MWR-ETHERNET-MIB
This specifies the contact information and the revision tracking information for the MIB module version.
Main OID:
mwrModIdentity.1.3.6.1.4.1.7262.4.5.1000
613
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
613 total| Object Name |
|---|
mwrPlatformObjId OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.1 |
mwrEbandObjId OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.1.1 |
mwrEnhancedObjId OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.1.2 |
mwrSystem OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.2 |
mwrSystemConfigurations OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.2.1 |
mwrSystemTypeAvailable system types for single carrier and multi carriers systems are: onePlusZero1cr - 1+0 single carrier onePlusZero2cr - 1+0 dual carriers onePlusZero2crXpic - 1+0 dual carriers XPICrw Enumeration .1.3.6.1.4.1.7262.4.5.2.1.1 |
mwrPacketSwitchModeIn bridge mode the system is always inband managed on any of the user ports. However in port-isolation mode, the system can be managed outOfBand or inband on a specific port.rw Enumeration .1.3.6.1.4.1.7262.4.5.2.1.2 |
mwrSysSpeed OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.2.1.3 |
mwrSystemCurrentSpeedChanges the working speed of the system.rw Integer32 .1.3.6.1.4.1.7262.4.5.2.1.3.1 |
mwrSystemStatus OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.2.2 |
mwrSystemOperStatusThe current operational state of the system.ro Enumeration .1.3.6.1.4.1.7262.4.5.2.2.1 |
mwrSystemFaultSeverityThe current state of the most serious system alarm severity. If system is running diagnostics, the status will be test.ro Enumeration .1.3.6.1.4.1.7262.4.5.2.2.2 |
mwrSystemTemperatureThe current system temperature.ro Integer32 .1.3.6.1.4.1.7262.4.5.2.2.3 |
mwrPlatformTypeIdentifies the system platform type. The possible system types are: - eband - enhanced - enhanced-mcro Enumeration .1.3.6.1.4.1.7262.4.5.2.2.4 |
mwrPacketSwitchModeStatusThis object indicates the running configuration for the packet switch mode.ro Enumeration .1.3.6.1.4.1.7262.4.5.2.2.5 |
mwrSystemTypeStatusThis object indicates the running configuration for the system type status.ro Enumeration .1.3.6.1.4.1.7262.4.5.2.2.6 |
mwrSystemCommands OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.2.3 |
mwrResetSystemWriting '1' to this object resets the system.rw Enumeration .1.3.6.1.4.1.7262.4.5.2.3.1 |
mwrSaveConfigWriting '1' or 'save' to this object saves running configuration of the system.rw Enumeration .1.3.6.1.4.1.7262.4.5.2.3.2 |
mwrDeleteConfigUsing this object, either the startup config or the switch config can be deleted. Deleting startup config removes all system configuration for next system restart. Deleting switch config only clears the switch configuration.rw Enumeration .1.3.6.1.4.1.7262.4.5.2.3.3 |
mwrSystemInventory OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.2.4 |
mwrHwInventory OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.2.4.1 |
mwrMacAddressThe MAC Address of the system.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.2.4.1.1 |
mwrTargetCfgFilePartNumberA textual string containing part number of the target configuration file.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.2.4.1.2 |
mwrUnitSerialNoA textual string containing Serial Number of the Unit.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.2.4.1.3 |
mwrUnitAssemblyNoA textual string containing the Assembly Number of the Unit.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.2.4.1.4 |
mwrBasebandSerialNoA textual string containing Serial no of the baseband.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.2.4.1.5 |
mwrBasebandAssemblyNoA textual string containing assembly no of the baseband.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.2.4.1.6 |
mwrPsuSerialNoA textual string containing Serial no of the PSU.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.2.4.1.7 |
mwrPsuAssemblyNoA textual string containing assembly no of the PSU.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.2.4.1.8 |
mwrRfSerialNoA textual string containing Serial no of the RF.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.2.4.1.9 |
mwrRfAssemblyNoA textual string containing assembly no of the RF.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.2.4.1.10 |
mwrRfRevisionNoA textual string containing revision no of the RF.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.2.4.1.11 |
mwrDiplexerSerialNoA textual string containing Serial no of the Diplexer.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.2.4.1.12 |
mwrDiplexerAssemblyNoA textual string containing assembly no of the Diplexer.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.2.4.1.13 |
mwrSystemCleiNoA textual string containing system CLEI code.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.2.4.1.14 |
mwrSwInventory OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.2.4.2 |
mwrSwInventoryTableTable containing the software inventory. SEQUENCE OF MwrSwInventoryEntry .1.3.6.1.4.1.7262.4.5.2.4.2.1 |
mwrSwInventoryEntrySoftware inventory entry. MwrSwInventoryEntry .1.3.6.1.4.1.7262.4.5.2.4.2.1.1 |
mwrSwInvBankSoftware bank in the flash. Enumeration .1.3.6.1.4.1.7262.4.5.2.4.2.1.1.1 |
mwrSwInvStatusSoftware bank status.ro Enumeration .1.3.6.1.4.1.7262.4.5.2.4.2.1.1.2 |
mwrSwInvOmniReleaseThe version number of the Omni.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.2.4.2.1.1.3 |
mwrSwInvTargetConfFileVersionThe version number of the target configuration file.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.2.4.2.1.1.4 |
mwrSwInvMibVersionThe version number of the system MIB.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.2.4.2.1.1.5 |
mwrSwInvSecurityVersionThe version number of the security package.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.2.4.2.1.1.6 |
mwrSystemNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.2.5 |
mwrSysTcfInvalidThis notification is raised when The HW specific factory defined information (TCF) in the system is not valid. NOTIFICATION-TYPE .1.3.6.1.4.1.7262.4.5.2.5.1 |
mwrSysTempOutOfLimitThis notification is raised when the system temperature is out of limits. NOTIFICATION-TYPE .1.3.6.1.4.1.7262.4.5.2.5.2 |
mwrSoftware OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.3 |
mwrSoftwareConfigurations OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.3.1 |
mwrSoftwareStatus OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.3.2 |
mwrSwBackupBankStatusThis object represents the status of the backup bank.ro Enumeration .1.3.6.1.4.1.7262.4.5.3.2.1 |
mwrSoftwareCommands OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.3.3 |
mwrSwCommitWriting '1' to this object commits all the active bank settings to the backup bank.rw Enumeration .1.3.6.1.4.1.7262.4.5.3.3.1 |
mwrSwSwitchBanksThis objects switches bank to the specified bank. Next time the system resets, it loads up from that bank.rw Enumeration .1.3.6.1.4.1.7262.4.5.3.3.2 |
mwrSoftwareNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.3.4 |
mwrLicensing OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.4 |
mwrLicensingConfigurations OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.4.1 |
mwrLicenseUpgradeKeyThe 33 Bytes licensing key used for upgrading features/capacity. Reading this object always returns an empty string.rw OCTET STRING .1.3.6.1.4.1.7262.4.5.4.1.1 |
mwrLicensingStatus OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.4.2 |
mwrLicenseCountThis object indicates the number of times the system has been upgraded/downgraded with features/capacity.ro Integer32 .1.3.6.1.4.1.7262.4.5.4.2.1 |
mwrLicensedSpeedThis object indicates the system licensed speed.ro Integer32 .1.3.6.1.4.1.7262.4.5.4.2.2 |
mwrLicenseFeaturesTableA table containing supported system licensed features. SEQUENCE OF MwrLicenseFeaturesEntry .1.3.6.1.4.1.7262.4.5.4.2.3 |
mwrLicenseFeaturesEntryA table entry containing supported system licensed features. MwrLicenseFeaturesEntry .1.3.6.1.4.1.7262.4.5.4.2.3.1 |
mwrLicenseFeatureIndexThis object indicates the list of system features. Integer32 .1.3.6.1.4.1.7262.4.5.4.2.3.1.1 |
mwrLicenseFeatureId2 ACM (includes WMA where applicable) (LF2) 3 Ethernet UNI (ELINE/ELAN MEF service) (LF3) 4 Packet Fragmentation (LF4) 5 Secured Access (LF5) 6 Ethernet OAM (802.1ag, 802.3ah, Y.1731) (LF6) 7 Advanced Performance Monitoring (LF7) 11 Bandwidth Accelerator (LF11) 13 Header Compression (LF13)ro Integer32 .1.3.6.1.4.1.7262.4.5.4.2.3.1.2 |
mwrLicenseFeatureThe name of the feature.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.4.2.3.1.3 |
mwrLicenseFeatureStatusSpecifies whether the feature is unlicensed or licensed.ro Enumeration .1.3.6.1.4.1.7262.4.5.4.2.3.1.4 |
mwrSyncE OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.5 |
mwrSyncEConfigurations OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.5.1 |
mwrSyncEStateIn manual mode, SyncE source will use primary clock source and when the primary source has loss of lock, the SyncE goes into holdover. The primary source will be used again after the system regains the lock on primary source. In auto mode, if the current clock source goes out of lock, the recovered clock from the other source will be used.rw Enumeration .1.3.6.1.4.1.7262.4.5.5.1.1 |
mwrSyncEPrimarySourceSelects which port to be used as SyncE master clock source.rw Enumeration .1.3.6.1.4.1.7262.4.5.5.1.2 |
mwrSyncESecondarySourceSelects which port to be used as SyncE clock source when the master SyncE clock source is not available.rw Enumeration .1.3.6.1.4.1.7262.4.5.5.1.3 |
mwrSyncEMemberPortsEnter a string indicating all SyncE member ports. Example: gi01 gi04 Port options: gi01 gi02 gi03 gi04 radiorw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.5.1.4 |
mwrSyncEForcedHoldoverThis forces SyncE into holdover mode. After the configurable timeout value, the forced holdover will be taken out. The forced timeout can be 0 to 300sec, where 0 means infinite and default is 30sec. An example of the format of the string is as follows: 'on 20' or 'off'. The second parameter indicates the holdover time in sec. The single quote marks i.e. ' ' are not used in the command.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.5.1.5 |
mwrSyncERevertiveIn revertive mode, if the current source is secondary and the primary is Ok for configured amount of time, the primary will be used. The default revertive time is 10sec. An example of the format of the string is as follows: 'on 20' or 'off'. The second parameter when revertive is turned on is the time in sec. The single quote marks i.e. ' ' are not used in the command.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.5.1.6 |
mwrSyncEWanderFilterITU G.8262 specifies different wander filter requirements for networks based on the 2.048 kbit/s hierarchy , option1, vs those based on the 1.544kbit/s hierarchy, option2. Option 2 specifies a low pass filter bandwidth of 0.1Hz, while option1 specifies a bandwidth between 1 and 10 Hz.rw Enumeration .1.3.6.1.4.1.7262.4.5.5.1.7 |
mwrSyncEStatus OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.5.2 |
mwrSyncEClockSourceRetrieves SyncE clock source currently in use.ro Enumeration .1.3.6.1.4.1.7262.4.5.5.2.1 |
