth is detected,
this trap will be sent with atmConfIfInputRate=atmConfIfOutputRate=0xFFFFFFFF. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.38 |
atmAceAlarmVpContinuityLossThis trap indicates Loss of Continuity Check on a VP Connection. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.40 |
atmAceAlarmVpAISReceptionThis trap indicates AIS Reception on a VP Connection. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.41 |
atmAceAlarmVpRDIReceptionThis trap indicates RDI Reception on a VP Connection. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.42 |
atmAceAlarmVpErroredCellsThis trap indicates Errored Cells on a VP Connection reported by PM. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.43 |
atmAceAlarmVpLostCellsThis trap indicates Lost Cells on a VP Connection reported by PM. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.44 |
atmAceAlarmVpMisinsertedCellsThis trap indicates Misinserted Cells on a VP Connection
reported by PM. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.45 |
atmAceAlarmVpUASThis trap is sent upon UAS start or end per VP. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.46 |
atmAceAlarmVpLoopbackThis trap is sent upon OAM LoopBack fail status per VP. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.47 |
atmAceAlarmVpGCRAViolationThis trap indicates GCRA violation on a VP Connection
reported by UPC device. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.48 |
atmAceAlarmVcContinuityLossThis trap indicates Loss of Continuity Check on a VC Connection. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.56 |
atmAceAlarmVcAISReceptionThis trap indicates AIS Reception on a VC. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.57 |
atmAceAlarmVcRDIReceptionThis trap indicates RDI Reception on a VC Connection. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.58 |
atmAceAlarmVcErroredCellsThis trap indicates Errored Cells on a VC Connection reported by PM. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.59 |
atmAceAlarmVcLostCellsThis trap indicates Lost Cells on a VC Connection reported by PM. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.60 |
atmAceAlarmVcMisinsertedCellsThis trap indicates Misinserted Cells on a VC Connection reported
by PM. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.61 |
atmAceAlarmVcUnexpectedCellThis trap indicates an unexpected cell from user or network port. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.62 |
atmAceAlarmVcUASThis trap is sent upon UAS start or end per VC. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.63 |
atmAceAlarmVcLoopbackThis trap is sent upon OAM LoopBack fail status per VC. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.64 |
atmAceAlarmVcGCRAViolationThis trap indicates GCRA violation on a VC Connection
reported by UPC device. NOTIFICATION-TYPE .1.3.6.1.4.1.164.6.1.12.0.65 |
atmGen OBJECT IDENTIFIER .2 |
atmNteLoopback OBJECT IDENTIFIER .2 |
IF-MIB Unknown .2 |
ATM-MIB NOTIFICATION-TYPE .2 |
atmAceAlarmTrapThe trap is sent whenever there is a transition from a no alarm
state to a state with at least one active alarm. An active alarm
state exists if:
1) The atmInterfaceActiveAlarms vector is different than 0.
2) The atmNteAlarmVpTable contains entries.
3) The atmNteAlarmVcTable contains entries.
The trap is also sent when a transition into the no alarm state
occurs.
The second variable will be atmInterfaceActiveAlarms to
indicate the kind of the alarm.
The trap is not sent more than once in a 10 second interval. NOTIFICATION-TYPE .2 |
atmPerfHistory OBJECT IDENTIFIER .2.1 |
atmLoopbackVpTableThis table contains parameters for an OAM VP loopback test. SEQUENCE OF AtmLoopbackVpEntry .2.1 |
atmIfPerformance OBJECT IDENTIFIER .2.1.1 |
atmLoopbackVpEntryAn entry in table atmLoopbackVpTable. AtmLoopbackVpEntry .2.1.1 |
atmIfDataTableThe ATM interface Data table. SEQUENCE OF AtmIfDataEntry .2.1.1.1 |
atmLoopbackVpIfIndexThe interface index of the ATM layer.ro Integer32 .2.1.1.1 |
atmIfDataEntryAn entry in the ATM interface Data table. AtmIfDataEntry .2.1.1.1.1 |
atmIfTimeElapsedThe number of seconds that have elapsed since
the beginning of the near end current error-
measurement period.ro Integer32 .2.1.1.1.1.1 |
atmIfValidIntervalsThe number of previous near end intervals for
which valid data was collected. The value will be
96 unless the interface was brought online within
the last 24 hours, in which case the value will be
the number of complete 15 minute near end
intervals since the interface has been online.ro Integer32 .2.1.1.1.1.2 |
atmIfCurrentTableThe ATM interface Current table. SEQUENCE OF AtmIfCurrentEntry .2.1.1.2 |
atmLoopbackVpVpiThe VPI of the OAM VPL.ro Integer32 .2.1.1.2 |
atmIfCurrentEntryAn entry in the ATM interface Current table. AtmIfCurrentEntry .2.1.1.2.1 |
atmIfCurrentTxCellsThe counter associated with the number of transmitted
cells, encountered by an ATM interface in
the current 15 minute interval.ro Gauge32 .2.1.1.2.1.1 |
atmIfCurrentRxCellsThe counter associated with the number of received
cells, encountered by an ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.1.2.1.2 |
atmIfCurrentCorrectedHecsThe counter associated with the number of cells with
corrected HEC errors, encountered by an
ATM interface in the current 15 minute
interval.ro Gauge32 .2.1.1.2.1.3 |
atmIfCurrentUncorrectedHecsThe counter associated with the number of cells with
uncorrected HEC errors, encountered by an ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.1.2.1.4 |
atmIfCurrentHecErrorSecondsThe counter associated with the number of seconds with
HEC errors, encountered by an ATM interface in
the current 15 minute interval.ro Gauge32 .2.1.1.2.1.5 |
atmIfIntervalTableThe ATM interface Interval table. SEQUENCE OF AtmIfIntervalEntry .2.1.1.3 |
atmLoopbackVpOperStatus-noActive(1) means that the loopback test has not been activated for this VP.
-inProgress(2) means that the test has been activated and there is currently no problem.
