PRVT-CES-MIB
This module includes configuration parameters for DS1 modules not included in DS1-MIB.
Main OID:
prvtCESMib.1.3.6.1.4.1.5205.2.111
104
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
104 total| Object Name |
|---|
prvtCESMibThis module includes configuration parameters for DS1 modules not included in
DS1-MIB. MODULE-IDENTITY .1.3.6.1.4.1.5205.2.111 |
prvtCESNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.5205.2.111.0 |
prvtCESDsx1AlarmThis notification is sent when the value of a TDM port error condition statistic has exceeded the
configured threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.5205.2.111.0.1 |
prvtCESModuleAvailableprvtCESModuleAvailable trap NOTIFICATION-TYPE .1.3.6.1.4.1.5205.2.111.0.2 |
prvtCESModuleUnAvailableDueExtractprvtCESModuleUnAvailableDueExtract trap. NOTIFICATION-TYPE .1.3.6.1.4.1.5205.2.111.0.3 |
prvtCESModuleUnAvailableDueReloadprvtCESModuleUnAvailableDueReload trap NOTIFICATION-TYPE .1.3.6.1.4.1.5205.2.111.0.4 |
prvtCESObjects OBJECT IDENTIFIER .1.3.6.1.4.1.5205.2.111.1 |
prvtCESDsx1ExtTableThis table contains object for configuring DS1 interfaces, not supported in dsx1ConfigTable. SEQUENCE OF PrvtCESDsx1ExtEntry .1.3.6.1.4.1.5205.2.111.1.1 |
prvtCESDsx1ExtEntryprvtCESDsx1ExtEntry PrvtCESDsx1ExtEntry .1.3.6.1.4.1.5205.2.111.1.1.1 |
prvtCESE1ImpedanceThis object configures temination impedance for TDM ports if the line type is E1.rw E1Impedance .1.3.6.1.4.1.5205.2.111.1.1.1.1 |
prvtCEST1GainLimitThis object configures Tx or Rx gain limit for TDM ports if the line type is T1.rw T1GainLimit .1.3.6.1.4.1.5205.2.111.1.1.1.2 |
prvtCESPortShutdownShutdown TDM port.rw Enumeration .1.3.6.1.4.1.5205.2.111.1.1.1.3 |
prvtCESPortLineTypeAdditional line types. For reference see object dsx1LineTyperw Enumeration .1.3.6.1.4.1.5205.2.111.1.1.1.4 |
prvtCEST1LongCableLengthLong cable length options for T1 mode.rw T1LongCableLength .1.3.6.1.4.1.5205.2.111.1.1.1.5 |
prvtCESPortOperStatusTDM link state.ro Enumeration .1.3.6.1.4.1.5205.2.111.1.1.1.6 |
prvtCESClearPortStatisticsClear port statistics.rw Enumeration .1.3.6.1.4.1.5205.2.111.1.1.1.7 |
prvtCESServiceClockService Clock available only for DS1 interface.rw ServiceClock .1.3.6.1.4.1.5205.2.111.1.1.1.8 |
prvtCESModuleConfTableThis table contains object for configuring options that are applied to the entire module. SEQUENCE OF PrvtCESModuleConfEntry .1.3.6.1.4.1.5205.2.111.1.2 |
prvtCESModuleConfEntryprvtCESModuleConfEntry PrvtCESModuleConfEntry .1.3.6.1.4.1.5205.2.111.1.2.1 |
prvtCESModuleIndexIndex of each CES module installed.ro Integer32 .1.3.6.1.4.1.5205.2.111.1.2.1.1 |
prvtCESModuleLineTypeLine mode for the module.rw CESLineType .1.3.6.1.4.1.5205.2.111.1.2.1.2 |
prvtCESModuleTxClockConfigures Transmit Source Clock for the module.rw Enumeration .1.3.6.1.4.1.5205.2.111.1.2.1.3 |
prvtCESModuleTxBackupClockConfigures Backup Clock for the module.rw Enumeration .1.3.6.1.4.1.5205.2.111.1.2.1.4 |
prvtCESModuleConfigWhen this object is set to applyConfiguration(2), the module is restarted
and the changes in dsx1ConfigTable or prvtCESConfTable are applied. The object
must be set to rejectConfiguration(3) to remove unapplied changes. If the object
is set to restart(4), the module is restarted with applying the changes.
