HORIZON-ODU-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for HORIZON-ODU-MIB.
496
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
496 total| Object Name |
|---|
coldStartA coldStart trap signifies that the sending protocol entity is reinitializing itself such that the agent's configuration or the protocol entity implementation may be altered. TRAP-TYPE .1.3.6.1.4.1.3727.20.20.3.1.11.0.0 |
linkDownA linkDown trap signifies that the sending protocol entity recognizes a failure in one of the communication links represented in the agent's configuration. TRAP-TYPE .1.3.6.1.4.1.3727.20.20.3.1.11.0.1 |
linkUpA linkUp trap signifies that the sending protocol entity recognizes that one of the communication links represented in the agent's configuration has come up. TRAP-TYPE .1.3.6.1.4.1.3727.20.20.3.1.11.0.2 |
horizonOdu OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2 |
SNMPv2-MIB Unknown .1.3.6.1.4.1.7262.2.2 |
hzOduSystem OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.1 |
hzOduSysGeneral OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.1.1 |
hzOduResetSystemWriting '1' to this object resets the NIC, Modem, and radio.rw INTEGER ( 0 .. 1 ) .1.3.6.1.4.1.7262.2.2.1.1.1 |
hzOduSaveMIBWriting '1' to this object save all MIB values. Note: If the horizon type is
'apng120' or 'apng170' and the radio band doesn't match the horizon type,
Mib can't be saved.rw Enumeration .1.3.6.1.4.1.7262.2.2.1.1.2 |
hzOduOperStatusThe current operational state of the system.
Testing indicates that no operational packets can be passed.ro Enumeration .1.3.6.1.4.1.7262.2.2.1.1.3 |
hzOduAirInterfaceEncryptionOBSOLETE. This enables encryption on the air interface.ro Enumeration .1.3.6.1.4.1.7262.2.2.1.1.4 |
hzOduSystemRedundancySets system redundancy on/off. If there are any radio failures then the system will automatically switch
to redundant system.rw Enumeration .1.3.6.1.4.1.7262.2.2.1.1.5 |
hzOduSysSpeed OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.1.2 |
hzOduSystemCurrentSpeedChanges the working speed of the horizon.
Writes are only valid if system is a FLEX. Due to backwards compatibility issue, 0 value should
be treated as 0 Mbps.rw INTEGER ( 0..1000 ) .1.3.6.1.4.1.7262.2.2.1.2.1 |
hzOduSystemLicensedSpeedIndicates the maximum speed that this system can operate at. Due to backwards compatibility issue, 0 value should
be treated as 0 Mbps.ro INTEGER ( 0..1000 ) .1.3.6.1.4.1.7262.2.2.1.2.2 |
hzOduSystemModeIndicates the specific type of system this is.ro Enumeration .1.3.6.1.4.1.7262.2.2.1.2.3 |
hzOduUpgradeLicensedSpeedEnter your apngFLEX key here along with the maximum speed for
that key to upgrade the FLEX system.
Format: [speed] [key]
Example: 50 abc123rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.1.2.4 |
hzOduInventory OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.1.3 |
hzOduHwInventory OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.1.3.1 |
hzOduUnitSerialNoA textual string containing Serial no of the Unit.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.1.3.1.1 |
hzOduUnitAssemblylNoA textual string containing assembly no of the Unit.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.1.3.1.2 |
hzOduIfSerialNoA textual string containing Serial no of the IF.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.1.3.1.3 |
hzOduIfAssemblylNoA textual string containing assembly no of the IF.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.1.3.1.4 |
hzOduRfSerialNoA textual string containing Serial no of the RF.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.1.3.1.5 |
hzOduRfAssemblylNoA textual string containing assembly no of the RF.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.1.3.1.6 |
hzOduNccSerialNoA textual string containing Serial no of the NCC.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.1.3.1.7 |
hzOduNccAssemblylNoA textual string containing assembly no of the NCC.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.1.3.1.8 |
hzOduDiplexerSerialNoA textual string containing Serial no of the Diplexer.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.1.3.1.9 |
hzOduDiplexerAssemblylNoA textual string containing assembly no of the Diplexer.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.1.3.1.10 |
hzOduSwInventory OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.1.3.2 |
hzOduSystemOmniVersionNoThe version number of the Omni.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.1.3.2.1 |
hzOduModemOmniVersionNoThe version number of the Modem FPGA.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.1.3.2.2 |
hzOduFrequencyFileVersionNoThe version number of the FrequencyFile.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.1.3.2.3 |
hzOduMibVersionNoThe version number of the MIB.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.1.3.2.4 |
hzOduAtpc OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.1.4 |
hzOduAtpcEnableIndicates whether Automatic Transmit Power Control (ATPC) is enabled.rw Enumeration .1.3.6.1.4.1.7262.2.2.1.4.1 |
hzOduAtpcCoordinatedPowerDbmThis defines the coordinated power level.
The value is multiplied by 10. e.g. A display
of 133 is actually 13.3 dBm.rw INTEGER .1.3.6.1.4.1.7262.2.2.1.4.2 |
hzOduAam OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.1.5 |
hzOduAamEnableIndicates whether Automatic Adaptive Modulation(AAM) is enabled.rw Enumeration .1.3.6.1.4.1.7262.2.2.1.5.1 |
hzOduPeerSysInfo OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.1.6 |
hzOduPeerMacAddressThe MAC Address of the peer network interface card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.1.6.1 |
hzOduPeerIpAddressThe IP Address of the peer network interface card.ro IpAddress .1.3.6.1.4.1.7262.2.2.1.6.2 |
hzOduPeerSubnetMaskThe subnet mask for the peer network interface card.ro IpAddress .1.3.6.1.4.1.7262.2.2.1.6.3 |
hzOduSysRedundancy OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.1.7 |
hzOduSystemRedundancyModeallows the user to set system redundancy mode:
[ off | primary-hsb-1wire | secondary-hsb-1wire | primary-hsb-2wire | secondary-hsb-2wire ]rw Enumeration .1.3.6.1.4.1.7262.2.2.1.7.1 |
hzOduSystemRedundancyOverrideAllows the user to override the active link. User can forces
the link to stay on either primary or secondary link.rw Enumeration .1.3.6.1.4.1.7262.2.2.1.7.2 |
hzOduSystemRedundancyLinkStatusIndicates the redundancy link status.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.1.7.3 |
hzOduSystemRedundancyStandbyEnetStateAllows the user to set standby enet(port1) state.rw Enumeration .1.3.6.1.4.1.7262.2.2.1.7.4 |
hzOduSystemRedundancyStateSwitchAllows the user to switch redundancy state.rw Enumeration .1.3.6.1.4.1.7262.2.2.1.7.5 |
hzOduAuthentication OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.2 |
hzOduUniquePeerAuthenticationKeyThe serial number of the peer node that this node will communicate with.
This is only used when authentication mode is set to unique.rw DisplayString ( SIZE ( 0 .. 34 ) ) .1.3.6.1.4.1.7262.2.2.2.1 |
hzOduPeerDetectedSerialNumberThe serial number of the peer node that the system is presently communicating
with. This is only used when authentication is set to unique.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.2.2 |
hzOduAuthenticationModeThis sets the authentication mode for the system.If configured for unique
authentication, an horizon node only exchanges user traffic with one other
horizon node. The serial number is used in this case.
If configured for group authentication, an horizon node exchanges user
traffic with another horizon node of the same group and uses the
authentication keys.rw Enumeration .1.3.6.1.4.1.7262.2.2.2.3 |
hzOduAuthenticationFailureActionThis sets the authentication failure action for the system.
Block traffic will block all user traffic including remote
management access. Pass traffic will allow all user traffic
to be sent and recievedrw Enumeration .1.3.6.1.4.1.7262.2.2.2.4 |
hzOduPeerAuthenticationStatusSpecifies the current authentication status of the system.
