ATM-X-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for ATM-X-MIB.
161
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
161 total| Object Name |
|---|
wanGen OBJECT IDENTIFIER .1.3.6.1.4.1.164.3.1 |
diverseIfWanGen OBJECT IDENTIFIER .1.3.6.1.4.1.164.3.1.6 |
adslIf OBJECT IDENTIFIER .1.3.6.1.4.1.164.3.1.6.10 |
adslConfTableA list of ADSL Configuration entries SEQUENCE OF AdslConfEntry .1.3.6.1.4.1.164.3.1.6.10.1 |
adslConfEntryAn entry in adslConfTable AdslConfEntry .1.3.6.1.4.1.164.3.1.6.10.1.1 |
adslConfCnfgIdxThis object indicates the Idx of the Config being accessed.
Idx of 255 relates to the Temporary (Scratch) Config.
For products that support several configurations,
Set can be performed only to the Temporary Config (=255).ro Integer32 .1.3.6.1.4.1.164.3.1.6.10.1.1.1 |
adslConfFramingTypeADSL Frame typerw Enumeration .1.3.6.1.4.1.164.3.1.6.10.1.1.2 |
adslConfPilotToneRequestThis parameter controls Pilot Tone Request (PTR).rw Enumeration .1.3.6.1.4.1.164.3.1.6.10.1.1.3 |
adslConfTrellisCodingThis parameter enables/disables Trellis error detection code.
using error detection code may introduce delays.rw Enumeration .1.3.6.1.4.1.164.3.1.6.10.1.1.4 |
adslConfTransmissionModeThis parameter controls transmision mode:
Echo Cancellation is required when both ATU-C an ATU-R use
the same frequency.
Frequency Division (different frequency ranges for ATU-C
and ATU-R) may limit data rate.rw Enumeration .1.3.6.1.4.1.164.3.1.6.10.1.1.5 |
adslConfStandardComplianceThis parameter indicates standard compliance
G.Lite enables extended ADSL range, ease of installation,
but requires lower rate.rw Enumeration .1.3.6.1.4.1.164.3.1.6.10.1.1.6 |
adslConfMaxBitPerBinThis parameter indicates maximum number of bits per ADSL Bin.
Each Bin has bandwidth of 4khz.
Range of values for this parameter is 0..15rw Integer32 .1.3.6.1.4.1.164.3.1.6.10.1.1.7 |
adslConfTxStartFreqBinThis parameter controls Transmit Start Bin number.
For ADSL Annex A - range of values is 6 to 31.
For ADSL Annex B - range of values is 33 to 63.
Frequency (in khz unit) is calculated by multiplying this
parameter value by bin bandwidth (4Khz)rw Integer32 .1.3.6.1.4.1.164.3.1.6.10.1.1.8 |
adslConfTxEndFreqBinThis parameter controls Transmit End Bin number.
For ADSL Annex A - range of values is 6 to 31.
For ADSL Annex B - range of values is 33 to 63.
requency (in khz unit) is calculated by multiplying this
value by bin bandwidth (4Khz)rw Integer32 .1.3.6.1.4.1.164.3.1.6.10.1.1.9 |
adslConfRxStartFreqBinThis parameter controls Receive Start Bin number.
Range of values for this parameter depends on ADSL Annex supported,
and transmisson mode (adslTransmissionMode) selected:
ADSL Annex A and Echo Cancellation (EC) : 6 to 255
ADSL Annex A and Frequency Division (FDM) : 32 to 255
ADSL Annex B and Echo Cancellation (EC) : 33 to 255
ADSL Annex B and Frequency Division (FDM) : 64 to 255
Frequency (in khz unit) is calculated by multiplying this
value by bin bandwidth (4Khz)rw Integer32 .1.3.6.1.4.1.164.3.1.6.10.1.1.10 |
adslConfRxEndFreqBinThis parameter controls Receive End Bin number.
Range of values for this parameter depends on ADSL Annex supported,
and transmisson mode (adslTransmissionMode) selected:
ADSL Annex A and Echo Cancellation (EC) : 6 to 255
ADSL Annex A and Frequency Division (FDM) : 32 to 255
ADSL Annex B and Echo Cancellation (EC) : 33 to 255
ADSL Annex B and Frequency Division (FDM) : 64 to 255
Frequency (in khz unit) is calculated by multiplying this
value by bin bandwidth (4Khz)rw Integer32 .1.3.6.1.4.1.164.3.1.6.10.1.1.11 |
adslConfTxPowerAttenuationThis parameter controls Transmit Gain in dB units
Range is 0 to 12dB. Resolution is 1 dBrw Integer32 .1.3.6.1.4.1.164.3.1.6.10.1.1.12 |
adslStatusTableA list of Adsl Status entries SEQUENCE OF AdslStatusEntry .1.3.6.1.4.1.164.3.1.6.10.2 |
adslStatusEntryAn entry in adslStatusTable AdslStatusEntry .1.3.6.1.4.1.164.3.1.6.10.2.1 |
adslStatusBitRxRateThis parameter indicates actual Receive (Downstream)
rate on this channel
Range of values for this parameter is 0 -8,064,000 bpsro Gauge32 UNITS "bps" .1.3.6.1.4.1.164.3.1.6.10.2.1.1 |
sdslIf OBJECT IDENTIFIER .1.3.6.1.4.1.164.3.1.6.11 |
sdslConfTableA list of SDSL Configuration entries SEQUENCE OF SdslConfEntry .1.3.6.1.4.1.164.3.1.6.11.1 |
sdslConfEntryAn entry in sdslConfTable SdslConfEntry .1.3.6.1.4.1.164.3.1.6.11.1.1 |
sdslConfCnfgIdxThis object indicates the Idx of the Config being accessed.
