RAD-BROADBAND-IF-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for RAD-BROADBAND-IF-MIB.
118
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
118 total| Object Name |
|---|
broadbandIf OBJECT IDENTIFIER .1.3.6.1.4.1.164.3.1.6.8 |
IMPORTS Unknown .1.3.6.1.4.1.164.3.1.6.8 |
bdbandConfig OBJECT IDENTIFIER .1.3.6.1.4.1.164.3.1.6.8.1 |
prtBdbandIndTableThe Indication Signal table. SEQUENCE OF PrtBdbandIndEntry .1.3.6.1.4.1.164.3.1.6.8.1.1 |
prtBdbandIndEntryAn entry in the Indication Signal table. PrtBdbandIndEntry .1.3.6.1.4.1.164.3.1.6.8.1.1.1 |
prtBdbandCnfgIdxThis object indicates the Idx of the Agent Cnfg the following
objects refer.
255=Temporary Cnfg (when relevant, Set is done only to this configuration).
For Agents that support only one configuration, this object will be
constant=1.ro Integer32 .1.3.6.1.4.1.164.3.1.6.8.1.1.1.1 |
prtBdbandIdxThis object indicates a unique port or interface number.
For numbering, see product's spec.
For some products, the numbering can equal ifIndex.ro Integer32 .1.3.6.1.4.1.164.3.1.6.8.1.1.1.2 |
prtBdbandIndSigThis object indicates a unique Indication Signal.
ais(1) = AIS = Alarm Indication Signal.
rdi(2) = RDI = Remote Defect Indication.ro Enumeration .1.3.6.1.4.1.164.3.1.6.8.1.1.1.3 |
prtBdbandIndEventThis object indicates a unique Event that can cause the Indication Signal.
slm(2) = SLM = Signal Label Mismatch
eed(4) = EED = Excessive Error Defect
pathTrace(5) = the end-to-end source/destination of information is wrong.ro Enumeration .1.3.6.1.4.1.164.3.1.6.8.1.1.1.4 |
prtBdbandIndSigEnableThis object allows user to define if the event specified by prtBdbandIndEvent
will cause creation of the Indication Signal specified by prtBdbandIndSig or not.
disable - will not enable causing the signal
enable - will enable causing the signal.rw Enumeration .1.3.6.1.4.1.164.3.1.6.8.1.1.1.5 |
prtBdbandRowStatusCreation/Deletion of rows in the table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.164.3.1.6.8.1.1.1.6 |
prtPhyConfigTableThe Phy Config table. Used now for Phy25.6 Mbps. SEQUENCE OF PrtPhyConfigEntry .1.3.6.1.4.1.164.3.1.6.8.1.2 |
prtPhyConfigEntryAn entry in the Phy Config table. PrtPhyConfigEntry .1.3.6.1.4.1.164.3.1.6.8.1.2.1 |
prtPhyTimeElapsedThe number of seconds that have elapsed since
the beginning of the current error-measurement period.ro Integer32 .1.3.6.1.4.1.164.3.1.6.8.1.2.1.1 |
prtPhyValidIntervalsThe number of previous intervals for which valid data was collected.
The value will be 96 unless the interface was brought online within
the last 24 hours, in which case the value will be the number of complete
15 minute since the interface has been online.ro Integer32 .1.3.6.1.4.1.164.3.1.6.8.1.2.1.2 |
prtPhyPerfHistory OBJECT IDENTIFIER .1.3.6.1.4.1.164.3.1.6.8.2 |
prtPhyCurrentTableThe 25.6 Mbps Section/Line Current table. SEQUENCE OF PrtPhyCurrentEntry .1.3.6.1.4.1.164.3.1.6.8.2.1 |
prtPhyCurrentEntryAn entry in the 25.6 Mbps Line Current table.