Authenticated means authentication is on and the system
has been authenticated, notAuthenticated means authentication
is off or the system has not communicated yet with the other node,
explicit authentication failure means authentication is on and
authentication has failedro Enumeration .1.3.6.1.4.1.7262.2.2.2.5 |
hzOduNetworkManagement OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.3 |
hzOduMacAddressThe MAC Address of the network interface card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.3.1 |
hzOduNetworkManagementInterfaceDescribes the network management interface connection options.ro Enumeration .1.3.6.1.4.1.7262.2.2.3.2 |
hzOduIpAddressThe IP Address of the network interface card.ro IpAddress .1.3.6.1.4.1.7262.2.2.3.3 |
hzOduSubnetMaskThe subnet mask for the network interface card.ro IpAddress .1.3.6.1.4.1.7262.2.2.3.4 |
hzOduDefaultGatewayThe default gateway for the network interface cardro IpAddress .1.3.6.1.4.1.7262.2.2.3.5 |
hzOduTelnetAccessModeIndicates whether Telnet access is allowed.rw Enumeration .1.3.6.1.4.1.7262.2.2.3.6 |
hzOduSshAccessModeIndicates whether ssh access is allowed.rw Enumeration .1.3.6.1.4.1.7262.2.2.3.7 |
hzOduVlanTagEnableIndicates whether VLAN tagging is enabled.rw Enumeration .1.3.6.1.4.1.7262.2.2.3.8 |
hzOduVlanTagIdrw INTEGER .1.3.6.1.4.1.7262.2.2.3.9 |
hzOduVlanTagPriorityrw INTEGER .1.3.6.1.4.1.7262.2.2.3.10 |
hzOduNetworkInterface OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.4 |
hzOduEnetPort1 OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.4.1 |
hzOduEnetPort1DescriptionDescribes the functionality of the port1ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.4.1.1 |
hzOduEnetPort1Config OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.4.1.2 |
hzOduEnetPort1AutoNegotiationport1 Turns auto-negotiation on or off. Turning off results in
the interface defaulting to 100BaseT, Full Duplex.rw Enumeration .1.3.6.1.4.1.7262.2.2.4.1.2.1 |
hzOduEnetPort1SpeedConfigure the port1 interface speed .rw Enumeration .1.3.6.1.4.1.7262.2.2.4.1.2.2 |
hzOduEnetPort1DuplexConfigure the port1 interface duplex.ro Enumeration .1.3.6.1.4.1.7262.2.2.4.1.2.3 |
hzOduEnetPort1MediaConfigure the port1 interface media.rw Enumeration .1.3.6.1.4.1.7262.2.2.4.1.2.4 |
hzOduEnetPort1AdminStateConfigure the port1 interface media.ro Enumeration .1.3.6.1.4.1.7262.2.2.4.1.2.5 |
hzOduEnetPort1OpticalTransceiverStateWhen it is on, optical transmitter for port1 is enabled. Otherwise
optical transmitter is disabled.rw Enumeration .1.3.6.1.4.1.7262.2.2.4.1.2.6 |
hzOduEnetPort1PauseFrameEnableWhen PAUSE is enabled, port1 pause frames can be generated by the
system and the pause frames will flow toward the link partner
on the network. When PAUSE is not enabled,
no pause frames will be generated by the system.rw Enumeration .1.3.6.1.4.1.7262.2.2.4.1.2.7 |
hzOduEnetPort1MaxFrameSizeFor port1 the default maximum frame size is 1600 bytes. The settable
maximum frame size must be a multiple of 128. If the chosen
maximum frame size is not a multiple of 128, its closest
number which is a multiple of 128 is actually used. The
settable lowest maximum frame size is 1664, and the settable
highest maximum frame size is 9600. If the chosen maximum
frame size is out of this range, the default maximum frame
size of 1600 is used.rw INTEGER ( 1600..9600 ) .1.3.6.1.4.1.7262.2.2.4.1.2.8 |
hzOduEnetPort1DroppedEnetFramesThresholdParametersA read-write string: The threshold, in percent, and the number of seconds that it must exceed this threshold are programmed by the user. An example of the format of the string is as follows: '70 10'. The first parameter is the percentage of frames that are dropped, the second is the time in seconds that the threshold must be exceeded. The single quote marks i.e. ' ' are not used in the command.rw DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.2.2.4.1.2.9 |
hzOduEnetPort1BandwidthUtilizationThresholdParametersA read-write string: The percentage of available bandwidth threshold and the number of seconds that it must exceed this threshold are programmed by the user. An example of the format of the string is as follows: '70 10'. The first parameter is the threshold point in percent, the number of seconds that the threshold must be exceeded. The single quote marks i.e. ' ' are not used in the command.rw DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.2.2.4.1.2.10 |
hzOduEnetPort1Status OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.4.1.3 |
hzOduEnetPort1LinkStatusIndicates the port1 link status.ro Enumeration .1.3.6.1.4.1.7262.2.2.4.1.3.1 |
hzOduEnetPort1AutoNegotiationStatusIndicates the port1 AutoNegotiation status.ro Enumeration .1.3.6.1.4.1.7262.2.2.4.1.3.2 |
hzOduEnetPort1SpeedStatusIndicates the port1 interface speed status.ro Enumeration .1.3.6.1.4.1.7262.2.2.4.1.3.3 |
hzOduEnetPort1DuplexStatusIndicates the port1 interface duplex status.ro Enumeration .1.3.6.1.4.1.7262.2.2.4.1.3.4 |
hzOduEnetPort1MediaStatusIndicates the port1 interface media status.ro Enumeration .1.3.6.1.4.1.7262.2.2.4.1.3.5 |
hzOduEnetPort1Stats OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.4.1.4 |
hzOduEnetPort1TxFramesThe current count of port1 frames sent.ro Counter .1.3.6.1.4.1.7262.2.2.4.1.4.1 |
hzOduEnetPort1TxBytesThe current count of port1 bytes sent.ro Counter .1.3.6.1.4.1.7262.2.2.4.1.4.2 |
hzOduEnetPort1RxFramesThe current count of port1 frames received.ro Counter .1.3.6.1.4.1.7262.2.2.4.1.4.3 |
hzOduEnetPort1RxBytesThe current count of port1 bytes received.ro Counter .1.3.6.1.4.1.7262.2.2.4.1.4.4 |
hzOduEnetPort1RxFramesInErrorThe current count of port1 frames received in error.ro Counter .1.3.6.1.4.1.7262.2.2.4.1.4.5 |
hzOduEnetPort1RxFramesCRCErrorThe current count of CRC error frames received for port1.ro Counter .1.3.6.1.4.1.7262.2.2.4.1.4.6 |
hzOduEnetPort1BWUtilizationThe carried load over link capacity for port1.ro INTEGER .1.3.6.1.4.1.7262.2.2.4.1.4.7 |
hzOduEnetPort1IngressDataRateThe data rate coming into the ethernet for port1.
The data rate you see is multiplied by 100. e.g. A display
of 1530 is actually 15.30 Mpbsro INTEGER .1.3.6.1.4.1.7262.2.2.4.1.4.8 |
hzOduEnetPort1EgressDataRateThe data rate going out of the ethernet for port1.
The data rate you see is multiplied by 100. e.g. A display
of 1530 is actually 15.30 Mpbs.ro INTEGER .1.3.6.1.4.1.7262.2.2.4.1.4.9 |
hzOduEnetPort1FramesInQueue1The current count of port1 frames passed through queue 1.ro Counter .1.3.6.1.4.1.7262.2.2.4.1.4.10 |
hzOduEnetPort1FramesInQueue2The current count of port1 frames passed through queue 2.ro Counter .1.3.6.1.4.1.7262.2.2.4.1.4.11 |
hzOduEnetPort1FramesInQueue3The current count of NIC frames passed through queue 3.ro Counter .1.3.6.1.4.1.7262.2.2.4.1.4.12 |
hzOduEnetPort1FramesInQueue4The current count of NIC frames passed through queue 4.ro Counter .1.3.6.1.4.1.7262.2.2.4.1.4.13 |
hzOduEnetPort1FramesInQueue1DiscardedThe current count of NIC frames received in queue 2 that
were discarded, but due to an error. One possible reason
is lack of buffer space.ro Counter .1.3.6.1.4.1.7262.2.2.4.1.4.14 |
hzOduEnetPort1FramesInQueue2DiscardedThe current count of port1 frames received in queue 2 that
were discarded, but due to an error. One possible reason
is lack of buffer space.ro Counter .1.3.6.1.4.1.7262.2.2.4.1.4.15 |
hzOduEnetPort1FramesInQueue3DiscardedThe current count of port1 frames received in queue 3 that
were discarded, but due to an error. One possible reason
is lack of buffer space.ro Counter .1.3.6.1.4.1.7262.2.2.4.1.4.16 |
hzOduEnetPort1FramesInQueue4DiscardedThe current count of port1 frames received in queue 4 that
were discarded, but due to an error. One possible reason
is lack of buffer space.ro Counter .1.3.6.1.4.1.7262.2.2.4.1.4.17 |
hzOduEnetPort2 OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.4.2 |
hzOduEnetPort2DescriptionDescribes the functionality of the port2ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.4.2.1 |
hzOduEnetPort2Config OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.4.2.2 |
hzOduEnetPort2AutoNegotiationport1 Turns auto-negotiation on or off. Turning off results in
the interface defaulting to 100BaseT, Full Duplex.rw Enumeration .1.3.6.1.4.1.7262.2.2.4.2.2.1 |
hzOduEnetPort2SpeedConfigure the port1 interface speed .rw Enumeration .1.3.6.1.4.1.7262.2.2.4.2.2.2 |
hzOduEnetPort2DuplexConfigure the port1 interface duplex.ro Enumeration .1.3.6.1.4.1.7262.2.2.4.2.2.3 |
hzOduEnetPort2AdminStateConfigure the port2 shutdown media.ro Enumeration .1.3.6.1.4.1.7262.2.2.4.2.2.4 |
hzOduEnetPort2Status OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.4.2.3 |
hzOduEnetPort2LinkStatusIndicates the Port2 link status.ro Enumeration .1.3.6.1.4.1.7262.2.2.4.2.3.1 |
hzOduEnetPort2AutoNegotiationStatusIndicates the Port2 AutoNegotiation status.ro Enumeration .1.3.6.1.4.1.7262.2.2.4.2.3.2 |
hzOduEnetPort2SpeedStatusIndicates the Port2 interface speed status.ro Enumeration .1.3.6.1.4.1.7262.2.2.4.2.3.3 |
hzOduEnetPort2DuplexStatusIndicates the Port2 interface duplex status.ro Enumeration .1.3.6.1.4.1.7262.2.2.4.2.3.4 |
hzOduEnetPort2MediaStatusIndicates the port1 interface media status.ro Enumeration .1.3.6.1.4.1.7262.2.2.4.2.3.5 |
hzOduEnetPort2Stats OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.4.2.4 |
hzOduEnetPort2TxFramesThe current count of Port2 frames sent.ro Counter .1.3.6.1.4.1.7262.2.2.4.2.4.1 |
hzOduEnetPort2TxBytesThe current count of Port2 bytes sent.ro Counter .1.3.6.1.4.1.7262.2.2.4.2.4.2 |
hzOduEnetPort2RxFramesThe current count of Port2 frames received.ro Counter .1.3.6.1.4.1.7262.2.2.4.2.4.3 |
hzOduEnetPort2RxBytesThe current count of Port2 bytes received.ro Counter .1.3.6.1.4.1.7262.2.2.4.2.4.4 |
hzOduEnetPort2RxFramesInErrorThe current count of Port2 frames received in error.ro Counter .1.3.6.1.4.1.7262.2.2.4.2.4.5 |
hzOduEnetPort2RxFramesCrcErrorThe current count of CRC error frames received for Port2.ro Counter .1.3.6.1.4.1.7262.2.2.4.2.4.6 |
hzOduWirelessInterface OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.5 |
hzOduWirelessPort1 OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.5.1 |
hzOduWirelessPort1DescriptionDescribes the functionality of the Wireless Interface1ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.5.1.1 |
hzOduModem1 OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.5.1.2 |
hzOduModem1AdminStatusThe current admin state of the interface. Testing
indicates that no operational packets can be passed.ro Enumeration .1.3.6.1.4.1.7262.2.2.5.1.2.1 |
hzOduModem1OperStatusThe current operational state of the interface. Testing
indicates that no operational packets can be passed.ro Enumeration .1.3.6.1.4.1.7262.2.2.5.1.2.2 |
hzOduModem1ResetWriting 1 to this object causes the modem card to be reset.