mwrSyncEAcquisitionStatusRetrieves SyncE acquisition status.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.5.2.2 |
mwrSyncENotifications OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.5.3 |
mwrSynceLostLockThis notification is raised when system has lost synchronization to syncE clock source. NOTIFICATION-TYPE .1.3.6.1.4.1.7262.4.5.5.3.1 |
mwrSynceSecondarySourceInUseThis notification is raised whens ystem has lost synchronization to primary syncE clock source, and now synchronized to secondary source. NOTIFICATION-TYPE .1.3.6.1.4.1.7262.4.5.5.3.2 |
mwrSynceConfigMismatchThis notification is raised when the configuration of syncE between the peers in the radio link is mismatched. NOTIFICATION-TYPE .1.3.6.1.4.1.7262.4.5.5.3.3 |
mwrTiming OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.6 |
mwrTimingConfigurations OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.6.1 |
mwrDateTimeThe system date and time.rw DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.6.1.1 |
mwrSntpEnableIndicates whether SNTP feature is enabled.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.6.1.2 |
mwrSntpOffsetSystem time offset from GMT in tenths of hours. For example, an offset of 10 indicates 10 tenths, or 1 hour. An offset of 5 indicates half an hour.rw Integer32 (-140..140) .1.3.6.1.4.1.7262.4.5.6.1.3 |
mwrSntpServerTableTable containing SNTP server entries SEQUENCE OF MwrSntpServerEntry .1.3.6.1.4.1.7262.4.5.6.1.4 |
mwrSntpServerEntryContains the SNTP server information MwrSntpServerEntry .1.3.6.1.4.1.7262.4.5.6.1.4.1 |
mwrSntpServerIndexA unique value for each server. Integer32 .1.3.6.1.4.1.7262.4.5.6.1.4.1.1 |
mwrSntpServerDomainIndicates SNTP server inet address type. Valid types are ipv4 or ipv6.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.7262.4.5.6.1.4.1.2 |
mwrSntpServerAddressIndicates SNTP server inet address octet string.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.7262.4.5.6.1.4.1.3 |
mwrSntpServerStatusThe status of the SNTP server.ro Enumeration .1.3.6.1.4.1.7262.4.5.6.1.4.1.4 |
mwrSntpServerStratumSpecifies the stratum of a server, 0 for failed serverro Integer32 .1.3.6.1.4.1.7262.4.5.6.1.4.1.5 |
mwrTimingStatus OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.6.2 |
mwrTimingLastDateTimeChangedDate and Time for the last system time adjustment.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.6.2.1 |
mwrTimingLastTimeAdjustmentLast system time adjustment in hundredths of seconds.ro Integer32 .1.3.6.1.4.1.7262.4.5.6.2.2 |
mwrTimingCummulativeTimeChangeCumulative system time adjustment in hundredths of seconds.ro Integer32 .1.3.6.1.4.1.7262.4.5.6.2.3 |
mwrTimingCommands OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.6.3 |
mwrSntpRestoreDefaultRestores SNTP servers to default Addresses.rw Enumeration .1.3.6.1.4.1.7262.4.5.6.3.1 |
mwrTimingNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.6.4 |
mwrSntpServerUnreachableThis notification is raised when one or more of the configured SNTP server is not reachable by the system. NOTIFICATION-TYPE .1.3.6.1.4.1.7262.4.5.6.4.1 |
mwrSystemTimeCorrectedThis notification is raised change in system time is detected, and system time is adjusted NOTIFICATION-TYPE .1.3.6.1.4.1.7262.4.5.6.4.2 |
mwrAAA OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.7 |
mwrAAAConfigurations OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.7.1 |
mwrAAAUserAuthenticationThis object configures the user authentication method.rw Enumeration .1.3.6.1.4.1.7262.4.5.7.1.1 |
mwrRadiusConfigurations OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.7.1.2 |
mwrRadiusAdminUserStrictIf strict mode is off, the admin user can login when radius is turned off or unreachable. When strict mode is on, admin user will only be authenticated against the radius server.rw Enumeration .1.3.6.1.4.1.7262.4.5.7.1.2.1 |
mwrRadiusServerTimeOutTimeout period for authentication requestsrw Integer32 .1.3.6.1.4.1.7262.4.5.7.1.2.2 |
mwrRadiusServerDeadTimeTime to declare an unresponsive server 'dead'rw Integer32 .1.3.6.1.4.1.7262.4.5.7.1.2.3 |
mwrRadiusServerReTransmitMaximum number of retransmits to an unresponsive serverrw Integer32 .1.3.6.1.4.1.7262.4.5.7.1.2.4 |
mwrRadiusServerTableTable containing radius server entries SEQUENCE OF MwrRadiusServerEntry .1.3.6.1.4.1.7262.4.5.7.1.2.5 |
mwrRadiusServerEntryContains the SNTP server information MwrRadiusServerEntry .1.3.6.1.4.1.7262.4.5.7.1.2.5.1 |
mwrRadiusServerIndexA unique value for each radius server. Integer32 .1.3.6.1.4.1.7262.4.5.7.1.2.5.1.1 |
mwrRadiusCfgdHostDomainIndicates configured radius inet address type. Valid types are ipv4 or ipv6.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.7262.4.5.7.1.2.5.1.2 |
mwrRadiusCfgdHostAddressIndicates configured radius server inet address octet string.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.7262.4.5.7.1.2.5.1.3 |
mwrRadiusCfgdHostKeyThe key of the configured radius server.rw DisplayString .1.3.6.1.4.1.7262.4.5.7.1.2.5.1.4 |
mwrNetworking OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.8 |
mwrNetworkingConfigurations OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.8.1 |
mwrNetMgmtPriority OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.8.1.1 |
mwrNetMgmtVlanPriorityThe object configures the VLAN priority(0...7)rw Integer32 .1.3.6.1.4.1.7262.4.5.8.1.1.1 |
mwrNetMgmtDscpThe Differentiated Services Code Point (DSCP) of IP traffic generated by the system (0...63)rw Integer32 .1.3.6.1.4.1.7262.4.5.8.1.1.2 |
mwrNetMgmtIpv4 OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.8.1.2 |
mwrIpv4TableA table containing the IPv4 information. SEQUENCE OF MwrIpv4Entry .1.3.6.1.4.1.7262.4.5.8.1.2.1 |
mwrIpv4EntryA table entry containing the IPv4 information. MwrIpv4Entry .1.3.6.1.4.1.7262.4.5.8.1.2.1.1 |
mwrIpv4IndexThe IPv4 table index. There is only one entry in this table and can not be deleted. Integer32 (1) .1.3.6.1.4.1.7262.4.5.8.1.2.1.1.1 |
mwrIpv4AddressThe IPv4 address of the system.rw IpAddress .1.3.6.1.4.1.7262.4.5.8.1.2.1.1.2 |
mwrIpv4SubnetMaskThe IPv4 subnet mask of the system.rw IpAddress .1.3.6.1.4.1.7262.4.5.8.1.2.1.1.3 |
mwrIpv4DefaultGatewayThe IPv4 default gateway of the system.rw IpAddress .1.3.6.1.4.1.7262.4.5.8.1.2.1.1.4 |
mwrIpv4RowStatusThis object is used for applying ipv4 configuration attributes simultaneously.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.8.1.2.1.1.5 |
mwrSecondaryGatewayThe IPv4 secondary gateway of the system.rw IpAddress .1.3.6.1.4.1.7262.4.5.8.1.2.2 |
mwrNetMgmttIpv6 OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.8.1.3 |
mwrIpv6TableA table containing the IPv6 information. SEQUENCE OF MwrIpv6Entry .1.3.6.1.4.1.7262.4.5.8.1.3.1 |
mwrIpv6EntryA table entry containing the IPv6 information. MwrIpv6Entry .1.3.6.1.4.1.7262.4.5.8.1.3.1.1 |
mwrIpv6IndexThe IPv6 table index. There is only one entry in this table and can not be deleted. Integer32 (1) .1.3.6.1.4.1.7262.4.5.8.1.3.1.1.1 |
mwrIpv6DomainIndicates ipv6 inet address type.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.7262.4.5.8.1.3.1.1.2 |
mwrIpv6AddressIndicates IPv6 inet address octet string.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.7262.4.5.8.1.3.1.1.3 |
mwrIpv6PrefixIndicates ipv6 prefix.rw Integer32 .1.3.6.1.4.1.7262.4.5.8.1.3.1.1.4 |
mwrIpv6GatewayDomainIndicates IPv6 gateway inet address type. This will always return IPv6 inet address type.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.7262.4.5.8.1.3.1.1.5 |
mwrIpv6GatewayAddressIndicates IPv6 gateway inet address octet string.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.7262.4.5.8.1.3.1.1.6 |
mwrIpv6RowStatusThis object is used for applying IPv6 configuration attributes simultaneously.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.8.1.3.1.1.7 |
mwrSecondaryIpv6GatewayDomainThis object will return the secondary IPv6 gateway inet address type.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.7262.4.5.8.1.3.2 |
mwrSecondaryIpv6GatewayAddressThis object will return the secondary IPv6 gateway inet address.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.7262.4.5.8.1.3.3 |
mwrUserInterfaceMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.8.1.4 |
mwrTelnetEnableIndicates whether telnet access is allowed.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.8.1.4.1 |
mwrSshEnableIndicates whether ssh access is allowed. This configuration only applies to security mode.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.8.1.4.2 |
mwrHttpEnableIndicates whether http is enabled.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.8.1.4.3 |
mwrHttpsEnableIndicates whether secured http access is allowed. This configuration only applies to security mode.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.8.1.4.4 |
mwrSnmpv1v2cEnableIndicates whether SNMP v1/v2c is allowed in security mode. This configuration only applies to security mode.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.8.1.4.5 |
mwrFtpEnableThis object allows enabling or disabling ftp when in secure mode. By default ftp is enabled.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.8.1.4.6 |
mwrFileTransfer OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.8.1.5 |
mwrFileXfrDirectionThe behavior of the FTP/SFTP machine: 1 - ServerMode 2 - ClientMode 3 - both Server and Client available Mwr 1.0 just supports Client Mode.rw Enumeration .1.3.6.1.4.1.7262.4.5.8.1.5.1 |
mwrFileXfrTableTable containing the FTP client parameters. SEQUENCE OF MwrFileXfrEntry .1.3.6.1.4.1.7262.4.5.8.1.5.2 |
mwrFileXfrEntryTable entry containing the FTP client parameters. MwrFileXfrEntry .1.3.6.1.4.1.7262.4.5.8.1.5.2.1 |
mwrFileXfrSeqIDFor the same manager, the possibility to define different FTP/SFTP transfer actions. Integer32 .1.3.6.1.4.1.7262.4.5.8.1.5.2.1.1 |
mwrFileXfrIdentifierThe identifier of the type of file to be imported/exported.rw Enumeration .1.3.6.1.4.1.7262.4.5.8.1.5.2.1.2 |
mwrFileXfrNameThe Name of the file to be imported/exported.rw DisplayString .1.3.6.1.4.1.7262.4.5.8.1.5.2.1.3 |
mwrFileXfrModeThe file transfer mode specifying either a ftp or sftp request. The sftp mode is only supported when security is licensed/installed.rw Enumeration .1.3.6.1.4.1.7262.4.5.8.1.5.2.1.4 |
mwrFileXfrServerDomainThe server domain such as IPv4 or IPv6 type.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.7262.4.5.8.1.5.2.1.5 |
mwrFileXfrServerAddressThe server IP address in InetAddress format which could be an IPv4 or IPv6 address.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.7262.4.5.8.1.5.2.1.6 |
mwrFileXfrClientDirectionThe behavior of the FTP or SFTP Client: 1 - import, i.e. download data file 2 - export, i.e. upload data file. The only supported option for omni and tcf is import since these files are used only in upgrade case. Also the supported option for pm, eventlog and perfLog is export option. The rest can be imported or exported.rw Enumeration .1.3.6.1.4.1.7262.4.5.8.1.5.2.1.7 |
mwrFileXfrUserNameFTP or SFTP User Name when Client Mode is selected.rw DisplayString .1.3.6.1.4.1.7262.4.5.8.1.5.2.1.8 |
mwrFileXfrPasswordFTP or SFTP password when Client Mode is selected. For get operation - the returned value will be zero length string.rw DisplayString .1.3.6.1.4.1.7262.4.5.8.1.5.2.1.9 |