Idx of 255 relates to the Temporary (Scratch) Config.
For products that support several configurations, Set can be performed
only to the Temporary Config (=255).ro Integer32 .1.3.6.1.4.1.164.3.1.6.11.1.1.1 |
sdslConfRateAquisitionSDSL Rate Aquisition mode
Default value = fixed.rw Enumeration .1.3.6.1.4.1.164.3.1.6.11.1.1.2 |
sdslConfBaudRateSDSL baud rate. Not applicable if rate aquisition is AutoNegotiation.
Default value = r144kbpsrw Enumeration .1.3.6.1.4.1.164.3.1.6.11.1.1.3 |
sdslConfModeSDSL mode - COE (HTU-C) or CPE (HTU-R)
Default value = COErw Enumeration .1.3.6.1.4.1.164.3.1.6.11.1.1.4 |
shdslIf OBJECT IDENTIFIER .1.3.6.1.4.1.164.3.1.6.12 |
radHdsl2ShdslEvents OBJECT IDENTIFIER .1.3.6.1.4.1.164.3.1.6.12.0 |
radHdsl2ShdslLoopBackTrapThis notification indicates that a remote loopback
has been activated on the Embedded Operations Channel (EOC) of the SHDSL
link. NOTIFICATION-TYPE .1.3.6.1.4.1.164.3.1.6.12.0.1 |
shdslEndpointCurrTableThis table is an extension of hdsl2ShdslEndpointCurrTable of rfc3276
It contains current status and performance information
for segment endpoints in HDSL2/SHDSL Lines. As with other
tables in this MIB indexed by ifIndex, entries in this table
MUST be maintained in a persistent manner. SEQUENCE OF ShdslEndpointCurrEntry .1.3.6.1.4.1.164.3.1.6.12.1 |
shdslEndpointCurrEntryAn entry in the shdslEndpointCurrTable. Each entry
contains status and performance information relating to a
single segment endpoint. It is indexed by the ifIndex of the
HDSL2/SHDSL line, the UnitId of the associated unit, the side
of the unit, and the wire-pair of the associated modem. ShdslEndpointCurrEntry .1.3.6.1.4.1.164.3.1.6.12.1.1 |
hdsl2ShdslEndpointCurrRcvGainThe current receive gain in hundredth of dB.ro Integer32 UNITS "dB" .1.3.6.1.4.1.164.3.1.6.12.1.1.1 |
hdsl2ShdslEndpointCurrTransPowerThe current transmit power in tenth of dBm.ro Integer32 .1.3.6.1.4.1.164.3.1.6.12.1.1.2 |
hdsl2ShdslEndpointCurrPowerBOThe current transceiver actual power packoff from 0dB to 6dB.ro Integer32 UNITS "dB" .1.3.6.1.4.1.164.3.1.6.12.1.1.3 |
hdsl2ShdslEndpointCurrLineStatusThe current line synchronization status.ro Enumeration .1.3.6.1.4.1.164.3.1.6.12.1.1.4 |
hdsl2ShdslEndpointCurrOpStateThe current operational state.ro Bits .1.3.6.1.4.1.164.3.1.6.12.1.1.5 |
hdsl2ShdslEndpointAccumulatedTimeElapsedThe time (in hundredths of a second) since the
accumulated counters were last re-initialized:
Accumulated counters are hdsl2ShdslEndpointES,
hdsl2ShdslEndpointSES, hdsl2ShdslEndpointCRCanomalies
hdsl2ShdslEndpointLOSWS, and hdsl2ShdslEndpointUAS.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.164.3.1.6.12.1.1.6 |
hdsl2ShdslEndpointCurrPsdThis object indicates use of symmetric/asymmetric PSD (Power
Spectral Density) Mask for the associated SHDSL Line.ro Enumeration .1.3.6.1.4.1.164.3.1.6.12.1.1.7 |
shdslEndpointMaintTableThis table supports maintenance operations (eg. loopbacks)
to be performed on HDSL2/SHDSL segment endpoints. This table
contains live data from equipment. As such, it is NOT
persistent. SEQUENCE OF ShdslEndpointMaintEntry .1.3.6.1.4.1.164.3.1.6.12.2 |
shdslEndpointMaintEntryAn entry in the hdsl2ShdslEndpointMaintTable. Each entry
corresponds to a single segment endpoint, and is indexed by the
ifIndex of the HDSL2/SHDSL line, the UnitId of the associated
unit and the side of the unit. ShdslEndpointMaintEntry .1.3.6.1.4.1.164.3.1.6.12.2.1 |
shdslMaintPowerBackOffThis object configures the receiver at the associated
segment endpoint to operate in default or enhanced power
backoff mode.