All other values are not recognized. This variable always
reads back as 0. mdmOperStatus should be polled by the
user after this object is written to, to verify that the
modem card has been reset. Not applicable in this releaserw INTEGER ( 0 .. 1 ) .1.3.6.1.4.1.7262.2.2.5.1.2.3 |
hzOduModem1ChannelizedRSLAn estimate of the modem's channelized RSL. Divide the value by 10 to get the actual RSL valuero INTEGER .1.3.6.1.4.1.7262.2.2.5.1.2.4 |
hzOduModem1ModulationTypeThe modulation type of the modem, distinguished according
to the physical/link protocol.ro Enumeration .1.3.6.1.4.1.7262.2.2.5.1.2.5 |
hzOduModem1CurrentRxSpeedAn estimate of the modem's current Rx bandwidth in bits per
second. Divide the value by 10000 to get the actual data rate in Mbpsro INTEGER .1.3.6.1.4.1.7262.2.2.5.1.2.6 |
hzOduModem1CurrentTxSpeedAn estimate of the modem's current Tx bandwidth in bits per
second. Divide the value by 10000 to get the actual data rate in Mbpsro INTEGER .1.3.6.1.4.1.7262.2.2.5.1.2.7 |
hzOduModem1SNRSNR value in dB. Divide the value by 10 to get the actual SNR.ro INTEGER .1.3.6.1.4.1.7262.2.2.5.1.2.8 |
hzOduModem1EbToNoiseRatioThe ratio of the modem Estimated Energy per information bit to Noise power spectral density.
Divide the value by 10 to get the actual EbToNoiseRatioro INTEGER .1.3.6.1.4.1.7262.2.2.5.1.2.9 |
hzOduModem1EqualizerStressIndicates the average magnitude of all the equalizer taps to provide a measure of how hard the equalizer is working.ro INTEGER .1.3.6.1.4.1.7262.2.2.5.1.2.10 |
hzOduModem1SNRThresholdParametersA read-write stringrw DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.2.2.5.1.2.11 |
hzOduModem1ChannelizedRslBelowThresholdParametersA read-write string: The threshold in dBm and the number of seconds threshold are programmed by the user. An example of the format of the string is as follows: '-75 10'. The first parameter power level in dBm, the second is the time in seconds that the threshold must be exceeded. In this example the threshold -75 dBm and the time is set to 10 seconds. The single quote marks i.e. ' ' are not used in the command.rw DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.2.2.5.1.2.12 |
hzOduModem1LastChangeThe value of sysUpTime at the time the modem entered its
current operational state. If the current state was
entered prior to the last re-initialization of the local
network management subsystem, then this object contains
a zero value.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.7262.2.2.5.1.2.13 |
hzOduModem1ChannelizedRSLUnsignedIntAn estimate of the modem's channelized RSL in dBm. The number is divided by 10. e.g. -432 is actually -43.2dBm.
Object provided mainly to accomodate plotting of negative RSL values which is not supported in some EMS (Ex: CastleRock).
Please use 'hzOduModem1ChannelizedRSL' object if your EMS supports plotting of -ve integer.ro INTEGER .1.3.6.1.4.1.7262.2.2.5.1.2.14 |
hzOduModem1Statistics OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.5.1.2.15 |
hzOduModem1TxFramesThe current count of Modem frames sent.ro Counter .1.3.6.1.4.1.7262.2.2.5.1.2.15.1 |
hzOduModem1RxFramesOKThe current count of Modem frames received.ro Counter .1.3.6.1.4.1.7262.2.2.5.1.2.15.2 |
hzOduModem1RxFramesErrorThe current count of Modem frames received in error.ro Counter .1.3.6.1.4.1.7262.2.2.5.1.2.15.3 |
hzOduModem1RxFramesQueueDiscardedThe current count of Modem frames in the queue that were discarded.ro Counter .1.3.6.1.4.1.7262.2.2.5.1.2.15.4 |
hzOduModem1TxBlocksThe current count of Modem blocks transmitted.ro Counter .1.3.6.1.4.1.7262.2.2.5.1.2.15.5 |
hzOduModem1RxBlocksOKThe current count of Modem blocks received.ro Counter .1.3.6.1.4.1.7262.2.2.5.1.2.15.6 |
hzOduModem1RxBlocksErrorThe current count of Modem blocks received in error.ro Counter .1.3.6.1.4.1.7262.2.2.5.1.2.15.7 |
hzOduRadio1 OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.5.1.3 |
hzOduRadio1OperStatusThe current operational state of the interface. Testing
indicates that no operational packets can be passed. Testing
also indicates that a firmware upgrade may be in progressro Enumeration .1.3.6.1.4.1.7262.2.2.5.1.3.1 |
hzOduRadio1TransmitPowerDbmThis defines the transmit level of the radio.
If ATPC is enabled, you can't change the transmit power.
The power you see is divided by 10. e.g. A display
of 133 is actually 13.3 dBm.
If the radio is operational and not muted, it is the
current transmitting power.
If the radio is operational and muted, it is the
programmed transmitting power, and will transmit at
this level when the radio is un-muted.
If the radio is not operational it is the programmed
transmitting power, and will transmit at this level
when the radio is operational and not muted.
If the radio does not have transmit calibration tables
programmed into its EEPROM, this transmit power level
cannot be used as it is not possible to accurately
calculate the actual transmit level. In this case this
object will return -99.rw INTEGER .1.3.6.1.4.1.7262.2.2.5.1.3.2 |
hzOduRadio1ProgrammedAntennaDiameterThis defines the diameter of the antenna used by the system represented in inches.rw Enumeration .1.3.6.1.4.1.7262.2.2.5.1.3.3 |
hzOduRadio1PowerOptionThis indicates the power option of the radio: normal or high power.ro Enumeration .1.3.6.1.4.1.7262.2.2.5.1.3.4 |
hzOduRadio1TxStateThis indicates the power option of the radio: normal or high power.ro Enumeration .1.3.6.1.4.1.7262.2.2.5.1.3.5 |
hzOduRadio1TemperatureThe Radio temperature in degree Centigrade. The actual temperature is got by dividing the number by 10. e.g. -432 is actually -43.2 degree centigrade.ro INTEGER .1.3.6.1.4.1.7262.2.2.5.1.3.6 |
hzOduFrequencies OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.6 |
hzOduRadioBandThe radio frequency standard used in the system.
Frequency bands are divided into sub bands.
ie FCC 23 Ghz Band is comprised of fcc23a, fcc23b, fcc23c and
fcc23d which make up the entire FCC23 bandrw Enumeration .1.3.6.1.4.1.7262.2.2.6.1 |
hzOduFreqGroupSelectedThe frequency group selected for the system.
The frequency subbands are divided into frequency groups txHigh
and txLow. An horizon system must have one node configured to
txLow and the other node configure to txHighrw Enumeration .1.3.6.1.4.1.7262.2.2.6.2 |
hzOduTxHighFreqTableA table of txHigh frequency settings for the system SEQUENCE OF HzOduTxHighFreqEntry .1.3.6.1.4.1.7262.2.2.6.3 |
hzOduTxHighFreqEntryA txHighFrequency entry containing all the frequency values HzOduTxHighFreqEntry .1.3.6.1.4.1.7262.2.2.6.3.1 |
hzOduTxHighFreqIndexA unique value for each frequency channel.ro INTEGER .1.3.6.1.4.1.7262.2.2.6.3.1.1 |
hzOduTxHighFreqChannelIndexThe channel index for the frequency.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.6.3.1.2 |
hzOduTxHighFreqTransmitRfFrequencyThe RF TX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.2.2.6.3.1.3 |
hzOduTxHighFreqReceiveRfFrequencyThe RF RX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.2.2.6.3.1.4 |
hzOduTxHighFreqProgrammedSpecifies the operating frequency channel for the modem.
***Only 1 index may be selected in a 1 modem system.rw Enumeration .1.3.6.1.4.1.7262.2.2.6.3.1.5 |
hzOduTxLowFreqTableA table of txLow frequency settings for the system SEQUENCE OF HzOduTxLowFreqEntry .1.3.6.1.4.1.7262.2.2.6.4 |
hzOduTxLowFreqEntryA hzOduTxLowFrequeny entry containing the frequency values
for a specific index HzOduTxLowFreqEntry .1.3.6.1.4.1.7262.2.2.6.4.1 |
hzOduTxLowFreqIndexA unique value for each frequency channel.ro INTEGER .1.3.6.1.4.1.7262.2.2.6.4.1.1 |
hzOduTxLowFreqChannelIndexThe channel index for the frequency.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.6.4.1.2 |
hzOduTxLowFreqTransmitRfFrequencyThe RF TX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.2.2.6.4.1.3 |
hzOduTxLowFreqReceiveRfFrequencyThe RF RX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.2.2.6.4.1.4 |
hzOduTxLowFreqProgrammedSpecifies the operating frequency channel for the modem.