mwrFileXfrNumEntriesThis object is used to indicate the number of entries for the performance log to be transferred. If it's set to zero, it will transfer the entire file.rw Integer32 .1.3.6.1.4.1.7262.4.5.8.1.5.2.1.10 |
mwrFileXfrStatusThis object contains the current status of the last requested import/export of the corresponding row component.ro Enumeration .1.3.6.1.4.1.7262.4.5.8.1.5.2.1.11 |
mwrFileXfrRowStatusThe row status variable, used according to: - Manager can create a row using the createAndWait. - Once created, the row is put into notInService by Agent. - On Manager request, row status can be set to active one at a time. This means that the Client has to start the file transfer. - Row data, such as the FileServerAddress, User Name or Password can be changed once the row has been created, but only if this field is set to notInService. All other fields can not be set once the row is created, but the row must be removed and created again. - Manager can use destroy to remove the row.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.8.1.5.2.1.12 |
mwrNetMgmtInterfaceTableTable containing the network management interface configurations. SEQUENCE OF MwrNetMgmtInterfaceEntry .1.3.6.1.4.1.7262.4.5.8.1.6 |
mwrNetMgmtInterfaceEntryEntry for the network management interface table. MwrNetMgmtInterfaceEntry .1.3.6.1.4.1.7262.4.5.8.1.6.1 |
mwrNetMgmtInterfaceIndexThis object is an index to network management interface table. There will always be one entry in this table. Integer32 .1.3.6.1.4.1.7262.4.5.8.1.6.1.1 |
mwrNetMgmtVlanIdIndicates the VLAN Id (1...4090)rw Integer32 .1.3.6.1.4.1.7262.4.5.8.1.6.1.2 |
mwrNetMgmtInterface1When this object is enabled the gi0/1 port will be configured as a management port. Also the corresponding mode (inband/outOfBand) should be set as well.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.8.1.6.1.3 |
mwrNetMgmtInterface1ModeThis object indicates whether the gi0/1 management interface is inband or outOfBand. This applies only when the packet switch mode is configured in port isolation mode. In Bridge mode setup, this will always be inband.rw Enumeration .1.3.6.1.4.1.7262.4.5.8.1.6.1.4 |
mwrNetMgmtInterface1TaggedThis object indicates whether the system will be managed with vlan tagged management traffic or not.rw Enumeration .1.3.6.1.4.1.7262.4.5.8.1.6.1.5 |
mwrNetMgmtInterface2When this object is enabled the gi0/2 port will be configured as a management port. Also the corresponding mode (inband/outOfBand) should be set as well.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.8.1.6.1.6 |
mwrNetMgmtInterface2ModeThis object indicates whether the gi0/2 management interface is inband or outOfBand. This applies only when the packet switch mode is configured in port isolation mode. In Bridge mode setup, this will always be inband.rw Enumeration .1.3.6.1.4.1.7262.4.5.8.1.6.1.7 |
mwrNetMgmtInterface2TaggedThis object indicates whether the system will be managed with vlan tagged management traffic or not.rw Enumeration .1.3.6.1.4.1.7262.4.5.8.1.6.1.8 |
mwrNetMgmtInterface3When this object is enabled the gi0/3 port will be configured as a management port. Also the corresponding mode (inband/outOfBand) should be set as well.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.8.1.6.1.9 |
mwrNetMgmtInterface3ModeThis object indicates whether the gi0/3 management interface is inband or outOfBand. This applies only when the packet switch mode is configured in port isolation mode. In Bridge mode setup, this will always be inband.rw Enumeration .1.3.6.1.4.1.7262.4.5.8.1.6.1.10 |
mwrNetMgmtInterface3TaggedThis object indicates whether the system will be managed with vlan tagged management traffic or not.rw Enumeration .1.3.6.1.4.1.7262.4.5.8.1.6.1.11 |
mwrNetMgmtInterface4When this object is enabled the gi0/4 port will be configured as a management port. Also the corresponding mode (inband/outOfBand) should be set as well.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.8.1.6.1.12 |
mwrNetMgmtInterface4ModeThis object indicates whether the gi0/4 management interface is inband or outOfBand. This applies only when the packet switch mode is configured in port isolation mode. In Bridge mode setup, this will always be inband.rw Enumeration .1.3.6.1.4.1.7262.4.5.8.1.6.1.13 |
mwrNetMgmtInterface4TaggedThis object indicates whether the system will be managed with vlan tagged management traffic or not.rw Enumeration .1.3.6.1.4.1.7262.4.5.8.1.6.1.14 |
mwrNetMgmtInterfaceRowStatusThis object is used for applying all management interface configuration in an atomic operation.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.8.1.6.1.15 |
mwrNetworkingStatus OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.8.2 |
mwrMaintenanceIpv4 OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.8.2.1 |
mwrMaintenanceIpv4AddressThis object indicates the maintenance IPv4 address.ro IpAddress .1.3.6.1.4.1.7262.4.5.8.2.1.1 |
mwrMaintenanceSubnetMaskThis object indicates the maintenance IPv4 subnet mask.ro IpAddress .1.3.6.1.4.1.7262.4.5.8.2.1.2 |
mwrActiveIpv4GatewayThis object indicates the active IPv4 gateway.ro IpAddress .1.3.6.1.4.1.7262.4.5.8.2.1.3 |
mwrMaintenanceIpv6 OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.8.2.2 |
mwrIpv6LinkLocalIPrefixThis object indicates the IPv6 link local prefix.ro Integer32 .1.3.6.1.4.1.7262.4.5.8.2.2.1 |
mwrIpv6LinkLocalAddressIndicates ipv6 link local inet address octet string.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.7262.4.5.8.2.2.2 |
mwrActiveIpv6GatewayThis object indicates the active IPv6 gateway.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.7262.4.5.8.2.2.3 |
mwrPeerNetworkingStatus OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.8.3 |
mwrPeerMacAddressThe MAC Address of the peer.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.8.3.1 |
mwrPeerIpv4AddressThe peer IPv4 Address.ro IpAddress .1.3.6.1.4.1.7262.4.5.8.3.2 |
mwrPeerIpv4SubnetMaskThe peer IPv4 subnet mask.ro IpAddress .1.3.6.1.4.1.7262.4.5.8.3.3 |
mwrPeerIpv4DefaultGatewayThe peer IPv4 default gateway.ro IpAddress .1.3.6.1.4.1.7262.4.5.8.3.4 |
mwrPeerIpv6PrefixThe peer IPv6 prefix.ro Integer32 .1.3.6.1.4.1.7262.4.5.8.3.5 |
mwrPeerIpv6DomainThe peer IPv6 domain.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.7262.4.5.8.3.6 |
mwrPeerIpv6AddressThe peer IPv6 address.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.7262.4.5.8.3.7 |
mwrPeerIpv6GatewayDomainThe peer IPv6 gateway domainro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.7262.4.5.8.3.8 |
mwrPeerIpv6GatewayAddressThe peer IPv6 gateway address.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.7262.4.5.8.3.9 |
mwrPeerVlanIdThe peer vlan Id.ro Integer32 .1.3.6.1.4.1.7262.4.5.8.3.10 |
mwrPeerVlanPriorityThe peer vlan priority.ro Integer32 .1.3.6.1.4.1.7262.4.5.8.3.11 |
mwrPeerDscpThe peer management dscp.ro Integer32 .1.3.6.1.4.1.7262.4.5.8.3.12 |
mwrNetworkingNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.8.4 |
mwrEthernet OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.9 |
mwrEthernetConfigurations OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.9.1 |
mwrQos OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.9.1.1 |
mwrQosStateIndicates whether QOS is enabled.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.9.1.1.1 |
mwrCosSourceIndicates the class of service tag type. Based on the setting system will use the CoS value in the outer VLAN tag, inner VLAN tag, DSCP or MPLS exp.rw Enumeration .1.3.6.1.4.1.7262.4.5.9.1.1.2 |
mwrOuterTpidSets the value of the Q-in-Q outer tag. This tag is also used to classify the single tagged traffic. Default value is 0x8100.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.9.1.1.3 |
mwrInnerTpidSets the value of the Q-in-Q inner VLAN tag. Default value is 0x8100.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.9.1.1.4 |
mwrCosTableA table of Qos Settings per port, the configuration corresponds to the egress QoS of radio port. SEQUENCE OF MwrCosEntry .1.3.6.1.4.1.7262.4.5.9.1.1.5 |
mwrCosEntryAn entry of Qos setting per port MwrCosEntry .1.3.6.1.4.1.7262.4.5.9.1.1.5.1 |
mwrCosIndexA unique name identifying each enet port in port isolation mode or the bridgeMode index when system is configured in bridge mode. Enumeration .1.3.6.1.4.1.7262.4.5.9.1.1.5.1.1 |
mwrCos0User queue assignments for CoS0. There are 8 CoS queues. Their corresponding queue numbers are 1 to 8 where 1 is the lowest priority queue and 8 is the highest priority queue.rw QueueType .1.3.6.1.4.1.7262.4.5.9.1.1.5.1.2 |
mwrCos1User queue assignments for CoS1. There are 8 CoS queues. Their corresponding queue numbers are 1 to 8 where 1 is the lowest priority queue and 8 is the highest priority queue.rw QueueType .1.3.6.1.4.1.7262.4.5.9.1.1.5.1.3 |
mwrCos2User queue assignments for CoS2. There are 8 CoS queues. Their corresponding queue numbers are 1 to 8 where 1 is the lowest priority queue and 8 is the highest priority queue.rw QueueType .1.3.6.1.4.1.7262.4.5.9.1.1.5.1.4 |
mwrCos3User queue assignments for CoS3. There are 8 CoS queues. Their corresponding queue numbers are 1 to 8 where 1 is the lowest priority queue and 8 is the highest priority queue.rw QueueType .1.3.6.1.4.1.7262.4.5.9.1.1.5.1.5 |
mwrCos4User queue assignments for CoS4. There are 8 CoS queues. Their corresponding queue numbers are 1 to 8 where 1 is the lowest priority queue and 8 is the highest priority queue.rw QueueType .1.3.6.1.4.1.7262.4.5.9.1.1.5.1.6 |
mwrCos5User queue assignments for CoS5. There are 8 CoS queues. Their corresponding queue numbers are 1 to 8 where 1 is the lowest priority queue and 8 is the highest priority queue.rw QueueType .1.3.6.1.4.1.7262.4.5.9.1.1.5.1.7 |
mwrCos6User queue assignments for CoS6. There are 8 CoS queues. Their corresponding queue numbers are 1 to 8 where 1 is the lowest priority queue and 8 is the highest priority queue.rw QueueType .1.3.6.1.4.1.7262.4.5.9.1.1.5.1.8 |
mwrCos7User queue assignments for CoS7. There are 8 CoS queues. Their corresponding queue numbers are 1 to 8 where 1 is the lowest priority queue and 8 is the highest priority queue.rw QueueType .1.3.6.1.4.1.7262.4.5.9.1.1.5.1.9 |
mwrCosRowStatusRow status for CoS queue mapping. This object is used to apply all CoS settings simultaneously.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.9.1.1.5.1.10 |
mwrCosDefValueTableA table containing the CoS default value, the configuration corresponds to the egress QoS of radio port. SEQUENCE OF MwrCosDefValueEntry .1.3.6.1.4.1.7262.4.5.9.1.1.6 |
mwrCosDefValueEntryA table entry containing the CoS default value. MwrCosDefValueEntry .1.3.6.1.4.1.7262.4.5.9.1.1.6.1 |
mwrCosDefValueIndexSpecifies CoS default value for each port in port isolation or in bridge mode. Enumeration .1.3.6.1.4.1.7262.4.5.9.1.1.6.1.1 |
mwrCosDefValueSpecifies CoS default value for each port in port isolation or in bridge mode.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.6.1.2 |
mwrCirQTableA table containing the CIR value for each queue, the configuration corresponds to the egress QoS of radio port. SEQUENCE OF MwrCirQEntry .1.3.6.1.4.1.7262.4.5.9.1.1.7 |
mwrCirQEntryA table entry containing the CIR value for each radio queue. MwrCirQEntry .1.3.6.1.4.1.7262.4.5.9.1.1.7.1 |