powerbackoff may also be disabledrw Enumeration .1.3.6.1.4.1.164.3.1.6.12.2.1.1 |
shdslSpanConfProfileTableThis table supports definitions of span configuration
profiles for SHDSL lines. HDSL2 does not support these
configuration options. This table MUST be maintained
in a persistent manner. SEQUENCE OF ShdslSpanConfProfileEntry .1.3.6.1.4.1.164.3.1.6.12.3 |
shdslSpanConfProfileEntryEach entry corresponds to a single span configuration
profile. Each profile contains a set of span configuration
parameters. The configuration parameters in a profile are
applied to those lines referencing that profile (see the
hdsl2ShdslSpanConfProfile object). Profiles may be
created/deleted using the row creation/deletion mechanism
via hdsl2ShdslSpanConfProfileRowStatus. If an active
entry is referenced in hdsl2ShdslSpanConfProfile, the
entry MUST remain active until all references are removed. ShdslSpanConfProfileEntry .1.3.6.1.4.1.164.3.1.6.12.3.1 |
hdsl2ShdslSpanConfEocCompatibleThis object indicate if device supports only
standard EOC messages or also proprietary messages.ro Enumeration .1.3.6.1.4.1.164.3.1.6.12.3.1.1 |
hdsl2ShdslSpanConfAsymmetricPSDRateThis object indicates line rate when
rfc3276.hdsl2ShdslSpanConfPSD value is asymmetric(2).
Seleceted rate depends on transmission mode -
specified in Annex A or B of G.991.2.
For Annex A;
R1 selects the 776 or 784 kbit/s
R2 selects the 1544 or 1552 kbit/s
For Annex B ;
R1 selects the 2312 kbit/s
R2 selects the 2056 kbit/srw Enumeration .1.3.6.1.4.1.164.3.1.6.12.3.1.2 |
hdsl2ShdslIfConf OBJECT IDENTIFIER .1.3.6.1.4.1.164.3.1.6.12.4 |
hdsl2ShdslIfConfTableThis table enables configuration of HDSL2/SHDSL interfaces
per configuration index.
Write operation for products supporting Active+Temp configurations,
is possible only on the Temp configuration(255). SEQUENCE OF Hdsl2ShdslIfConfEntry .1.3.6.1.4.1.164.3.1.6.12.4.1 |
hdsl2ShdslIfConfEntryAn entry in the hdsl2ShdslIfConfTable. Hdsl2ShdslIfConfEntry .1.3.6.1.4.1.164.3.1.6.12.4.1.1 |
hdsl2ShdslIfConfIdxThis object indicates the Idx of the Config being accessed.
Idx of 255 relates to the Temporary (Scratch) Config.
Write operation for products supporting Active+Temp configurations,
is allowed to Temporary configuration only.ro Integer32 .1.3.6.1.4.1.164.3.1.6.12.4.1.1.1 |
hdsl2ShdslSideIdxThis object indicates the Side of the managed object: Near-End
or Far-End.ro Enumeration .1.3.6.1.4.1.164.3.1.6.12.4.1.1.2 |
hdsl2ShdslMaxBwMaximum BW (Bandwidth) of the Shdsl Line, in Kbps units.
Respective Max No. of TSs = Max. Rate/64
This object can be Set only for a Central (xtuC) unit.rw Enumeration .1.3.6.1.4.1.164.3.1.6.12.4.1.1.3 |
hdsl2ShdslPwrBackoffThis object configures the receiver at the associated
segment endpoint to enable/disable power backoff mode.
This object is similar to hdsl2ShdslMaintPowerBackOff, but per
configuration. Therefore, the order of the enum values is the same.rw Enumeration .1.3.6.1.4.1.164.3.1.6.12.4.1.1.4 |
hdsl2ShdslTxModeThis object configures the Transmission Mode for the SHDSL Line.
This object can be Set only for a Central (xtuC) unit.rw Enumeration .1.3.6.1.4.1.164.3.1.6.12.4.1.1.5 |
hdsl2ShdslAttenuationThresholdThis object configures the Attentuation alarm threshold.
0=Off
Valid values: 0..127 .rw Integer32 UNITS "dB" .1.3.6.1.4.1.164.3.1.6.12.4.1.1.6 |
hdsl2ShdslSnrMarginThresholdThis object configures the SNR margin alarm threshold.
0=Off
Valid values: 0..15 .rw Integer32 UNITS "dB" .1.3.6.1.4.1.164.3.1.6.12.4.1.1.7 |
hdsl2ShdslTs0OverDslThis object configures the way TS0 will be treated over the SHDSL Line.
looped - looped inside
transparent - sent transparently over the DSL Line.