This object always returns a value of noop(1) when get.rw ConfigAction .1.3.6.1.4.1.5205.2.111.1.2.1.5 |
prvtCESModuleIPAddressThe CES Module IP address after configuration is applied.rw IpAddress .1.3.6.1.4.1.5205.2.111.1.2.1.6 |
prvtCESModuleIPAddressMaskThe CES Module IP address mask after configuration is applied.rw IpAddress .1.3.6.1.4.1.5205.2.111.1.2.1.7 |
prvtCESModuleGatewayCES Module Gateway after configuration is applied.rw IpAddress .1.3.6.1.4.1.5205.2.111.1.2.1.8 |
prvtCESModuleUpTimeCES Up Timero TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.5205.2.111.1.2.1.9 |
prvtCESModuleMACAddressCES MAC Addressro OCTET STRING .1.3.6.1.4.1.5205.2.111.1.2.1.10 |
prvtCESModuleHardwareRevisionCES Hardware revisionro OCTET STRING .1.3.6.1.4.1.5205.2.111.1.2.1.11 |
prvtCESModuleFirmwareVersionCES Firmware revisionro OCTET STRING .1.3.6.1.4.1.5205.2.111.1.2.1.12 |
prvtCESModuleClearCircuitStatisticsClear circuits statistics.rw Enumeration .1.3.6.1.4.1.5205.2.111.1.2.1.13 |
prvtCESModuleLbitEnable/disable L bit set upon AIS
defect detection, in structure agnostic mode.rw Enumeration .1.3.6.1.4.1.5205.2.111.1.2.1.14 |
prvtCESModulePolicyLopsControls policy lops. Object does not require module to be restarted.rw Enumeration .1.3.6.1.4.1.5205.2.111.1.2.1.15 |
prvtCESModulePolicyLbitControls policy lbit. Object does not require module to be restarted.rw Enumeration .1.3.6.1.4.1.5205.2.111.1.2.1.16 |
prvtCESModulePolicyRbitControls policy rbit. Object does not require module to be restarted.rw Enumeration .1.3.6.1.4.1.5205.2.111.1.2.1.17 |
prvtCESModulePolicyRdControls policy rd. Object does not require module to be restarted.rw Enumeration .1.3.6.1.4.1.5205.2.111.1.2.1.18 |
prvtCESModulePolicyIdlePatternControls policy idle pattern. Object does not require module to be restarted.rw Unsigned32 .1.3.6.1.4.1.5205.2.111.1.2.1.19 |
prvtCESModulePolicyIdleSignallingControls policy idle signalling. Object does not require module to be restarted.rw Unsigned32 .1.3.6.1.4.1.5205.2.111.1.2.1.20 |
prvtCESModulePolicyLopsEnterControls the number of consecutive missed
packets required to enter LOPS state.
Object does not require module to be restarted.rw Integer32 .1.3.6.1.4.1.5205.2.111.1.2.1.21 |
prvtCESModulePolicyLopsExitControls the number of consecutive missed
packets required to exit LOPS state.