-failed(3) means there was problem during the test or after having stopped it
-endSuccessfully(4) means that the test was stopped and all was OK.ro Enumeration .2.1.1.3 |
atmIfIntervalEntryAn entry in the ATM interface Interval table. AtmIfIntervalEntry .2.1.1.3.1 |
atmIfIntervalNumberA number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes interval
(assuming that all 96 intervals are valid).ro Integer32 .2.1.1.3.1.1 |
atmIfIntervalTxCellsThe counter associated with the number of transmitted
cells , encountered by an ATM interface in
one of the previous 96, individual 15 minute,
intervals.ro Gauge32 .2.1.1.3.1.2 |
atmIfIntervalRxCellsThe counter associated with the number of received
cells, encountered by an ATM
interface in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.1.3.1.3 |
atmIfIntervalCorrectedHecsThe counter associated with the number of cells with
corrected HEC errors, encountered by an
ATM interface in one of the previous 96,
individual 15 minute, intervals.ro Gauge32 .2.1.1.3.1.4 |
atmIfIntervalUncorrectedHecsThe counter associated with the number of cells with
uncorrected HEC errors, encountered by an ATM
interface in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.1.3.1.5 |
atmIfIntervalHecErrorSecondsThe counter associated with the number of seconds with
HEC errors, encountered by an ATM interface in one of
the previous 96, individual 15 minute, intervals.ro Gauge32 .2.1.1.3.1.6 |
aal5VccXTable OBJECT IDENTIFIER .2.1.1.4 |
atmLoopbackVpCDVCell Delay Variation for this sampling.ro Integer32 .2.1.1.4 |
atmLoopbackVpAverageDelayAverage delay without including lost cells.ro Integer32 .2.1.1.5 |
atmLoopbackVpMaxDelayMaximum delay without including lost cells.ro Integer32 .2.1.1.6 |
atmLoopbackVpMinDelayMinimum delay.ro Integer32 .2.1.1.7 |
atmLoopbackVpErrSessionsErrored Sessions. Will be updated once in 5 seconds.ro Integer32 .2.1.1.8 |
atmPvcPerformance OBJECT IDENTIFIER .2.1.2 |
atmVpPerformance OBJECT IDENTIFIER .2.1.2.1 |
atmVpCurrentTableThe ATM VP Current table. SEQUENCE OF AtmVpCurrentEntry .2.1.2.1.1 |
atmVpCurrentEntryAn entry in the ATM VP Current table. AtmVpCurrentEntry .2.1.2.1.1.1 |
atmVpCurrentVpiThe VPI of the VPL.ro Integer32 .2.1.2.1.1.1.1 |
atmVpCurrentRxCellsClp01The counter associated with the number of transmitted
cells, encountered by the VPL of this ATM interface in
the current 15 minute interval.ro Gauge32 .2.1.2.1.1.1.2 |
atmVpCurrentRxCellsClp0The counter associated with the number of received
cells, encountered by the VPL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.1.1.1.3 |
atmVpCurrentGcra0ViolationsThe counter associated with the number of cells
violating GCRA0, encountered by the VPL of this
ATM interface in the current 15 minute
interval.ro Gauge32 .2.1.2.1.1.1.4 |
atmVpCurrentGcra1ViolationsThe counter associated with the number of cells
violating GCRA1, encountered by the VPL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.1.1.1.5 |
atmVpCurrentRxAISThe counter associated with the number of received
AIS cells, encountered by the VPL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.1.1.1.6 |
atmVpCurrentTxAISThe counter associated with the number of transmitted
AIS cells, encountered by the VPL of this ATM
interface in the current 15 minute interval. Not Supported
in the first phase.ro Gauge32 .2.1.2.1.1.1.7 |
atmVpCurrentRxRDIThe counter associated with the number of received
RDI cells, encountered by the VPL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.1.1.1.8 |
atmVpCurrentTxRDIThe counter associated with the number of transmitted
RDI cells, encountered by the VPL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.1.1.1.9 |
atmVpCurrentContinuityLossThe counter associated with the number of loss of
continuity cells, encountered by the VPL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.1.1.1.10 |
atmVpCurrentUASThe counter associated with the number of Unavailable
Seconds, encountered by the VPL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.1.1.1.11 |
atmVpCurrentSESThe counter associated with the number of Severerly Errored
Seconds, encountered by the VPL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.1.1.1.12 |
atmVpCurrentCDCAmount of cells dropped in the current 15 minute interval
of the VP connection.ro Gauge32 .2.1.2.1.1.1.13 |
atmVpCurrentTotalDiscardsThe total number of valid ATM cells discarded by
the traffic policing entity. This includes cells
originally received with CLP=0 and CLP=1.ro Gauge32 .2.1.2.1.1.1.14 |
atmVpCurrentClp0DiscardsThe total number of valid ATM cells received with
CLP=0 and discarded by the traffic policing
entity.ro Gauge32 .2.1.2.1.1.1.15 |
atmVpCurrentTotalCellOutsThe total number of valid ATM cells transmitted
by this VPL. This includes both CLP=0 and CLP=1
cells.ro Gauge32 .2.1.2.1.1.1.16 |
atmVpCurrentClp0CellOutsThe total number of valid ATM cells transmitted
with CLP=0 by this VPL.ro Gauge32 .2.1.2.1.1.1.17 |
atmVpCurrentTaggedOutsThe total number of valid ATM cells tagged by the
traffic policing entity from CLP=0 to CLP=1 and
transmitted by this VPL.ro Gauge32 .2.1.2.1.1.1.18 |
atmVpCurrentPCRThe maximum traffic rate encountered in the
last interval of the VP connection (monitored once a second).ro Gauge32 .2.1.2.1.1.1.19 |
atmVpCurrentSCRThe average traffic rate during the last interval of the VP
connection.ro Gauge32 .2.1.2.1.1.1.20 |
atmVpCurrentMCRMCR - The minimum traffic rate encountered in the last
interval of the VP connection (monitored once a second).ro Gauge32 .2.1.2.1.1.1.21 |
atmVpCurrentShaperTotalDiscardsThe total number of cells (CLP0 and CLP1) discarded
due to congestion by the traffic shaper.ro Gauge32 .2.1.2.1.1.1.22 |
atmVpCurrentShaperClp0DiscardsThe total number of CLP0 cells discarded
due to congestion by the traffic shaper.ro Gauge32 .2.1.2.1.1.1.23 |
atmVpCurrentShaperClp1DiscardsThe total number of CLP1 cells discarded
due to congestion by the traffic shaper.ro Gauge32 .2.1.2.1.1.1.24 |
atmVpPMCurrentTableThe ATM VP Current table for Performance Management. SEQUENCE OF AtmVpPMCurrentEntry .2.1.2.1.2 |
atmVpPMCurrentEntryAn entry in the ATM VP Current table for Performance
Management. AtmVpPMCurrentEntry .2.1.2.1.2.1 |
atmVpPMCurrentVpiThe VPI of the VPL.ro Integer32 .2.1.2.1.2.1.1 |
atmVpPMCurrentDirThe direction of performance management.ro Enumeration .2.1.2.1.2.1.2 |
atmVpPMCurrentTxClp01The counter associated with the number of transmitted
CLP 0+1 cells, encountered by the VPL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.1.2.1.3 |
atmVpPMCurrentTxClp0The counter associated with the number of transmitted
CLP 0 cells, encountered by the VPL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.1.2.1.4 |
atmVpPMCurrentRxClp01The counter associated with the number of received
CLP 0+1 cells, encountered by the VPL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.1.2.1.5 |
atmVpPMCurrentRxClp0The counter associated with the number of received
CLP 0 cells, encountered by the VPL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.1.2.1.6 |
atmVpPMCurrentErroredCellsThe counter associated with the number of errored
cells, encountered by the VPL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.1.2.1.7 |
atmVpPMCurrentLostCellsThe counter associated with the number of lost
cells, encountered by the VPL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.1.2.1.8 |
atmVpPMCurrentMisinsertedCellsThe counter associated with the number of misinserted
cells, encountered by the VPL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.1.2.1.9 |
atmVpPMCurrentECBThe counter associated with the number of ECB,
encountered by the VPL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.1.2.1.10 |
atmVpPMCurrentSECBThe counter associated with the number of SECB,
encountered by the VPL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.1.2.1.11 |
atmVpPMCurrentESThe counter associated with the number of
Errored Seconds, encountered by the VPL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.1.2.1.12 |
atmVpPMCurrentSESThe counter associated with the number of Severely
Errored Seconds, encountered by the VPL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.1.2.1.13 |
atmVpPMCurrentUASThe counter associated with the number of Unavailable
Seconds, encountered by the VPL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.1.2.1.14 |
atmVpPMCurrentIntervalQualityIf the number of errors per interval is superior to
the atmNteUPLTCR value, the quality of service of
the interval is declared as unacceptable.ro Enumeration .2.1.2.1.2.1.15 |
atmVpPMCurrentLastDayQualityIf the number of errors per 24 hours is superior to
the atmNteDPLTCR value, the quality of service of
the day is declared as degraded.ro Enumeration .2.1.2.1.2.1.16 |
atmVpIntervalTableThe ATM Vp Interval table. SEQUENCE OF AtmVpIntervalEntry .2.1.2.1.3 |
atmVpIntervalEntryAn entry in the ATM Vp Interval table. AtmVpIntervalEntry .2.1.2.1.3.1 |