This object can be Set only for a Central (xtuC) unit.rw Enumeration .1.3.6.1.4.1.164.3.1.6.12.4.1.1.8 |
hdsl2ShdslModeThis object is relevant only for the Near-End device.
stuC - Central
stuR - Remote .rw Enumeration .1.3.6.1.4.1.164.3.1.6.12.4.1.1.9 |
hdsl2ShdslTsCompactionModeThis object configures how TSs will be compacted over the SHDSL Line.
In both mapping cases (2),(3), only the TSs connected on the E1 line will be
transferred over the SHDSL Line
noCompaction - the whole E1 BW is reserved on the SHDSL Line,
even if only part of the TSs are actually connected.
noMapping - there is no mapping between the E1 TSs and the SHDSL frame TSs.
Therefore, E1 connected TSs are ordered in ascending order (e.g
E1 TSs 2, 16, 20 will occupy places 1, 2, 3 in SHDSL Line).
In this case, if user wants to add connection for
a TS that is lower than the existing ones on SHDSL,
the TSs that are higher will have to move.
That causes breaks in service for the moved TSs.
(e.g if E1 TS8 is added in the above case,
TSs 16 and 20 will move, so that by the
end of this process, the E1 TSs 2, 8, 16, 20 will
be ordered in SHDSL frame as 1, 2, 3, 4).
withMapping - there is a mapping between the E1 TSs and the SHDSL frame TSs.
Therefore, if some TSs were connected and then user wants to add
additional E1 TSs, there is no need to move the existing TSs of the
SHDSL frame. The additional TSs will be added AFTER the existing ones,
or in gaps created by E1 TSs removed by user. The main thing is that
the existing TSs will NOT be moved and so, their service will not be
damaged by the addition or removal of E1 TS connections.
lowTsMapping - the first 2 TSs are used for Signaling (TS16) and Dedicated TS
if relevant. The payload starts afterwards, unmapped (according to
E1 connected TSs order). This will ensure that Signaling and
Dedicated TS will continue to function also when new TSs are
connected. User will still get service breaks when TSs are moved.
spareMapping - applicable only for MP-2100/2104 cards. It should be selected only
when working vs. a MP-2100.2104. It resembles the noMapping option,
but it contains Spare TSs for unconnected TSs. These Spare TSs
will prevent service breaks upon added connections, because these
will be selected from the Spare existing TSs.rw Enumeration .1.3.6.1.4.1.164.3.1.6.12.4.1.1.10 |
voiceIf OBJECT IDENTIFIER .1.3.6.1.4.1.164.3.1.6.13 |
voiceIfCadenceCnfgTableVoice port ringing cadence configuration table.
Each ringing cycle, indexed by voiceIfCadenceIdx,
consists of a number of ring ON-Period/ring OFF-Period
pairs. Pairs are indexed sequentially, according to
voiceIfCadencePeriodIdx: 1,2,...number of pairs SEQUENCE OF VoiceIfCadenceCnfgEntry .1.3.6.1.4.1.164.3.1.6.13.1 |
voiceIfCadenceCnfgEntryRinging cadence configuration per voice port. VoiceIfCadenceCnfgEntry .1.3.6.1.4.1.164.3.1.6.13.1.1 |
voiceIfCadenceCnfgIdxThis object indicates the Idx of the
Agent Cnfg the following objects refer to.
255=Temporary Cnfg (when relevant,
Set is done only to this configuration).
For Agents that support only one configuration,
this object will be constant=1. Integer32 .1.3.6.1.4.1.164.3.1.6.13.1.1.1 |
voiceIfCadencePortIdxVoice Port Index. May equal to the value of ifIndex. Integer32 .1.3.6.1.4.1.164.3.1.6.13.1.1.2 |
voiceIfCadenceIdxCadence (ringing type) index. Integer32 .1.3.6.1.4.1.164.3.1.6.13.1.1.3 |
voiceIfCadencePeriodIdxPeriods index (pair number) in a ringing cycle Cadence.
This index must be sequential, start from 1. Its maximum
value is the number of pairs of certain ringing type.
For Vmux-110, one or two period pairs may be defined. Integer32 .1.3.6.1.4.1.164.3.1.6.13.1.1.4 |
voiceIfCadenceRowStatusThis attribute allows to create/delete
ringing cadence entry in this table.
For Vmux-110, only a single cadance can be defined.