***Only 1 index may be selected in a 1 modem system.rw Enumeration .1.3.6.1.4.1.7262.2.2.6.4.1.5 |
hzOduProgrammedFrequency OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.6.5 |
hzOduProgrammedFrequencyChannelThe channel that has been programmed into the system.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.6.5.1 |
hzOduProgrammedFrequencyTxRfThe programmed RF TX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.2.2.6.5.2 |
hzOduProgrammedFrequencyRxRfThe RF RX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.2.2.6.5.3 |
hzOduCalendar OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.7 |
hzOduDateA string in the format as follows:
XX/YY/ZZ
Where XX = day of month (range 01 to 31)
YY = month of year(range 01 to 12)
ZZ = year (range 01 - 99)ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.7.1 |
hzOduTimeA string in the format as follows:
aa:bb:cc:dd
Where aa = hour of day ( range 00 to 23 )
bb = minute of hour ( range 00 to 59 )
cc = second of minute( range 00 to 59 )
dd = hundredths of second (range 00 to 99)ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.7.2 |
hzOduAlarms OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.8 |
hzOduClearAlarmCountersClears the alarm counters for the specified grouprw Enumeration .1.3.6.1.4.1.7262.2.2.8.1 |
hzOduSystemAlarms OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.8.2 |
hzOduExplicitAuthenticationFailureAuthentication of the peer horizon node has failed. The severity is critical, the probable cause is an incorrect authentication configuration on horizon faulty cable between the modem and radio, and recommended course of action is to check both ends of the link.ro Enumeration .1.3.6.1.4.1.7262.2.2.8.2.1 |
hzOduExplicitAuthenticationFailureCountIndicates the number of times explicit authentication has failed.ro Counter .1.3.6.1.4.1.7262.2.2.8.2.2 |
hzOduAamConfigMismatchIn the near end Automatic Adaptive Modulation(AAM) feature set to on and in peer it is set to offro Enumeration .1.3.6.1.4.1.7262.2.2.8.2.3 |
hzOduAamConfigMismatchCountIndicates the approximate number of seconds AAMConfigMismatch alarm has been active.ro Counter .1.3.6.1.4.1.7262.2.2.8.2.4 |
hzOduAamActiveIndicates aam is active and system running on lowest modulationro Enumeration .1.3.6.1.4.1.7262.2.2.8.2.5 |
hzOduAamActiveCountIndicates the approximate number of seconds AAMActive alarm has been active.ro Counter .1.3.6.1.4.1.7262.2.2.8.2.6 |
hzOduAtpcConfigMismatchIn the near end Automatic Transmit Power Control(ATPC) feature set to on and in peer it is set to offro Enumeration .1.3.6.1.4.1.7262.2.2.8.2.7 |
hzOduAtpcConfigMismatchCountIndicates the approximate number of seconds AtpcConfigMismatch alarm has been activero Counter .1.3.6.1.4.1.7262.2.2.8.2.8 |
hzOduSntpServerUnavailableAlarmAll of the SNTP servers are not available.ro Enumeration .1.3.6.1.4.1.7262.2.2.8.2.9 |
hzOduSntpServerUnavailableAlarmCountIndicates how long in seconds all of the SNTP servers are not available.ro Counter .1.3.6.1.4.1.7262.2.2.8.2.10 |
hzOduFrequencyFileInvalidExecuting frequency file is valid or notro Enumeration .1.3.6.1.4.1.7262.2.2.8.2.11 |
hzOduFrequencyFileInvalidCountIndicates the time (in secs) since this alarm exist.ro Counter .1.3.6.1.4.1.7262.2.2.8.2.12 |
hzOduAtpcAutoDisabledIndicates the ATPC set to off and system transmit at coordinated power.ro Enumeration .1.3.6.1.4.1.7262.2.2.8.2.13 |
hzOduAtpcAutoDisabledCountIndicates the time (in secs) since this alarm exist.ro Counter .1.3.6.1.4.1.7262.2.2.8.2.14 |
hzOduPartnerRedundancyModeMismatchIndicates partner redundancy mode mismatches.ro Enumeration .1.3.6.1.4.1.7262.2.2.8.2.15 |
hzOduPartnerRedundancyModeMismatchCountIndicates the time (in secs) since this alarm exist.ro Counter .1.3.6.1.4.1.7262.2.2.8.2.16 |
hzOduPartnerConfigurationMismatchIndicates partner configuration mismatches.ro Enumeration .1.3.6.1.4.1.7262.2.2.8.2.17 |
hzOduPartnerConfigurationMismatchCountIndicates the time (in secs) since this alarm exist.ro Counter .1.3.6.1.4.1.7262.2.2.8.2.18 |
hzOduHsbActiveOnSecondaryIndicates the hsb active link is on secondary.ro Enumeration .1.3.6.1.4.1.7262.2.2.8.2.19 |
hzOduHsbActiveOnSecondaryCountIndicates the time (in secs) since this alarm exist.ro Counter .1.3.6.1.4.1.7262.2.2.8.2.20 |
hzOduHsbOverrideByUserIndicates the hsb mode is overrided by user.ro Enumeration .1.3.6.1.4.1.7262.2.2.8.2.21 |
hzOduHsbOverrideByUserCountIndicates the time (in secs) since this alarm exist.ro Counter .1.3.6.1.4.1.7262.2.2.8.2.22 |
hzOduHsbCrossLinkActiveIndicates the hsb cross link is active.ro Enumeration .1.3.6.1.4.1.7262.2.2.8.2.23 |
hzOduHsbCrossLinkActiveCountIndicates the time (in secs) since this alarm exist.ro Counter .1.3.6.1.4.1.7262.2.2.8.2.24 |
hzOduNetworkInterfaceAlarms OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.8.3 |
hzOduEnetPort1Alarms OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.8.3.1 |
hzOduEnetPort1DroppedEnetFramesThresholdExceededThe threshold for number of frames dropped has been exceeded. The threshold and the number of seconds that it must exceed this threshold are programmed by the user.ro Enumeration .1.3.6.1.4.1.7262.2.2.8.3.1.1 |
hzOduEnetPort1DroppedEnetFramesThresholdCountIndicates the approximate time, in seconds, that this alarm has been in the active statero Counter .1.3.6.1.4.1.7262.2.2.8.3.1.2 |
hzOduEnetPort1BandwidthUtilizationThresholdExceededThe threshold for the percentage of available bandwidth has been exceeded. The threshold and the number of seconds that it must exceed this threshold are programmed by the user.ro Enumeration .1.3.6.1.4.1.7262.2.2.8.3.1.3 |
hzOduEnetPort1BandwidthUtilizationThresholdCountIndicates the approximate time, in seconds, that this alarm has been in the active statero Counter .1.3.6.1.4.1.7262.2.2.8.3.1.4 |
hzOduEnetPort1RlsMismatchRLS configurations on the pair of systems are mismatched.ro Enumeration .1.3.6.1.4.1.7262.2.2.8.3.1.5 |
hzOduEnetPort1RlsMismatchCountIndicates the approximate time, in seconds, that this alarm has been in the active statero Counter .1.3.6.1.4.1.7262.2.2.8.3.1.6 |
hzOduEnetPort1RLSShutdownActivatedRLS shutdown is activated.ro Enumeration .1.3.6.1.4.1.7262.2.2.8.3.1.7 |
hzOduEnetPort1RLSShutdownActivatedCountIndicates the approximate time, in seconds, that this alarm has been in the active statero Counter .1.3.6.1.4.1.7262.2.2.8.3.1.8 |
hzOduEnetPort1EthernetLinkDownIndicates whether the Ethernet link is down or not. The severity is major, the probable cause is an incorrect configuration of the switch or router connected to horizon. The recommended course of action is to check the connection.ro Enumeration .1.3.6.1.4.1.7262.2.2.8.3.1.9 |
hzOduEnetPort1EthernetLinkDownActivatedCountIndicates the approximate time, in seconds, that this alarm has been in the active statero Counter .1.3.6.1.4.1.7262.2.2.8.3.1.10 |
hzOduEnetPort2Alarms OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.8.3.2 |
hzOduEnetPort2EthernetLinkDownIndicates whether the Ethernet link is down or not. The severity is major, the probable cause is an incorrect configuration of the switch or router connected to horizon. The recommended course of action is to check the connection.ro Enumeration .1.3.6.1.4.1.7262.2.2.8.3.2.1 |
hzOduEnetPort2EthernetLinkDownActivatedCountIndicates the approximate time, in seconds, that this alarm has been in the active statero Counter .1.3.6.1.4.1.7262.2.2.8.3.2.2 |
hzOduWirelessInterfaceAlarms OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.8.4 |
hzOduModem1Alarms OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.8.4.4 |
hzOduModem1RxLossOfSignalLoss of signal lock from the demodulator. The severity is critical, the probable cause is lost synchronization with the far end, and recommended course of action is to check the operational state of both ends of the link.ro Enumeration .1.3.6.1.4.1.7262.2.2.8.4.4.1 |
hzOduModem1RxLossOfSignalCountIndicates the approximate number of seconds that this alarm has been active.ro Counter .1.3.6.1.4.1.7262.2.2.8.4.4.2 |
hzOduModem1TxLossOfSyncLoss of sync bytes at the input of the modulator. The severity is critical, the probable cause is physical interference in the air link, and recommended course of action is to check the line of site between the horizon nodes.ro Enumeration .1.3.6.1.4.1.7262.2.2.8.4.4.3 |
hzOduModem1TxLossOfSyncCountIndicates the approximate number of seconds that this alarm has been active.ro Counter .1.3.6.1.4.1.7262.2.2.8.4.4.4 |
hzOduModem1SnrBelowThresholdThe demodulator SNR performance worse than programmed levels. The severity is major, the probable cause is physical interference in the air link path or misalignment of the radios or severe weather conditions, and recommended course of action is to check the line of site between the horizon nodes.ro Enumeration .1.3.6.1.4.1.7262.2.2.8.4.4.5 |
hzOduModem1SnrBelowThresholdCountIndicates the approximate number of seconds that this alarm has been active.ro Counter .1.3.6.1.4.1.7262.2.2.8.4.4.6 |
hzOduModem1EqualizerStressExceedThresholdEqualizer Stress measured within the demodulator exceeds the threshold value.ro Enumeration .1.3.6.1.4.1.7262.2.2.8.4.4.7 |
hzOduModem1EquilizerStressExceedThresholdCountIndicates the approximate number of seconds that this alarm has been active.ro Counter .1.3.6.1.4.1.7262.2.2.8.4.4.8 |
hzOduModem1HardwareFaultro Enumeration .1.3.6.1.4.1.7262.2.2.8.4.4.9 |
hzOduModem1HardwareFaultCountIndicates the approximate number of seconds that this alarm has been active.ro Counter .1.3.6.1.4.1.7262.2.2.8.4.4.10 |
hzOduModem1ProgrammingErrorEncountered some problem while programming the modem.ro Enumeration .1.3.6.1.4.1.7262.2.2.8.4.4.11 |
hzOduModem1ProgrammingErrorCountIndicates the approximate number of seconds that this alarm has been active.ro Counter .1.3.6.1.4.1.7262.2.2.8.4.4.12 |
hzOduRadio1Alarms OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.8.4.5 |
hzOduRadio1SynthLostLockLoss of signal lock from IF Synthesizer.ro Enumeration .1.3.6.1.4.1.7262.2.2.8.4.5.1 |
hzOduRadio1SynthLostLockCountIndicates the number of seconds that Loss of signal lock from IF Synthesizer.ro Counter .1.3.6.1.4.1.7262.2.2.8.4.5.2 |
hzOduRadio1TempCompCalTableNotAvailTemp comp table not available.ro Enumeration .1.3.6.1.4.1.7262.2.2.8.4.5.3 |
hzOduRadio1TempCompCalTableNotAvailCountIndicates the number of seconds that Temp comp table not available.ro Counter .1.3.6.1.4.1.7262.2.2.8.4.5.4 |
hzOduRadio1TxDetectorPwrBelowThreshTx power detector below threshold 1.ro Enumeration .1.3.6.1.4.1.7262.2.2.8.4.5.5 |
hzOduRadio1TxDetectorPwrBelowThreshCountIndicates the number of seconds that Tx power detector below threshold 1.ro Counter .1.3.6.1.4.1.7262.2.2.8.4.5.6 |
hzOduRadio1DrainCurrentOutOfLimitRadio current1 out of limits.ro Enumeration .1.3.6.1.4.1.7262.2.2.8.4.5.7 |
hzOduRadio1DrainCurrentOutOfLimitCountIndicates the number of seconds that Radio current1 out of limits.ro Counter .1.3.6.1.4.1.7262.2.2.8.4.5.8 |
hzOduRadio1TemperatureOutOfLimitRadio temperature out of limits.ro Enumeration .1.3.6.1.4.1.7262.2.2.8.4.5.9 |
hzOduRadio1TemperatureOutOfLimitCountIndicates the number of seconds that Radio temperature out of limits.ro Counter .1.3.6.1.4.1.7262.2.2.8.4.5.10 |
hzOduTraps OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.9 |
hzOduExplicitAuthenticationFailureV1TrapAuthentication of the peer horizon node has failed. The severity is critical, the probable cause is an incorrect authentication configuration on horizon faulty cable between the modem and radio, and recommended course of action is to check both ends of the link. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.3 |