mwrCirQIndexSpecifies CIR queue index for each radio queue. QueueType .1.3.6.1.4.1.7262.4.5.9.1.1.7.1.1 |
mwrCirQ1User CIR setting for queue 1.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.7.1.2 |
mwrCirQ2User CIR setting for queue 2.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.7.1.3 |
mwrCirQ3User CIR setting for queue 3.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.7.1.4 |
mwrCirQ4User CIR setting for queue 4.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.7.1.5 |
mwrCirQ5User CIR setting for queue 5.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.7.1.6 |
mwrCirQ6User CIR setting for queue 6.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.7.1.7 |
mwrCirQ7User CIR setting for queue 7.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.7.1.8 |
mwrCirQ8User CIR setting for queue 8.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.7.1.9 |
mwrCirQRowStatusThe CIR table Row status. This object is used to apply all queue CIR settings simultaneously.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.9.1.1.7.1.10 |
mwrCbsQTableA table containing CBS settings for each queue, the configuration corresponds to the egress QoS of radio port. SEQUENCE OF MwrCbsQEntry .1.3.6.1.4.1.7262.4.5.9.1.1.8 |
mwrCbsQEntryA table entry containing CBS settings for each queue. MwrCbsQEntry .1.3.6.1.4.1.7262.4.5.9.1.1.8.1 |
mwrCbsQIndexSpecifies CBS queue index for each radio queue. QueueType .1.3.6.1.4.1.7262.4.5.9.1.1.8.1.1 |
mwrCbsQ1User CBS setting for queue 1.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.8.1.2 |
mwrCbsQ2User CBS setting for queue 2.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.8.1.3 |
mwrCbsQ3User CBS setting for queue 3.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.8.1.4 |
mwrCbsQ4User CBS setting for queue 4.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.8.1.5 |
mwrCbsQ5User CBS setting for queue 5.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.8.1.6 |
mwrCbsQ6User CBS setting for queue 6.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.8.1.7 |
mwrCbsQ7User CBS setting for queue 7.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.8.1.8 |
mwrCbsQ8User CBS setting for queue 8.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.8.1.9 |
mwrCbsQRowStatusThe CBS table Row status. This object is used to apply all queue CBS settings simultaneously.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.9.1.1.8.1.10 |
mwrWeightQTableA table containing queue weight setting for each queue, the configuration corresponds to the egress QoS of radio port. SEQUENCE OF MwrWeightQEntry .1.3.6.1.4.1.7262.4.5.9.1.1.9 |
mwrWeightQEntryA table entry containing queue weight setting for each queue. MwrWeightQEntry .1.3.6.1.4.1.7262.4.5.9.1.1.9.1 |
mwrWeightQIndexSpecifies queue weight index for each radio queue. QueueType .1.3.6.1.4.1.7262.4.5.9.1.1.9.1.1 |
mwrWeightQ1Specifies queue weight value for queue 1.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.9.1.2 |
mwrWeightQ2Specifies queue weight value for queue 2.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.9.1.3 |
mwrWeightQ3Specifies queue weight value for queue 3.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.9.1.4 |
mwrWeightQ4Specifies queue weight value for queue 4.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.9.1.5 |
mwrWeightQ5Specifies queue weight value for queue 5.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.9.1.6 |
mwrWeightQ6Specifies queue weight value for queue 6.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.9.1.7 |
mwrWeightQ7Specifies queue weight value for queue 7.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.9.1.8 |
mwrWeightQ8Specifies queue weight value for queue 8.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.9.1.9 |
mwrWeightQRowStatusThe queue weight table Row status. This object is used to apply all queue weight settings simultaneously.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.9.1.1.9.1.10 |
mwrQbsQTableA table containing queue buffer size, the configuration corresponds to the egress QoS of radio port. SEQUENCE OF MwrQbsQEntry .1.3.6.1.4.1.7262.4.5.9.1.1.10 |
mwrQbsQEntryA table entry containing queue buffer size. MwrQbsQEntry .1.3.6.1.4.1.7262.4.5.9.1.1.10.1 |
mwrQbsQIndexSpecifies QBS queue index for each radio queue. QueueType .1.3.6.1.4.1.7262.4.5.9.1.1.10.1.1 |
mwrQbsQ1Specifies queue buffer size (QBS) for queue 1.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.10.1.2 |
mwrQbsQ2Specifies queue buffer size (QBS) for queue 2.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.10.1.3 |
mwrQbsQ3Specifies queue buffer size (QBS) for queue 3.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.10.1.4 |
mwrQbsQ4Specifies queue buffer size (QBS) for queue 4.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.10.1.5 |
mwrQbsQ5Specifies queue buffer size (QBS) for queue 5.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.10.1.6 |
mwrQbsQ6Specifies queue buffer size (QBS) for queue 6.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.10.1.7 |
mwrQbsQ7Specifies queue buffer size (QBS) for queue 7.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.10.1.8 |
mwrQbsQ8Specifies queue buffer size (QBS) for queue 8.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.10.1.9 |
mwrQbsQRowStatusThe queue buffer size (QBS) table Row status. This object is used to apply all queue QBS settings simultaneously.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.9.1.1.10.1.10 |
mwrPolicyQTableA table containing queue policy for each queue, the configuration corresponds to the egress QoS of radio port. SEQUENCE OF MwrPolicyQEntry .1.3.6.1.4.1.7262.4.5.9.1.1.11 |
mwrPolicyQEntryA table entry containing queue policy for each queue. MwrPolicyQEntry .1.3.6.1.4.1.7262.4.5.9.1.1.11.1 |
mwrPolicyQIndexSpecifies queue policy index for each radio queue. QueueType .1.3.6.1.4.1.7262.4.5.9.1.1.11.1.1 |
mwrPolicyQ1User queue policy value for queue 1.rw Enumeration .1.3.6.1.4.1.7262.4.5.9.1.1.11.1.2 |
mwrPolicyQ2User queue policy value for queue 2.rw Enumeration .1.3.6.1.4.1.7262.4.5.9.1.1.11.1.3 |
mwrPolicyQ3User queue policy value for queue 3.rw Enumeration .1.3.6.1.4.1.7262.4.5.9.1.1.11.1.4 |
mwrPolicyQ4User queue policy value for queue 4.rw Enumeration .1.3.6.1.4.1.7262.4.5.9.1.1.11.1.5 |
mwrPolicyQ5User queue policy value for queue 5.rw Enumeration .1.3.6.1.4.1.7262.4.5.9.1.1.11.1.6 |
mwrPolicyQ6User queue policy value for queue 6.rw Enumeration .1.3.6.1.4.1.7262.4.5.9.1.1.11.1.7 |
mwrPolicyQ7User queue policy value for queue 7.rw Enumeration .1.3.6.1.4.1.7262.4.5.9.1.1.11.1.8 |
mwrPolicyQ8User queue policy value for queue 8.rw Enumeration .1.3.6.1.4.1.7262.4.5.9.1.1.11.1.9 |
mwrPolicyQRowStatusThe queue policy table Row status. This object is used to apply all queue policy settings simultaneously.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.9.1.1.11.1.10 |
mwrUserClassTableA table containing QOS user class settings, the configuration corresponds to the egress QoS of radio port. SEQUENCE OF MwrUserClassEntry .1.3.6.1.4.1.7262.4.5.9.1.1.12 |
mwrUserClassEntryA table entry containing QOS user class settings. MwrUserClassEntry .1.3.6.1.4.1.7262.4.5.9.1.1.12.1 |
mwrUserClassIndexSpecifies user class queue index for each radio queue. ClassType .1.3.6.1.4.1.7262.4.5.9.1.1.12.1.1 |
mwrUserClassOffsetSpecifies user class offset value.rw Integer32 .1.3.6.1.4.1.7262.4.5.9.1.1.12.1.2 |
mwrUserClassValueSpecifies user class value.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.9.1.1.12.1.3 |
mwrUserClassMaskSpecifies user class mask.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.9.1.1.12.1.4 |
mwrUserFlowTableA table containing QOS user flow settings, the configuration corresponds to the egress QoS of radio port. SEQUENCE OF MwrUserFlowEntry .1.3.6.1.4.1.7262.4.5.9.1.1.13 |
mwrUserFlowEntryA table entry containing QOS user flow settings. MwrUserFlowEntry .1.3.6.1.4.1.7262.4.5.9.1.1.13.1 |
mwrUserFlowIndexSpecifies user flow filter queue index for each queue. FlowType .1.3.6.1.4.1.7262.4.5.9.1.1.13.1.1 |
mwrUserFlowFilterSpecifies user flow filter value for each queue.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.9.1.1.13.1.2 |
mwrUserFlowMappingTableA table containing QOS user flow mapping settings in port isolation mode. SEQUENCE OF MwrUserFlowMappingEntry .1.3.6.1.4.1.7262.4.5.9.1.1.14 |
mwrUserFlowMappingEntryA table entry containing QOS user flow mapping settings in port isolation mode. MwrUserFlowMappingEntry .1.3.6.1.4.1.7262.4.5.9.1.1.14.1 |
mwrUserFlowMappingIndexSpecifies user flow mapping index for each flow in port isolation mode. FlowType .1.3.6.1.4.1.7262.4.5.9.1.1.14.1.1 |
mwrUserFlowMappingStateEnables or disabled user flow mapping for a specific flow in port isolation mode.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.9.1.1.14.1.2 |
mwrUserFlowMapping1QSpecifies the selected queue for gi01 in port isolation mode.rw QueueType .1.3.6.1.4.1.7262.4.5.9.1.1.14.1.3 |
mwrUserFlowMapping2QSpecifies the selected queue for gi02 in port isolation mode.rw QueueType .1.3.6.1.4.1.7262.4.5.9.1.1.14.1.4 |
mwrUserFlowMapping3QSpecifies the selected queue for gi03 in port isolation mode.rw QueueType .1.3.6.1.4.1.7262.4.5.9.1.1.14.1.5 |
mwrUserFlowMapping4QSpecifies the selected queue for gi04 in port isolation mode.rw QueueType .1.3.6.1.4.1.7262.4.5.9.1.1.14.1.6 |
mwrUserFlowMappingRowStatusRow status for user flow mapping in port isolation mode.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.9.1.1.14.1.7 |
mwrUserFlowMappingBridgeModeTableA table containing QOS user flow mapping settings in bridge mode, the configuration corresponds to the egress QoS of radio port. SEQUENCE OF MwrUserFlowMappingBridgeModeEntry .1.3.6.1.4.1.7262.4.5.9.1.1.15 |
mwrUserFlowMappingBridgeModeEntryA table entry containing QOS user flow mapping settings in bridge mode. MwrUserFlowMappingBridgeModeEntry .1.3.6.1.4.1.7262.4.5.9.1.1.15.1 |
mwrUserFlowMappingBridgeModeIndexSpecifies user flow mapping index for each flow in bridge mode. FlowType .1.3.6.1.4.1.7262.4.5.9.1.1.15.1.1 |
mwrUserFlowMappingBridgeModeStateEnables or disabled user flow mapping for a specific flow in bridge mode.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.9.1.1.15.1.2 |
mwrUserFlowMappingBridgeModeQSpecifies the selected user flow mapping queue in bridge mode.rw QueueType .1.3.6.1.4.1.7262.4.5.9.1.1.15.1.3 |
mwrUserFlowMappingBridgeModeRowStatusRow status for user flow mapping in bridge mode.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.9.1.1.15.1.4 |
mwrEthThresholdAlarm OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.9.1.2 |
mwrPortThresholdAlarmTableA table containing threshold alarms parameters. SEQUENCE OF MwrPortThresholdAlarmEntry .1.3.6.1.4.1.7262.4.5.9.1.2.1 |
mwrPortThresholdAlarmEntryA table entry containing threshold alarms parameters. MwrPortThresholdAlarmEntry .1.3.6.1.4.1.7262.4.5.9.1.2.1.1 |
mwrPortThresholdAlarmIndexIndex to Threshold alarm table. Instance 1 indicates Radio port. Integer32 .1.3.6.1.4.1.7262.4.5.9.1.2.1.1.1 |