ifIndex of the line 25.6 Mbps layer of type
25.6 Mbps. PrtPhyCurrentEntry .1.3.6.1.4.1.164.3.1.6.8.2.1.1 |
prtPhyCurrentLOSThe counter associated with the number of Loss Of Sync
seconds, encountered by a 25.6 Mbps interface in
the current 15 minute interval.ro Gauge32 .1.3.6.1.4.1.164.3.1.6.8.2.1.1.1 |
prtPhyCurrentLSVThe counter associated with the number of Line symbol violation
seconds, encountered by a 25.6 Mbps
interface in the current 15 minute interval.ro Gauge32 .1.3.6.1.4.1.164.3.1.6.8.2.1.1.2 |
prtPhyCurrentUASThe counter associated with the number of UAS
encountered by a 25.6 Mbps
interface in the current 15 minute interval.ro Gauge32 .1.3.6.1.4.1.164.3.1.6.8.2.1.1.3 |
prtPhyCurrentSESThe counter associated with the number of SES
encountered by a 25.6 Mbps
interface in the current 15 minute interval.ro Gauge32 .1.3.6.1.4.1.164.3.1.6.8.2.1.1.4 |
prtPhyCurrentESThe number of Errored Seconds, encountered by a
25.6 Mbps interface in the current 15 minute interval.ro Gauge32 .1.3.6.1.4.1.164.3.1.6.8.2.1.1.5 |
prtPhyCurrentStatusThe statuses of the current interval:
0 - O.K.
1 - The link has been switched by a redundancy mechanism.
2 - Module is in/out.
4 - Empty - card is out.ro OCTET STRING .1.3.6.1.4.1.164.3.1.6.8.2.1.1.6 |
prtPhyCurrentLOFThe number of Loss of Frames, encountered by an
interface in the current 15 minute interval.ro Gauge32 .1.3.6.1.4.1.164.3.1.6.8.2.1.1.7 |
prtPhyIntervalTableThe Line Interval table. SEQUENCE OF PrtPhyIntervalEntry .1.3.6.1.4.1.164.3.1.6.8.2.2 |
prtPhyIntervalEntryAn entry in the 25.6 Mbps Line Interval table.
ifIndex of the line 25.6 Mbps layer of type 25.6 Mbps. PrtPhyIntervalEntry .1.3.6.1.4.1.164.3.1.6.8.2.2.1 |
prtPhyIntervalNumberA number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes interval
(assuming that all 96 intervals are valid).ro Integer32 .1.3.6.1.4.1.164.3.1.6.8.2.2.1.1 |
prtPhyIntervalLOSThe counter associated with the number of Loss Of Sync
seconds , encountered by a 25.6 Mbps interface in
one of the previous 96, individual 15 minute intervals.ro Gauge32 .1.3.6.1.4.1.164.3.1.6.8.2.2.1.2 |
prtPhyIntervalLSVThe counter associated with the number of line symbol violation
seconds , encountered by a 25.6 Mbps interface in
one of the previous 96, individual 15 minute intervals.ro Gauge32 .1.3.6.1.4.1.164.3.1.6.8.2.2.1.3 |
prtPhyIntervalUASThe counter associated with the number of UAS
encountered by a 25.6 Mbps interface in one of the previous 96,
individual 15 minute intervals.ro Gauge32 .1.3.6.1.4.1.164.3.1.6.8.2.2.1.4 |
prtPhyIntervalSESThe counter associated with the number of SES
encountered by a 25.6 Mbps interface in one of the previous 96,
individual 15 minute intervals.ro Gauge32 .1.3.6.1.4.1.164.3.1.6.8.2.2.1.5 |
prtPhyIntervalESThe number of Errored Seconds, encountered by a
25.6 Mbps interface in one of the previous 96, individual 15
minute intervals.ro Gauge32 .1.3.6.1.4.1.164.3.1.6.8.2.2.1.6 |
prtPhyIntervalStatusThe statuses of the current interval:
0 - O.K.
1 - The link has been switched by a redundancy mechanism.
2 - Module is in/out.