Delete action of a period entry can be performed only
if it is the last existing period of the cadance.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.164.3.1.6.13.1.1.5 |
voiceIfCadenceRingOnPeriodDuration (in tenth of seconds) of Ringing (ON)
period.rw Integer32 .1.3.6.1.4.1.164.3.1.6.13.1.1.6 |
voiceIfCadenceRingOffPeriodDuration (in tenth of seconds) of Silence (OFF)
period.rw Integer32 .1.3.6.1.4.1.164.3.1.6.13.1.1.7 |
voiceIfCnfgTableVoice port configuration table. SEQUENCE OF VoiceIfCnfgEntry .1.3.6.1.4.1.164.3.1.6.13.2 |
voiceIfCnfgEntryConfiguration per voice port. VoiceIfCnfgEntry .1.3.6.1.4.1.164.3.1.6.13.2.1 |
voiceIfCnfgIdxThis object indicates the Idx of the
Agent Cnfg the following objects refer to.
255=Temporary Cnfg (when relevant,
Set is done only to this configuration).
For Agents that support only one configuration,
this object will be constant=1. Integer32 .1.3.6.1.4.1.164.3.1.6.13.2.1.1 |
voiceIfPortIdxIndex of voice port . Integer32 .1.3.6.1.4.1.164.3.1.6.13.2.1.2 |
voiceIfRingingTimeoutRinging timeout in seconds.rw Integer32 .1.3.6.1.4.1.164.3.1.6.13.2.1.3 |
voiceIfFlashTimeoutA time period in milliseconds. Flash (Register Recall)
is detected if On-Hook time is shorter than this timeout.rw Integer32 .1.3.6.1.4.1.164.3.1.6.13.2.1.4 |
voiceIfRxGainReceive gain in dB.rw Integer32 .1.3.6.1.4.1.164.3.1.6.13.2.1.5 |
voiceIfTxGainTransmission gain in dB.rw Integer32 .1.3.6.1.4.1.164.3.1.6.13.2.1.6 |
voiceIfSignalingABCDOctet String.
Nibble No. 1 represents ON Hook (same for Rx and Tx).
Nibble No. 2 represents OFF Hook (same for Rx and Tx).
Nibble No. 3 represents Reverse Polarity.
Nibble No. 4 represents Ring pattern 1.
Nibble No. 5 represents Ring pattern 2.
Nibble No. 6 is not used.
The bits will be as following:
Bit 1 = Bit A - ON Hook (LSB)
Bit 2 = Bit B - ON Hook
Bit 3 = Bit C - ON Hook
Bit 4 = Bit D - ON Hook
Bit 5 = Bit A - OFF Hook
Bit 6 = Bit B - OFF Hook
Bit 7 = Bit C - OFF Hook
Bit 8 = Bit D - OFF Hook
Bit 9 = Bit A - Reverse Polarity
Bit 10 = Bit B - Reverse Polarity
Bit 11 = Bit C - Reverse Polarity
Bit 12 = Bit D - Reverse Polarity
Bit 13 = Bit A - Ring 1
Bit 14 = Bit B - Ring 1
Bit 15 = Bit C - Ring 1
Bit 16 = Bit D - Ring 1
Bit 17 = Bit A - Ring 2
Bit 18 = Bit B - Ring 2
Bit 19 = Bit C - Ring 2
Bit 20 = Bit D - Ring 2
Bits 21...24 = 0 (not used). (Bit 24 is MSB).
For Vmux-110:
Ring 1 and Ring 2 are used. The default is 3 octets.
(MSB) 0000 1011 1011 1001 1011 1010 (LSB)rw OCTET STRING .1.3.6.1.4.1.164.3.1.6.13.2.1.7 |
voiceIfStateAttribute indicating voice port state.ro Enumeration .1.3.6.1.4.1.164.3.1.6.13.2.1.8 |
voiceIfCallStateAttribute indicating the status of the call on this port.
In Vmux devices this attribute is used for FXS ports.ro Enumeration .1.3.6.1.4.1.164.3.1.6.13.2.1.9 |
services OBJECT IDENTIFIER .1.3.6.1.4.1.164.6.3 |
wfq OBJECT IDENTIFIER .1.3.6.1.4.1.164.6.3.1 |
wfqTableThis table allows user to define several
WFQ tables per output port.
WFQ supports flows with different bandwidth requirements
by giving each queue a weight that assigns it
a different percentage of output port bandwidth.
When Weighted Fair Queuing is used,
it is possible to precisely attribute bandwidth
partitioning among the queues.
When there is congestion, each class (queue)
is not allowed to use more bandwidth than the amount
allocated to it. SEQUENCE OF WfqEntry .1.3.6.1.4.1.164.6.3.1.1 |
wfqEntryAn entry in the Weighted Fair Queueing table. WfqEntry .1.3.6.1.4.1.164.6.3.1.1.1 |
wfqCnfgIdxThis object indicates the Idx of the Agent Cnfg the following
objects refer.
255=Temporary Cnfg (when relevant,
Set is done only to this configuration).
For Agents that support only one configuration,
this object will be constant=1. Integer32 .1.3.6.1.4.1.164.6.3.1.1.1.1 |
wfqPrtIdxThis object indicates a unique port or interface number,
for which Weighted Fair Queueing table is applicable .
For numbering, see product's spec.
For some products, the numbering can equal ifIndex.