hzOduExplicitAuthenticationFailureClearedV1TrapThe condition has cleared. The peer node is now authenticated. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.4 |
hzOduAamConfigMisMatchV1TrapAdaptive modulation configuration mismatch TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.5 |
hzOduAamConfigMisMatchClearV1TrapAdaptive modulation configuration mismatch cleared TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.6 |
hzOduAamActiveV1TrapAdaptive modulation on and system running on lowest modulation TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.7 |
hzOduAamActiveClearedV1TrapAdaptive modulation on system running on higher modulation TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.8 |
hzOduAtpcConfigMismatchV1TrapATPC is set to on at near end however in the far end it is set to off. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.9 |
hzOduAtpcConfigMismatchClearedV1TrapATPC configuration mismatch is cleared TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.10 |
hzOduSntpServersUnreachableV1TrapCan't reach any of the sntp servers TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.11 |
hzOduSntpServersUnreachableClearedV1TrapAt least one of SNTP servers is reachable TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.12 |
hzOduFrequencyFileInvalidV1TrapWhen the executing frequency file is invalid,
this trap is generated. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.13 |
hzOduEnetPort1DroppedFramesThresholdExceededV1TrapThe ethernet dropped frames threshold has been detected above its threshold value. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.14 |
hzOduEnetPort1DroppedFramesThresholdExceededClearedV1TrapThe condition has cleared.The ethernet dropped frames threshold is now below its threshold value. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.15 |
hzOduEnetPort1BwUtilizationThresholdExceededV1TrapThe ethernet bandwidth threshold has been detected above its threshold value. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.16 |
hzOduEnetPort1BwUtilizationThresholdExceededClearedV1TrapThe condition has cleared. The ethernet bandwidth threshold is now below its threshold value. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.17 |
hzOduEnetPort1RlsMismatchV1TrapRLS mismatch TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.18 |
hzOduEnetPort1RlsMismatchClearedV1TrapRLS mismatch cleared TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.19 |
hzOduEnetPort1RlsShutdownActivatedv1TrapRLS shutdown is activated TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.20 |
hzOduEnetPort1RlsShutdownActivatedClearedV1TrapRLS shutdown is not activated TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.21 |
hzOduModem1RxLossOfSignalLockV1TrapLoss of signal lock from the demodulator. The severity is critical, the probable cause is lost synchronization with the far end, and recommended course of action is to check the operational state of both ends of the link. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.22 |
hzOduModem1RxLossOfSignalLockClearedV1TrapThe condition has cleared. The demodulator is synchronized. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.23 |
hzOduModem1TxLossOfSyncV1TrapLoss of sync bytes at the input of the modulator. The severity is critical, the probable cause is physical
interference in the air link, and recommended course of action is to check the line of site between the horizon nodes. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.24 |
hzOduModem1TxLossOfSyncClearedV1TrapTx Loss of sync bytes cleared. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.25 |
hzOduModem1SnrBelowThresholdV1TrapThe demodulator SNR performance worse than programmed levels. The severity is major, the probable cause
is physical interference in the air link path or misalignment of the radios or severe weather conditions, and recommended course
of action is to check the line of site between the horizon nodes. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.26 |
hzOduModem1SnrBelowThresholdClearedV1TrapSNR performance back to normal. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.27 |
hzOduModem1EqualizerStressExceedThresholdV1TrapEqualizer Stress measured within the demodulator exceeds the threshold value. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.28 |
hzOduModem1EqualizerStressExceedThresholdClearedV1TrapEqualizer Stress measured within the demodulator is within the threshold value. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.29 |
hzOduEnetPort1ChannelizedRslBelowThresholdV1TrapThe RSL has been detected below its minimum threshold. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.30 |
hzOduEnetPort1ChannelizedRslBelowThresholdClearedV1TrapThe condition has cleared. RSL is now above its minimum threshold. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.31 |
hzOduModem1HardwareFaultV1TrapPower supply circuitry failed. Should be sent for diagnosis. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.32 |
hzOduModem1HardwareFaultClearedV1TrapPower supply circuitry is in good condition. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.33 |
hzOduModem1ProgrammingErrorV1TrapEncountered problem while programming modem. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.34 |
hzOduModem1ProgrammingErrorClearedrV1TrapProblem encountered while programming modem is gone. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.35 |
hzOduRadio1SynthLostLockV1TrapIF synth Lock is lost. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.36 |
hzOduRadio1SynthLostLockClearedV1TrapIF synth Lock is lost cleared. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.37 |
hzOduRadio1TempCompCalTableNotAvailableV1TrapTemp comp table not available. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.38 |
hzOduRadio1TempCompCalTableNotAvailableClearedV1TrapTemp comp table not available cleared. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.39 |
hzOduRadio1TxDetectorPwrBelowThreshV1TrapTx power detector below threshold. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.40 |
hzOduRadio1TxDetectorPwrBelowThreshClearedV1TrapTx power detector below threshold cleared. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.41 |
hzOduRadio1DrainCurrentOutOfLimitV1TrapRadio current out of limits. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.42 |
hzOduRadio1DrainCurrentOutOfLimitClearedV1TrapRadio current out of limits cleared. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.43 |
hzOduRadio1TemperatureOutOfLimitV1TrapRadio temperature out of limits. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.44 |
hzOduRadio1TemperatureOutOfLimitClearedV1TrapRadio temperature out of limits cleared. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.45 |
hzOduTtySessionCommencedV1TrapA person has successfully gained access to the ascii management port (telnet, local management port, or HTTP). The username is included in the Trap. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.46 |
hzOduTtySessionTerminatedV1TrapA person has logged out of an ascii management port (telnet, local management port, or HTTP). The username is included in the Trap. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.47 |
hzOduAtpcTxAtCoordinatedPwrV1TrapAtpc is enabled in the system and it is transmitting at maximum power. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.48 |
hzOduAtpcTxAtCoordinatedPwrClearedV1TrapAtpc is enabled in the system and it is back to regular power. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.49 |
hzOduPartnerRedundancyModeMismatchV1TrapHsb partner redundancy mode mismatch. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.50 |
hzOduPartnerRedundancyModeMismatchClearedV1TrapHsb partner redundancy mode mismatch is cleared. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.51 |
hzOduPartnerConfigurationMismatchV1TrapHsb partner configuration mismatch. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.52 |
hzOduPartnerConfigurationMismatchClearedV1TrapHsb partner configuration mismatch is cleared. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.53 |
hzOduHsbActiveOnSecondaryV1TrapHsb active on secondary. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.54 |
hzOduHsbActiveOnSecondaryClearedV1TrapHsb active on secondary is cleared. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.55 |
hzOduHsbOverrideByUserV1TrapHsb override by user. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.56 |
hzOduHsbOverrideByUserClearedV1TrapHsb active on secondary is cleared. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.57 |
hzOduHsbCrossLinkV1TrapHsb cross link by user. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.58 |
hzOduHsbCrossLinkClearedV1TrapHsb cross link is cleared. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.59 |
hzOduHsbActiveOnPrimaryV1TrapHsb active on primary. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.60 |
hzOduHsbActiveOnPrimaryClearedV1TrapHsb active on primary is cleared. TRAP-TYPE .1.3.6.1.4.1.7262.2.2.9.0.61 |
hzOduSnmpTrapHostTableTable containing SNMP trap host entries. SEQUENCE OF HzOduSnmpTrapHostEntry .1.3.6.1.4.1.7262.2.2.9.1 |
hzOduSnmpTrapHostEntryThe snmp trap host entry containing all the trap host information HzOduSnmpTrapHostEntry .1.3.6.1.4.1.7262.2.2.9.1.1 |
hzOduSnmpTrapHostIndexA unique value for each trap host.ro INTEGER .1.3.6.1.4.1.7262.2.2.9.1.1.1 |
hzOduSnmpTrapHostModeIndicates how the snmp trap host is obtained for the system.ro Enumeration .1.3.6.1.4.1.7262.2.2.9.1.1.2 |
hzOduSnmpTrapHostIpAddressIndicates snmp trap host IP address.ro IpAddress .1.3.6.1.4.1.7262.2.2.9.1.1.3 |
hzOduSnmpTrapHostCommunityNameThe community string name used in Traps.ro DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.2.2.9.1.1.4 |
hzOduSnmpTrapHostActivatedSpecifies whether traps are to be sent to this specific host or notro Enumeration .1.3.6.1.4.1.7262.2.2.9.1.1.5 |
hzOduSnmpV3TrapHostsTableTable containing snmp V3 trap host entries SEQUENCE OF HzOduSnmpV3TrapHostsEntry .1.3.6.1.4.1.7262.2.2.9.2 |
hzOduSnmpV3TrapHostsEntryContains the snmp v3 trap host information HzOduSnmpV3TrapHostsEntry .1.3.6.1.4.1.7262.2.2.9.2.1 |
hzOduSnmpV3TrapHostsIndexA unique value for each v3 trap host.ro INTEGER .1.3.6.1.4.1.7262.2.2.9.2.1.1 |
snmpV3TrapHostIpAddressIndicates snmp trap host IP address.ro IpAddress .1.3.6.1.4.1.7262.2.2.9.2.1.2 |
snmpV3TrapHostUserNameThe user name of the v3 trap host.ro DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.2.2.9.2.1.3 |
snmpV3TrapHostAuthProtocolThe authentication alogorithm used by the v3 trap host.ro Enumeration .1.3.6.1.4.1.7262.2.2.9.2.1.4 |
snmpV3TrapHostAuthPasswordThe authentication password of the v3 trap host.ro DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.2.2.9.2.1.5 |
snmpV3TrapHostPrivProtocolThe privacy encryiption alogorithm used by the v3 trap host.ro Enumeration .1.3.6.1.4.1.7262.2.2.9.2.1.6 |
snmpV3TrapHostPrivPasswordThe privacy password of the v3 trap host.ro DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.2.2.9.2.1.7 |
snmpV3TrapHostActivatedSpecifies whether a specific v3 trap host is allowed to access the systemro Enumeration .1.3.6.1.4.1.7262.2.2.9.2.1.8 |
hzOduColdStartTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.2.2.9.3 |
hzOduLinkDownTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.2.2.9.4 |
hzOduLinkUpTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.2.2.9.5 |
hzOduExplicitAuthenticationFailureTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.2.2.9.6 |
hzOduAamConfigMismatchTrapEnables or disables the aamConfigMismatch trap.rw Enumeration .1.3.6.1.4.1.7262.2.2.9.7 |