atmVpIntervalVpiThe VPI of the VPL.ro Integer32 .2.1.2.1.3.1.1 |
atmVpIntervalNumberA number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes interval
(assuming that all 96 intervals are valid).ro Integer32 .2.1.2.1.3.1.2 |
atmVpIntervalRxCellsClp01The counter associated with the number of transmitted
cells , encountered by an ATM interface/VP in
one of the previous 96, individual 15 minute,
intervals.ro Gauge32 .2.1.2.1.3.1.3 |
atmVpIntervalRxCellsClp0The counter associated with the number of received
cells, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.1.3.1.4 |
atmVpIntervalGcra0ViolationsThe counter associated with the number of
cells violating GCRA0, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.1.3.1.5 |
atmVpIntervalGcra1ViolationsThe counter associated with the number of
cells violating GCRA1, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.1.3.1.6 |
atmVpIntervalRxAISThe counter associated with the number of received
AIS cells, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.1.3.1.7 |
atmVpIntervalTxAISThe counter associated with the number of transmitted
AIS cells, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals. Not supported in the first phase.ro Gauge32 .2.1.2.1.3.1.8 |
atmVpIntervalRxRDIThe counter associated with the number of received
RDI cells, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.1.3.1.9 |
atmVpIntervalTxRDIThe counter associated with the number of transmitted
RDI cells, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.1.3.1.10 |
atmVpIntervalContinuityLossThe counter associated with the number of Continuity
Loss cells, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.1.3.1.11 |
atmVpIntervalUASThe counter associated with the number of Unavailable
Seconds, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.1.3.1.12 |
atmVpIntervalSESThe counter associated with the number of Severerly Errored
Seconds, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.1.3.1.13 |
atmVpIntervalCDCAmount of cells dropped in the 15 minute interval
of the VP connection.ro Gauge32 .2.1.2.1.3.1.14 |
atmVpIntervalTotalDiscardsThe total number of valid ATM cells discarded by
the traffic policing entity. This includes cells
originally received with CLP=0 and CLP=1.ro Gauge32 .2.1.2.1.3.1.15 |
atmVpIntervalClp0DiscardsThe total number of valid ATM cells received with
CLP=0 an discarded by the traffic policing
entity.ro Gauge32 .2.1.2.1.3.1.16 |
atmVpIntervalTotalCellOutsThe total number of valid ATM cells transmitted
by this VPL. This includes both CLP=0 and CLP=1
cells.ro Gauge32 .2.1.2.1.3.1.17 |
atmVpIntervalClp0CellOutsThe total number of valid ATM cells transmitted
with CLP=0 by this VPL.ro Gauge32 .2.1.2.1.3.1.18 |
atmVpIntervalTaggedOutsThe total number of valid ATM cells tagged by the
traffic policing entity from CLP=0 to CLP=1 and
transmitted by this VPL.ro Gauge32 .2.1.2.1.3.1.19 |
atmVpIntervalPCRThe maximum traffic rate encountered in the last
interval of the VP connection (monitored once a second)
encountered by an ATM interface/VP in one of the previous
96, individual 15 minute, intervals.ro Gauge32 .2.1.2.1.3.1.20 |
atmVpIntervalSCRThe average traffic rate during the last interval of the
VP connection , encountered by an ATM interface/VP in one
of the previous 96, individual 15 minute, intervals.ro Gauge32 .2.1.2.1.3.1.21 |
atmVpIntervalMCRMCR - The minimum traffic rate encountered in the last
interval of the VP connection (monitored once a second)
encountered by an ATM interface/VP in one of the previous
96, individual 15 minute, intervals.ro Gauge32 .2.1.2.1.3.1.22 |
atmVpIntervalShaperTotalDiscardsThe total number of cells (CLP0 and CLP1) discarded
due to congestion by the traffic shaper.ro Gauge32 .2.1.2.1.3.1.23 |
atmVpIntervalShaperClp0DiscardsThe total number of CLP0 cells discarded
due to congestion by the traffic shaper.ro Gauge32 .2.1.2.1.3.1.24 |
atmVpIntervalShaperClp1DiscardsThe total number of CLP1 cells discarded
due to congestion by the traffic shaper.ro Gauge32 .2.1.2.1.3.1.25 |
atmVpPMIntervalTableThe ATM Vp Interval table for Performance Management. SEQUENCE OF AtmVpPMIntervalEntry .2.1.2.1.4 |
atmVpPMIntervalEntryAn entry in the ATM Vp Interval table for Performance
Management. AtmVpPMIntervalEntry .2.1.2.1.4.1 |
atmVpPMIntervalVpiThe VPI of the VPL.ro Integer32 .2.1.2.1.4.1.1 |
atmVpPMIntervalDirThe direction of performance management.ro Enumeration .2.1.2.1.4.1.2 |
atmVpPMIntervalNumberA number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes interval
(assuming that all 96 intervals are valid).ro Integer32 .2.1.2.1.4.1.3 |
atmVpPMIntervalTxClp01The counter associated with the number of transmitted
CLP 0+1 cells, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.1.4.1.4 |
atmVpPMIntervalTxClp0The counter associated with the number of transmitted
CLP 0 cells, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.1.4.1.5 |
atmVpPMIntervalRxClp01The counter associated with the number of received
CLP 0+1 cells, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.1.4.1.6 |
atmVpPMIntervalRxClp0The counter associated with the number of received
CLP 0 cells, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.1.4.1.7 |
atmVpPMIntervalErroredCellsThe counter associated with the number of Errored
cells, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.1.4.1.8 |
atmVpPMIntervalLostCellsThe counter associated with the number of Lost
cells, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.1.4.1.9 |
atmVpPMIntervalMisinsertedCellsThe counter associated with the number of Misinserted
cells, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.1.4.1.10 |
atmVpPMIntervalECBThe counter associated with the number of ECBs
encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.1.4.1.11 |
atmVpPMIntervalSECBThe counter associated with the number of SECBs
encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.1.4.1.12 |
atmVpPMIntervalESThe counter associated with the number of Errored
Seconds, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.1.4.1.13 |
atmVpPMIntervalSESThe counter associated with the number of Severely
Errored Seconds, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.1.4.1.14 |
atmVpPMIntervalUASThe counter associated with the number of Unavailable
Seconds, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.1.4.1.15 |
atmVpPMIntervalQualityIf the number of errors per interval is superior to
the atmNteUPLTCR value, the quality of service of
the interval is declared as unacceptable.ro Enumeration .2.1.2.1.4.1.16 |
atmVpPMIntervalLastDayQualityIf the number of errors per 24 hours is superior to
the atmNteDPLTCR value, the quality of service of
the day is declared as degraded.ro Enumeration .2.1.2.1.4.1.17 |
atmVpQoSTableThe VP QoS table. SEQUENCE OF AtmVpQoSEntry .2.1.2.1.5 |
atmVpQoSEntry. AtmVpQoSEntry .2.1.2.1.5.1 |
atmVpQoSPeriodRefThis object is an index that specifies which period of time, the next
2 objects refer to.
currentPeriod - the period since last systemResetAllStatsCmd received or
since Start-up (if no systemResetAllStatsCmd was received since
Start-up) until now.
lastPeriod - the period between last two commands of systemResetAllStatsCmd.
- If only one command occurred since Start-up: the period between
Start-up and last command.
- If no command occurred since Start-up: this period will not
actually exist. In this case, he following 5 objects will be 0.ro Enumeration .2.1.2.1.5.1.1 |
atmVpQoSElapsedTimeElapsed Time in seconds.
- for atmVpQoSPeriodRef = currentPeriod:
The period since last systemResetAllStatsCmd received or since Start-up
(if no systemResetAllStatsCmd was received since Start-up) until now.
- for atmVpQoSPeriodRef = lastPeriod:
The value of atmVpQoSElapsedTime when last systemResetAllStatsCmd
was received.ro Integer32 .2.1.2.1.5.1.2 |
atmVpQoSUASNumber of Unavailable Seconds for the reference period (atmVpQoSPeriodRef).ro Gauge32 .2.1.2.1.5.1.3 |
atmVpPMQoSTableThe PM VP QoS table. SEQUENCE OF AtmVpPMQoSEntry .2.1.2.1.6 |
atmVpPMQoSEntry. AtmVpPMQoSEntry .2.1.2.1.6.1 |
atmVpPMQoSDirectionThe direction of performance management.ro Enumeration .2.1.2.1.6.1.1 |
atmVpPMQoSPeriodRefThis object is an index that specifies which period of time, the next
5 objects refer to.
currentPeriod - the period since last systemResetAllStatsCmd received or
since Start-up (if no systemResetAllStatsCmd was received since
Start-up) until now.
lastPeriod - the period between last two commands of systemResetAllStatsCmd.
- If only one command occurred since Start-up: the period between
Start-up and last command.
- If no command occurred since Start-up: this period will not
actually exist. In this case, he following 5 objects will be 0.ro Enumeration .2.1.2.1.6.1.2 |
atmVpPMQoSCLRCell Loss Ratio counter for the reference period (atmVpPMQoSPeriodRef)-
defined in accordance with I.356 , in %.