Value of 255 (not applicable) refer to system level queue Integer32 .1.3.6.1.4.1.164.6.3.1.1.1.2 |
wfqTblIdxThis object indicates which Weighted Fair Queueing (WFQ)
Table is being used. There can be several tables.
For FCD-155 User will select which one will be used
for a virtual concatenation group.Valid values are 1,2 Integer32 .1.3.6.1.4.1.164.6.3.1.1.1.3 |
wfqQueueIdxThis object indicates a queue index.
For FCD-155, valid queues are 1..3.
The 4th queue is not in MIB.
Its weight will be RO, Calculated according to
the sum of the 3 first queues. Integer32 .1.3.6.1.4.1.164.6.3.1.1.1.4 |
wfqRowStatusThis object enables Creation/Deletion of
rows in the WFQ table.
For FCD-155, rows are not created nor destroyed by user.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.164.6.3.1.1.1.5 |
wfqWeightValueThis object indicates a relative weight value.
User should make sure that the sum of
values for all queues will not exceed 100%
(sum should be BELOW 100% in order
to leave some BW percentage for last queue)rw Integer32 .1.3.6.1.4.1.164.6.3.1.1.1.6 |
dscpMapping OBJECT IDENTIFIER .1.3.6.1.4.1.164.6.3.2 |
dscpMappingTableMapping of DSCP value to a regenerated priority level. SEQUENCE OF DscpMappingEntry .1.3.6.1.4.1.164.6.3.2.1 |
dscpMappingEntryAn entry in dscpMappingTable. DscpMappingEntry .1.3.6.1.4.1.164.6.3.2.1.1 |
dscpMappingCnfgIdxThis object indicates the Idx of the Agent Cnfg the following
objects refer to.
255=Temporary Cnfg (when relevant, Set is done only
to this configuration).
For Agents that support only one configuration,
this object will be constant=1.
This object can be used to carry additional indexing
(e.g port index) when needed. Integer32 .1.3.6.1.4.1.164.6.3.2.1.1.1 |
dscpMappingDscpIdxDSCP value of the incoming IP packet Dscp .1.3.6.1.4.1.164.6.3.2.1.1.2 |
dscpMappingRegenPriorityThe Regenerated Priority level the
incoming DSCP value is mapped to.
For FCD-155, valid values are 0,1,2,3rw Integer32 .1.3.6.1.4.1.164.6.3.2.1.1.3 |
ifTeQos OBJECT IDENTIFIER .1.3.6.1.4.1.164.6.3.3 |
ifTeQosTableThe TE QOS Interface Table. SEQUENCE OF IfTeQosEntry .1.3.6.1.4.1.164.6.3.3.1 |
ifTeQosEntryAn entry in the TE QOS Interface table. IfTeQosEntry .1.3.6.1.4.1.164.6.3.3.1.1 |
ifTeQosIdx1This object indicates the 1st Index of the table. Integer32 .1.3.6.1.4.1.164.6.3.3.1.1.1 |
ifTeQosIdx2This object indicates the 2nd Index of the table. Integer32 .1.3.6.1.4.1.164.6.3.3.1.1.2 |
ifTeQosIdx3This object indicates the 3rd Index of the table. Integer32 .1.3.6.1.4.1.164.6.3.3.1.1.3 |
ifTeQosParamThis object is used for QOS attributes
of the entry's entities.rw OCTET STRING .1.3.6.1.4.1.164.6.3.3.1.1.4 |
atmGen OBJECT IDENTIFIER .radAtm.2 |
IMPORTS NOTIFICATION-TYPE .radAtm.2 |
atmPerfHistory OBJECT IDENTIFIER .radAtm.2.1 |
atmIfPerformance OBJECT IDENTIFIER .radAtm.2.1.1 |
aal5VccXTableThis table is an extension to AAL5 VCC Table. SEQUENCE OF Aal5VccXEntry .radAtm.2.1.1.4 |
aal5VccXEntryThis list contains the additional AAL5 VCC
performance parameters and is indexed
by ifIndex values of AAL5 interfaces
and the associated VPI/VCI values. Aal5VccXEntry .radAtm.2.1.1.4.1 |
aal5VccInFramesThe number of frames received via this interface.ro Counter32 .radAtm.2.1.1.4.1.1 |
aal5VccOutFramesThe total number of frames transmitted out of the
interface.ro Counter32 .radAtm.2.1.1.4.1.2 |
aal5VccUnknownProtocolFramesThe number of frames that were discarded due to unsupported
protocol encapsulation on this VCC.ro Counter32 .radAtm.2.1.1.4.1.3 |
aal5VccCurrentTableThe AAL5 Current table. SEQUENCE OF Aal5VccCurrentEntry .radAtm.2.1.1.5 |
aal5VccCurrentEntryAn entry in the AAL5 Current table. Aal5VccCurrentEntry .radAtm.2.1.1.5.1 |
aal5VccCurrentInFramesThe counter associated with the number of received frames,