hzOduAamActiveTrapEnables or disables the aamActive trap.rw Enumeration .1.3.6.1.4.1.7262.2.2.9.8 |
hzOduAtpcConfigMismatchTrapEnables or disables the trap.rw Enumeration .1.3.6.1.4.1.7262.2.2.9.9 |
hzOduSntpServersUnreachableTrapEnables or disables the trap.rw Enumeration .1.3.6.1.4.1.7262.2.2.9.10 |
hzOduFrequencyFileInvalidTrapEnables or disables the trap.rw Enumeration .1.3.6.1.4.1.7262.2.2.9.11 |
hzOduEnetPort1DroppedFramesThresholdExceedTrapEnables or disables the trap. This trap, if enabled, will be sent when the dropped ethernet frames threshold is exceeded. If enabled, the system will send this trap to all trap hosts programmed in the system by the user.rw Enumeration .1.3.6.1.4.1.7262.2.2.9.12 |
hzOduEnetPort1BandwidthUtilizationThresholdExceedTrapEnables or disables the trap. This trap, if enabled, will be sent when the ethernet bandwidth utilization threshold is exceeded. If enabled, the system will send this trap to all trap hosts programmed in the system by the user.rw Enumeration .1.3.6.1.4.1.7262.2.2.9.13 |
hzOduEnetPort1RlsMismatchTrapEnables or disables the trap.rw Enumeration .1.3.6.1.4.1.7262.2.2.9.14 |
hzOduEnetPort1RLSShutdownActivatedTrapEnables or disables the trap.rw Enumeration .1.3.6.1.4.1.7262.2.2.9.15 |
hzOduModem1RxLossOfSignalLockTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.2.2.9.16 |
hzOduModem1TxLossOfSyncTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.2.2.9.17 |
hzOduModem1SnrBelowThresholdTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.2.2.9.18 |
hzOduModem1EqualizerStressExceedThresholdTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.2.2.9.19 |
hzOduModem1ChannelizedRslBelowThresholdTrapEnables or disables the trap. This trap, if enabled, will be sent when the radio receive signal level threshold is exceeded. If enabled, the system will send this trap to all trap hosts programmed in the system by the user.rw Enumeration .1.3.6.1.4.1.7262.2.2.9.20 |
hzOduModem1HardwareFaultTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.2.2.9.21 |
hzOduModem1ProgrammingErrorTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.2.2.9.22 |
hzOduRadio1SynthLostLockTrapEnables or disables the ifSythLostLock trap.rw Enumeration .1.3.6.1.4.1.7262.2.2.9.23 |
hzOduRadio1TempCompCalTableNotAvailTrapEnables or disables the tempCompCalTableNotAvailable trap.rw Enumeration .1.3.6.1.4.1.7262.2.2.9.24 |
hzOduRadio1TxDetectorPwrBelowThreshTrapEnables or disables the txDetectorPwrBelowThresh trap.rw Enumeration .1.3.6.1.4.1.7262.2.2.9.25 |
hzOduRadio1DrainCurrentOutOfLimitTrapEnables or disables the radioCurrentOutOfLimitTrap trap.rw Enumeration .1.3.6.1.4.1.7262.2.2.9.26 |
hzOduRadio1TemperatureOutOfLimitTrapEnables or disables the radioTemperatureOutOfLimitTrap trap.rw Enumeration .1.3.6.1.4.1.7262.2.2.9.27 |
hzOduTtyManagementSessionCommencedTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.2.2.9.28 |
hzOduTtyManagementSessionTerminatedTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.2.2.9.29 |
hzOduAtpcAutoDisabledTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.2.2.9.30 |
hzOduPartnerRedundancyModeMismatchTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.2.2.9.31 |
hzOduPartnerConfigurationMismatchTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.2.2.9.32 |
hzOduHsbActiveOnSecondaryTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.2.2.9.33 |
hzOduHsbOverrideByUserTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.2.2.9.34 |
hzOduHsbCrossLinkTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.2.2.9.35 |
hzOduHsbActiveOnPrimaryTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.2.2.9.36 |
hzOduSnmp OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.10 |
hzOduSnmpUserAccessSpecifies the user access to the system.If access is set to managers then only managers with there ip addresses set in snmpManagersTable will be able to gain snmp access to the system. If access is set to any then any manager will be able to gain snmp access to the systemro Enumeration .1.3.6.1.4.1.7262.2.2.10.1 |
hzOduSnmpManagerAnyCommunityNameThe community string name used by the 'any' manager.ro DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.2.2.10.2 |
hzOduSnmpSetRequestsIndicates whether SNMP SET requests are allowed.ro Enumeration .1.3.6.1.4.1.7262.2.2.10.3 |
hzOduSnmpManagersTableTable containing snmp manager entries SEQUENCE OF HzOduSnmpManagersEntry .1.3.6.1.4.1.7262.2.2.10.4 |
hzOduSnmpManagersEntryContains the snmp manager information HzOduSnmpManagersEntry .1.3.6.1.4.1.7262.2.2.10.4.1 |
hzOduSnmpManagersIndexA unique value for each manager.ro INTEGER .1.3.6.1.4.1.7262.2.2.10.4.1.1 |
hzOduSnmpManagerIpAddressThe IP address of the Manager.ro IpAddress .1.3.6.1.4.1.7262.2.2.10.4.1.2 |
hzOduSnmpManagerCommunityNameThe community string name used by the manager.ro DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.2.2.10.4.1.3 |
hzOduSnmpManagerActivatedSpecifies whether a specific manager is allowed to access the systemro Enumeration .1.3.6.1.4.1.7262.2.2.10.4.1.4 |
hzOduSnmpV3ManagersTableTable containing snmp V3 manager entries SEQUENCE OF HzOduSnmpV3ManagersEntry .1.3.6.1.4.1.7262.2.2.10.5 |
hzOduSnmpV3ManagersEntryContains the snmp v3 manager information HzOduSnmpV3ManagersEntry .1.3.6.1.4.1.7262.2.2.10.5.1 |
hzOduSnmpV3ManagersIndexA unique value for each v3 manager.ro INTEGER .1.3.6.1.4.1.7262.2.2.10.5.1.1 |
hzOduSnmpV3ManagerUserNameThe user name of the v3 Manager.ro DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.2.2.10.5.1.2 |
hzOduSnmpV3ManagerAuthProtocolThe authentication alogorithm used by the v3 manager.ro Enumeration .1.3.6.1.4.1.7262.2.2.10.5.1.3 |
hzOduSnmpV3ManagerAuthPasswordThe authentication password of the v3 Manager.ro DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.2.2.10.5.1.4 |
hzOduSnmpV3ManagerPrivProtocolThe privacy encryiption alogorithm used by the v3 manager.ro Enumeration .1.3.6.1.4.1.7262.2.2.10.5.1.5 |
hzOduSnmpV3ManagerPrivPasswordThe privacy password of the v3 Manager.ro DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.2.2.10.5.1.6 |
hzOduSnmpV3ManagerActivatedSpecifies whether a specific v3 manager is allowed to access the systemro Enumeration .1.3.6.1.4.1.7262.2.2.10.5.1.7 |
hzOduManagementSessions OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.11 |
hzOduTtySessionUser1 OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.11.1 |
hzOduTtySessionUser1NameThe username of a management session using Telnet or HTTP. The session state variable must be checked to determine if the management session is currently in progress.ro DisplayString ( SIZE ( 0 .. 32 ) ) .1.3.6.1.4.1.7262.2.2.11.1.1 |
hzOduTtySessionUser1ConnectionTypeThe physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.ro Enumeration .1.3.6.1.4.1.7262.2.2.11.1.2 |
hzOduTtySessionUser1StateThe state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.ro Enumeration .1.3.6.1.4.1.7262.2.2.11.1.3 |
hzOduTtySessionUser2 OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.11.2 |
hzOduTtySessionUser2NameThe username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system.ro DisplayString ( SIZE ( 0 .. 32 ) ) .1.3.6.1.4.1.7262.2.2.11.2.1 |
hzOduTtySessionUser2ConnectionTypeThe physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.ro Enumeration .1.3.6.1.4.1.7262.2.2.11.2.2 |
hzOduTtySessionUser2StateThe state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.ro Enumeration .1.3.6.1.4.1.7262.2.2.11.2.3 |
hzOduTtySessionUser3 OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.11.3 |
hzOduTtySessionUser3NameThe username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system.ro DisplayString ( SIZE ( 0 .. 32 ) ) .1.3.6.1.4.1.7262.2.2.11.3.1 |
hzOduTtySessionUser3ConnectionTypeThe physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.ro Enumeration .1.3.6.1.4.1.7262.2.2.11.3.2 |
hzOduTtySessionUser3StateThe state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.ro Enumeration .1.3.6.1.4.1.7262.2.2.11.3.3 |
hzOduTtySessionUser4 OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.11.4 |
hzOduTtySessionUser4NameThe username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system.ro DisplayString ( SIZE ( 0 .. 32 ) ) .1.3.6.1.4.1.7262.2.2.11.4.1 |
hzOduTtySessionUser4ConnectionTypeThe physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.ro Enumeration .1.3.6.1.4.1.7262.2.2.11.4.2 |
hzOduTtySessionUser4StateThe state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.ro Enumeration .1.3.6.1.4.1.7262.2.2.11.4.3 |
hzOduTtySessionUser5 OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.11.5 |
hzOduTtySessionUser5NameThe username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system.ro DisplayString ( SIZE ( 0 .. 32 ) ) .1.3.6.1.4.1.7262.2.2.11.5.1 |
hzOduTtySessionUser5ConnectionTypeThe physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.ro Enumeration .1.3.6.1.4.1.7262.2.2.11.5.2 |
hzOduTtySessionUser5StateThe state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.ro Enumeration .1.3.6.1.4.1.7262.2.2.11.5.3 |
hzOduTtySessionUser6 OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.11.6 |
hzOduTtySessionUser6NameThe username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system.ro DisplayString ( SIZE ( 0 .. 32 ) ) .1.3.6.1.4.1.7262.2.2.11.6.1 |
hzOduTtySessionUser6ConnectionTypeThe physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.ro Enumeration .1.3.6.1.4.1.7262.2.2.11.6.2 |
hzOduTtySessionUser6StateThe state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.ro Enumeration .1.3.6.1.4.1.7262.2.2.11.6.3 |
hzOduSessionUserInformation OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.11.7 |
hzOduTtySessionUserNameNOT IMPLEMENTED. Object type placeholder for username string for SNMP traps. The username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system.ro DisplayString ( SIZE ( 0 .. 32 ) ) .1.3.6.1.4.1.7262.2.2.11.7.1 |
hzOduTtySessionUserConnectionTypeNOT IMPLEMENTED. Object type placeholder for connection type for SNMP traps. The physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.ro Enumeration .1.3.6.1.4.1.7262.2.2.11.7.2 |
hzOduHttp OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.12 |
hzOduHttpEnableIndicates whether HTTP is enabled.rw Enumeration .1.3.6.1.4.1.7262.2.2.12.1 |
hzOduHttpSecure OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.12.2 |
hzOduHttpSecureCertificateStatusReturns the HTTPS certificate statusro DisplayString ( SIZE ( 0 .. 100 ) ) .1.3.6.1.4.1.7262.2.2.12.2.1 |
hzOduHttpSecureAccessForAdminUsersthe HTTPS access requirement for Admin user group.rw Enumeration .1.3.6.1.4.1.7262.2.2.12.2.2 |
hzOduHttpSecureAccessForNocUsersthe HTTPS access requirement for Noc user group.rw Enumeration .1.3.6.1.4.1.7262.2.2.12.2.3 |
hzOduHttpSecureAccessForSuperUsersthe HTTPS access requirement for Super user group.rw Enumeration .1.3.6.1.4.1.7262.2.2.12.2.4 |
hzOduQos OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.13 |
hzOduQosEnableIndicates whether QOS is enabled.rw Enumeration .1.3.6.1.4.1.7262.2.2.13.1 |
hzOduCosTypeIndicates the class of service tag type. Based on the setting
Horizon will use the CoS value in the VLAN tag, or Q-in-Q inner
VLAN tag, Q-in-Q outer VLAN tag, or DSCP tag.rw Enumeration .1.3.6.1.4.1.7262.2.2.13.2 |
hzOduCoSQinQiTagSets the value of the Q-in-Q inner tag. This
tag is also used to classify the non-Q-in-Q VLAN. Default value is 0x8100.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.13.3 |
hzOduCoSQinQoTagSets the value of the Q-in-Q outer VLAN tag. Default value is 0x8100.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.13.4 |
hzOduCosQueueMappingUser queue assignments for CoS values 0 to 7.