The value will be multipuled by 100.ro Gauge32 .2.1.2.1.6.1.3 |
atmVpPMQoSCERCell Error Ratio counter for the reference period (atmVpPMQoSPeriodRef)
defined in accordance with I.356 , in %.
The value will be multipuled by 100.ro Gauge32 .2.1.2.1.6.1.4 |
atmVpPMQoSCMRCell Misinsertion Ratio counter for the reference period (atmVpPMQoSPeriodRef)
defined in accordance with I.356 , cells/sec .ro Gauge32 .2.1.2.1.6.1.5 |
atmVpShaperStatTableThe ATM VP shaper statistics table. SEQUENCE OF AtmVpShaperStatEntry .2.1.2.1.7 |
atmVpShaperStatEntryAn entry in the ATM VP shaper statistics table. AtmVpShaperStatEntry .2.1.2.1.7.1 |
atmVpShaperDiscardedThe number of Cells that were discarded in the shaper on that VPC due
to buffer overflow.
This counter counts till it reaches its MAX value (20 bits) and then
rolls over.ro Counter32 .2.1.2.1.7.1.1 |
atmVpShaperOccupationThe number of Cells that are currently stored in the buffer.
This parameter is limited to 20 bits.ro Integer32 .2.1.2.1.7.1.2 |
atmVpShaperMaxOccupationThe Maximum number of Cells that were stored in the buffer,
since this VP was activated. This parameter is limited to 20 bits.ro Integer32 .2.1.2.1.7.1.3 |
atmVpShaperLevelThe occupation of the buffer according to a predefined threshold.
empty - buffer is Empty
full - buffer is Full
below - buffer is Below the threshold
above - buffer is Above the threshold. This is also the trigger to
start EPD\PPD mechanism, if set for the VPC.ro Enumeration .2.1.2.1.7.1.4 |
atmVpShaperEpdDroppedThe number of Cells that were dropped in the shaper on that VPC
due to EPD\PPD mechanism in the last second.
This parameter is limited to 24 bits.
Applicable for a EPD/PPD VP only.ro Counter32 .2.1.2.1.7.1.5 |
atmVpShaperTotalEpdDroppedThe Total number of Cells that were dropped in the shaper on that
VPC due to EPD\PPD mechanism in the last 15 minutes. This counter
automatically reset itself every 15 minutes.
Applicable for a EPD/PPD VP only.ro Counter32 .2.1.2.1.7.1.6 |
atmVcPerformance OBJECT IDENTIFIER .2.1.2.2 |
atmVcCurrentTableThe ATM VC Current table. SEQUENCE OF AtmVcCurrentEntry .2.1.2.2.1 |
atmVcCurrentEntryAn entry in the ATM VC Current table. AtmVcCurrentEntry .2.1.2.2.1.1 |
atmVcCurrentVpiThe VPI of the VCL.ro Integer32 .2.1.2.2.1.1.1 |
atmVcCurrentVciThe VCI of the VCL.ro Integer32 .2.1.2.2.1.1.2 |
atmVcCurrentRxCellsClp01The counter associated with the number of transmitted
cells, encountered by the VCL of this ATM interface in
the current 15 minute interval.ro Gauge32 .2.1.2.2.1.1.3 |
atmVcCurrentRxCellsClp0The counter associated with the number of received
cells, encountered by the VCL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.2.1.1.4 |
atmVcCurrentGcra0ViolationsThe counter associated with the number of cells
violating GCRA0, encountered by the VCL of this
ATM interface in the current 15 minute
interval.ro Gauge32 .2.1.2.2.1.1.5 |
atmVcCurrentGcra1ViolationsThe counter associated with the number of cells
violating GCRA1, encountered by the VCL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.2.1.1.6 |
atmVcCurrentRxAISThe counter associated with the number of received
AIS cells, encountered by the VCL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.2.1.1.7 |
atmVcCurrentTxAISThe counter associated with the number of transmitted
AIS cells, encountered by the VCL of this ATM
interface in the current 15 minute interval. Not Supported
in the first phase.ro Gauge32 .2.1.2.2.1.1.8 |
atmVcCurrentRxRDIThe counter associated with the number of received
RDI cells, encountered by the VCL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.2.1.1.9 |
atmVcCurrentTxRDIThe counter associated with the number of transmitted
RDI cells, encountered by the VCL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.2.1.1.10 |
atmVcCurrentContinuityLossThe counter associated with the number of loss of
continuity cells, encountered by the VCL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.2.1.1.11 |
atmVcCurrentUASThe counter associated with the number of Unavailable
Seconds, encountered by the VCL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.2.1.1.12 |
atmVcCurrentSESThe counter associated with the number of Severerly Errored
Seconds, encountered by the VCL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.2.1.1.13 |
atmVcCurrentCDCAmount of cells dropped in the current 15 minute interval
of the VC connection.ro Gauge32 .2.1.2.2.1.1.14 |
atmVcCurrentTotalDiscardsThe total number of valid ATM cells discarded by
the traffic policing entity. This includes cells
originally received with CLP=0 and CLP=1.ro Gauge32 .2.1.2.2.1.1.15 |
atmVcCurrentClp0DiscardsThe total number of valid ATM cells received with
CLP=0 an discarded by the traffic policing
entity.ro Gauge32 .2.1.2.2.1.1.16 |
atmVcCurrentTotalCellOutsThe total number of valid ATM cells transmitted
by this VPL. This includes both CLP=0 and CLP=1
cells.ro Gauge32 .2.1.2.2.1.1.17 |
atmVcCurrentClp0CellOutsThe total number of valid ATM cells transmitted
with CLP=0 by this VPL.ro Gauge32 .2.1.2.2.1.1.18 |
atmVcCurrentTaggedOutsThe total number of valid ATM cells tagged by the
traffic policing entity from CLP=0 to CLP=1 and
transmitted by this VPL.ro Gauge32 .2.1.2.2.1.1.19 |
atmVcCurrentPCRThe maximum traffic rate encountered in the last
interval of the VC connection (monitored once a second).ro Gauge32 .2.1.2.2.1.1.20 |
atmVcCurrentSCRThe average traffic rate during the last interval
of the VC connection.ro Gauge32 .2.1.2.2.1.1.21 |
atmVcCurrentMCRMCR - The minimum traffic rate encountered in the last
interval of the VC connection (monitored once a second).ro Gauge32 .2.1.2.2.1.1.22 |
atmVcCurrentShaperTotalDiscardsThe total number of cells (CLP0 and CLP1) discarded
due to congestion by the traffic shaper.ro Gauge32 .2.1.2.2.1.1.23 |
atmVcCurrentShaperClp0DiscardsThe total number of CLP0 cells discarded
due to congestion by the traffic shaper.ro Gauge32 .2.1.2.2.1.1.24 |
atmVcCurrentShaperClp1DiscardsThe total number of CLP1 cells discarded
due to congestion by the traffic shaper.ro Gauge32 .2.1.2.2.1.1.25 |
atmVcPMCurrentTableThe ATM VC Current table for Performance Management. SEQUENCE OF AtmVcPMCurrentEntry .2.1.2.2.2 |
atmVcPMCurrentEntryAn entry in the ATM VC Current table for Performance
Management. AtmVcPMCurrentEntry .2.1.2.2.2.1 |
atmVcPMCurrentVpiThe VPI of the VCL.ro Integer32 .2.1.2.2.2.1.1 |
atmVcPMCurrentVciThe VCI of the VCL.ro Integer32 .2.1.2.2.2.1.2 |
atmVcPMCurrentDirThe direction of Performance Management.ro Integer32 .2.1.2.2.2.1.3 |
atmVcPMCurrentTxClp01The counter associated with the number of transmitted
CLP 0+1 cells, encountered by the VCL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.2.2.1.4 |
atmVcPMCurrentTxClp0The counter associated with the number of transmitted
CLP 0 cells, encountered by the VCL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.2.2.1.5 |
atmVcPMCurrentRxClp01The counter associated with the number of received
CLP 0+1 cells, encountered by the VCL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.2.2.1.6 |
atmVcPMCurrentRxClp0The counter associated with the number of received
CLP 0 cells, encountered by the VCL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.2.2.1.7 |
atmVcPMCurrentErroredCellsThe counter associated with the number of errored
cells, encountered by the VCL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.2.2.1.8 |
atmVcPMCurrentLostCellsThe counter associated with the number of lost
cells, encountered by the VCL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.2.2.1.9 |
atmVcPMCurrentMisinsertedCellsThe counter associated with the number of misinserted
cells, encountered by the VCL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.2.2.1.10 |
atmVcPMCurrentECBThe counter associated with the number of ECBs
encountered by the VCL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.2.2.1.11 |
atmVcPMCurrentSECBThe counter associated with the number of SECBs
encountered by the VCL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.2.2.1.12 |
atmVcPMCurrentESThe counter associated with the number of
Errored Seconds, encountered by the VCL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.2.2.1.13 |