4 - Empty - card is out.ro OCTET STRING .1.3.6.1.4.1.164.3.1.6.8.2.2.1.7 |
prtPhyIntervalLOFThe number of Loss of Frames, encountered by an
interface in one of the previous 96, individual 15
minute intervals.ro Gauge32 .1.3.6.1.4.1.164.3.1.6.8.2.2.1.8 |
r2If OBJECT IDENTIFIER .1.3.6.1.4.1.164.3.1.6.9 |
r2ProfileCnfg OBJECT IDENTIFIER .1.3.6.1.4.1.164.3.1.6.9.1 |
r2CnfgTableThe write operation into the Table Objects is valid only
to the TmpCnfg entry. SEQUENCE OF R2CnfgEntry .1.3.6.1.4.1.164.3.1.6.9.1.1 |
r2CnfgEntryAn entry in table. R2CnfgEntry .1.3.6.1.4.1.164.3.1.6.9.1.1.1 |
r2CnfgIdxThis attribute indicates the Idx of the Cnfg being accessed.
255 = TmpCnfg.
1 = Current Cnfg.
Write is allowed only to TmpCnfg.ro Integer32 .1.3.6.1.4.1.164.3.1.6.9.1.1.1.1 |
r2CnfgProfileIdxProfile Index.
Valid values: 1..5
Only instances of profiles that are defined having agnSigProfType=r2Cas will
exist in this table.ro Integer32 .1.3.6.1.4.1.164.3.1.6.9.1.1.1.2 |
r2ModeR2 Mode.
auto - in this mode, default value of timers will be used by R2,
according to the selected r2Country.
manual - in this mode, user can change the value of R2 timers within the valid
limits, specific to each country.rw Enumeration .1.3.6.1.4.1.164.3.1.6.9.1.1.1.3 |
r2CountryR2 Country. R2 Timers can have different range of values and
defaults for each country. When r2Mode=auto, the default value is
used by R2 according to this selected country.
1=ITU-T (standard values)
2=Korea
3=India
4=Brasil (continuous)
5=Brasil (pulsed)
6..10 - reserved for future countries.rw Integer32 .1.3.6.1.4.1.164.3.1.6.9.1.1.1.4 |
r2DelayThis object enables user to configure the link as satellite or terrestrial.
The seize acknowledge detect timing is much shorter (msec) for
terrestrial link than for satellite link (1-2 sec).rw Enumeration .1.3.6.1.4.1.164.3.1.6.9.1.1.1.5 |
r2MeteringIndWhich Bit will be used for Metering Indication.rw Enumeration .1.3.6.1.4.1.164.3.1.6.9.1.1.1.6 |
r2BreakMakeRatioThis object describes the Break-Make Ratio of Pulse Duration, in [msec].
RW only when r2Mode=manual.rw Enumeration .1.3.6.1.4.1.164.3.1.6.9.1.1.1.7 |
r2ReleaseGuardT2Release Guard timing T2.
Release guard timing before going to idle, in [msec].
RW only when r2Mode=manual.rw Integer32 .1.3.6.1.4.1.164.3.1.6.9.1.1.1.8 |
r2RegretRegret duration, in [sec].
RW only when r2Mode=manual.rw Integer32 .1.3.6.1.4.1.164.3.1.6.9.1.1.1.9 |
r2SeizeDetectSeize Detect. Timer of the R2 incoming side.
Minimum duration to detect a valid seizure, in [msec].
RW only when r2Mode=manual.rw Integer32 .1.3.6.1.4.1.164.3.1.6.9.1.1.1.10 |
r2SeizeAckDelayTimer of the R2 incoming side.
Delay before sending a valid seize ack signal, in [msec].
Applicable only when r2Mode=manual. only when r2Mode=manual.rw Integer32 .1.3.6.1.4.1.164.3.1.6.9.1.1.1.11 |
r2ClearBackDetectTimer of the R2 incoming side.
Minimum duration to recognize a valid clear-back, in [msec].
RW only when r2Mode=manual.rw Integer32 .1.3.6.1.4.1.164.3.1.6.9.1.1.1.12 |
r2ClearFwdDetectTimer of the R2 incoming side.
Minimum duration to recognize a valid clear-forward, in [msec].
RW only when r2Mode=manual.rw Integer32 .1.3.6.1.4.1.164.3.1.6.9.1.1.1.13 |
r2FaultDetectTimer of the R2 incoming side.