There are 4 coS queues. Their corresponding
queue numbers are 1,2, 3, where 1 is the lowest priority queue and
4 is the highest priority queue.
CoS to queue mapping example: 1 1 2 2 3 3 4 4.rw DisplayString ( SIZE ( 15 .. 32 ) ) .1.3.6.1.4.1.7262.2.2.13.5 |
hzOduCosExpediteQueueThis sets the user queue operation mode. (a) In expedite mode,
any Queue can be assigned 100% of CIR. Queue 4 is serviced first
and queue 1 is servcied last.(b) In non expedite mode, the sum of all CIRs
must be equal to 100%. In this mode higher priority queues
will be serviced first until that queue is emptied or
the defined CIR is reached.rw Enumeration .1.3.6.1.4.1.7262.2.2.13.6 |
hzOduCosQueueCIRCommitteed Information Rate (CIR) assignments for CoS queues
1 to 4. CIR is assigned as the percentage of system current speed.
When expedite queue is enabled any queue can be assigned 100% bandwidth.
When expedite queue is disabled the sum of CIR of all queues should be 100.rw DisplayString ( SIZE ( 0 .. 32 ) ) .1.3.6.1.4.1.7262.2.2.13.7 |
hzOduCosQueueCBSComitted Burst Size (CBS) for CoS queues 1 to 4. CBS is the percentage
of total packet buffer size. The sum of CBS's of all 4
queues must be equal to 100. Minimum CBS assignable to any queue
is 1.rw DisplayString ( SIZE ( 0 .. 32 ) ) .1.3.6.1.4.1.7262.2.2.13.8 |
hzOduCosDefaultValueDefault CoS value assigned to the ethernet
frames that don't have VLAN or Q-in-Q tag.rw INTEGER (0 .. 7) .1.3.6.1.4.1.7262.2.2.13.9 |
hzOduCutThroughProcessingSets cut through processing on/off.rw Enumeration .1.3.6.1.4.1.7262.2.2.13.10 |
hzOduRapidLinkShutdown OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.14 |
hzOduRapidLinkShutdownVer1 OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.14.1 |
hzOduRlsEnable<deprecated> The Rapid Link Shutdown feature: enabled or disabled.
Changing this option requires a system reset.rw Enumeration .1.3.6.1.4.1.7262.2.2.14.1.1 |
hzOduAutomaticLinkReestablish<deprecated> If this feature is enabled, the link will be automatically reestablished.
If this feature is disabled, the user must explicitly use the manualReestablish object
to bring the link back uprw Enumeration .1.3.6.1.4.1.7262.2.2.14.1.2 |
hzOduManualLinkReestablish<deprecated> This object is writeable ONLY if automaticLinkReestablish is set to disabled.
The user explicitly brings the link back up by setting this object to enabled.
The user explicitly brings the link down by setting this object to disabled.
to bring the link back uprw Enumeration .1.3.6.1.4.1.7262.2.2.14.1.3 |
hzOduHysterisisErredFramesPerMilliSecond<deprecated> The link will be automatically shut down when this number of erred
modem frames threshold is exceeded during the time set in the
hysterisisErredMilliSeconds object.
**NOTE: You must SET the writeRlsMonitorParametersToSystem object
to write this paramater to RAM. If you write and immediately
read this object, the previous value will be displayed.
You should SET all parameters in this folder first, and then write
to a '1' to the writeRlsMonitorParametersToSystem object.
You must also save the MIB via the writing the apSaveMIB object,
and then reset the system.rw INTEGER .1.3.6.1.4.1.7262.2.2.14.1.4 |
hzOduHysterisisErredMilliSeconds<deprecated> The time to determine a link that has excessive errors.
The link will be automatically shut down when this number of milliseconds
experiences the number of erred frames specified in the
hysterisisErredFramesPerMilliSecond object.
**NOTE: You must SET the writeRlsMonitorParametersToSystem object
to write this paramater to RAM. If you write and immediately
read this object, the previous value will be displayed.
You should SET all parameters in this folder first, and then write
to a '1' to the writeRlsMonitorParametersToSystem object.
You must also save the MIB via the writing the apSaveMIB object,
and then reset the system.rw INTEGER .1.3.6.1.4.1.7262.2.2.14.1.5 |
hzOduHysterisisUnerredFramesPerMilliSecond<deprecated> The link will be automatically brought back up when the number of erred
modem frames is less than this value ( only if automaticLinkReestablish
is set to enabled).
This threshold value cannot be crossed for the duration of time specified in the
hysterisisUnerredMilliSeconds object.
**NOTE: You must SET the writeRlsMonitorParametersToSystem object
to write this paramater to RAM. If you write and immediately
read this object, the previous value will be displayed.
You should SET all parameters in this folder first, and then write
to a '1' to the writeRlsMonitorParametersToSystem object.
You must also save the MIB via the writing the apSaveMIB object,
and then reset the system.rw INTEGER .1.3.6.1.4.1.7262.2.2.14.1.6 |
hzOduHysterisisUnerredMilliSeconds<deprecated> The time block to use to determine if the link is error free enough to
warrant it to automatically reestablish itself ( only if automaticLinkReestablish
is set to enabled).
The link will be brought back up automatically when this number of milliseconds
experiences less the number of acceptable erred frames specified in the
hysterisisUnerredFramesPerMilliSecond object.
**NOTE: You must SET the writeRlsMonitorParametersToSystem object
to write this paramater to RAM. If you write and immediately
read this object, the previous value will be displayed.
You should SET all parameters in this folder first, and then write
to a '1' to the writeRlsMonitorParametersToSystem object.
You must also save the MIB via the writing the apSaveMIB object,
and then reset the system.rw INTEGER .1.3.6.1.4.1.7262.2.2.14.1.7 |
hzOduWriteRlsMonitorParametersToSystem<deprecated> This writes the following parameters to RAM:
hysterisisErredFramesPerMilliSecond,
hysterisisErredMilliSeconds,
hysterisisUnerredFramesPerMilliSecond,
hysterisisUnerredMilliSeconds.
Reading this object returns '1'.rw INTEGER .1.3.6.1.4.1.7262.2.2.14.1.8 |
hzOduRlsSampleTimeInMilliSeconds<deprecated>rw INTEGER .1.3.6.1.4.1.7262.2.2.14.1.9 |
hzOduRapidLinkShutdownVer2 OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.14.2 |
hzOduPrimaryRlsEnableThe Rapid Link Shutdown feature: enabled or disabled.
Changing this option requires a system reset.rw Enumeration .1.3.6.1.4.1.7262.2.2.14.2.1 |
hzOduPrimaryRlsHardFaultMonitorThis object has changed - Enable the rlsHardFaultMonitor for rapid detection of severely degrade link. When disabled the
only the RLS Link Degrade Monitor is used.rw Enumeration .1.3.6.1.4.1.7262.2.2.14.2.2 |
hzOduPrimaryAutomaticLinkReestablishIf this feature is enabled, the link will be automatically reestablished
If this feature is disabled, the user must explicitly use the manualReestablish object
to bring the link back uprw Enumeration .1.3.6.1.4.1.7262.2.2.14.2.3 |
hzOduPrimaryManualLinkReestablishThis object is writeable ONLY if automaticLinkReestablish is set to disabled.
The user explicitly brings the link back up by setting this object to enabled.