atmVcPMCurrentSESThe counter associated with the number of Severely
Errored Seconds, encountered by the VCL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.2.2.1.14 |
atmVcPMCurrentUASThe counter associated with the number of Severely
Errored Seconds, encountered by the VCL of this ATM
interface in the current 15 minute interval.ro Gauge32 .2.1.2.2.2.1.15 |
atmVcPMCurrentIntervalQualityIf the number of errors per interval is superior to
the atmNteUPLTCR value, the quality of service of
the interval is declared as unacceptable.ro Enumeration .2.1.2.2.2.1.16 |
atmVcPMCurrentLastDayQualityIf the number of errors per 24 hours is superior to
the atmNteDPLTCR value, the quality of service of
the day is declared as degraded.ro Enumeration .2.1.2.2.2.1.17 |
atmVcIntervalTableThe ATM Vc Interval table. SEQUENCE OF AtmVcIntervalEntry .2.1.2.2.3 |
atmVcIntervalEntryAn entry in the ATM Vc Interval table. AtmVcIntervalEntry .2.1.2.2.3.1 |
atmVcIntervalVpiThe VPI of the VCL.ro Integer32 .2.1.2.2.3.1.1 |
atmVcIntervalVciThe VCI of the VCL.ro Integer32 .2.1.2.2.3.1.2 |
atmVcIntervalNumberA number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes interval
(assuming that all 96 intervals are valid).ro Integer32 .2.1.2.2.3.1.3 |
atmVcIntervalRxCellsClp01The counter associated with the number of transmitted
cells , encountered by an ATM interface/VC in
one of the previous 96, individual 15 minute,
intervals.ro Gauge32 .2.1.2.2.3.1.4 |
atmVcIntervalRxCellsClp0The counter associated with the number of received
cells, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.2.3.1.5 |
atmVcIntervalGcra0ViolationsThe counter associated with the number of
cells violating GCRA0, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.2.3.1.6 |
atmVcIntervalGcra1ViolationsThe counter associated with the number of
cells violating GCRA1, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.2.3.1.7 |
atmVcIntervalRxAISThe counter associated with the number of received
AIS cells, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.2.3.1.8 |
atmVcIntervalTxAISThe counter associated with the number of transmitted
AIS cells, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals. Not supported in the first phase.ro Gauge32 .2.1.2.2.3.1.9 |
atmVcIntervalRxRDIThe counter associated with the number of received
RDI cells, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.2.3.1.10 |
atmVcIntervalTxRDIThe counter associated with the number of transmitted
RDI cells, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.2.3.1.11 |
atmVcIntervalContinuityLossThe counter associated with the number of Continuity
Loss cells, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.2.3.1.12 |
atmVcIntervalUASThe counter associated with the number of Unavailable
Seconds, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.2.3.1.13 |
atmVcIntervalSESThe counter associated with the number of Severerly Errored
Seconds, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.2.3.1.14 |
atmVcIntervalCDCAmount of cells dropped in the 15 minute interval
of the VC connection.ro Gauge32 .2.1.2.2.3.1.15 |
atmVcIntervalTotalDiscardsThe total number of valid ATM cells discarded by
the traffic policing entity. This includes cells
originally received with CLP=0 and CLP=1.ro Gauge32 .2.1.2.2.3.1.16 |
atmVcIntervalClp0DiscardsThe total number of valid ATM cells received with
CLP=0 an discarded by the traffic policing
entity.ro Gauge32 .2.1.2.2.3.1.17 |
atmVcIntervalTotalCellOutsThe total number of valid ATM cells transmitted
by this VPL. This includes both CLP=0 and CLP=1
cells.ro Gauge32 .2.1.2.2.3.1.18 |
atmVcIntervalClp0CellOutsThe total number of valid ATM cells transmitted
with CLP=0 by this VPL.ro Gauge32 .2.1.2.2.3.1.19 |
atmVcIntervalTaggedOutsThe total number of valid ATM cells tagged by the
traffic policing entity from CLP=0 to CLP=1 and
transmitted by this VPL.ro Gauge32 .2.1.2.2.3.1.20 |
atmVcIntervalPCRThe maximum traffic rate encountered in the
last interval of the VC connection (monitored once a second)
encountered by an ATM interface/VC in one of the previous 96,
individual 15 minute, intervals.ro Gauge32 .2.1.2.2.3.1.21 |
atmVcIntervalSCRThe average traffic rate during the last interval
of the VC connection, encountered by an ATM interface/VC
in one of the previous 96, individual 15 minute, intervals.ro Gauge32 .2.1.2.2.3.1.22 |
atmVcIntervalMCRMCR - The minimum traffic rate encountered in the last
interval of the VC connection (monitored once a second)
encountered by an ATM interface/VC in one of the previous 96,
individual 15 minute, intervals.ro Gauge32 .2.1.2.2.3.1.23 |
atmVcIntervalShaperTotalDiscardsThe total number of cells (CLP0 and CLP1) discarded
due to congestion by the traffic shaper.ro Gauge32 .2.1.2.2.3.1.24 |
atmVcIntervalShaperClp0DiscardsThe total number of CLP0 cells discarded
due to congestion by the traffic shaper.ro Gauge32 .2.1.2.2.3.1.25 |
atmVcIntervalShaperClp1DiscardsThe total number of CLP1 cells discarded
due to congestion by the traffic shaper.ro Gauge32 .2.1.2.2.3.1.26 |
atmVcPMIntervalTableThe ATM Vc Interval table for Performance Management. SEQUENCE OF AtmVcPMIntervalEntry .2.1.2.2.4 |
atmVcPMIntervalEntryAn entry in the ATM Vc Interval table for Performance
Management. AtmVcPMIntervalEntry .2.1.2.2.4.1 |
atmVcPMIntervalVpiThe VPI of the VCL.ro Integer32 .2.1.2.2.4.1.1 |
atmVcPMIntervalVciThe VCI of the VCL.ro Integer32 .2.1.2.2.4.1.2 |
atmVcPMIntervalDirThe direction of Performance Management.ro Enumeration .2.1.2.2.4.1.3 |
atmVcPMIntervalNumberA number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes interval
(assuming that all 96 intervals are valid).ro Integer32 .2.1.2.2.4.1.4 |
atmVcPMIntervalTxClp01The counter associated with the number of transmitted
CLP 0+1 cells, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.2.4.1.5 |
atmVcPMIntervalTxClp0The counter associated with the number of transmitted
CLP 0 cells, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.2.4.1.6 |
atmVcPMIntervalRxClp01The counter associated with the number of received
CLP 0+1 cells, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.2.4.1.7 |
atmVcPMIntervalRxClp0The counter associated with the number of received
CLP 0 cells, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.2.4.1.8 |
atmVcPMIntervalErroredCellsThe counter associated with the number of Errored
cells, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.2.4.1.9 |
atmVcPMIntervalLostCellsThe counter associated with the number of Lost
cells, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.2.4.1.10 |
atmVcPMIntervalMisinsertedCellsThe counter associated with the number of Misinserted
cells, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.2.4.1.11 |
atmVcPMIntervalECBThe counter associated with the number of ECBs
encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.2.4.1.12 |
atmVcPMIntervalSECBThe counter associated with the number of SECBs
encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.2.4.1.13 |
atmVcPMIntervalESThe counter associated with the number of Errored
Seconds, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.2.4.1.14 |
atmVcPMIntervalSESThe counter associated with the number of Severely
Errored Seconds, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.2.4.1.15 |
atmVcPMIntervalUASThe counter associated with the number of Unavailable
Seconds, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.ro Gauge32 .2.1.2.2.4.1.16 |
atmVcPMIntervalQualityIf the number of errors per interval is superior to
the atmNteUPLTCR value, the quality of service of
the interval is declared as unacceptable.ro Enumeration .2.1.2.2.4.1.17 |
atmVcPMIntervalLastDayQualityIf the number of errors per 24 hours is superior to
the atmNteDPLTCR value, the quality of service of
the day is declared as degraded.ro Enumeration .2.1.2.2.4.1.18 |
atmCESAAL1StatsTableThis table shows statistics of the structured Circuit-Emulation connections. SEQUENCE OF AtmCESAAL1StatsEntry .2.1.2.2.5 |
atmCESAAL1StatsEntrydefines an entry in the atmCESAAL1StatsTable AtmCESAAL1StatsEntry .2.1.2.2.5.1 |
atmCESAAL1SeqErrorsnumber of cells discarded due to wrong sequence numberro Counter32 .2.1.2.2.5.1.1 |
atmCESAAL1HdrErrorsnumber of cells discarded due to bad AAL1 header error.