Minimum duration to recognize a block signal, in [msec].
RW only when r2Mode=manual.rw Integer32 .1.3.6.1.4.1.164.3.1.6.9.1.1.1.14 |
r2FaultRemoveDetectTimer of the R2 incoming side.
Minimum duration to recognize a valid block removal signal, in [msec].
RW only when r2Mode=manual.rw Integer32 .1.3.6.1.4.1.164.3.1.6.9.1.1.1.15 |
r2MeterPulseDurationTimer of the R2 incoming side.
Duration of metering pulse to be sent, in [msec].
RW only when r2Mode=manual.rw Integer32 .1.3.6.1.4.1.164.3.1.6.9.1.1.1.16 |
r2SeizeAckWaitTimer of the R2 outgoing side.
Minimum duration to receive seizure acknowledge signal, in [msec].
RW only when r2Mode=manual.rw Integer32 .1.3.6.1.4.1.164.3.1.6.9.1.1.1.17 |
r2SeizeAckDetectTimer of the R2 outgoing side.
Minimum duration to recognize a valid seizure acknowledge signal, in [msec].
RW only when r2Mode=manual.rw Integer32 .1.3.6.1.4.1.164.3.1.6.9.1.1.1.18 |
r2AnswerDetectTimer of the R2 outgoing side.
Minimum duration to recognize a valid answer signal, in [msec].
RW only when r2Mode=manual.rw Integer32 .1.3.6.1.4.1.164.3.1.6.9.1.1.1.19 |
r2BlockRemoveDetectTimer of the R2 outgoing side.
Minimum duration to recognize a valid block removal signal, in [msec].
RW only when r2Mode=manual.rw Integer32 .1.3.6.1.4.1.164.3.1.6.9.1.1.1.20 |
r2MeterPulseDetectTimer of the R2 outgoing side.
Minimum duration of incoming meter pulse, in [msec].
RW only when r2Mode=manual.rw Integer32 .1.3.6.1.4.1.164.3.1.6.9.1.1.1.21 |
r2ForcedDisconnectTimer of the R2 outgoing side.
Minimum duration to recognize disconnect signal, in [msec].
RW only when r2Mode=manual.rw Integer32 .1.3.6.1.4.1.164.3.1.6.9.1.1.1.22 |
r2DisconnectAckTimer of the R2 outgoing side.
Minimum duration to recognize disconnect acknowledge signal, in [msec].
RW only when r2Mode=manual.rw Integer32 .1.3.6.1.4.1.164.3.1.6.9.1.1.1.23 |
r2ReleaseGuardT1Timer of the R2 outgoing side.
Minimum duration to release guard, in [msec].
During this time, no new call can be initiated.
RW only when r2Mode=manual.rw Integer32 .1.3.6.1.4.1.164.3.1.6.9.1.1.1.24 |
r2CnfgRowStatusThis object enables the user to add/delete entries to/from the table.rw RowStatus --active(1), --destroy(6) .1.3.6.1.4.1.164.3.1.6.9.1.1.1.25 |
r2TsTableThe write operation into the Table Objects is valid only
to the TmpCnfg entry. SEQUENCE OF R2TsEntry .1.3.6.1.4.1.164.3.1.6.9.1.2 |
r2TsEntryAn entry in table. R2TsEntry .1.3.6.1.4.1.164.3.1.6.9.1.2.1 |
r2TsCnfgIdxThis attribute indicates the Idx of the Cnfg being accessed.
255 = TmpCnfg.
1 = Current Cnfg.
Write is allowed only to TmpCnfg.ro Integer32 .1.3.6.1.4.1.164.3.1.6.9.1.2.1.1 |
r2TsProfileIdxProfile Index.
Valid values: 1..5
Only instances of profiles that are defined having agnSigProfType=r2Cas will
exist in this table.ro Integer32 .1.3.6.1.4.1.164.3.1.6.9.1.2.1.2 |
r2TsIdxTS Index.
