PRVT-JDSU-MIB
The PRVT-JDSU-MIB module enables SNMP-based monitoring and configuration of JDSU (now Viavi Solutions) optical transport and access network equipment, specifically managing private network attributes such as port statistics, error counters, and interface operational states.
Imported Objects
Objects
17 total| Object Name |
|---|
prvtJdsuMibThis MIB provide control and analisys for JDSU functionality. MODULE-IDENTITY .1.3.6.1.4.1.5205.2.137 |
prvtJdsuNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.5205.2.137.0 |
prvtJdsuAdminStateChangeThis trap should be sent whenever a JDSU admins state is changed
for a specific interface. NOTIFICATION-TYPE .1.3.6.1.4.1.5205.2.137.0.1 |
prvtJdsuOperStateChangeThis trap should be sent whenever a JDSU state is changed
on a specific interface. NOTIFICATION-TYPE .1.3.6.1.4.1.5205.2.137.0.2 |
prvtJdsuObjects OBJECT IDENTIFIER .1.3.6.1.4.1.5205.2.137.1 |
prvtJdsuLoopback OBJECT IDENTIFIER .1.3.6.1.4.1.5205.2.137.1.1 |
prvtJdsuLoopbackTableThis table holds the configuration for JDSU loopback SEQUENCE OF PrvtJdsuLoopbackEntry .1.3.6.1.4.1.5205.2.137.1.1.1 |
prvtJdsuLoopbackEntryNONE PrvtJdsuLoopbackEntry .1.3.6.1.4.1.5205.2.137.1.1.1.1 |
prvtJdsuLoopbackAdminStatusJDSU remote loopback admin status.
This can be used to either enable or disable JDSU loopback on a
certain interface.
Forced parameter is used for manually set loopback.
Remote parameter is used for JDSU remote operation.rw Enumeration .1.3.6.1.4.1.5205.2.137.1.1.1.1.1 |
prvtJdsuLoopbackRemoteMacRemote MAC address of the device for JDSU loopback testing.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.5205.2.137.1.1.1.1.2 |
prvtJdsuLoopbackRemoteInnerVlanThis is used as the VLAN tag in case of single encapsulated packets
or as the inner VLAN tag in case of dual encapsulated packets.rw VlanId (Q-BRIDGE-MIB) .1.3.6.1.4.1.5205.2.137.1.1.1.1.3 |
prvtJdsuLoopbackRemoteOuterVlanThe outer VLAN tag in case of dual encapsulated packets.rw VlanId (Q-BRIDGE-MIB) .1.3.6.1.4.1.5205.2.137.1.1.1.1.4 |
prvtJdsuLoopbackOperationalStatusJDSU remote loopback current operational status.ro Enumeration .1.3.6.1.4.1.5205.2.137.1.1.1.1.5 |
prvtJdsuLoopbackRowStatusThe status of the row entry.
The writable columns in a row can not be changed if the row
is active. Certain columns must have a valid value before a row
can be activated.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.5205.2.137.1.1.1.1.6 |
prvtJdsuConformance OBJECT IDENTIFIER .1.3.6.1.4.1.5205.2.137.2 |
prvtJdsuCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.5205.2.137.2.1 |
prvtJdsuGroups OBJECT IDENTIFIER .1.3.6.1.4.1.5205.2.137.2.2 |
More MIBs from xxx Tech
Browse all xxx TechMIBs →The SIGNAMAX-SW0657851-MIB module enables SNMP-based monitoring and management of Signamax LLC's specific switch hardware, exposing standard interface statistics, port states, and system resource metrics for network performance analysis.
SNMP MIB module
The PRIVATE-SW0657840-MIB module provides vendor-specific extensions for xxx Tech network switches, enabling the monitoring of proprietary hardware telemetry, internal interface states, and device-specific performance counters not covered by standard MIBs. This module facilitates granular fault isolation and resource utilization tracking for xxx Tech switch platforms via SNMP.
The PRIVATE-FEL2Mod-SW24-MIB provides vendor-specific monitoring for xxx Tech Layer 2 switch hardware, exposing private OID extensions for interface statistics, port states, and device operational parameters not covered by standard MIBs. This module enables granular visibility into proprietary switch metrics and internal subsystem states for the xxx Tech SW24 platform.
The PRVT-STATISTICS-CES-MIB module monitors private Circuit Emulation Service (CES) performance counters and error statistics for TDM-over-Packet networks, specifically capturing metrics such as cell loss, delay variation, and synchronization errors that fall outside the scope of standard SONET and DS1 MIBs.
SNMP MIB module