this include correctable and uncorrectable CRC, plus bad parity.ro Counter32 .2.1.2.2.5.1.2 |
atmCESAAL1PointerReframesnumber of events in which the AAL1 reassembler found that an SDT pointer isn't
where it is expected, and the pointer must be reacquired.ro Counter32 .2.1.2.2.5.1.3 |
atmCESAAL1BufUnderflowsnumber of buffer underflows events.ro Counter32 .2.1.2.2.5.1.4 |
atmCESAAL1BufOverflowsnumber of buffer overflows events.ro Counter32 .2.1.2.2.5.1.5 |
atmVcQoSTableThe ATM VP QoS table. SEQUENCE OF AtmVcQoSEntry .2.1.2.2.6 |
atmVcQoSEntryAn entry in the ATM VP table. AtmVcQoSEntry .2.1.2.2.6.1 |
atmVcQoSPeriodRefThis object is an index that specifies which period of time, the next
2 objects refer to.
currentPeriod - the period since last systemResetAllStatsCmd received or
since Start-up (if no systemResetAllStatsCmd was received since
Start-up) until now.
lastPeriod - the period between last two commands of systemResetAllStatsCmd.
- If only one command occurred since Start-up: the period between
Start-up and last command.
- If no command occurred since Start-up: this period will not
actually exist. In this case, he following 5 objects will be 0.ro Enumeration .2.1.2.2.6.1.1 |
atmVcQoSElapsedTimeElapsed Time in seconds.
- for atmVcQoSPeriodRef = currentPeriod:
The period since last systemResetAllStatsCmd received or since Start-up
(if no systemResetAllStatsCmd was received since Start-up) until now.
- for atmVcQoSPeriodRef = lastPeriod:
The value of atmVcQoSElapsedTime when last systemResetAllStatsCmd
was received.ro Integer32 .2.1.2.2.6.1.2 |
atmVcQoSUASNumber of Unavailable Seconds for the reference period (atmVcQoSPeriodRef).ro Gauge32 .2.1.2.2.6.1.3 |
atmVcPMQoSTableThe PM VC QoS table. SEQUENCE OF AtmVcPMQoSEntry .2.1.2.2.7 |
atmVcPMQoSEntryAn entry in the VC PM QoS table. AtmVcPMQoSEntry .2.1.2.2.7.1 |
atmVcPMQoSDirectionThe direction of performance management.ro Enumeration .2.1.2.2.7.1.1 |
atmVcPMQoSPeriodRefThis object is an index that specifies which period of time, the next
5 objects refer to.
currentPeriod - the period since last systemResetAllStatsCmd received or
since Start-up (if no systemResetAllStatsCmd was received since
Start-up) until now.
lastPeriod - the period between last two commands of systemResetAllStatsCmd.
- If only one command occurred since Start-up: the period between
Start-up and last command.
- If no command occurred since Start-up: this period will not
actually exist. In this case, he following 5 objects will be 0.ro Enumeration .2.1.2.2.7.1.2 |
atmVcPMQoSCLRCell Loss Ratio counter for the reference period (atmVcPMQoSPeriodRef)-
defined in accordance with I.356 , in %.
The value will be multipuled by 100.ro Gauge32 .2.1.2.2.7.1.3 |
atmVcPMQoSCERCell Error Ratio counter for the reference period (atmVcPMQoSPeriodRef)
defined in accordance with I.356 , in %.
The value will be multipuled by 100.ro Gauge32 .2.1.2.2.7.1.4 |
atmVcPMQoSCMRCell Miss-insertion Ratio counter for the reference period (atmVcPMQoSPeriodRef)
defined in accordance with I.356 , cells/sec .ro Gauge32 .2.1.2.2.7.1.5 |
atmVcShaperStatTableThe ATM VC shaper statistics table. SEQUENCE OF AtmVcShaperStatEntry .2.1.2.2.8 |
atmVcShaperStatEntryAn entry in the ATM VC shaper statistics table. AtmVcShaperStatEntry .2.1.2.2.8.1 |
atmVcShaperDiscardedThe number of Cells that were discarded in the shaper on that VCC due
to buffer overflow. This counter counts till it reaches its MAX value
(20 bits) and then rolls over.ro Counter32 .2.1.2.2.8.1.1 |
atmVcShaperOccupationThe number of Cells that are currently stored in the buffer.
This parameter is limited to 20 bits.ro Integer32 .2.1.2.2.8.1.2 |
atmVcShaperMaxOccupationThe Maximum number of Cells that were stored in the buffer,
since this VC was activated. This parameter is limited to 20 bits.ro Integer32 .2.1.2.2.8.1.3 |
atmVcShaperLevelThe occupation of the buffer according to a predefined threshold.
empty - buffer is Empty
full - buffer is Full
below - buffer is Below the threshold
above - buffer is Above the threshold. This is also the trigger to
start EPD\PPD mechanism, if set for the VCC.ro Enumeration .2.1.2.2.8.1.4 |
atmVcShaperEpdDroppedThe number of Cells that were dropped in the shaper on that VCC
due to EPD\PPD mechanism in the last second.
This parameter is limited to 24 bits.
Applicable for a EPD/PPD VC only.ro Counter32 .2.1.2.2.8.1.5 |
atmVcShaperTotalEpdDroppedThe Total number of Cells that were dropped in the shaper on that
VPC due to EPD\PPD mechanism in the last 15 minutes. This counter
automatically reset itself every 15 minutes.
Applicable for a EPD/PPD VC only.ro Counter32 .2.1.2.2.8.1.6 |
atmIntervalDateTableThe agent will keep in this group the date & time
corresponding to each interval. SEQUENCE OF AtmIntervalDateEntry .2.1.3 |
atmIntervalDateEntryThe date & time for the given interval. AtmIntervalDateEntry .2.1.3.1 |
atmIntervalDateIntervalThe interval number defining this entry.ro Integer32 .2.1.3.1.1 |
atmIntervalDateDateThe date corresponding to this interval.ro DisplayString (SNMPv2-TC) .2.1.3.1.2 |
atmIntervalDateTimeThe time corresponding to this interval.ro DisplayString (SNMPv2-TC) .2.1.3.1.3 |
atmGenSystem OBJECT IDENTIFIER .2.2 |
atmLoopbackVcTableThis table contains parameters for an OAM VC loopback test. SEQUENCE OF AtmLoopbackVcEntry .2.2 |
atmGenSysGen OBJECT IDENTIFIER .2.2.1 |
atmLoopbackVcEntryAn entry in table. AtmLoopbackVcEntry .2.2.1 |
atmLoopbackVcIfIndexThe interface index of the ATM layer.ro Integer32 .2.2.1.1 |
atmGenSysSelfTestTableA table containing the results of the initial testing of the device. SEQUENCE OF AtmGenSysSelfTestEntry .2.2.1.1 |
atmGenSysSelfTestEntryAn entry in table. AtmGenSysSelfTestEntry .2.2.1.1.1 |
atmGenSysSelfTestIndexA running index for the table.ro Integer32 .2.2.1.1.1.1 |
atmGenSysSelfTestResultThe results of the initial testing of the device.ro DisplayString (SNMPv2-TC) .2.2.1.1.1.2 |
atmLoopbackVcVpiThe VPI of the OAM VCL.ro Integer32 .2.2.1.2 |
atmGenSysLogClearAllSetting the variable to clear(3) removes all entries in the
Log Buffer of the agent. The agent will immediately
reset the variable to off(2).rw Enumeration .2.2.1.2 |
atmLoopbackVcVciThe VCI of the OAM VCL.ro Integer32 .2.2.1.3 |
atmGenSysLogTableA copy of the log buffer. SEQUENCE OF AtmGenSysLogEntry .2.2.1.3 |
atmGenSysLogEntryAn entry in table. AtmGenSysLogEntry .2.2.1.3.1 |
atmGenSysLogIndexThe index of the log buffer.ro Integer32 .2.2.1.3.1.1 |
atmGenSysLogMessageThe log buffer entry message text.ro DisplayString .2.2.1.3.1.2 |
atmLoopbackVcOperStatus-noActive(1) means that the loopback test has not been activated for this VP.