Valid values: 1..31ro Integer32 .1.3.6.1.4.1.164.3.1.6.9.1.2.1.3 |
r2TsCallEnableThis object indicates the Enabled Call direction for the specific TS.rw Enumeration .1.3.6.1.4.1.164.3.1.6.9.1.2.1.4 |
r2TsMeteringThis object indicates if the specific TS should support Metering.rw Enumeration .1.3.6.1.4.1.164.3.1.6.9.1.2.1.5 |
r2TsRowStatusThis object enables the user to add/delete entries to/from the table.rw RowStatus --active(1), --destroy(6) .1.3.6.1.4.1.164.3.1.6.9.1.2.1.6 |
r2TsReversePolarityThis object indicates if the specific TS should support Reverse Polarity.rw Enumeration .1.3.6.1.4.1.164.3.1.6.9.1.2.1.7 |
r2IfStatus OBJECT IDENTIFIER .1.3.6.1.4.1.164.3.1.6.9.2 |
r2StatusTableThe write operation into the Table Objects is valid only
to the TmpCnfg entry. SEQUENCE OF R2StatusEntry .1.3.6.1.4.1.164.3.1.6.9.2.1 |
r2StatusEntryAn entry in table. R2StatusEntry .1.3.6.1.4.1.164.3.1.6.9.2.1.1 |
r2StatusSlotIdxSlot Indexro Enumeration .1.3.6.1.4.1.164.3.1.6.9.2.1.1.1 |
r2StatusPortIdxThis object indicates a unique port number of the ML having
R2 interface.
Valid values: exPrt1 (1)..exPrt4 (4)ro Integer32 .1.3.6.1.4.1.164.3.1.6.9.2.1.1.2 |
r2StatusTsIdxTime Slot index.ro Integer32 .1.3.6.1.4.1.164.3.1.6.9.2.1.1.3 |
r2StatusSigDirectionR2 Time Slot Signaling Direction.ro Enumeration .1.3.6.1.4.1.164.3.1.6.9.2.1.1.4 |
r2StatusTsStateR2 TS Statero Enumeration .1.3.6.1.4.1.164.3.1.6.9.2.1.1.5 |
r2StatusProtocolStateR2 Protocol State.ro Enumeration .1.3.6.1.4.1.164.3.1.6.9.2.1.1.6 |
atmLayer2 OBJECT IDENTIFIER .radAtm.7 |
atmLayer2XVclTableThis table is an extension of VCL table, which is created
for each LAN VCC. SEQUENCE OF AtmLayer2XVclEntry .radAtm.7.1 |
atmLayer2XVclEntryConceptual row in atmVclTable.
This table augments the RFC2515 VCL table. AtmLayer2XVclEntry .radAtm.7.1.1 |
atmLayer2XVclConnModeEach valid LAN VCC is either Main or Sub.
This parameter is configured only once on creation of a LAN VCC.
It can not be changed after creation. In order to change the Mode,
user should delete the connection and create a new one.
main - A LAN VCC, which holds its own bridge port.
Bridge forwarding and Bridge learning is performed only on Main
VCCs.
For working on a transparent bridge, that doesn't perform
layer 2 priority mapping, a Main VCC should be opened, which
is the default connection Mode.
When working with layer 2 priority, a group of LAN VCCs should
be configured, where each group will be associated with only
one Main VCC.
A specific Main can not be used by more than one group.
sub - A LAN VCC is not part of the bridging mechanism.
A Sub VCC automatically inherit some general definitions from
Main VCC of its group: ATM Slot/Port and LAN Slot/Port.
Max number of Sub VCCs allowed per group is:
[Number of Priorities - 1].rw Enumeration .radAtm.7.1.1.1 |
atmLayer2XVclGroupIdxThe group identifier.
A VCC Group identifier = 0 if the VCC was not associated with a
group yet.
This value is updated according to the group identifier set by
atmLayer2GroupTable.ro Integer32 .radAtm.7.1.1.2 |
atmLayer2GroupTableThis table contains groups and their members.
A group is a bundle of VCCs, which acts as different queues.
Main and Sub VCCs should have the same ATM slot and port,
and the same LAN slot and port.