mwrDroppedPktsThresholdParamsThis object configures the dropped packets threshold settings. The threshold, in percent and the number of seconds that it must exceed this threshold. An example of the format of the string is as follows: '70 10'. The first parameter is the percentage of packets that are dropped, the second is the time in seconds that the threshold must be exceeded. The single quote marks i.e. ' ' are not used in the command.rw DisplayString .1.3.6.1.4.1.7262.4.5.9.1.2.1.1.2 |
mwrOutBWUtilizationThresholdParamsThis object configures the BW utilization threshold settings. The threshold, in percent and the number of seconds that it must exceed this threshold. An example of the format of the string is as follows: '70 10'. The first parameter is the percentage of BW threshold, the second is the time in seconds that the threshold must be exceeded. The single quote marks i.e. ' ' are not used in the commandrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.9.1.2.1.1.3 |
mwrThroughputThresholdParamsThis object configures the radio throughput threshold settings. The threshold, in percent and the number of seconds that it must exceed this threshold. An example of the format of the string is as follows: '70 10'. The first parameter is the percentage of the throughput, the second is the time in seconds that the threshold must be exceeded. The single quote marks i.e. ' ' are not used in the commandrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.9.1.2.1.1.4 |
mwrRadioQThresholdAlarmTableA table of radio port queue based Threshold Alarm settings, the configuration corresponds to the egress QoS of radio port. SEQUENCE OF MwrRadioQThresholdAlarmEntry .1.3.6.1.4.1.7262.4.5.9.1.2.2 |
mwrRadioQThresholdAlarmEntryA table entry of queue based Threshold Alarm settings. MwrRadioQThresholdAlarmEntry .1.3.6.1.4.1.7262.4.5.9.1.2.2.1 |
mwrRadioQThresholdAlarmIndexA unique identifier for one of the 8 queuesro QueueType .1.3.6.1.4.1.7262.4.5.9.1.2.2.1.1 |
mwrRadioQDepthThresholdParamsThe threshold, in percent, and the number of seconds that it must exceed this threshold are programmed by the user. An example of the format of the string is as follows: '70 10'. The first parameter is the percentage of queue depth, the second is the time in seconds that the threshold must be exceeded.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.9.1.2.2.1.2 |
mwrRadioQDroppedPktsThresholdParamsThe threshold, in packets, and the number of seconds that it must exceed this threshold are programmed by the user. An example of the format of the string is as follows: '70 10'. The first parameter is the number of packets that are dropped, the second is the time in seconds that the threshold must be exceeded.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.9.1.2.2.1.3 |
mwrEthernetStatus OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.9.2 |
mwrEthernetPerformance OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.9.3 |
mwrEnetPerfPortStatsTableA table containing Ethernet port statistics. SEQUENCE OF MwrEnetPerfPortStatsEntry .1.3.6.1.4.1.7262.4.5.9.3.1 |
mwrEnetPerfPortStatsEntryA table entry containing Ethernet port statistics. MwrEnetPerfPortStatsEntry .1.3.6.1.4.1.7262.4.5.9.3.1.1 |
mwrEnetPortStatsIndexA table index to Ethernet ports.ro Enumeration .1.3.6.1.4.1.7262.4.5.9.3.1.1.1 |
mwrPortStatsInOctetA 64-bit counter representing the incoming octets.ro Counter64 .1.3.6.1.4.1.7262.4.5.9.3.1.1.2 |
mwrPortStatsInGoodPktsA 64-bit counter representing the incoming good packets.ro Counter64 .1.3.6.1.4.1.7262.4.5.9.3.1.1.3 |
mwrPortStatsInErrPktsA 64-bit counter representing the incoming error packets.ro Counter64 .1.3.6.1.4.1.7262.4.5.9.3.1.1.4 |
mwrPortStatsInDiscardPktsA 64-bit counter representing the incoming discarded packets.ro Counter64 .1.3.6.1.4.1.7262.4.5.9.3.1.1.5 |
mwrPortStatsOutOctetsA 64-bit counter representing the outgoing octets.ro Counter64 .1.3.6.1.4.1.7262.4.5.9.3.1.1.6 |
mwrPortStatsOutGoodPktsA 64-bit counter representing the outgoing good packets.ro Counter64 .1.3.6.1.4.1.7262.4.5.9.3.1.1.7 |
mwrPortStatsOutErrPktsA 64-bit counter representing the outgoing error packets.ro Counter64 .1.3.6.1.4.1.7262.4.5.9.3.1.1.8 |
mwrPortStatsOutDiscardPktsA 64-bit counter representing the outgoing discarded packets.ro Counter64 .1.3.6.1.4.1.7262.4.5.9.3.1.1.9 |
mwrPortStatsOutBwUtilizationThis object represents the ratio of egress data rate and the egress link capacity of the port. The value is represented in %.ro Integer32 UNITS "%" .1.3.6.1.4.1.7262.4.5.9.3.1.1.10 |
mwrPortStatsInBwUtilizationThis object represents the ratio of ingress data rate and the ingress link capacity of the port. The value is represented in %.ro Integer32 UNITS "%" .1.3.6.1.4.1.7262.4.5.9.3.1.1.11 |
mwrPortStatsInDataRateThe Ethernet data rate coming into the port. The data rate is multiplied by 100. e.g. A display of 1530 is actually 15.30 Mpbsro Integer32 UNITS "Mbps" .1.3.6.1.4.1.7262.4.5.9.3.1.1.12 |
mwrPortStatsThroughputThe Ethernet data rate going out of the port. The data rate is multiplied by 100. e.g. A display of 1530 is actually 15.30 Mpbs.ro Integer32 UNITS "Mbps" .1.3.6.1.4.1.7262.4.5.9.3.1.1.13 |
mwrEnetPerfPortStats32BitTableA table containing 32-bit Ethernet statistics. This table is provided to satisfy snmp v1 users where they can't access 64-bit counters. SEQUENCE OF MwrEnetPerfPortStats32BitEntry .1.3.6.1.4.1.7262.4.5.9.3.2 |
mwrEnetPerfPortStats32BitEntryA table entry containing 32-bit Ethernet statistics. This table is provided to satisfy snmp v1 users where they can't access 64-bit counters. MwrEnetPerfPortStats32BitEntry .1.3.6.1.4.1.7262.4.5.9.3.2.1 |
mwrPortStats32BitIndexA table index to ports carrying Ethernet packets. Enumeration .1.3.6.1.4.1.7262.4.5.9.3.2.1.1 |
mwrPortStatsInOctet32BitA 32-bit counter representing the incoming octets.ro Counter32 .1.3.6.1.4.1.7262.4.5.9.3.2.1.2 |
mwrPortStatsInGoodPkts32BitA 32-bit counter representing the incoming good packets.ro Counter32 .1.3.6.1.4.1.7262.4.5.9.3.2.1.3 |
mwrPortStatsInErrPkts32BitA 32-bit counter representing the incoming error packets.ro Counter32 .1.3.6.1.4.1.7262.4.5.9.3.2.1.4 |
mwrPortStatsInDiscardPkts32BitA 32-bit counter representing the incoming discarded packets.ro Counter32 .1.3.6.1.4.1.7262.4.5.9.3.2.1.5 |
mwrPortStatsOutOctets32BitA 32-bit counter representing the outgoing octets.ro Counter32 .1.3.6.1.4.1.7262.4.5.9.3.2.1.6 |
mwrPortStatsOutGoodPkts32BitA 32-bit counter representing the outgoing good packets.ro Counter32 .1.3.6.1.4.1.7262.4.5.9.3.2.1.7 |
mwrPortStatsOutErrPkts32BitA 32-bit counter representing the outgoing error packets.ro Counter32 .1.3.6.1.4.1.7262.4.5.9.3.2.1.8 |
mwrPortStatsOutDiscardPkts32BitA 32-bit counter representing the outgoing discarded packets.ro Counter32 .1.3.6.1.4.1.7262.4.5.9.3.2.1.9 |
mwrEnetPerfRadioQStatsTableA table containing radio queue statistics. SEQUENCE OF MwrEnetPerfRadioQStatsEntry .1.3.6.1.4.1.7262.4.5.9.3.3 |
mwrEnetPerfRadioQStatsEntryA table entry containing radio queue statistics. MwrEnetPerfRadioQStatsEntry .1.3.6.1.4.1.7262.4.5.9.3.3.1 |
mwrRadioQStatsIndexA unique value for each of the 8 queues. QueueType .1.3.6.1.4.1.7262.4.5.9.3.3.1.1 |
mwrRadioQStatsInGoodPktsThe current count of packets in queues.ro Counter64 .1.3.6.1.4.1.7262.4.5.9.3.3.1.2 |
mwrRadioQStatsInDiscardPktsThe current count of packets received in queues that were discarded due to queue overflow.ro Counter64 .1.3.6.1.4.1.7262.4.5.9.3.3.1.3 |
mwrRadioQStatsOutBwUtilizationThe ratio of egress data rate and user configured radio queue CIR.ro Integer32 UNITS "%" .1.3.6.1.4.1.7262.4.5.9.3.3.1.4 |
mwrRadioQStatsInDataRateThe ingress data rate of the radio queue.ro Integer32 UNITS "Mbps" .1.3.6.1.4.1.7262.4.5.9.3.3.1.5 |
mwrRadioQStatsThroughputThe throughput of the radio queue.ro Integer32 UNITS "Mbps" .1.3.6.1.4.1.7262.4.5.9.3.3.1.6 |
mwrEnetPerfRadioQStats32BitTableA table containing 32-bit counters for radio queue statistics. SEQUENCE OF MwrEnetPerfRadioQStats32BitEntry .1.3.6.1.4.1.7262.4.5.9.3.4 |
mwrEnetPerfRadioQStats32BitEntryA table entry containing 32-bit counters for radio queue statistics. MwrEnetPerfRadioQStats32BitEntry .1.3.6.1.4.1.7262.4.5.9.3.4.1 |
mwrRadioQStats32BitIndexA unique value for each of the 8 queues. QueueType .1.3.6.1.4.1.7262.4.5.9.3.4.1.1 |
mwrRadioQStatsInGoodPkts32BitA 32-bit counter representing the current count of packets in queues.ro Counter32 .1.3.6.1.4.1.7262.4.5.9.3.4.1.2 |
mwrRadioQStatsDiscardPkts32BitA 32-bit counter representing the current count of packets received in queues that were discarded due to queue overflow .ro Counter32 .1.3.6.1.4.1.7262.4.5.9.3.4.1.3 |
mwrEthernetNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.9.4 |
mwrDroppedPktsThresholdThis notification is raised when the ethernet packet drops in an interface has exceeded user set limit. NOTIFICATION-TYPE .1.3.6.1.4.1.7262.4.5.9.4.1 |
mwrRadioQDroppedPktsThresholdThis notification is raised when Ethernet packet drops over radio traffic queue has exceeded the user configured limit. The mwrRadioQThresholdAlarmIndex varbind indicates specific queue number. NOTIFICATION-TYPE .1.3.6.1.4.1.7262.4.5.9.4.2 |
mwrRadioQDepthThresholdThis notification is raised when the data buffered in the specific radio traffic queue has exceeded the user set limit. The mwrRadioQThresholdAlarmIndex varbind indicates specific queue number. NOTIFICATION-TYPE .1.3.6.1.4.1.7262.4.5.9.4.3 |
mwrOutBWUtilizationThresholdThis notification is raised when the out bandwidth utilization of an interface has exceeded the user configured limit. NOTIFICATION-TYPE .1.3.6.1.4.1.7262.4.5.9.4.4 |
mwrThroughputThresholdThis notification is raised when the throughput of an interface has exceeded the user configured limit. NOTIFICATION-TYPE .1.3.6.1.4.1.7262.4.5.9.4.5 |
mwrAcm OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.10 |
mwrAcmConfigurations OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.10.1 |
mwrAcmManualModeEnables or disables the Adaptive Coding Modulation (ACM) Manual Mode.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.10.1.1 |
mwrAcmStateEnables or disables the Adaptive Code Modulation (ACM).rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.10.1.2 |
mwrAcmWaitToRestoreThis object configures the ACM wait to restore duration time in seconds.rw Integer32 .1.3.6.1.4.1.7262.4.5.10.1.3 |
mwrAcmModeTableA table containing available Adaptive Code Modulation (ACM) tx profiles. SEQUENCE OF MwrAcmModeEntry .1.3.6.1.4.1.7262.4.5.10.1.4 |
mwrAcmModeEntryA table entry containing available Adaptive Code Modulation (ACM) tx profiles. MwrAcmModeEntry .1.3.6.1.4.1.7262.4.5.10.1.4.1 |
mwrAcmModeIndexA unique value for each Adaptive Code Modulation (ACM) tx profile. Integer32 .1.3.6.1.4.1.7262.4.5.10.1.4.1.1 |
mwrAcmTxProfileNameThe Adaptive Code Modulation (ACM) tx profile name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.10.1.4.1.2 |
mwrAcmTxProfileRangeSpecifies the range for the Adaptive Code Modulation (ACM) TX Profile.rw Enumeration .1.3.6.1.4.1.7262.4.5.10.1.4.1.3 |
mwrAcmStatus OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.10.2 |
mwrAcmStatusTableA table containing Adaptive Code Modulation (ACM) status. SEQUENCE OF MwrAcmStatusEntry .1.3.6.1.4.1.7262.4.5.10.2.1 |
mwrAcmStatusEntryA table entry containing Adaptive Code Modulation (ACM) status. MwrAcmStatusEntry .1.3.6.1.4.1.7262.4.5.10.2.1.1 |
mwrAcmStatusIndexA unique value for each interface. RadioInstanceType .1.3.6.1.4.1.7262.4.5.10.2.1.1.1 |