Object does not require module to be restarted.rw Integer32 .1.3.6.1.4.1.5205.2.111.1.2.1.22 |
prvtCESModulePolicyuUnstrLbitIf a packet is received with L bit set, and the payload is present (not suppressed),
one of the following is sent to the TDM line, according to a globally configurable unstructured L-flag policy:
The AIS pattern all-one
The received payload as-is nonerw Enumeration .1.3.6.1.4.1.5205.2.111.1.2.1.23 |
prvtCESModulePolicyuStrReplaceIf a missing packet is detected, one of the following is sent to the TDM line,
according to a globally configurable structured missing packet replacement policy:
The AIS pattern all-one on the relevant timeslots
The configured IDLE patternrw Enumeration .1.3.6.1.4.1.5205.2.111.1.2.1.24 |
prvtCESModulePolicyuUnstrReplaceIf a missing packet is detected, one of the following is sent to the TDM line,
according to a globally configurable unstructured missing packet replacement policy:
The AIS pattern all-one
The configured IDLE patternrw Enumeration .1.3.6.1.4.1.5205.2.111.1.2.1.25 |
prvtCESModulePolicyuUnstrLopsIf a CES circuit enters the LOPS state, one of the following is sent to the TDM line,
according to a globally configurable unstructured missing packet replacement policy:
The AIS pattern all-one
The contents of the jitter buffer - nonerw Enumeration .1.3.6.1.4.1.5205.2.111.1.2.1.26 |
prvtCESModuleServiceClockClock mode for CES modulerw ServiceClock .1.3.6.1.4.1.5205.2.111.1.2.1.27 |
prvtCESModulePolicyuUnstrReplacePatternUnstructured packet replace policy pattern numberrw Integer32 .1.3.6.1.4.1.5205.2.111.1.2.1.28 |
prvtCESUnappTableThis table displays CES module configuration which will take effect
after prvtCESModuleConf is set to applyConfiguration(2). SEQUENCE OF PrvtCESUnappEntry .1.3.6.1.4.1.5205.2.111.1.3 |
prvtCESUnappEntryprvtCESUnappEntry PrvtCESUnappEntry .1.3.6.1.4.1.5205.2.111.1.3.1 |
prvtCESUnappLineTypeThe value of dsx1LineType before configuration is applied.ro Enumeration .1.3.6.1.4.1.5205.2.111.1.3.1.1 |
prvtCESUnappLineCodingThe value of dsx1LineCoding before configuration is applied.ro Enumeration .1.3.6.1.4.1.5205.2.111.1.3.1.2 |
prvtCESUnappLoopbackConfigThe value of dsx1LoopbackConfig before configuration is applied.ro Enumeration .1.3.6.1.4.1.5205.2.111.1.3.1.3 |
prvtCESUnappSignalModeThe value of dsx1SignalMode before configuration is applied.ro Enumeration .1.3.6.1.4.1.5205.2.111.1.3.1.4 |
prvtCESUnappTransmitClockSourceThe value of dsx1TransmitClockSource before configuration is applied.ro Enumeration .1.3.6.1.4.1.5205.2.111.1.3.1.5 |
prvtCESUnappTransmitClockBackupThe value of dsx1TransmitClockBackup before configuration is applied.ro Enumeration .1.3.6.1.4.1.5205.2.111.1.3.1.6 |
prvtCESUnappLineLengthThe value of dsx1LineLength before configuration is applied.ro Integer32 .1.3.6.1.4.1.5205.2.111.1.3.1.7 |
prvtCESUnappLineModeThe value of dsx1LineMode before configuration is applied.ro Enumeration .1.3.6.1.4.1.5205.2.111.1.3.1.8 |
prvtCESUnappLineBuildOutThe value of dsx1LineBuildOut before configuration is applied.ro Enumeration .1.3.6.1.4.1.5205.2.111.1.3.1.9 |
prvtCESUnappE1ImpedanceThe value of prvtCESE1Impedance before configuration is applied.ro E1Impedance .1.3.6.1.4.1.5205.2.111.1.3.1.10 |
prvtCESUnappT1GainLimitThe value of prvtCEST1GainLimit before configuration is applied.ro T1GainLimit .1.3.6.1.4.1.5205.2.111.1.3.1.11 |