Each group contains: 1 to <number of priorities> VCCs. SEQUENCE OF AtmLayer2GroupEntry .radAtm.7.2 |
atmLayer2GroupEntryConceptual row in atmLayer2GroupTable.
The indexes: ifIndex, atmVclVpi and atmVclVci indicate
the Network ATM End-Point.
Upon a group creation, one Main VCC must be added first.
After the group was created, Sub VCCs may be added to the group. AtmLayer2GroupEntry .radAtm.7.2.1 |
atmLayer2GroupIdxThe group identifier.
0 is not a valid index.ro Integer32 .radAtm.7.2.1.1 |
atmLayer2GroupRowStatusCreation/Deletion of rows in the table, and indication of the
entry's status.rw RowStatus (SNMPv2-TC) .radAtm.7.2.1.2 |
atmLayer2GroupConnModeEach valid LAN VCC is either Main or Sub as configured in
atmLayer2XVclTable.ro Enumeration .radAtm.7.2.1.3 |
atmLayer2GroupConnPriorityThis parameter is configured by atmLayer2PriorityRx from
atmLayer2PriorityTable.
Each bit in the Octet represents a specific priority as follows:
MSB 7 6 5 4 3 2 1 0 LSB -> Priorities
||
1 0 0 1 0 0 0 1 -> Value
In this example, a certain VCC has several priorities: 0, 4 and 7.ro OCTET STRING .radAtm.7.2.1.4 |
atmLayer2GroupNameGroup name. Configured by the user.
The name is unique per system.
For atmLayer2GroupIdx=0, the name will be null.rw SnmpAdminString .radAtm.7.2.1.5 |
atmLayer2PriorityTableThis table maps all priorities inside a group.
Several priorities might be mapped to the same VCC.
Upon priority change, the agent will update the VCCs of the
changed priority in this table, and will update -
atmLayer2GroupConnPriority parameter of both former and new owners
of the changed priority.
Changing a VCC value is actually a change of three parameters
simultaneously: atmLayer2PriorityIfIndex, atmLayer2PriorityVclVpi
and atmLayer2PriorityVclVci. Otherwise, the set will be rejected,
since there might be that such VCC doesn't exist in the specific
group. SEQUENCE OF AtmLayer2PriorityEntry .radAtm.7.3 |
atmLayer2PriorityEntryConceptual row in atmLayer2PriorityTable.
Each entry is a Network ATM End-Point per priority.
Upon a group creation, all priorities are mapped to the Main VCC.
Number of entries per group is according to the number of
priorities enabled. (For example, for Max priorities = 8,
the agent will create 8 entries). AtmLayer2PriorityEntry .radAtm.7.3.1 |
atmLayer2PriorityGroupIdxThe group identifier.ro Integer32 .radAtm.7.3.1.1 |
atmLayer2PriorityRxThe priority values.
The used values are 0-7, but since this value is part of the index
of the table, and in order to avoid '0' as an index, the index syntax
is 1..8, but the real value is atmLayer2PriorityRx-1:
0 - for Low priority.
7 - for High priority.ro Integer32 .radAtm.7.3.1.2 |
atmLayer2PriorityIfIndexATM ifIndex of the network End-Point.rw InterfaceIndex (IF-MIB) .radAtm.7.3.1.3 |
atmLayer2PriorityVclVpiVpi of the network End-Point.rw Integer32 .radAtm.7.3.1.4 |
atmLayer2PriorityVclVciVci of the network End-Point.rw Integer32 .radAtm.7.3.1.5 |
atmLayer2GroupIndexNextThis object contains an appropriate value to
be used for atmLayer2GroupIdx when creating
entries in the atmLayer2GroupTable. The value
0 indicates that no unassigned entries are
available. To obtain the atmLayer2GroupIdx
value for a new entry, the manager gets
the current value of this object. The next index
will be of the first unassigned entry. It will be
provided by checking the assigned entries.ro Integer32 .radAtm.7.4 |
atmLayer2CfgTableBridge configuration Table. This table supports multi-bridge
and bridge features within an ATM device. SEQUENCE OF AtmLayer2CfgEntry .radAtm.7.5 |
atmLayer2CfgEntryConceptual row in atmLayer2CfgTable.