mwrAcmActualTxProfileA read-only string specifying the currently running ACM TX profile.ro DisplayString .1.3.6.1.4.1.7262.4.5.10.2.1.1.2 |
mwrAcmDiagnostics OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.10.3 |
mwrAcmDiagTableA table containing ACM diagnostic settings. SEQUENCE OF MwrAcmDiagEntry .1.3.6.1.4.1.7262.4.5.10.3.1 |
mwrAcmDiagEntryA table entry containing ACM diagnostic settings. MwrAcmDiagEntry .1.3.6.1.4.1.7262.4.5.10.3.1.1 |
mwrAcmDiagIndexA unique value for each radio channel if applicable. RadioInstanceType .1.3.6.1.4.1.7262.4.5.10.3.1.1.1 |
mwrAcmDiagnoseThis service effecting object accepts either 'up' or 'down' to diagnose whether the modulation speed can be increased or decreased. Poll the mwrAcmDiagnosticResult object to determine the results.rw Enumeration .1.3.6.1.4.1.7262.4.5.10.3.1.1.2 |
mwrAcmDiagnosticResultThe result from ACM Diagnostic is read from this object.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.10.3.1.1.3 |
mwrAcmNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.10.4 |
mwrAcmConfigMismatchThis notification is raised when ACM configuration mismatch between the link partners. NOTIFICATION-TYPE .1.3.6.1.4.1.7262.4.5.10.4.1 |
mwrAcmProfileLoweredThis notification is raised when system is executing ACM and working at a lower radio profile than the configured nominal radio profile. NOTIFICATION-TYPE .1.3.6.1.4.1.7262.4.5.10.4.2 |
mwrAcmProfileChangedThis notification is raised when system is executing in ACM and has changed the radio profile. NOTIFICATION-TYPE .1.3.6.1.4.1.7262.4.5.10.4.3 |
mwrAtpc OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.11 |
mwrAtpcConfigurations OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.11.1 |
mwrAtpcConfigurationsTableTable containing ATPC configurations. SEQUENCE OF MwrAtpcConfigurationsEntry .1.3.6.1.4.1.7262.4.5.11.1.1 |
mwrAtpcConfigurationsEntryTable entry containing ATPC configurations. MwrAtpcConfigurationsEntry .1.3.6.1.4.1.7262.4.5.11.1.1.1 |
mwrAtpcConfigIndexA unique value for each of the radio channel instance. RadioInstanceType .1.3.6.1.4.1.7262.4.5.11.1.1.1.1 |
mwrAtpcStateIndicates whether the Adaptive Transmit Power Control (ATPC) feature is enabled.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.11.1.1.1.2 |
mwrAtpcCoordinatedPowerThis object is the value at which the system will transmit if the ATPC and the coordinated power are enabled. This is only if the system is transmitting the maximum power for 5 minutes. The value is multiplied by 10. e.g. A display of 133 is actually 13.3 dB.rw Integer32 UNITS "dB" .1.3.6.1.4.1.7262.4.5.11.1.1.1.3 |
mwrAtpcCoordinatedPowerEnableIndicates whether Adaptive Transmit Power Control (ATPC) coordinated power option is enabled.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.11.1.1.1.4 |
mwrAtpcMinTxPowerSets the minimum ATPC transmit power in dB x 10.rw Integer32 UNITS "dB" .1.3.6.1.4.1.7262.4.5.11.1.1.1.5 |
mwrAtpcMaxTxPowerSets the maximum ATPC transmit power in dB x 10. When ATPC is enabled, transmit power range will be between ATPC min. and ATPC max. power.rw Integer32 UNITS "dB" .1.3.6.1.4.1.7262.4.5.11.1.1.1.6 |
mwrAtpcRslTargetThis object configures Received Signal Level that should be maintained by the link by adjusting the transmit power when ATPC is enabled.rw Integer32 .1.3.6.1.4.1.7262.4.5.11.1.1.1.7 |
mwrAtpcRslTargetUseDefaultWhen this object is enabled the default RSL target will be used instead of the configured mwrAtpcRslTarget. The mwrAtpcDefaultRslTarget displays the default value.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.11.1.1.1.8 |
mwrAtpcStatus OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.11.2 |
mwrAtpcStatusTableA table containing ATPC status. SEQUENCE OF MwrAtpcStatusEntry .1.3.6.1.4.1.7262.4.5.11.2.1 |
mwrAtpcStatusEntryA table entry containing ATPC status. MwrAtpcStatusEntry .1.3.6.1.4.1.7262.4.5.11.2.1.1 |
mwrAtpcStatusIndexA unique value for each of the radio instance. RadioInstanceType .1.3.6.1.4.1.7262.4.5.11.2.1.1.1 |
mwrAtpcRunningStatusIndicates the actual condition of ATPC: - disabled: Configuration is set to off. - disabledAuto: Feature was automatically disabled and is transmitting at coordinated power. - running: Feature is running normally. - runningToggling: Feature is toggling between maximum and minimum power to recover from a loss of mod sync. - suspended: Feature was suspended. - suspendedLostComm: Feature is suspended because communication is lost with peer ATPC. - suspendedRadioDown: Feature is suspended because the radio is down. - suspendedRadioMuted: Feature is suspended because the radio is muted. - suspendedRadioLoopback: Feature is suspended because the radio is in loopback mode.ro Enumeration .1.3.6.1.4.1.7262.4.5.11.2.1.1.2 |
mwrAtpcDefaultRslTargetThis object is the default value of the Received Signal Level target when ATPC is enabled.ro Integer32 .1.3.6.1.4.1.7262.4.5.11.2.1.1.3 |
mwrAtpcActualMinTxPowerThis object indicates the running configuration for ATPC min tx power.ro Integer32 .1.3.6.1.4.1.7262.4.5.11.2.1.1.4 |
mwrAtpcActualMaxTxPowerThis object indicates the running configuration for ATPC max tx power.ro Integer32 .1.3.6.1.4.1.7262.4.5.11.2.1.1.5 |
mwrAtpcActualCoordinatedPowerThis value is the running configuration of the coordinated power. The value is multiplied by 10. e.g. A display of 133 is actually 13.3 dB.ro Integer32 .1.3.6.1.4.1.7262.4.5.11.2.1.1.6 |
mwrAtpcPeerRslTargetThis object is the peer Received Signal Level target when ATPC is enabled.ro Integer32 .1.3.6.1.4.1.7262.4.5.11.2.1.1.7 |
mwrAtpcMinRslTargetRepresents the minimum RSL target value.ro Integer32 .1.3.6.1.4.1.7262.4.5.11.2.1.1.8 |
mwrAtpcMaxRslTargetRepresents the maximum RSL target value.ro Integer32 .1.3.6.1.4.1.7262.4.5.11.2.1.1.9 |
mwrAtpcPeerRslThis object represents the peer actual RSL value. Divide the value by 10 to get the actual RSL value. Once this number is divided by 10 the units are dB. For example -352 is actually -35.2dBro Integer32 .1.3.6.1.4.1.7262.4.5.11.2.1.1.10 |
mwrAtpcNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.11.3 |
mwrAtpcConfigMismatchThis notification is raised when ATPC configuration mismatch has occurred between link partners. NOTIFICATION-TYPE .1.3.6.1.4.1.7262.4.5.11.3.1 |
mwrAtpcAutoDisabledThis notification is raised when ATPC is automatically disabled due to coordinated power condition. When this notification is raised the radio will be transmitting at coordinated power. The mwrAtpcStatusIndex varbind indicates the radio instance. NOTIFICATION-TYPE .1.3.6.1.4.1.7262.4.5.11.3.2 |
mwrRadio OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.12 |
mwrCompression OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.13 |
mwrCompressionConfigurations OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.13.1 |
mwrBacRecordAvgPeriodConfigures the average period used for computing the running average BAC gain and uncompressed ratio. Default average period is set to 10 seconds.rw Integer32 .1.3.6.1.4.1.7262.4.5.13.1.1 |
mwrBacTableTable containing Bandwidth Acceleration entries. SEQUENCE OF MwrBacEntry .1.3.6.1.4.1.7262.4.5.13.1.2 |
mwrBacEntryContains Bandwidth Acceleration entries. MwrBacEntry .1.3.6.1.4.1.7262.4.5.13.1.2.1 |
mwrBacQIndexA unique value for each of the 8 radio egress Queues. QueueType .1.3.6.1.4.1.7262.4.5.13.1.2.1.1 |
mwrBacQEnableConfigure queue compression state to disable/enable.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.13.1.2.1.2 |
mwrBacQBlockSizeConfigure queue compression block size (256...8000). Block size has to be in increments of 64 bytes. Otherwise it will be rounded off to nearest 64 bytes. Valid block sizes are <256 512 1024 4032 8000>rw Integer32 .1.3.6.1.4.1.7262.4.5.13.1.2.1.3 |
mwrBacRecordLoggingEnables/disables logging of BAC related statistics like Maximum BAC gain and Maximum uncompressed ratio on a per queue basis to syslog and flashlog.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.13.1.2.1.4 |
mwrHcQTableA table containing Header Compression settings for each queue, the configuration corresponds to the egress QoS of radio port. SEQUENCE OF MwrHcQEntry .1.3.6.1.4.1.7262.4.5.13.1.3 |
mwrHcQEntryA table entry containing Header Compression settings for each queue. MwrHcQEntry .1.3.6.1.4.1.7262.4.5.13.1.3.1 |
mwrHcQIndexSpecifies Header Compression queue index for each radio queue. QueueType .1.3.6.1.4.1.7262.4.5.13.1.3.1.1 |
mwrHcQ1Enables or disables the Header Compression on queue 1.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.13.1.3.1.2 |
mwrHcQ2Enables or disables the Header Compression on queue 2.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.13.1.3.1.3 |
mwrHcQ3Enables or disables the Header Compression on queue 3.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.13.1.3.1.4 |
mwrHcQ4Enables or disables the Header Compression on queue 4.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.13.1.3.1.5 |
mwrHcQ5Enables or disables the Header Compression on queue 5.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.13.1.3.1.6 |
mwrHcQ6Enables or disables the Header Compression on queue 6.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.13.1.3.1.7 |
mwrHcQ7Enables or disables the Header Compression on queue 7.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.13.1.3.1.8 |
mwrHcQ8Enables or disables the Header Compression on queue 8.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.13.1.3.1.9 |
mwrHcQRowStatusThe Header Compression table Row Status. This object is used to apply Header Compression settings for all queues simultaneously.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.13.1.3.1.10 |
mwrCompressionStatus OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.13.2 |
mwrBacStatusTableTable containing Bandwidth Acceleration status entries. SEQUENCE OF MwrBacStatusEntry .1.3.6.1.4.1.7262.4.5.13.2.1 |
mwrBacStatusEntryContains Bandwidth Acceleration status entries. MwrBacStatusEntry .1.3.6.1.4.1.7262.4.5.13.2.1.1 |
mwrBacStatusQIndexA unique value for each of the 8 Queues. QueueType .1.3.6.1.4.1.7262.4.5.13.2.1.1.1 |
mwrBacUncompressedRatioRunning average Uncompressed ratio is calculated by collecting n samples of bytes uncompressed and bytes in to queue over specified average period in percentage.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.13.2.1.1.2 |
mwrBacGainThe Running Average BAC gain is the sum of all bytes getting into the compressor divided by the sum of all compressed and uncompressed bytes calculated over an average period.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.13.2.1.1.3 |
mwrCompressionNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.13.3 |
mwrEvents OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.14 |
mwrEventsConfigurations OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.14.1 |
mwrEventConfigTableA table of alarm configuration SEQUENCE OF MwrEventConfigEntry .1.3.6.1.4.1.7262.4.5.14.1.1 |
mwrEventConfigEntryAn entry of alarm configuration MwrEventConfigEntry .1.3.6.1.4.1.7262.4.5.14.1.1.1 |
mwrEventConfigIndexA unique value for each alarm. Unsigned32 .1.3.6.1.4.1.7262.4.5.14.1.1.1.1 |
mwrEventInstanceIndexA unique value for each instance of an alarm.ro Unsigned32 .1.3.6.1.4.1.7262.4.5.14.1.1.1.2 |