The user explicitly brings the link down by setting this object to disabled.
to bring the link back uprw Enumeration .1.3.6.1.4.1.7262.2.2.14.2.4 |
hzOduWritePrimaryRlsMonitorParametersToSystemThis object has changed - This writes RLS soft and hard fault monitor parameters to RAM
Reading this object returns '1'.rw INTEGER .1.3.6.1.4.1.7262.2.2.14.2.5 |
hzOduPrimarySoftFaultMonitor OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.14.2.6 |
hzOduPrimaryEstablishErredFrameThresholdMaximum erred blocks, per sample, allowed for link establishment.rw INTEGER .1.3.6.1.4.1.7262.2.2.14.2.6.1 |
hzOduPrimaryShutdownErredFrameThresholdMinimum erred blocks, per sample, allowed before link shutdown.rw INTEGER .1.3.6.1.4.1.7262.2.2.14.2.6.2 |
hzOduPrimaryEstablishNumberOfSamplesMinimum number of consecutive good samples required before link is established.rw INTEGER .1.3.6.1.4.1.7262.2.2.14.2.6.3 |
hzOduPrimaryShutdownNumberOfSamplesMinimum number of consecutive erred samples before link is shutdown.rw INTEGER .1.3.6.1.4.1.7262.2.2.14.2.6.4 |
hzOduPrimaryEstablishSamplePeriodPeriod of Time, in milliseconds, for monitoring Establish Erred Frame Threshold.rw INTEGER .1.3.6.1.4.1.7262.2.2.14.2.6.5 |
hzOduPrimaryShutdownSamplePeriodPeriod of Time, in milliseconds, for monitoring Shutdown Erred Frame Threshold.rw INTEGER .1.3.6.1.4.1.7262.2.2.14.2.6.6 |
hzOduPrimaryQuickShutdownSamplePeriodMinimum number of milliseconds required to classify samples as erred.rw INTEGER .1.3.6.1.4.1.7262.2.2.14.2.6.7 |
hzOduPrimaryHardFaultMonitor OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.14.2.7 |
hzOduPrimaryFaultSamplePeriodThe period of time, in milliseconds, for which the
rlsFaultThreshold is applied.rw INTEGER .1.3.6.1.4.1.7262.2.2.14.2.7.1 |
hzOduPrimaryFaultThresholdThe percentage of the rlsFaultSamplePeriodMilliSeconds period
which must be degraded before the link is
set to the 'impaired' state.rw INTEGER .1.3.6.1.4.1.7262.2.2.14.2.7.2 |
hzOduPrimaryReceiveSignalLevelMonitor OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.14.2.8 |
hzOduPrimaryRlsMakeRslMonitorRslValueThe RSL threshold, in dBm. When Link is inactive and if RSL
is higher than this threshold for a desired
period, the link will become active.rw DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.2.2.14.2.8.1 |
hzOduPrimaryRlsMakeRslMonitorPeriodThe desired period, in seconds. When Link is inactive and if RSL
is higher than the desired threshold for this
period, the link will become active.rw INTEGER .1.3.6.1.4.1.7262.2.2.14.2.8.2 |
hzOduPrimaryRlsStatus OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.14.2.9 |
hzOduPrimaryRlsOptionRLS Option. On Basic: RLS enabled with base degrade monitoring;
On Advanced: RLS enabled with hard fault monitoring;
Off: Entire RLS feature disabled.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.14.2.9.1 |
hzOduPrimaryRlsStateRapid Link Shutdown State. If the state is activated, that means
link is down; If the state is inactivated, that means that
link is up.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.14.2.9.2 |
hzOduPrimaryRlsMismatchStateRLS Mismatch State. If the state is activated, that means RLS
configuration is mismatched with peer. If the state is OK,
that means RLS configuration is matched with peer.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.14.2.9.3 |
hzOduPrimaryDegradeMonitorStateDegrade Monitor State. If the state is activated, that means
the RLS Degrade Monitor is asserting the link down. If the
state is OK, that means the RLS Degrade Monitor is asserting
the link up.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.14.2.9.4 |
hzOduPrimaryHardFaultMonitorStateHard Fault Monitor State. If the state is activated, that means
the Hard Fault Monitor is asserting the link down. If the state
is OK, that means the RLS Hard Fault Monitor is asserting the
link up.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.14.2.9.5 |
hzOduPrimaryMakeRslThresholdStateMake RSL Threshold State. If the state is not met, that means the
RLS signal level is below the threshold value. If the state is OK,
that means the RLS signal level is above the threshold value.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.14.2.9.6 |
hzOduPrimaryPeerRslStatePeer RSL State. If the state is activated, that means the peer has
activated RLS. If the state is OK, that means the Peer hasn't
activated RLS.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.14.2.9.7 |
hzOduPrimaryRadioInterfaceStateRadio Interface State. If the state is down, that means The radio
interface is not operational(muted,disconnected, not configured).
If the state is up, that means the radio interface is operational.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.14.2.9.8 |
hzOduPrimaryNetworkInterfaceStateNetwork Interface State. If the state is down, that means the network
interface (Ethernet/PHY) is not operational(disconnected, not
configured). If the state is up, that means the network interface
(Ethernet/PHY) is operational.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.14.2.9.9 |
hzOduPrimaryUserConfiguredEstablishFerUser Configured Establish Frame Error Ratio required for the
link to be restored to service, set by the user. An example
value being '1.0E-7'.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.14.2.9.10 |
hzOduPrimaryMinimumAchievableEstablishFerMinimum achievable Frame Error Ratio required for the link to be
restored to service. An example value being '1.0E-7'.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.14.2.9.11 |
hzOduPrimaryUserConfiguredShutdownFerUser Configured Shutdown Frame Error Ratio required for the
link to remain in-service, set by the user. An example value
being '1.0E-7'.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.14.2.9.12 |
hzOduPrimaryMinimumAchievableShutdownFerMinimum achievable Frame Error Ratio required for the link to
remain in-service. An example value being '1.0E-7'.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.2.2.14.2.9.13 |
hzOduPrimaryUserConfiguredEstablishMonitorTimeUser Configured Establish Monitor Time, in milliseconds, for
which the 'User Configured Establish FER' must be achieved
to bring link into service, set by userro INTEGER .1.3.6.1.4.1.7262.2.2.14.2.9.14 |
hzOduPrimaryActualEstablishMonitorTimeActual Establish Monitor Time, in milliseconds, for which the
'User Configured Establish FER' must be achieved to bring
link into service, it's a multiple of the establish sample
period required to observe the FERro INTEGER .1.3.6.1.4.1.7262.2.2.14.2.9.15 |
hzOduPrimaryUserConfiguredShutdownMonitorTimeUser Configured Shutdown Monitor Time, in milliseconds, for which
the 'User Configured Shutdown FER' must be met for the link to
remain in-service, set by user.ro INTEGER .1.3.6.1.4.1.7262.2.2.14.2.9.16 |
hzOduPrimaryActualShutdownMonitorTimeActual Shutdown Monitor Time, in milliseconds, for which the 'User
Configured Shutdown FER' must be met for the link to remain
in-service, it's a multiple of the shutdown sample period required
to observe the FERro INTEGER .1.3.6.1.4.1.7262.2.2.14.2.9.17 |
hzOduSntp OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.15 |
hzOduSntpEnableIndicates whether SNTP feature is enabled.rw Enumeration .1.3.6.1.4.1.7262.2.2.15.1 |
hzOduSntpOffsetSystem time offset from GMT.rw INTEGER ( -140 .. 140 ) .1.3.6.1.4.1.7262.2.2.15.2 |
hzOduSntpServerTableTable containing sntp server entries SEQUENCE OF HzOduSntpServerEntry .1.3.6.1.4.1.7262.2.2.15.3 |
hzOduSntpServerEntryContains the sntp server information HzOduSntpServerEntry .1.3.6.1.4.1.7262.2.2.15.3.1 |
hzOduSntpServerIndexA unique value for each server.ro INTEGER .1.3.6.1.4.1.7262.2.2.15.3.1.1 |
hzOduSntpServerIpAddressThe IP address of the server.rw IpAddress .1.3.6.1.4.1.7262.2.2.15.3.1.2 |
hzOduSntpServerStatusThe status of the sntp server.ro Enumeration .1.3.6.1.4.1.7262.2.2.15.3.1.3 |
hzOduSntpServerStratumSpecifies the stratum of a server, 0 for failed serverro INTEGER .1.3.6.1.4.1.7262.2.2.15.3.1.4 |
hzOduLogs OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.16 |
hzOduEventLogEnableIndicates whether event log is enabled.rw Enumeration .1.3.6.1.4.1.7262.2.2.16.1 |
hzOduPerfmLogEnableIndicates whether performance log is enabled.rw Enumeration .1.3.6.1.4.1.7262.2.2.16.2 |
hzOduPerfmLogIntervalPerformance statistics are logged periodically by this interval.rw DisplayString ( SIZE ( 0 .. 10 ) ) .1.3.6.1.4.1.7262.2.2.16.3 |
hzOduRadius OBJECT IDENTIFIER .1.3.6.1.4.1.7262.2.2.17 |
hzOduRadiusSuperUserAuthenticationThe set strict mode on or offrw Enumeration .1.3.6.1.4.1.7262.2.2.17.1 |
hzOduRadiusServerTimeOutTimeout period for authentication requestsro INTEGER .1.3.6.1.4.1.7262.2.2.17.2 |
hzOduRadiusServerDeadTimeTime to declare an unresponsive server 'dead'ro INTEGER .1.3.6.1.4.1.7262.2.2.17.3 |
hzOduRadiusServerReTransmitMaximum number of retransmits to an unresponsive serverro Enumeration .1.3.6.1.4.1.7262.2.2.17.4 |
hzOduRadiusServerTableTable containing radius server entries SEQUENCE OF HzOduRadiusServerEntry .1.3.6.1.4.1.7262.2.2.17.5 |
hzOduRadiusServerEntryContains the sntp server information HzOduRadiusServerEntry .1.3.6.1.4.1.7262.2.2.17.5.1 |
hzOduRadiusServerIndexA unique value for each server.ro INTEGER .1.3.6.1.4.1.7262.2.2.17.5.1.1 |
hzOduRadiusCfgdHostIpAddressThe IP address of the configured radius server.rw IpAddress .1.3.6.1.4.1.7262.2.2.17.5.1.2 |
hzOduRadiusActiveHostIpAddressThe IP address of the active radius server.ro IpAddress .1.3.6.1.4.1.7262.2.2.17.5.1.3 |