-inProgress(2) means that the test has been activated and there is currently no problem.
-failed(3) means there was problem during the test or after having stopped it
-endSuccessfully(4) means that the test was stopped and all was OK.ro Enumeration .2.2.1.4 |
atmGenSysSetDefaultConfgWhen set to on(3), the agent will set all the configuration parameters
to their default values. The variable is then reset to off(2)
by the agent. The agent must be reset for the default configuration
to apply.rw Enumeration .2.2.1.4 |
atmLoopbackVcCDVCell Delay Variation for this sampling.ro Integer32 .2.2.1.5 |
atmGenSysCxRefTableA Cross Reference table. The table maintains
an index of an object which is also the table index,
and a counter that indicates how many times this
object was referenced.
When using this table for more than one referenced table,
which uses the same range of indexes, then the index
should be shifted by a unique offset per table.
In ACE2002 this table is used for TD and for FR Desc. Thus,
the index for FR Descriptor is: FR Descriptor index + offset.
The offset is described in the ACE2002 NMS SRS. SEQUENCE OF AtmGenSysCxRefEntry .2.2.1.5 |
atmGenSysCxRefEntryThe entries will be added by the agent upon
an entry addition in the referenced tables
(TD table, FR Descriptor etc.) AtmGenSysCxRefEntry .2.2.1.5.1 |
atmGenSysCxRefIndexThe index specifies an entry in the table of the object.ro Integer32 .2.2.1.5.1.1 |
atmGenSysCxRefCounterThe counter counts the number of references
that have been made to the object .ro Gauge32 .2.2.1.5.1.2 |
atmLoopbackVcAverageDelayAverage delay without including lost cells.ro Integer32 .2.2.1.6 |
atmLoopbackVcMaxDelayThe maximum delay without including lost cells.ro Integer32 .2.2.1.7 |
atmLoopbackVcMinDelayThe minimum delay.ro Integer32 .2.2.1.8 |
atmLoopbackVcErrSessionsErrored Sessions. Will be updated once in 5 seconds.ro Integer32 .2.2.1.9 |
atmLoopbackVpIvlTableThis table contains parameters for an OAM VP loopback test,
according interval number. SEQUENCE OF AtmLoopbackVpIvlEntry .2.3 |
atmLoopbackVpIvlEntryAn entry in table. AtmLoopbackVpIvlEntry .2.3.1 |
atmLoopbackVpIvlIfIndexThe interface index of the ATM layer.ro Integer32 .2.3.1.1 |
atmLoopbackVpIvlVpiThe VPI of the OAM VPL.ro Integer32 .2.3.1.2 |
atmLoopbackVpIvlIvlThe relevant interval number.ro Integer32 .2.3.1.3 |
atmLoopbackVpIvlOperStatus-noActive(1) means that the loopback test has not been activated for this VP during this interval.
-inProgress(2) has no meaning for an ended interval.
-failed(3) means there was problem during the test or after having stopped it
-endSuccessfully(4) means that the test was OK.ro Enumeration .2.3.1.4 |
atmLoopbackVpIvlCDVCell Delay Variation for this interval.ro Integer32 .2.3.1.5 |
atmLoopbackVpIvlAverageDelayAverage delay without including lost cells for this interval.ro Integer32 .2.3.1.6 |
atmLoopbackVpIvlMaxDelayThe maximum delay without including lost cells for this interval.ro Integer32 .2.3.1.7 |
atmLoopbackVpIvlMinDelayThe minimum delay for this interval.ro Integer32 .2.3.1.8 |
atmLoopbackVpIvlErrSessionsErrored Sessions. Will be updated once in 5 seconds.ro Integer32 .2.3.1.9 |
atmLoopbackVcIvlTableThis table contains parameters for an OAM VC loopback test. SEQUENCE OF AtmLoopbackVcIvlEntry .2.4 |
atmLoopbackVcIvlEntryAn entry in table. AtmLoopbackVcIvlEntry .2.4.1 |
atmLoopbackVcIvlIfIndexThe interface index of the ATM layer.ro Integer32 .2.4.1.1 |
atmLoopbackVcIvlVpiThe VPI of the OAM VCL.ro Integer32 .2.4.1.2 |
atmLoopbackVcIvlVciThe VCI of the OAM VCL.ro Integer32 .2.4.1.3 |
atmLoopbackVcIvlIvlThe relevant interval number.ro Integer32 .2.4.1.4 |
atmLoopbackVcIvlOperStatus-noActive(1) means that the loopback test has not been activated for this VC during this interval.
-inProgress(2) has no meaning per interval.
-failed(3) means there was problem for this test during this interval.
-endSuccessfully(4) means that the test was OK.ro Enumeration .2.4.1.5 |
atmLoopbackVcIvlCDVCell Delay Variation for this interval.ro Integer32 .2.4.1.6 |
atmLoopbackVcIvlAverageDelayAverage delay without including lost cells.ro Integer32 .2.4.1.7 |
atmLoopbackVcIvlMaxDelayThe maximum delay without including lost cells.ro Integer32 .2.4.1.8 |
atmLoopbackVcIvlMinDelayThe minimum delay.ro Integer32 .2.4.1.9 |
atmLoopbackVcIvlErrSessionsErrored Sessions. Will be updated once in 5 seconds.ro Integer32 .2.4.1.10 |
atmNtePM OBJECT IDENTIFIER .3 |
atmNteMdl OBJECT IDENTIFIER .3 |
atmAceModuleChangeTrapThe trap is sent every time a module is changed (Hot swapping).
The second variable will be atmNteCardType to indicate the
type of card that was inserted. The value empty(255) indicates that
a card was taken out. NOTIFICATION-TYPE .3 |
atmNteMdlConfig OBJECT IDENTIFIER .3.1 |
atmVpPmTableThis table contains parameters for VP performance monitoring. SEQUENCE OF AtmVpPmEntry .3.1 |
atmVpPmEntryAn entry in table. AtmVpPmEntry .3.1.1 |
atmNteMdlConfigTableModule configuration table. SEQUENCE OF AtmNteMdlConfigEntry .3.1.1 |
atmVpPmIfIndexThe interface index of the ATM layer.ro Integer32 .3.1.1.1 |
atmNteMdlConfigEntryThere is an entry in this table just for those modules that have
parameters that are relevant to module level only. AtmNteMdlConfigEntry .3.1.1.1 |
atmNteMdlSlotIndexThe slot number. Integer32 .3.1.1.1.1 |
atmNteMdlPrtCpuSharingThis object lets the user decide what will be the CPU sharing
between the ports of the module. This object is applicable for
modules in which the same CPU handles the traffic of all ports.
equal - All ports will have the same CPU resource.
port1 - Port 1 will have higher priority than the other ports.rw Enumeration .3.1.1.1.2 |
atmNteMdlInputPriorityMechanismThis object allows the user to Enable/Disable the Input priority mechanism.
This object is applicable for modules with more than one port, in which the
total ports input may be greater than the port output.
disabled - all LAN VCCs will be transmitted through the same queue (queue 1).