encountered by the AAL5 interface in the current 15 minute
interval.ro Gauge32 .radAtm.2.1.1.5.1.1 |
aal5VccCurrentOutFramesThe counter associated with the number of transmitted frames,
encountered by the AAL5 interface in the current 15 minute
interval.ro Gauge32 .radAtm.2.1.1.5.1.2 |
aal5VccCurrentUnknownProtocolFramesThe counter associated with the number of frames that were
discarded due to unsupported protocol encapsulation,
encountered by the AAL5 interface in the current 15 minute
interval.ro Gauge32 .radAtm.2.1.1.5.1.3 |
aal5VccCurrentCrcErrorsThe counter associated with the number of AAL5 CPCS PDUs
received with CRC-32 errors, encountered by the AAL5
interface in the current 15 minute interval.ro Gauge32 .radAtm.2.1.1.5.1.4 |
aal5VccCurrentLengthErrorThe counter associated with the number of received frames
with length error, encountered by the AAL5 interface in the
current 15 minute interval.ro Gauge32 .radAtm.2.1.1.5.1.5 |
aal5VccCurrentInputCongestionDroppedThe counter associated with the number of
dropped frames due to congestion, encountered by
the AAL5 interface on the Receive direction
in the current 15 minute interval.ro Gauge32 .radAtm.2.1.1.5.1.6 |
aal5VccCurrentOutputCongestionDroppedThe counter associated with the number of
dropped frames due to congestion, encountered by
the AAL5 interface on the Transmit direction
in the current 15 minute interval.ro Gauge32 .radAtm.2.1.1.5.1.7 |
aal5VccIntervalTableThe AAL5 Interval table. SEQUENCE OF Aal5VccIntervalEntry .radAtm.2.1.1.6 |
aal5VccIntervalEntryAn entry in the AAL5 Interval table. Aal5VccIntervalEntry .radAtm.2.1.1.6.1 |
aal5VccIntervalNumberA number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes interval
(assuming that all 96 intervals exist).ro Integer32 .radAtm.2.1.1.6.1.1 |
aal5VccIntervalInFramesThe counter associated with the number of received frames,
encountered by the AAL5 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge32 .radAtm.2.1.1.6.1.2 |
aal5VccIntervalOutFramesThe counter associated with the number of transmitted frames,
encountered by the AAL5 interface in in one of the previous
96, individual 15 minute, intervals.ro Gauge32 .radAtm.2.1.1.6.1.3 |
aal5VccIntervalUnknownProtocolFramesThe counter associated with the number of frames that were
discarded due to unsupported protocol encapsulation,
encountered by the AAL5 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge32 .radAtm.2.1.1.6.1.4 |
aal5VccIntervalCrcErrorsThe counter associated with the number of AAL5 CPCS PDUs
received with CRC-32 errors, encountered by the AAL5
interface in one of the previous 96, individual 15 minute,
intervals.ro Gauge32 .radAtm.2.1.1.6.1.5 |
aal5VccIntervalLengthErrorThe counter associated with the number of received frames
with length error, encountered by the AAL5 interface in one
of the previous 96, individual 15 minute, intervals.ro Gauge32 .radAtm.2.1.1.6.1.6 |
aal5VccIntervalInputCongestionDroppedThe counter associated with the number of dropped frames
due to a congestion, encountered by the AAL5 interface on
the Receive direction in one of the previous 96, individual
15 minute, intervalsro Gauge32 .radAtm.2.1.1.6.1.7 |
aal5VccIntervalOutputCongestionDroppedThe counter associated with the number of dropped frames
due to a congestion, encountered by the AAL5 interface on
the Transmit direction in one of the previous 96, individual
15 minute, intervalsro Gauge32 .radAtm.2.1.1.6.1.8 |
atmCes OBJECT IDENTIFIER .radAtm.9 |
atmCesPerformance OBJECT IDENTIFIER .radAtm.9.1 |
atmCesAal1CurrentTableThe AAL1 Current table. SEQUENCE OF AtmCesAal1CurrentEntry .radAtm.9.1.1 |
atmCesAal1CurrentEntryAn entry in the AAL1 Current table. AtmCesAal1CurrentEntry .radAtm.9.1.1.1 |
atmCesAal1CurrentIfIndexThe index of the AAL1 interface.