mwrEventConfigSeverityThe severity of the alarm as minor, major or critical.rw Enumeration .1.3.6.1.4.1.7262.4.5.14.1.1.1.3 |
mwrEventNameRepresents the event name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.14.1.1.1.4 |
mwrAlarmConfigStateThe state of the alarm which can be either enabled or disabled.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.14.1.1.1.5 |
mwrTrapConfigStateThe state of the trap which can be either enabled or disabled.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.14.1.1.1.6 |
mwrLogEventStateThis object is used to enable or disable logging the events.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.14.1.1.1.7 |
mwrLogs OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.15 |
mwrLogsConfigurations OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.15.1 |
mwrEventLogEnableIndicates whether event log is enabled.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.15.1.1 |
mwrPerfmLogEnableIndicates whether performance log is enabled.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.15.1.2 |
mwrPerfmLogIntervalPerformance statistics are logged periodically by this interval. The interval can be up to 00:15:00 (15 minutes) and as short as 00:00:1 (1 seconds).rw DisplayString .1.3.6.1.4.1.7262.4.5.15.1.3 |
mwrSysLogServerTableThe syslog server table. SEQUENCE OF MwrSysLogServerEntry .1.3.6.1.4.1.7262.4.5.15.1.4 |
mwrSysLogServerEntryThe syslog server table entry. MwrSysLogServerEntry .1.3.6.1.4.1.7262.4.5.15.1.4.1 |
mwrSysLogServerIndexThe syslog server table index. Integer32 .1.3.6.1.4.1.7262.4.5.15.1.4.1.1 |
mwrSysLogEnableIndicates whether sys log is enabled.rw EnableType (EQUIPMENT-COMMON-MIB) .1.3.6.1.4.1.7262.4.5.15.1.4.1.2 |
mwrSysLogHostDomainIndicates sys log host inet address type. Valid types are ipv4 or ipv6.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.7262.4.5.15.1.4.1.3 |
mwrSysLogHostAddressIndicates sys log host inet address octet string.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.7262.4.5.15.1.4.1.4 |
mwrPM OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.16 |
mwrPMConfigurations OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.16.1 |
mwrPmRspiThresholdTablePerformance Monitoring table for Radio Synchronous Physical Interface thresholds. SEQUENCE OF MwrPmRspiThresholdEntry .1.3.6.1.4.1.7262.4.5.16.1.1 |
mwrPmRspiThresholdEntryContains entries for Radio Synchronous Physical Interface thresholds. MwrPmRspiThresholdEntry .1.3.6.1.4.1.7262.4.5.16.1.1.1 |
mwrPmRspiThrIndexIndex to PM RSPI Threshold table. RadioInstanceType .1.3.6.1.4.1.7262.4.5.16.1.1.1.1 |
mwrPmRLT1Receive Level Threshold 1, represents the value of the first received power level threshold.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.1.1.2 |
mwrPmRLT2Receive Level Threshold 2, represents the value of the second received power level threshold.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.1.1.3 |
mwrPmRLT3Receive Level Threshold 3, represents the value of the third received power level threshold.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.1.1.4 |
mwrPmRLT4Receive Level Threshold 4, represents the value of the fourth received power level threshold.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.1.1.5 |
mwrPmTLT1Transmit Level Threshold 1, represents the value of the first transmitted power level threshold.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.1.1.6 |
mwrPmTLT2Transmit Level Threshold 2, represents the value of the second transmitted power level threshold.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.1.1.7 |
mwrPmRspiThrRowStatusThis object is used for applying all RSPI thresholds simultaneously. Set RowStatus to NotInService, make changes to all or some threshold values and then change RowStatus back to Active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.16.1.1.1.8 |
mwrPmBwThresholdTablePerformance monitoring out bandwidth utilization thresholds table. SEQUENCE OF MwrPmBwThresholdEntry .1.3.6.1.4.1.7262.4.5.16.1.2 |
mwrPmBwThresholdEntryContains entries for performance monitoring out bandwidth utilization thresholds. MwrPmBwThresholdEntry .1.3.6.1.4.1.7262.4.5.16.1.2.1 |
mwrPmBWThrIndexIndex to PM out BW Threshold table. Index 1 represents the radio port. Integer32 .1.3.6.1.4.1.7262.4.5.16.1.2.1.1 |
mwrPmBWT1The performance monitoring out BW utilization threshold 1.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.2.1.2 |
mwrPmBWT2The performance monitoring out BW utilization threshold 2.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.2.1.3 |
mwrPmBWT3The performance monitoring out BW utilization threshold 3.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.2.1.4 |
mwrPmBWT4The performance monitoring out BW utilization threshold 4.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.2.1.5 |
mwrPmBWT5The performance monitoring out BW utilization threshold 5.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.2.1.6 |
mwrPmBWT6The performance monitoring out BW utilization threshold 6.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.2.1.7 |
mwrPmBWT7The performance monitoring out BW utilization threshold 7.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.2.1.8 |
mwrPmBWT8The performance monitoring out BW utilization threshold 8.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.2.1.9 |
mwrPmBWT9The performance monitoring out BW utilization threshold 9.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.2.1.10 |
mwrPmBWT10The performance monitoring out BW utilization threshold 10.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.2.1.11 |
mwrPmBWTRowStatusThis object is used for applying all PM bandwidth threshold settings simultaneously. Set RowStatus to NotInService, make changes to all or some threshold values and then change RowStatus back to Active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.16.1.2.1.12 |
mwrPmTpThresholdTablePerformance monitoring throughput thresholds table. SEQUENCE OF MwrPmTpThresholdEntry .1.3.6.1.4.1.7262.4.5.16.1.3 |
mwrPmTpThresholdEntryContains entries for performance monitoring throughput thresholds. MwrPmTpThresholdEntry .1.3.6.1.4.1.7262.4.5.16.1.3.1 |
mwrPmTPThrIndexIndex to PM throughput Threshold table. Index 1 represents the radio port. Integer32 .1.3.6.1.4.1.7262.4.5.16.1.3.1.1 |
mwrPmTPT1The performance monitoring throughput threshold 1.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.3.1.2 |
mwrPmTPT2The performance monitoring throughput threshold 2.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.3.1.3 |
mwrPmTPT3The performance monitoring throughput threshold 3.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.3.1.4 |
mwrPmTPT4The performance monitoring throughput threshold 4.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.3.1.5 |
mwrPmTPT5The performance monitoring throughput threshold 5.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.3.1.6 |
mwrPmTPT6The performance monitoring throughput threshold 6.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.3.1.7 |
mwrPmTPT7The performance monitoring throughput threshold 7.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.3.1.8 |
mwrPmTPT8The performance monitoring throughput threshold 8.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.3.1.9 |
mwrPmTPT9The performance monitoring throughput threshold 9.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.3.1.10 |
mwrPmTPT10The performance monitoring throughput threshold 10.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.3.1.11 |
mwrPmTPTRowStatusThis object is used for applying all PM throughput threshold settings simultaneously. Set RowStatus to NotInService, make changes to all or some threshold values and then change RowStatus back to Active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.16.1.3.1.12 |
mwrPmAdvThresholdTableThe advanced performance monitoring thresholds table. SEQUENCE OF MwrPmAdvThresholdEntry .1.3.6.1.4.1.7262.4.5.16.1.4 |
mwrPmAdvThresholdEntryThe advanced performance monitoring thresholds entries. MwrPmAdvThresholdEntry .1.3.6.1.4.1.7262.4.5.16.1.4.1 |
mwrPmAdvThrIndexThe advanced performance monitoring thresholds table index. Index 1 represents the radio port. Integer32 .1.3.6.1.4.1.7262.4.5.16.1.4.1.1 |
mwrPmAdvTxHitsT1The advanced performance monitoring Tx hits threshold 1.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.4.1.2 |
mwrPmAdvRxHitsT1The advanced performance monitoring Rx hits threshold 1.rw Integer32 .1.3.6.1.4.1.7262.4.5.16.1.4.1.3 |
mwrPmAdvRowStatusThis object is used for applying all PM advanced threshold settings simultaneously. Set RowStatus to NotInService, make changes to all threshold values and then change back RowStatus to Active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.16.1.4.1.4 |
mwrPMStatus OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.16.2 |
mwrPmRspiTablePerformance Monitoring table for Radio Synchronous Physical Interface. SEQUENCE OF MwrPmRspiEntry .1.3.6.1.4.1.7262.4.5.16.2.1 |
mwrPmRspiEntryContains information for Radio Synchronous Physical Interface. The table is indexed by the granularity period and by the interval number. 22 rows are always presents, 20 are the historical measurements for 16 intervals in the quarter granularity and 4 intervals in the 24 hours granularity period. 2 rows represent the current measures. MwrPmRspiEntry .1.3.6.1.4.1.7262.4.5.16.2.1.1 |
mwrPmRspiStatusIndexA unique value for each of the radio instance. RadioInstanceType .1.3.6.1.4.1.7262.4.5.16.2.1.1.1 |
mwrPmRspiIntervalThe interval period of the row. Quarter means the 15 minutes interval and day means the 24 hours interval. PMIntervalType .1.3.6.1.4.1.7262.4.5.16.2.1.1.2 |
mwrPmRspiIntervalIDThe interval identifier of the row, from 1 (last quarter) to 16 (oldest quarter) for the 15-minute and from 1 (yesterday) to 4 (4 days ago) for the 24-hour. Value 0 can be used to retrieve current measurements, according to the requested granularity. Integer32 .1.3.6.1.4.1.7262.4.5.16.2.1.1.3 |
mwrPmRspiMeasSuspectAny problem that invalidates the measurement.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.16.2.1.1.4 |
mwrPmRspiMeasIntervalStatusAn indication if the interval is a valid measurement. When the system comes up, all the previous intervals are invalid.ro Enumeration .1.3.6.1.4.1.7262.4.5.16.2.1.1.5 |
mwrPmRspiMeasTimeLengthThe interval duration in seconds.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.7262.4.5.16.2.1.1.6 |
mwrPmRspiMeasTLTMMinThe transmitted power level tide mark low value.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.1.1.7 |
mwrPmRspiMeasTLTMMaxThe transmitted power level tide mark high value.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.1.1.8 |
mwrPmRspiMeasTLTS1The number of seconds above the first transmitted power level threshold.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.7262.4.5.16.2.1.1.9 |
mwrPmRspiMeasTLTS2The number of seconds above the second transmitted power level threshold.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.7262.4.5.16.2.1.1.10 |
mwrPmRspiMeasRLTMMinThe received power level tide mark low value.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.1.1.11 |
mwrPmRspiMeasRLTMMaxThe received power level tide mark high value.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.1.1.12 |