Upon congestion frames will be dropped randomly.
enabled - the user should configure each port/connection priority. Upon
congestion frames will be dropped according to priority.rw Enumeration .3.1.1.1.3 |
atmVpPmVpiThe VPI of the Performance Monitoring VPL.ro Integer32 .3.1.1.2 |
atmVpPmAdminStatusup(2) - Activate PM.
down(3) - Deactivate PM.
listenToActivationCells(4) - .
originateActivationCells(5) - .rw Enumeration .3.1.1.3 |
atmVpPmDirectionThe direction of PM.rw Enumeration .3.1.1.4 |
atmVpPmBlockSizeValid block sizes (in cells): 128, 256, 512, 1024, 2048, 4096,
8192, 16384, 32768.rw Integer32 .3.1.1.5 |
atmVpPmRowStatusCreation/Deletion of rows in the table.rw RowStatus (SNMPv2-TC) .3.1.1.6 |
atmVpPmSinkoff (1) - Deactivate PM.
fwd (2) - Activate Forward PM only.
fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.rw Enumeration .3.1.1.7 |
atmVpPmSourceoff (1) - Deactivate PM.
fwd (2) - Activate Forward PM only.
fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.rw Enumeration .3.1.1.8 |
atmVcPmTableThis table contains parameters for VC performance monitoring. SEQUENCE OF AtmVcPmEntry .3.2 |
atmVcPmEntryAn entry in table. AtmVcPmEntry .3.2.1 |
atmVcPmIfIndexThe interface index of the ATM layer.ro Integer32 .3.2.1.1 |
atmVcPmVpiThe VPI of the Performance Monitoring VCL.ro Integer32 .3.2.1.2 |
atmVcPmVciThe VCI of the PM VCL.ro Integer32 .3.2.1.3 |
atmVcPmAdminStatusup(2) - Activate PM.
down(3) - Deactivate PM.
listenToActivationCells(4) - .
originateActivationCells(5) - .rw Enumeration .3.2.1.4 |
atmVcPmDirectionThe direction of PM.rw Enumeration .3.2.1.5 |
atmVcPmBlockSizeValid block sizes (in cells): 128, 256, 512, 1024, 2048, 4096,
8192, 16384, 32768.rw Integer32 .3.2.1.6 |
atmVcPmRowStatusCreation/Deletion of rows in the table.rw RowStatus (SNMPv2-TC) .3.2.1.7 |
atmVcPmSinkoff (1) - Deactivate PM.
fwd (2) - Activate Forward PM only.
fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.rw Enumeration .3.2.1.8 |
atmVcPmSourceoff (1) - Deactivate PM.
fwd (2) - Activate Forward PM only.
fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.rw Enumeration .3.2.1.9 |
atmNteConfVcTableThe ATM VC configuration table.
The table is an extension to the atmVclTable of
RFC-2515. SEQUENCE OF AtmNteConfVcEntry .4 |
atmAceRedundancyTrapThe trap is sent upon change in link as a result of redundancy.
The ifIndex parameter indicates the current active link. NOTIFICATION-TYPE .4 |
atmNteConfVcEntryAn entry in the ATM VC configuration table.
ifIndex of the ATM layer. AtmNteConfVcEntry .4.1 |
atmConfVcPolicingPolicing method desired for this VCL.rw Enumeration .4.1.1 |
atmConfVcCCAdminStatusup(2) - Activate Continuity Check (CC).
down(3) - Deactivate CC.
source(4) - Activate OAM CC(Continuity Check) of local agent
( start sending Oam cells to the remote side ).
sink(5) - Activate CC of remote agent ( start receiving Oam cells from
remote side).
listenToActivationCells (6) - Passive listener till gets an activation request
originateActivationCells(7) - Sands Activation cell according to atmConfVcCCDirection.rw Enumeration .4.1.2 |
atmConfVcLoopbackAdminStatusup(2) - Start loopback OAM cells.
down(3) - Stop sending loopback OAM cells.
For ace2002:
up(2) - Transmitting LB cells with llid all ones
(i.e. FFFF..FF)
down(3) - Not transmitting LB cells.
llid(4) - Transmitting LB cells with llid indicated
in the address field.
segment(5) - Transmitting Segment LB cells with llid
all ones.
endToEnd(6) - Transmitting End to End LB cells with llid
all ones.
segmentLlid(7) - Transmitting Segment LB cells with
llid indicated in the address field.
endToEndLlid(8) - Transmitting LB cells with llid
indicated in the address field.
This parameter value might be in conflict with
atmConfVcOamSupport value, since this parameter is for LB,
while atmConfVcOamSupport is for any other OAM cells.rw Enumeration .4.1.3 |
atmConfVcLoopbackSinkAddressDestination address.
For ace101: 2 bytes are used.
For ace2002: 16 bytes are used.rw OCTET STRING .4.1.4 |
atmConfVcCongestionControlEach bit indicates a selection of one option
as the following description. All combinations
are possible and legal.
The codes are:
1 - EPD
2 - CLP
4 - EFCI.
For ace2002:
1 - Packet Discard.rw OCTET STRING .4.1.5 |
atmConfVcCCDirectionboth(2) - Agent sends OAM CC cells and checks received OAM CC cells.
none(3) - Agent does not send and does not check received OAM CC cells.
source(4)- Agent sends OAM CC cells.
sink(5) - Agent checks received OAM CC cells.rw Enumeration .4.1.6 |
atmConfVcCreationTimeA date-time in which the VC was created.ro DateAndTime (SNMPv2-TC) .4.1.7 |
atmConfVcOamSupportOAM support mode, which determines the device location
in a segment wise.
endToEndAndSegment - In this mode the OAM cells are generated
before the ABM (ATM Buffer Manager), so
that the PCR and CDVT will not be affected.rw Enumeration .4.1.8 |
atmConfVcCCActivationCtrlmanual(1) - CC Activation process is disable
activator(2) - ACE-101 initiate CC Activation process
listener(3) - ACE-101 wait to CC Activation request from remote side.rw Enumeration .4.1.9 |
atmConfVcCCOperStatusinitial (1) - The CC activation process is not started.
up (2) - Continuity Check (CC) activated.
down (3) - CC deactivated.
source (4) - OAM CC(Continuity Check) of local agent activated.
sink (5) - OAM CC of remote agent activated.
both (8) - OAM CC of local and remote agents activation.
timeout (9) - Timeout occured on receiving answer from
the remote agent.
denied (10) - CC activation process rejected by remote agent.
conflict (11) - local and remote sides requested activation
simultaneously.
manual (12) - OAM CC of local agent activated manually.ro Enumeration .4.1.10 |
atmConfVcLoopbackTrafficThis parameter has both command and status meanings:
off(2) - Set to 'Off' will Stop traffic loop. Getting this
value means that the loop is not running.
on (3) - Set to 'On' will start traffic loop. Getting
this value means that the loop is currently running.rw Enumeration .4.1.11 |
atmConfVcLoopbackFailureIndThis object allows user to define the Indication that will be created upon
a LB cell failure.
disabled(2) - no indication will be created.
segmentAis(3) - will cause Tx of a segment AIS.
segmentRdi(4) - will cause Tx of a segment RDI.
segmentAisAndRdi(5) - will cause Tx of a segment AIS & RDI.
endToEndAis(6) - will cause Tx of an End to End AIS.
endToEndRdi(7) - will cause Tx of an End to End RDI.
endToEndAisAndRdi(8) - will cause Tx of an End to End AIS & RDI.
Default: disabled(2).rw Enumeration .4.1.12 |
atmConfVcLoopbackFailureThresholdThe number of the LB failures before starting transmission of the
Indication defined by atmConfVcLoopbackFailureInd.
Range: 1..16. Default: 1.rw Integer32 .4.1.13 |
atmConfVcOamDirectionThe direction of OAM cell insertion.
downStream(2) - The OAM cell will be inserted in downStream.
upStream(3) - The OAM cell will be inserted in upStream.rw Enumeration .4.1.14 |
atmConfVcNameVC Name.rw DisplayString (SNMPv2-TC) .4.1.15 |
atmConfVcConnectedThis object indicates whether this VC is connected
and if connected, what is it connected to.ro Enumeration .4.1.16 |
atmConfVcOamDescrIndexThis parameter indicates the VCL's OAM Descriptor index,
according to the OAM Descriptor Configuration Table.rw Integer32 .4.1.17 |