prvtCESUnappIPAddressThe CES Module IP address before configuration is applied.ro IpAddress .1.3.6.1.4.1.5205.2.111.1.3.1.12 |
prvtCESUnappIPAddressMaskThe CES Module IP address mask before configuration is applied.ro IpAddress .1.3.6.1.4.1.5205.2.111.1.3.1.13 |
prvtCESUnappGatewayThe CES Module Gateway before configuration is applied.ro IpAddress .1.3.6.1.4.1.5205.2.111.1.3.1.14 |
prvtCESDsx1AlarmTableThis table contains object for configuring and displaying TDM ports TCA thresholds. SEQUENCE OF PrvtCESDsx1AlarmEntry .1.3.6.1.4.1.5205.2.111.1.4 |
prvtCESDsx1AlarmEntryprvtCESDsx1AlarmEntry PrvtCESDsx1AlarmEntry .1.3.6.1.4.1.5205.2.111.1.4.1 |
prvtCESDsx1AlarmPortThe DS1 port for which this alarm is configured. Integer32 .1.3.6.1.4.1.5205.2.111.1.4.1.1 |
prvtCESDsx1AlarmIndexAn integer uniquely identifying an alarm entry. Gauge32 .1.3.6.1.4.1.5205.2.111.1.4.1.2 |
prvtCESDsx1AlarmVariableThe OID of the variable whose value is being monitored. Depending on the time interval,
the error condition and the ifIndex of the TDM interface, this points to an object from an entry in
dsx1CurrentTable or dsx1TotalTable.ro OBJECT IDENTIFIER .1.3.6.1.4.1.5205.2.111.1.4.1.3 |
prvtCESDsx1AlarmThresholdThe alarm condition threshold for this alarm entry. The alarm is triggered if the value of the
object pointed by prvtCESDsx1AlarmVariable remains above this threshold for more than 3 seconds.rw Integer32 .1.3.6.1.4.1.5205.2.111.1.4.1.4 |
prvtCESDsx1AlarmValueThe value of the object pointed to by prvtCESDsx1AlarmVariable, present for notification purposes.ro Integer32 .1.3.6.1.4.1.5205.2.111.1.4.1.5 |
prvtCESAlarmMonitorCES alarm monitorrw Enumeration .1.3.6.1.4.1.5205.2.111.1.5 |
prvtCESCICTableThis table contains objects for configuring Clock Input Controller. SEQUENCE OF PrvtCESCICEntry .1.3.6.1.4.1.5205.2.111.1.6 |
prvtCESCICEntryprvtCESCICEntry PrvtCESCICEntry .1.3.6.1.4.1.5205.2.111.1.6.1 |
prvtCESCICModuleIdSlot of CES module installed. Integer32 .1.3.6.1.4.1.5205.2.111.1.6.1.1 |
prvtCESCICNumberAn integer uniquely identifying a Clock Input Controller. Gauge32 .1.3.6.1.4.1.5205.2.111.1.6.1.2 |
prvtCESCICClockNumberThis variable indicates the index of the clock
the clock input controller belongs toro Integer32 .1.3.6.1.4.1.5205.2.111.1.6.1.3 |
prvtCESCICModeThe mode of the clock input controller. Not
all clock input controllers support all modes.
The clock input controller status is 'locked'
only if the clock input controller is in
'normal' mode.ro Enumeration .1.3.6.1.4.1.5205.2.111.1.6.1.4 |
prvtCESCICTdmPortIf the clock input controller recovers a clock
from a port , this variable indicates the
TDM Port. Otherwise, it must
be set to zero.rw Integer32 .1.3.6.1.4.1.5205.2.111.1.6.1.5 |
prvtCESCICCircuitIf the clock input controller recovers a clock
from a circuit, this variable indicates the
circuit ID. Otherwise, it
must be set to zero.rw Integer32 .1.3.6.1.4.1.5205.2.111.1.6.1.6 |
prvtCESCICStatusThe status of the input reference.Reference
is ok when the status is 'locked'. Otherwise,
the status is 'notLocked'. Alternatively, if an
error was detected at the input, the status
indicates this error.ro Enumeration .1.3.6.1.4.1.5205.2.111.1.6.1.7 |
prvtCESCICStateThe state is set to 'active' if the input
controller was selected by the clock to drive
the clock output. At least one input out of