mwrPmRspiMeasRLTS1The number of seconds below the first received power level threshold.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.7262.4.5.16.2.1.1.13 |
mwrPmRspiMeasRLTS2The number of seconds below the second received power level threshold.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.7262.4.5.16.2.1.1.14 |
mwrPmRspiMeasRLTS3The number of seconds below the third received power level threshold.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.7262.4.5.16.2.1.1.15 |
mwrPmRspiMeasRLTS4The number of seconds below the fourth received power level threshold.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.7262.4.5.16.2.1.1.16 |
mwrPmBWTableTable containing performance monitoring measurements in 15 min and 24 hrs intervals for out BW utilization. SEQUENCE OF MwrPmBWEntry .1.3.6.1.4.1.7262.4.5.16.2.2 |
mwrPmBWEntryTable entries containing performance monitoring measurements in 15 min and 24 hrs intervals for out BW utilization. MwrPmBWEntry .1.3.6.1.4.1.7262.4.5.16.2.2.1 |
mwrPmBWStatusIndexThe performance monitoring out BW utilization measurements table index. Index 1 represents the radio port. Integer32 .1.3.6.1.4.1.7262.4.5.16.2.2.1.1 |
mwrPmBWIntervalThe interval period of the row. Quarter means the 15 minutes interval and day means the 24 hours interval. PMIntervalType .1.3.6.1.4.1.7262.4.5.16.2.2.1.2 |
mwrPmBWIntervalIDThe interval identifier of the row, from 1 (last quarter) to 16 (oldest quarter) for the 15-minute and from 1 (yesterday) to 4 (4 days ago) for the 24-hour. Value 0 can be used to retrieve current measurements, according to the requested granularity. Integer32 .1.3.6.1.4.1.7262.4.5.16.2.2.1.3 |
mwrPmBWMeasSuspectAny problem that invalidates the measurement.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.16.2.2.1.4 |
mwrPmBWMeasIntervalStatusAn indication if the interval is a valid measurement. When the system comes up, all the previous intervals are invalid.ro Enumeration .1.3.6.1.4.1.7262.4.5.16.2.2.1.5 |
mwrPmBWMeasTimeLengthThe interval duration in seconds.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.2.1.6 |
mwrPmMeasBWTS1The number of seconds above the first BW utilization threshold.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.2.1.7 |
mwrPmMeasBWTS2The number of seconds above the second BW utilization threshold.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.2.1.8 |
mwrPmMeasBWTS3The number of seconds above the third BW utilization threshold.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.2.1.9 |
mwrPmMeasBWTS4The number of seconds above the fourth BW utilization threshold.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.2.1.10 |
mwrPmMeasBWTS5The number of seconds above the fifth BW utilization threshold.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.2.1.11 |
mwrPmMeasBWTS6The number of seconds above the sixth BW utilization threshold.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.2.1.12 |
mwrPmMeasBWTS7The number of seconds above the seventh BW utilization threshold.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.2.1.13 |
mwrPmMeasBWTS8The number of seconds above the eighth BW utilization threshold.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.2.1.14 |
mwrPmMeasBWTS9The number of seconds above the ninth BW utilization threshold.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.2.1.15 |
mwrPmMeasBWTS10The number of seconds above the tenth BW utilization threshold.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.2.1.16 |
mwrPmTPTableTable containing performance monitoring measurements in 15 min and 24 hrs intervals for throughput. SEQUENCE OF MwrPmTPEntry .1.3.6.1.4.1.7262.4.5.16.2.3 |
mwrPmTPEntryTable entry containing performance monitoring throughput measurements in 15 min and 24 hrs intervals. MwrPmTPEntry .1.3.6.1.4.1.7262.4.5.16.2.3.1 |
mwrPmTPStatusIndexThe performance monitoring throughput measurements table index. Index 1 represents the radio port. Integer32 .1.3.6.1.4.1.7262.4.5.16.2.3.1.1 |
mwrPmTPIntervalThe interval period of the row. Quarter means the 15 minutes interval and day means the 24 hours interval. PMIntervalType .1.3.6.1.4.1.7262.4.5.16.2.3.1.2 |
mwrPmTPIntervalIDThe interval identifier of the row, from 1 (last quarter) to 16 (oldest quarter) for the 15-minute and from 1 (yesterday) to 4 (4 days ago) for the 24-hour. Value 0 can be used to retrieve current measurements, according to the requested granularity. Integer32 .1.3.6.1.4.1.7262.4.5.16.2.3.1.3 |
mwrPmTPMeasSuspectAny problem that invalidates the measurement.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.16.2.3.1.4 |
mwrPmTPMeasIntervalStatusAn indication if the interval is a valid measurement. When the system comes up, all the previous intervals are invalid.ro Enumeration .1.3.6.1.4.1.7262.4.5.16.2.3.1.5 |
mwrPmTPMeasTimeLengthThe interval duration in seconds.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.3.1.6 |
mwrPmMeasTPTS1The number of seconds above the first throughput threshold.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.3.1.7 |
mwrPmMeasTPTS2The number of seconds above the second throughput threshold.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.3.1.8 |
mwrPmMeasTPTS3The number of seconds above the third throughput threshold.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.3.1.9 |
mwrPmMeasTPTS4The number of seconds above the fourth throughput threshold.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.3.1.10 |
mwrPmMeasTPTS5The number of seconds above the fifth throughput threshold.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.3.1.11 |
mwrPmMeasTPTS6The number of seconds above the sixth throughput threshold.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.3.1.12 |
mwrPmMeasTPTS7The number of seconds above the seventh throughput threshold.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.3.1.13 |
mwrPmMeasTPTS8The number of seconds above the eighth throughput threshold.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.3.1.14 |
mwrPmMeasTPTS9The number of seconds above the ninth throughput threshold.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.3.1.15 |
mwrPmMeasTPTS10The number of seconds above the tenth throughput threshold.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.3.1.16 |
mwrPmAdvTableThe advanced performance monitoring measurements table. SEQUENCE OF MwrPmAdvEntry .1.3.6.1.4.1.7262.4.5.16.2.4 |
mwrPmAdvEntryThe advanced performance monitoring measurements table entries. MwrPmAdvEntry .1.3.6.1.4.1.7262.4.5.16.2.4.1 |
mwrPmAdvStatusIndexThe advanced performance monitoring measurements table index. Index 1 represents the radio port. Integer32 .1.3.6.1.4.1.7262.4.5.16.2.4.1.1 |
mwrPmAdvIntervalThe interval period of the row. Quarter means the 15 minutes interval and day means the 24 hours interval. PMIntervalType .1.3.6.1.4.1.7262.4.5.16.2.4.1.2 |
mwrPmAdvIntervalIDThe interval identifier of the row, from 1 (last quarter) to 16 (oldest quarter) for the 15-minute and from 1 (yesterday) to 4 (4 days ago) for the 24-hour. Value 0 can be used to retrieve current measurements, according to the requested granularity. Integer32 .1.3.6.1.4.1.7262.4.5.16.2.4.1.3 |
mwrPmAdvMeasSuspectAny problem that invalidates the measurement.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.16.2.4.1.4 |
mwrPmAdvMeasIntervalStatusAn indication if the interval is a valid measurement. When the system comes up, all the previous intervals are invalid.ro Enumeration .1.3.6.1.4.1.7262.4.5.16.2.4.1.5 |
mwrPmAdvMeasTimeLengthThe interval duration in seconds.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.4.1.6 |
mwrPmAdvTxCapPeakThe number of bits per second peak transmitted capacity during the time interval.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.4.1.7 |
mwrPmAdvTxCapRatioThe percentage of peak transmitted capacity referred to the total allowed capacity during the time interval.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.4.1.8 |
mwrPmAdvTxCapAvgThe number of bits per second average transmitted capacity during the time interval.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.4.1.9 |
mwrPmAdvTxCapAvgRatioThe percentage of average transmitted capacity during the time interval.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.4.1.10 |
mwrPmAdvTxCapHitsThe number of seconds where the transmitted capacity has overcome a configurable threshold during the time interval.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.4.1.11 |
mwrPmAdvRxCapPeakThe number of bits per second peak received capacity during the time interval.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.4.1.12 |
mwrPmAdvRxCapRatioThe percentage of peak received capacity referred to the total allowed capacity during the time interval.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.4.1.13 |
mwrPmAdvRxCapAvgThe number of bits per second average received capacity during the time interval.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.4.1.14 |
mwrPmAdvRxCapHitsThe number of seconds where the received capacity has overcome a configurable threshold during the time interval.ro Integer32 .1.3.6.1.4.1.7262.4.5.16.2.4.1.15 |
mwrPMNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.16.3 |
mwrUserMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.17 |
mwrUserConfiguration OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.17.1 |
mwrUserStatus OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.17.2 |
mwrUserSessionTableA table of user sessions SEQUENCE OF MwrUserSessionEntry .1.3.6.1.4.1.7262.4.5.17.2.1 |
mwrUserSessionEntryUser session entry MwrUserSessionEntry .1.3.6.1.4.1.7262.4.5.17.2.1.1 |
mwrUserIndexA unique value for each user. Enumeration .1.3.6.1.4.1.7262.4.5.17.2.1.1.1 |
mwrUserNameThe username of a management session using Telnet or HTTP. The session state variable must be checked to determine if the management session is currently in progress.ro DisplayString .1.3.6.1.4.1.7262.4.5.17.2.1.1.2 |
mwrUserConnectionTypeEither telnet, ssh, http or https. Ethernet connection may be through any physical port(s) dedicated to management of the equipment.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.4.5.17.2.1.1.3 |
mwrUserConnectionStateThe state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.ro Enumeration .1.3.6.1.4.1.7262.4.5.17.2.1.1.4 |
mwrUserNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.7262.4.5.17.3 |
mwrUserSessionThis notification is raised when a change in the state of user access is recognized, a new user has logged in or an existing user has logged out. NOTIFICATION-TYPE .1.3.6.1.4.1.7262.4.5.17.3.1 |
mwrUserLoginFailedThis notification is raised when a user has failed to login. NOTIFICATION-TYPE .1.3.6.1.4.1.7262.4.5.17.3.2 |
mwrUserAccountChangedThis notification is raised when a change in user account information in the system is detected. NOTIFICATION-TYPE .1.3.6.1.4.1.7262.4.5.17.3.3 |
mwrUserPasswordChangedThis notification is raised when a user password has changed. NOTIFICATION-TYPE .1.3.6.1.4.1.7262.4.5.17.3.4 |
mwrModIdentityThis specifies the contact information and the revision tracking information for the MIB module version. MODULE-IDENTITY .1.3.6.1.4.1.7262.4.5.1000 |