PANDATEL-BMP-MODEM-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for PANDATEL-BMP-MODEM-MIB.
17
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
17 total| Object Name |
|---|
bmp OBJECT IDENTIFIER .1.3.6.1.4.1.760.1.1.2.1.10.301 |
bmpModemTableThis table contains information about all BM-P modems in all racks. SEQUENCE OF BmpTableEntry .1.3.6.1.4.1.760.1.1.2.1.10.301.1 |
bmpTableEntryThe index of the table. BmpTableEntry .1.3.6.1.4.1.760.1.1.2.1.10.301.1.1 |
mdmRackThe index of the rack where the modem is installed.ro INTEGER .1.3.6.1.4.1.760.1.1.2.1.10.301.1.1.1 |
mdmModemThis variable displays the slot number where the
corresponding modem is installed in the rack.ro INTEGER .1.3.6.1.4.1.760.1.1.2.1.10.301.1.1.2 |
mdmPositionThis variable displays the location of the corresponding
modem: 'local' or 'remote'. The modem which is plugged
into a managed rack is 'local', the counterpart is 'remote'.ro Enumeration .1.3.6.1.4.1.760.1.1.2.1.10.301.1.1.3 |
mdmModemNameThe verbal name of this modem.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.760.1.1.2.1.10.301.1.1.5 |
mdmDataEquipmentEmulationInterface mode of the unit: 'dte' or 'dce', 'te' or 'nt'.ro Enumeration .1.3.6.1.4.1.760.1.1.2.1.10.301.1.1.6 |
mdmClockModeThe clock mode of the unit: 'master' or 'slave'.rw Enumeration .1.3.6.1.4.1.760.1.1.2.1.10.301.1.1.20 |
mdmDistanceThe transmission distance of the unit: 'long' or 'short'.
'Long' is valid for link data rates of up to 64 Kbps. For
data rates higher than 64 Kbps this entry must be set to
'short'.rw Enumeration .1.3.6.1.4.1.760.1.1.2.1.10.301.1.1.21 |
mdmDataRateAdaptationThis entry enables or disables data rate adaptation, i.e. one
unit operates at line speed and the other one at lower speeds
(1.2, 2.4, 4.8 or 9.6 Kbps at 64 Kbps line speed and 1.2, 2.4,
4.8, 9.6 or 19.2 Kbps at 128 Kbps line speed).rw Enumeration .1.3.6.1.4.1.760.1.1.2.1.10.301.1.1.22 |
mdmClockSourceThe clock source of the link: 'internal', 'external', or
'async'.rw Enumeration .1.3.6.1.4.1.760.1.1.2.1.10.301.1.1.24 |
mdmDataRateThe data rate at the interface in bits per seconds. If
dataRateAdaptation is disabled, the data rate at the remote
counterpart changes simultaneously. Otherwise the data rate
at one unit is fixed to line speed and the data rate at the
other unit must be set to speeds lower than line speed.rw Enumeration .1.3.6.1.4.1.760.1.1.2.1.10.301.1.1.25 |
mdmLocalCarrierDetect1The data carrier detect mode at the interface: if set to
'fo-link-and-remote-handshake' the DCD signal (resp. I for
X.21, etc.) follows link status and remote RTS (resp. C for
X.21, etc.), if set to 'fo-link' the DCD signal follows link
status only.rw Enumeration .1.3.6.1.4.1.760.1.1.2.1.10.301.1.1.60 |
mdmLocalCarrierDetect2The data carrier detect mode 2 at the interface: if set to
'fo-link-and-remote-handshake' the DSR signal follows link
status and remote RTS (resp. C for X.21, etc.), if set to
'fo-link' the DSR signal follows link status only.rw Enumeration .1.3.6.1.4.1.760.1.1.2.1.10.301.1.1.61 |
bmp-modem OBJECT IDENTIFIER .1.3.6.1.4.1.760.1.1.2.1.10.10000.2.301 |
RFC1213-MIB Unknown .1.3.6.1.4.1.760.1.1.2.1.10.10000.2.301 |