Each entry in this table contains the bridging attributes for
both Ethernet and ATM sides.
The interface index is the Ethernet port interface.
For Ace52: this object represents the Bridge ifIndex. AtmLayer2CfgEntry .radAtm.7.5.1 |
atmLayer2CfgBridgingModeBridging mode can be one of the following:
ATM <> Ethernet - Bridging is between the Ethernet
port and the ATM port (there is no bridging between VCs).
ATM <> Ethernet + ATM - Bridging is done both between
the Ethernet port and the ATM port and also between VCs.rw Enumeration .radAtm.7.5.1.1 |
atmLayer2CfgVlanModeVLAN Mode. Upon Mode changing, all LAN VCCs will be deleted
by the agent from all tables that include LAN VCCs.rw Enumeration .radAtm.7.5.1.2 |
atmLayer2CfgAtmAcceptableFrameTypeThe Frame Type that will be acceptable by the VCCs that
are associated with this Ethernet port.
Frames which don't match the selected type will be discarded.
admitAll - all frames will be accepted.
admitOnlyVlanTagged - only Tagged frames will be accepted.
admitOnlyUnTagged - only unTagged frames will be accepted.rw Enumeration .radAtm.7.5.1.3 |
atmLayer2CfgAtmIngressFilteringFor the VCCs that are associated with this Ethernet port,
when this is true(1) the device will discard incoming
frames for VLANs which do not include this Port in its
Member set. When false(2), the port will accept all
incoming frames.rw TruthValue (SNMPv2-TC) .radAtm.7.5.1.4 |
atmLayer2CfgAtmTxFrameTypeThe Frame Type that will be transmitted by the VCCs that
are associated with this Ethernet port.
unTagged - The transmitted frames will be unTagged.
tagged - The transmitted frames will be Tagged.rw Enumeration .radAtm.7.5.1.5 |
atmLayer2CfgEthAcceptableFrameTypeThe Frame Type that this Ethernet port will accept.
(for ACE-52: the Frame Type that this Bridge will accept)
This parameter is notApplicable for atmLayer2VlanMode=disable.
Frames which don't match the selected type will be discarded.
admitAll - all frames will be accepted.
admitOnlyVlanTagged - only Tagged frames will be accepted.
admitOnlyUnTagged - only unTagged frames will be accepted.rw Enumeration .radAtm.7.5.1.6 |
atmLayer2CfgBridgeActionThis object enables to perform the specified action on the
selected port.rw Enumeration .radAtm.7.5.1.7 |
atmLayer2CfgLearningModeThis object specifies the mode of the learning process of a bridge.
svl - Shared VLAN process. If an individual MAC Address is learned
in one VLAN, this information is used in forwarding decisions
taken for that address for all other VLANs.
ivl - Independent VLAN process. If an individual MAC Address is learned
in one VLAN, this information is not used in forwarding decisions
taken for that address for all other VLANs.rw Enumeration .radAtm.7.5.1.8 |
atmLayer2CfgAgingTimeThe timeout period in seconds for aging out
dynamically learned forwarding information.rw Integer32 .radAtm.7.5.1.9 |
radAtmFr OBJECT IDENTIFIER .radAtm.8 |
frAtmIwfXConnectionTableThis table is an extension of frAtmIwfXConnectionTable from
RFC2955. SEQUENCE OF FrAtmIwfXConnectionEntry .radAtm.8.1 |
frAtmIwfXConnectionEntryConceptual row in frAtmIwfXConnectionTable.
This table augments the RFC2955. FrAtmIwfXConnectionEntry .radAtm.8.1.1 |
frAtmIwfXConnModeFR IWF Mode.
service - Service InterWorking (FRF.8),
network - Network InterWorking (FRF.5).rw Enumeration .radAtm.8.1.1.1 |
frAtmIwfXConnSscsDlciThis parameter is relevant for
frAtmIwfXConnMode=network (FRF.5) only.
This parameter allow configuration of the
FR SSCS DLCI that is transferred to the
remote FR unit.rw Integer32 .radAtm.8.1.1.2 |