the clock-input-controllers attached to a
clock must be in an 'active' state at any given
timero Enumeration .1.3.6.1.4.1.5205.2.111.1.6.1.8 |
prvtCESCICMappTableThis table contains clock configuration and status monitoring information. SEQUENCE OF PrvtCESCICMappEntry .1.3.6.1.4.1.5205.2.111.1.7 |
prvtCESCICMappEntryprvtCESCICMappEntry PrvtCESCICMappEntry .1.3.6.1.4.1.5205.2.111.1.7.1 |
prvtCESCICMappModuleIdSlot of CES module installed.ro Integer32 .1.3.6.1.4.1.5205.2.111.1.7.1.1 |
prvtCESCICMappClockNumberIndex for the conceptual row
identifying a clock within this
mapping tablero Gauge32 .1.3.6.1.4.1.5205.2.111.1.7.1.2 |
prvtCESCICMappCICNumberIndex for the conceptual row
identifying a clock input within
this mapping tablero Gauge32 .1.3.6.1.4.1.5205.2.111.1.7.1.3 |
prvtCESCICMappStateThe state is set to 'active' if the input
controller was selected by the clock to drive
the clock output. At least one input out of
the clock-input-controllers attached to a
clock must be in an 'active' state at any given
time This value of this variable is
equal to the prvtCESCICState
variable in the CIC tablero Enumeration .1.3.6.1.4.1.5205.2.111.1.7.1.4 |
prvtCESApsTableThis table contains objects needed APS configuration SEQUENCE OF PrvtCESApsEntry .1.3.6.1.4.1.5205.2.111.1.8 |
prvtCESApsEntryprvtCESApsEntry PrvtCESApsEntry .1.3.6.1.4.1.5205.2.111.1.8.1 |
prvtCESApsModuleIdAn integer uniquely identifying slot of the CES module installed Integer32 .1.3.6.1.4.1.5205.2.111.1.8.1.1 |
prvtCESApsEnableEnable/Disable Automatic Protection Switchingrw Enumeration .1.3.6.1.4.1.5205.2.111.1.8.1.2 |
prvtCESApsActiveLineAPS active linerw Integer32 .1.3.6.1.4.1.5205.2.111.1.8.1.3 |
prvtSdBerThresholdThe Signal Degrade Bit Error Rate.
The negated value of this number is used
as the exponent of 10 for computing the
threshold value for the Bit Error Rate
(BER). For example, a value of 5 indicates
a BER threshold of 10^-5.rw Integer32 .1.3.6.1.4.1.5205.2.111.1.8.1.4 |
prvtSfBerThresholdThe Signal Failure Bit Error Rate.
The negated value of this number is used
as the exponent of 10 for computing the
threshold value for the Bit Error Rate
(BER). For example, a value of 5 indicates
a BER threshold of 10^-5.rw Integer32 .1.3.6.1.4.1.5205.2.111.1.8.1.5 |
prvtCESUpdateFirmwareTableThis table contains object needed in update firmware of CES module SEQUENCE OF PrvtCESUpdateFirmwareEntry .1.3.6.1.4.1.5205.2.111.1.9 |
prvtCESUpdateFirmwareEntryprvtCESUpdateFirmwareEntry PrvtCESUpdateFirmwareEntry .1.3.6.1.4.1.5205.2.111.1.9.1 |
prvtCESModuleIdAn integer uniquely identifying slot of the CES module installed Integer32 .1.3.6.1.4.1.5205.2.111.1.9.1.1 |
prvtCESFirmwareImageNameName of the firmware image filerw OCTET STRING .1.3.6.1.4.1.5205.2.111.1.9.1.2 |
prvtCESUpdateActionUpdate CES firmwarerw Enumeration .1.3.6.1.4.1.5205.2.111.1.9.1.3 |
prvtCESUpdateStatusThe status of the last update procedure, if any. This
object will have a value of updateStatusUnknown(2) if no
update process has been performed.ro Enumeration .1.3.6.1.4.1.5205.2.111.1.9.1.4 |
prvtCESTFTPServerIP Address of Tftp Serverrw IpAddress .1.3.6.1.4.1.5205.2.111.1.9.1.5 |
prvtCESConformance OBJECT IDENTIFIER .1.3.6.1.4.1.5205.2.111.2 |
prvtCESDsx1Compliances OBJECT IDENTIFIER .1.3.6.1.4.1.5205.2.111.2.1 |
prvtCESDsx1Groups OBJECT IDENTIFIER .1.3.6.1.4.1.5205.2.111.2.2 |