It may be ifIndex.ro Integer32 .radAtm.9.1.1.1.1 |
atmCesAal1CurrentSeqErrorsThe counter associated with the number of Discarded
cells due to wrong sequence number, encountered
by an AAL1 interface in the current 15 minute interval.ro Gauge32 .radAtm.9.1.1.1.2 |
atmCesAal1CurrentHdrErrorsThe counter associated with the number of Discarded
cells due to bad AAL1 header error (including correctable
and uncorrectable CRC, and bad parity), encountered
by an AAL1 interface in the current 15 minute interval.ro Gauge32 .radAtm.9.1.1.1.3 |
atmCesAal1CurrentPointerReframesThe counter associated with the number of events in
which a SDT pointer isn't where it is expected to be,
and must be reacquired, encountered by an AAL1 interface
in the current 15 minute interval.ro Gauge32 .radAtm.9.1.1.1.4 |
atmCesAal1CurrentBufUnderflowsThe counter associated with the number of buffer
underflow events, encountered by an AAL1 interface
in the current 15 minute interval.ro Gauge32 .radAtm.9.1.1.1.5 |
atmCesAal1CurrentBufOverflowsThe counter associated with the number of buffer
overflow events, encountered by an AAL1 interface
in the current 15 minute interval.ro Gauge32 .radAtm.9.1.1.1.6 |
atmCesAal1IntervalTableThe AAL1 Interval table. SEQUENCE OF AtmCesAal1IntervalEntry .radAtm.9.1.2 |
atmCesAal1IntervalEntryAn entry in the AAL1 Interval table. AtmCesAal1IntervalEntry .radAtm.9.1.2.1 |
atmCesAal1IntervalIfIndexThe index of the AAL1 interface.
It may be ifIndex.ro Integer32 .radAtm.9.1.2.1.1 |
atmCesAal1IntervalNumberA number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes interval
(assuming that all 96 intervals exist).ro Integer32 .radAtm.9.1.2.1.2 |
atmCesAal1IntervalSeqErrorsThe counter associated with the number of Discarded
cells due to wrong sequence number, encountered
by an AAL1 interface in one of the previous 96,
individual 15 minute, intervals.ro Gauge32 .radAtm.9.1.2.1.3 |
atmCesAal1IntervalHdrErrorsThe counter associated with the number of Discarded
cells due to bad AAL1 header error (including correctable
and uncorrectable CRC, plus bad parity), encountered
by an AAL1 interface in one of the previous 96,
individual 15 minute, intervals.ro Gauge32 .radAtm.9.1.2.1.4 |
atmCesAal1IntervalPointerReframesThe counter associated with the number of events in
which a SDT pointer isn't where it is expected to be,
and must be reacquired, encountered by an AAL1 interface
in one of the previous 96, individual 15 minute,
intervals.ro Gauge32 .radAtm.9.1.2.1.5 |
atmCesAal1IntervalBufUnderflowsThe counter associated with the number of buffer
underflow events, encountered by an AAL1 interface
in one of the previous 96, individual 15 minute,
intervals.ro Gauge32 .radAtm.9.1.2.1.6 |
atmCesAal1IntervalBufOverflowsThe counter associated with the number of buffer
overflow events, encountered by an AAL1 interface
in one of the previous 96, individual 15 minute,
intervals.ro Gauge32 .radAtm.9.1.2.1.7 |
atmCesConfiguration OBJECT IDENTIFIER .radAtm.9.2 |
atmCesXConfTableThis table is an extension of atmfCESConfTable table. SEQUENCE OF AtmCesXConfEntry .radAtm.9.2.1 |
atmCesXConfEntryConceptual row in atmfCESConfTable.
A new row is created in this table upon each new CES VCC creation. AtmCesXConfEntry .radAtm.9.2.1.1 |
atmCesXConfCBRModeThis parameter defines if to use Spaced or Normal CBR.
Normal - TD will be allocated from the policing range (described
in ACE2002 NMS SRS). The PCR is expanded with a constant
value of 30 cell/sec.
Spaced - TD will be allocated from the spacing range (described
in ACE2002 NMS SRS). The PCR and CDVT will be expanded
as described for Normal, and the CES traffic including
the OAM will be spaced out at the TD's PCR.
This mode is used to prevent CDVT violation due to OAM
cell insertion with the CES traffic.rw Enumeration .radAtm.9.2.1.1.1 |
radAtmRouter OBJECT IDENTIFIER .radAtm.10 |
atmIpoaLisIfMappingXTableThis table is an extension of a table
from RFC 2320: ipoaLisIfMappingTable -
The ATM Logical IP Subnet Interface Mapping Table. SEQUENCE OF AtmIpoaLisIfMappingXEntry .radAtm.10.1 |
atmIpoaLisIfMappingXEntryConceptual row in ipoaLisIfMappingTable. AtmIpoaLisIfMappingXEntry .radAtm.10.1.1 |
atmIpoaLisIfMappingTypeThis object indicates the Mapping Type.rw Enumeration .radAtm.10.1.1.1 |
atmIpoaLisIfMappingIPAddressThis parameter is applicable for
atmIpoaLisIfMappingTypeIP=static(2).
This parameter is the IP Address assigned
by the user when applicable.rw IpAddress .radAtm.10.1.1.2 |
radAtmRtrInAtmArpIntervalThe time interval (in seconds) between sending of
two InATMARP requests.rw Integer32 .radAtm.10.2 |
radAtmRtrInAtmArpAgingTimeThe time (in seconds) that passes until an
entry is deleted, unless this entry
was previously updated by a new inATMARP
request or response.
This variable value should be greater than
the value of radAtmRtrInAtmArpInterval,
so that the entry won't be deleted before
an InATMARP request was sent.rw Integer32 .radAtm.10.3 |